![]() |
COMMAND DESCRIPTION 17/190 82-CRA 119 1170/1-V1 Uen A | ![]() |
Copyright
© Copyright Ericsson AB 2009. All rights reserved.
Disclaimer
No part of this document may be reproduced in any form without the written permission of the copyright owner. The contents of this document are subject to revision without notice due to continued progress in methodology, design and manufacturing. Ericsson shall have no liability for any error or damage of any kind resulting from the use of this document.
Trademark List
SmartEdge | is a registered trademark of Telefonaktiebolaget L M Ericsson. | |
NetOp | is a trademark of Telefonaktiebolaget L M Ericsson. |
Commands starting with “show b” are included.
For ports on channelized OC-12 traffic cards, the syntax is:
show bert slot/port:ds3-chan-num[:ds1-chan-num]
For channelized ports on DS-3 traffic cards, the syntax is:
show bert slot/port[:ds1-chan-num]
For clear-channel ports on DS-3 or E3 traffic cards, or ports on Asynchronous Transfer Mode (ATM) DS-3 traffic cards, the syntax is:
show bert slot/port
Displays Bit Error Rate Tester (BERT) results for an ATM DS-3, clear-channel DS-3, or E3 port, or a DS-1 or clear-channel DS-3 channel.
all modes
slot |
Chassis slot number of the traffic card with the port being tested. |
port |
Port number being tested. |
ds3-chan-num |
Optional. DS-3 channel number on the on the channelized OC-12 port being tested. The range of values is 1 to 12. |
ds1-chan-num |
Optional. DS-1 channel number on the channelized DS-3 channel or port being tested. If omitted, the DS-3 channel must be clear-channel. The range of values is 1 to 28. |
Displays results for all channels on the port.
Use the show bert command to display BERT results for a port or channel.
Similarly, if you have specify a 2^20 bit pattern for an E3 port and the far-end equipment is configured with the all-zeros bit pattern, the E3 port synchronizes with the all-zeros pattern and counts the deviations from the all-zeros pattern instead of the configured pattern.
The output of this command displays the configured bit pattern, not the pattern that the E3 port synchronized to; therefore, before interpreting the resulting BERT status and statistics, verify that the configured bit patterns for the E3 port and far-end equipment match.
The following example displays the BERT output for the channelized OC-12 traffic card in slot 2, port 1, DS-3 channel 1, DS-1 channel 1:
[local]Redback>show bert 2/1:1:1
BERT stats for port 2/1:1:1 State : Enabled Pattern : 1s Interval : 1 minute(s) Injected err rate : None Time remaining : 00:00:40 Total errors : 0 Elapsed sync time : 00:00:00 Errors this sync : 0 Sync count : 0
The following example displays the BERT output for the ATM DS-3 traffic card in slot 13, port 3:
[local]Redback>show bert 13/3
BERT stats for port 13/3 State : Active Pattern : 2^15 Interval : 3 minute(s) Injected err rate : 1 in 100 milliseconds Time remaining : 00:02:45 Total errors : 0 Elapsed sync time : 00:00:15 Errors this sync : 134 Sync count : 1
show bfd session [ip-addr] [detail] [all-context]
Displays active Bidirectional Forwarding Detection (BFD) session information for neighbors in the current context.
ip-addr |
Optional. BFD neighbor IP address in the form A.B.C.D. |
detail |
Optional. Displays detailed information. |
all-context |
Optional. Displays BFD session information for all contexts. This option is only valid in the local context. |
Active BFD session information for all neighbors is displayed.
Use the show bfd session command to display active BFD session information for neighbors in the current context.
If the optional neighbor IP address is specified, only the session to that neighbor is displayed.
The following example displays BFD session information:
[local]Redback>show bfd session Neighbor Next-hop Minimum Multiplier State Constituents Tx/Rx intvl 1.1.1.2 31700004 1000/1000 3 Down 2
The following example displays detailed BFD session information:
[local]Redback>show bfd session detail BFD Neighbor: 1.1.1.2 BFD interface grid: 0x10000001 Context id: 0x40080001 Next-hop grid: 0x31700004 Circuit: 255/11:1023:63/1/2/5 Configured Transmit interval: 1000 Receive interval: 1000 Multiplier: 3 Constituents: Next-hop grid: 0x34500007 Circuit: 2/8:1023:63/1/2/28 Local discriminator: 0x2081a1f Remote discriminator: 0x2091a20 State: Down Previous State: Up Local diag: Neighbour signalled sess down Source IP addr: 1.1.1.1 Source UDP port: 49157 Received Transmit interval: 1000 Receive interval: 1000 Multiplier: 3 Next-hop grid: 0x34500008 Circuit: 2/6:1023:63/1/2/22 Local discriminator: 0x2061a15 Remote discriminator: 0x2071a19 State: Down Previous State: Init Local diag: Detection timer expired Source IP addr: 1.1.1.1 Source UDP port: 49156 Received Transmit interval: 1000 Receive interval: 1000 Multiplier: 3
show bgp attribute {as-path | community | nexthop | rrinfo | summary}
Displays Border Gateway Protocol (BGP) attribute information.
all modes
as-path |
Displays autonomous system (AS) path information. |
community |
Displays community information. |
nexthop |
Displays next-hop information. |
rrinfo |
Displays route reflector information. |
summary |
Displays attribute summary information. |
None
Use the show bgp attribute command to display BGP attribute information.
Table 1 describes the output fields for the show bgp attribute nexthop command.
Field |
Description |
---|---|
Next Hop |
IP address of the next-hop neighbor. |
Metric |
Metric value used. |
Ref-count |
Number of routes that use the next-hop attribute. |
Context-Id |
Context ID number. |
Interface-id |
Interface ID number. |
Table 2 describes the output fields for the show bgp attribute summary command.
Field |
Description |
---|---|
Entry Type |
Attribute type. |
Count |
Number of times the attribute has been applied. |
Memory |
Amount, in bytes, of memory used to process the application of attribute for the specified count. |
Policy Cache Type |
Type of routing policy. |
Count |
Number times the policy has been applied. |
Memory |
Amount, in bytes, of memory used to process the application of the routing policy for the specified count. |
The following example displays output from the show bgp attribute as-path command:
[local]Redback>show bgp attribute as-path
RefCount Aspath 2 14207 3944 2548 3549 20012 2 64513 2828 5511 4000 3662 4528 1 14207 3944 2548 6461 7086 1 14207 3944 2548 3561 5378 6779 1 64513 2828 209 4766 9754 2 64513 2828 6453 8657 1930 1930 3251 1 64513 2828 1239 2516 2521 1 14207 3944 2548 701 814
The following example displays output from the show bgp attribute community command:
[local]Redback>show bgp attribute community
Community entries: 3, memory used: 116 bytes RefCount Community 14181 11:102 2 11:121 2 no-export
The RefCount field indicates how many attributes use the corresponding community.
The following example displays output from the show bgp attribute nexthop command:
[local]Redback>show bgp attribute nexthop
Next hop entries: 5 Next Hop Metric Ref-count Context-Id Interface-id 10.255.255.254 0 1 40080001 0 10.100.1.102 39 2 40080001 0 10.11.64.100 0 93378 40080001 10000006 10.100.1.5 25 2 40080001 0 10.100.2.3 30 9 40080001 0
The following example displays output from the show bgp attribute rrinfo command:
[local]Redback>show bgp attribute rrinfo
RRinfo entries: 6, memory used: 196 bytes RefCount Originator Cluster-list 45 1.1.1.71 0.0.0.11 12 1.1.1.72 0.0.0.11 2 1.1.1.74 0.0.0.11 14 100.1.1.1 0.0.0.11 133 10.100.5.1 0.0.0.11 32 10.100.2.3 0.0.0.11 10.100.12.0
The following example displays output from the show bgp attribute summary command:
[local]Redback>show bgp attribute summary
Entry Type Count Memory Attribute 31595 1516560 ASpath 12723 506620 Nexthop 13 364 Community 4 116 Ext Community 0 0 Route Reflection 8 228 Policy Cache Type Count Memory AS-path List 38082 1218624 Community List 4 128 Route Map 43990 1407680 Attributes 16724 535168
show bgp attribute extended-community
Displays Border Gateway Protocol (BGP) attribute information for extended communities.
all modes
This command has no keywords or arguments.
None
Use the show bgp attribute extended-community command to display BGP attribute information for extended communities.
The following example displays output from the show bgp attribute extended-community command:
[local]Redback>show bgp attribute extended-community
Extended community entries: 3, memory used: 132 bytes RefCount Extended community 21132 RT:4:4 21132 RT:6:6 21128 RT:5:5
show bgp malform {messages [keepalive | notification | open | refresh] | update}
Displays malformed Border Gateway Protocol (BGP) messages for troubleshooting purposes.
all modes
messages |
Displays malformed BGP nonupdate messages. |
keepalive |
Optional. Displays only malformed keepalive messages. |
notification |
Optional. Displays only malformed notification messages. |
open |
Optional. Displays only malformed open messages. |
refresh |
Optional. Displays only malformed refresh messages. |
update |
Displays malformed BGP update messages. |
None
Use the show bgp malform command to display malformed BGP messages for troubleshooting purposes.
The following example enables the display of malformed BGP update messages:
[local]Redback>show bgp malform update
show bgp neighbor [{ip-addr | ipv6-addr/prefix-length} [malform {messages [keepalive | notification | open | refresh] | update}] [notification] [received] [reset-log] | summary]
Displays Border Gateway Protocol (BGP) neighbor status and statistics.
all modes
ip-addr |
Optional. IP address of the neighbor, in the form A.B.C.D. |
ipv6-addr/prefix-length |
Optional. IPv6 address and prefix length, separated by the slash (/) character. The range of values for the prefix-length argument is 0 to 128. |
malform |
Optional. Displays either malformed update or nonupdate messages. |
messages |
Optional. Displays malformed nonupdate messages. |
keepalive |
Optional. Displays only malformed keepalive messages. |
notification |
Optional. Displays only malformed notification messages. |
open |
Optional. Displays only malformed open messages. |
refresh |
Optional. Displays only malformed refresh messages. |
update |
Optional. Displays only malformed update messages. |
received |
Optional. Displays received address information. |
reset-log |
Optional. Displays how many times the BGP neighbor has been reset and for what reason the neighbor has been reset. |
summary |
Optional. Displays summary statistics for all BGP neighbors. |
When entered with no keywords or arguments, this command displays information for all BGP neighbors.
Use the show bgp neighbor command to display BGP status and statistics for all BGP neighbors, or for a specific BGP neighbor.
