COMMAND DESCRIPTION     23/190 82-CRA 119 1170/1-V1 Uen A    

Commands: show p through show q

© Copyright Ericsson AB 2009. All rights reserved.

Disclaimer

No part of this document may be reproduced in any form without the written permission of the copyright owner. The contents of this document are subject to revision without notice due to continued progress in methodology, design and manufacturing. Ericsson shall have no liability for any error or damage of any kind resulting from the use of this document.

Trademark List

SmartEdge is a registered trademark of Telefonaktiebolaget L M Ericsson.
NetOp is a trademark of Telefonaktiebolaget L M Ericsson.

Contents

1Command Descriptions
1.1show pim bsr-router
1.2show pim circuit
1.3show pim interface
1.4show pim mdt
1.5show pim neighbor
1.6show pim ppa
1.7show pim rpf
1.8show pim rp-hash
1.9show pim rp mapping
1.10show pim ssm
1.11show pim traffic
1.12show policy access-list
1.13show port
1.14show port counters
1.15show port detail
1.16show port perf-monitor
1.17show port transceiver
1.18show ppp
1.19show ppp counters
1.20show ppp multilink
1.21show pppoe
1.22show pppoe counters
1.23show privilege
1.24show process
1.25show process flowd
1.26show process lm
1.27show pseudowire
1.28show public- key
1.29show qos agent-circuit-id
1.30show qos circuit
1.31show qos class-definition
1.32show qos class-map
1.33show qos client
1.34show qos congestion-map
1.35show qos h-node
1.36show qos memory
1.37show qos policy
1.38show qos policy atmwfq
1.39show qos policy edrr
1.40show qos policy metering
1.41show qos policy policing
1.42show qos policy pq
1.43show qos policy pwfq
1.44show qos port
1.45show qos port-map
1.46show qos port-map bind
1.47show qos queue-map
1.48show qos username


1   Command Descriptions

Commands starting with “show p” through commands starting with “show q” are included.

1.1   show pim bsr-router

show pim bsr-router

1.1.1   Purpose

1.1.2   Command Mode

all modes

1.1.3   Syntax Description

This command has no keywords or arguments.

1.1.4   Default

None

1.1.5   Usage Guidelines

Note:  
By default, most show commands (in any mode) display information for the current context only or, depending on the command syntax, for all contexts. If you are an administrator for the local context, you can insert the optional context ctx-name construct, preceding the show command, to view output for the specified context without entering that context. For more information about using the context ctx-name construct, see the context command description.

Note:  
By appending a space followed by the pipe ( | ) character at the end of a show command, you can filter the output using a set of modifier keywords and arguments. For more information, see “Modifying Output of show Commands” in Using the CLI.

1.1.6   Examples

The following example displays information for all BSRs and C-RPs:

[local]Redback>show pim bsr-router
PIM Bootstrap Information

BSR address:    11.1.1.1

Uptime:         3d06h, BSR Priority: 0, Hash mask length: 0

Next Bootstrap: 00:00:37



Next Candidate RP advertisement in 00:00:42

RP: 11.1.1.1(fxp1), Group Acl:

1.2   show pim circuit

show pim circuit

1.2.1   Purpose

1.2.2   Command Mode

all modes

1.2.3   Syntax Description

This command has no keywords or arguments.

1.2.4   Default

None

1.2.5   Usage Guidelines

Note:  
By default, most show commands (in any mode) display information for the current context only or, depending on the command syntax, for all contexts. If you are an administrator for the local context, you can insert the optional context ctx-name construct, preceding the show command, to view output for the specified context without entering that context. For more information about using the context ctx-name construct, see the context command description.

Note:  
By appending a space followed by the pipe ( | ) character at the end of a show command, you can filter the output using a set of modifier keywords and arguments. For more information, see “Modifying Output of show Commands” in Using the CLI.

1.2.6   Examples

The following example displays circuit-specific information for PIM:

[local]Redback>show pim circuit
  Number of circuits: 4

    1/9:1023:63/1/1/5, fxp1, Up, recv permit/send permit/unsol permit

    1/11:1023:63/1/1/13, fxp2, Up, recv permit/send permit/unsol permit

    12/1:1:63/1/2/18, fxp3, Up, recv permit/send permit/unsol permit

    12/1:1:63/1/2/19, fxp3, Up, recv permit/send permit/unsol permit

1.3   show pim interface

show pim interface [if-name]

1.3.1   Purpose

1.3.2   Command Mode

all modes

1.3.3   Syntax Description

if-name

Optional. Name of the PIM interface.

1.3.4   Default

None

1.3.5   Usage Guidelines

Note:  
By default, most show commands (in any mode) display information for the current context only or, depending on the command syntax, for all contexts. If you are an administrator for the local context, you can insert the optional context ctx-name construct, preceding the show command, to view output for the specified context without entering that context. For more information about using the context ctx-name construct, see the context command description.

Note:  
By appending a space followed by the pipe ( | ) character at the end of a show command, you can filter the output using a set of modifier keywords and arguments. For more information, see “Modifying Output of show Commands” in Using the CLI.

1.3.6   Examples

The following example displays information for all PIM-enabled interfaces:

[local]Redback>show pim interface
Address         Interface           Mode    Cct   Up Nbr   Hello DR

                                            Count Dn Count Intvl

101.1.1.1       fxp1                sparse  1     Up 0     30    101.1.1.1

102.1.1.1       fxp2                sparse  1     Up 1     30    102.1.1.2

103.1.1.1       fxp3                sparse  1     Up 1     30    103.1.1.2

11.1.1.1        fxp4                sparse  1     Up 0     30    11.1.1.1

61.1.1.1        fxp6                sparse  1     Up 0     30    61.1.1.1

10.200.1.1      lo1                 sparse  1     Dn 0     30    10.200.1.1

1.4   show pim mdt

show pim mdt

1.4.1   Purpose

1.4.2   Command Mode

all modes

1.4.3   Syntax Description

This command has no keywords or arguments.

1.4.4   Default

None

1.4.5   Usage Guidelines

Use the show pim mdt command to display MDT information.

The output from this command is context-specific.

The output in a Virtual Private Network (VPN) context shows the MDT group, the source for the VPN, and the context ID only for that VPN context. The output in local context lists MDT information for all VPNs.

Note:  
By default, most show commands (in any mode) display information for the current context only or, depending on the command syntax, for all contexts. If you are an administrator for the local context, you can insert the optional context ctx-name construct, preceding the show command, to view output for the specified context without entering that context. For more information about using the context ctx-name construct, see the context command description.

Note:  
By appending a space followed by the pipe ( | ) character at the end of a show command, you can filter the output using a set of modifier keywords and arguments. For more information, see “Modifying Output of show Commands” in Using the CLI.

1.4.6   Examples

The following example displays MDT information for a VPN-enabled context, VPN1:

[VPN1]Redback>show pim mdt

Multicast Domain Tree information

MDT Group       Interface           Source              Context

239.1.1.1       ic-local            lo1                 0x40080002

The following example displays MDT information for all VPNs:

[local]Redback>show pim mdt



Multicast Domain Tree information

MDT Group       Interface           Source              Context

239.1.1.1       ic-vpn1             lo1                 0x40080002

196.1.1.1       ic-vpn2             lo2                 0x40080003

10.10.1.1       ic-vpn3             lo3                 0x40080004

1.5   show pim neighbor

show pim neighbor

1.5.1   Purpose

1.5.2   Command Mode

all modes

1.5.3   Syntax Description

This command has no keywords or arguments.

1.5.4   Default

None

1.5.5   Usage Guidelines

Note:  
By default, most show commands (in any mode) display information for the current context only or, depending on the command syntax, for all contexts. If you are an administrator for the local context, you can insert the optional context ctx-name construct, preceding the show command, to view output for the specified context without entering that context. For more information about using the context ctx-name construct, see the context command description.

Note:  
By appending a space followed by the pipe ( | ) character at the end of a show command, you can filter the output using a set of modifier keywords and arguments. For more information, see “Modifying Output of show Commands” in Using the CLI.

1.5.6   Examples

The following example displays information about all PIM neighbors:

[local]Redback>show pim neighbor
PIM Neighbor Table

Neighbor Address Interface         Uptime   Expire   DR Prio  GenID       DR

10.4.1.2         fxp1              00:04:10 00:01:34 0x1      0x17ac7e7a 

10.5.1.4         fxp2              00:25:22 00:01:22 0x1                  Y

1.6   show pim ppa

show pim ppa

1.6.1   Purpose

1.6.2   Command Mode

all modes

1.6.3   Syntax Description

This command has no keywords or arguments.

1.6.4   Default

None

1.6.5   Usage Guidelines

Note:  
By default, most show commands (in any mode) display information for the current context only or, depending on the command syntax, for all contexts. If you are an administrator for the local context, you can insert the optional context ctx-name construct, preceding the show command, to view output for the specified context without entering that context. For more information about using the context ctx-name construct, see the context command description.

Note:  
By appending a space followed by the pipe ( | ) character at the end of a show command, you can filter the output using a set of modifier keywords and arguments. For more information, see “Modifying Output of show Commands” in Using the CLI.

1.6.6   Examples

The following example displays output from the show pim ppa command:

[local]Redback>show pim ppa
Slot 2  IPCs sent  :1               Circuit enable/disable:8/0

ePPA    IPCs rcvd  :1               IPC failures:0        

        IPC blocked:NO              Num of IPCs blocked:1

        Status     :UP              Restarts: 1

        Up/Dn time :17:05:19        Multicast Interfaces:4    

        Version    :54              Goal Version:54



Slot 2  IPCs sent  :1               Circuit enable/disable:8/0

iPPA    IPCs rcvd  :1               IPC failures:0        

        IPC blocked:NO              Num of IPCs blocked:1

        Status     :UP              Restarts: 1

        Up/Dn time :17:05:19        Multicast Interfaces:4    

        Version    :54              Goal Version:54



Slot 11 IPCs sent  :1               Circuit enable/disable:14/0

ePPA    IPCs rcvd  :1               IPC failures:0        

        IPC blocked:NO              Num of IPCs blocked:1

        Status     :UP              Restarts: 1

        Up/Dn time :17:05:19        Multicast Interfaces:7    

        Version    :54              Goal Version:54

1.7   show pim rpf

show pim rpf {src-addr | src-name}

1.7.1   Purpose

Displays reverse path forwarding (RPF) statistics for a specified multicast source.

1.7.2   Command Mode

all modes

1.7.3   Syntax Description

src-addr

IP address of a multicast source.

src-name

Name of a multicast source.

1.7.4   Default

None

1.7.5   Usage Guidelines

Use the show pim rpf command to display RPF statistics for a specified multicast source.

Note:  
By default, most show commands (in any mode) display information for the current context only or, depending on the command syntax, for all contexts. If you are an administrator for the local context, you can insert the optional context ctx-name construct, preceding the show command, to view output for the specified context without entering that context. For more information about using the context ctx-name construct, see the context command description.

Note:  
By appending a space followed by the pipe ( | ) character at the end of a show command, you can filter the output using a set of modifier keywords and arguments. For more information, see “Modifying Output of show Commands” in Using the CLI.

1.7.6   Examples

The following example displays output from the show pim rpf command:

[local]Redback>show pim rpf 11.1.1.1
RPF information for 11.1.1.1

  RPF interface:    fxp1

  RPF neighbor:     102.1.1.1

  RPF route/mask:   11.1.1.0/255.255.255.0

  RPF type:         mbgp

1.8   show pim rp-hash

show pim rp-hash group-addr

1.8.1   Purpose

1.8.2   Command Mode

all modes

1.8.3   Syntax Description

group-addr

IP address of the IGMP group.

1.8.4   Default

None

1.8.5   Usage Guidelines

Use the show pim rp-hash command to display information about the RP to which the specified group hashes (maps).

Note:  
By default, most show commands (in any mode) display information for the current context only or, depending on the command syntax, for all contexts. If you are an administrator for the local context, you can insert the optional context ctx-name construct, preceding the show command, to view output for the specified context without entering that context. For more information about using the context ctx-name construct, see the context command description.

Note:  
By appending a space followed by the pipe ( | ) character at the end of a show command, you can filter the output using a set of modifier keywords and arguments. For more information, see “Modifying Output of show Commands” in Using the CLI.

1.8.6   Examples

The following example displays information about the RP to which the group, 224.121.121.1, hashes:

[local]Redback>show pim rp-hash 224.121.121.1
  RP 10.6.1.2

    Info source: 10.4.1.2, via Bootstrap

         Uptime: 00:05:00, expires: 00:02:58

1.9   show pim rp mapping

show pim rp mapping [group-addr]

1.9.1   Purpose

1.9.2   Command Mode

all modes

1.9.3   Syntax Description

group-addr

Optional. IP address of the Internet Group Management Protocol (IGMP) group.

1.9.4   Default

None

1.9.5   Usage Guidelines

Note:  
By default, most show commands (in any mode) display information for the current context only or, depending on the command syntax, for all contexts. If you are an administrator for the local context, you can insert the optional context ctx-name construct, preceding the show command, to view output for the specified context without entering that context. For more information about using the context ctx-name construct, see the context command description.

Note:  
By appending a space followed by the pipe ( | ) character at the end of a show command, you can filter the output using a set of modifier keywords and arguments. For more information, see “Modifying Output of show Commands” in Using the CLI.

1.9.6   Examples

The following example displays the group-to-RP mapping cache:

[local]Redback>show pim rp mapping
PIM Group-to-RP Mappings

Group(s) 224.24.0.0/16

  RP 10.6.1.2

    Info source: 10.4.1.2, via Bootstrap

         Uptime: 00:04:41, expires: 00:02:17

Group(s) 224.121.0.0/16

  RP 10.6.1.2

    Info source: 10.4.1.2, via Bootstrap

         Uptime: 00:04:41, expires: 00:02:17

1.10   show pim ssm

show pim ssm

1.10.1   Purpose

Displays the Source-Specific Multicast (SSM) setting in Protocol Independent Multicast (PIM).

1.10.2   Command Mode

all modes

1.10.3   Syntax Description

This command has no keywords or arguments.

