COMMAND DESCRIPTION     19/190 82-CRA 119 1170/1-V1 Uen A    

Commands: show d through show f

© Copyright Ericsson AB 2009. All rights reserved.

Disclaimer

No part of this document may be reproduced in any form without the written permission of the copyright owner. The contents of this document are subject to revision without notice due to continued progress in methodology, design and manufacturing. Ericsson shall have no liability for any error or damage of any kind resulting from the use of this document.

Trademark List

SmartEdge is a registered trademark of Telefonaktiebolaget L M Ericsson

Contents

1Command Descriptions
1.1show debug circuit
1.2show debugging
1.3show destination card
1.4show dhcp relay hosts
1.5show dhcp relay server
1.6show dhcp relay stats
1.7show dhcp relay summary
1.8show dhcp server
1.9show dhcp server file
1.10show dhcp server option-82
1.11show dhcp server range
1.12show dhcp server stats
1.13show dhcp server threshold
1.14show diag
1.15show disk
1.16show disk sse
1.17show disk sse counters
1.18show dot1q counters
1.19show dot1q profile
1.20show dot1q pvc
1.21show dot1q pvc transport
1.22show dvsr
1.23show ethernet-cfm circuit
1.24show ethernet-cfm database (domain)
1.25show ethernet-cfm database (instance-name)
1.26show ethernet-cfm database (ma)
1.27show ethernet-cfm database (mep)
1.28show ethernet-cfm database (mip)
1.29show ethernet-cfm database (rmep)
1.30show ext-community-list
1.31show flow admission-control profile
1.32show flow circuit
1.33show flow collector
1.34show flow counters
1.35show flow ip
1.36show flow ip application-list
1.37show flow ip cache
1.38show flow ip circuit
1.39show flow ip log ism
1.40show flow ip profile
1.41show flow log
1.42show flow ppa log circuit
1.43show flow ppa state
1.44show flow ppa summary
1.45show forward policy
1.46show frame-relay
1.47show frame-relay counters
1.48show frame-relay lmi-config
1.49show frame-relay lmi-errors
1.50show frame-relay lmi-stats
1.51show frame-relay profile
1.52show frame-relay pvc


1   Command Descriptions

Commands starting with “show d” through commands starting with “show f” are included.

1.1   show debug circuit

show debug circuit

1.1.1   Purpose

Displays a list of circuits for which the generation of debug messages has been enabled.

1.1.2   Command Mode

1.1.3   Syntax Description

This command has no keywords or arguments.

1.1.4   Default

None

1.1.5   Usage Guidelines

Use the show debug circuit command to display a list of circuits for which the generation of debug messages has been enabled. The circuits are listed in the order in which the debug circuit commands (in exec mode) were entered.

Note:  
By default, most show commands (in any mode) display information for the current context only or, depending on the command syntax, for all contexts. If you are an administrator for the local context, you can insert the optional context ctx-name construct, preceding the show command, to view output for the specified context without entering that context. For more information about using the context ctx-name construct, see the context command description.

Note:  
By appending a space followed by the pipe ( | ) character at the end of a show command, you can filter the output using a set of modifier keywords and arguments. For more information, see “Modifying Output of show Commands” in Using the CLI.

1.1.6   Examples

The following example shows how to enable the generation of debug messages for the following circuits: (1) a Virtual LAN (VLAN) 100 in VLAN tunnel 1 on port 3 on the Gigabit Ethernet traffic card in slot 14, and (2) a DS-1 channel 1 on port 1 on the channelized DS-3 traffic card in slot 2.

It then displays the list of circuits that have the generation of debug messages enabled:

[local]Redback#debug circuit 14/3 vlan-id 1:100
[local]Redback#debug circuit 2/1:1 
[local]Redback#show debug circuit
Circuit debugging:
14/3:1023:63/1/2/160
2/1:1:63/15/3/16777215

1.2   show debugging

show debugging

1.2.1   Purpose

Displays the debugging options that are currently enabled.

1.2.2   Command Mode

all modes

1.2.3   Syntax Description

This command has no keywords or arguments.

1.2.4   Default

None

1.2.5   Usage Guidelines

Use the show debugging command to display the debugging options that are currently enabled.

Note:  
By default, most show commands (in any mode) display information for the current context only or, depending on the command syntax, for all contexts. If you are an administrator for the local context, you can insert the optional context ctx-name construct, preceding the show command, to view output for the specified context without entering that context. For more information about using the context ctx-name construct, see the context command description.

Note:  
By appending a space followed by the pipe ( | ) character at the end of a show command, you can filter the output using a set of modifier keywords and arguments. For more information, see “Modifying Output of show Commands” in Using the CLI.

1.2.6   Examples

The following example displays output from the show debugging command for the debugging options that have been enabled:

[local]Redback>show debugging
ARP:Redback

   All debugging bits are turned on

RPL :

   ipv6 access-list debugging is turned on

1.3   show destination card

show destination card ip-addr

1.3.1   Purpose

Displays the chassis slot number of the active traffic card to which outbound packets with the specified IP address are dispatched for Forwarding Information Base (FIB) lookup.

1.3.2   Command Mode

all modes

1.3.3   Syntax Description

ip-addr

IP address of the traffic destination.

1.3.4   Default

This command has no default.

1.3.5   Usage Guidelines

Use the show destination card command to display the chassis slot number of the active traffic card to which outbound packets with the specified IP address are dispatched for FIB lookup.

To reduce the size of the FIB table in the active controller card, all outbound traffic packets that are not to be transmitted on the Ethernet management port (on the active controller card) are off-loaded to the active traffic cards in the SmartEdge® router for FIB lookup. A destination card is not configurable; instead, the controller card load balances the work by selecting a destination card based on the destination IP address in a packet.

The traffic card selected by the active controller performs the FIB lookup to locate the traffic card that actually transmits the packet and then dispatches the packet to that traffic card for output processing. If insufficient information exists to select a destination card for an IP packet (for example, Intermediate System-to-Intermediate System [IS-IS] or Open Shortest Path First [OSPF] control packets sent directly on to a Generic Routing Encapsulation [GRE] tunnel), the packet is sent to the default traffic card. To determine the default traffic card, enter the show chassis command (in any mode). The default traffic card displays a “D” in the “Flags” field.

Note:  
This command always displays a slot number unless no active traffic cards exist. If the resolution of the IP address is the Ethernet management port, the output might still display a slot number.

Note:  
By default, most show commands (in any mode) display information for the current context only or, depending on the command syntax, for all contexts. If you are an administrator for the local context, you can insert the optional context ctx-name construct, preceding the show command, to view output for the specified context without entering that context. For more information about using the context ctx-name construct, see the context command description.

Note:  
By appending a space followed by the pipe ( | ) character at the end of a show command, you can filter the output using a set of modifier keywords and arguments. For more information, see “Modifying Output of show Commands” in Using the CLI.

1.3.6   Examples

The following example displays the destination traffic card for the IP address, 10.13.49.165:

[local]Redback>show destination card 10.13.49.165
Destination address 10.13.49.165 will be dispatched to slot 10.
(2nd active card from left, out of a total 2 active cards.

If the destination address, 10.13.49.165, is not resolved to the Ethernet management port, all packets with that IP address are dispatched to the active traffic card in slot 10 for FIB lookup.

1.4   show dhcp relay hosts

show dhcp relay hosts [{duplicate-mac | ip-addr | mac-addr}] [detail]

1.4.1   Purpose

Displays Dynamic Configuration Host Protocol (DHCP) relay hosts.

1.4.2   Command Mode

all modes

1.4.3   Syntax Description

duplicate-mac

Optional. Displays information for all DHCP relay hosts with duplicate medium access control (MAC) addresses for the current context.

ip-addr

Optional. Displays the IP address (in the form A.B.C.D) of the DHCP relay host.

mac-addr

Optional. Displays the medium access control (MAC) address (in the form hh:hh:hh:hh:hh:hh) of the DHCP relay host.

detail

Optional. Displays more detailed information about the DHCP relay hosts.

1.4.4   Default

None

1.4.5   Usage Guidelines

Use the show dhcp relay hosts command to display DHCP relay hosts.

Use the ip-addr or mac-addr argument to display information only for a specific DHCP relay host. Use the duplicate-mac keyword to display information for all DHCP relay hosts with duplicate MAC addresses for the current context.

DHCP, in both proxy and relay modes, maintains host entries only for multibind interfaces, and this command displays information only for those entries.

Note:  
By default, most show commands (in any mode) display information for the current context only or, depending on the command syntax, for all contexts. If you are an administrator for the local context, you can insert the optional context ctx-name construct, preceding the show command, to view output for the specified context without entering that context. For more information about using the context ctx-name construct, see the context command description.

Note:  
By appending a space followed by the pipe ( | ) character at the end of a show command, you can filter the output using a set of modifier keywords and arguments. For more information, see “Modifying Output of show Commands” in Using the CLI.

1.4.6   Examples

The following example shows how to display DHCP relay host information:

[local]Redback>show dhcp relay hosts
Circuit                 Host Address   Hardware Address    Lease
Timestamp               DHCP_Context 
4/10 vlan-id 2          120.2.0.241    00:01:02:03:01:02   86400 Wed
Nov  7 22:21:11 2005    Proxy local
4/10 vlan-id 7          120.2.199.114  00:01:02:03:01:07   86400 Wed
Nov  7 22:19:55 2005    Proxy local
4/10 vlan-id 9          120.2.199.121  00:01:02:03:01:09   86400 Wed
Nov  7 22:21:03 2005    Proxy local

The following example shows how to display all the DHCP relay hosts that have duplicate MAC addresses:

[local]Redback#show dhcp relay hosts duplicate-mac
Circuit                     Host        Hardware address    Lease   Ttl    Timestamp

                 Type     Context10/4 vlan-id 2 clips 131135 15.1.1.200  00:aa:aa:aa:00:01   72000  71695  Wed Aug 29 10:13:39    2007    Relay    local
10/4 vlan-id 4 clips 131125 17.1.1.200  00:aa:aa:aa:00:01   72000  71695  Wed Aug 29 10:13:44    2007    Relay    local
10/4 vlan-id 2 clips 131128 15.1.1.100  00:aa:aa:aa:00:02   72000  71695  Wed Aug 29  10:14:29 2007    Relay    local
10/4 vlan-id 4 clips 131116 17.1.1.199  00:aa:aa:aa:00:02   72000  71695  Wed Aug 29  10:14:21 2007    Relay    local
10/4 vlan-id 2 clips 131126 15.1.1.198  00:aa:aa:aa:00:03   72000  71695  Wed Aug 29  10:14:16 2007    Relay    local
10/4 vlan-id 4 clips 131117 17.1.1.196  00:aa:aa:aa:00:03   72000  71695  Wed Aug 29  10:13:45 2007    Relay    local
10/4 vlan-id 2 clips 131127 15.1.1.197  00:aa:aa:aa:00:04   72000  71695  Wed Aug 29  10:14:02 2007    Relay    local

The following example displays information for the DHCP relay host that has the IP address of 200.100.1.3:

[local]Redback>show dhcp relay hosts 200.100.1.3
---------------------------------------------------------------------
Displaying information for host: 200.100.1.3
MAC Address         : 02:dd:00:00:00:26
Circuit             : 12/5 vlan-id 101
Context             : sj8
Circuit Handle      : 12/5:1023:63/1/2/8194
Create time         : Tue Dec  2 14:50:30 2008
Type                : Server
Server              : 200.100.1.1
Lease               : 900            Ttl                 : 892
giaddr              : 0.0.0.0        flags               : 0x411805
helper flags        : 0xa            Standby helper flags: 0x2
Act. File Page #    : 0              Act. File Page Elem : 0
Sby. File Page #    : 1148           Sby. File Page Elem : 0
Agent-Circuit-id    : 0x0a0b0c0d0e
Agent-Remote-id     : defghijklm

1.5   show dhcp relay server

show dhcp relay server [detail]

1.5.1   Purpose

Displays information about the Dynamic Host Configuration Protocol (DHCP) relay server.

1.5.2   Command Mode

all modes

1.5.3   Syntax Description

detail

Optional. Displays more detailed information about the DHCP relay servers.

1.5.4   Default

None

1.5.5   Usage Guidelines

Use the show dhcp relay server command to display information about the DHCP relay server.

Note:  
By default, most show commands (in any mode) display information for the current context only or, depending on the command syntax, for all contexts. If you are an administrator for the local context, you can insert the optional context ctx-name construct, preceding the show command, to view output for the specified context without entering that context. For more information about using the context ctx-name construct, see the context command description.

Note:  
By appending a space followed by the pipe ( | ) character at the end of a show command, you can filter the output using a set of modifier keywords and arguments. For more information, see “Modifying Output of show Commands” in Using the CLI.

1.5.6   Examples

The following example displays DHCP relay server information:

[local]Redback>show dhcp relay server



Server Name/IP Address                MinWait   MaxHops   Group

10.2.1.1                              0         4         default

The following example displays detailed DHCP relay server information:

[local]Redback>show dhcp relay server detail



DHCP Relay server           : 10.2.1.1

Minimum wait                : 0         Maximum hops                : 4

Server Group grid           : 0x1

Server group                : default



Server is available                          : Yes



Route to the server available                : Yes

Source ipaddress for server bound pkts       : 10.2.1.2

Dhcp relay option (82) enabled               : FALSE

Stats-----------------------------------------------------------------

Discover Tx                 : 5367      Request Tx                  : 5063

Release Tx                  : 5000      Decline Tx                  : 0

Offer Rx                    : 5277      Ack Rx                      : 5000

Nack Rx                     : 0         No. of leases               : 5000

1.6   show dhcp relay stats

show dhcp relay stats

1.6.1   Purpose

Displays Dynamic Host Configuration Protocol (DHCP) relay statistics.

1.6.2   Command Mode

all modes

1.6.3   Syntax Description

This command has no keywords or arguments.

1.6.4   Default

None

1.6.5   Usage Guidelines

Use the show dhcp relay stats command to display DHCP relay statistics.

Note:  
By default, most show commands (in any mode) display information for the current context only or, depending on the command syntax, for all contexts. If you are an administrator for the local context, you can insert the optional context ctx-name construct, preceding the show command, to view output for the specified context without entering that context. For more information about using the context ctx-name construct, see the context command description.

Note:  
By appending a space followed by the pipe ( | ) character at the end of a show command, you can filter the output using a set of modifier keywords and arguments. For more information, see “Modifying Output of show Commands” in Using the CLI.

1.6.6   Examples

The following example displays output from the show dhcp relay stats command:

[local]Redback>show dhcp relay stats 



Packets Received    : 96             Packets Relayed     : 86



DHCP Discover       : 20             DHCP Offer          : 20

DHCP Request        : 26             DHCP Decline        : 0

DHCP Ack            : 20             DHCP Nack           : 0

BOOTP Request       : 0              BOOTP Reply         : 0

Bad Length          : 0              Bad Circuit         : 4

Bad Context         : 0              Bad Server IP       : 0

No Server           : 0              No Interface        : 0

Unbound Circuit     : 0              Disabled Interface  : 0

Min Wait Error      : 0              Max Hops Error      : 0

Bad IP              : 0              Unknown Packet Type : 0

TX Error            : 0              Unmatched MAC       : 0

Send Client Error   : 0              Send Client Retries : 0

Offer pkt: count    : 40             Offer pkt: refresh  : 0

ARP Table Error     : 0



Input pack Q full (packet drops):: 0

Input pack Q mem error:: 0

Input pack Q (enqueued) count:: 92

Input pack Q (dequeued) count:: 92

1.7   show dhcp relay summary

show dhcp relay summary

1.7.1   Purpose

Displays a summary of Dynamic Configuration Host Protocol (DHCP) relay host information.

1.7.2   Command Mode

1.7.3   Syntax Description

This command has no keywords or arguments.

1.7.4   Default

None

1.7.5   Usage Guidelines

Use the show dhcp relay summary command to display a summary of DHCP relay host information.

Note:  
By default, most show commands (in any mode) display information for the current context only or, depending on the command syntax, for all contexts. If you are an administrator for the local context, you can insert the optional context ctx-name construct, preceding the show command, to view output for the specified context without entering that context. For more information about using the context ctx-name construct, see the context command description.

Note:  
By appending a space followed by the pipe ( | ) character at the end of a show command, you can filter the output using a set of modifier keywords and arguments. For more information, see “Modifying Output of show Commands” in Using the CLI.

1.7.6   Examples

The following example displays a summary of DHCP relay host information. The Host count column lists the number of hosts in the current context, while the Total Host count column lists the number of hosts in the system:

[local]Redback>show dhcp relay summary



Host count          :   26

Total Host count    : 2626

1.8   show dhcp server

show dhcp server {leases | hosts} [{count | duplicate-mac | ip-address ip-addr | mac-address mac-addr | {subnet subnet-ip-addr/prefix-length | netmask} [count] | time-remaining {at-least | at-most} time-remaining [count]}]

1.8.1   Purpose

Displays information about the hosts or leases for the internal Dynamic Host Configuration Protocol (DHCP) server.

1.8.2   Command Mode

1.8.3   Syntax Description

leases

Displays all information about one or more DHCP leases.

hosts

Displays all information about one or more DHCP hosts.

count

Optional. Displays the number of leases or hosts, the number of subnets, or the number of leases or hosts for the time remaining.

duplicate-mac

Optional. Displays leases or hosts with duplicate medium access control (MAC) addresses in the current context.

ip-address ip-addr

Optional. IP address for a DHCP host or lease.

mac-address mac-addr

Optional. MAC address for the DHCP host or lease.

subnet subnet-ip-addr

Optional. IP address for the subnet for a DHCP lease or host.

prefix-length

Prefix length for the associated subnet; the range of values is 0 to 32.

netmask

Network mask for the associated subnet; the range of values is 255.255.0.0 to 255.255.255.255.

time-remaining

Optional. Displays the time remaining for one or more DHCP leases or hosts.

at-least

Displays DHCP leases or hosts with a time remaining equal to or greater than the value of the time-remaining argument.

at-most

Displays DHCP leases or hosts with a time remaining equal to or less than the value of the time-remaining argument.

time-remaining

Number of seconds remaining for a DHCP lease or host; the range of values is 0 to 4,294,967,295.

1.8.4   Default

When entered without any optional syntax, the show dhcp server command displays all information about all hosts or leases for the internal DHCP server.

1.8.5   Usage Guidelines

Use the show dhcp server command to display information about the hosts or leases for the internal DHCP server.

Note:  
By default, most show commands (in any mode) display information for the current context only or, depending on the command syntax, for all contexts. If you are an administrator for the local context, you can insert the optional context ctx-name construct, preceding the show command, to view output for the specified context without entering that context. For more information about using the context ctx-name construct, see the context command description.