The following example displays sample output from the show bgp neighbor command:
[local]Redback>show bgp neighbor
BGP neighbor: 23.23.23.23, remote AS: 1, internal link Version: 4, router identifier: 100.100.100.101 State: Established for 00:21:24 Last read 00:00:34, last send 00:00:54 Hold time: configured 180, negotiated 180 Keepalive time: configured 60, negotiated 60 Local restart timer 120 sec, stale route retain timer 180 sec Received restart timer 120 sec, flag 0x0 Minimum time between advertisement runs: 5 secs Source IP address used from interface: loopmolly Source (local) IP address: 22.22.22.22 Received messages: 6201 (2512469 bytes), notifications: 0, in queue: 0 Sent messages: 25 (626 bytes), notifications: 0, out queue: 0 CapSent: refresh, 4byteAS, unicast, v6vpn, restart CapRcvd: refresh, 4byteAS, unicast, v6vpn restart (time 120, flags 0x0, unicast, v6vpn) Address family: ipv4 unicast BGP table version: 0, neighbor version: 0 Routes: rcvd 0, imported 0, active 0, history 0, dampend 0, sent 0 Address family: ipv6 vpn BGP table version: 144877, neighbor version: 144877 Route refresh requests: sent 1, received 1 Routes: rcvd 0, imported 0, active 0, history 0, dampend 0, sent 1
The following example displays information for BGP neighbor with the IP address, 22.22.22.22
[local]Redback>show bgp neighbor 22.22.22.22 BGP neighbor: 22.22.22.22, remote AS: 1, internal link Version: 4, router identifier: 22.22.22.22 State: Established for 00:55:29 Last read 00:00:53, last send 00:00:37 Hold time: configured 180, negotiated 180 Keepalive time: configured 60, negotiated 60 Local restart timer 120 sec, stale route retain timer 180 sec Received restart timer 120 sec, flag 0x0 Minimum time between advertisement runs: 5 secs Source (local) IP address: 23.23.23.23 Received messages: 59 (1272 bytes), notifications: 0, in queue: 0 Sent messages: 6235 (2513115 bytes), notifications: 0, out queue: 0 CapSent: refresh, 4byteAS, unicast, v6vpn, restart CapRcvd: refresh, 4byteAS, unicast, v6vpn restart (time 120, flags 0x0, unicast, v6vpn) Address family: ipv4 unicast BGP table version: 0, neighbor version: 0 Routes: rcvd 0, imported 0, active 0, history 0, dampend 0, sent 0 Address family: ipv6 vpn BGP table version: 72484, neighbor version: 72484 Route refresh requests: sent 1, received 1 Routes: rcvd 1, imported 1, active 2, history 0, dampend 0, sent 24146
The following example displays output from the show bgp neighbor summary command:
[local]Redback>show bgp neighbor summary BGP router identifier: 100.100.100.101, local AS number: 1 Neighbors Configured: 7, Established: 3 Neighbor AS MsgRcvd MsgSent InQ OutQ Rst Up/Down State 1.1.1.1 1 15 2878 0 0 0 00:09:50 Established CapSent : refresh 4byteAS vpn v6vpn restart CapRcvd : refresh 4byteAS unicast vpn v6unicast v6vpn restart vpn : rcvd: 1 imported: 0 active: 1 history: 0 dampened: 0 sent: 20026 v6vpn : rcvd: 1 imported: 0 active: 1 history: 0 dampened: 0 sent: 24146 3.1.4.1 1 72 4994 0 0 0 01:06:01 Established CapSent : refresh 4byteAS unicast vpn v6vpn restart CapRcvd : refresh 4byteAS unicast vpn v6vpn restart unicast : rcvd: 0 imported: 0 active: 0 history: 0 dampened: 0 sent: 0 vpn : rcvd: 5 imported: 5 active: 10 history: 0 dampened: 0 sent: 20026 v6vpn : rcvd: 0 imported: 0 active: 0 history: 0 dampened: 0 sent: 24146 10.1.0.65 1 0 0 0 0 0 01:09:19 Connect CapSent : refresh 4byteAS unicast vpn restart 15.5.19.78 1 0 0 0 0 0 01:09:19 Connect CapSent : refresh 4byteAS unicast vpn restart 22.22.22.22 1 58 6234 0 0 0 00:53:54 Established CapSent : refresh 4byteAS unicast v6vpn restart CapRcvd : refresh 4byteAS unicast v6vpn restart unicast : rcvd: 0 imported: 0 active: 0 history: 0 dampened: 0 sent: 0 v6vpn : rcvd: 1 imported: 1 active: 2 history: 0 dampened: 0 sent: 24146 99.99.1.1 1 0 0 0 0 0 01:09:19 Connect CapSent : refresh 4byteAS unicast vpn restart 100.100.100.100 1 0 0 0 0 0 01:09:19 Connect CapSent : refresh 4byteAS unicast vpn restart
show bgp neighbor flap-statistics
Displays Border Gateway Protocol (BGP) neighbor flap statistics information.
all modes
This command has no keywords or arguments.
None
Use the show bgp neighbor flap-statistics command to display BGP neighbor flap statistics information.
Table 3 describes the output fields for the show bgp neighbor flap-statistics command.
Field |
Description |
---|---|
Neighbor |
Flapping peer. The letter d (before a peer’s IP address) indicates that the peer is dampened. |
AS |
Peer’s autonomous system (AS). |
Flap |
Number of times the peer has been flapping for the time indicated in the Duration column. |
Penalty |
The current penalty applied to the session. |
Duration |
Length of time that the session has been flapping in the current dampening information. |
Reuse |
Time (in hours:minutes:seconds) after which the session will be allowed to open again. |
The following example displays output from the show bgp neighbor flap-statistics command:
[local]Redback>show bgp neighbor flap-statistics
Neighbor AS Flap Penalty Duration Reuse d 1.1.1.1 100 5 4164 00:13:39 00:08:35 3.3.3.3 200 2 1977 00:00:13
show bgp notification
Displays Border Gateway Protocol (BGP) notification messages for troubleshooting purposes.
all modes
This command has no keywords or arguments.
None
Use the show bgp notification command to display BGP notification messages for troubleshooting purposes.
The following example displays BGP notification messages:
[local]Redback>show bgp notification
Dump notification messaged logged: Nov 9 00:36:03 notification msg received (nbr 192.168.3.7, 21 bytes, repeated 0 times, code 4/0 (hold time expired) - ffff ffff ffff ffff ffff ffff ffff ffff 0015 0304 00 Nov 9 00:36:23 notification msg received (nbr 192.168.41.7, 21 bytes, repeated 0 times, code 4/0 (hold time expired) - ffff ffff ffff ffff ffff ffff ffff ffff 0015 0304 00
show bgp peer-group {group-name [member {ipv4 {multicast | unicast} | session}] | summary}
Displays information about configured Border Gateway Protocol (BGP) peer groups.
all modes
group-name |
Peer group name. |
member |
Optional. Displays address family information for the specified peer group. |
ipv4 |
Specifies standard IP Version 4 (IPv4) address prefixes. |
multicast |
Displays information for multicast address families associated with the peer group. |
unicast |
Displays information for unicast address families associated with the peer group. |
session |
Displays BGP session information for the specified peer group. |
summary |
Displays a summarized set of information for all configured BGP peer groups. |
None
Use the show bgp peer-group command to display information about configured BGP peer groups.
The following example displays output from the show bgp peer-group command:
[local]Redback>show bgp peer-group bgp1
BGP peer-group: bgp1, external link Version: 4, router identifier: 0.0.0.0 Description: external BGP group 1 Hold time: configured 180, negotiated 0 Keepalive time: configured 60, negotiated 0 Local restart timer 120 sec, stale route retain timer 180 sec Received restart timer 0 sec, flag 0x0 Number of hops external BGP neighbor may be away: 1 Minimum time between advertisement runs: 30 secs Source (local) IP address: 0.0.0.0 Fast reset timer 1234 msecs Interface name: to-2/1 State: DOWN Interface name: to-mardi State: DOWN Interface name: to-onze State: UP Address family: ipv4 unicast BGP table version: 1394616, neighbor version: 0 Messages: formatted 0, replicated 0 Prefixes: advertised 0, accepted 0, active 0 Address family: ipv4 multicast BGP table version: 0, neighbor version: 0 Messages: formatted 0, replicated 0 Prefixes: advertised 0, accepted 0, active 0
The following example displays BGP peer group summary information:
[local]Redback>show bgp peer-group summary
BGP router identifier: 7.7.7.2, local AS number: 64173 Peer-group Configured: 1 (internal 0, external 1) Peer-group Name Type full-routes external
The following example displays BGP peer group member information:
[local]Redback>show bgp peer-group full-routes member
BGP peer-group: full-routes, external link Neighbor AS MsgRcvd MsgSent TblVer InQ OutQ Rst Up/Down PfxRcvd/Sent 10.13.49.172 64172 200645 253642 287452 0 0 12 00:03:46 0 92248 155.53.1.235 14207 5589 66910 287452 0 0 1 02:41:21 92242 92248
show bgp reset-log
Displays Border Gateway Protocol (BGP) neighbor reset information for troubleshooting purposes.
all modes
This command has no keywords or arguments.
None
Use the show bgp reset-log command to display information about BGP neighbor resets for troubleshooting purposes.
The following example displays output from the show bgp reset-log command:
[local]Redback>show bgp reset-log
Dump neighbor reset logs: Neighbor StartTime EndTime Count Reason 192.168.3.7 Nov 9 00:36:03 Nov 9 00:36:03 1 Remote/TCP close 192.168.41.7 Nov 9 00:36:23 Nov 9 00:36:23 1 Remote/TCP close 192.168.3.7 Nov 9 01:21:35 Nov 9 01:21:35 1 User action
show bgp route [ip-addr[/prefix-length]] [longer-prefixes]
Displays Border Gateway Protocol (BGP) route information from the BGP routing table.
all modes
ip-addr |
Optional. IP address, in the form A.B.C.D. |
prefix-length |
Optional. Prefix length. The range of values is 0 to 32. |
longer-prefixes |
Optional. Available only when the /prefix-length construct is used. Displays routes sent to and from the specified prefix and also displays more-specific routes. |
When entered without any keywords or arguments, this command displays information for all BGP routes.
Use the show bgp route command to display BGP route information from the BGP routing table.