1.10.4   Default

None

1.10.5   Usage Guidelines

Use the show pim ssm command to display the SSM setting in PIM.

Note:  
By default, most show commands (in any mode) display information for the current context only or, depending on the command syntax, for all contexts. If you are an administrator for the local context, you can insert the optional context ctx-name construct, preceding the show command, to view output for the specified context without entering that context. For more information about using the context ctx-name construct, see the context command description.

Note:  
By appending a space followed by the pipe ( | ) character at the end of a show command, you can filter the output using a set of modifier keywords and arguments. For more information, see “Modifying Output of show Commands” in Using the CLI.

1.10.6   Examples

The following example displays output from the show pim ssm command:

[local]Redback>show pim ssm
Source Specific Multicast (SSM) setting

SSM address range: default (232.0.0.0/8)

1.11   show pim traffic

show pim traffic

1.11.1   Purpose

Displays Protocol Independent Multicast (PIM) traffic statistics.

1.11.2   Command Mode

all modes

1.11.3   Syntax Description

This command has no keywords or arguments.

1.11.4   Default

None

1.11.5   Usage Guidelines

Use the show pim traffic command to display PIM traffic statistics.

Note:  
By default, most show commands (in any mode) display information for the current context only or, depending on the command syntax, for all contexts. If you are an administrator for the local context, you can insert the optional context ctx-name construct, preceding the show command, to view output for the specified context without entering that context. For more information about using the context ctx-name construct, see the context command description.

Note:  
By appending a space followed by the pipe ( | ) character at the end of a show command, you can filter the output using a set of modifier keywords and arguments. For more information, see “Modifying Output of show Commands” in Using the CLI.

1.11.6   Examples

The following example displays PIM traffic statistics:

[local]Redback>show pim traffic
PIM statistics:

 Sent:

      Total 0, Hello 217, Register 0, Register-Stop 0, Join/Prune 5,

      BSR 21, Assert 0, Graft 0, Graft-ack 0, Candidate-RP-advertisement 0

      PIMv1:  Register 0, Register-Stop 0

 Received:

      Total 0, Hello 66, Register 0, Register-Stop 0, Join/Prune 0,

      BSR 12, Assert 0, Graft 0, Graft-ack 0, Candidate-RP-advertisement 0

      PIMv1:  Register 0, Register-Stop 0, Punts 21

 Error:

      Hello 0, Register 0, Register-Stop 0, Join/Prune 0,

      BSR 0, Assert 0, Graft 0, Graft-ack 0, Candidate-RP-advertisement 0

      PIMv1:  Register 0, Register-Stop 0

      I/O errors 0, Short packets 0, Checksum 0

      Unknown type: 0

 Queue:

      Input queue size 0, Input queue overflows 0

1.12   show policy access-list

show policy access-list [{[summary] [acl-name] | first-match acl-name [protocol] {src-addr [port port]} [dest-addr [port port]}] [dscp dscp-value] [length length] [precedence prec-value] [tos tos-value]

1.12.1   Purpose

Displays the status of configured policy access control lists (ACLs).

1.12.2   Command Mode

all modes

1.12.3   Syntax Description

summary

Optional. Excludes the ACL statements from the display. Optionally, you can follow this keyword with the acl-name argument, naming a particular ACL for which you want summary information displayed.

acl-name

Optional. Name of the ACL for which you want information displayed. To display summary information about a specific list, you must enter the summary keyword first, followed by the acl-name argument.

first-match acl-name

Optional. Name of the ACL for which you want to find the first statement matched by the criteria that follows the first-match acl-name construct.

protocol

Optional. Number indicating a protocol as specified in RFC 1700, Assigned Numbers. The range of values is 0 to 255. In place of the protocol argument, you can use any of the following keywords:

  • ahp—Specifies the Authentication Header Protocol.

  • esp—Specifies encapsulation security payload.

  • gre—Specifies Generic Routing Encapsulation.

  • host—Specifies a host source address.

  • icmp—Specifies the Internet Control Message Protocol.

  • igmp—Specifies the Internet Group Management Protocol.

  • ip—Uses any IP protocol.

  • ipinip—Specifies IP-in-IP tunneling.

  • ospf—Specifies Open Shortest Path First.

  • pcp—Specifies the Payload Compression Protocol.

  • pim—Specifies Protocol Independent Multicast.

  • tcp—Specifies the Transmission Control Protocol.

  • udp—Specifies the User Datagram Protocol.

src-addr

Source address to be included in the criteria for a match. An IP address in the form A.B.C.D.

port port

Optional. TCP or UDP port to be considered a match for either the source or destination IP address. This construct is only available if you specified TCP or UDP as the protocol. The range of values is 1 to 65,535. You can also substitute a keyword for the port argument as listed in Table 1 and Table 2 in the “Usage Guidelines” section for this command.

dest-addr

Optional. Destination address to be included in the criteria for a match. An IP address in the form A.B.C.D.

dscp dscp-value

Optional. Differentiated Services Code Point (DSCP) to be included in the criteria for a match. The range of values is 0 to 63. You can also substitute a keyword for the dscp-value argument as listed in Table 3 in the “Usage Guidelines” section for this command.

length length

Optional. Packet length. The length of the network-layer packet, beginning with the IP header. The range of values is 20 to 65,535.

precedence prec-value

Optional. Precedence value of packets to be included in the criteria for a match. The range of values is 0 to 7, 7 being the highest precedence. In place of the prec-value argument, you can enter any of the following keywords:

  • routine—Specifies routine precedence (value = 0).

  • priority—Specifies priority precedence (value = 1).

  • immediate—Specifies immediate precedence (value = 2).

  • flash—Specifies flash precedence (value = 3).

  • flash-override—Specifies flash override precedence (value = 4).

  • critical—Specifies critical precedence (value = 5).

  • internet—Specifies internetwork control precedence (value = 6).

  • network—Specifies network control precedence (value = 7).

tos tos-value

Optional. Type of service (ToS) to be included in the criteria for a match. The range of values is 0 to 15. In place of the tos-value argument, you can enter any of the following keywords:

  • max-reliability—Maximum reliable ToS (value = 2).

  • max-throughput—Maximum throughput ToS (value = 4).

  • min-delay—Minimum delay ToS (value = 8).

  • min-monetary-cost—Minimum monetary cost ToS (value = 1).

  • normal—Normal ToS (value = 0).

To specify both a precedence and a ToS, you must enter the precedence prec-value construct first, followed by the tos tos-value construct.

1.12.4   Default

When entered without any optional syntax, the show policy access-list command displays information for all policy ACLs in the context, including the statements in each list.

1.12.5   Usage Guidelines

Use the show policy access-list command to display the status of configured policy ACLs.

Use the first-match acl-name construct to display the first statement in the policy ACL that is matched by the criteria that follows the first-match acl-name construct.

Table 1 lists the valid keyword substitutions for the port argument when the argument is used to specify a TCP port.

Table 1    Valid Keyword Substitutions for the port Argument (TCP Port)

Keyword

Definition

Corresponding Port Number

bgp

Border Gateway Protocol

179

chargen

Character generator

19

cmd

Remote commands (rcmd)

514

daytime

Daytime

13

discard

Discard

9

domain

Domain Name System

53

echo

Echo

7

exec

Exec (rsh)

512

finger

Finger

79

ftp

File Transfer Protocol

21

ftp-data

FTP data connections (used infrequently)

20

gopher

Gopher

70

hostname

Network interface card (NIC) hostname server

101

ident

Identification protocol

113

irc

Internet Relay Chat

194

klogin

Kerberos login

543

kshell

Kerberos Shell

544

login

Login (rlogin)

513

lpd

Printer service

515

nntp

Network News Transport Protocol

119

pim-auto-rp

Protocol Independent Multicast Auto-RP

496

pop2

Post Office Protocol Version 2

109

pop3

Post Office Protocol Version 3

110

shell

Remote Command Shell

514

smtp

Simple Mail Transport Protocol

25

ssh

Secure Shell

22

sunrpc

Sun Remote Procedure Call

111

syslog

Syslog

514

tacacs

Terminal Access Controller Access Control System

49

talk

Talk

517

telnet

Telnet

23

time

Time

37

uucp

Unix-to-Unix Copy Program

540

whois

Nickname

43

www

World Wide Web (HTTP)

80

Table 2 lists the valid keyword substitutions for the port argument when the argument is used to specify a UDP port.

Table 2    Valid port Argument Keyword Substitution Values for UDP Ports

Keyword

Definition

Corresponding Port Number

biff

Biff (Mail Notification, Comsat)

512

bootpc

Bootstrap Protocol client

68

bootps

Bootstrap Protocol server

67

discard

Discard

9

dnsix

DNSIX Security Protocol Auditing

195

domain

Domain Name System

53

echo

Echo

7

isakmp

Internet Security Association and Key Management Protocol (ISAKMP)

500

mobile-ip

Mobile IP registration

434

nameserver

IEN116 Name Service (obsolete)

42

netbios-dgm

NetBIOS Datagram Service

138

netbios-ns

NetBIOS Name Service

137

netbios-ss

NetBIOS Session Service

139

ntp

Network Time Protocol

123

pim-auto-rp

Protocol Independent Multicast Auto-RP

496

rip

Router Information Protocol

520

snmp

Simple Network Management Protocol

161

snmptrap

SNMP traps

162

sunrpc

Sun Remote Procedure Call

111

syslog

System logger

514

tacacs

Terminal Access Controller Access Control System

49

talk

Talk

517

tftp

Trivial File Transfer Protocol

69

time

Time

37

who

Who Service (rwho)

513

xdmcp

X Display Manager Control Protocol

177

Table 3 lists the valid keyword substitutions for the dscp-value argument.

Table 3    Valid Keyword Substitutions for the dscp-value Argument

Keyword

Definition

af11

Assured Forwarding—Class 1/Drop Precedence 1

af12

Assured Forwarding—Class 1/Drop Precedence 2

af13

Assured Forwarding—Class 1/Drop Precedence 3

af21

Assured Forwarding—Class 2/Drop Precedence 1

af22

Assured Forwarding—Class 2/Drop Precedence 2

af23

Assured Forwarding—Class 2/Drop Precedence 3

af31

Assured Forwarding—Class 3/Drop Precedence 1

af32

Assured Forwarding—Class 3/Drop Precedence 2

af33

Assured Forwarding—Class 3/Drop Precedence 3

af41

Assured Forwarding—Class 4/Drop Precedence 1

af42

Assured Forwarding—Class 4/Drop Precedence 2

af43

Assured Forwarding—Class 4/Drop Precedence 3

cs0

Class Selector 0

cs1

Class Selector 1

cs2

Class Selector 2

cs3

Class Selector 3

cs4

Class Selector 4

cs5

Class Selector 5

cs6

Class Selector 6

cs7

Class Selector 7

df

Default Forwarding (same as cs0)

ef

Expedited Forwarding

Note:  
By default, most show commands (in any mode) display information for the current context only or, depending on the command syntax, for all contexts. If you are an administrator for the local context, you can insert the optional context ctx-name construct, preceding the show command, to view output for the specified context without entering that context. For more information about using the context ctx-name construct, see the context command description.

Note:  
By appending a space followed by the pipe ( | ) character at the end of a show command, you can filter the output using a set of modifier keywords and arguments. For more information, see “Modifying Output of show Commands” in Using the CLI.

1.12.6   Examples

The following example displays information about the policy ACL, diff-serve:

[local]Redback>show policy access-list diff-serve



policy access-list diff-serve:

  count 4, sequences: 10 - 40 client count: 0

  modified: 00:03:08 (hh:mm:ss) ago

   seq 10 permit tcp any eq telnet class Expedited_Flow

   seq 20 permit ip any dscp eq ef class Expedited_Flow

   seq 30 permit tcp any eq ftp class Bulk_Data

   seq 40 permit udp any eq tftp class Bulk_Data

The following example displays information about the policy ACL, redirect_acl:

[local]Redback>show policy access-list redirect_acl



policy access-list redirect_acl:

  count: 3, sequences: 10 - 30, client count: 1

  modified: 00:21:34 (hh:mm:ss) ago, version: 8

   condition 101 time-range

    periodic weekdays 00:00 to 23:59 class redir2

   seq 10 permit tcp any any eq www class redir0 condition 101

   seq 20 permit tcp any any eq 81 class redir1

   seq 30 permit tcp any any eq 82 class redir2

The following example displays information about the policy ACL, qos1:

[local]Redback>show policy access-list qos1



policy access-list qos1:

  count: 1, sequences: 10 - 10, client count: 1

  modified: 00:08:35 (hh:mm:ss) ago, version: 4

   condition 100 time-range

    periodic weekdays 00:00 to 23:59 class redir2

   seq 10 permit ip host 10.3.29.3 any class CLASS1 condition 100

1.13   show port

show port [all]

1.13.1   Purpose

Displays a list of ports that are present or configured in the system.

1.13.2   Command Mode

all modes

1.13.3   Syntax Description

all

Optional. For any SmartEdge router except the SmartEdge 100 router, includes ports that are configured but are not present on the system. For SmartEdge 100 routers, displays all ports on the carrier card, regardless of whether the associated media interface cards (MICs) are available.

all

Optional. Includes ports that are configured but are not present on the system.

1.13.4   Default

Displays only ports that are present on the system.

1.13.5   Usage Guidelines

Use the show port command to display a list of ports that are present or configured in the system.

Table 4 describes the values for the State field that can be displayed for a given port on a SmartEdge 400 or SmartEdge 800 router.

Table 4    Port States for SmartEdge 400 and SmartEdge 800 RoutersSmartEdge Router

State

Description

Up

Port is configured to be up, and it is up.

Down

Port is configured, and it is down.

Down—not entitled

Port is on the low-density version of the traffic card and is not available.

Unconfigured

Port is unconfigured and down.

Table 5 describes the values for the State field that can be displayed for a given port on a SmartEdge 100 router.

Table 5    Port States for SmartEdge 100 Routers

State

Description

Up

The carrier card and associated MIC are configured and physically present. The port is configured and successfully passing traffic.

Down

The carrier card and associated MIC are configured and physically present. The port is configured but is not successfully passing traffic.

No card

The carrier card and associated MIC are configured but not physically present, and the specified port has been configured.