Note:  
By appending a space followed by the pipe ( | ) character at the end of a show command, you can filter the output using a set of modifier keywords and arguments. For more information, see “Modifying Output of show Commands” in Using the CLI.

1.8.6   Examples

The following example displays the DHCP lease information:

[local]Redback>show dhcp server leases



Circuit  Host               Hardware address     Lease       Ttl         Timestamp                 Type        Context

2/1      100.100.10.202     00:dd:00:00:00:01    1600        1491

Fri Feb  3 22:09:48 2006  Server      dhcpserver

2/1      100.100.10.205     00:dd:00:00:00:04    1600        1492        Fri Feb  3 22:09:49 2006  Server      dhcpserver

2/1      100.100.10.204     00:dd:00:00:00:03    1600        1492

Fri Feb  3 22:09:49 2006  Server      dhcpserver

The following example displays the number of DHCP hosts:

[local]Redback>show dhcp server hosts count



Number of leases is 100

The following example displays the number of hosts with at least 360 seconds remaining on their leases:

[local]Redback>show dhcp server hosts time-remaining at-least 360 count



Number of leases is 100

1.9   show dhcp server file

show dhcp server file {context [{name ctx-name | start name ctx-name}] | header | session [{mac-addr | start mac-addr}]}

1.9.1   Purpose

Displays file information for a Dynamic Host Configuration Protocol (DHCP) server.

1.9.2   Command Mode

1.9.3   Syntax Description

context

Display context information.

name ctx-name

Name of a context that is configured for a DHCP server.

start

Display context or session information starting with the specified context or medium access control (MAC) address.

header

Display header information.

mac-addr

MAC address for which session information is to be displayed.

session

Display session information.

1.9.4   Default

None

1.9.5   Usage Guidelines

Use the show dhcp server file command to display file information for a DHCP server.

Note:  
By default, most show commands (in any mode) display information for the current context only or, depending on the command syntax, for all contexts. If you are an administrator for the local context, you can insert the optional context ctx-name construct, preceding the show command, to view output for the specified context without entering that context. For more information about using the context ctx-name construct, see the context command description.

Note:  
By appending a space followed by the pipe ( | ) character at the end of a show command, you can filter the output using a set of modifier keywords and arguments. For more information, see “Modifying Output of show Commands” in Using the CLI.

1.9.6   Examples

The following example displays DHCP file header information:

[local]Redback>show dhcp server file header



Magic:   SaVe

Version: 10

Type:    1

Valid:   Yes

1.10   show dhcp server option-82

show dhcp server option-82 circuit-id [string]

1.10.1   Purpose

Displays the maximum number of IP addresses allowed and the number of IP addresses currently assigned to one or more agent circuit IDs.

1.10.2   Command Mode

1.10.3   Syntax Description

circuit-id

Displays agent circuit ID information.

string

Optional. Agent circuit ID for which IP address information is to be displayed.

1.10.4   Default

None

1.10.5   Usage Guidelines

Use the show dhcp server option-82 command to display the maximum number of IP addresses allowed and the number of IP addresses currently assigned to one or more agent circuit IDs.

Note:  
By default, most show commands (in any mode) display information for the current context only or, depending on the command syntax, for all contexts. If you are an administrator for the local context, you can insert the optional context ctx-name construct, preceding the show command, to view output for the specified context without entering that context. For more information about using the context ctx-name construct, see the context command description.

Note:  
By appending a space followed by the pipe ( | ) character at the end of a show command, you can filter the output using a set of modifier keywords and arguments. For more information, see Modifying Output of show Commands in Using the CLI.

1.10.6   Examples

The following example displays all agent circuit IDs:

[local]Redback>show dhcp server option-82 circuit-id



Agent-circuit-id         Max IP          IP assigned

----------------------------------------------------

slot8-port0-channel0     10              5

1.11   show dhcp server range

show dhcp server range [if-name]

1.11.1   Purpose

Displays range usage information for one or more interfaces configured for a Dynamic Host Configuration Protocol (DHCP) server.

1.11.2   Command Mode

1.11.3   Syntax Description

if-name

Optional. Name of an interface that is configured for a DHCP server.

1.11.4   Default

When entered without any optional syntax, the show dhcp server range command displays range usage information for all interfaces configured for a DHCP server.

1.11.5   Usage Guidelines

Use the show dhcp server range command to display range usage information for one or more interfaces configured for a DHCP server.

Note:  
By default, most show commands (in any mode) display information for the current context only or, depending on the command syntax, for all contexts. If you are an administrator for the local context, you can insert the optional context ctx-name construct, preceding the show command, to view output for the specified context without entering that context. For more information about using the context ctx-name construct, see the context command description.

Note:  
By appending a space followed by the pipe ( | ) character at the end of a show command, you can filter the output using a set of modifier keywords and arguments. For more information, see “Modifying Output of show Commands” in Using the CLI.

1.11.6   Examples

The following example displays range information for the to-client interface:

[local]Redback>show dhcp server range to-client



Interface "to-client":

  10.1.0.1        10.1.255.254                  0 in use, 65533 free,1 reserved

1.12   show dhcp server stats

show dhcp server stats [{circuit slot/port circuit-id [pending mac-addr] | context ctx-name interface if-name [pending mac-addr]}]

1.12.1   Purpose

Displays Dynamic Host Configuration Protocol (DHCP) process statistics.

1.12.2   Command Mode

1.12.3   Syntax Description

circuit slot/port

Slot and port numbers for the traffic card that holds the circuit to be displayed.

circuit-id

Circuit identifier, according to one of the constructs listed in Table 1.

pending mac-addr

Optional. DHCP host entry for the specified medium access control (MAC) address.

context ctx-name

Context for which DHCP statistics are displayed.

interface if-name

Interface in the specified context for which DHCP statistics are displayed.

1.12.4   Default

When entered without any optional syntax, the show dhcp server stats command displays DHCP process statistics.

1.12.5   Usage Guidelines

Use the show dhcp server stats command to display DHCP process statistics. Table 1 lists the values for the circuit-id argument.

Table 1    Values for the circuit-id Argument

Construct

Description

clips

Clientless IP service selection (CLIPS) circuit.

dlci dlci

Data-link connection identifier (DLCI) for a Frame Relay permanent virtual circuit (PVC). The range of values is 16 to 991.

vlan-id vlan-id

Virtual LAN (VLAN) tag value for an 802.1Q tunnel or PVC. The vlan-id argument is one of the following constructs:

  • pvc-vlan-id—VLAN tag value of a PVC that is not within an 802.1Q tunnel.

  • tunl-vlan-id—VLAN tag value of a tunnel.

  • tunl-vlan-id:pvc-vlan-id—VLAN tag value for the tunnel followed by the VLAN tag value for the PVC within the tunnel.

The range of values for either VLAN tag value is 1 to 4,095.

vpi-vci vpi vci

Virtual path identifier (VPI) and virtual circuit identifier (VCI) for an Asynchronous Transfer Mode (ATM) PVC. The range of values is 0 to 255 and 1 to 65,535, respectively.

Note:  
By default, most show commands (in any mode) display information for the current context only or, depending on the command syntax, for all contexts. If you are an administrator for the local context, you can insert the optional context ctx-name construct, preceding the show command, to view output for the specified context without entering that context. For more information about using the context ctx-name construct, see the context command description.

Note:  
By appending a space followed by the pipe ( | ) character at the end of a show command, you can filter the output using a set of modifier keywords and arguments. For more information, see “Modifying Output of show Commands” in Using the CLI.

1.12.6   Examples

The following example displays DHCP statistics for the specified circuit:

[local]Redback>show dhcp server stats circuit 11/4 vlan-id 10



Current time: Fri Aug  4 17:49:44 2006

Last cleared: Never

Internal Circuit Handle: 11/5:1023:63/1/2/10





Discovers Received    : 0                 Requests Received     : 0

Releases Received     : 0                 Declines Received     : 0

Renewal REQs Received : 0

Offers Sent           : 0                 ACKs Sent             : 0

Renewal ACKs Sent     : 0

The following example displays DHCP statistics for the specified interface:

[local]Redback#show dhcp server stats context c1 interface i1



Current time: Fri Aug  4 17:49:46 2006

Last cleared: Never



Discovers Received    : 0                 Requests Received     : 0

Release Received      : 0                 Decline Received      : 0

Renewal REQs Received : 0

Offers Sent           : 0                 ACKs Sent             : 0

Renewal ACKs Sent     : 0

1.13   show dhcp server threshold

show dhcp server threshold {context | range}

1.13.1   Purpose

Displays Dynamic Host Configuration Protocol (DHCP) threshold configuration and status information.

1.13.2   Command Mode

1.13.3   Syntax Description

context

Displays threshold configuration and status for the current context at the context level.

range

Displays threshold configuration for all ranges in the current context.

1.13.4   Default

None

1.13.5   Usage Guidelines

Use the show dhcp server threshold command to display DHCP threshold configuration and status information.

Note:  
By default, most show commands (in any mode) display information for the current context only or, depending on the command syntax, for all contexts. If you are an administrator for the local context, you can insert the optional context ctx-name construct, preceding the show command, to view output for the specified context without entering that context. For more information about using the context ctx-name construct, see the context command description.

Note:  
By appending a space followed by the pipe ( | ) character at the end of a show command, you can filter the output using a set of modifier keywords and arguments. For more information, see “Modifying Output of show Commands” in Using the CLI.

1.13.6   Examples

The following example displays the threshold configuration for all ranges in the current context:

[local]Redback>show dhcp server threshold range



Interface "subs":

100.100.10.2    100.100.10.254   threshold falling 10 log

1.14   show diag

For any SmartEdge chassis except the SmartEdge 100 chassis, to display the results of the power-on diagnostic (POD) tests:

show diag pod [backplane [detail] | card slot [detail] | fantray [detail] | detail]

For a SmartEdge 100 chassis, to display the results of the POD tests:

show diag pod [card [detail] | detail]

For any SmartEdge chassis except the SmartEdge 100 chassis, to display the results of the on-demand diagnostic (ODD) tests:

show diag on-demand [card slot [disk disk_num] [detail] | mesh [detail] | standby [detail] | history num-ses [detail] | detail]

For a SmartEdge 100 chassis, to display the results of the ODD tests:

show diag on-demand [card [detail] | history num-ses [detail] | detail]

1.14.1   Purpose

Displays the results of POD or ODD tests for one or more units.

1.14.2   Command Mode

all modes

1.14.3   Syntax Description

pod

Displays results from the POD tests.

on-demand

Displays results from the ODD tests.

backplane

Optional. Displays POD results for the backplane in any chassis.

card slot

Optional. Latest results for the card specified by the slot argument.

The range of values for slot is:

  • 1 to 2 for a SmartEdge 100 chassis, where the controller card is installed in slot 1 and the carrier card is installed in slot 2.

  • 1 to 6 for a SmartEdge 400 chassis, where traffic cards are installed in slots 1 through 4 and controller cards are installed slots 5 and 6.

  • 1 to 14 for a SmartEdge 800 or SmartEdge 1200 chassis, where traffic cards are installed in slots 1 through 6 and 9 through 14 and controller cards are installed in slots 7 and 8.

disk disk_num

Optional. Disk number on the SSE card. Values: 1 or 2.

standby

Optional. Displays the latest results for the standby controller card.

fantray

Optional. Displays POD results for the fan tray or the fan and alarm unit in the SmartEdge 800 chassis.

mesh

Optional. Displays results for packet mesh tests.

detail

Optional. Displays detailed results.

history num-ses

Optional. Previous results from the history file for the number of ODD sessions specified by the num-ses argument. The first set of results is for the last initiated session. The range of values is 1 to 100.

pod

Displays results from the POD tests.

on-demand

Displays results from the ODD tests.

backplane

Optional. Displays POD results for the backplane in any chassis.

card slot

Optional. Latest results for the card specified by the slot argument.

The range of values for slot is:

  • 1 to 2 for a SmartEdge 100 chassis, where the controller card is installed in slot 1 and the carrier card is installed in slot 2.

  • 1 to 6 for a SmartEdge 400 chassis, where traffic cards are installed in slots 1 through 4 and controller cards are installed slots 5 and 6.

  • 1 to 14 for a SmartEdge 800 or SmartEdge 1200 chassis, where traffic cards are installed in slots 1 through 6 and 9 through 14 and controller cards are installed in slots 7 and 8.

standby

Optional. Displays the latest results for the standby controller card.

fantray

Optional. Displays POD results for the fan tray or the fan and alarm unit in the SmartEdge 800 chassis.

mesh

Optional. Displays results for packet mesh tests.

detail

Optional. Displays detailed results.

history num-ses

Optional. Previous results from the history file for the number of ODD sessions specified by the num-ses argument. The first set of results is for the last initiated session. The range of values is 1 to 100.

1.14.4   Default

For POD, displays a summary of the results for all units. For ODD, displays summary results for all cards from the last initiated session.

1.14.5   Usage Guidelines

Use the show diag command to display the results of the POD or ODD tests for one or more units.

Results for POD are updated whenever a card is installed in the chassis of a running system, or the system is reloaded using the reload command (in exec mode). Only the latest results are displayed.

The latest results for POD are stored in a log with a buffer for each card. The system also stores the log and maintains a history file on the compact-flash card for low-level software to store results for up to 100 sessions.

For POD, use the detail keyword to determine which tests the unit has failed.

No POD results are reported for unprovisioned cards. You must first provision a card before POD results for it can be reported.

For ODD, use the detail keyword to display all data in the summary, and, for each test that failed, the details about the test failure. This keyword can be combined with any other keyword or argument; if it is the only keyword specified, it displays detailed results from the last session.

For the SmartEdge 100 chassis, use the history keyword to display results of previous ODD sessions; for any other SmartEdge chassis, use the history num-ses construct. The first set of results is for the last initiated session.

For the SmartEdge 100 chassis, use the card keyword to display the log for the carrier card; for any other SmartEdge chassis, use the card slot construct to display the log for any traffic card.

Table 2 lists the possible summary results for an ODD session.

Table 2    Status Descriptions for ODD Sessions

Session Status

Description

Aborted

Session was terminated by the user.

Incomplete

At least one of the requested tests could not be run.

In-Progress

Session is currently in progress.

n Failures

Number of test failures that occurred during the session.

Passed

All tests passed.

Table 3 lists the descriptions for the test status that can be displayed.

Table 3    Descriptions for Test Status

Test Status

Description

Aborted

Test was started but was terminated before it could be completed.

Failed

Test ran and failed.

Not Run

Initial state, test not yet run.

Passed

Test ran successfully.

Running

Test is currently in progress.

Skipped

Test could not be run; for example, part revision is earlier than the required minimum version or no file found.

In general, if a unit fails to pass a test, you should replace it or make arrangements for its replacement. Contact your local technical support representative for more information about the results of a failed test. For troubleshooting information on uncorrected file system error recovery on an SSE card, see SSE Configuration and Operation.

Note:  
In the case of a mesh test failure, the test results can mean that one of the cards has failed, one of the slots has failed, or that the mesh itself has failed. Use the detail keyword with the show diag command to display the results of the mesh test; depending on the results, you can run the mesh test several times with different slot combinations. Mesh test results are cumulative to allow you to view the results of all slot combinations as an aid in determining the failure condition before notifying your local technical support representative or the support organization.

Note:  
If the version of the Sys FPGA on a traffic card is not 0x7 or later, the voltage check, temperature check, and bus tests cannot be run; they are skipped, and the session status is reported as “Incomplete”. To resolve the problem, enter the show hardware command with the card and detail keywords (in any mode) to display the FPGA version in the SysFpga field. To upgrade this FPGA to the latest version, contact your local technical representative or the support organization.

Note:  
By default, most show commands (in any mode) display information for the current context only or, depending on the command syntax, for all contexts. If you are an administrator for the local context, you can insert the optional context ctx-name construct, preceding the show command, to view output for the specified context without entering that context. For more information about using the context ctx-name construct, see the context command description.

Note:  
By appending a space followed by the pipe ( | ) character at the end of a show command, you can filter the output using a set of modifier keywords and arguments. For more information, see “Modifying Output of show Commands” in Using the CLI.

1.14.6   Examples

Example 1

The following command line is used to show the summary results of the POD tests:

[local]Redback#show diag pod

Example 2

The following command line is used to show the detailed results of the POD tests for the card in slot 2:

[local]Redback#show diag pod card 2 detail

Example 3

The following command line is used to show the detailed of the POD results for the card in slot 7:

[local]Redback#show diag pod card 7 detail

Example 4

The following example displays the summary results for the ODD level 2 test on the traffic card in slot 2:

[local]Redback#show diag on-demand card 2

Example 5

The following example shows the detailed results of the mesh ODD test of a SmartEdge 400 chassis. “P” indicates a passed condition, “F” indicates a failed condition, and “-” indicates not applicable. The system keeps track of mesh test failures from previous mesh test runs and displays summary results for all traffic card slots. The diag on-demand mesh reset command clears this summary information (resets the values to -):

[local]Redback#show diag on-demand mesh detail

Slot Number             : 1
Card Type               : oc3-8-port
Detected Card Type      : oc3-8-port
Serial Number           : 8J0O8070200146
Detected Serial Number  : 8J0O8070200146
Test Summary            : 1 Failure detected
Slot Number             : 2
Card Type               : ether-12-port
Detected Card Type      : ether-12-port
Serial Number           : 7U123456789012
Detected Serial Number  : 7U123456789012
Test Summary            : 1 Failure detected
Slot Number             : 3
Card Type               : oc48-1-port
Detected Card Type      : oc48-1-port
Serial Number           : 8L0E6090100666
Detected Serial Number  : 8L0E6090100666
Test Summary            : Incomplete - 3 tests skipped
Controller Serial Number: 6Y038050200239
Test Level              : Mesh
Loop Count              : 1
Start Time              : 23:25:23  11/09/2002
Completion Time         : 23:27:58  11/09/2002
Mesh Test Summary       : Passed

Test Results Loop 1:
    Tx    Pkts     Rx    Pkts
  Slot    Sent   Slot    Recv  Status
  -----------------------------------
     1   37500      2   36498  Failed

Summary Results of Mesh Bus Testing
  Tx/Rx    1    2    3    4   XC   XC 
  -----------------------------------
      1    -   *F*   P    -    -    - 
      2    P    -    P    -    -    - 
      3    P    P    -    -    -    - 
      4    -    -    -    -    -    - 
     XC    -    -    -    -    -    - 
     XC    -    -    -    -    -    - 

Example 6

The following example displays the controller card and carrier card results of the on-demand testing of a SmartEdge 100 chassis:

[local]Redback#show diag on-demand

Slot Number             : 1
Card Type               : XCRP
Detected Card Type      : none
Serial Number           : A90J5080500069
Detected Serial Number  : 
Controller Serial Number: 8N026090100864
Test Level              : 3
Loop Count              : 1
Start Time              : 21:53:50  05/9/2006
Completion Time         : 21:54:37  05/9/2006
Test Summary            : Passed
Slot Number             : 2
Card Type               : carrier
Detected Card Type      : none
Serial Number           : A80C5040500029
Detected Serial Number  : 
Controller Serial Number: 8N026090100864
Test Level              : 3
Loop Count              : 1
Start Time              : 21:55:31  05/09/2006
Completion Time         : 21:57:11  05/09/2006
Test Summary            : 1 Failure

MIC 1
MIC Type                : ge-2-port
Detected MIC Type       : none
Serial Number           : A80C5040500029
Detected Serial Number  : 
Controller Serial Number: 8N026090100864
Test Level              : 3
Loop Count              : 1
Start Time              : 21:55:31  05/09/2006
Completion Time         : 21:57:11  05/09/2006
Test Summary            : 1 Failure

MIC 2
MIC Type                : ge-2-port
Detected MIC Type       : none
Serial Number           : A80C5040500029
Detected Serial Number  : 
Controller Serial Number: 8N026090100864
Test Level              : 3
Loop Count              : 1
Start Time              : 21:55:31  05/09/2006
Completion Time         : 21:57:11  05/09/2006
Test Summary            : Passed.