The following example displays output from the show bgp route command:
[local]Redback>show bgp route
Address Family: ipv4 unicast BGP table version is 292821, local router ID is 192.168.41.100 Status codes: d damped, h history, > best, i internal Origin codes: i - IGP, e - EGP, ? - incomplete Network Next Hop Metric LocPrf Weight Path 1.0.0.0/8 155.53.0.1 0 100 100 14207 3944 7777 i 1.2.3.4/32 192.168.41.7 0 100 100 64173 ? I 2.0.0.0/8 155.53.0.1 200 100 100 14207 3944 7777 i 155.53.0.1 0 100 100 14207 3944 7777 i 2.1.0.0/16 192.168.41.7 0 100 100 64173 100 ? 2.3.0.0/16 192.168.41.7 0 100 100 64173 100 ? I 3.0.0.0/8 155.53.0.1 200 100 100 14207 3944 2914 701 80 i 155.53.0.1 0 100 100 14207 3944 2914 701 80 i 3.18.135.0/24 155.53.0.1 0 100 100 14207 64513 2828 2828 2828 2828 7018 ? I 155.53.1.236 200 100 100 64513 2828 2828 2828 2828 7018 ? I 4.0.0.0/8 155.53.0.1 200 100 100 14207 3944 2914 1 i 155.53.0.1 0 100 100 14207 3944 2914 1 i 4.2.1.1/32 192.168.41.7 0 100 100 64173 100 ? I 4.3.24.3/32 155.53.0.1 200 100 100 14207 3944 7777 i 155.53.0.1 0 100 100 14207 3944 7777 i I 4.21.238.51/32 155.53.0.1 200 100 100 14207 3944 7777 i 155.53.0.1 0 100 100 14207 3944 7777 i I 4.22.124.174/31 155.53.0.1 200 100 100 14207 3944 7777 i 155.53.0.1 0 100 100 14207 3944 7777 i I 4.22.124.176/32 155.53.0.1 200 100 100 14207 3944 7777 i 155.53.0.1 0 100 100 14207 3944 7777 i I 4.22.124.197/32 155.53.0.1 200 100 100 14207 3944 7777 i 155.53.0.1 0 100 100 14207 3944 7777 i
show bgp route community {community-num | as:nn | local-as | no-advertise | no-export}
Displays Border Gateway Protocol (BGP) route community information.
all modes
community-num |
Community number in decimal format. The range of values is 0 to 4,294,967,295. |
as:nn |
Autonomous system number (ASN) where aa is the ASN and nn is a 2-byte number. |
local-as |
Displays routes for the local autonomous system (AS). |
no-advertise |
Displays routes that are not advertised to internal BGP (iBGP) or external BGP (eBGP) peers. |
no-export |
Displays routes that are sent only to iBGP peers. |
When entered without any keywords or arguments, this command displays all route community information.
Use the show bgp route community command to display BGP route community information.
The following example displays routes matching the BGP community, 2914:420:
[local]Redback>show bgp route community 2914:420
Address Family: ipv4 unicast BGP table version is 292841, local router ID is 192.168.41.100 Status codes: d damped, h history, > best, i internal Origin codes: i - IGP, e - EGP, ? - incomplete Network Next Hop Metric LocPrf Weight Path 3.0.0.0/8 155.53.0.1 0 100 100 14207 3944 2914 701 80 i i 4.0.0.0/8 155.53.0.1 200 100 100 14207 3944 2914 1 i 155.53.0.1 0 100 100 14207 3944 2914 1 i i 6.0.0.0/20 155.53.0.1 200 100 100 14207 3944 2914 3549 i 155.53.0.1 0 100 100 14207 3944 2914 3549 i i 6.1.0.0/16 155.53.0.1 200 100 100 14207 3944 2914 7170 1455 i 155.53.0.1 0 100 100 14207 3944 2914 7170 1455 i i 6.3.0.0/18 155.53.0.1 200 100 100 14207 3944 2914 7170 1455 i
The following example displays routes matching the BGP community, 7777:7777:
[local]Redback>show bgp route community 7777:7777
Address Family: ipv4 unicast BGP table version is 292862, local router ID is 192.168.41.100 Status codes: d damped, h history, > best, i internal Origin codes: i - IGP, e - EGP, ? - incomplete Network Next Hop Metric LocPrf Weight Path 1.0.0.0/8 155.53.0.1 0 100 100 14207 3944 7777 i i 2.0.0.0/8 155.53.0.1 200 100 100 14207 3944 7777 i 155.53.0.1 0 100 100 14207 3944 7777 i i 5.0.0.0/8 155.53.0.1 200 100 100 14207 3944 7777 i 155.53.0.1 0 100 100 14207 3944 7777 i i 7.0.0.0/8 155.53.0.1 200 100 100 14207 3944 7777 i 155.53.0.1 0 100 100 14207 3944 7777 i i 23.0.0.0/8 155.53.0.1 200 100 100 14207 3944 7777 i 155.53.0.1 0 100 100 14207 3944 7777 i i 27.0.0.0/8 155.53.0.1 200 100 100 14207 3944 7777 i 155.53.0.1 0 100 100 14207 3944 7777 i i 36.0.0.0/8 155.53.0.1 200 100 100 14207 3944 7777 i 155.53.0.1 0 100 100 14207 3944 7777 i
show bgp route ext-community route-target ext-com
Displays Border Gateway Protocol (BGP) routes for a specific route target extended community.
all modes
ext-com |
Route target extended community value that is added to the export target list. The route target extended community value can be expressed in either of the following formats:
|
None
Use the show bgp route ext-community route-target command to display BGP routes for a specific route target extended community.
The following example displays the BGP routes for the route target extended community, 2:2:
[local]Redback>show bgp route ext-community route-target 2:2
Address Family: ipv4 unicast BGP table version is 4, local router ID is 2.2.2.2 Status codes: d damped, h history, > best, i internal Origin codes: i - IGP, e - EGP, ? - incomplete VPN RD: 2:2 Network Next Hop Metric LocPrf Weight Path >i 55.55.55.55/32 1.1.1.100 101 100 100 ? >i 77.1.1.0/24 1.1.1.100 0 100 100 ?
show bgp route flap-statistics [dampened-path | external | internal]
Displays Border Gateway Protocol (BGP) route-flap statistics accounting information.
all modes
dampened-path |
Optional. Displays only BGP routes suppressed due to dampening. |
external |
Optional. Displays only route-flap statistics for external BGP (eBGP) routes. |
internal |
Optional. Displays only route-flap statistics for internal BGP (iBGP) routes. |
None
Use the show bgp route flap-statistics command to display BGP route-flap statistics accounting information.
The following example displays output from the show bgp route flap-statistics command:
[local]Redback>show bgp route flap-statistics
Address Family: ipv4 unicast BGP table version is 418695, local router ID is 192.168.4.100 Status codes: d damped, h history, > best, i internal Origin codes: i - IGP, e - EGP, ? - incomplete Network From Flaps Penalty Duration Reuse Path i 15.252.0.0/18 10.12.208.81 1 500 00:00:01 14207 3944 6461 7018 71 i 15.252.64.0/20 10.12.208.81 1 500 00:00:01 14207 3944 6461 7018 71 >i 192.6.41.0/24 10.12.208.72 1 500 00:00:00 14207 3944 6461 701 71 i 10.12.208.81 1 500 00:00:01 14207 3944 6461 701 71 >i 195.82.32.0/19 10.12.208.72 1 1000 00:00:05 14207 3944 6461 9126 8375 i 10.12.208.81 1 500 00:00:01 14207 3944 6461 9126 8375 hi 198.235.184.0/24 10.12.208.72 1 1000 00:00:00 14207 64513 2828 2828 2828 2828 701 6539 549 hi 10.12.208.81 1 992 00:00:10 64513 2828 2828 2828 2828 701 6539 549 ........ h 130.235.0.0/16 192.168.41.7 6 2224 00:16:59 64173 14207 3944 6461 286 2603 1653 2846 2846 h 130.235.56.0/21 192.168.41.7 4 1129 00:20:01 64173 14207 64513 2828 2828 2828 2828 209 286 2603 1653 2846 h 130.235.184.0/21 192.168.41.7 4 1129 00:20:01 64173 14207 64513 2828 2828 2828 2828 209 286 2603 1653 2846 134.114.0.0/16 192.168.41.7 2 419 00:19:10 64173 14207 3944 6461 701 3908 2900 144.173.0.0/16 192.168.41.7 2 648 00:09:34 64173 14207 3944 6461 786 h 156.70.0.0/16 192.168.41.7 1 428 00:18:17 64173 14207 3944 6461 1239 5676 159.226.0.0/16 192.168.41.7 4 988 00:17:48 64173 14207 3944 6461 5727 7497 h 160.8.0.0/16 192.168.41.7 8 1183 01:15:52 64173 14207 3944 6461 1239 5511 2874 d 209.211.0.0/22 192.168.41.7 7 1524 00:55:38 64173 14207 3944 6461 209
The following example displays output from the show bgp route flap-statistics dampened-path command:
[local]Redback>show bgp route flap-statistics dampened-path
Address Family: ipv4 unicast BGP table version is 418715, local router ID is 192.168.4.100 Status codes: d damped, h history, > best, i internal Origin codes: i - IGP, e - EGP, ? - incomplete Network From Flaps Penalty Duration Reuse Path d 209.211.0.0/22 192.168.41.7 7 1524 00:55:38 00:15:45 64173 14207 3944 6461 209
The following example displays output from the show bgp route flap-statistics external command:
[local]Redback>show bgp route flap-statistics external
Address Family: ipv4 unicast BGP table version is 418994, local router ID is 192.168.4.100 Status codes: d damped, h history, > best, i internal Origin codes: i - IGP, e - EGP, ? - incomplete Network From Flaps Penalty Duration Reuse Path 63.105.82.0/23 192.168.41.7 1 431 00:03:09 64173 14207 64513 2828 2828 2828 2828 3356 17074 63.163.214.0/24 192.168.41.7 1 388 00:05:23 64173 14207 64513 2828 2828 2828 2828 1239 13776 63.210.250.0/23 192.168.41.7 2 855 00:03:35 64173 14207 64513 2828 2828 2828 2828 3356 17074 63.210.252.0/23 192.168.41.7 2 855 00:03:35 64173 14207 64513 2828 2828 2828 2828 3356 17074 64.84.0.0/18 192.168.41.7 2 823 00:06:39 64173 14207 3944 6461 1239 10738 h 65.169.76.0/24 192.168.41.7 1 846 00:03:35 64173 14207 64513 2828 2828 2828 2828 1239 22083 h 65.195.55.0/24 192.168.41.7 1 688 00:07:54 64173 14207 64513 2828 2828 2828 2828 701 19623 h 130.235.0.0/16 192.168.41.7 6 1277 00:29:09 64173 14207 3944 6461 286 2603 1653 2846 2846
The following example displays output from the show bgp route flap-statistics internal command. The flap-statistics command (in BGP address family configuration mode) must be enabled to see flap statistics for iBGP peers:
[local]Redback>show bgp route flap-statistics internal
Address Family: ipv4 unicast BGP table version is 419481, local router ID is 192.168.4.100 Status codes: d damped, h history, > best, i internal Origin codes: i - IGP, e - EGP, ? - incomplete Network From Flaps Penalty Duration Reuse Path i 15.252.0.0/18 10.12.208.81 1 500 00:00:01 14207 3944 6461 7018 71 i 15.252.64.0/20 10.12.208.81 1 500 00:00:01 14207 3944 6461 7018 71 >i 192.6.41.0/24 10.12.208.72 1 500 00:00:00 14207 3944 6461 701 71 i 10.12.208.81 1 500 00:00:01 14207 3944 6461 701 71 >i 195.82.32.0/19 10.12.208.72 1 1000 00:00:05 14207 3944 6461 9126 8375 i 10.12.208.81 1 500 00:00:01 14207 3944 6461 9126 8375
show bgp route inconsistent-as
Displays Border Gateway Protocol (BGP) routes sourced from more than one autonomous system (AS).
all modes
This command has no keywords or arguments.
None
Use the show bgp route inconsistent-as command to display BGP routes sourced from more than one AS.