No MIC

The carrier card and associated MIC have been configured and the specified port has been configured, but the MIC is not physically present.

Unavailable

The carrier card is configured and may or may not be physically present, but either the associated MIC has not been configured or the configured MIC does not support the specified port.

Unconfigured

The carrier card and associated MIC are configured and may or may not be physically present, but the specified port has not been configured.

For more information about low-density traffic cards, see Configuring Cards.

Note:  
By default, most show commands (in any mode) display information for the current context only or, depending on the command syntax, for all contexts. If you are an administrator for the local context, you can insert the optional context ctx-name construct, preceding the show command, to view output for the specified context without entering that context. For more information about using the context ctx-name construct, see the context command description.

Note:  
By appending a space followed by the pipe ( | ) character at the end of a show command, you can filter the output using a set of modifier keywords and arguments. For more information, see “Modifying Output of show Commands” in Using the CLI.

1.13.6   Examples

The following example displays the list of all ports that are present in a SmartEdge 800 router. In this example, the 4-port Gigabit Ethernet traffic card is a low-density, 2-port version; ports 2 and 4 are unavailable:

[local]Redback>show port all
Slot/Port:Ch.SubCh  Type                 State

 2/1                oc12                 Unconfigured

 2/2                oc12                 Unconfigured

 2/3                oc12                 Unconfigured

 2/4                oc12                 Unconfigured

 4/1                ethernet             Up

 4/2                ethernet             Up

 4/3                ethernet             Up

 4/4                ethernet             Up

 7/1                ethernet             Up

 9/1                ethernet             Up

 9/2                ethernet             Down - not entitled

 9/3                ethernet             Up

 9/4                ethernet             Down - not entitled

1.14   show port counters

For ports on channelized OC-12 or STM-1 traffic cards, the syntax is:

show port counters [persistent] [slot/port[:chan-num[:sub-chan-num]]] [detail | live | queue]

For channelized ports on DS-3 or E1 traffic cards, the syntax is:

For all other traffic cards and all media interface cards (MICs), the syntax is:

show port counters [persistent] [slot/port] [detail | live | queue]

1.14.1   Purpose

Displays the counters associated with system ports and channels.

1.14.2   Command Mode

all modes

1.14.3   Syntax Description

persistent

Optional. If omitted, displays values since the counters were last cleared or the card was last reloaded. If specified, displays values since the system was last reloaded.

slot

Optional. Chassis slot number of the traffic card for which counters are displayed.

port

Required if you enter the slot argument. Port number for which counters are displayed. The range of values depends on the type of card or MIC.

chan-num

Optional. Channel number or which counters are displayed. If omitted, displays counters for all channels on the specified port. The range of values depends on the type of port; see Table 6 for the range of values.

sub-chan-num

Optional. Subchannel number channel for which counters are displayed. If omitted, displays counters for all subchannels in the specified channel. The range of values depends on the type of port; see Table 6 for the range of values.

detail

Optional. Displays more detailed counter information.

live

Optional. Forces the retrieval of live data for summary counters.

queue

Optional. Displays per-queue information kept by Packet Processing ASIC (PPA) counters; the values reflect the count since the last policy change.

1.14.4   Default

Displays last known values of summary counters for all ports.

1.14.5   Usage Guidelines

Use the show port counters command to display counters associated with system ports with values that have been accumulated since the counters were last cleared with the clear port counters command (in exec mode) or the traffic card was last reloaded.

Use the persistent keyword to display the counters with values accumulated since the system was last reloaded.

Note:  

The value for the port argument on the SmartEdge 100 router is either of the following:


Table 6 lists the range of values for the chan-num and sub-chan-num arguments for various types of channelized ports.

Table 6    Range of Values for the chan-num and sub-chan-num Arguments

Port

Channel Types

chan-num Range

sub-chan-num Range

Channelized OC-12

DS-3, DS-1

1 to 12

1 to 28

Channelized STM-1

E1, DS-0 channel group

1 to 63

1 to 31

Channelized DS-3

DS-1

1 to 28

Channelized E1

DS-0 channel group

1 to 31

If you specify the optional slot, or port, or chan-num arguments, the display shows counter information for the specified traffic card, or port, or channel; if you specify the optional sub-chan-num argument, the output displays counter information for just that subchannel.

If you specify the optional slot or port arguments, the display shows counter information for the specified traffic card or port.

By default, this command displays only summary counter information for all ports with their last known values, which have been cached; cached values are updated every 60 seconds. Use the live keyword to force the system to read and display the current values for the summary counters.

Table 7 describes the summary counter information that is displayed for all port types if the detail keyword is not specified.

Table 7    Summary Counters

Field

Description

packets sent

Number of packets sent

packets recvd

Number of packets received

send packet rate

Number of packets per second sent

recv packet rate

Number of packets per second received

rate refresh interval

Applies only to rate counters; interval (seconds) over which rates have been calculated

bytes sent

Number of bytes sent

bytes recvd

Number of bytes received

send bit rate

Number of bits per second sent

recv bit rate

Number of bits per second received

Table 8 describes the PPA and packet drop counters, which are displayed for all types of ports when you specify the detail keyword; the data displayed for these counters, with the exception of the rate counters, is live, not cached data.

Table 8    PPA and Packet Drop Counters

Field

Description

PPA Port Counters

packets sent

Number of packets sent

packets recvd

Number of packets received

send packet rate

Number of packets per second sent

recv packet rate

Number of packets per second received

IP mcast pks rcv

Number of multicast packets received

IP mcast pks snt

Number of multicast packets sent

rate refresh interval

Applies only to rate counters; interval (seconds) over which rates have been calculated

bytes sent

Number of bytes sent

bytes recvd

Number of bytes received

send bit rate

Number of bits per second sent

recv bit rate

Number of bits per second received

IP mcast bytes rcv

Number of multicast bytes received

IP mcast bytes snt

Number of multicast bytes sent

PPA Input Error Counters

idc other errors

Number of packets received with other errors, as reported by the FPGA

idc overrun errors

Number of packets received that overran the input descriptor cache

no cct packets

Number of packets received that do not belong to any circuit

cct down pkts

Number of packets dropped because the circuit is down

unknown encap pkts

Number of packets received for which the packet encapsulation is incorrect for the circuit

unreach pkts

Number of packets dropped because no destination route entry exists for the destination IP address

media filter pkts

Number of packets with an unsupported media protocol

crc port errors

Number of packets received with CRC errors

idc abort errors

Number of packets received with a line-signaled abort

no cct bytes

Number of bytes received that do not belong to any circuit

cct down bytes

Number of bytes dropped because the circuit is down

unknown encap byte

Number of bytes received for which the byte encapsulation is incorrect for the circuit

unreach bytes

Number of bytes dropped because no destination route entry exists for the destination IP address

media filter bytes

Number of bytes with an unsupported media protocol

PPA Output Error Counters

WRED drop packets

Number of packets dropped by the WRED feature

adj drop packets

Number of packets dropped due to adjacency errors or missing adjacency

tail drop packets

Number of packets dropped because the egress queue is full

adj drop packets

Number of bytes dropped due to adjacency errors or missing adjacency

Packet Drop Counters

not IPv4 drop pkts

Number of packets dropped that are marked with an unsupported IP version

unhandled IP optns

Number of packets dropped due to unsupported IP options

bad IP checksum

Number of packets dropped due to an invalid checksum on the packet

link layer bcast

Number of link layer broadcast packets dropped

bad IP length

Number of packets dropped due to an invalid checksum on the packet

Table 9 describes the policing counters that are displayed for all types of ports, except for Ethernet ports, when you specify the detail keyword.

Table 9    Policing Counters

Field

Description

conform pkts

Number of packets that conform to the rate-limiting policy on incoming traffic

conform drop pkts

Number of packets that conform to the rate-limiting policy but were dropped

exceed pkts

Number of packets that exceed the rate defined by the rate-limiting policy

exceed drop pkts

Number of packets that exceed the rate defined by the rate-limiting policy and were dropped

conform bytes

Number of bytes that conform to the rate-limiting policy on incoming traffic

conform drop bytes

Number of bytes that conform to the rate-limiting policy but were dropped

exceed bytes

Number of bytes that exceed the rate defined by the rate-limiting policy

exceed drop bytes

Number of bytes that exceed the rate defined by the rate-limiting policy and were dropped

Note:  

For counters for ATM ports:


Table 10 describes the optical data that is displayed for POS and channelized optical ports when you specify the detail keyword.

Table 10    POS Physical Layer Counters and Status

Field

Description

Active Alarms

Lists the active alarms, if any:

  • N/A—Not applicable to this type of port

  • NONE—No alarms are present

Sonet Section

LOS

Number of loss of signal occurrences detected by the section

LOF

Number of loss of frame occurrences detected by the section

BIP-B1

Number of Bit Interleaved Parity error conditions (value of the B1 byte) detected by the section

Sonet Line

AIS

Number of alarm indication signal occurrences detected by the line

RDI

Number of remote defect indication signal occurrences detected by the line

BIP-B2

Number of Bit Interleaved Parity error conditions (value of the B2 byte) detected by the line

FEBE

Number of far end block error conditions detected by the line

Sonet Path

AIS

Number of alarm indication signal occurrences detected by the path

RDI

Number of remote defect indication signal occurrences detected by the path

BIP-B3

Number of Bit Interleaved Parity error conditions (value of the B3 byte) detected by the path

FEBE

Number of far end block error conditions detected by the path

LOP

Number of loss of pointer conditions detected by the path

Received Sonet Overhead

F1

Value of the F1 byte

K1

Value of the K1 byte

K2

Value of the K2 byte

S1

Value of the S1 byte

C2

Value of the C2 byte

Transmitted Sonet Overhead

F1

Value of the F1 byte

K1

Value of the K1 byte

K2

Value of the K2 byte

S1

Value of the S1 byte

C2

Value of the C2 byte

Table 11 lists the general, transmit, and receive counters that are displayed for Ethernet ports when the detail keyword is specified. These counters are displayed in addition to the PPA and packet drop counters.

Table 11    Ethernet Port Counters

Field

Description

General Counters

packets sent

Total number of multicast and broadcast packets transmitted without any errors

bytes sent

Number of bytes transmitted in good packets plus the number of bytes transmitted in packets with errors

mcast packets sent

Number of multicast packets that are transmitted without any errors

bcast packets sent

Number of broadcast packets transmitted without any errors

dropped pkts out

Number of packets dropped during transmission

pending pkts out

Number of packets queued during transmission

port drops out

Number of packets dropped on the egress port due to exceeding the rate limit as defined by the metering policy applied on that port

packets recvd

Total number of multicast and broadcast packets with lengths between 64 bytes and the maximum packet size received without any errors

bytes recvd

Number of bytes received in good packets plus the number of bytes received in packets with errors

mcast packets recvd

Number of multicast packets with lengths between 64 bytes and the maximum packet size received without any errors

bcast packets recvd

Number of broadcast packets with lengths between 64 bytes and the maximum packet size received without any errors

dropped pkts in

Number of packets dropped during reception

pending pkts in

Number of packets queued during reception

port drops in

Number of packets dropped on the ingress port due to exceeding the rate limit as defined by the metering policy applied on that port

Transmit Counters

late collision

Number of transmission abortions due to a collision occurring after transmission of packets that are 64 bytes in length

underflow

Number of packets transmitted with an error due to transmit FIFO underflow or txerr signal assertion

regular collision

Total number of regular collision events occurring during transmission

single collision

Number of packets transmitted without any error following a single collision

multiple colls

Number of packets transmitted without any error following multiple collisions

excessive colls

Number of packets that have experienced 16 consecutive collisions or more

deferred

Number of packets deferred upon the first transmit attempt due to a busy line

flow control

Number of correct transmitted flow-control packets

error pkts sent

Number of packets transmitted with an error due to transmit FIFO underflow or txerr signal assertion plus number of regular collision events occurring during transmission

error bytes sent

Number of bytes transmitted in packets with errors

eth 64 octets

Number of transmitted packets, 64 bytes in length, including bad packets

eth 65-127 octs

Number of transmitted packets, 65 to 127 bytes in length, including bad packets

eth 128-255 octs

Number of transmitted packets, 128 to 255 bytes in length, including bad packets

eth 256-511 octs

Number of transmitted packets, 256 to 511 bytes in length, including bad packets

eth 512-1023 octs

Number of transmitted packets, 512 to 1,023 bytes in length, including bad packets

eth 1024-1518 octs

Number of transmitted packets, 1,024 to 1,518 bytes in length, including bad packets

eth > 1518 octs

Number of transmitted packets with length larger than 1,519 bytes, including bad packets

Receive Counters

jabber

Number of packets, larger than the maximum packet size, received with a CRC error

false carrier

Number of false carriers

runt frames

Number of frames received without SFD detection but with carrier assertion

undersized frames

Number of packets, less than 64 bytes in length, received without any error

oversized frames

Number of packets, larger than the maximum packet size, received without any error

crc errors

Number of packets with lengths between 64 bytes and the maximum packet size, received with an integral number of bytes and a CRC error

alignment errors

Number of packets with lengths between 64 bytes and the maximum packet size, received with a nonintegral number of bytes and a CRC error

symbol errors

Number of received packets during which PHY symbol errors were detected

error pkts rcvd

Total of the following counters:

  • Runt Frames

  • Number of packets less than 64 bytes in length, received with a CRC error

  • Undersized Frames

  • Alignment Errors

  • CRC Errors

  • Oversized Errors

  • Number of packets, larger than the maximum packet size, received with a CRC error

  • Symbol Errors

error bytes rcvd

Number of bytes received in packets with errors

flow control

Number of correct received flow-control packets

overflows

Number of receive packets not fully accepted due to receive FIFO overflow or ingress queue overflow

overflow bytes

Number of bytes not reported for all card types(1)

eth 64 octets

Number of received packets, 64 bytes in length, including bad packets

eth 65-127 octs

Number of received packets, 65 to 127 bytes in length, including bad packets

eth 128-255 octs

Number of received packets, 128 to 255 bytes in length, including bad packets

eth 256-511 octs

Number of received packets, 256 to 511 bytes in length, including bad packets

eth 512-1023 octs

Number of received packets, 512 to 1,023 bytes in length, including bad packets

eth 1024-1518 octs

Number of received packets, 1,024 to 1,518 bytes in length, including bad packets

eth > 1518 octs

Number of received packets with length larger than 1,519 bytes, including bad packets

(1)  This field is only available for oversubscribable traffic cards that support propagation of QoS at the port level.