1.15   show disk

show disk [internal | external] [detail]

1.15.1   Purpose

Displays status for the internal (NetBSD compact-flash card) card, and the external (mass-storage device) card, if installed, and the soft and hard error count, in the external slot of the controller card to which you are connected.

1.15.2   Command Mode

1.15.3   Syntax Description

internal

Optional. Displays status for the root file system on the NetBSD compact-flash card.

external

Optional. Displays status for the /md file system on the mass-storage device.

detail

Optional. Displays detailed results.

1.15.4   Default

Displays status for both the root and /md file systems.

1.15.5   Usage Guidelines

Use the show disk command to display status for the internal (NetBSD compact-flash card) card, and the external (mass-storage device) card, if installed, and the soft and hard error count, in the external slot of the controller card to which you are connected.

Table 4 lists the fields displayed by this command.

Table 4    Field Descriptions for the show disk Command

Field

Description

Location

Location of the storage device:

  • internal—Internal-storage device (compact-flash card) typically installed in a slot

  • external—External-storage device installed in an external slot

512-blocks

Size of the file system in 512-byte blocks:

  • 362,526—192-MB internal compact-flash card, root file system

  • 484,079—256-MB internal compact-flash card, root file system

  • 968,158—512-MB internal compact-flash card, root file system

  • 1,021,244—1-GB mass-storage device, /md file system

Used

Number of blocks in use

Avail

Number of blocks available

Capacity

Percent of blocks used in the file system, calculated using the number of usable blocks (Used + Avail)

Mounted on

Device on which the file system is mounted:

  • /—Internal compact-flash card

  • /md—Mass-storage device in the external slot

Note:  

The following notes apply to the data in Table 4:


Table 5 lists the additional fields that are displayed by the show disk command when you include the detail keyword.

Table 5    Field Descriptions for the show disk Command with the detail Keyword

Field

Description

Controller Status

Controller status flags:

  • I—Failed to clear an interruption

  • N—New event not yet processed

  • P—Device present

Num attach/detach

Number of times an external device was inserted or removed

Disk Status

A—Attached

C—Changing the current directory failed (cd command failure)

D—Change to file permissions failed

E—Installed in external slot

F—File system check failed

I—Installed in internal slot

M—Mounted

N—Creation of a new file system failed

O—Automatic mount failed

R—Reformatting disk

S—Failed to attach an external disk as a core dump device

T—Unmount command failed

U—Automatically mounted

Disk # of event

Number of times the operating system notified applications that the external device was inserted

Note:  

A soft error is any error that is abnormal but recoverable on the system, during the drive or compact-flash operation. The soft error counter is incremented when one of the following conditions occurs:

A hard error occurs when the system cannot read the drive information or when an error is not recoverable. Typically, if a hard error occurs, the drive needs to be replaced.

The hard error counter is incremented when one of the following conditions occurs:


Note:  
By default, most show commands (in any mode) display information for the current context only or, depending on the command syntax, for all contexts. If you are an administrator for the local context, you can insert the optional context ctx-name construct, preceding the show command, to view output for the specified context without entering that context. For more information about using the context ctx-name construct, see the context command description.

Note:  
By appending a space followed by the pipe ( | ) character at the end of a show command, you can filter the output using a set of modifier keywords and arguments. For more information, see “Modifying Output of show Commands” in Using the CLI.

1.15.6   Examples

The following example displays detailed status for the mass-storage device in the external slot of the active controller card:

[local]Redback>show disk external
Controller Status Flags                                       

Flags: P - device presenct, I - Failed to clear an interrupt,

       N - New event not processed                            

--------------------------------------------------------------

Controller status: P

Num attach/detach: 1/1

Card Status Flags                                             

Flags: A - Attached, M - Mounted        

       U - Automatically mounted, F - Filesystem check failed  

       N - Creation of new filesystem failed,        O - automatic mount failed,          

       C - changing the current directory failed,        S - Swap failed, T - unmount failed  

       D - change to file permissions failed

--------------------------------------------------------------

Disk status: AMU

Disk # evnt: 3





Mount Time : Mon Apr 18 10:56:15 2005 PST

Mounted in slot: 6 Status : Operational

Soft Errors : 0 Hard Errors: 0

Location  512-blocks     Used    Avail    Capacity  Mounted on

External  1021244        54118   916062   5%        /md

The following example displays status for the NetBSD compact-flash card and the mass-storage device on the active controller card:

[local]Redback>show disk 
Location  512-blocks     Used    Avail    Capacity  Mounted on

Internal  985262         309074  626924   33%       /

External  1021244        45146   925034    4%       /md

The following example displays status for the NetBSD compact-flash card and the mass-storage device on the standby controller card:

[local]standby#show disk
Location      512-blocks     Used     Avail    Capacity  Mounted on

Internal      362526         254592   89806    73%        /

External      1021244        59426    910754    6%       /md

1.16   show disk sse

show disk sse slot [disk_num]

1.16.1   Command Mode

all modes

1.16.2   Syntax Description

slot

Chassis slot number of the SSE card.

disk_num

Disk number on the SSE card. Values: 1 or 2.

1.16.3   Usage Guidelines

Displays SSE disk information for the SSE card.

1.16.4   Examples

[local]Redback#show disk sse 2
Slot                : 2
State               : Up
FS Group Name       : grp1
Active Alarms       : NONE

Disk Info           :
-------------------------------------------------
Disk                : 1            State               : Up
Total Size (GB)     : 134.12       Available (GB)      : 130.11
Active Alarms       : NONE

Disk                : 2            State               : Up
Total Size (GB)     : 134.00       Available (GB)      : 134.00
Active Alarms       : NONE

# of Partitions     : 2
-------------------------------------------------
Name                : ptn1
In FS Group         : Yes
Disk Allocated      : 1
Size (GB)           : 2.00

Name                : ptn2
In FS Group         : Yes
Disk Allocated      : 1
Size (GB)           : 2.00
[local]Redback#show disk sse 5
Slot                : 5
State               : Up
FS Group Name       : grp1
Active Alarms       : NONE

Disk Info           :
-------------------------------------------------
Disk                : 1            State               : Up
Total Size (GB)     : 134.12       Available (GB)      : 130.11
Active Alarms       : NONE


# of Partitions     : 0
-------------------------------------------------

1.17   show disk sse counters

show disk sse counters slot [disk_num]

1.17.1   Command Mode

all modes

1.17.2   Syntax Description

slot

Chassis slot number of the SSE card.

disk_num

Disk number on the SSE card. Values: 1 or 2.

1.17.3   Usage Guidelines

Displays SSE disk counters for the SSE card.

1.17.4   Examples

[local]Redback#show disk sse counters 2
timestamp: 11465058820
timestamp secs: 11465  timestamp usecs: 58820

Disk Counters       :
-------------------------------------------------
Disk                : 1
Transfers (ps)      : 93.08
Writes (kbps)       : 15.45        Reads (kbps)        : 6981.33
Total Write (kb)    : 4659
Total Read (kb)     : 2105917
Write Reqs (ps)     : 0.22         Read Reqs (ps)      : 142.36
Sector Writes (ps)  : 15.45        Sector Reads (ps)   : 6981.09
Avg Req Sz (sectors): 150.34
Avg Wait (ms)       : 11.54        Avg Servicing (ms)  : 0.93

Disk                : 2
Transfers (ps)      : 1.02
Writes (kbps)       : 0.11         Reads (kbps)        : 7.36
Total Write (kb)    : 32
Total Read (kb)     : 2220
Write Reqs (ps)     : 0.03         Read Reqs (ps)      : 10.66
Sector Writes (ps)  : 0.11         Sector Reads (ps)   : 7.36
Avg Req Sz (sectors): 14.67
Avg Wait (ms)       : 0.95         Avg Servicing (ms)  : 0.85

1.18   show dot1q counters

show dot1q counters [persistent] [slot/port [vlan-id vlan-id]] [detail]

1.18.1   Purpose

Displays counter information for 802.1Q permanent virtual circuits (PVCs).

1.18.2   Command Mode

all modes

1.18.3   Syntax Description

persistent

Optional. If omitted, displays values since the counters were last cleared or the card was last reloaded. If specified, displays values since the system was last reloaded.

slot

Optional. Chassis slot number of the traffic card for which counters are displayed.

port

Required if you enter the slot argument. Port number of the port for which counters are displayed.

vlan-id vlan-id

Virtual LAN (VLAN) tag value for an 802.1Q tunnel or PVC. The vlan-id argument is one of the following constructs:

  • pvc-vlan-id—VLAN tag value of a PVC that is not within an 802.1Q tunnel.

  • tunl-vlan-id—VLAN tag value of a tunnel.

  • tunl-vlan-id:pvc-vlan-id—VLAN tag value for the tunnel followed by the VLAN tag value for the PVC within the tunnel.

The range of values for any VLAN tag value is 1 to 4095.

detail

Optional. Specifies that more details are displayed for each 802.1Q PVC.

1.18.4   Default

Displays counter information on all 802.1Q tunnels and PVCs on the system.

1.18.5   Usage Guidelines

Use the show dot1q counters command to display counter information for 802.1Q PVCs.

Note:  
This command is an alias for the show circuit counters dot1q command in exec mode.

If you enter the optional slot and port arguments, the output displays circuit counters for the specified card or port; otherwise, the output displays only summary counter information for all 802.1Q PVCs.

Note:  
The SmartEdge 100 router limits the value of the slot argument to 2.

Note:  

The value for the port argument on the SmartEdge 100 router is either of the following:


If you enter the optional vlan-id vlan-id construct, the output displays counters for the specified 802.1Q PVC.

If you specify the VLAN tag value for an 802.1Q tunnel, the output includes circuit counters for all the PVCs within the tunnel.

Note:  
By default, most show commands (in any mode) display information for the current context only or, depending on the command syntax, for all contexts. If you are an administrator for the local context, you can insert the optional context ctx-name construct, preceding the show command, to view output for the specified context without entering that context. For more information about using the context ctx-name construct, see the context command description.

Note:  
By appending a space followed by the pipe ( | ) character at the end of a show command, you can filter the output using a set of modifier keywords and arguments. For more information, see “Modifying Output of show Commands” in Using the CLI.

1.18.6   Examples

The following example shows how to display counters for all 802.1Q PVCs on port 4/1:

[local]Redback>show dot1q counters 4/1
Circuit                         Packets/Bytes Sent  Packets/Bytes Received

4/1  vlan-id 2                  0                   0

4/1  vlan-id 3                  0                   0

4/1  vlan-id 4                  0                   0

4/1  vlan-id 5                  0                   0

4/1  vlan-id 6                  0                   0

4/1  vlan-id 7                  0                   0

4/1  vlan-id 8                  0                   0

1.19   show dot1q profile

show dot1q profile [prof-name | detail]

1.19.1   Purpose

Displays information for one or more 802.1Q permanent virtual circuit (PVC) profiles.

1.19.2   Command Mode

all modes

1.19.3   Syntax Description

prof-name

Optional. Name of the profile to be displayed.

detail

Optional. Displays detailed information for all profiles.

1.19.4   Default

Displays information for all 802.1Q PVC profiles.

1.19.5   Usage Guidelines

Use the show dot1q profile command to display information for one or more 802.1Q PVC profiles.

If you do not specify the prof-name argument or detail keyword, this command displays a list of all 802.1Q profiles with their descriptions and PVC counts.

Use the prof-name argument to display the same detailed information is displayed with the detail keyword; use the detail keyword to display the information for all 802.1Q profiles. Table 6 lists the fields displayed with the detail keyword.

Table 6    Field Descriptions for the show dot1q profile Command

Field

Description

Profile Name

Name specified with the dot1q profile command in global configuration mode.

Description

Text string specified with the description command in dot1q profile configuration mode.

PVC Count

Number of 802.1Q PVCs that reference this profile.

Nas-port-type

  • port-type—Value specified with the radius attribute nas-port-type command in dot1q profile configuration mode.

  • Not set—No value specified.

Propagate Qos from ether

State of QoS propagation as specified by the propagate qos from ethernet command in dot1q profile configuration mode:

  • Disabled

  • Enabled

Propagate Qos to ether

State of QoS propagation as specified by the propagate qos to ethernet command in dot1q profile configuration mode:

  • Disabled

  • Enabled

Note:  
By default, most show commands (in any mode) display information for the current context only or, depending on the command syntax, for all contexts. If you are an administrator for the local context, you can insert the optional context ctx-name construct, preceding the show command, to view output for the specified context without entering that context. For more information about using the context ctx-name construct, see the context command description.

Note:  
By appending a space followed by the pipe ( | ) character at the end of a show command, you can filter the output using a set of modifier keywords and arguments. For more information, see “Modifying Output of show Commands” in Using the CLI.

1.19.6   Examples

The following example shows how to display profile information for the profile dot:

[local]Redback>show dot1q profile dot



Profile Name               : dot

Description                : 

PVC Count                  : 0

Nas-port-type              : 253

Propagate Qos from ether   : Disabled

Propagate Qos to ether     : Enabled

1.20   show dot1q pvc

show dot1q pvc [link-group-filter] [on-demand-filter | general-filter] [detail]

1.20.1   Purpose

Displays information about 802.1Q permanent virtual circuit (PVCs).

1.20.2   Command Mode

all modes

1.20.3   Syntax Description

link-group-filter

link-group lg-name

Optional. A filter that causes the command to display information only for PVCs in the link group specified by lg-name argument.

on-demand-filter

on-demand [[range] slot/port:ch:sub [vlan-id vlan-id]] [up | down] [all]]

Optional. A filter that causes the command to display information only for on-demand PVCs.

general-filter

[summary] [up | down] [all]

Optional. A general filter that causes the command to display summary information, information only for active or inactive PVCs, or PVCs in all contexts.

range

Optional. The range keyword provides a summary description of all on-demand PVCs in the range specified by slot/port:ch:sub and optionally by vlan-id vlan-id. The up, down, and all keywords do not apply if the range keyword is used.

slot/port:ch:sub

Optional. Chassis slot and port numbers of the traffic card for which 802.1Q PVCs are displayed. For channelized media, the channel number (ch) and subchannel number (sub) can also be specified.

vlan-id vlan-id

Optional. Virtual LAN (VLAN) tag value for an 802.1Q tunnel or PVC. The vlan-id argument is one of the following constructs:

  • pvc-vlan-id—VLAN tag value of a PVC that is not within an 802.1Q tunnel.

  • tunl-vlan-id—VLAN tag value of a tunnel.

  • tunl-vlan-id:pvc-vlan-id—VLAN tag value for the tunnel followed by the VLAN tag value for the PVC within the tunnel.

The range of values for any VLAN tag value is 1 to 4095.

up

Optional. Provides information for the specified active 802.1Q PVCs.

down

Optional. Provides information for the specified inactive 802.1Q PVCs.

summary

Optional. Provides summary information.

all

Optional. Provides information for 802.1Q PVCs in all contexts.

detail

Optional. Provides detailed information.

1.20.4   Default

None

1.20.5   Usage Guidelines

Use the show dot1q pvc command to display information about 802.1Q PVCs.

Note:  
The SmartEdge 100 router limits the value of the slot argument to 2.

Note:  

The value for the port argument on the SmartEdge 100 router is one of the following:


If you specify the VLAN tag value for an 802.1Q tunnel, the output includes PVC information for all the PVCs within the tunnel.

Note:  
By default, most show commands (in any mode) display information for the current context only or, depending on the command syntax, for all contexts. If you are an administrator for the local context, you can insert the optional context ctx-name construct, preceding the show command, to view output for the specified context without entering that context. For more information about using the context ctx-name construct, see the context command description.

Note:  
By appending a space followed by the pipe ( | ) character at the end of a show command, you can filter the output using a set of modifier keywords and arguments. For more information, see “Modifying Output of show Commands” in Using the CLI.

1.20.6   Examples

The following example shows how to display 802.1Q PVCs on port 1 in slot 13:

[local]Redback>show dot1q pvc 13/1
Circuit                             State Profile         Bound to

13/1 vlan-id 1                      Up                    vlan1@local

The following example shows how to display a summary of all 802.1Q PVCs in all contexts:

[local]Redback#show dot1q pvc summary all
PVCs total: 1, Up: 1, Down: 0, Bound: 0

The following example shows how to display detailed information all 802.1Q PVCs:

[local]Redback#show dot1q pvc detail

Circuit        : 5/1 vlan-id 700:201 Bindings       : gig700.201@local

State          : Up              Description        :

Encapsulation  : dot1q           Profile            :

Agent Circuit ID:

QOS Hierarchical Mode: wrr

QOS Max Rate   : 91000

QOS Min Rate   : 50000

QOS Policing   : peanut acl-counters

QOS Queuing    : sony


Circuit        : 5/1 vlan-id 700:202 Bindings       : gig700.202@local

State          : Up              Description        :

Encapsulation  : dot1q           Profile            :

Agent Circuit ID:

QOS Hierarchical Mode: strict

QOS Weight     : 40

QOS Policing   : butter inherit acl-counters

QOS Metering   : science inherit acl-counters

QOS Queuing    : sony

The following example shows how to get information on PVCs in the lg-vlans link-group:

[local]Redback(config)#show dot1q pvc link-group lg-vlans

The following example shows how to display the information for the on-demand 802.1Q PVC connected to port/slot 5/1:

[local]Redback>show dot1q pvc on-demand range 5/1

Port  Vlan        through Vlan

5/1   1           through 2

5/1   3           through 3

C-VLANs: 0; S-VLANs: 0; VLANs: 3; Total: 3

1.21   show dot1q pvc transport

show dot1q pvc transport

1.21.1   Purpose

Displays information for all transport-enabled 802.1Q permanent virtual circuits (PVCs).