The following example displays output from the show bgp route inconsistent-as command:
[local]Redback>show bgp route inconsistent-as
Address Family: ipv4 unicast BGP table version is 418763, local router ID is 192.168.4.100 Status codes: d damped, h history, > best, i internal Origin codes: i - IGP, e - EGP, ? - incomplete Network Next Hop Metric LocPrf Weight Path >i 192.231.3.0/24 155.53.1.235 0 100 100 14207 3944 6461 1 239 5696 10943 i 192.168.41.7 0 100 100 64173 14207 3944 6461 1239 5696 10943 i i 155.53.1.236 0 100 100 64513 2828 2828 2 828 2828 3561 i >i 198.148.166.0/24 155.53.1.235 0 100 100 14207 3944 6461 7 01 1673 1322 1335 8174 18920 i 192.168.41.7 0 100 100 64173 14207 3944 6461 701 1673 1322 1335 8174 18920 i i 155.53.1.236 0 100 100 64513 2828 2828 2 828 2828 701 703 4716 9999 i >i 198.203.153.0/24 155.53.1.235 0 100 100 14207 3944 6461 1 239 5696 10943 i 192.168.41.7 0 100 100 64173 14207 3944 6461 1239 5696 10943 i i 155.53.1.236 0 100 100 64513 2828 2828 2
show bgp route ipv4 {multicast | unicast}
Displays information for Border Gateway Protocol (BGP) multicast or unicast IP Version 4 (IPv4) address prefix-based routes.
all modes
multicast |
Displays information only for multicast routes using IPv4 address prefixes. |
unicast |
Displays information only for unicast routes using IPv4 address prefixes. |
None
Use the show bgp route ipv4 command to display information for BGP multicast or unicast IPv4 address prefix-based routes.
The following example displays output from the show bgp route ipv4 command:
[local]Redback>show bgp route ipv4
Address Family: ipv4 unicast BGP table version is 2265175, local router ID is 1.1.1.78 Status codes: d damped, h history, > best, i internal Origin codes: i - IGP, e - EGP, ? - incomplete Network Next Hop Metric LocPrf Weight Path >i 0.0.0.0/0 10.100.1.1 0 100 100 i i 3.0.0.0/8 10.100.1.1 0 100 100 14207 3944 6461 701 80 i i 10.100.1.2 0 100 100 14207 3944 6461 701 80 i i 10.100.1.5 0 100 100 14207 3944 6461 701 80 i
show bgp route ipv4 vpn [as-path longer count] [rd route-distinguisher] [labels]
Displays information for Border Gateway Protocol (BGP) Virtual Private Network IP Version 4 (VPN-IPv4) address prefix-based routes.
all modes
as-path longer count |
Optional. Information for AS-paths equal to or longer than the count value. The range of count values is 1 to 300. |
rd route-distinguisher |
Optional. Route information for only a specific Virtual Private Network (VPN) context with a route distinguisher of the route-distinguisher value, which can be expressed in either of the following formats:
|
labels |
Optional. Displays Multiprotocol Label Switching (MPLS) label information. |
This command displays all VPN-IPv4 routes in all VPN contexts.
Use the show bgp route ipv4 vpn command to display information for BGP VPN-IPv4 address prefix-based routes.
Use the rd route-distinguisher construct to display VPN-IPv4 prefixes for just the selected VPN context that matches the route-distinguisher argument.
The following example displays output from the show bgp route ipv4 vpn command:
[local]Redback>show bgp route ipv4 vpn
Address Family: ipv4 vpn BGP table version is 0, local router ID is 7.7.7.2 Status codes: d damped, h history, > best, i internal Origin codes: i - IGP, e - EGP, ? – incomplete VPN RD: 1.2.3.4:100 Network Next Hop Metric LocPrf Weight Path > 6.3.0.0/18 192.168.41.100 0 100 100 3944 6461 7170 1455 i VPN RD: 64001:200 Network Next Hop Metric LocPrf Weight Path > 3.0.0.0/8 192.168.3.100 0 100 100 3944 6461 701 80 i > 10.10.10.10/32 192.168.3.8 0 100 100 100 i
The following example displays only VPN-IPv4 routes from the context with route distinguisher of 1.2.3.4:100:
[local]Redback>show bgp route ipv4 vpn rd 1.2.3.4:100
Address Family: ipv4 vpn BGP table version is 0, local router ID is 7.7.7.2 Status codes: d damped, h history, > best, i internal Origin codes: i - IGP, e - EGP, ? – incomplete VPN RD: 1.2.3.4:100 Network Next Hop Metric LocPrf Weight Path > 6.3.0.0/18 192.168.41.100 0 100 100 3944 6461 7170 1455 i
The following example displays MPLS label information for VPN-IPv4 routes:
[local]Redback>show bgp route ipv4 vpn labels
VPN RD: 2:2 Network Next Hop Rcv Label Alloc Label 2.1.0.0/16 10.13.49.207 22 589830 2.3.0.0/16 10.13.49.207 21 589829 4.2.1.1/32 10.13.49.207 19 589828 VPN RD: 10.11.12.13:100 Network Next Hop Rcv Label Alloc Label 2.1.0.0/16 10.13.49.207 22 589830 2.3.0.0/16 10.13.49.207 21 589829 4.2.1.1/32 10.13.49.207 19 589828 6.3.0.0/18 192.168.41.100 nolabel 589826 VPN RD: 20.21.22.23:200 Network Next Hop Rcv Label Alloc Label 1.1.1.1/32 0.0.0.0 nolabel 589825
The following example displays MPLS label information only for VPN-IPv4 routes from the context with route distinguisher of 2:2:
[local]Redback>show bgp route ipv4 vpn rd 2:2 labels
VPN RD: 2:2 Network Next Hop Rcv Label Alloc Label 2.1.0.0/16 10.13.49.207 22 589830 2.3.0.0/16 10.13.49.207 21 589829 4.2.1.1/32 10.13.49.207 19 589828
show bgp route ipv4 vpn summary
Displays a summary report of Border Gateway Protocol (BGP) Virtual Private Network IP Version 4 (VPN-IPv4) routes in the BGP routing tables for all contexts.
all modes
This command has no keywords or arguments.
None
Use the show bgp route ipv4 vpn summary command to display a summary report of BGP VPN-IPv4 routes in the BGP routing tables for all contexts.
The following example displays output from the show bgp route ipv4 vpn summary command:
[local]Redback>show bgp route ipv4 vpn summary
Address Family: ipv4 vpn BGP router identifier: 2.2.2.2, local AS number: 64000 BGP route table version: 5065742, RIB table version: 5065742 Neighbors Configured: 1, Established: 1 Sourced paths: redistributed: 0, networked: 0, aggregated: 0 Dampening: Disabled Entry Type Count Memory Network 132281 16201112 Path 132278 3632896 Neighbor AS MsgRcvd MsgSent TblVer InQ OutQ Rst Up/Down Pfx Rcvd/Sent 1.1.1.1 64000 336115 258 5065646 0 0 0 04:06:48 132270 8 Context: 0x40080002 VPN RD: 2:2 Neighbor AS MsgRcvd MsgSent TblVer InQ OutQ Rst Up/Down Pfx Rcvd/Sent 60.1.2.2 200 251 48388 5065742 0 0 0 04:06:50 2 0 Context: 0x40080003 VPN RD: 3:3 Neighbor AS MsgRcvd MsgSent TblVer InQ OutQ Rst Up/Down Pfx Rcvd/Sent 60.1.3.2 201 250 85962 5065742 0 0 0 04:06:45 3 0
show bgp route ipv6 unicast
Displays information for Border Gateway Protocol (BGP) unicast IP Version 6 (IPv6) routes.
all modes
This command has no keywords or arguments.
None
Use the show bgp route ipv6 unicast command to display information for BGP unicast IPv6 routes.
The following example displays output from the show bgp route ipv6 unicast command:
[local]Redback>show bgp route ipv6 unicast Address Family: ipv6 unicast BGP table version is 2, local router ID is 10.12.209.174 Status codes: d damped, h history, > best, i internal Origin codes: i - IGP, e - EGP, ? - incomplete Network Next Hop Metric LocPrf Weight Path > 9001::/64 7001::ff 0 100 100 200 i > 9002::/64 7001::ff 0 100 100 200 i
show bgp route ipv6 vpn [as-path | community | ext-community | flap-statistics | inconsistent-as | labels | neighbor | rd | regexp | sourced | summary]
Displays information for Border Gateway Protocol (BGP) IP Version 6 (IPv6) VPN routes.
all modes
as-path |
Optional. Displays autonomous system (AS) path information for BGP IPv6 VPN routes. |
community |
Optional. Displays community information for BGP IPv6 VPN routes. |
ext-community |
Optional. Displays BGP IPv6 routes for IPv6 VPN route target extended communities. |
flap-statistics |
Optional. Displays BGP route-flap statistics accounting information for IPv6 routes. |
inconsistent-as |
Optional. Displays BGP IPv6 VPN routes sourced from more than one autonomous system (AS). |
labels |
Optional. Displays Multiprotocol Label Switching (MPLS) label information for BGP IPv6 VPN routes |
neighbor |
Optional. Displays information about IPv6 VPN routes to and from BGP neighbors. |
rd |
Optional. Displays route information for BGP IPv6 VPN routes that have route distinguishers. |
regexp |
Optional. Displays BGP IPv6 VPN route communities. |
sourced |
Optional. Displays BGP IPv6 VPN routes sourced from the local autonomous system (AS). |
summary |
Optional. Displays summarized information about BGP IPv6 VPN routes. |
Enter the show bgp route ipv6 vpn command without any optional arguments to display information about all BGP IPv6 VPN routes currently configured on the system.
Use the show bgp route ipv6 unicast command to display information for BGP IPv6 VPN routes.