Table 12 describes the Point-to-Point Protocol (PPP) over Ethernet (PPPoE) counters that are displayed for Ethernet ports.

Table 12    PPP and PPPoE Counters for Ethernet Ports

Field

Description

control pkts

Number of control packets received

bad session pkts

Number of session packets received with an invalid session ID

padt sent pkts

Number of PADT packets sent

padr drop pkts

Number of PADR packets dropped

padi drop pkts

Number of PADI packets dropped

padt drop pkts

Number of PADT packets dropped

bad code pkts

Number of unsupported PPPoE discovery packets received

Table 13 describes the counters that are displayed for each queue for the ports specified by the input parameters when you specify the queue keyword. If no queue policy is attached to a port, no per-queue information is displayed.

Table 13    Queue Counters

Field

Description

Queue

Queue number: 0 to 7

Depth

Maximum number of packets allowed for this queue (configured)

Pkts/Bytes Sent

Packets and bytes sent on this queue

WRED Drops

Number of packets dropped by the WRED feature on this queue

Tail Drops

Number of packets dropped because this queue is full

Note:  
By default, most show commands (in any mode) display information for the current context only or, depending on the command syntax, for all contexts. If you are an administrator for the local context, you can insert the optional context ctx-name construct, preceding the show command, to view output for the specified context without entering that context. For more information about using the context ctx-name construct, see the context command description.

Note:  
By appending a space followed by the pipe ( | ) character at the end of a show command, you can filter the output using a set of modifier keywords and arguments. For more information, see “Modifying Output of show Commands” in Using the CLI.

1.14.6   Examples

The following example displays summary counter information for POS port 1 in slot 1; the detailed counters are shown after this example:

[local]Redback>show port counters 1/1
Port            Type                

1/1             pos                  

packets sent       : 49621              bytes sent         : 1091662   

packets recvd      : 49620              bytes recvd        : 1091640   

send packet rate   : 0                  send bit rate      : 16        

recv packet rate   : 0                  recv bit rate      : 16        

rate refresh interval : 60 seconds

The following example displays detailed counters for port 1 on the POS traffic card in slot 1:

[local]Redback>show port counters 1/1 detail



Counters for port pos 1/1 - Interval: 5d 17:58:07



PPA Port Counters

packets sent       : 49628              bytes sent         : 1091816   

packets recvd      : 49627              bytes recvd        : 1091794   

send packet rate   : 0                  send bit rate      : 16        

recv packet rate   : 0                  recv bit rate      : 16        

IP mcast pkts rcv  : 0                  IP mcast bytes rcv : 0         

IP mcast pkts sent : 0                  IP mcast bytes snt : 0         

rate refresh interval : 60 seconds

PPA Input Counters

idc other errors   : 0                  crc port errors    : 0         

idc overrun errors : 0                  idc abort errors   : 0         

no cct packets     : 0                  no cct bytes       : 0          

cct down pkts      : 0                  cct down bytes     : 0         

unknown encap pkts : 0                  unknown encap byte : 0         

unreach pkts       : 0                  unreach bytes      : 0         

media filter pkts  : 0                  media filter bytes : 0         



PPA Output Counters

WRED drop pkts     : 0                  tail drop pkts     : 0         

adj drop pkts      : 0                  adj drop bytes     : 0         



Packet Drop Counters

not IPv4 drop pkts : 0                  bad IP checksum    : 0         

unhandled IP optns : 0                  link layer bcast   : 0         

bad IP length      : 0                   



Policing Counters

conform pkts       : 0                  conform bytes      : 0         

conform drop pkts  : 0                  conform drop bytes : 0         

exceed pkts        : 0                  exceed bytes       : 0         

exceed drop pkts   : 0                  exceed drop bytes  : 0         



Packet-Over-Sonet physical layer statistics

Active Alarms              : NONE



Sonet Section

     LOS : 0                  LOF : 0                  BIP-B1 : 0



Sonet Line

     AIS : 0                  RDI : 0                  BIP-B2 : 158

    FEBE : 111



Sonet Path

     AIS : 0                  RDI : 0                  BIP-B3 : 0

    FEBE : 0                  LOP : 0                 

Received Sonet Overhead

      F1 : 0x0                 K1 : 0x0                    K2 : 0x0

      S1 : 0x0                 C2 : 0x16                



Transmitted Sonet Overhead

      F1 : 0x0                 K1 : 0x0                    K2 : 0x0

      S1 : 0x0                 C2 : 0x16 

The following example displays detailed counters for port 1 on the Ethernet traffic card in slot 5:

[local]Redback>show port counters 5/1 detail
Counters for port ethernet 5/1 - Interval: 5d 15:05:38



PPA Port Counters

packets sent       : 3                  bytes sent         : 126       

packets recvd      : 0                  bytes recvd        : 0         

send packet rate   : 0                  send bit rate      : 0         

recv packet rate   : 0                  recv bit rate      : 0         

IP mcast pkts rcv  : 0                  IP mcast bytes rcv : 0         

IP mcast pkts sent : 0                  IP mcast bytes snt : 0         

rate refresh interval : 60 seconds



PPA Input Error Counters

idc other errors   : 0                  crc port errors    : 0         

idc overrun errors : 0                  idc abort errors   : 0         

no cct packets     : 0                  no cct bytes       : 0         

cct down pkts      : 0                  cct down bytes     : 0         

unknown encap pkts : 0                  unknown encap byte : 0         

unreach pkts       : 0                  unreach bytes      : 0         

media filter pkts  : 0                  media filter bytes : 0         



PPA Output Error Counters

WRED drop pkts     : 0                  tail drop pkts     : 0         

adj drop pkts      : 0                  adj drop bytes     : 0         



Packet Drop Counters

not IPv4 drop pkts : 0                  bad IP checksum    : 0         

unhandled IP optns : 0                  link layer bcast   : 0         

bad IP length      : 0                   



General Counters

packets sent       : 3                  packets recvd      : 0         

bytes sent         : 192                bytes recvd        : 0         

mcast pkts sent    : 0                  mcast pkts recvd   : 0         

bcast pkts sent    : 3                  bcast pkts recvd   : 0         

dropped pkts out   : 0                  dropped pkts in    : 0         

pending pkts out   : 0                  pending pkts in    : 0         

port drops out     : 0                  port drops in      : 0         



Transmit Counters

jabber             : 0                  error pkts sent    : 0         

false carrier      : 0                  error bytes sent   : 0         

late collision     : 0                  eth 64 octets      : 3         

underflow          : 0                  eth 65-127 octs    : 0         

regular collision  : 0                  eth 128-255 octs   : 0         

single collision   : 0                  eth 256-511 octs   : 0         

multiple colls     : 0                  eth 512-1023 octs  : 0         

excessive colls    : 0                  eth 1024-1518 octs : 0         

deferred           : 0                  eth > 1518 octs    : 0         

flow control       : 0                   



Receive Counters

runt frames        : 0                  overflows          : 0         

undersized frames  : 0                  eth 64 octets      : 0         

oversized frames   : 0                  eth 65-127 octs    : 0         

crc errors         : 0                  eth 128-255 octs   : 0         

alignment errors   : 0                  eth 256-511 octs   : 0         

symbol errors      : 0                  eth 512-1023 octs  : 0         

error pkts rcvd    : 0                  eth 1024-1518 octs : 0         

error bytes rcvd   : 0                  eth > 1518 octs    : 0         

flow control       : 0 

The following example displays detailed counters for port 1 on the ATM traffic card in slot 5:

[local]Redback>show port counters 5/1 detail
Counters for port atm 3/1 - Interval: 5d 15:03:28



PPA Port Counters

packets sent       : 0                  bytes sent         : 0         

packets recvd      : 0                  bytes recvd        : 0         

send packet rate   : 0                  send bit rate      : 0         

recv packet rate   : 0                  recv bit rate      : 0         

IP mcast pkts rcv  : 0                  IP mcast bytes rcv : 0         

IP mcast pkts sent : 0                  IP mcast bytes snt : 0         

rate refresh interval : 60 seconds



PPA Input Counters

idc other errors   : 0                  crc port errors    : 0         

idc overrun errors : 0                  idc abort errors   : 0         

no cct packets     : 0                  no cct bytes       : 0         

cct down pkts      : 0                  cct down bytes     : 0         

unknown encap pkts : 0                  unknown encap byte : 0         

unreach pkts       : 0                  unreach bytes      : 0         

media filter pkts  : 0                  media filter bytes : 0         



PPA Output Counters

WRED drop pkts     : 0                  tail drop pkts     : 0         

adj drop pkts      : 0                  adj drop bytes     : 0         



Packet Drop Counters

not IPv4 drop pkts : 0                  bad IP checksum    : 0         

unhandled IP optns : 0                  link layer bcast   : 0         

bad IP length      : 0                   



Policing Counters

conform pkts       : 0                  conform bytes      : 0         

conform drop pkts  : 0                  conform drop bytes : 0         

exceed pkts        : 0                  exceed bytes       : 0         

exceed drop pkts   : 0                  exceed drop bytes  : 0 

1.15   show port detail

For ports on channelized OC-12 or STM-1 traffic cards, the syntax is:

show port [slot / port[:chan-num[:sub-chan-num]]] [all] detail

For channelized ports on DS-3 or E1 traffic cards, the syntax is:

show port [slot/port[:chan-num]] [all] detail

For all other traffic cards and all media interface cards (MICs), the syntax is:

show port [slot/port] [all] detail

1.15.1   Purpose

Displays the medium access control (MAC) address and other lower-layer settings of a single port, all ports on a card, or all ports in the system.

1.15.2   Command Mode

all modes

1.15.3   Syntax Description

slot

Optional. Chassis slot number of the traffic card or MIC for which information is displayed.

port

Required if you enter the slot argument. Port number for which counters are displayed. The range of values depends on the type of card or MIC.

chan-num

Optional. Channel number for which port information is displayed. If omitted, displays port information for all channels on the specified port. The range of values depends on the type of port; see Table 14 for the range of values.

sub-chan-num

Optional. Subchannel number on the channel for which port information is displayed. If omitted, displays port information for all subchannels in the specified channel. The range of values depends on the type of port; see Table 14 for the range of values.

all

Optional. Includes unconfigured ports in the display.

1.15.4   Default

Displays information for configured ports in the system.

1.15.5   Usage Guidelines

Use the show port detail command to display the MAC address and other lower-layer settings for a single channel, all channels on a port, all ports on a traffic card, or all traffic cards in the system. You can display details such as SFP/Media Type, Line State, and so on. The optional arguments allow you to display only information for the specified card, port, or channel.

Note:  

The value for the port argument on the SmartEdge 100 router is as follows:


Table 14 lists the range of values for the chan-num and sub-chan-num arguments for various types of channelized ports.

Table 14    Range of Values for the chan-num and sub-chan-num Arguments

Port

Channel Types

chan-num Range

sub-chan-num Range

Channelized OC-12

DS-3, DS-1

1 to 12

1 to 28

Channelized STM-1

E1, DS-0 channel group

1 to 63

1 to 31

Channelized DS-3

DS-1

1 to 28

Channelized E1

DS-0 channel group

1 to 31

If you do not include any arguments, the output includes all ports present or configured in the system.

Table 15 lists the output fields for the show port command (in any mode) with the detail keyword. Not all fields apply to all types of ports; the “Type” and “Slot/Port” field names are not displayed in the output.

Table 15    Output Fields for the show port detail Command

Field

Description

Header

Type

port-type or channel-type.

Slot/Port

slot/port—Slot and port numbers for this port.

Ch.SubCh

Channel numbers:

  • ds3-chan-num—DS-3 channel, if appropriate for this port.

  • ds1-chan-num—DS-1 channel, if appropriate for this DS-3 channel.

  • e1-chan-num—E1 channel, if appropriate for this port.

State

Port status (combination of the and fields) for a traffic card:

  • Down—Port has been configured to be up, but is not working.

  • Down—not entitled—Port is on the low-density version of the traffic card and is not available.

  • No card—Port has been configured, but the card is not installed.

  • Unconfigured—Port is not configured and down.

  • Up—Port is working (active).

Port status for a MIC:

  • Up—Carrier card and associated MIC are configured and physically present. The port is configured and successfully passing traffic.

  • Down—Carrier card and associated MIC are configured and physically present. The port is configured but is not successfully passing traffic.

  • No card—Carrier card and associated MIC are configured but not physically present, and the specified port has been configured.

  • No MIC—Carrier card and associated MIC have been configured, and the specified port has been configured, but the MIC is not physically present.

  • Unavailable—Carrier card is configured and may or may not be physically present, but either the associated MIC has not been configured or the configured MIC does not support the specified port.

  • Unconfigured—Carrier card and associated MIC are configured and may or may not be physically present, but the specified port has not been configured.

Port Parameters (in alphabetical order)

Active Alarms

  • getting LOS—Alarm is present.

  • getting ATM LCD—Alarm is present.

  • N/A—Not applicable to this type of port.

  • NONE—No alarms are present.

For a complete list of conditions that can cause an alarm, see Alarms and Probable Causes.

Admin state

State of the port as a result of an operator command:

  • Down—Port is not working.

  • Unconfigured—Port is not configured and down.

  • Up—Port is working (active).

APS Group Name

(Automatic Protection Switching group name

ATM MTU size

nnnnn bytes—Size of the hardware maximum transmission unit (MTU) (not configurable).

ATM Payload Scramble

Condition of scrambling for ATM port (on or off).