1.21.2   Command Mode

all modes

1.21.3   Syntax Description

1.21.4   Default

None

1.21.5   Usage Guidelines

Use the show dot1q pvc transport command to display information about all transport-enabled 802.1Q PVCs.

Note:  
By default, most show commands (in any mode) display information for the current context only or, depending on the command syntax, for all contexts. If you are an administrator for the local context, you can insert the optional context ctx-name construct, preceding the show command, to view output for the specified context without entering that context. For more information about using the context ctx-name construct, see the context command description.

Note:  
By appending a space followed by the pipe ( | ) character at the end of a show command, you can filter the output using a set of modifier keywords and arguments. For more information, see “Modifying Output of show Commands” in Using the CLI.

1.21.6   Examples

The following example shows how to display information about all transport-enabled 802.1Q PVCs connected to the SmartEdge router :

[local]Redback>show dot1q pvc transport


TSP-ID         : 5/1    any        Range End      :

Profile        : ---               Description    :

Binding        : ---               State          : Down

1.22   show dvsr

show dvsr [ip-addr/prefix-length | detail | profile | summary] [all]

1.22.1   Purpose

Displays information about all dynamically verified static routing (DVSR) routes.

1.22.2   Command Mode

all modes

1.22.3   Syntax Description

ip-addr/prefix-length

Optional. Displays the DVSR routes that match the IP address, in the form A.B.C.D, and the prefix length, separated by the slash (/) character. The range of values for the prefix-length argument is 0 to 32.

detail

Optional. Displays detailed DVSR route information.

profile

Optional. Displays DVSR profile information.

summary

Optional. Displays a summary report on DVSR routes in all contexts.

all

Optional. Displays DVSR information for all contexts.

1.22.4   Default

All DVSR routes in the current context are displayed.

1.22.5   Usage Guidelines

Use the show dvsr command to display information about all DVSR routes.

Use the optional keywords to display specific DVSR routes, DVSR profiles, detailed DVSR route information, and summary reports.

Note:  
By default, most show commands (in any mode) display information for the current context only or, depending on the command syntax, for all contexts. If you are an administrator for the local context, you can insert the optional context ctx-name construct, preceding the show command, to view output for the specified context without entering that context. For more information about using the context ctx-name construct, see the context command description.

Note:  
By appending a space followed by the pipe ( | ) character at the end of a show command, you can filter the output using a set of modifier keywords and arguments. For more information, see “Modifying Output of show Commands” in Using the CLI.

Table 7 describes the show dvsr command output fields.

Table 7    Field Descriptions for the show dvsr Command Output

Field

Description

DVSR route

IP address and prefix length of the static route.

S

State of the DVSR, either Up or Down.

Verify Addr

IP address that the DVSR route should verify.

Count

Number of verification successes (or failures) since the DVSR state change.

Delay

Average round trip and processing delay of the verification.

Tran

Number of state transitions for the DVSR route.

Seq

Internal sequence number for the DVSR route.

profile

Name of the DVSR profile for the DVSR route.

Table 8 describes the show dvsr profile command output fields.

Table 8    Field Descriptions for the show dvsr profile Command Output

Field

Description

DVSR profile

Name of the DVSR profile.

Num

Number of DVSR routes associated with this profile.

Intv

Verification interval in seconds of the profile.

F

Timeout multiplier value of the profile.

S

Minimum success value of the profile.

Next

Number of seconds for the next verification process for this profile to start.

TTL

Time-to-live value of the profile.

DIST

Distance value of the profile.

TAG

Tag value of the profile.

Src Addr

Source address of the profile.

1.22.6   Examples

The following example displays all DVSR routes:

[local]Redback>show dvsr
DVSR route         S  Verify Addr     Count  Delay Tran Seq  profile

11.12.0.0/16       Up 10.14.100.2     172    305   1    513  find-dopey

12.12.12.12/32     Up 10.14.101.2     172    309   1    714  find-dopey

12.1.1.0/24        Dn 10.14.100.4     12     0     2    514  black

12.1.2.0/24        Up 10.14.100.7     171    7     1    515  black



Total DVSR prefixes in context local: 4


The following example displays all DVSR profiles:

[local]Redback>show dvsr profile
DVSR profile         Num Intv F   S   Next TTL DIST TAG      Src Addr

nice                 12  20   3   2   12   5   1    0        

good                 3   20   3   2   7    5   1    0        



Total DVSR profiles in context local: 2


The following example displays the DVSR summary report:

[local]Redback>show dvsr summary
DVSR summary:



dvsr profiles: 4                    dvsr routes: 5

routes alive: 5                     routes fail: 0

total ping sent: 122                total recv icmp replies: 122

total icmp timeout: 0               total icmp no reply: 0

total reply no route: 0             total nexthop invalid: 2

avg round trip delay(msec): 0       max round trip delay(msec): 80

avg ping time(msec): 0              max ping time(msec): 80

total ping operation: 73            total ping error: 0

total route state changes: 5        max pings in a batch: 2

1.23   show ethernet-cfm circuit

show ethernet-cfm circuit cct [level level]

1.23.1   Purpose

Displays the CFM information about a specified circuit or circuits or a bundle of link-group aggregated circuits.

1.23.2   Command Mode

exec (10)

1.23.3   Syntax Description

circuit cct

Link-group or VLAN-ID of the circuit for which CFM instance information is displayed. The syntax for the circuit argument is:

{lg lg-name | id lg-ID} | {slot/port [vlan-id vlan-id]}[level level]

level level

The level of the MD containing the specified circuit.

detail

Display detailed CFM information.

lg lg-name | id lg-ID

Specifies the link-group name or link-group ID for which circuit CFM information is displayed.

slot/port

Specifies the slot and port on the system for which circuit CFM information is displayed.

vlan-id vlan-id

Specifies the VLAN-ID of the circuit for which CFM information is displayed.

1.23.3.1   Default

no default

1.23.3.2   Usage Guidelines

Use this command to display the CFM information about a specified circuit or circuits or a bundle of link-group aggregated circuits.

1.23.3.3   Examples

The following example illustrates the usage of this of this command:

Example 1   show ethernet-cfm circuit Command

[local]jazz#show ethernet-cfm circuit 5/1 vlan 66 level 5

1.24   show ethernet-cfm database (domain)

show ethernet-cfm database instance-name domain domain-name [detail]

1.24.1   Purpose

Displays the CFM information about a specified maintenance domain (MD) in a specified CFM instance.

1.24.2   Command Mode

exec (10)

1.24.3   Syntax Description

instance-name

Name of a CFM instance in the SmartEdge router.

domain-name

The name of the MD which is configured in the CFM instance. If no domain-name is specified, the instance-name is used.

detail

Display detailed information.

1.24.4   Default

no default

1.24.5   Usage Guidelines

Use this command to display the CFM information about a specified MD in a specified CFM instance.

1.24.6   Examples

The following two examples illustrates the output fields of this command:

[local]Redback#show ethernet-cfm database UP-INSTANCE domain redback
DOMAIN NAME     : redback
-----------------
Level           : 2              Domain Id      : 1
Number of MAs   : 1              Number of MIPs : 1

[local]Redback#show ethernet-cfm database UP-INSTANCE domain redback detail
DOMAIN NAME     : redback
-----------------
Level           : 2              Domain Id      : 1
Number of MAs   : 1              Number of MIPs : 1
Group mac       : 01:80:c2:00:00:32

1.25   show ethernet-cfm database (instance-name)

instance-name

show ethernet-cfm database instance-name

1.25.1   Purpose

Displays information stored in the SmartEdge system’s CCM database for the specified CFM instance. Displays all the maintenance domains (MDs), their maintenance associations (MAs), their maintenance intermediate points (MIPs), and the maintenance end points (MEPs) for the maintenance associations (MAs).

1.25.2   Command Mode

exec (10)

1.25.3   Syntax Description

instance-name

Name of a CFM instance in the SmartEdge system.

1.25.4   Default

no default

1.25.5   Usage Guidelines

Use this command to display information stored in the SmartEdge system’s CCM database for the specified CFM instance. This command displays all the maintenance domains, their MAs, their MIPs, the MEPs for the MAs.

Table 9    Fields in the Output of show ethernet-cfm database command

Field Heading

Information provided by the field

DOMAIN NAME

Domain name associated with the specified SmartEdge CFM instance

Level

MD level

Domain Id

Index for the MD configured under the CFM instance

Number of MAs

Number of MAs in the MD

Number of MIPs

Number of MIPs in the MD

MA Name

Maintenance association name

Ccms

Contiuity check enabled/disabled

Ccm Interval

Interval between CCM PDUs

Number of local meps

For each MA: the number of local maintenance association endpoints (MEPs).

MA Id/MA Name/MD Id/Vlan Id/Status

For each MA:

  • Maintenance association ID

  • Maintenance association name

  • Maintenance domain ID in which MA is configured

  • ID of the 802.1Q VLAN instance corresponding to the MA

  • Status of the MA

MpId/Level/MAC Addr/MA Id/Vlan Id

For each MEP in the MA:

  • MEPID

  • MAC address of circuit interface or port bound to MEP

  • Maintenance association ID

  • ID of the 802.1Q VLAN circuit interface bound to the MEP

State\Direction\Circuit Type

For each MEP in the MA:

  • Connectivity status

  • Direction configured for the MEP

  • Circuit or port type bound to the MEP

Number of Remote MEPs:

Number of MEPs in the maintenance domain (MD) for which MEPIDs have been assigned, and which are bound to ports or circuits not in the SmartEdge system.

MpId/Level/MAC Addr/MA Id/Vlan Id

For each remote MEP in the MD:

  • MEPID

  • MAC address of circuit interface or port bound to MEP

  • Maintenance association ID

  • ID of the 802.1Q VLAN circuit interface bound to the MEP

State\Direction\Circuit Type

For each remote MEP in the MD:

  • Connectivity status

  • Direction configured for the MEP

  • Circuit or port type bound to the MEP

Number of MIPs

Number of maintenance association intermediate points (MIPs) in the current MD

MpId/Level/MAC Addr/MA Id/Vlan Id

For each MIP in the MD:

  • MEPID

  • MAC address of circuit interface or port bound to MEP

  • Maintenance association ID

  • ID of the 802.1Q VLAN circuit interface bound to the MEP

State\Direction\Circuit Type

For each remote MIP in the MD:

  • Connectivity status

  • Direction configured for the MEP

  • Circuit or port type bound to the MEP

1.25.6   Examples

The following example shows the output fields of this command. The Domain Id field represents the index for the maintenance domain configured under the CFM instance. The Index field reports the index of the MA configured under the MD:

[local]Redback#show ethernet-cfm database instance-2
DOMAIN NAME     : redback
-----------------
Level           : 5              Domain Id      : 3
Number of MAs   : 1              Number of MIPs : 0

MA Name : platform (Index : 3)
---------
Ccms    : Enabled                Ccm Interval   : 100 ms
Number of local meps : 1         Number of remote meps : 1
Local MEP Information:

MepId  Level  MacAddr            State  Dir  Defects  Circuit
--------------------------------------------------------------
101    5      00:30:88:02:7f:5e  Reset  Up   2        1/1 vlan-id 100
Remote MEP Information:
MepId  MacAddr            State
--------------------------------
100    00:00:00:00:00:00  None

The following example shows a CFM database instance in which a MIP has been configured:

[local]Redback#show ethernet-cfm database UP-INSTANCE
DOMAIN NAME     : redback
-----------------
Level           : 2              Domain Id      : 1
Number of MAs   : 1              Number of MIPs : 1

MIP Information:
MipId  Level  MacAddr            State  Dir  Circuit
----------------------------------------------------- 1      2      00:30:88:02:f3:22  Reset  Up   2/1 vlan-id 1
MA Name : platform (Index : 1)
---------
Ccms    : Enabled                Ccm Interval   : 1s
Number of local meps : 1         Number of remote meps : 1

Local MEP Information:
MepId  Level  MacAddr            State  Dir  Defects  Circuit
--------------------------------------------------------------
100    2      00:30:88:02:f3:24  Reset  Up   -        2/3 vlan-id 1

Remote MEP Information:
MepId  MacAddr            State
-------------------------------- 
101    00:30:88:12:3d:8f  OK

1.26   show ethernet-cfm database (ma)

show ethernet-cfm database instance-name domain domain-name ma ma-short-name [detail]

1.26.1   Purpose

Displays CFM information about a maintenance association (MA) in a specified CFM instance.

1.26.2   Command Mode

exec (10)

1.26.3   Syntax Description

instance-name

Name of a CFM instance in the SmartEdge system.

domain-name

The name of the MD which is configured in the CFM instance. If no domain-name is specified, the instance-name is used.

ma ma-short-name

The name of the MA.

detail

Display detailed information.

1.26.4   Default

no default

1.26.5   Usage Guidelines

Use this command to display CFM information about a maintenance association (MA) in a specified CFM instance.

1.26.6   Examples

The following example shows the output fields of this command. The Frame Loss field reports the setting entered for the MA by the frame-loss command:

[local]Redback#show ether data instance-1 domain redback ma platform detail

MA Name      : platform

Instance name: instance-1         Level         : 5

Domain name  : redback            Domain Id     : 2

MA-Index     : 2                  Flags         : 0

Ccms         : Enabled            Ccm Interval  : 100ms

Slot mask    : Ox1                Frame loss    : 0

Number of local meps : 1          Number of remote meps : 1

1.27   show ethernet-cfm database (mep)

show ethernet-cfm database instance-name domain domain-name ma ma-short-name mep mep-id [detail]

1.27.1   Purpose

Displays CFM information about local Maintenance Endpoints (MEPs) in a specified Maintenance Association (MA) in a specified CFM instance.

1.27.2   Command Mode

exec (10)

1.27.3   Syntax Description

instance-name

Name of a CFM instance in the SmartEdge system.

domain-name

The name of the MD which is configured in the CFM instance. If no domain-name is specified, the instance-name is used.

ma ma-short-name

The name of the MA. Displays summary of all MAs in the CFM instance if no MA name is specified.

mep mep-id

The ID of a local MEP. Reports specified MEP in the specified MA that is bound to a local circuit interface on the SmartEdge router.

detail

Display detailed information.

1.27.4   Default

no default

1.27.5   Usage Guidelines

Use this command to display CFM information about local Maintenance Endpoints (MEPs) in a specified Maintenance Association (MA) in a specified CFM instance.

Table 10    Abbreviations in the Output from show ethernet-cfm database (mep) command

Field

Description

Domain id

Index of MD configured under the CFM instance.

MA index

Index of the MA configured under the CFM instance.

Slotmask

The mask to reflect the physical slot on which the MEP is configured.

Ref counter

Number of circuits in the MEP (including the MEP circuit).

Xc/L2vpn

Reports if the MEP has a cross connection or L2VPN configured.

Linkgroup Id

The ID of the Link group configured under the MEP

Cct handle

The circuit handle (unique identifier in the SmartEdge system) for the circuit on which the local MEP is configured

Lg active cct

The circuit in the link group used to transmit CCMs.

State

FNG state of the MEP.

Mep Defects

Defect detected for the MEP, which could be a remote MEP defect, configuration error, and so on.

Highest Defect

The highest defect detected for the MEP.

Lbms

Displays if loopback message (LBM) is enabled in the MEP.

Ltms

Displays if link-trace message (LTM) is enabled in the MEP.

Lbms/Ltms in

Counters for the number of LTMs and LBMs received.

Ltms priority

Priority value of the LTMs sent out.

Lbms/Ltms dropped

Counter for the number of LTMs and LBMs dropped.

Lbms bad msdu

Counter for the number of LBMs received with incorrect field values.

Lbrs in/out

Counter for the number of LBRs received and sent out.

Lbrs OutOfOrder

Counter for the number of LBRs received out of order.

Lbrs bad msdu

Counter for the number of LBRs received with incorrect field values.

1.27.6   Examples

The following example shows the output fields of this command.

Example 2   Detailed Output of show ethernet-cfm... Linktrace Output

[local]Redback#show ethernet-cfm database up domain dd ma platform mep 101 linktrace detail
-------------------------------------------------------------------
SequenceNumber: 32                          ReceiveOrder   : 1
-------------------------------------------------------------------
Ttl                    : 63                      Forwarded : No
TerminalMep            : No                   Relay Action : RlyMpDB
LastEgressId           : 00:00:00:30:88:13:07:8f
NextEgressId           : 00:00:00:00:00:00:00:00
ChassisId Subtype      : NetworkAddress
ChassisId              : 01 0a 0d 0b 1e
ManAddressDomain       : snmpOther
ManAddress             : 0 0 0 0 0
IngressMac             : 00:30:88:01:a0:74  Ingress Action : IngOk
IngressPortIdSubtype   : Local
IngressPortId          : 9/5:1023:63/1/2/18
EgressMac              : 00:00:00:00:00:00   Egress Action : IngNoTlv

1.28   show ethernet-cfm database (mip)

show ethernet-cfm database instance-name domain domain-name mip [mip-id] [detail]

1.28.1   Purpose

Displays CFM information about maintenance intermediate points (MIPs) in a specified CFM instance.

1.28.2   Command Mode

exec (10)

1.28.3   Syntax Description

instance-name

Name of a CFM instance in the SmartEdge router.

domain-name

The name of the MD which is configured in the CFM instance. If no domain-name is specified, the instance-name is used.

mip mip-id

The MIP ID. If no mip-id argument is specified, all MIPs in the CFM instance are displayed.

detail

Display detailed information.

1.28.4   Default

no default

1.28.5   Usage Guidelines

Use this command to display the CFM information about MIPs in a specified CFM instance.

Table 11    Abbreviations in the Output from show ethernet-cfm database (mip) command

Abbreviation

Description

Slotmask

The mask to reflect the physical slot on which the MIP is configured.

Ref counter

Number of circuits in the MIP (including the MIP circuit).

Xc/L2vpn

Reports if the MIP has a cross connection or L2VPN configured.

Linkgroup Id

The ID of the Link group configured under the MIP.

Cct handle

The circuit handle (unique identifier in the SmartEdge system) for the circuit on which the local MIP is configured.

Lg active cct

The circuit in the link group used to transmit CCMs.

Active cct handle

The circuit handle (unique identifier in the SmartEdge system) for the circuit in the link group used to transmit CCMs.

Lbms in

Loopback message (LBM) received.

Ltms in

Link-trace message (LTM) received.