The following example displays output from the show bgp route ipv6 vpn command:
[local]Redback>show bgp route ipv6 vpn Address Family: ipv6 vpn Address Family: ipv6 vpn BGP table version is 72484, local router ID is 100.100.100.101 Status codes: d damped, h history, > best, i internal Origin codes: i - IGP, e - EGP, ? - incomplete VPN RD: 10:2222 Network Next Hop Metric LocPrf Weight Path >i 7::/20 22.22.22.22 0 100 100 ? VPN RD: 10:3333 Network Next Hop Metric LocPrf Weight Path >i 7::/20 22.22.22.22 0 100 100 ? VPN RD: 100:101 Network Next Hop Metric LocPrf Weight Path >i 1000::/64 1.1.1.1 0 100 100 ? > 2000::/64 :: 0 100 32768 ? VPN RD: 200:1 Network Next Hop Metric LocPrf Weight Path > 1600::1:1:0/120 :: 0 100 32768 ? > 1600::2:1:0/120 :: 0 100 32768 ? > 1600::3:1:0/120 :: 0 100 32768 ? > 1600::4:1:0/120 :: 0 100 32768 ? > 1600::5:1:0/120 :: 0 100 32768 ? > 1600::6:1:0/120 :: 0 100 32768 ? > 1600::7:1:0/120 :: 0 100 32768 ? > 1600::8:1:0/120 :: 0 100 32768 ? > 1600::9:1:0/120 :: 0 100 32768 ? > 1600::10:1:0/120 :: 0 100 32768 ? > 1600::11:1:0/120 :: 0 100 32768 ? > 1600::12:1:0/120 :: 0 100 32768 ? > 1600::13:1:0/120 :: 0 100 32768 ? > 1600::14:1:0/120 :: 0 100 32768 ? > 1600::15:1:0/120 :: 0 100 32768 ? > 1600::16:1:0/120 :: 0 100 32768 ? > 1600::17:1:0/120 :: 0 100 32768 ? > 1600::18:1:0/120 :: 0 100 32768 ? > 1600::19:1:0/120 :: 0 100 32768 ? > 1600::20:1:0/120 :: 0 100 32768 ? > 1600::21:1:0/120 :: 0 100 32768 ? > 1600::22:1:0/120 :: 0 100 32768 ? > 1600::23:1:0/120 :: 0 100 32768 ? > 1600::24:1:0/120 :: 0 100 32768 ? > 1600::25:1:0/120 :: 0 100 32768 ? > 1600::26:1:0/120 :: 0 100 32768 ? > 1600::27:1:0/120 :: 0 100 32768 ? > 1600::28:1:0/120 :: 0 100 32768 ? > 1600::29:1:0/120 :: 0 100 32768 ? > 1600::30:1:0/120 :: 0 100 32768 ? > 1600::31:1:0/120 :: 0 100 32768 ? > 1600::32:1:0/120 :: 0 100 32768 ? > 1600::33:1:0/120 :: 0 100 32768 ? > 1600::34:1:0/120 :: 0 100 32768 ? > 1600::35:1:0/120 :: 0 100 32768 ? > 1600::36:1:0/120 :: 0 100 32768 ? > 1600::37:1:0/120 :: 0 100 32768 ? > 1600::38:1:0/120 :: 0 100 32768 ? > 1600::39:1:0/120 :: 0 100 32768 ? > 1600::40:1:0/120 :: 0 100 32768 ? > 1600::41:1:0/120 :: 0 100 32768 ? > 1600::42:1:0/120 :: 0 100 32768 ? > 1600::43:1:0/120 :: 0 100 32768 ? > 1600::44:1:0/120 :: 0 100 32768 ? > 1600::45:1:0/120 :: 0 100 32768 ? > 1600::46:1:0/120 :: 0 100 32768 ? > 1600::47:1:0/120 :: 0 100 32768 ? > 1600::48:1:0/120 :: 0 100 32768 ? > 1600::49:1:0/120 :: 0 100 32768 ? > 1600::50:1:0/120 :: 0 100 32768 ? > 1600::51:1:0/120 :: 0 100 32768 ? > 1600::52:1:0/120 :: 0 100 32768 ? > 1600::53:1:0/120 :: 0 100 32768 ? > 1600::54:1:0/120 :: 0 100 32768 ? > 1600::55:1:0/120 :: 0 100 32768 ? > 1600::56:1:0/120 :: 0 100 32768 ? > 1600::57:1:0/120 :: 0 100 32768 ? > 1600::58:1:0/120 :: 0 100 32768 ? > 1600::59:1:0/120 :: 0 100 32768 ? > 1600::60:1:0/120 :: 0 100 32768 ? > 1600::61:1:0/120 :: 0 100 32768 ? > 1600::62:1:0/120 :: 0 100 32768 ? > 1600::63:1:0/120 :: 0 100 32768 ? > 1600::64:1:0/120 :: 0 100 32768 ? > 1600::65:1:0/120 :: 0 100 32768 ? > 1600::66:1:0/120 :: 0 100 32768 ? ---(more)---
show bgp route labels
Displays Multiprotocol Label Switching (MPLS) labels associated with Border Gateway Protocol (BGP) routes.
all modes
This command has no keywords or arguments.
None
Use the show bgp route labels command to display MPLS labels associated with BGP routes.
The following example displays the MPLS labels associated with BGP routes in the local context:
[local]Redback>show bgp route labels
Network Next Hop Rcv Label Alloc Label 3.0.0.0/8 155.53.0.1 nolabel nolabel 155.53.0.1 nolabel nolabel 4.0.0.0/8 155.53.0.1 nolabel nolabel 6.0.0.0/20 155.53.0.1 nolabel nolabel
The following example displays the MPLS labels associated with BGP routes in a Virtual Private Network (VPN) context:
[local]Redback>show bgp route labels
VPN RD: 10.11.12.13:100 Network Next Hop Rcv Label Alloc Label 2.1.0.0/16 10.13.49.207 22 589830 2.3.0.0/16 10.13.49.207 21 589829 4.2.1.1/32 10.13.49.207 19 589828 6.3.0.0/18 192.168.41.100 nolabel 589826
show bgp route neighbor ip-addr {active | advertised | dampened | history | not-advertised | received}
Displays information about routes to and from Border Gateway Protocol (BGP) neighbors.
all modes
ip-addr |
IP address of the neighbor. |
active |
Displays only active BGP routes from the specified neighbor. |
advertised |
Displays only BGP routes advertised to the specified neighbor. |
dampened |
Displays only dampened BGP routes from the specified neighbor. |
history |
Displays a history of the BGP routes form the specified neighbor. |
not-advertised |
Displays only BGP routes not advertised to the specified neighbor. |
received |
Displays only BGP routes received from the specified neighbor. |
None
Use the show bgp route neighbor command to display information about routes to or from BGP neighbors.
The following example displays output from the show bgp route neighbor ip-addr active command:
[local]Redback>show bgp route neighbor 192.168.41.7 active
Address Family: ipv4 unicast BGP table version is 418798, local router ID is 192.168.4.100 Status codes: d damped, h history, > best, i internal Origin codes: i - IGP, e - EGP, ? - incomplete Network Next Hop Metric LocPrf Weight Path > 3.3.3.0/24 192.168.41.7 0 100 100 64173 ? > 4.4.4.0/24 192.168.41.7 0 100 100 64173 ? > 5.5.5.0/24 192.168.41.7 0 100 100 64173 ? > 8.8.8.0/24 192.168.41.7 0 100 100 64173 ? > 10.12.208.81/32 192.168.41.7 0 100 100 64173 ? > 10.13.208.81/32 192.168.41.7 0 100 100 64173 ? > 10.100.2.3/32 192.168.41.7 0 100 100 64173 ? > 155.0.0.0/8 192.168.41.7 0 100 100 64173 ? > 155.53.1.235/32 192.168.41.7 0 100 100 64173 ? > 155.53.36.0/24 192.168.41.7 0 100 100 64173 ? > 165.30.199.0/24 192.168.41.7 0 100 100 64173 14207 64513 2828 2828 2828 2828 701 i
show bgp route regexp as-path-string...
Displays Border Gateway Protocol (BGP) communities that match the specified autonomous system (AS) path string.
all modes
as-path-string... |
One or more AS path strings. |
None
Use the show bgp route regex command to display BGP routes that contain the specified AS path string.
The following example displays output from the show bgp route regex command. Only routes that contain the AS paths, 64173 and 14207, are displayed:
[local]Redback>show bgp route regex 64137 14207
Address Family: ipv4 unicast BGP table version is 418910, local router ID is 192.168.4.100 Status codes: d damped, h history, > best, i internal Origin codes: i - IGP, e - EGP, ? - incomplete Network Next Hop Metric LocPrf Weight Path 3.0.0.0/8 192.168.41.7 0 100 100 64173 14207 3944 6461 701 80 i 4.0.0.0/8 192.168.41.7 0 100 100 64173 14207 64513 2828 2828 2828 2828 1 i 4.21.132.0/23 192.168.41.7 0 100 100 64173 14207 64513 2828 2828 2828 2828 6461 16422 i 6.1.0.0/16 192.168.41.7 0 100 100 64173 14207 3944 6461 7170 1455 i 6.2.0.0/22 192.168.41.7 0 100 100 64173 14207 64513 2828 2828 2828 2828 7170 1455 i 6.3.0.0/18 192.168.41.7 0 100 100 64173 14207 3944 6461 7170 1455 i 6.4.0.0/16 192.168.41.7 0 100 100 64173 14207 3944 6461 7170 1455 i 6.5.0.0/19 192.168.41.7 0 100 100 64173 14207 3944 6461 7170 1455 i
show bgp route sourced
Displays Border Gateway Protocol (BGP) routes sourced from the local autonomous system (AS).
all modes
This command has no keywords or arguments.
None
Use the show bgp route sourced command to display BGP routes sourced from the local autonomous system.
The following snapshot from a configuration file enables the output for the show bgp route sourced command example:
router bgp 64001 address-family ipv4 unicast redistribute static ! ip route 0.0.0.0/0 10.13.49.254 ip route 10.0.0.0/8 10.13.49.254 ip route 155.0.0.0/8 10.13.49.254 ip route 155.53.36.126/32 10.13.49.254
The previous configuration provides the commands that enable the following output:
[local]Redback>show bgp route sourced
Address Family: ipv4 unicast BGP table version is 418884, local router ID is 192.168.4.100 Status codes: d damped, h history, > best, i internal Origin codes: i - IGP, e - EGP, ? - incomplete Network Next Hop Metric LocPrf Weight Path > 10.0.0.0/8 10.13.49.254 0 100 32768 ? > 155.0.0.0/8 10.13.49.254 0 100 32768 ? > 155.53.36.126/32 10.13.49.254 0 100 32768 ?
show bgp route summary
Displays a summary report of Border Gateway Protocol (BGP) routes in the BGP routing table.
all modes
This command has no keywords or arguments.
None
Use the show bgp route summary command to display a summary report of BGP routes in the BGP routing table.
The following example displays output from the show bgp route summary command:
[local]Redback>show bgp route summary
Address Family: ipv4 unicast BGP router identifier: 0.0.0.0, local AS number: 100 BGP route table version: 0, RIB table version: 0 Neighbors Configured: 4, Established: 0 Sourced paths: redistributed: 0, networked: 0, aggregated: 0 Entry Type Count Memory Network 103389 10880700 Path 393376 12588032 Neighbor AS MsgRcvd MsgSent TblVer InQ OutQ Rst Up/Down PfxRcvd/Sent 10.11.64.99 14207 0 0 0 0 0 0 1w0d Connect 10.11.64.170 64001 0 0 0 0 0 0 1w0d Idle 10.12.208.76 64001 104681 68515 247945 0 0 1 6d21h 83582 103070 10.12.208.85 64001 0 0 0 0 0 0 1w0d Connect 10.12.208.89 100 0 1461 0 0 0 0 1w0d Idle 10.12.209.136 10000 0 1428 0 0 0 0 1w0d Idle 10.13.49.122 64001 205930 48263 247945 0 0 6 5d17h 103107 103070 10.13.49.173 64173 0 0 0 0 0 0 1w0d Idle (admin) 10.13.49.174 200 0 1456 0 0 0 0 1w0d Idle 10.100.2.1 64001 0 0 0 0 0 0 1w0d Connect 10.100.2.2 64001 0 0 0 0 0 0 1w0d Connect 10.100.200.1 64001 0 0 0 0 0 0 1w0d Connect 155.53.1.235 14207 48126 14552 247945 0 0 0 1w0d 103151 19641 155.53.1.236 64513 51801 37437 247945 0 0 0 1w0d 102592 83518
show bgp summary
Displays a summary of Border Gateway Protocol (BGP) status and statistical information.
all modes
This command has no keywords or arguments.