Auto negotiation

Two-part string for the setting and state fields. Possible values for the setting field are:

  • enabled

  • disabled

Possible values for the state field are:

  • negotiating—Ethernet drivers are in the process of auto-negotiating with the remote peer

  • success—Auto-negotiation was successful

  • fail—Auto-negotiation failed

  • force—Auto-negotiation failed and the port is in forced mode

  • unknown—This is an error state

The possible combinations of the setting and state fields are:

  • disabled-unknown

  • disabled-negotiating

  • disabled-success

  • disabled-force

  • enabled-unknown

  • enabled-negotiating

  • enabled-success

  • enabled-fail

Bandwidth

nnnnnn kbps—Speed of SONET/SDH port.

nnn.nn Mbps—Effective speed of ATM port.

Cable Length

nnn—Configured length and type (short or long, depending on configured length).

CCOD Mode

State of CCOD mode port listening:

on—Port listening mode is enabled.

off—Port listening mode is disabled.

CCOD Mode

State of CCOD mode port listening:

on—Port listening mode is enabled.

off—Port listening mode is disabled.

Clock Source

global-reference—Port is using the controller clock for transmitting.

Crc

Configured value of the cyclic redundancy check for a SONET/SDH port (16 or 32).

Dampening Count

n—Number of instances this link-dampened port went down and came up within the limits set by the link-dampening command. This count is reset only when the port is removed from the configuration with the no form of the port command (in ATM OC, ATM DS-3, or port configuration mode).

Description

Configured description.

Diag Monitor

  • No—SFP cannot monitor its faults nor report power readings

  • Yes—SFP can monitor its faults and report power readings

DSU Bandwidth

nn.nn Mbps—Bandwidth of configured data service unit (DSU).

DSU Mode

digital-link—Configured vendor of DSU.

DSU Scramble

DSU scramble condition (on or off).

Duplex Mode

  • full—Port condition, Ethernet or Gigabit Ethernet (any version).

  • half—Port condition, 10/100 Ethernet only.

Encapsulation

The encapsulation for this port:

  • 802.1q

  • atm

  • cisco-hdlc

  • ethernet

  • frame-relay

  • ppp

Equipment Loopback

Configured equipment loopback:

  • customer—DS-3 or DS-1 channel responds to remote loopback requests.

  • network—DS-3 or DS-1 channel ignores remote loopback requests.

  • NONE—DS-3 or DS-1 channel ignores remote loopback requests.

FEAC code received

Far-end alarm condition (of the remote system):

  • DS3 LOS.

  • DS3 out of frame (OOF).

  • DS3 alarm indication signal (AIS) received.

  • DS3 Idle Received—The far end box is sending the idle pattern and no other data.

  • Service affecting (SA) equipment failed.

  • Nonservice affecting (NSA) equipment failed.

  • Common equipment failed.

  • N/A or NONE—No alarm condition received.

Flow control

Condition of flow control for Gigabit Ethernet port, any version, (on or off).

Framing

Configured framing for the port:

  • c-bit

  • g751

  • m23

  • ESF

  • SF

  • sdh

  • sonet

Framing Mode

For ATM DS-3 ports only:

  • ADM—ATM direct mapping mode.

  • PLCP—Physical layer convergence protocol mode.

Idle Character

Configured idle character (flags or marks).

Keepalive

State of keepalive timer:

  • Not Set—Keepalive timer is not configured.

  • Set (n sec)—Keepalive timer is set for n seconds.

Line SD BER

10E-5 to 10E-9—Signal degrade bit error rate for SONET/SDH port.

Line SF BER

10E-3 to 10E-5—Signal fail bit error rate for SONET/SDH port.

Line state

Physical state of the line:

  • Down—Port has been configured to be up, but is not working.

  • Down— not entitled—Port is on the low-density version of the traffic card and is not available.

  • No card—Port has been configured, but the card is not installed.

  • Unconfigured—Port is not configured and down.

  • Up—Port is working (active).

Link Dampening

For ATM, Ethernet, and POS ports only. Status of link dampening:

  • enabled—Link dampening is enabled.

  • disabled—Link dampening is disabled.

Link up delay

nnnnn msec—Configured or default value (in milliseconds) for the delay time for down-to-up transitions.

Link down delay

nnnnn msec—Configured or default value (in milliseconds) for the delay time for up-to-down transitions.

Link Distance

For Gigabit Ethernet ports with single-mode fiber (SMF) transceivers (LX or LX70) only. Distance supported by the installed transceiver:

  • n—Distance supported by the transceiver.

  • N/A—No transceiver installed or transceiver does not report the distance supported.

Loopback

Type of loopback:

  • internal—Loops transmit to receive to test the port.

  • line—Loops receive to transmit to test the connection.

  • none, off—Loopback is not enabled.

MAC address

nn:nn:nn:nn:nn:nn—Medium access control address for this port.

Media type(1) (2) (3)

Physical interface:

  • 100Base-TX—10/100 Ethernet or Ethernet management port (at either 10 or 100 Mbps).

  • ds3—ATM DS-3 port.

  • 1000Base-LX—Long reach SFP or Gigabit interface converter (GBIC) transceiver.

  • 1000Base-LX70—Extended reach GBIC transceiver.

  • 1000Base-SX—Short reach SFP or GBIC transceiver.

  • 1000Base-T—Copper-based SFP, or GBIC transceiver or GE port on an FE-GE traffic card.

  • 1000Base-SR—Short reach SFP transceiver.

  • 1000Base-IR—Intermediate reach SFP transceiver.

  • 1000Base-LR—Long reach SFP transceiver.

  • 1000Base-CWDM—Coarse-wavelength-division-multiplexing (CWDM) SFP transceiver.

  • 1000Base-DWDM—Dense-wavelength-division-multiplexing (DWDM) SFP transceiver.

  • 10GE-SR—Short reach XFP transceiver (10GE or OC-192c/STM-64c port).

  • 10GE-IR—Intermediate reach XFP transceiver (OC-192c/STM-64c port).

  • 10GE-LR—Long reach XFP transceiver (10GE or OC-192c/STM-64c port).

  • 10GE-ER—Extended reach XFP transceiver (10GE port).

  • 10GE-ZR—Extreme reach XFP transceiver (10GE or OC-192c/STM-64c port).

  • 10GE-DWDM—Dense-wavelength-division-multiplexing (DWDM) XFP transceiver.

  • No GBIC—GBIC transceiver is not installed in this GE port.

  • No transceiver—XFP transceiver is not installed in this 10GE or OC-192c/STM-64c port.

  • Sonet OCn —OC-n (OC-3c/STM-1c, OC-12c/STM-4c, OC-48c/STM-16c) port.

  • unknown—Unknown type of transceiver is installed in this Gigabit Ethernet port.

Mini-RJ21 Connector

Ports n1-n2—Range of port numbers for this connector on an FE-GE traffic card.

MTU size

nnnn Bytes—Configured size of the MTU for the port.

NAS Port Type

  • Configured network access server (NAS) port type for an ATM DS-3, ATM OC, Ethernet, Gigabit Ethernet, or POS port only. For a list of NAS port types, see Configuring RADIUS.

  • blank—Not configured or not applicable to this port.

Over Subscription Rate

Configured value for over subscription:

  • nnnn%

  • Unlimited

QoS Rate Maximum(4)

QoS port-rate limiting value:(5)

  • 50 to 149 Mbps

  • Payload line-rate (150 Mbps)

Path Alarms

  • N/A—Not applicable to this type of port.

  • NONE—No alarms are present.

For a complete list of conditions that can cause an alarm, see Alarms and Probable Causes.

Path Trace Length

The maximum size that the TX path trace message can be set to.

PPPoE PADO Delay

State of PADO delay:

  • Not set—PADO delay is not configured.

  • Set (n sec)—PADO delay is configured for n seconds.

Rx path-trace

Received path trace data.

Report Only Alarms

State of alarm reporting for an ATM OC port:

  • Path alarms (report only): Payload label mismatch (PLM)

  • Path alarms (report only): Path unequipped (UNEQ)

Alarm is reported, but the port is not shut down.

Scramble

Status of X^43 + 1 payload scrambling for a POS port (on or off).

Speed

  • nnnMbps—Speed of the 10/100 Ethernet port.

  • nnGbps—Speed of the Gigabit Ethernet port (any version).

  • auto—Speed of the 10/100 Ethernet port has been determined by sensing the line.

Support Lossless Large MTU

Status of this FE port on an FE-GE traffic card with regard to guaranteed lossless flow control for jumbo frames:

  • Disabled—Port supports this feature but is not enabled for it.

  • Enabled—Port is enabled for this feature.

  • Not Configurable—Port does not support this feature.

  • Shutdown—Port is a member of a port group that is enabled for this feature and has been shut down because it does not support it.

Temperature

SFP Transceiver temperature

Timeslot

Time slots configured for this channelized DS-3 channel (1 to 24).

Timeslot Speed

Configured speed of DS-0 channels in Kbps (56 or 64).

Tx C2 byte Rx C2 byte

Value of the C2 byte:

  • ATM OC ports—0x13.

  • POS ports—0x16 or 0xcf.

Tx Fault Rx Fault

Fault status for the transmit or receive side of the SFP transceiver installed in this port:

  • LowPwrWarning—Measured power has dropped below the level needed by the transceiver to maintain connectivity without errors.

  • NoFault—No power fault has occurred.

  • PwrFault—Measured power is outside the range displayed in the PwrMin and PwrMax fields by the show hardware command (in any mode) with the detail keyword.

Tx National bit Rx National bit

Value of the national bit (bit 12 of set 1) in the E3 frame:

  • Enabled

  • Disabled

Tx path-trace

Transmitted path trace data.

Tx Pwr measured [dbm](6) Rx Pwr measured [dbm]

Current receiver sensitivity and transmitter output power for the SFP transceiver installed in this port.

Undampened line state

  • Up—Port is working (active).

  • Down—Port has been configured to be up, but is not working.

Vcc Measured

SFP Transceiver Vcc

Wavelength

Center wavelength for the version of the SFP optical transceiver installed in this port:

  • 0.00 [nm]—Wavelength is not reported by this transceiver.

  • nnnn.nn [nm], ITU ch nn—Wavelength and International Telecommunications Union (ITU) channel number (if applicable) for this transceiver version.

For wavelength data for each type of transceiver and its versions, see Transceivers for SmartEdge and SM Family Traffic Cards.

Yellow Alarm Detection

Yellow alarm detection condition (on or off).

Yellow Alarm Generation

Yellow alarm generation condition (on or off).

(1)  Small form-factor pluggable (SFP) transceivers are supported only on the Gigabit Ethernet 3 (GE3), the Gigabit Ethernet 1020 (GE1020), the 8-port ATM OC-3c/STM-1c (atm-oc3e-8-port), and the 4-port POS OC-48c/STM16c (pos-oc48e-4-port) traffic cards.

(2)  Gigabit interface converter (GBIC) transceivers are supported only on first and second versions of the Gigabit Ethernet traffic cards. GBIC transceivers are also supported on the 1-port OC-192c/STM-64c (oc192-1-port) card.

(3)  10-Gbps SFP (OC192 XFP) transceivers are supported only on the 10 Gigabit Ethernet (10GE) traffic card.

(4)  Only supported in hsvc-fair mode on the 8-port ATM OC-3c/STM-1c (atm-oc3e-8-port) traffic card. When executed in vc-fair mode, an error message occurs if executed with any value other than 150 Mbps.

(5)  When Payload line-Rate (150 Mbps) is selected, the actual line-rate received is 149.76 Mbps.

(6)  Measured or reported values meet or exceed the transceiver specifications that are documented in Transceivers for SmartEdge traffic cards.

Note:  
The field names for the Type and Slot/Port fields are not displayed for the show port detail command.

Note:  
By default, most show commands (in any mode) display information for the current context only or, depending on the command syntax, for all contexts. If you are an administrator for the local context, you can insert the optional context ctx-name construct, preceding the show command, to view output for the specified context without entering that context. For more information about using the context ctx-name construct, see the context command description.

Note:  
By appending a space followed by the pipe ( | ) character at the end of a show command, you can filter the output using a set of modifier keywords and arguments. For more information, see “Modifying Output of show Commands” in Using the CLI.

1.15.6   Examples

The following example displays detailed configuration information for port 1 on the POS traffic card in slot 1:

[local]Redback>show port 1/1 detail
pos 1/1 state is Down

Description                : 

Line state                 : Down

Admin state                : Down

Media type                 : Sonet OC12 (SM)

Encapsulation              : cisco-hdlc

MTU size                   : 4470 Bytes

Loopback                   : none

Framing                    : sonet

Speed                      : 622080 kbps

Scramble                   : ON

Crc                        : 32

Tx C2 byte                 : 0x16

Rx C2 byte                 : 0x16

Line SF BER                : 10E-4

Line SD BER                : 10E-7

Keepalive                  : Set (10 sec)

Active Alarms              : N/A

Path Alarms                : N/A

SFP / Media Type           : CWDM / MM

Tx path-trace              : 

    73757065 72636f6d 6d370000 00000000  supercomm7......

    00000000 00000000 00000000 00000000  ................

    00000000 00000000 00000000 00000000  ................

    00000000 00000000 00000000 00000d0a  ................

Rx path-trace        : 

    00000000 00000000 00000000 00000000  ................

    00000000 00000000 00000000 00000000  ................

    00000000 00000000 00000000 00000000  ................

    00000000 00000000 00000000 00000000  ................

The following example displays detailed configuration information for port 1 on an ATM OC traffic card in slot 10; the port has been configured for alarm-report-only (in ATM OC configuration mode):

[local]Redback(config-atm-oc)#show port 10/1 detail



atm 10/1 state is Down

Description :

Line state                 : Down

Admin state                : Down

Link Dampening             : disabled

Undampened line state      : Down

Dampening Count            : 0

Media type                 : Sonet OC12 (SM)

Encapsulation              : atm

NAS Port Type              :

Loopback                   : none

Framing                    : sonet

Speed                      : 622.08 Mbps

Bandwidth                  : 599.04 Mbps

Tx C2 byte                 : 0x13

Rx C2 byte                 : 0x13

Line SF BER                : 10E-4

Line SD BER                : 10E-7

ATM MTU size               : 65527 Bytes

MTU size                   : 4470 Bytes

ATM Payload Scramble       : ON

Over Subscription Rate     : Unlimited

MAC address                : 00:30:88:01:08:18

Clock Source               : card-reference

CCOD Mode                  : default

Report Only Alarms

  Path Alarms (report only): Payload label mismatch (PLM)

                             Path un-equipped (UNEQ-P)

Active Alarms              : N/A

Path Alarms                : N/A

Path Trace Length          : 64 (62 + 2 framing)

Tx Path Trace              :

    52656462 61636b00 00000000 00000000  Redback.........