1.28.6   Examples

The following example shows the output fields of this command:

[local]Redback#show ether data UP-INSTANCE domain redback mip 1 detail

MipId          : 1


Instance name  : UP-INSTANCE             Level            : 2

Domain name    : redback                 Domain id        : 1

Slotmask       : Ox0                     Ref counter      : 2

Xc/L2vpn       : Yes                     Linkgroup Id     : 0

Circuit        : 2/1 vlan-id 1           Cct handle       : 2/1:1023:63/1/2/6

Lg active cct  : -                       Active cct handle: -

MacAddr        : 00:30:88:02:f3:22


Lbms in        : 0                       Lbms out         : 0

Lbrs in        : 0                       Lbrs out         : 0

Ltms in        : 0                       Ltms out         : 0

Ltrs in        : 0                       Ltrs out         : 0

Lbms dropped   : 0                       Lbms bad msdu    : 0

Lbrs OutOfOrder: 0                       Lbrs bad msdu    : 0

Ltms dropped   : 0                       Ltrs dropped     : 0

Ltrs UnexpIn   : 0

1.29   show ethernet-cfm database (rmep)

show ethernet-cfm database instance-name domain domain-name ma ma-short-name rmep rmep-id [detail]

1.29.1   Purpose

Displays CFM information about local Remote Maintenance Endpoints (RMEPs) in a specified Maintenance Association (MA) in a specified CFM instance.

1.29.2   Command Mode

exec (10)

1.29.3   Syntax Description

instance-name

Name of a CFM instance in the SmartEdge router.

domain-name

The name of the MD which is configured in the CFM instance. If no domain-name is specified, the instance-name is used.

ma ma-short-name

The name of the MA. Displays summary of all MAs in the CFM instance if no MA name is specified.

rmep rmep-id

The ID of a remote MEP. Reports specified MEP in the specified MA that is bound to another network node.

detail

Display detailed information.

1.29.4   Default

no default

1.29.5   Usage Guidelines

Use this command to display CFM information about Remote Maintenance Endpoints (RMEPs) in a specified MA in a specified CFM instance.

1.29.6   Examples

The following example shows the output fields of this command:

[[local]Redback#show ether data instance-1 domain redback ma platform rmep 101 detail

Remote MepId : 101


Instance name: instance-1         Level       : 5

Domain name  : redback            Domain id   : 2

MA name      : platform           MA index    : 2

State        : OK                 Mac addr    : 00:30:88:02:7f:5e

1.30   show ext-community-list

show ext-community-list [ecl-name | first-match ecl-name ext-community-num | summary]

1.30.1   Purpose

Displays information about configured Border Gateway Protocol (BGP) extended community lists.

1.30.2   Command Mode

all modes

1.30.3   Syntax Description

ecl-name

Optional. Extended community list name.

first-match

Optional. Searches for the first match in the extended community list specified by the ecl-name argument.

ext-community-num

Extended community list number for the list in which the ecl-name first match is attempted.

The extended community number can be specified only when configuring an extended community list. It can be expressed in either of the following formats:

  • tt:asn:nnnn, where tt is the extended community type, asn is the ASN, and nnnn is a 32-bit integer. The extended community type identifies either a target or origin community. The target community identifies the destination to which the route is going, and the origin community identifies source from where the route originated. The tt argument is a placeholder for either the ro (route origin) keyword, or the rt (route target) keyword.

  • tt:ip-addr:nn, where tt is the extended community type, ip-addr is the IP address in the form A.B.C.D, and nn is a 16-bit integer.

summary

Optional. Displays extended community list summary information.

1.30.4   Default

Displays all configured extended community lists.

1.30.5   Usage Guidelines

Use the show ext-community-list command to display information about configured BGP extended community lists.

Note:  
By default, most show commands (in any mode) display information for the current context only or, depending on the command syntax, for all contexts. If you are an administrator for the local context, you can insert the optional context ctx-name construct, preceding the show command, to view output for the specified context without entering that context. For more information about using the context ctx-name construct, see the context command description.

Note:  
By appending a space followed by the pipe ( | ) character at the end of a show command, you can filter the output using a set of modifier keywords and arguments. For more information, see “Modifying Output of show Commands” in Using the CLI.

1.30.6   Examples

The following example displays two extended community lists (1 and 2):

[local]Redback>show ext-community-list
ext-community-list ext-comm-list01:

 count: 1, sequences: 10 - 10, client count: 1

 modified: 4 day(s), 17 hour(s) ago

   seq 10 permit RT:100:100   (hits: 0,  cache hits: 0)

   seq 20 permit RT:100:200   (hits: 2,  cache hits: 1)

ext-community-list ext-comm-list02:

 count: 4, sequences: 30 - 60, client count: 1

 modified: 4 day(s), 17 hour(s) ago

   seq 30 permit RO:10.10.10.1:3600  (hits: 0,  cache hits: 0)

   seq 40 permit RO:20.20.20.1:22  (hits: 0,  cache hits: 0)

   seq 50 permit RT:11:121  (hits: 4,  cache hits: 2)

   seq 60 permit RT:11:102  (hits: 2223,  cache hits: 2217)

1.31   show flow admission-control profile

show flow admission-control profile {all | id profile-id | name profile-name}

1.31.1   Purpose

Displays details of one or all flow admission control (FAC) profiles on the current SmartEdge router.

1.31.2   Command Mode

1.31.3   Syntax Description

all

Displays abbreviated output for all FAC profiles on the current SmartEdge router .

id profile-id

ID of the FAC profile to be displayed.

name profile-name

Name of the FAC profile to be displayed.

1.31.4   Default

None

1.31.5   Usage Guidelines

Use the show flow admission-control profile command to display details of one or all FAC profiles on the current SmartEdge router.

Note:  
By default, most show commands (in any mode) display information for the current context only or, depending on the command syntax, for all contexts. If you are an administrator for the local context, you can insert the optional context ctx-name construct, preceding the show command, to view output for the specified context without entering that context. For more information about using the context ctx-name construct, see the context command description.

Note:  
By appending a space followed by the pipe ( | ) character at the end of a show command, you can filter the output using a set of modifier keywords and arguments. For more information, see “Modifying Output of show Commands” in Using the CLI.

1.31.6   Examples

The following example shows how to display all FAC profiles:

[local]Redback(config)#show flow admission-control profile all



Name	Id

---------------------------------------------------- ----------

f1	0x40500001

f2	0x40500002

f3	0x40500003

The following example shows how to display information for a FAC profile with the ID 0x40500001:

[local]Redback(config)#show flow admission-control profile id 0x40500001



Name                                                   Id

---------------------------------------------------------------

f1                                                      0x40500001

The following example shows how to display information for a FAC profile with the name f1:

[local]Redback(config)#show flow admission-control profile name f1



Name                                                   Id

---------------------------------------------------------------

f1                                                      0x40500001

1.32   show flow circuit

show flow circuit {all | circuit-id}

1.32.1   Purpose

Displays FAC profile IDs for all circuits on the current SmartEdge router

1.32.2   Command Mode

1.32.3   Syntax Description

all

Optional. Displays the FAC profile IDs for all circuits.

circuit circuit-id

Optional. ID of an 802.1Q permanent virtual circuit (PVC).

1.32.4   Default

None

1.32.5   Usage Guidelines

Use the show flow circuit command to display FAC profile IDs for all circuits on the current SmartEdge router

Note:  
By default, most show commands (in any mode) display information for the current context only or, depending on the command syntax, for all contexts. If you are an administrator for the local context, you can insert the optional context ctx-name construct, preceding the show command, to view output for the specified context without entering that context. For more information about using the context ctx-name construct, see the context command description.

Note:  
By appending a space followed by the pipe ( | ) character at the end of a show command, you can filter the output using a set of modifier keywords and arguments. For more information, see “Modifying Output of show Commands” in Using the CLI.

1.32.6   Examples

The following example shows how to display FAC details for all circuits that have a FAC profile applied:

[local]Redback(config)#show flow circuit all



Circuit               FAC Id        Dir     FAC Id        Dir

----------------------------------------------------------

1/1:1023:63/1/2/6			     0x40500002    OUT

1/1:1023:63/1/2/8    0x40500003    IN

1/1:1023:63/1/2/245750x40500003    BIDIR

1.33   show flow collector

show flow collector [collector-name [statistics]]

1.33.1   Purpose

Displays information related to an external collector.

1.33.2   Command Mode

all modes

1.33.3   Syntax Description

collector-name

Identifies an external collector.

statistics

Displays statistical information for the specified external collector.

1.33.4   Default

Enter the show flow collector command without the optional argument or keyword to display a list of all external collectors configured in the current context.

1.33.5   Usage Guidelines

Use the show flow collector command to display information related to an external collector.

Table 12 describes the show flow collector command output for all external collectors configured in the current context.

Table 12    show flow collector Command Output Descriptions (All Collectors)

Field

Description

Collector

Identifies the external collector for which information is displayed.

Identifier

External collector identifier in hexadecimal format. A hexadecimal identifier is internally created when you create a new collector and is mapped to the collector. The hexadecimal identifier is used primarily for debugging purposes.

IP Address

Destination address for the external collector where exported packets are received. Use the ip address command in flow collector configuration mode to specify an IP address for an external collector.

Port

Port on the external collector that receives exported packets. This is the port that listens for flow records from the SmartEdge router. Use the port command in flow collector configuration mode to configure or modify the destination port for an external collector.

Table 13 describes the show flow collector command output for a specific external collector.

Table 13    show flow collector Command Output Descriptions (Specific Collector)

Field

Description

Collector

Identifies the external collector for which information is displayed.

Identifier

External collector identifier in hexadecimal format. A hexadecimal identifier is internally created when you create a new external collector and is mapped to the external collector. The hexadecimal identifier is used primarily for debugging purposes.

Context

Context that hosts the specified external collector.

Source IP

Source ip address from which packets are sent to the external collector. If the source IP address was set to zero, then the ip-address of the outgoing interface will be used.

Destination IP

Destination address for the external collector where exported packets are received. Use the ip address command in flow collector configuration mode to specify an IP address for an external collector.

Destination port

Port on the external collector that receives exported packets. This is the port that listens for flow records from the SmartEdge router. Use the port command in flow collector configuration mode to configure or modify the destination port for an external collector.

Transport protocol

Protocol used for transporting flow records. User Datagram Protocol (UDP) is the only supported protocol in this release.

Export version

Export version that determines the fields included in the flow record. In this release, only Export version 5 is supported.

Profile

Identifies an RFlow profile that is attached to the specified external collector. A single external collector can have multiple RFlow profiles attached to it. You can configure up to 10 profiles on a single external collector.

1.33.6   Examples

The following example displays summarized information about all external collectors configured in the current context:

[local]Redback#show flow collector



Collector            Identifier IP Address         Port

---------            ---------- ----------         ----

c1                   0x2        10.13.168.77       5000

The following example displays information about all external collectors configured on the router:

[local]Redback#show flow collector c1



Collector          : c1

Identifier         : 0x2

Context            : local

Source IP          : 10.13.168.70

Destination IP     : 10.13.168.77

Destination port   : 5000

Transport protocol : udp 

Export version     : v5 

Profile            : p1

1.34   show flow counters

show flow counters [{detail | debug | clear}]

1.34.1   Purpose

Displays settings for common flow admission control (FAC) counters.

1.34.2   Command Mode

1.34.3   Syntax Description

detail

Optional. Displays FAC counters.

debug

Optional. Displays debug information for FAC counters.

clear

Optional. Clears FAC counters after displaying them.

1.34.4   Default

None

1.34.5   Usage Guidelines

Use the show flow counters command to display FAC counters

Note:  
By default, most show commands (in any mode) display information for the current context only or, depending on the command syntax, for all contexts. If you are an administrator for the local context, you can insert the optional context ctx-name construct, preceding the show command, to view output for the specified context without entering that context. For more information about using the context ctx-name construct, see the context command description.

Note:  
By appending a space followed by the pipe ( | ) character at the end of a show command, you can filter the output using a set of modifier keywords and arguments. For more information, see “Modifying Output of show Commands” in Using the CLI.

1.34.6   Examples

The following example shows how to display summary information for FAC counters:

[local]Redback(config)#show flow counters



Current time: Mon Apr 30 17:51:37 2007

Last cleared: Never

FAC Profile------------------------------------

Create4Apply3

Delete0UnApply0

FAC Profile Current----------------------------

FAC Profs4Applied Ccts3 

The following example shows how to display detailed information for FAC counters:

[local]Redback(config)#show flow counters detail



Tree Failures----------------------------------------------------

No Memory 				0		No Room in Table			0

ISM Msgs Ignored-------------------------------------------------

Unknown Event 				0		Port State Ign			3

Cct State No Cct				 0		Cct State Ign			6

Cct Cfg No Cct				0		Total Ignored		9

Flow Application------------------------------	-------------------

RCM Apply			3		AAA Apply				0

RCM UnApply			0		AAA UnApply			0

RCM Appl Ignored			0		AAA Appl Ignored			0

RCM UnAppl Ignor			0		AAA UnAppl Ignor			0

Apply Conflict		0		UnApply Conflict			0

UnApply No Cct		0

FAC Cct Adds	3		FAC Cct Dels			0

FAC Application Current------------------------------------------

RCM Applied Ccts		3		AAA Applied Ccts			0 

The following example shows how to display debug information for FAC counters:

[local]Redback(config)#show flow counters debug



Current time: Sat Jun 18 08:37:22 2007

Last cleared: Never

IPC----------------------------------------------

IPCs from ISM	4	Msgs from ISM	6

IPCs from RCM	8

IPCs from PPAs	0

PPA----------------------------------------------

Births	2	Deaths	0

RCM----------------------------------------------

	Births	3	Deaths	2

	IPC in Rejected	0

ISM----------------------------------------------

	Births	1	Deaths	0

	EOF	1	MBE All EOF	1

ISM In-------------------------------------------



	ISM Statistics

	Total events: ipc rcvd: 0, ipc err 0, unknown event 0

	ID: 	I/F	:state 0, cfg 0, IP cfg 0,

		Cct	:state 2, Cct cfg 1, Cct grp 0

		Port	:state 1, Port cfg 0

		Lg	:cfg 0

		L2tp	:sesscfg 0

		Hdr	:only 2

		GrpMac	:cfg 0

Card :state 0

The following example shows how to display FAC counters and then clears them:

[local]Redback(config)#show flow counters clear



Current time: Mon Jun 27 09:45:27 2007

Last cleared: Never



FAC Profile-------------------------------------------------

		Create		3		 Apply		1

		Delete		0		Unapply		0

FAC Profile Current-----------------------------------------

	FAC Profs			3		Applied Ccts		1

1.35   show flow ip

show flow ip [show-flow-ip-arguments]

1.35.1   Purpose

Shows IP flow accounting information.

1.35.2   Command Mode

all modes

1.35.3   Syntax Description

You can replace show-flow-ip-arguments with the following keywords:

application-list

Displays information on application lists.

cache

Displays cache information.

circuit

Displays information on circuits.

log

Displays IPFIX logging information.

profile

Displays profile information.

1.35.4   Default

If you have configured one profile, the show flow ip command displays the following output:

[local]Redback# show flow ip
Number of Profiles        : 1
Number of Circuits        : 0
Number of Collectors      : 0
Number of Caches          : 0
Sampling Interval         : 1
[local]Redback# 

In the output, the Samping Interval is 1 (the default value). The rest of the fields are reported based on configuration.

1.35.5   Usage Guidelines

Use the show flow ip command to display information on RFlow profiles, circuits, collectors, caches, and the sampling interval. Table 14 describes the show flow ip command output:

Table 14    show flow ip Command Output Descriptions

Field

Description

Number of Profiles

Displays number of configured RFlow profiles.

Number of Circuits

Displays number of RFlow circuits.

Number of Collectors

Displays number of configured RFlow collectors in the system

Number of Caches

Displays number of RFlow caches created in the system.

Sampling Interval

Displays configured sampling packet interval.

1.35.6   Examples

The following example displays information on the number of profiles, circuits, collectors, caches, and the packet sampling interval:

[local]Redback# show flow ip

Number of Profiles        : 4
Number of Circuits        : 2
Number of Collectors      : 1
Number of Caches          : 2
Sampling Interval         : 1

1.36   show flow ip application-list

show flow ip application-list [appl-list-name]

1.36.1   Purpose

Displays the configured application lists.

1.36.2   Command Mode

all modes

1.36.3   Syntax Description

appl-list-name

Name of an application list.

1.36.4   Default

Displays the names of all the application lists configured on the system, including the system default application list,_sys_dflt_app_list_.

1.36.5   Usage Guidelines

Use the show flow ip application-list command to view the list of configured application lists and their contents.

1.36.6   Examples

The following example displays the contents of the system default application list, _sys_dflt_app_list_:

[local]Redback# show flow ip application-list _sys_dflt_app_list_

application-list _sys_dflt_app_list_
 application TCP-Telnet
  protocol tcp port 23
 application TCP-FTP
  protocol tcp port 21
 application TCP-FTPD
  protocol tcp port 20
 application TCP-HTTP
  protocol tcp port 80
 application TCP-SMTP
  protocol tcp port 25
 application TCP-BGP
  protocol tcp port 179
 application TCP-NNTP
  protocol tcp port 119
 application TCP-Other
  protocol tcp
 application UDP-DNS
  protocol udp port 53
 application UDP-NTP
  protocol udp port 123
 application UDP-TFTP
  protocol udp port 69
 application UDP-Other
  protocol udp
 application ICMP
  protocol icmp
 application IGMP
  protocol igmp

The show flow ip application-list command displays the configured values. For more information, see the flow ip application-list command.

1.37   show flow ip cache

show flow ip cache [ profile-name {dump | statistics [application ] | top-talkers [number [sort-by {packets | bytes } | all-context]

1.37.1   Purpose

Displays a list of all RFlow caches currently configured on the router, or detailed information about a specific RFlow cache.

1.37.2   Command Mode

all modes

1.37.3   Syntax Description

profile-name

Profile hosting the cache or caches of information that you want to display.

dump

Displays the entire contents of the specified cache.

statistics

Displays statistical information for all the flow records in the specified cache.

application

Displays statistics related to your application protocols in a specified cache.

top-talkers

Displays information about the largest packet and byte consumers in the network.

number

Displays the specified range, between 1 and 20, of items to display in the top-talkers output list.

sort-by packets or byte

Displays information based on your sort criteria for top-talkers, whether top-talkers are determined by number of packets or number of bytes.

all-context

Displays the names of all profile caches in all contexts. The all-context keyword is available in the local context only.

1.37.4   Default

Enter the show flow ip cache without any of the optional arguments or keywords to display summarized information for all RFlow caches in the current context.

1.37.5   Usage Guidelines

Use the show flow ip cache command to display a list of all RFlow caches currently configured on the router, or to display detailed information about a specific RFlow cache.