None
Use the show bgp summary command to display a summary of BGP status and statistical information.
The following example displays output from the show bgp summary command:
[local]Redback>show bgp summary
Address Family: ipv4 unicast BGP router identifier: 10.10.10.10, local AS number: 4 BGP route table version: 0, RIB table version: 0 Neighbors Configured: 2, Established: 0 Sourced paths: redistributed: 0, networked: 0 Dampening: Disabled Entry Type Count Memory Total Alloc Network 0 24 0 Path 0 0 0 Neighbor AS MsgRcvd MsgSent TblVer InQ OutQ Up/Down PfxRcvd/Sent 10.10.2.2 5 0 0 0 0 0 03:35:19 Idle 10.10.10.1 0 0 0 0 0 0 02:08:19 Idle (noAS)
For ports on channelized OC-12 or STM-1 traffic cards, the syntax is:
show bindings [slot/port[:chan-num[:sub-chan-num] [circuit-id]]] [circuit-type] [bind-type] [counters [persistent]] [summary] [detail]
For channelized ports on DS-3 or E1 traffic cards, the syntax is:
show bindings [slot/port[:chan-num [circuit-id]]] [circuit-type] [bind-type] [counters [persistent]] [summary] [detail]
For clear-channel ports on DS-3, E3, or E1 traffic cards, or ports on Asynchronous Transfer Mode (ATM) OC, ATM DS-3, Ethernet, or Packet over SONET/SDH (POS) traffic cards, the syntax is:
show bindings [slot/port [circuit-id]] [circuit-type] [bind-type] [counters [persistent]] [summary] [detail]
Displays the configured bindings for one or more subscribers, ports, channels, or permanent virtual circuits (PVCs) on the system.
all modes
slot |
Optional. Chassis slot number for the traffic card on which the port, channel, or circuit is configured. If omitted, shows bindings for all circuits in the system. |
port |
Required when you enter the slot argument. Port number on which the channel or circuit is configured. |
chan-num |
Optional. Channel number for which bindings are displayed. If omitted, displays bindings for all channels on the specified port. The range of values depends on the type of port; see Table 4 for the range of values. |
sub-chan-num |
Optional. Subchannel number for which bindings are displayed. If omitted, displays bindings for all subchannels in the specified channel. The range of values depends on the type of port; see Table 4 for the range of values. |
circuit-id |
Optional. Circuit identifier, according to one of the constructs listed in Table 5. |
circuit-type |
Optional. Type of port, channel, or circuit for which bindings are displayed, according to one of the keywords listed in Table 6. |
bind-type |
Optional. Type of binding for which information displays, according to one of the keywords listed in Table 7. |
counters |
Optional. Displays circuit counters. |
persistent |
Optional. If omitted, displays values since the counters were last cleared or the card was last reloaded. If specified, displays values since the system was last reloaded. |
summary |
Optional. Displays only summary information for the specified PVCs. |
detail |
Optional. Displays detailed information for the specified PVCs. |
Displays all ports, channels, or circuits that are bound within the current context.
Use the show bindings command to display information on configured bindings. Use the optional keywords and arguments, listed in Table 5, to restrict the display to specific ports, channels, or PVCs of interest.
Use the slot, port, chan-num, and sub-chan-num arguments to restrict the display to include binding information only for PVCs configured on that slot, port, and channel.
The value for the port argument on the SmartEdge 100 router depends on the MIC slot in which the MIC is installed.
Table 4 lists the range of values for chan-num and sub-chan-num arguments for various types of channelized ports.
Port |
Channel Types |
chan-num Range |
sub-chan-num Range |
---|---|---|---|
Channelized OC-12 |
DS-3, DS-1 |
1 to 12 |
1 to 28 |
Channelized STM-1 |
E1, DS-0 channel group |
1 to 63 |
1 to 31 |
Channelized DS-3 |
DS-1 |
1 to 28 |
– |
Channelized E1 |
DS-0 channel group |
1 to 31 |
– |
Table 5 lists the constructs for the circuit-id argument.
Construct |
Description |
---|---|
dlci dlci |
Data-link connection identifier (DLCI) of a configured Frame Relay PVC. The range of values is 16 to 991. |
vlan-id vlan-id |
Virtual LAN (VLAN) tag value for an 802.1Q tunnel or PVC. The vlan-id argument is one of the following constructs:
The range of values for any VLAN tag value is 1 to 4095. |
vpi-vci vpi vci |
Virtual path identifier (VPI) and virtual circuit identifier (VCI) of a configured ATM PVC. The range of values is 0 to 255 for the VPI and 1 to 65535 for the VCI. |
You can further restrict the display to a specific PVC:
Use the circuit-type argument to restrict the displayed information to the specified type of circuit; Table 6 lists the keywords for the circuit-type argument.
Keyword |
Circuit Type |
---|---|
atm |
Asynchronous Transfer Mode (ATM) PVCs |
chdlc |
Ports or channels with Cisco High-Level Data Link Control (HDLC) encapsulation |
clips |
Ethernet ports with clientless IP service selection (CLIPS) PVCs |
dot1q |
802.1Q PVCs |
ether |
Ethernet ports |
fr |
Frame Relay PVCs |
gre |
Generic Routing Encapsulation (GRE) tunnel circuits |
mpls |
Multiprotocol label switching (MPLS) circuits |
ppp |
Point-to Point Protocol (PPP) encapsulated circuits |
pppoe |
PPP over Ethernet (PPPoE) encapsulated circuits |
Use the bind-type argument to restrict the displayed information to the specified type of binding.
Table 7 lists the keywords for the bind-type argument.
Keyword |
Circuit Type |
---|---|
auth |
PVCs bound using the Password Authentication Protocol (PAP) or the Challenge Handshake Authentication Protocol (CHAP). |
bound |
Bound PVCs. |
unbound |
Unbound PVCs. |
interface |
PVCs bound to an interface. |
no-bind |
PVCs that have no bindings. |
subscriber |
PVCs bound to interfaces through subscriber records. |
The keywords for the bind-type argument limit the display of bindings as follows:
Use the counters keyword to display packet bytes sent and received for the displayed circuits.
Use the persistent keyword to display the counters with values accumulated since the system was last reloaded.
Use the summary keyword to display only the summary that normally appears at the end of the display.
Use the detail keyword to display additional information about the displayed circuits.
The following example displays all bindings in the current context (local):
[local]Redback>show bindings
Circuit State Encaps Bind Type Bind Name 1/1 Up cisco-hdlc interface toTokyo@London 1/2 Up cisco-hdlc interface toLondon@Tokyo 1/3 Up cisco-hdlc interface toLA1@NYC1 1/4 Up cisco-hdlc interface toNYC1@LA1 2/1:5 Up cisco-hdlc interface toNYC2@London 2/1:6 Up cisco-hdlc interface toNYC1@London 2/1:7 Up cisco-hdlc interface toLA1@Tokyo 2/1:8 Up cisco-hdlc interface toLA2@Tokyo 2/1 Up cisco-hdlc 2/2:5 Up cisco-hdlc interface toLondon@NYC2 2/2:6 Up cisco-hdlc interface toLondon@NYC1 2/2:7 Up cisco-hdlc interface toTokyo@LA1 2/2:8 Up cisco-hdlc interface toTokyo@LA2 2/2:15 Up cisco-hdlc 2/2:16 Up cisco-hdlc 2/2 Up cisco-hdlc 5/1 Down ethernet 6/1:1 vpi-vci 1 101 Down bridge1483 interface internal@London 6/1:1 vpi-vci 1 102 Down bridge1483 interface internal@Tokyo 6/1:1 vpi-vci 4 4 Down multi1483 6/1:1 vpi-vci 44 45 Down multi1483 6/1:1 vpi-vci 55 66 Down multi1483 7/1 Up ethernet interface adm@local 10/1:1 Down frame-relay 10/1:1 dlci 0 Down frame-relay 10/1:1 dlci 1023 Down frame-relay 10/1:1 dlci 16 Down frame-relay 10/1:3 Down cisco-hdlc 11/1 Down cisco-hdlc 12/1 Down ethernet interface toNYC1@NYC2 12/1 vlan-id 1 Down dot1q multi 12/2 Down ethernet interface toNYC2@NYC1 12/3 Down ethernet interface toLA2@LA1 12/4 Down ethernet interface toLA1@LA2 GRE 1.2.3.4 key 1 Down gre Link share ethernet Down ethernet Summary: total: 38 up: 19 down: 19 bound: 19 unbound: 19 no-bind: 19 auth: 0 interface: 19 subscriber: 0 atm: 5 chdlc: 20 dot1q: 1 ether: 7 fr: 4 gre: 1 mpls: 0 ppp: 0 pppoe: 0 clips: 0
The following example displays binding information for all PVCs configured with the bind interface command for port 1 on the card in slot 2:
[local]Redback(config-ctx)#show bindings 2/1 interface
Circuit State Encaps Bind Type Bind Name 2/1:5 Up cisco-hdlc interface toNYC2@London 2/1:6 Up cisco-hdlc interface toNYC1@London 2/1:7 Up cisco-hdlc interface toLA1@Tokyo 2/1:8 Up cisco-hdlc interface toLA2@Tokyo Summary: total: 4 up: 4 down: 0 bound: 4 unbound: 0 no-bind: 0 auth: 0 interface: 4 subscriber: 0 atm: 0 chdlc: 4 dot1q: 0 ether: 0 fr: 0 gre: 0 mpls: 0 ppp: 0 pppoe: 0 clips: 0
The following example displays all bindings for all Frame Relay PVCs for port 1 on the card in slot 10:
[local]Redback(config-ctx)#show bindings 10/1 fr
Circuit State Encaps Bind Type Bind Name 10/1:1 Down frame-relay 10/1:1 dlci 0 Down frame-relay 10/1:1 dlci 1023 Down frame-relay 10/1:1 dlci 16 Down frame-relay Summary: total: 4 up: 0 down: 4 bound: 0 unbound: 4 no-bind: 4 auth: 0 interface: 0 subscriber: 0 atm: 0 chdlc: 0 dot1q: 0 ether: 0 fr: 4 gre: 0 mpls: 0 ppp: 0 pppoe: 0 clips: 0
show bridge associations {bridge-name ctx-name [detail] | all [detail] | circuit slot/port [circuit-id]}
Displays bridge profile permanent virtual circuit (PVC) assignments.
bridge-name |
Name of the bridge with associations to be displayed. |
ctx-name |
Name of the context in which the bridge exists with associations to be displayed. |
detail |
Optional. Displays detailed information. |
all |
Displays the bridge forwarding table for all bridges in all contexts. |
circuit |
Displays the bridge forwarding table for the specified bridged port or PVC. |
slot |
Chassis slot number of the traffic card with the bridged port or PVC. |
port |
Port number of the bridged port or the port with the bridged PVC. |
circuit-id |
Optional. Bridged PVC identifier, according to one of the constructs listed in Table 8. |
Displays associations for all bridges in the current context.