    00000000 00000000 00000000 00000000  ................

    00000000 00000000 00000000 00000000  ................

    00000000 00000000 00000000 00000d0a  ................

Rx Path Trace              :

    00000000 00000000 00000000 00000000  ................

    00000000 00000000 00000000 00000000  ................

    00000000 00000000 00000000 00000000  ................

    00000000 00000000 00000000 00000000  ................


The following example displays detailed configuration information for port 1 on the ATM DS-3 traffic card in slot 3:

[local]Redback>show port 3/1 detail
atm 3/1 state is Up

Description                : ATM port for Multiprotocol circuits

Line state                 : Up

Admin state                : Up

Media type                 : ds3

Encapsulation              : atm

ATM MTU size               : 65527 Bytes

MTU size                   : 5000 Bytes

Loopback                   : none

Framing                    : c-bit

Framing Mode               : ADM

Speed                      : 44.736 Mbps

Bandwidth                  : 44.21 Mbps

Clock Source               : global-reference

Equipment Loopback         : network

Cable Length               : 349 feet (short)

ATM Payload Scramble       : ON

Over Subscription Rate     : Unlimited

MAC address                : 00:00:00:00:00:00

Active Alarms              : NONE

FEAC code received         : NONE

The bandwidth for an ATM DS-3 port is the port speed minus the framing overhead. It represents the effective speed for user traffic.

The following example displays detailed configuration information for port 2 on the low-density Gigabit Ethernet traffic card in slot 9 with a copper GBIC installed; ports 2 and 4 are unavailable with the current entitlement:

[local]Redback>show port 9/2 detail
ethernet 9/2 state is Down

Description               :

Line state                :Down not entitled

Admin state               :Up

Encapsulation             :ethernet

MTU size                  :1500 Bytes

Speed                     :1000 Mbits/sec

Duplex mode               :full

MAC address               :00:30:88:00:13:1b

Media type                :1000Base-TX

Flow control              :on

Loopback                  :off

The following example displays detailed configuration information for port 1 on the ATM OC-3c/STM-1c traffic card in slot 6:

[local]Redback>show port 6/1 detail
atm 6/1 state is Up

Description                : ATM port for Multiprotocol circuits

Line state                 : Up

Admin state                : Up

Media type                 : Sonet OC3 (SM)

Encapsulation              : atm

Loopback                   : none

Framing                    : sonet

Speed                      : 155.52 Mbps

Bandwidth                  : 149.76 Mbps

Qos Rate Maximum           : 50 Mbps

Tx C2 byte                 : 0x13

Rx C2 byte                 : 0x1

Line SF BER                : 10E-5

Line SD BER                : 10E-8

ATM MTU size               : 65519 Bytes

MTU size                   : 5000 Bytes

ATM Payload Scramble       : ON

Over Subscription Rate     : Unlimited

MAC address                : 00:00:00:00:00:00

Active Alarms              : NONE

The bandwidth for an ATM OC port is the port speed minus the framing overhead. It represents the effective speed for user traffic.

The following example displays detailed configuration information, including the auto-negotiation setting being disabled and the state for Ethernet port 1 in slot 5:

ethernet 5/1 state is Down 

Description : 

Line state : Down 

Admin state : Down 

Link Dampening : disabled 

Undampened line state : Down 

Dampening Count : 0 

Encapsulation : ethernet 

MTU size : 1500 Bytes 

NAS Port Type : 

PPPoE pado delay : Set(2 sec)

Speed : 1 Gbps 

Duplex mode : full 

MAC address : 00:30:88:01:64:b5 

Media type : 1000Base-LX 

Flow control :rx state:    real time state 

Auto-negotiation : off state: n/a

Link Distance : N/A 

Loopback : off 

Wavelength : 1310.00 nm 

Diag Monitor : Yes 

TX Fault : LOW-PWR-ALARM 

RX Fault : LOS-Fault 

TX Pwr measured[dbm] : -40.00 

RX Pwr measured[dbm] : -40.00 

The following example displays detailed configuration information for port 1 on the ATM DS-3 traffic card in slot 3 when auto-negotiation is enabled:

[local]Redback>show port 3/1 detail
atm 3/1 state is Up

Description                : ATM port for Multiprotocol circuits

Line state                 : Up

Admin state                : Up

Media type                 : Sonet OC3 (SM)

Encapsulation              : atm

Auto-negotiation : on state: unknown

Flc negotiated set : tx-rx-or-rx-only state: real time state

force : disabled state: inactive

Flow-control : tx&rx state: n/a

The following example displays detailed port information for port 1 on a atm-oc3e-8-port traffic card in slot 14:

[local]Redback>show port 1/1 detail

atm 14/1 state is Up  

Description                :

Line state                 : Up  

Admin state                : Up

Link Dampening             : disabled

Undampened line state      : Up

Dampening Count            : 0

Media type                 : Sonet OC3 

Encapsulation              : atm

NAS Port Type              : 

Loopback                   : none

Framing                    : sonet

Speed                      : 155.52 Mbps

Bandwidth                  : 149.76 Mbps

Qos Rate Maximum           : Line-Rate

Tx C2 byte                 : 0x13

Rx C2 byte                 : 0x13

Line SF BER                : 10E-4

Line SD BER                : 10E-7

ATM MTU size               : 65527 Bytes

MTU size                   : 4470 Bytes

ATM Payload Scramble       : ON

Over Subscription Rate     : Unlimited

MAC address                : 00:d0:b6:ff:5b:5d

Clock Source               : card-reference

CCOD Mode                  : default

SFP Transceiver Status

Wavelength                : 1310.00 nm

Diag Monitor              : Yes  

Tx Fault                  : No Fault 

Rx Fault                  : No Fault     

Tx Pwr measured[dbm]      : -11.51 

Rx Pwr measured[dbm]      : -10.77 

Temperature               : 39 C     

Vcc Measured              : 3.23 V     

APS Group Name             : N/A

Report Only Alarms 

  Path Alarms (report only): NONE

Active Alarms              : NONE

Path Alarms                : NONE

Path Trace Length          : 64 (62 + 2 framing)

Tx Path Trace              : 

    6c616479 62756700 00000000 00000000  ladybug.........

    00000000 00000000 00000000 00000000  ................

    00000000 00000000 00000000 00000000  ................

    00000000 00000000 00000000 00000000  ................

Rx Path Trace              : 

    00000000 00000000 00000000 00000000  ................

    00000d0a 526f7574 65725465 73746572  ....RouterTester

    2e20506f 72742031 30332f31 2e000000  . Port 103/1....

    00000000 00000000 00000000 00000000  ................

The following example displays detailed port information for port 2 on a ge4-20-port traffic card in slot 2:

[local]Redback>show port 2/2 detail

ethernet 2/2 state is Up

Description                :

Line state                 : Up

Admin state                : Up

Link Dampening             : disabled

Undampened line state      : Up

Dampening Count            : 0

Encapsulation              : ethernet

MTU size                   : 1500 Bytes

NAS Port Type              :

MAC address                : 00:30:88:03:ae:6f

Media type                 : 1000Base-SX

Auto-negotiation           : on                 state: success

Duplex negotiated set   : full               state: full

Flc negotiated set      : tx&rx-or-rx-only   state: rx

force                   : disabled           state: inactive

Speed negotiated set    : 1 Gbps             state: 1 Gbps

Flow control               : rx                 state: n/a

Speed                      : 1 Gbps             state: n/a

Duplex mode                : full               state: n/a

Link Distance              : N/A

Loopback                   : off

SFP Transceiver Status

Wavelength                : 850.00 nm

Diag Monitor              : Yes

Tx Fault                  : No Fault

Rx Fault                  : No Fault

Tx Pwr measured[dbm]      : -4.58

Rx Pwr measured[dbm]      : -3.76

Temperature               : 30 C

Vcc Measured              : 3.15 V

Active Alarms              : NONE


[local]Redback>show port 2/2 detail

Slot/Port:Ch:SubCh  Type                 State

2/1                 ethernet             Up

2/2                 ethernet             Up

2/3                 ethernet             Up

2/4                 ethernet             Up

2/5                 ethernet             Up

2/6                 ethernet             Up

2/7                 ethernet             Down

2/8                 ethernet             Up

2/9                 ethernet             Up

2/10                ethernet             Up

2/11                ethernet             Up

2/12                ethernet             Down

2/13                ethernet             Up

2/14                ethernet             Up

2/15                ethernet             Up

2/16                ethernet             Up

2/17                ethernet             Up

2/18                ethernet             Up

2/19                ethernet             Down

2/20                ethernet             Up

7/1                 ethernet             Up

1.16   show port perf-monitor

For ports on channelized OC-12 or STM-1 traffic cards, the syntax is:

show port perf-monitor slot/port[:chan-num[:sub-chan-num]] [detail [far | near] | far | near]

For channelized ports on DS-3 or E1 traffic cards, the syntax is:

show port perf-monitor slot/port[:chan-num]] [detail [far | near] | far | near]

For clear-channel ports on DS-3, E3, or E1 traffic cards or ports on Asynchronous Transfer Mode (ATM) OC, or ATM DS-3 traffic cards, the syntax is:

show port perf-monitor slot/port [detail [far | near] | far | near]

1.16.1   Purpose

Displays configuration information and performance-monitoring (PM) statistics for one or more ports, channels, or subchannels.

1.16.2   Command Mode

all modes

1.16.3   Syntax Description

slot

Chassis slot number of the traffic card for which configuration information and PM statistics are displayed.

port

Port number for which configuration information and PM statistics are displayed.

chan-num

Optional. Channel number for which configuration information and PM statistics are displayed. If omitted, displays configuration information and PM statistics for all channels on the specified port. The range of values depends on the type of port; see Table 16 for the range of values.

sub-chan-num

Optional. Subchannel number on the channel for which configuration information and PM statistics are displayed. If omitted, displays PM statistics for all subchannels in the specified channel. The range of values depends on the type of port; see Table 16 for the range of values.

detail

Optional. Displays detailed PM information.

far

Optional. Displays far end PM information.

near

Optional. Displays near end PM information; this setting is the default if neither the near nor far keyword is specified.

1.16.4   Default

If no optional arguments or keywords are specified, data is for the near end.

1.16.5   Usage Guidelines

Use the show port perf-monitor command to display configuration information and PM statistics for one or more ports, channels, or subchannels. For definitions of the output fields, see Table 15 in the description of the show port detail command.

Note:  
The SmartEdge 100 router limits the value of the slot argument to 2.

Note:  
The value for the port argument on the SmartEdge 100 router depends on the MIC slot in which the ATM OC MIC is installed.

Table 16 lists the range of values for the chan-num and sub-chan-num arguments for various types of channelized ports.

Table 16    Range of Values for the chan-num and sub-chan-num Arguments

Port

Channel Types

chan-num Range

sub-chan-num Range

Channelized OC-12

DS-3, DS-1

1 to 12

1 to 28

Channelized STM-1

E1, DS-0 channel group

1 to 63

1 to 31

Channelized DS-3

DS-1

1 to 28

Channelized E1

DS-0 channel group

1 to 31

Data is displayed in 15-minute intervals; data for the current interval reflects the elapsed time in the interval. The same data is displayed in both the standard and detailed formats. If you do not specify the detail keyword, the data is shown in tabular format with the abbreviated field names; with the detail keyword, it is present in text format with the field descriptions.

If sub-chan-num is not specified, the PM statistics are displayed for the channel specified by chan-num, and not for the individual subchannels; if sub-chan-num is specified, then the PM statistics are displayed for that channel only.

If you specify the far keyword for an ATM DS-3 or OC port, section data is not displayed.

If you have not enabled the Synchronous Optical Network (SONET) path trace and monitoring features for a first-generation ATM OC traffic card with the sonet eu command (in card configuration mode), path data is not displayed; it is not necessary to enter the sonet eu command for a second-generation ATM OC traffic card or an ATM DS-3 traffic card. To determine if a card has SONET path trace and monitoring features enabled, enter the show chassis command (in any mode), and check for the N flag in the Flags column.

Table 17 lists the statistical data fields that are displayed with this command; not all fields are displayed for all types of channels and ports. If you specify the detail keyword, the same statistical data fields are displayed, but with the description instead of the abbreviation.

Table 17    show port perf-monitor Field Descriptions

Field

Description

BES

Burst errored seconds

CCV

C-bit coding violations

CES

C-bit errored seconds

CSES

C-bit severely errored seconds

CSS

Controlled slip seconds

DM

Degraded minutes

ES

Errored seconds

LCDS

Loss of cell delineation seconds

LCV

Line code violations

LES

Line errored seconds

LSES

Line severely errored seconds

LUAS

Line unavailable seconds

PCV

P-bit coding violations

Path code violations

PES

P-bit errored seconds

Path errored seconds

PLCP SEFS

Physical layer convergence protocol (PLCP) severely errored framing seconds

PLCP UAS

PLCP unavailable seconds

PSES

P-bit severely errored seconds

Path severely errored seconds

PUAS

Path unavailable seconds

SCV

Section code violations

SES

Section errored seconds

SEFS

Severely errored framing seconds

SES

Severely errored seconds

SSES

Section severely errored seconds

SSEFS

Section severely errored framing seconds

UAS

Unavailable seconds

Note:  
Some test equipment can generate time division multiplexing (TDM) code errors such that an E3 port interprets them as a mix of excessive zeros (EXZ) and bipolar violation (BPV) errors, which usually occur in pairs; however, the E3 port considers them a single LCV error as does most legacy equipment.

Note:  
By default, most show commands (in any mode) display information for the current context only or, depending on the command syntax, for all contexts. If you are an administrator for the local context, you can insert the optional context ctx-name construct, preceding the show command, to view output for the specified context without entering that context. For more information about using the context ctx-name construct, see the context command description.