Note:  
On the XCRP, flows received from the PPA are directed to a cache. There is one cache for each profile in a context. If the same profile is attached to different circuits in multiple contexts, that profile has a different, unique cache in each context.

Table 15 describes the show flow ip cache command output.

Table 15    show flow ip cache Command Field Descriptions (All Caches)

Field

Description

Profile

Identifies an RFlow profile associated with this cache.

Max Size

Number of entries allowed in the cache before they are aged (sent to an external collector).

Usage

Amount of the cache used at the time the show flow ip cache command is executed. The display shows the number of resource entries currently in the cache.

Table 16 describes the show flow ip cache all-context command output.

Table 16    show flow ip cache all-context Command Output Descriptions

Field

Description

Profile

Identifies an RFlow profile associated with this cache.

Max Size

Number of entries allowed in the cache before they are aged (sent to an external collector).

Usage

Amount of the cache used at the time the show flow ip cache command is executed. The display shows the number of resource entries currently in the cache.

Context

Identifies the context of the cache.

Table 17 describes the show flow ip cache statistics command output.

Table 17    show flow ip cache statistics Command Output Descriptions

Field

Description

Profile

Identifies the RFlow profile for which information is displayed.

Context

Identifies the context that hosts the specified profile.

Statistics

Displays statistics for the following cache counters:

  • PPA flows received—Total number of PPA flows received by this cache.

  • PPA flows processed—Total number of PPA flows processed (transmitted) by this cache.

  • PPA flows discarded—Total number of PPA flows discarded by this cache due to a processing error.

  • Processing errors—Total number of flow processing errors that occurred on this cache.

  • Cache entries created—Total number of entries created by this cache.

  • Cache entries updated—Total number of entries updated in the cache to accurately reflect changes in the cache.

  • Cache entries aged—Total number of entries that were aged (exported) from this cache.

  • Cache entries fast-aged—Total number of entries that were fast-aged out of the cache. Entries are fast-aged when the maximum limit of the cache has been reached, a counter overflows, or a cache is deleted.

  • Entries in cache—Total number of flow entries currently in the cache.

  • Ager walks—Total number of times the flow ager was run on the cache.

The cache statistics counters are not resilient and are initialized to 0 after a process restart.

Collector Stream Information

Displays the following stream statistic counters for the specified external collectors:

  • Collector—Identifies the external collector for which stream statistics are displayed.

  • ExportID— Identifies the flow record that was exported to an external collector. This identifier increments each time a new record is exported. If the ExportID is reset to zero after a restart or switchover, an error has occurred and you need to troubleshoot the problem.

  • Seq Number—Incremental sequence counter of all export packets sent from the current observation domain by the exporter. This value is cumulative and is used by the external collector to identify whether any export packets have been missed.

  • Packets Exported—Total number of packets exported by this external collector.

  • Packets Dropped—Total number of packets dropped by this external collector due to an error.

  • Records Exported—Total number of records exported by this external collector.

  • Records Dropped—Total number of records dropped by this external collector due to an error.

All stream statistic counters are resilient except ExportID. The ExportID counter is reset to 0 after a restart or switchover, indicating that an error has occurred in RFlow.

Table 18 describes the show flow ip cache statistics application command output.

Table 18    show flow ip cache statistics application Command Output Descriptions

Field

Description

Total Flows

Number of flows in the cache for this application since the last time the statistics were cleared.

Flows/Sec

Average number of flows per second for this application.

Packets/Flow

Average number of packets per flow for this application.

Bytes/Pkt

Average number of bytes per packet for this application.

Packets/Sec

Average number of packets per second for this application.

Active(Sec)/Flow

Average number of seconds that a flow was active for this application before it was expired.

Idle(Sec)/Flow

Average number of seconds that a flow was idle for this application before it was expired.

1.37.6   Examples

The following example displays summary information for all RFlow caches in the current context:

[local]Redback#show flow ip cache 



Profile              Max Size   Usage

-------              --------   -----

p1                   4096       0

The following example displays information about all caches configured on the router:

[local]Redback#show flow ip cache all-context

Profile              Max Size   Usage      Context

-------              --------   -----      -------

p1                   4096       0          local

p1                   4096       0          rflow

The following example displays statistical information for the cache called p1:

[local]Redback#show flow ip cache p1 statistics



Profile : p1

Context : local

Statistics:

PPA flows received     : 0

PPA flows processed    : 0

PPA flows discarded    : 0

Processing errors      : 0

Cache entries created  : 0

Cache entries updated  : 0

Cache entries aged     : 0

Cache entries fast-aged: 0

Entries in cache       : 0

 Ager walks             : 0

Collector Stream Information:

Collector   ExportID Seq Number     Generated            Send Errors

                                  Packets  Records    Packets   Records

---------   -------- ----------    -------- ---------- --------- -------

c1           1        0x4          2        4          0         0 

The following example displays statistical information on flow records for application protocols gathered per cache since the last time it was cleared. To look for information on a specific application, use the output modifier and grep for information on that specific application.

[local]Redback#show flow ip cache p1 statistics application


Last cleared: Thu Aug 13 18:57:22 2009
Current time: Thu Aug 13 19:12:57 2009

Application        Total    Flows   Packets Bytes  Packets Active(Sec) Idle(Sec)
-----------        Flows     /Sec     /Flow  /Pkt     /Sec      /Flow     /Flow
TCP-Telnet             0      0.0         0     0      0.0        0.0       0.0
TCP-FTP                0      0.0         0     0      0.0        0.0       0.0
TCP-FTPD               0      0.0         0     0      0.0        0.0       0.0
TCP-HTTP               0      0.0         0     0      0.0        0.0       0.0
TCP-SMTP               0      0.0         0     0      0.0        0.0       0.0
TCP-BGP                0      0.0         0     0      0.0        0.0       0.0
TCP-NNTP               0      0.0         0     0      0.0        0.0       0.0
TCP-Other              6      0.0     46666  1200    299.5        9.9      20.1
UDP-DNS                0      0.0         0     0      0.0        0.0       0.0
UDP-NTP                0      0.0         0     0      0.0        0.0       0.0
UDP-TFTP               0      0.0         0     0      0.0        0.0       0.0
UDP-Other              0      0.0         0     0      0.0        0.0       0.0
ICMP                   0      0.0         0     0      0.0        0.0       0.0
IGMP                   0      0.0         0     0      0.0        0.0       0.0
Other                  0      0.0         0     0      0.0        0.0       0.0

1.38   show flow ip circuit

show flow ip circuit [circuit-id | all-context]

1.38.1   Purpose

Displays information about a specified IP circuit that has RFlow enabled.

1.38.2   Command Mode

all modes

1.38.3   Syntax Description

circuit-id

Optional. Circuit identifier.

Use the show flow circuit all command to display a list of all FAC profile IDs for all circuits on the current SmartEdge router.

all-context

Displays information about all circuits configured in all contexts. The all-context keyword is available in the local context only.

1.38.4   Default

Enter the command without the optional circuit-id argument to display brief information about all circuits in the current context that have RFlow enabled.

1.38.5   Usage Guidelines

Use the show flow ip circuit command to display information about a specified IP circuit that has RFlow enabled.

Table 19 describes the show flow ip circuit command output for all circuits.

Table 19    show flow ip circuit (All Circuits) Command Output Descriptions

Field

Description

Circuit

Identifies the circuit for which RFlow information is displayed.

Interface

Identifies the interface that is bound to the specified circuit.

Direction

Direction of the interface. Can be outgoing (egress), incoming (ingress), or both.

Profile

Identifies the profile that is currently applied to this circuit.

Table 20 describes the show flow ip circuit command output for a specific circuit.

Table 20    show flow ip circuit (Specific Circuit) Command Output Descriptions

Field

Description

Circuit

Identifies the circuit for which RFlow information is displayed.

Profile applied

Identifies the profile currently applied to this circuit.

Direction

Direction of the interface. Can be outgoing (egress), incoming (ingress), or both.

IPPA Statistics

Displays the current statistics from the following iPPA (ingress Packet Processing ASIC) counters:

  • Flows received by XCRP—Total number of flows received by the XCRP for a given circuit.

  • Flows dropped by XCRP—Total number of flows that were dropped by the XCRP due to errors.

  • Bytes bypassed flow infrastructure—Bytes bypassed because no resources were available to process flows.

  • Packets bypassed flow infrastructure—Total number of packets for which the PPA was unable to create a flow. Use this counter to track packets on a circuit that RFlow is unable to monitor.

  • Microflows aged out—Number of microwflows that were exported because the inactive or active timeout expired. When a new flow arrives on the PPA, the PPA creates a Flow Control Block (FCB). After the FCB is created, the flow is called a microflow. When a flow is expired (or aged) its corresponding FCB is deleted. The next packet with the same key fields starts a new a new microflow, so a new FCB is created.

  • Microflows not L1 aggregated—Total number of bytes that were not aggregated because the PPA could not add them to the L1 cache.

  • Bytes not L1 aggregated—Total number of microflows that were not aggregated because the PPA could not add them to the L1 cache.

  • Packets not L1 aggregated—Total number of packets that were not aggregated because the PPA could not add them to the L1 cache

  • Flows aged out of L1 cache—Total number of flows exported (aged) out of the L1 cache because the inactive or active timeout expired.

  • Flows not reported due to no buffer—Total number of received flows that the PPA did not report to the XCRP because the XCRP buffer was out of memory.

  • Bytes aggregated but not reported—Total number of aggregated bytes that the PPA did not report to the XCRP.

  • Packets aggregated but not reported—Total number of aggregated packets that the PPA did not report to the XCRP.

EPPA Statistics

Displays the current statistics from the following ePPA (egress Packet Processing ASIC) counters:

  • Flows received by XCRP—Total number of flows received by the XCRP for a given circuit.

  • Flows dropped by XCRP—Total number of flows dropped by the XCRP due to errors.

  • Bytes bypassed flow infrastructure—Total number of bytes for which the PPA was unable to create a flow. Use this counter to track packets on a circuit that RFlow is unable to monitor.

  • Packets bypassed flow infrastructure—Total number of packets for which the PPA was unable to create a flow. Use this counter to track packets on a circuit that RFlow is unable to monitor.

  • Microflows aged out—Number of Flow Control Blocks (FCBs) that the PPA added to the L1 aggregation cache because the inactive or active timeout expired. When a new flow arrives on the PPA, the PPA creates an FCB. After the FCB is created, the flow is called a microflow. When a flow is expired, its corresponding FCB is deleted. The next packet with the same key fields starts a new microflow and a new FCB.

  • Microflows not L1 aggregated—Total number of microflows that were not aggregated because the PPA could not add them to the L1 cache.

  • Bytes not L1 aggregated—Total number of microflows that were not aggregated because the PPA could not add them to the L1 cache.

  • Packets not L1 aggregated—Total number of packets that were not aggregated because the PPA could not add them to the L1 cache

  • Flows aged out of L1 cache—Total number of flows exported (aged) out of the L1 cache because the inactive or active timeout expired.

  • Flows not reported due to no buffer—Total number of received flows that the PPA did not report to the XCRP because the XCRP buffer was out of memory.

  • Bytes aggregated but not reported—Total number of aggregated bytes that the PPA did not report to the XCRP.

  • Packets aggregated but not reported—Total number of aggregated packets that the PPA did not report to the XCRP.

With the exception of the “Flows received by XCRP” and “Flows dropped by XCRP” counters, all counters are maintained on the PPA, which updates the counters once every 5 minutes. The “Flows received by XCRP” and “Flows dropped by XCRP” counters are maintained on the XCRP. As a result, there may be some inconsistencies between the “Flows received by the XCRP” counter and the “Flows aged out of L1 cache” counter if the PPA has not updated the “Flows aged out of L1 cache” counter yet.

1.38.6   Examples

The following example shows how to display RFlow information for all circuits in the current context that have RFlow enabled:



[local]Router#show flow ip circuit



Circuit                        Interface       Direction  Profile

-------                        ---------       ---------  -------

5/5:1023:63/1/2/10             egress          both       p1

The following example shows how to display RFlow information for the circuit with the handle 5/6:1023:63/1/2/8296

[local]Router#show flow ip circuit 5/6:1023:63/1/2/8296



Circuit         : 5/6 vlan-id 50

Profile applied : p1

Direction       : both

IPPA Statistics:

Flows received by XCRP                       : 10

Flows dropped by XCRP                        : 0

Bytes bypassed flow infrastructure           : 0

Packets bypassed flow infrastructure         : 0

Microflows aged out                          : 10

Microflows not L1 aggregated                 : 0

Bytes not L1 aggregated                      : 0

Packets not L1 aggregated                    : 0

Flows aged out of L1 cache                   : 10

Flows not reported due to no buffer          : 0

Bytes aggregated but not reported            : 0

Packets aggregated but not reported          : 0

EPPA Statistics:

Flows received by XCRP                       : 10

Flows dropped by XCRP                        : 0

Bytes bypassed flow infrastructure           : 0

Packets bypassed flow infrastructure         : 0

Microflows aged out                          : 10

Microflows not L1 aggregated                 : 0

Bytes not L1 aggregated                      : 0

Packets not L1 aggregated                    : 0

Flows aged out of L1 cache                   : 10

Flows not reported due to no buffer          : 0

Bytes aggregated but not reported            : 0

Packets aggregated but not reported          : 0

1.39   show flow ip log ism

show flow ip log ism [error | rx]

1.39.1   Purpose

Displays a log of all RFlow events on the SmartEdge router .

1.39.2   Command Mode

all modes

1.39.3   Syntax Description

ism

Displays Circuit State Manager (ISM) events only.

error

Displays error events only.

rx

Displays only those events received from ISM.

1.39.4   Default

Enter the show flow ip log command with no optional keywords to display a log of all RFlow events that occurred on the SmartEdge router.

1.39.5   Usage Guidelines

Use the show flow ip log command to display a log of all RFlow events that occurred on the SmartEdge router.

Table 21 describes the show flow ip log command output.

Table 21    show flow ip log Command Output Descriptions

Field

Description

Entry number

Number that identifies the individual event message.

month day hours:minutes:seconds

Date and time when the event occurred.

ISM RX rc

ISM return code.

IPFIX ISM Event:

Location where the event occurred, and type of event that occurred.

event

Description of the event that occurred.

cct_handle

The circuit where the event occurred.

port type

Type of port on which the event occurred, in hexadecimal format.

state

Current state of the port where the event occurred.

encaps

Port encapsulation type, expressed in hexadecimal format.

The encaps field is displayed for port configuration events only.

if index

Interface identifier, expressed in hexadecimal format.

The if index field is displayed for port configuration events only.

1.39.6   Examples

The following example shows how to display a log of all RFlow ISM events that have occurred on the router:

[local]Redback #show flow ip log ism



IPFIX<->ISM log messages (20 total entries):



0:  Jul 7 22:48:31 ISM RX rc: 0

IPFIX ISM Event: Port Config, event: PRT ethcfg

cct_handle: 5/5:1023:63/1/0/2 port type: 0xa

encaps: 0x1000000 if index: 0x1



1:  Jul 7 22:48:31 ISM RX rc: 0

IPFIX ISM Event: Port State, event: PRT up

cct_handle: 5/5:1023:63/1/0/2, state: Unknown



2:  Jul 7 22:48:31 ISM RX rc: 0

IPFIX ISM Event: Port Config, event: PRT ethcfg

cct_handle: 5/6:1023:63/1/0/4 port type: 0xa

encaps: 0x1000000 if index: 0x2



3:  Jul 7 22:48:31 ISM RX rc: 0

IPFIX ISM Event: Port State, event: PRT up

cct_handle: 5/6:1023:63/1/0/4, state: Unknown



4:  Jul 7 22:48:31 ISM RX rc: 0

IPFIX ISM Event: Port Config, event: PRT ethcfg

cct_handle: 5/8:1023:63/1/0/6 port type: 0xa

encaps: 0x1000000 if index: 0x3



5:  Jul 7 22:48:31 ISM RX rc: 0

IPFIX ISM Event: Port State, event: PRT up

cct_handle: 5/8:1023:63/1/0/6, state: Unknown



6:  Jul 7 22:48:31 ISM RX rc: 0

IPFIX ISM Event: Port Config, event: PRT ethcfg

cct_handle: 7/1:1023:63/1/0/8 port type: 0x10

encaps: 0x1000000 if index: 0x4



7:  Jul 7 22:48:31 ISM RX rc: 0

IPFIX ISM Event: Port State, event: PRT up

cct_handle: 7/1:1023:63/1/0/8, state: Unknown



8:  Jul 9 00:08:36 ISM RX rc: 0

IPFIX ISM Event: Port State, event: PRT down

cct_handle: 5/5:1023:63/1/0/2, state: DOWN



9:  Jul 9 00:08:36 ISM RX rc: 0

IPFIX ISM Event: Port State, event: PRT down

cct_handle: 5/6:1023:63/1/0/4, state: DOWN



10:  Jul 9 21:06:20 ISM RX rc: 0

IPFIX ISM Event: Port State, event: PRT down

cct_handle: 5/8:1023:63/1/0/6, state: DOWN



11:  Jul 9 21:06:23 ISM RX rc: 0

IPFIX ISM Event: Port State, event: PRT up

cct_handle: 5/8:1023:63/1/0/6, state: Unknown



12:  Jul 9 21:44:11 ISM RX rc: 0

IPFIX ISM Event: Port State, event: PRT down

cct_handle: 5/8:1023:63/1/0/6, state: DOWN



13:  Jul 9 21:44:14 ISM RX rc: 0

IPFIX ISM Event: Port State, event: PRT up

cct_handle: 5/8:1023:63/1/0/6, state: Unknown



14:  Jul 9 21:44:16 ISM RX rc: 0

IPFIX ISM Event: Port State, event: PRT down

cct_handle: 5/8:1023:63/1/0/6, state: DOWN



15:  Jul 9 21:44:21 ISM RX rc: 0

IPFIX ISM Event: Port State, event: PRT up

cct_handle: 5/8:1023:63/1/0/6, state: Unknown



16:  Jul 9 21:47:36 ISM RX rc: 0

IPFIX ISM Event: Port State, event: PRT down

cct_handle: 5/8:1023:63/1/0/6, state: DOWN



17:  Jul 9 21:47:59 ISM RX rc: 0

IPFIX ISM Event: Port State, event: PRT up

cct_handle: 5/8:1023:63/1/0/6, state: Unknown



18:  Jul 9 21:48:38 ISM RX rc: 0

IPFIX ISM Event: Port State, event: PRT down

cct_handle: 5/8:1023:63/1/0/6, state: DOWN



19:  Jul 9 21:49:19 ISM RX rc: 0

IPFIX ISM Event: Port State, event: PRT up

        cct_handle: 5/8:1023:63/1/0/6, state: Unknown


1.40   show flow ip profile

show flow ip profile [profile-name [circuits [all-context] | collectors [all-context]]

1.40.1   Purpose

Displays information about an RFlow profile.