Use the show bridge associations command to display bridge profile PVC assignments.
Caution! | ||
Risk of performance loss. Enabling the generation of debug messages
can severely affect system performance. To reduce the risk, exercise
caution before enabling the generation of any debug messages on a
production system.
|
Use the circuit slot/portcircuit-id construct to display the association for that bridged PVC.
Table 8 lists the values for the circuit-id argument.
Field |
Field |
---|---|
vlan vlan-id |
A filter that limits the command to a specified virtual LAN (VLAN) 802.1Q tunnel or PVC. The vlan-id argument is one of the following constructs:
The range of values for any VLAN tag value is 1 to 4095. |
vpi-vci vpi vci |
Virtual path identifier (VPI) and virtual circuit identifier (VCI) for an Asynchronous Transfer Mode (ATM) permanent virtual circuit (PVC). The range of values is 0 to 255 and 1 to 65535, respectively. |
Use the all keyword to display associations for all bridges in all contexts.
The following example displays associations for all bridges:
[local]Redback#show bridge associations all
Bridge Profile Circuit trib 3/1 trunk 3/2
show bridge bindings {bridge-name ctx-name [detail] | all [detail] | circuit slot/port [circuit-id]}
Displays bridge binding information for one or more bridges or for a bridged permanent virtual circuit (PVC).
bridge-name |
Name of the bridge with binding information to be displayed. |
ctx-name |
Name of the context in which the bridge exists. |
detail |
Optional. Displays detailed information. |
all |
Displays the bridge forwarding table for all bridges in all contexts. |
circuit |
Displays the bridge forwarding table for the specified bridged port or PVC. |
slot |
Chassis slot number of the traffic card with the bridged port or PVC. |
port |
Port number of the bridged port or the port with the bridged PVC. |
circuit-id |
Optional. Bridged PVC identifier, according to one of the constructs listed in Table 9. |
Displays bindings for all bridges in the current context.
Use the show bridge bindings command to display bridge binding information for one or more bridges or for a bridged PVC.
Use the circuit slot/port circuit-id construct to display the binding for that bridged PVC.
Table 9 lists the values for the circuit-id argument.
Field |
Field |
---|---|
vlan vlan-id |
A filter that limits the command to a specified virtual LAN (VLAN) 802.1Q tunnel or PVC. The vlan-id argument is one of the following constructs:
The range of values for any VLAN tag value is 1 to 4095. |
vpi-vci vpi vci |
Virtual path identifier (VPI) and virtual circuit identifier (VCI) for an Asynchronous Transfer Mode (ATM) PVC. The range of values is 0 to 255 and 1 to 65535, respectively. |
Use the all keyword to display bindings for all bridges in all contexts.
The following example displays detailed binding information for all bridges:
[local]Redback#show bridge bindings all detail
Flags are,(L)earning,(D)ynamic,(t)ributary,(T)runk, (R)estricted,(d)eleted,(S)tale,(l)og,(U)p Context Bridge Group Circuit Flag c1 b1 3/1 L-t---lU c1 b2 3/2 L-T----U c1 b3 3/3 L-t----- c1 b4 3/4 L-t-----
show bridge info {bridge-name ctx-name [detail] | all [detail]}
Displays information for configured bridges.
bridge-name |
Name of the bridge with information to be displayed. |
ctx-name |
Name of the context in which the bridge exists. |
detail |
Optional. Displays detailed information. |
all |
Displays information for bridges in all contexts. |
Displays bridge information for all bridges in the current context.
Use the show bridge info command to display information for configured bridges.
Use the all keyword to display information for all bridges in all contexts.
The following example displays information for all bridges:
[local]Redback#show bridge info all Type can be: (L)earning,(D)ynamic,(R)outing Context Bridge Group Type Ccts Aging MAC D-MAC Description c1 b1 L-- 1 300 6 3 Bridge one c1 b2 L-- 1 300 1 0 Bridge two c1 b3 L-- 1 300 0 0 Bridge three c1 b4 L-- 1 300 0 0 Bridge four
The following example illustrates the show bridge command with the info keyword. The bridge name is red and the context name is ink. In this example information is provided on loop-detection using the MAC moves method:
[local]Redback(config-bridge)#show bridge info lbdl ink Type can be: (L)earning,(R)outing,(Md) MacMove Drop Context Bridge Group Type Ccts Aging MAC D-MAC PW-Ccts Description ink lbdl L-- 0 300 0 0 0
show bridge loop-detection bridge-name context-name
Shows the MAC moves loop detection status of the specified bridge.
exec
bridge-name |
Name of the bridge. |
context-name |
Name of the context that contains the bridge. |
Use the show bridge loop-detection command to the MAC moves loop detection status of the specified bridge.
The following example illustrates the show bridge command with the loop-detection keyword. The bridge name is lbdl and the context name is ink:
[local]Redback(config-bridge)#show bridge loop-detect lbdl ink Context Bridge Group Block-Time Interval Move-Freq Move Count ink lbdl 60 5 0 0 Circuit State Priority From Moves To Moves Retry(s) CurRetry Unknown circuit Up 0 0 0 0 0
show bridge profile [prof-name] [all]
Displays information for configured bridge profiles.
prof-name |
Optional. Name of the bridge profile with information to be displayed. |
all |
Optional. Displays information for bridge profiles in all contexts. |
Displays bridge profile information for all bridge profiles in the current context.
Use the show bridge profile command to display information for configured bridge profiles.
Use the all keyword to display information for all bridge profiles in all contexts.
The following example displays information for all bridge profiles:
[local]Redback#show bridge profile all
Flags are: (R)estricted,(t)ributary,(T)runk Profile Flag Circuits pbr Rt 0 pbu -t 5 pkr RT 0 pku -T 8
show bridge statistics {bridge-name ctx-name | all}
Displays statistics for one or more configured bridges.
bridge-name |
Name of the bridge with statistics to be displayed. |
ctx-name |
Name of the context in which the bridge exists. |
all |
Displays statistics for all bridges in all contexts. |
Displays statistics for all bridges in the current context.
Use the show bridge statistics command to display statistics for one or more configured bridges. Table 10 lists the fields that are displayed for each bridge.
Field |
Field |
---|---|
Context |
Context in which the bridge is configured. |
Bridge Group |
Name of the bridge. |
Static MAC |
Number of static medium access control (MAC) addresses configured (using the bridge mac-entry command in dot1q PVC, ATM PVC, or port configuration mode) for each bridged 802.1Q PVC, ATM PVC, or Ethernet port in this bridge. |
Drop MAC |
Number of MAC addresses specified as dropped (using the mac-entry command (in bridge configuration mode). |
Dynamic MAC |
Number of MAC addresses learned by the bridge. |
MCAST |
Number of multicast or broadcast MAC addresses. |
Station Move |
Number of station moves that have occurred on the circuits for this bridge. |
S Move Reject |
Number of station moves rejected for this bridge because of either of the following conditions:
|
The following example displays statistics for all bridges:
[local]Redback#show bridge statistics all
Context Bridge Group Static Drop Dynamic MCAST Station S Move MAC MAC MAC Move Reject c1 b1 0 0 51 0 0 0 c1 b2 0 0 51 0 0 0 c2 b3 0 0 55 0 0 0
The following example displays statistics for a specific bridge:
[local]Redback#show bridge statistics b1 c1 Context Bridge Group Static Drop Dynamic MCAST Station S Move MAC MAC MAC Move Reject c1 b1 0 0 51 0 0 0
show bridge table {bridge-name ctx-name [detail] | all [detail] | circuit slot/port [circuit-id]}
Displays the bridge forwarding table for one or more bridges or for a bridged permanent virtual circuit (PVC).
bridge-name |
Name of the bridge with the bridge forwarding table to be displayed. |
ctx-name |
Name of the context in which the bridge exists. |
detail |
Optional. Displays detailed information from the bridge forwarding table. |
all |
Displays the bridge forwarding table for all bridges in all contexts. |
circuit |
Displays the bridge forwarding table for the specified bridged port or PVC. |
slot |
Chassis slot number of the traffic card with the bridged port or PVC. |
port |
Port number of the bridged port or the port with the bridged PVC. |
circuit-id |
Optional. Bridged PVC identifier, according to one of the constructs listed in Table 11. |
None
Use the show bridge table command to display the bridge forwarding table for one or more bridges or for a bridged PVC.
Use the circuit slot/port circuit-id construct to display all bridge forwarding entries for that circuit.
Table 11 lists the values for the circuit-id argument.
Field |
Field |
---|---|
vlan vlan-id |
A filter that limits the command to a specified virtual LAN (VLAN) 802.1Q tunnel or PVC. The vlan-id argument is one of the following constructs:
The range of values for any VLAN tag value is 1 to 4095. |
vpi-vci vpi vci |
Virtual path identifier (VPI) and virtual circuit identifier (VCI) for an Asynchronous Transfer Mode (ATM) PVC. The range of values is 0 to 255 and 1 to 65535, respectively. |
Use the all keyword to display the bridge forwarding tables for all bridges in all contexts.
Table 12 lists the fields that are displayed for each bridge; some fields are displayed only when the detail keyword is specified.