Note:  
By appending a space followed by the pipe ( | ) character at the end of a show command, you can filter the output using a set of modifier keywords and arguments. For more information, see “Modifying Output of show Commands” in Using the CLI.

1.16.6   Examples

The following example displays the configuration information and PM statistics for port 1 on the ATM DS-3 traffic card in slot 3:

[local]Redback>show port perf-monitor 3/1
atm 3/1 state is Up

Description                :

Line state                 : Up

Admin state                : Up

Media type                 : ds3

Encapsulation              : atm

ATM MTU size               : 65527 Bytes

MTU size                   : 4470 Bytes

Loopback                   : none

Framing                    : c-bit

Framing Mode               : ADM

Speed                      : 44.736 Mbps

Bandwidth                  : 44.21 Mbps

Clock Source               : global-reference

Equipment Loopback         : customer

Cable Length               : 349 feet (short)

ATM Payload Scramble       : ON

Over Subscription Rate     : Unlimited

MAC address                : 00:30:88:12:05:01

Active Alarms              : NONE

FEAC code received         : NONE



ATMDS3 PM DATA DISPLAY



INTERVAL      LCV   PCV   CCV   PES  PSES  SEFS   UAS   LES   CES  CSES

348             0     0     0     0     0     0     0     0     0     0

Total           0     0     0     0     0     0     0     0     0     0

24 Hours        0     0     0     0     0     0     0     0     0     0



             PLCP   PLCP

INTERVAL     SEFS   UAS  LCDS

348             0     0     0

Total           0     0     0

24 Hours        0     0     0

The following example displays the configuration information and PM statistics for port 1 on the 4-port ATM OC-3/STM-1c traffic card in slot 11:

[local]Redback>show port perf-monitor 11/1
atm 11/1 state is Up

Description                :

Line state                 : Up

Admin state                : Up

Media type                 : Sonet OC3 (SM)

Encapsulation              : atm

Loopback                   : none

Framing                    : sonet

Speed                      : 155.52 Mbps

Bandwidth                  : 149.76 Mbps

Qos Rate Maximum           : 50 Mbps

Tx C2 byte                 : 0x13

Rx C2 byte                 : 0x13

Line SF BER                : 10E-4

Line SD BER                : 10E-7

ATM MTU size               : 65527 Bytes

MTU size                   : 4470 Bytes

ATM Payload Scramble       : ON

Over Subscription Rate     : Unlimited

MAC address                : 00:30:88:00:3f:08

Clock Source               : global-reference

Active Alarms              : NONE

Path Alarms                : NONE

Path Trace Length          : 64 (62 + 2 framing)

Tx Path Trace              :

    6b696d62 65726c79 00000000 00000000  kimberly........

    00000000 00000000 00000000 00000000  ................

    00000000 00000000 00000000 00000000  ................

    00000000 00000000 00000000 00000d0a  ................

Rx Path Trace              :

    6b696d62 65726c79 00000000 00000000  kimberly........

    00000000 00000000 00000000 00000000  ................

    00000000 00000000 00000000 00000000  ................

    00000000 00000000 00000000 00000d0a  ................



Path and Line Data

INTERVAL      PCV  PSES  PUAS   PES  LCDS   LCV  LSES  LUAS   LES

147             0     1     0     1     1     0     1     0     1

Total           0     1     0     1     1     0     1     0     1

24 Hours        0     1     0     1     1     0     1     0     1



Section Data

INTERVAL      SCV  SSES SSEFS   SES

147             0     1     1     1

Total           0     1     1     1

24 Hours        0     1     1     1

The following example displays the configuration information and PM statistics for a DS-1 channel on a port on a channelized DS-3 traffic card:

[local]Redback>show port perf-monitor 2/1:15
ds1 2/1:15 state is Up

Description                : 

Line state                 : Up

Admin state                : Up

Encapsulation              : cisco-hdlc

MTU size                   : 1500 Bytes

Loopback                   : none

Framing                    : ESF

Crc                        : 16

Clock Source               : global-reference

Idle Character             : flags

Timeslot                   : 1-24

Timeslot Speed             : 64

Yellow Alarm Detection     : ON

Yellow Alarm Generation    : ON

Invert Data                : OFF

Keepalive                  : Set (10 sec)

Equipment Loopback         : customer

Active Alarms              : NONE



INTERVAL      LCV   PCV   CSS  SEFS   LES    DM    ES   BES   SES   UAS

219             0     0     0     0     0     0     0     0     0     0

00:30-00:45     0     0     0     0     0     0     0     0     0     0

00:15-00:30     0     0     0     0     0     0     0     0     0     0

00:00-00:15     0     0     0     0     0     0     0     0     0     0

23:45-00:00     0     0     0     0     0     0     0     0     0     0

23:30-23:45     0     0     0     0     0     0     0     0     0     0

23:15-23:30     0     0     0     0     0     0     0     0     0     0

23:00-23:15     0     0     0     0     0     0     0     0     0     0

22:45-23:00     0     0     0     0     0     0     0     0     0     0

22:30-22:45     0     0     0     0     0     0     0     0     0     0

22:15-22:30     0     0     0     0     0     0     0     0     0     0

22:00-22:15     0     0     0     0     0     0     0     0     0     0

21:45-22:00     0     0     0     0     0     0     0     0     0     0

21:30-21:45     0     0     0     0     0     0     0     0     0     0

21:15-21:30     0     0     0     0     0     0     0     0     0     0

21:00-21:15     0     0     0     0     0     0     0     0     0     0

20:45-21:00     0     0     0     0     0     0     0     0     0     0

20:30-20:45     0     0     0     0     0     0     0     0     0     0

20:15-20:30     0     0     0     0     0     0     0     0     0     0

20:00-20:15     0     0     0     0     0     0     0     0     0     0

19:45-20:00     0     0     0     0     0     0     0     0     0     0

19:30-19:45     0     0     0     0     0     0     0     0     0     0

19:15-19:30     0     0     0     0     0     0     0     0     0     0

19:00-19:15     0     0     0     0     0     0     0     0     0     0

18:45-19:00     0     0     0     0     0     0     0     0     0     0

18:30-18:45     0     0     0     0     0     0     0     0     0     0

18:15-18:30     0     0     0     0     0     0     0     0     0     0

18:00-18:15     0     0     0     0     0     0     0     0     0     0

17:45-18:00     0     0     0     0     0     0     0     0     0     0

17:30-17:45     0     0     0     0     0     0     0     0     0     0

17:15-17:30     0     0     0     0     0     0     0     0     0     0

17:00-17:15     0     0     0     0     0     0     0     0     0     0

16:45-17:00     0     0     0     0     0     0     0     0     0     0

Total           0     0     0     0     0     0     0     0     0     0

24 Hours        0     0     0     0     0     0     0     0     0     0

1.17   show port transceiver

show port slot/port[:ch[:sub]] transceiver

1.17.1   Purpose

Displays detailed information about the transceivers installed in the SmartEdge router, including their current status.

1.17.2   Command Mode

all modes

1.17.3   Syntax Description

slot

Chassis slot number of the traffic card for which transceiver status is displayed.

port

Port number for which counters are displayed. The range of values depends on the type of card or MIC.

ch

Not Applicable. The channel number argument does not apply to this command.

sub

Not Applicable. The subchannel number argument does not apply to this command.

transceiver

Displays transceiver information.

1.17.4   Default

Displays a list of transceivers ports that are present or configured in the system.

1.17.5   Usage Guidelines

Use the show port transceiver command to display detailed information about the transceivers installed in the router, including their current status.

Table 18 describes the values for the State field that can be displayed for a given SFP or XFP transceiver port on a SmartEdge 1200, SmartEdge 800, or SmartEdge 400 router.

Table 18    SFP and XFP Transceiver Port Data Displayed by the show port transceiver Command

State

Description

SFP / Media type

SFP transceivers—Ethernet traffic cards:

  • FX / MM—Short reach transceiver, multimode fiber.

  • LX10 / SM—Long reach transceiver, single-mode fiber.

  • SX / MM—Short reach transceiver, multimode fiber.

  • LX / SM—Long reach transceiver, single-mode fiber.

  • ZX / SM—Extended long reach transceiver, single-mode fiber.

  • T / Cat5—Copper-based transceiver.

  • CWDM / SM—Coarse wavelength-division multiplexing (CWDM) transceiver, single-mode fiber.

  • DWDM / SM—Dense wavelength-division multiplexing (DWDM) transceiver, single-mode fiber.

SFP transceivers—SONET OC-n (OC-3c/STM-1c, OC-12c/STM-4c, and OC-48c/STM-16c) cards

  • SR / SM—Short reach transceiver, single-mode fiber.

  • SR / MM—Short reach transceiver, multimode fiber.

  • IR / SM—Intermediate reach transceiver, single-mode fiber.

  • LR / SM—Long reach transceiver, single-mode fiber.

XFP / Media type

10-Gbps SFP (XFP) transceivers—10-GE and SONET/SDH OC-192 traffic cards:

  • SR / SM—Short reach transceiver, single-mode fiber.

  • SR / MM—Short reach transceiver, multimode fiber.

  • IR / SM—Intermediate reach transceiver, single-mode fiber.

  • LR / SM—Long reach transceiver, single-mode fiber.

  • ER / SM—Extended long reach transceiver, single-mode fiber.

  • ZR / SM—Extreme reach transceiver, single-mode fiber.(1)

  • DWDM / SM—Dense wavelength-division multiplexing (DWDM) transceiver, single-mode fiber.(2)

Redback Approved

State of transceiver testing for transceiver in Redback router:s:

  • No—Redback has not tested.

  • Yes—Redback has tested.

Diagnostic monitoring

Whether the installed transceiver supports diagnostic monitoring compliant to SFF-8472 for SFPs or INF-8077i for XFPs.

CLEI code

Common Language Equipment Identifier (CLEI) code for this transceiver; blank if not applicable for this transceiver.

Serial number

nnnnnnnnnnnnnn—Unique identifier for this transceiver.

Wavelength

Center wavelength for the version of the optical transceiver installed in this port:

  • 0.00 [nm]—Wavelength is not reported by this transceiver.

  • nnnn.nn [nm]—Wavelength for this transceiver version.

Tx Pwr [dbm](3)

Transmitter optical output power (measured, minimum, and maximum limits) for the version of the transceiver installed in this port.

Rx Pwr [dbm]

Receiver optical input power (measured, minimum, and maximum limits) for the version of the transceiver installed in this port.

Temperature [oC]

Temperature (measured, minimum, and maximum limits) in degrees Centigrade.

Laser bias current

Magnitude of the laser bias power setting current (measured, minimum and maximum limits), in milliamperes (mA).

The laser bias provides direct modulation of laser diodes and allows the user to monitor the “health” of the laser.

Vcc [V]

Magnitude of the supply voltage to the transceiver (measured, minimum, and maximum limits), in Volts (V).

AUX1(4) (for XFP transceivers only)

Auxiliary measurement 1 for XFP transceivers—defined in Byte 222 Page 01h in INF-8077i.

AUX2 (for XFP transceivers only)

Auxiliary measurement 2 for XFP transceivers—defined in Byte 222 Page 01h in INF-8077i.

Active alarms(5)

Transceiver alarm conditions for specified port/slot:

  • NONE—No alarm conditions exist

  • Condition—Alarm condition is in effect.

(1)  Use part number XFP-OC192-LR when ordering the XFP transceivers with 10GE ZR functionality.

(2)  In Releases 6.1.4 and 6.1.5, DWDM XFP transceivers support only ITU channels 35,36,37,53,and 54.

(3)  See Alarms and Probable Causes for the lists of alarms and warnings supported by the SFP and XFP transceivers.

(4)  See Table 19 for a list of auxiliary input types monitored by each auxiliary A/D channel of the XFP transceivers.

(5)  The Transceiver alarms will only be indicated here if “[no] system alarm transceiver suppress” has been configured.

Table 19 lists describes which quantities are monitored by each auxiliary A/D channel.

Table 19    XFP Transceivers Measurements and Threshold Values

Description of Physical Device

Value

Auxiliary monitoring not implemented

0000b

APD bias voltage (16-bit value is Voltage in units of 10 mV)

0001b

Reserved

0010b

TEC current (mA) (16-bit value is Current in units of 100 uA)

0011b

Laser temperature (same encoding as module temperature)

0100b

Laser wavelength

0101b

+5V Supply voltage

0110b

+3.3V Supply voltage

0111b

+1.8V Supply voltage

1000b

-5.2V Supply voltage (absolute value encoded as primary voltage monitor)

1001b

+5V Supply current (16-bit Value is Current in 100 uA)

1010b

+3.3V Supply current (16-bit Value is Current in 100 uA)

1101b

+1.8V Supply current (16-bit Value is Current in 100 uA)

1110b

-5.2V Supply current (16-bit Value is Current in 100 uA)

1111b

1.17.6   Examples

Example 1:

The following example displays the data and status for an SFP transceiver. The asterisk beside -13.01* in the Rx Pwr row indicates that the measured value is out of bounds of the Receive Power threshold and has caused a "Transceiver Receive Power Low Alarm.":

[local]Redback#show port 11/3 transceiver


SFP / Media Type        : SX / MM

Redback Approved        : YES

Diagnostic Monitoring   : YES

CLEI code               : VAUIAAWEAA

Serial Number           : F72247020031

Wavelength              : 850.00 [nm]


                                     High          High         Low          Low

                         Measured    Alarm         Warning      Alarm        Warning

------------------------------------------------------------------------------------

Tx Pwr [dbm]             -3.55      -1.00         -2.00         -9.50         -9.00

Rx Pwr [dbm]            -40.00       0.00         -1.00         -13.01*       -12.00

Temperature[C]           33          95            90           -5             0

Laser Bias Current [mA]  7.61        16.00         15.00         2.00          3.00

Vcc [V]                  3.26        3.63           3.58         2.97          3.02


Active Alarms          : Link down

                         Transceiver Receive Power Low Alarm

Example 2:

The following example displays the data and status for an XFP transceiver:

[local]Redback#show port 11/3 transceiver


XFP / Media Type        : LR / SM

Redback Approved        : NO

Diagnostic Monitoring   : YES

CLEI code               : IPUIANWCAA

Serial Number           : UDE03CT

Wavelength              : 1307.00[nm]


                                     High          High         Low          Low

                         Measured    Alarm         Warning      Alarm        Warning

------------------------------------------------------------------------------------

Tx Pwr [dbm]              -1.98       1.50         1.00         -7.00        -6.00

Rx Pwr [dbm]              -40.00      2.50         2.00         -20.00       -18.01

Temperature[C]             19         83           80           -13          -10

Laser Bias Current [mA]    35.00      80.00        75.00         15.00        20.00

AUX1 +3.3V Supply Voltage  3.31       3.63         3.50          3.00         3.10

AUX2 N/A                   N/A        N/A          N/A           N/A          N/A


Active Alarms          : Link down

1.18   show ppp

For ports on channelized OC-12 or STM-1 traffic cards, the syntax is:

show ppp [slot/port[:chan-num[:sub-chan-num]]] [starting | up | down] [summary | detail] [all]

For channelized ports on DS-3 or E1 traffic cards, the syntax is:

show ppp [slot/port[:chan-num]] [starting | up | down] [summary | detail] [all]

For clear-channel ports on DS-3, E3, or E1 traffic cards, or ports on Packet over SONET/SDH (POS) traffic cards, the syntax is:

show ppp [slot/port] [starting | up | down] [summary | detail] [all]

1.18.1   Purpose

Displays the states of one or more Point-to-Point Protocol (PPP) sessions.