1.40.2   Command Mode

all modes

1.40.3   Syntax Description

profile-name

Identifies the profile for which you want to display information.

circuits

Displays a list of circuits to which the specified profile is applied.

collectors

Displays a list of external collectors attached to the specified profile.

all-context

Displays profile information for all contexts currently configured on the router. If you do not include the all-context keyword, the command output displays profile information for the current context only.

1.40.4   Default

Enter the command without any of the optional keywords or arguments to display a list of all profiles configured in the current context.

1.40.5   Usage Guidelines

Use the show flow ip profile command to display information related to an RFlow profile.

Table 22 describes the show flow ip profile command output for all profiles.

Table 22    show flow ip profile Command Output Descriptions (All Profiles)

Field

Description

Profile

Identifies the RFlow profile for which information is displayed.

Identifier

RFlow profile identifier in hexadecimal format. The hexadecimal RFlow profile identifier is used for debugging.

Table 23 describes the show flow ip profile command output for a specific profile.

Table 23    show flow ip profile Command Output Descriptions (Specific Profile)

Field

Description

Profile

Identifies the RFlow profile for which information is displayed.

Identifier

RFlow profile identifier in hexadecimal format. The hexadecimal RFlow profile identifier is used for debugging purposes.

Active timeout

Timeout period, in seconds, after which a flow is considered complete (expired) and a flow record is created and exported to the external collector. Use the active timeout command in flow IP profile configuration mode to configure or modify the active timeout period.

Aggregation cache size

Number of entries that can be stored in the aggregation cache at one time. The aggregation cache size determines how much information is reported when you access the RFlow data. Use the aggregation-cache-size command in flow IP profile configuration mode to configure or modify the size of the aggregation cache.

1.40.6   Examples

The following example shows how to display a lists of all profiles configured in the current context:

[local]Redback #show flow ip profile



Identifier     Profile

-----------    -------

0x40800001     p1

The following example shows how to display information about a specific profile called p1:

[local]Redback #show flow ip profile p1

Profile                 : p1

Identifier              : 0x40800001

Active timeout          : 1800

 Aggregation cache size  : 4096

1.41   show flow log

show flow log

1.41.1   Purpose

Displays the log of all flow events on the current SmartEdge router.

1.41.2   Command Mode

1.41.3   Default

None

1.41.4   Usage Guidelines

Use the show flow log command to display the log of all flow events on the current SmartEdge router.

Note:  
By default, most show commands (in any mode) display information for the current context only or, depending on the command syntax, for all contexts. If you are an administrator for the local context, you can insert the optional context ctx-name construct, preceding the show command, to view output for the specified context without entering that context. For more information about using the context ctx-name construct, see the context command description.

Note:  
By appending a space followed by the pipe ( | ) character at the end of a show command, you can filter the output using a set of modifier keywords and arguments. For more information, see “Modifying Output of show Commands” in Using the CLI.

1.41.5   Examples

The following example shows how to display the log of flow events on the current SmartEdge router:

[local]Redback(config)#show flow log



Time		Evnt	SubEvent		Circuit		Details

----			----------------------------------------------

264.99		Proc	Create-thread				cmd

264.31		Proc	Create-thread				ppa-rx

264.33		Proc	Create-thread				ism-rx

264.33		Proc	Endpoint-alive				ism-mbe

264.34		ISM	FSM-Event				MBE-EP-Up

264.34		ISM	FSM-New-State				MBE-EP-up (All-EP-down)

1.42   show flow ppa log circuit

show flow ppa log circuit circuit_name {continuous | duration duration}

1.42.1   Purpose

Displays statistics associated with the pull value of the current PPA log for a specified circuit.

1.42.2   Command Mode

1.42.3   Syntax Description

circuit_name

Name of the circuit for which you are displaying ppa log information.

continuous

Specifies the amount of time for which ppa log information is being displayed is ongoing.

duration duration

Time interval in seconds for which ppa log information is being displayed

1.42.4   Default

None

1.42.5   Usage Guidelines

Use the show flow ppa log circuit to display statistics associated with the pull value of the current PPA log for a specified circuit.

1.42.6   Examples

The following example shows how to display statistics associated with the pull value of the current PPA log for the circuit1 circuit:

[local]Redback(config-ctx)#show flow ppa log 1/1:1023:63/1/2/6 circuit1

1.43   show flow ppa state

show flow ppa state

1.43.1   Purpose

Displays Packet Processing ASIC (PPA) communications state information for all flows on the current SmartEdge router.

1.43.2   Command Mode

1.43.3   Syntax Description

This command has no keywords or arguments.

1.43.4   Default

None

1.43.5   Usage Guidelines

Use the show flow ppa state command to display PPA communications state information for all flows on the current SmartEdge router.

Note:  
By default, most show commands (in any mode) display information for the current context only or, depending on the command syntax, for all contexts. If you are an administrator for the local context, you can insert the optional context ctx-name construct, preceding the show command, to view output for the specified context without entering that context. For more information about using the context ctx-name construct, see the context command description.

Note:  
By appending a space followed by the pipe ( | ) character at the end of a show command, you can filter the output using a set of modifier keywords and arguments. For more information, see “Modifying Output of show Commands” in Using the CLI.

1.43.6   Examples

The following example shows how to display PPA communication state information for the current circuit:

[local]Redback(config)#show flow ppa state

S:P	EP Name		Index		PR	ES	EU	SE

--------------------------------------------------------

1:I FLOW SLOT 01/0			0000005		Y	Y	Y	Y

1:E FLOW	SLOT	01/1	0000004		Y	Y	Y	Y

1.44   show flow ppa summary

show flow ppa circuit circuit summary

1.44.1   Purpose

Displays a summary of flow counters for a specified circuit.

1.44.2   Command Mode

1.44.3   Syntax Description

circuit circuit

Circuit to which the FAC profile is applied.

1.44.4   Default

None

1.44.5   Usage Guidelines

Use the show flow ppa circuit summary to display a summary of flow counters for a specified circuit.

1.44.6   Examples

The following example shows how to display a summary of flow counters for the circuit1 circuit:

[local]Redback(config-ctx)#show flow ppa circuit 1/1:1023:63/1/2/6 summary

1.45   show forward policy

show forward policy pol-name

1.45.1   Purpose

Displays information about configured forward policies.

1.45.2   Command Mode

all modes

1.45.3   Syntax Description

pol-name

Forward policy name.

1.45.4   Default

None

1.45.5   Usage Guidelines

Use the show forward policy command to display information about configured forward policies.

Note:  
By default, most show commands (in any mode) display information for the current context only or, depending on the command syntax, for all contexts. If you are an administrator for the local context, you can insert the optional context ctx-name construct, preceding the show command, to view output for the specified context without entering that context. For more information about using the context ctx-name construct, see the context command description.

Note:  
By appending a space followed by the pipe ( | ) character at the end of a show command, you can filter the output using a set of modifier keywords and arguments. For more information, see “Modifying Output of show Commands” in Using the CLI.

Note:  
Configurations with mirror actions include an IP-Addr/Option column in SmartEdge router , Release 6.1.4.2 and higher to show the l2-frames option.

1.45.6   Examples

The following example displays brief information about the redirect_policy forward policy:

[local]Redback>show forward policy redirect_policy
Policy-Name          Type     Grid    Qs Slots  Ports  Bound  DnLd  Status

redirect_policy      forward  3       0  2      42     in/out



Total policy map: 1

The following example displays detailed information for the multi_policy forward policy:

[local]Redback>show forward policy multi_policy
Policy-Name          Type     Grid    Qs Slots  Ports  Bound  DnLd  Status

multi_policy         forward  1       0  1      1      in



Slot#:       1   2   3   4   5   6   7   8   9  10  11  12  13  14

iPPA dnld:

ePPA dnld:

iPPA ports:          1

ePPA ports:



Class-Name          Action  Mode  IP-Address       Bound  Int,msec   Output-Name

redir1              redir   hop   10.3.50.2

                                   default

redir2              redir   local



Total policy map: 1

The following example displays detailed information about the l2_policy forward policy configured with the mirror destination dest-name l2-frames command for mirroring Layer 2 attachment circuits:

[local]Redback>show forward policy l2_policy
Policy-Name          Type     Grid    Qs Slots  Ports  Bound  DnLd  Status

l2_policy            forward  1       0  0      0                   updt 


Slot#:       1   2   3   4   5   6   7   8   9  10  11  12  13  14

iPPA dnld:

ePPA dnld:

iPPA ports:          

ePPA ports:


Class-Name          Action  Mode  IP-Addr/Option   Bound  Int,msec  Output-Name

default             mirror  forw  l2-frames        no     20000     you_bar Total policy map: 1 [local]Redback#  

                                   

1.46   show frame-relay

For ports on channelized OC-12 or STM-1 traffic cards, the syntax is:

show frame-relay [slot/port[:chan-num[:sub-chan-num]] [dlci dlci]] [detail]

For channelized ports on DS-3 or E1 traffic cards, the syntax is:

show frame-relay [slot/port[:chan-num] [dlci dlci]] [detail]

For clear-channel ports on DS-3, E3, or E1 traffic cards, or ports on Packet over SONET/SDH (POS) traffic cards, the syntax is:

show frame-relay [slot/port [dlci dlci]] [detail]

1.46.1   Purpose

Displays configuration information for configured Frame Relay permanent virtual circuits (PVCs).

1.46.2   Command Mode

all modes

1.46.3   Syntax Description

slot

Optional. Chassis slot number of a traffic card for which circuit information is displayed. If omitted, displays circuit information for all circuits in the system.

port

Required if you enter the slot argument. Port number for which circuit information is displayed.

chan-num

Optional. Channel number for which circuit information is displayed. If omitted, displays circuit information for all channels on the specified port. The range of values depends on the type of port; see Table 24 for the range of values.

sub-chan-num

Optional. Subchannel number for which circuit information is displayed. If omitted, displays circuit information for all subchannels in the specified channel. The range of values depends on the type of port; see Table 24 for the range of values.

dlci dlci

Optional. Data-link connection identifier (DLCI) of the configured PVC. The range of values is 16 to 991.

detail

Optional. Displays detailed circuit information.

1.46.4   Default

Displays configuration information for all configured Frame Relay PVCs.

1.46.5   Usage Guidelines

Use the show frame-relay command to display configuration information for configured Frame Relay PVCs.

Note:  
The SmartEdge 100 router does not support Frame Relay PVCs.

Table 24 lists the range of values for the chan-num and sub-chan-num arguments for various types of channelized ports.

Table 24    Range of Values for the chan-num and sub-chan-num Arguments

Port

Channel Types

chan-num Range

sub-chan-num Range

Channelized OC-12

DS-3, DS-1

1 to 12

1 to 28

Channelized STM-1

E1, DS-0 channel group

1 to 63

1 to 31

Channelized DS-3

DS-1

1 to 28

Channelized E1

DS-0 channel group

1 to 31

If you enter the optional slot, port, and chan-num arguments, the command displays configuration information for the specified card, port, or channel; if you enter the optional sub-chan-num argument, the command displays configuration information for the DS-1 channel or DS-0 channel group.

If you enter the optional dlci dlci construct, the output displays configuration information for the specified circuit.

Note:  
By default, most show commands (in any mode) display information for the current context only or, depending on the command syntax, for all contexts. If you are an administrator for the local context, you can insert the optional context ctx-name construct, preceding the show command, to view output for the specified context without entering that context. For more information about using the context ctx-name construct, see the context command description.

Note:  
By appending a space followed by the pipe ( | ) character at the end of a show command, you can filter the output using a set of modifier keywords and arguments. For more information, see “Modifying Output of show Commands” in Using the CLI.

1.46.6   Examples

The following example shows how to display detailed configuration information for all Frame Relay PVCs:

[local]Redback>show frame-relay detail
Circuit: 1/1:1:1, internal id: 3/1/6, state: Up

----------------------------------------------------------

bound to          : 

admin state       : Down              hardware address  : 00:00:00:00:00:00 

media type        : sonet             encap type        : frame-relay       

mode type         : 0x2               port type         : ds1               

mtu size          : 1500              cct speed         : 0                 

if_flags          : 0x0               version           : 14366             

internal handle   : 1/1:1:1/3/1/6

Circuit: 1/1:1:1, internal id: 6/2/7, state: Up

----------------------------------------------------------

bound to          : 

admin state       : Down              hardware address  : 00:00:00:00:00:00 

media type        : sonet             encap type        : frame-relay       

mode type         : 0x2               port type         : ds1               

mtu size          : 1500              cct speed         : 1536              

if_flags          : 0x0               version           : 15139             

internal handle   : 1/1:1:1/6/2/7



Circuit: 1/1:1:1 dlci 1023, internal id: 6/2/8, state: Up

----------------------------------------------------------

bound to          : 

admin state       : Down              hardware address  : 00:00:00:00:00:00 

media type        : sonet             encap type        : frame-relay       

mode type         : 0x2               port type         : ds1               

mtu size          : 1500              cct speed         : 1536              

if_flags          : 0x0               version           : 15140             

internal handle   : 1/1:1:1/6/2/8



Circuit: 1/1:1:1 dlci 20, internal id: 6/2/9, state: Up

----------------------------------------------------------

bound to          : 1.1.dlci20@local

admin state       : Down              hardware address  : 00:00:00:00:00:00 

media type        : sonet             encap type        : frame-relay       

mode type         : 0x2               port type         : ds1               

mtu size          : 1500              cct speed         : 1536              

version           : 15141             

internal handle   : 1/1:1:1/6/2/9

.

.

1.47   show frame-relay counters

For ports on channelized OC-12 or STM-1 traffic cards, the syntax is:

show frame-relay counters [persistent] [slot/port[:chan-num[:sub-chan-num]] [dlci dlci ]] [detail]

For channelized ports on DS-3 or E1 traffic cards, the syntax is:

show frame-relay counters [persistent] [slot/port[:chan-num] [dlci dlci ]] [detail]

For clear-channel ports on DS-3, E3, or E1 traffic cards or ports on Packet over SONET/SDH (POS) traffic cards, the syntax is:

show frame-relay counters [persistent] [slot/port [dlci dlci ]] [detail]

1.47.1   Purpose

Displays traffic counters for configured Frame Relay permanent virtual circuits (PVCs).

1.47.2   Command Mode

all modes

1.47.3   Syntax Description

persistent

Optional. If omitted, displays values since the counters were last cleared or the card was last reloaded. If specified, displays values since the system was last reloaded.

slot

Optional. Chassis slot number of a traffic card with the port for which traffic counters are displayed.

port

Required if you enter the slot argument. Port number for the port for which traffic counters are displayed.

chan-num

Optional. Channel for which traffic counters are displayed. The range of values depends on the type of port; see Table 25 for the range of values.

sub-chan-num

Optional. Subchannel number for which the traffic counters are displayed. If not specified, displays traffic counters for all subchannels in the specified channel. The range of values depends on the type of port; see Table 25 for the range of values.

dlci dlci

Optional. Data-link connection identifier (DLCI) of a configured Frame Relay PVC for which to display traffic counters. The range of values is 16 to 991.

detail

Optional. Specifies that more details are displayed for each Frame Relay PVC.

1.47.4   Default

Displays the traffic counters for all Frame Relay PVCs that are bound in the current context.

1.47.5   Usage Guidelines

Note:  
The SmartEdge 100 router does not support Frame Relay PVCs.

Table 25 lists the range of values for the chan-num and sub-chan-num arguments for various types of channelized ports.

Table 25    Range of Values for the chan-num and sub-chan-num Arguments

Port

Channel Types

chan-num Range

sub-chan-num Range

Channelized OC-12

DS-3, DS-1

1 to 12

1 to 28

Channelized STM-1

E1, DS-0 channel group

1 to 63

1 to 31

Channelized DS-3

DS-1

1 to 28

Channelized E1

DS-0 channel group

1 to 31

To display the counters with values accumulated since the system was last reloaded, issue the show frame-relay counters command with the persistent keyword.

The show frame-relay counters command is an alias for the show circuit counters fr command in exec mode.

Use the slot and port arguments to display only Frame Relay PVCs configured on the card in that slot or on that port; if not specified, Frame Relay traffic counters are displayed for all ports in all slots in the system.

If the port is on a channelized OC-12 traffic card, use the chan-num argument to display the traffic counters for only that DS-3 channel; use the sub-chan-num argument to display the traffic counters for only that DS-1 channel or DS-0 channel group. Otherwise, the traffic counters for all Frame Relay PVCs on that slot and port are displayed.

Use the dlci dlci construct to display traffic counters for only a single Frame Relay PVC.

Use the detail keyword to display detailed output for each specified slot, port, channel, or Frame Relay PVC; otherwise, the output displays one line of output for each specified slot, port, channel, or Frame Relay PVC.

Note:  
By default, most show commands (in any mode) display information for the current context only or, depending on the command syntax, for all contexts. If you are an administrator for the local context, you can insert the optional context ctx-name construct, preceding the show command, to view output for the specified context without entering that context. For more information about using the context ctx-name construct, see the context command description.

Note:  
By appending a space followed by the pipe ( | ) character at the end of a show command, you can filter the output using a set of modifier keywords and arguments. For more information, see “Modifying Output of show Commands” in Using the CLI.

1.47.6   Examples

The following example shows how to display the traffic counters for the Frame Relay-encapsulated PVCs on POS port 2 in slot 6:

[local]Redback>show frame-relay counters 6/2
Circuit                      Packets/Bytes Sent  Packets/Bytes Received

6/2                                           0                       0

                                              0                       0

6/2                                           0                       0

                                              0                       0

6/2 dlci 1023                                 0                       0

                                              0                       0

6/2 dlci 16                                   0                       0

                                              0                       0

1.48   show frame-relay lmi-config

For ports on channelized OC-12 or STM-1 traffic cards, the syntax is:

show frame-relay lmi-config [slot[/port[:chan-num[:sub-chan-num]]]]

For channelized ports on DS-3 or E1 traffic cards, the syntax is:

show frame-relay lmi-config [slot[/port[:chan-num]]]

For clear-channel ports on DS-3, E3, or E1 traffic cards, or ports on Packet over SONET/SDH (POS) traffic cards, the syntax is:

show frame-relay lmi-config [slot[/port]]

1.48.1   Purpose

Displays Frame Relay Local Management Interface (LMI) configuration information.