Field |
Field |
---|---|
Context |
Context in which the bridge is configured. |
Bridge Group |
Name of the bridge. |
MAC |
MAC address of any type, as indicated by the Flag field. |
Circuit |
Slot, port, circuit identifier (VLAN tag value) on which the MAC address appears. |
Slot |
Displayed with the detail keyword only. |
Flag |
Displayed with the detail keyword only. Describes the MAC address or circuit, according to one or more of the following conditions:
|
Static MAC |
Displayed with the detail keyword only. Number of static MAC addresses configured (using the bridge mac-entry command in dot1q PVC, ATM PVC, or port configuration mode) for each bridged 802.1Q PVC, ATM PVC, or Ethernet portfor all bridges that are displayed. |
Drop MAC |
Displayed with the detail keyword only. Number of MAC addresses specified as dropped (using the mac-entry command (in bridge configuration mode) for all bridges that are displayed. |
Dynamic MAC |
Displayed with the detail keyword only. Number of MAC addresses learned by the bridges that are displayed. |
MCAST |
Displayed with the detail keyword only. Number of multicast or broadcast MAC addresses for all bridges that are displayed. |
The following example displays the bridge forwarding table for a specific bridge:
[local]Redback>show bridge table b1 c1
Context Bridge Group MAC Circuit c1 b1 00:00:0c:47:00:f8 3/1 vlan-id 5 c1 b1 00:00:0c:5c:df:29 3/1 vlan-id 5 c1 b1 00:01:02:78:01:35 3/1 vlan-id 5 C1 b1 00:01:02:e8:f0:45 3/1 vlan-id 5 c1 b1 00:01:03:67:f3:c0 3/1 vlan-id 5 c1 b1 00:02:3b:01:71:1d 3/1 vlan-id 5 c1 b1 00:02:3b:01:79:14 3/1 vlan-id 5 c1 b1 00:02:3b:01:79:15 3/1 vlan-id 5 C1 b1 00:02:3b:01:81:d6 3/1 vlan-id 5
The following example displays the detailed output with the summary data for the same bridge:
[local]Redback>show bridge table b1 c1 detail
Flags:(U)nbound,(D)rop,(S)tatic,(d)uplicate,(T)runk,(t)rib,(I)gnore,(i)nvalid Context Bridge Group MAC Circuit Slot Flag c1 b1 00:00:0c:47:00:f8 3/1 vlan-id 5 c ---T--- c1 b1 00:00:0c:5c:df:29 3/1 vlan-id 5 c ---T--- c1 b1 00:01:02:78:01:35 3/1 vlan-id 5 c ---T--- c1 b1 00:01:02:e8:f0:45 3/1 vlan-id 5 c ---T--- c1 b1 00:01:03:67:f3:c0 3/1 vlan-id 5 c ---T--- c1 b1 00:02:3b:01:71:1d 3/1 vlan-id 5 c ---T--- c1 b1 00:02:3b:01:79:14 3/1 vlan-id 5 c ---T--- c1 b1 00:30:88:00:01:1b 3/1 vlan-id 5 c ---T--- c1 b1 00:30:88:00:05:cc 3/1 vlan-id 5 c ---T--- c1 b1 00:30:88:00:0b:2a 3/1 vlan-id 5 c ---T--- c1 b1 00:30:88:00:0b:2d 3/1 vlan-id 5 c ---T--- c1 b1 00:30:88:00:0b:52 3/1 vlan-id 5 c ---T--- c1 b1 00:40:9d:21:fd:67 3/1 vlan-id 5 c ---T--- c1 b1 00:40:9d:22:39:01 3/1 vlan-id 5 c ---T--- c1 b1 00:50:04:07:a8:9a 3/1 vlan-id 5 c ---T--- c1 b1 00:50:04:70:b9:e6 3/1 vlan-id 5 c ---T--- c1 b1 00:50:04:73:30:2e 3/1 vlan-id 5 c ---T--- c1 b1 00:50:04:c6:61:bc 3/1 vlan-id 5 c ---T--- c1 b1 00:50:04:c9:f4:a2 3/1 vlan-id 5 c ---T--- c1 b1 00:50:da:b6:62:b3 3/1 vlan-id 5 c ---T--- c1 b1 00:80:d4:00:11:2d 3/1 vlan-id 5 c ---T--- c1 b1 00:a0:cc:59:86:ab 3/1 vlan-id 5 c ---T--- c1 b1 00:c0:b7:a3:40:da 3/1 vlan-id 5 c ---T--- c1 b1 00:d0:b7:09:e6:f9 3/1 vlan-id 5 c ---T--- c1 b1 00:d0:b7:09:e9:07 3/1 vlan-id 5 c ---T--- Static MAC = 0, Dynamic MAC = 25, Drop MAC = 0, Multicast = 0
show bridge table mac-entry mac-addr {all | bridge bridge-name ctx-name}
Displays the bridge forwarding table for one or more bridges that know the specified medium access control (MAC) address.
mac-addr |
MAC address for which the bridge forwarding table is to be displayed, in the format hh:hh:hh:hh:hh:hh. |
all |
Displays the bridge forwarding table for all bridges in all contexts that know the specified MAC address. |
bridge |
Displays the bridge forwarding table for the specified bridge. |
bridge-name |
Name of the bridge with the bridge forwarding table to be displayed. |
ctx-name |
Name of the context in which the bridge exists. |
None
Use the show bridge table mac-entry command to display the bridge forwarding table for one or more bridges that know the specified MAC address.
Use the show bridge bridge-name ctx-name construct to display the bridge forwarding table for that bridge.
Use the all keyword to display the bridge forwarding tables for all bridges in all contexts that know the specified MAC address.
The following example displays the bridge forwarding table for the bridges that know the MAC address, 00:50:04:73:30:2e:
[local]Redback>show bridge table mac-entry 00:50:04:73:30:2e
Context Bridge Group MAC Circuit c1 b2 00:50:04:73:30:2e 2/6 vpi-vci 1 33 c2 b3 00:50:04:73:30:2e 4/9 Static MAC = 0, Dynamic MAC = 2, Drop MAC = 0, Multicast = 0
show bridge table type [bridge bridge-name ctx-name [detail] | all [detail] | entry-type [detail]]
Displays the bridge forwarding table for one or more bridges.
bridge |
Optional. Displays the bridge forwarding table for the specified bridge. |
bridge-name |
Name of the bridge with the bridge forwarding table to be displayed. |
ctx-name |
Name of the context in which the bridge exists. |
detail |
Optional. Displays detailed information from the bridge forwarding table. |
all |
Optional. Displays the bridge forwarding table for all bridges in all contexts. |
entry-type |
Optional. Type of medium access control (MAC) address entry in the bridge forwarding table to be displayed, according to one or more of the following keywords:
|
Displays all types of MAC addresses for all bridge forwarding tables in the current context.
Use the show bridge table type command to display the bridge forwarding table for one or more bridges.
Use the detail keyword to display additional information.
Use the all keyword to display the bridge forwarding tables for all bridges in all contexts.
You can enter one or more keywords for the entry-type argument.
Table 13 lists the fields that are displayed for each bridge; some fields are displayed only when the detail keyword is specified.
Field |
Field |
---|---|
Context |
Context in which the bridge is configured. |
Bridge Group |
Name of the bridge. |
MAC |
MAC address of the type specified. |
Circuit |
Slot, port, circuit identifier (VLAN tag value) on which the MAC address appears. |
Slot |
Displayed with the detail keyword only. |
Flag |
Displayed with the detail keyword only. Describes the MAC address or circuit, according to one or more of the following conditions:
|
The following example displays the bridge forwarding table entries for tributary, trunk, dropped, and static MAC addresses:
[local]Redback#show bridge table type trib trunk drop static detail
Flags:(U)nbound,(D)rop,(S)tatic,(d)uplicate,(T)runk,(t)rib,(I)gnore,(i)nvalid Context Bridge Group MAC Circuit Slot Flag c1 b1 00:00:00:00:00:31 All circuits DS----- c1 b1 00:00:00:00:00:32 All circuits DS----- c1 b1 00:00:00:00:01:31 3/1 ---t--- c1 b1 00:00:00:00:01:32 3/1 ---t---
show bulkstats policy {blkst_policy | ALL} [collection]
Displays the bulk statistics (bulkstats) configuration information and data transfer statistics, or the contents of the current collection file that have not yet been successfully transferred to the receiver, for the specified bulkstats policy or for all policies.
all modes
policy blkst_policy |
Name of the bulkstats policy for which bulkstats configuration information and statistics are to be displayed. |
policy ALL |
Specifies that bulkstats configuration information and statistics are to be displayed for all policies. |
collection |
Optional. Specifies that the contents of the collection file for the specified policy in its current state is to be displayed, rather than the configuration. |
Displays bulkstats configuration information for the specified policy.
Use the show bulkstats command to display the current bulkstats configuration information and statistics about the data transfer for the specified policy or for all policies, including:
Use the optional collection keyword to display the contents of the current bulkstats collection file. This can be useful in debugging schema definitions.
The following example displays bulk statistics information:
[local]Redback>show bulkstats policy bulk
Primary receiver: 198.168.145.99 via ftp Secondary receiver: 198.168.147.31 via ftp Last successful transfer to 198.168.145.99 on WED JUN 29 14:55:03 2005 Transferred 1019 bytes into "//snmp:30A8E9F5A5BD154@198.168.145.99/Bulkstats/whitney_161953" Last transfer attempt: WED JUN 29 14:58:47 2005 Next transfer attempt: FRI JUL 01 09:06:58 2005
The following example displays the current collection file:
[local]Redback>show bulkstats policy bulk collection
enet0: (454) 0/0 (null) 4632 2a 36 1 atm50: (454) 5/0 (null) 0 0 0 0 atm51: (454) 5/1 (null) 0 0 0 0
show bypass [group group-name] [summary] [down | up] [lg group-name | lg id id-num] [port-cir] [detail]
Displays bypass information for one or more cross-connected circuits in the system.
all modes
group group-name |
Optional. Displays information for only the specified cross-connect group. |
summary |
Optional. Displays summary information for all circuits. |
down |
Optional. Displays information for only inactive circuits. |
up |
Optional. Displays information for only active circuits. |
port-cir |
Optional. Provides the port, slot, and circuit identifier arguments for cross-connected circuits and cross-connected link groups:
|
lg group-name |
Optional. Specifies the name of an access link group. |
lg id id-num |
Optional. Specifies the ID of an access link group. |
slot |
Optional. Chassis slot number of a card with the port for which bypass information is displayed. If omitted, displays bypass information for all cross-connected circuits in the system. |
port |
Optional. Card port number of the port for which bypass information is displayed. If omitted, displays bypass information for all cross-connected circuits on the ports of the specified card. |
circuit-id |
Optional. Circuit identifier, according to one of the constructs listed in Table 14. If omitted, displays bypass information for all circuits on the specified port or link group. |
child-circuit-type |
Optional. Child circuit type, according to one of the following keywords:
If omitted, displays bypass information for all cross-connected child circuits on the specified circuit. |
detail |
Optional. Displays detailed information. |
Displays bypass information for all cross-connected circuits on all cards.
Use the show bypass command to display bypass information for one or more cross-connected circuits in the system.
Table 14 lists the values for the circuit-id argument.
Field |
Field |
---|---|
vlan vlan-id |
A filter that limits the command to a specified virtual LAN (VLAN) 802.1Q tunnel or PVC. The vlan-id argument is one of the following constructs:
The range of values for any VLAN tag value is 1 to 4095. |
vpi-vci vpi vci |
Virtual path identifier (VPI) and virtual circuit identifier (VCI) for an Asynchronous Transfer Mode (ATM) permanent virtual circuit (PVC). The range of values is 0 to 255 and 1 to 65535, respectively. |
If you specify the VLAN tag value for an 802.1Q tunnel, the output includes bypass information for all the PVCs within the tunnel.
The following example displays bypass information for all cross-connected multiprotocol circuits that are active:
[local]Redback>show bypass up
Circuit State XC Circuit State 2/1 vpi-vci 0 34 pppoe Up 2/2 vpi-vci 0 34 pppoe Up
The following example displays cross-connect group information:
[local]Redback>show bypass group one
Circuit State XC Circuit State 4/1 vlan-id 32 Up 5/1 vpi-vci 1 32 Up
The following example displays bypass summary information:
[local]Redback>show bypass summary
Endpoints total: 5, Up: 3, Down: 2 Crossconnects total: 2, Up: 1, Down: 1