1.48.2   Command Mode

all modes

1.48.3   Syntax Description

slot

Optional. Chassis slot number of a traffic card with the port for which the LMI configuration displays. If not specified, LMI configuration data displays for all Frame Relay-encapsulated ports in all slots.

port

Optional. Port number of the port for which the LMI configuration displays. If not specified, LMI configuration data displays for all Frame Relay-encapsulated ports on the card in the specified slot.

chan-num

Optional. Channel for which the LMI configuration displays. If not specified, displays LMI configuration data for all channels on the specified port. The range of values depends on the type of port; see Table 26 for the range of values.

sub-chan-num

Optional. Subchannel number for which LMI configuration data displays. If not specified, displays LMI configuration data for all subchannels in the specified channel. The range of values depends on the type of port; see Table 26 for the range of values.

1.48.4   Default

Displays the LMI configuration information for all configured Frame Relay-encapsulated ports or channels in all slots.

1.48.5   Usage Guidelines

Use the show frame-relay lmi-config command to display LMI configuration information.

Note:  
The SmartEdge 100 router does not support Frame Relay PVCs.

Table 26 lists the range of values for the chan-num and sub-chan-num arguments for various types of channelized ports.

Table 26    Range of Values for the chan-num and sub-chan-num Arguments

Port

Channel Types

chan-num Range

sub-chan-num Range

Channelized OC-12

DS-3, DS-1

1 to 12

1 to 28

Channelized STM-1

E1, DS-0 channel group

1 to 63

1 to 31

Channelized DS-3

DS-1

1 to 28

Channelized E1

DS-0 channel group

1 to 31

If you specify the slot and port arguments, the display shows the configuration for just that port; if you specify the chan-num argument, the display shows the configuration for just that channel; if you specify the sub-chan-num argument, the display shows the configuration for just that subchannel.

Note:  
By default, most show commands (in any mode) display information for the current context only or, depending on the command syntax, for all contexts. If you are an administrator for the local context, you can insert the optional context ctx-name construct, preceding the show command, to view output for the specified context without entering that context. For more information about using the context ctx-name construct, see the context command description.

Note:  
By appending a space followed by the pipe ( | ) character at the end of a show command, you can filter the output using a set of modifier keywords and arguments. For more information, see “Modifying Output of show Commands” in Using the CLI.

1.48.6   Examples

The following example shows how to display the configuration for DS-3 channel 1 on channelized OC-12 port 1 in slot 3:

[local]Redback>show frame-relay lmi-config 3/1:1
                                  Keep  --------DCE-------- -- DTE --

Slot/Port    Dlci Link Type State Alive T392 N391 N392 N393 N392 N393

------------ ---- ---- ---- ----- ----- ---- ---- ---- ---- ---- ----

       3/1:1 1023  dte   g4    up    10   15    6    3    4    3    4

1.49   show frame-relay lmi-errors

For ports on channelized OC-12 or STM-1 traffic cards, the syntax is:

show frame-relay lmi-errors [bootup] [full] [slot[/port[:chan-num[:sub-chan-num]]]]

For channelized ports on DS-3 or E1 traffic cards, the syntax is:

show frame-relay lmi-errors [bootup] [full] [slot[/port[:chan-num]]]

For clear-channel ports on DS-3, E3, and E1 traffic cards, or ports on Packet over SONET/SDH (POS) traffic cards, the syntax is:

show frame-relay lmi-errors [bootup] [full] [slot[/port]]

1.49.1   Purpose

Displays Frame Relay Local Management Interface (LMI) error counters.

1.49.2   Command Mode

all modes

1.49.3   Syntax Description

bootup

Optional. Displays LMI error counters accumulated since the time the system was last reloaded. If not specified, the LMI error counters are accumulated since the last time the show frame-relay lmi-errors command was issued.

full

Optional. Displays LMI error counters for all LMIs.

slot

Optional. chassis slot number of a traffic card for which LMI error counters are displayed. If not specified, displays LMI error counters for all Frame Relay ports in all slots.

port

Optional. Port number for which LMI error counters are displayed. If not specified, displays LMI error counters for all Frame Relay ports in the specified slot.

chan-num

Optional. Channel number for which LMI error counters are displayed. If not specified, displays LMI error counters for all channels on the specified port. The range of values depends on the type of port; see Table 27 for the range of values.

sub-chan-num

Optional. Subchannel number for which LMI error counters are displayed. If not specified, displays LMI error counters for all subchannels in the specified channel. The range of values depends on the type of port; see Table 27 for the range of values.

1.49.4   Default

Displays LMI error counters for all configured Frame Relay encapsulated channels or ports in all slots since the last time the system was reloaded (booted).

1.49.5   Usage Guidelines

Use the show frame-relay lmi-errors to display LMI error counters.

Note:  
The SmartEdge 100 router does not support Frame Relay PVCs.

Table 27 lists the range of values for the chan-num and sub-chan-num arguments for various types of channelized ports.

Table 27    Range of Values for the chan-num and sub-chan-num Arguments

Port

Channel Types

chan-num Range

sub-chan-num Range

Channelized OC-12

DS-3, DS-1

1 to 12

1 to 28

Channelized STM-1

E1, DS-0 channel group

1 to 63

1 to 31

Channelized DS-3

DS-1

1 to 28

Channelized E1

DS-0 channel group

1 to 31

If you specify the slot and port arguments, only the LMI error counters for that slot or port are displayed; if you specify the chan-num argument, the display shows the LMI error counters for just that channel; if you specify the sub-chan-num argument, the display shows the LMI error counters for just that subchannel.

The system maintains the following sets of error counters for each LMI interface: general errors that apply regardless of the LMI interface type, error counters that only apply to the DCE interface, and error counters that only apply to the data terminal equipment (DTE) interface.

Note:  
By default, most show commands (in any mode) display information for the current context only or, depending on the command syntax, for all contexts. If you are an administrator for the local context, you can insert the optional context ctx-name construct, preceding the show command, to view output for the specified context without entering that context. For more information about using the context ctx-name construct, see the context command description.

Note:  
By appending a space followed by the pipe ( | ) character at the end of a show command, you can filter the output using a set of modifier keywords and arguments. For more information, see “Modifying Output of show Commands” in Using the CLI.

When the error counters are displayed, the general errors are always shown. Then normally the error counters for only the configured LMI interface type are displayed. For example, if port is configured with a Frame Relay interface type of DTE, only the DTE error counters are displayed. Both the DTE and DCE error counters are displayed if you specify the full keyword.

1.49.6   Examples

The following example shows how to display the LMI error counters for DS-3 channel 11 on channelized OC-12 port 1 that is configured as a DTE interface:

[local]Redback>show frame-relay lmi-errors 3/1:11
3/1:11 General errors since Wed Aug 29 21:47:03 2002

Last cleared: never

Header errors:         0

Unknown Messages:      0        Invalid Unnumbered frame:   0

Frame too big:         0        Status rcvd for unkn pvc:   0

Too Many Status Enq:   0        Unexpected PVC Stat IE:     0

Too Few Stat Enq:      0        No response to Stat Enq:    3



3/1:11 DTE LMI errors

Q.922 Header errors:   0        Protocol errors:            0

Unknown Messages:      0        Info Element missing:       0

KeepAlive IE Missing:  0        KeepAlive Seq errors:       0

Unknown IE errors:     0        Positive Threshold Events:  0

Total Negative Events: 0        Current Threshold state:    Normal

1.50   show frame-relay lmi-stats

For ports on channelized OC-12 or STM-1 traffic cards, the syntax is:

show frame-relay lmi-stats [bootup] [slot[/port[:chan-num[:sub-chan-num]]]]

For channelized ports on DS-3 or E1 traffic cards, the syntax is:

show frame-relay lmi-stats [bootup] [slot[/port[:chan-num]]]

For clear-channel ports on DS-3, E3, or E1 traffic cards, or ports on Packet over SONET/SDH (POS) traffic cards, the syntax is:

show frame-relay lmi-stats [bootup] [slot[/port]]

1.50.1   Purpose

Displays Frame Relay Local Management Interface (LMI) statistics counters.

1.50.2   Command Mode

all modes

1.50.3   Syntax Description

bootup

Optional. Displays LMI statistics counters accumulated since the time the system was last reloaded. If not specified, the LMI statistics counters are accumulated since the last time the show frame-relay lmi-stats command was issued.

slot

Optional. Chassis slot number of a traffic card for which LMI statistics counters are displayed. If not specified, displays LMI statistics counters for all configured Frame Relay encapsulated ports in all slots.

port

Optional. Port number of the port for which LMI statistics counters are displayed. If not specified, displays LMI statistics counters for all Frame Relay encapsulated ports in the specified slot.

chan-num

Optional. Channel number for which LMI statistics counters are displayed. If not specified, displays LMI statistics counters for all channels on the specified port. The range of values depends on the type of port; see Table 28 for the range of values.

sub-chan-num

Optional. Subchannel number for which LMI statistics counters are displayed. If not specified, displays LMI statistics counters for all subchannels in the specified channel. The range of values depends on the type of port; see Table 28 for the range of values.

1.50.4   Default

Displays LMI statistics counters for all configured Frame Relay channels on all ports in all slots since the last time the system was reloaded (booted).

1.50.5   Usage Guidelines

Use the show frame-relay lmi-stats command to display LMI statistics counters.

Note:  
The SmartEdge 100 router does not support Frame Relay PVCs.

Table 28 lists the range of values for the chan-num and sub-chan-num arguments for various types of channelized ports.

Table 28    Range of Values for the chan-num and sub-chan-num Arguments

Port

Channel Types

chan-num Range

sub-chan-num Range

Channelized OC-12

DS-3, DS-1

1 to 12

1 to 28

Channelized STM-1

E1, DS-0 channel group

1 to 63

1 to 31

Channelized DS-3

DS-1

1 to 28

Channelized E1

DS-0 channel group

1 to 31

If you specify the slot and port arguments, the LMI statistics for that slot or port are displayed; if you specify the chan-num argument, the display shows the statistics for just that channel; if you specify the sub-chan-num argument, the display shows the statistics for just that subchannel.

Note:  
By default, most show commands (in any mode) display information for the current context only or, depending on the command syntax, for all contexts. If you are an administrator for the local context, you can insert the optional context ctx-name construct, preceding the show command, to view output for the specified context without entering that context. For more information about using the context ctx-name construct, see the context command description.

Note:  
By appending a space followed by the pipe ( | ) character at the end of a show command, you can filter the output using a set of modifier keywords and arguments. For more information, see “Modifying Output of show Commands” in Using the CLI.

1.50.6   Examples

The following example shows how to display LMI statistics counters for DS-3 channel 11 on channelized OC-12 port 1:

[local]Redback>show frame-relay lmi-stats 3/1:11
3/1:11 LMI stats since Wed Aug 29 21:45:18 2002

Last cleared: never

status enquires sent:      563  status enquires rcvd:        0

full status enqs sent:      94  full status enqs rcvd:       0

status messages sent:        0  status messages rcvd:      560

full status msgs sent:       0  full status msgs rcvd:      94

                                async updates rcvd:          0

1.51   show frame-relay profile

show frame-relay profile [prof-name]

1.51.1   Purpose

Displays information about Frame Relay profiles configured in the current context.

1.51.2   Command Mode

all modes

1.51.3   Syntax Description

prof-name

Optional. Name of the configured Frame Relay profile.

1.51.4   Default

When used without the optional argument, displays a brief description of all configured Frame Relay profiles.

1.51.5   Usage Guidelines

Use the show frame-relay profile command to display information about Frame Relay profiles configured in the current context.

Note:  
The SmartEdge 100 router does not support Frame Relay PVCs.

Note:  
By default, most show commands (in any mode) display information for the current context only or, depending on the command syntax, for all contexts. If you are an administrator for the local context, you can insert the optional context ctx-name construct, preceding the show command, to view output for the specified context without entering that context. For more information about using the context ctx-name construct, see the context command description.

Note:  
By appending a space followed by the pipe ( | ) character at the end of a show command, you can filter the output using a set of modifier keywords and arguments. For more information, see “Modifying Output of show Commands” in Using the CLI.

1.51.6   Examples

The following example shows how to display information about all Frame Relay profiles configured in the local context:

[local]Redback>show frame-relay profile
Name               Counters        PVCs

------------------ --------------- ----

fr-pro             none            1



Total: 1

1.52   show frame-relay pvc

For ports on channelized OC-12 or STM-1 traffic cards, the syntax is:

show frame-relay pvc [all | active | inactive | l2vpn | summary] [slot[/port[:chan-num[:sub-chan-num]] [dlci dlci]]]

For channelized ports on DS-3 or E1 traffic cards, the syntax is:

show frame-relay pvc [all | active | inactive | l2vpn | summary] [slot[/port[:chan-num] [dlci dlci]]]

For clear-channel ports on DS-3, E3, or E1 traffic cards, or ports on Packet over SONET/SDH (POS) traffic cards, the syntax is:

show frame-relay pvc [all | active | inactive | l2vpn | summary] [slot[/port [dlci dlci]]

1.52.1   Purpose

Displays a list of configured Frame Relay permanent virtual circuits (PVCs).

1.52.2   Command Mode

all modes

1.52.3   Syntax Description

all

Optional. Displays information for all configured Frame Relay PVCs in all contexts. This option is valid only in the local context.

active

Optional. Displays only active Frame Relay PVCs.

inactive

Optional. Displays only Frame Relay PVCs in the Down state.

l2vpn

Optional. Displays only Frame Relay PVCs that are enabled for Layer 2 Virtual Private Networks (L2VPNs).

summary

Optional. Displays only a summary of bound and unbound Frame Relay PVCs.

slot

Optional. Chassis slot number of a traffic card with the port for which Frame Relay PVCs are displayed. If not specified, displays PVCs that are bound in the current context for all configured Frame Relay PVCs in all slots.

port

Optional. Port number of the port for which PVCs are displayed. If not specified, displays Frame Relay PVCs for all ports in the specified slot.

chan-num

Optional. Channel number for which Frame Relay PVCs are displayed. If not specified, displays Frame Relay PVCs for all channels on the specified port. The range of values depends on the type of port; see Table 29 for the range of values.

sub-chan-num

Optional. Subchannel number for which the Frame Relay PVCs are displayed. If not specified, displays Frame Relay PVCs for all subchannels in the specified channel. The range of values depends on the type of port; see Table 29 for the range of values.

dlci dlci

Optional. Data-link connection identifier (DLCI) of the configured Frame Relay PVC. The range of values is 16 to 991. If not specified, displays Frame Relay PVCs for all DLCIs as specified by the slot, port, chan-num, and sub-chan-num arguments.

1.52.4   Default

Displays all configured Frame Relay PVCs that are bound in the current context.

1.52.5   Usage Guidelines

Use the show frame-relay pvc command to display a list of configured Frame Relay PVCs.

Note:  
The SmartEdge 100 router does not support Frame Relay PVCs.

Table 29 lists the range of values for the chan-num and sub-chan-num arguments for various types of channelized ports.

Table 29    Range of Values for the chan-num and sub-chan-num Arguments

Port

Channel Types

chan-num Range

sub-chan-num Range

Channelized OC-12

DS-3, DS-1

1 to 12

1 to 28

Channelized STM-1

E1, DS-0 channel group

1 to 63

1 to 31

Channelized DS-3

DS-1

1 to 28

Channelized E1

DS-0 channel group

1 to 31

In the local context, use the all keyword to display information about all configured Frame Relay PVCs, both bound (in any context) and unbound. This keyword is valid only in the local context. For any other context, only the Frame Relay PVCs that are bound within the current context are displayed.

Use the active keyword to display only the active Frame Relay PVCs; use the inactive keyword to display only the inactive PVCs.

Use the l2vpn keyword to display all Frame Relay PVCs that are enabled for L2VPN. Output for the option displays three states for each PVC:

Use the summary keyword to display only summary information.

Use the slot and port arguments to display only PVCs for that slot or that port. If the port is on a channelized OC-12 traffic card or STM-1 traffic card, use the chan-num argument to display only the PVCs on that channel; use the sub-chan-num argument to display only the PVCs on that DS-1 channel or DS-0 channel group; otherwise, the PVCs on all channels on the port are displayed.

Use the dlci dlci construct to display only the Frame Relay PVC with that DLCI.

Note:  
By default, most show commands (in any mode) display information for the current context only or, depending on the command syntax, for all contexts. If you are an administrator for the local context, you can insert the optional context ctx-name construct, preceding the show command, to view output for the specified context without entering that context. For more information about using the context ctx-name construct, see the context command description.

Note:  
By appending a space followed by the pipe ( | ) character at the end of a show command, you can filter the output using a set of modifier keywords and arguments. For more information, see “Modifying Output of show Commands” in Using the CLI.

1.52.6   Examples

The following example shows how to display output for all active Frame Relay PVCs:

[local]Redback>show frame-relay pvc active
Slot/Port      Traffic Profile      State      Encaps    Binding
3/1:1  dlci  16  fr-pro                up    auto1490    1.dlci16@local
3/1:1  dlci  17  fr-pro                up    auto1490    1.dlci17@local
3/1:1  dlci  18  fr-pro                up    auto1490    1.dlci18@local
3/1:1  dlci  19  fr-pro                up    auto1490    1.dlci19@local
3/1:1  dlci  20  fr-pro                up    auto1490    1.dlci20@local
3/1:1  dlci  21  fr-pro                up    auto1490    1.dlci21@local
3/1:1  dlci  22  fr-pro                up    auto1490    1.dlci22@local
3/1:1  dlci  23  fr-pro                up    auto1490    1.dlci23@local
....

Total: 1212 Up: 1212 Down: 0 Shut: 0 Bound: 1212
last status change: Thu Sep 26 01:51:26 2002

The following example shows how to display output for L2VPN-enabled PVCs:

[local]Redback>show frame-relay pvc l2vpn
Circuit                   Local State L2VPN state State
12/1 dlci 100             up          down        down 
12/1 dlci 101             up          down        down 
12/1 dlci 102             up          down        down 
12/1 dlci 103             up          down        down 
12/1 dlci 104             up          down        down 
12/1 dlci 105             up          down        down 
12/1 dlci 106             up          down        down 
12/1 dlci 107             up          down        down 
12/1 dlci 108             up          down        down 
12/1 dlci 109             up          down        down 
12/1 dlci 110             up          down        down 
12/1 dlci 111             up          down        down 
12/1 dlci 112             up          down        down 
12/1 dlci 113             up          down        down 
12/1 dlci 114             up          down        down 
12/1 dlci 115             up          down        down 

The following example shows how to display summary information:

[local]Redback>show frame-relay pvc summary
PVCs total: 1212 Up: 1212 Down: 0 Shut: 0 Bound : 1212
last status change: Thu Sep 26 01:51:26 2002

The following example shows how to display information for the Frame Relay PVC associated with slot 1 port 1, channel 1, DLCI 16 on a channelized OC-12 traffic card:

[local]Redback>show frame-relay pvc 1/1:1 DLCI 16
Slot/Port/Channel: 1/1:1 DLCI:  16
status: up bound to 1.dlci16@local