1.18.2   Command Mode

all modes

1.18.3   Syntax Description

slot

Optional. Chassis slot number of the traffic card for which PPP session information displays.

Use the slot, port, chan-num, and sub-chan-num arguments to display information only for the PPP sessions on that slot, port, channel, or subchannel.

port

Required if you enter the slot argument. Port number for which PPP sessions are displayed. If not specified, sessions are displayed for all ports in the specified slot.

chan-num

Optional. Channel number for which PPP session information displays. If omitted, displays PPP session information for all channels on the specified port. The range of values depends on the type of port; see Table 20 for the range of values.

sub-chan-num

Optional. Subchannel number for which PPP session information displays. If omitted, displays PPP session information is for all subchannels in the specified channel. The range of values depends on the type of port; see Table 20 for the range of values.

starting

Optional. Specifies that only starting PPP sessions are to be displayed.

up

Optional. Specifies that only PPP sessions for which the Link Control Protocol (LCP) and IP Control Protocol (IPCP) are in the OPENED state are to be displayed.

down

Optional. Specifies that only PPP sessions for which the LCP is in the INITIAL, CLOSED, or STOPPED state are to be displayed.

summary

Optional. Displays summary information for all PPP sessions.

detail

Optional. Specifies that context and Multilink PPP (MP) bundle information is to be displayed.

all

Optional. Specifies that PPP session information in all contexts is shown. This option is available only in the local context.

Use the all keyword in the local context to display information for all PPP sessions in all contexts. In all other contexts, only PPP sessions bound to the current context are shown.

1.18.4   Default

Displays information for all PPP sessions in the current context.

1.18.5   Usage Guidelines

Use the show ppp command to display the states of one or more PPP sessions.

Note:  
The SmartEdge 100 router limits the value of the slot argument to 2.

Note:  

The value for the port argument on the SmartEdge 100 router is one of the following:


Note:  
The value for the port argument on the SmartEdge 100 router depends on the MIC slot in which the ATM OC MIC is installed.

Table 20 lists the range of values for the chan-num and sub-chan-num arguments for various types of channelized ports.

Table 20    Range of Values for the chan-num and sub-chan-num Arguments

Port

Channel Types

chan-num Range

sub-chan-num Range

Channelized OC-12

DS-3, DS-1

1 to 12

1 to 28

Channelized STM-1

E1, DS-0 channel group

1 to 63

1 to 31

Channelized DS-3

DS-1

1 to 28

Channelized E1

DS-0 channel group

1 to 31

Table 21 lists the output fields for the show ppp command with the detail keyword.

Table 21    Field Descriptions for the show ppp Command with detail Keyword

Field

Description

Port/Circuit

Slot, port, channel, subchannel, and circuit identifiers

Unit

Internal identifier

LCP State

Protocol state on this circuit, as defined in RFC 1661, The Point-to-Point Protocol (PPP)

IPCP State

Protocol state on this circuit, as defined in RFC 1661

NLCP State

Protocol state on this circuit, as defined in RFC 1661

MPLSCP State

Protocol state on this circuit, as defined in RFC 1661

Initial Context

Context in which the interface exists for this PPP encapsulated circuit

Note:  
By default, most show commands (in any mode) display information for the current context only or, depending on the command syntax, for all contexts. If you are an administrator for the local context, you can insert the optional context ctx-name construct, preceding the show command, to view output for the specified context without entering that context. For more information about using the context ctx-name construct, see the context command description.

Note:  
By appending a space followed by the pipe ( | ) character at the end of a show command, you can filter the output using a set of modifier keywords and arguments. For more information, see “Modifying Output of show Commands” in Using the CLI.

1.18.6   Examples

The following example shows how to display summary output for PPP sessions in the current context:

[local]Redback>show ppp summary

Wed Jun 30 21:54:29 2005

               Number    LCP    IPCP   NLCP  MPLSCP

Circuit Type   Circuit   Open   Open   Open  Open

------------   -------   ----   ----   ----  ------

 mp circuits   2         2      2      0     0

ppp circuits   2         2      2      0     0



Total circuits: 4  up: 4  down: 0


The following example shows how to display detailed information for PPP sessions that are up for all ports on the traffic card in slot 11:

[local]Redback>show ppp 11 up detail



Wed Jun 30 16:59:38 2005

                                           LCP      IPCP     NLCP     MPLSCP 

Port/Circuit                         Unit  State    State    State    State  

------------------------------------ ----- -------- -------- -------- --------

11/1:1                                   2 Opened   Opened   Initial  

 Initial Context: local

11/2:1                                   3 Opened   Opened   Initial  

 Initial Context: remote


The following example displays output for all PPP sessions in all contexts:

[local]Redback>show ppp all 

Wed Jun 30 21:47:57 2005

                                           LCP      IPCP     NLCP     MPLSCP  

Port/Circuit                         Unit  State    State    State    State   

------------------------------------ ----- -------- -------- -------- --------

6/3                                      4 Opened   Opened   Initial  Initial 

6/4                                      5 Opened   Opened   Initial  Initial 

10/1:1                                   0 Opened   -ML-     -ML-     -ML-    

10/7:1                                   1 Opened   -ML-     -ML-     -ML-    

Link share MP                            2 N/A      Opened   Initial  Initial 

Link share MP                            3 N/A      Opened   Initial  Initial 



Total circuits: 4  up: 4  down: 0

1.19   show ppp counters

show ppp counters [all-contexts | context | detail | summary]

1.19.1   Purpose

Displays statistics for Point-to-Point Protocol (PPP) packets and session counters on the system.

1.19.2   Command Mode

all modes

1.19.3   Syntax Description

all-contexts

Optional. Displays context-specific PPP counters for all contexts. This keyword is available only for administrators authenticated to the local context.

context

Optional. Displays context-specific PPP counters for the current context.

detail

Optional. Displays detailed information for global PPP counters.

summary

Optional. Displays totals for context-specific PPP counters across all contexts. This keyword is available only for administrators authenticated to the local context. The summary keyword adds together the context-specific PPP counters from all contexts.

1.19.4   Default

If no keyword is specified, the global PPP counters are displayed.

1.19.5   Usage Guidelines

Use the show ppp counters command to display statistics for PPP packets and session counters on the system.

Note:  
By default, most show commands (in any mode) display information for the current context only or, depending on the command syntax, for all contexts. If you are an administrator for the local context, you can insert the optional context ctx-name construct, preceding the show command, to view output for the specified context without entering that context. For more information about using the context ctx-name construct, see the context command description.

Note:  
By appending a space followed by the pipe ( | ) character at the end of a show command, you can filter the output using a set of modifier keywords and arguments. For more information, see “Modifying Output of show Commands” in Using the CLI.

1.19.6   Examples

The following example shows how to display the context-specific PPP counters for the current context:

[local]Redback>show ppp counters context

Last cleared: Never

     received: bytes 260, packets 26,

               unsupported packets 0

         sent: bytes 260, packets 26

LCP echo request      : received 26, sent 0, dropped 0

LCP echo response     : received 0, sent 26, dropped 0

LCP protocol reject   : received 0, sent 0, dropped 0


The following example shows how to display global PPP counters:

[local]Redback>show ppp counters



Wed Jun 30 21:56:07 2005

Packet--------------------------------------------------------

 In                       285      Out                     287

Session-------------------------------------------------------

 LCP Up                    72      LCP Down                 68

 IPCP Up                   12      IPCP Down                 6

 Authen Success             0      Authen Failure            0

 Session Up                 0      Session Down              0

SessionControl------------------------------------------------

 Starting                   0      Authenticating            0

 Pended (current)           0      Pended (total)            0

 Packet Drop

  Session pended            0      At Limit                  0

Timeout-------------------------------------------------------

 ConfReq                   85      TermReq                  19

 CHAP Challenge             0      UPAP Listen               0

PacketDropIn--------------------------------------------------

 Session is Down           17      Bad FSM State            32


The following example shows how to display detailed information for global PPP counters:

[local]Redback>show ppp counters detail

Packet--------------------------------------------------------

 In                        40     Out                      40

  ConfReq                  24      ConfReq                 10

  ConfAck                  10      ConfAck                 10

  ConfNak                   0      ConfNak                  4

  ConfRej                   0      ConfRej                 10

  TermReq                   4      TermReq                  2

  TermAck                   2      TermAck                  4

  Authen Proto              6      Authen Proto             6

  other                     0      other                    0

Session-------------------------------------------------------

 LCP Up                     6     LCP Down                  6

 IPCP Up                    4     IPCP Down                 4

 Authen Success             4     Authen Failure            2

 Session Up                 4     Session Down              6

SessionControl------------------------------------------------

 Starting                   0     Authenticating            0

 Pended (current)           0     Pended (total)            0

 Packet Drop

 Session pended             0     At Limit                  0

Timeout-------------------------------------------------------

 ConfReq                    0     TermReq                   4

 CHAP Challenge             0     UPAP Listen               0

PacketDropIn--------------------------------------------------

 Session is Down            1     Bad FSM State             0

DownCause-----------------------------------------------------

 Rcvd TermReq               4     Rcvd PPPoE PADT           0

 No ConfReq Resp            0     No Echo Resp              0

 Authen Failed              2     Session Down              0

 LCP Down                   0     Circuit Down              0

 Port Down                  0     Port Delete               0

1.20   show ppp multilink

show ppp multilink [{all | bundle {bundle-name | mp sess-id}} [detail] | detail | summary ]

1.20.1   Purpose

Displays information for Multilink Point-to-Point Protocol (MP) bundles.

1.20.2   Command Mode

all modes

1.20.3   Syntax Description

all

Optional. Displays information for all MP bundles in all contexts.

bundle

Optional. Displays information for a specific MP bundle.

bundle-name

Name of the MP bundle of DS-1 channels, E1 channels, or E1 ports to be displayed.

mp sess-id

Session ID of the circuit in the MP bundle; the range of values is 1 to 65534.

detail

Optional. Displays additional multilink information.

summary

Optional. Displays a summary of all Point-to-Point Protocol (PPP) and MP sessions for all contexts.

1.20.4   Default

When used without any optional constructs, displays information about all MP bundles in the current context.

1.20.5   Usage Guidelines

Use the show ppp multilink command to display information for MP bundles.

Use the bundle-name argument to specify an MP bundle configured with DS-1 channels, E1 channels, or E1 ports; use the mp sess-id construct to specify an MP bundle created by the system on a PPP-encapsulated or PPP over Ethernet (PPPoE)-encapsulated circuit.

To determine the session ID for an MP bundle, use the show ppp all or show circuit command (in any mode).

Note:  
By default, most show commands (in any mode) display information for the current context only or, depending on the command syntax, for all contexts. If you are an administrator for the local context, you can insert the optional context ctx-name construct, preceding the show command, to view output for the specified context without entering that context. For more information about using the context ctx-name construct, see the context command description.

Note:  
By appending a space followed by the pipe ( | ) character at the end of a show command, you can filter the output using a set of modifier keywords and arguments. For more information, see “Modifying Output of show Commands” in Using the CLI.

1.20.6   Examples

The following example shows how to display information for any MP bundle:

[local]Redback>show ppp multilink
Bundle Name: bar             

  Link Count: 2  Username: (null)

  Our MRRU: 1524 Peer MRRU: 1524

  Our Endpoint-Discriminator: class-1 Redback

  Peer Endpoint-Discriminator: class-1 Redback

Member Links      Status

  5/3             active

  5/1             active

The Link Count field displays the number of links that are up.

The following example shows how to display information for all link groups in all contexts:

[local]Redback>show ppp multilink all
Bundle Name: bar             

  Link Count: 2  Username: (null)

  Our MRRU: 1524 Peer MRRU: 1524

  Our Endpoint-Discriminator: class-1 Redback

  Peer Endpoint-Discriminator: class-1 Redback

 

  Member Links     Status

  5/3              active

  5/1              active

 

Bundle Name: bar2            

  Link Count: 2  Username: (null)

  Our MRRU: 1524 Peer MRRU: 1524

  Our Endpoint-Discriminator: class-1 Redback

  Peer Endpoint-Discriminator: class-1 Redback

 

  Member Links     Status

  5/4              active

  5/2              active

The following example shows how to display summary information only:

[local]Redback>show ppp multilink summary
Wed Jun 30 06:38:05 2005

               NUMBER    LCP    IPCP   NLCP

CIRCUIT TYPE   CIRCUIT   OPEN   OPEN   OPEN

------------   -------   ----   ----   ----

 mp circuits   24        24     3      0   

ppp circuits   0         0      0      0   



Total circuits: 24  up: 24  down: 0

The following example shows how to display information for the bar MP bundle, which is a link group of E1 ports:

[local]Redback>show ppp multilink bundle bar
Bundle Name: bar             

  Link Count: 2  Username: (null)

  Our MRRU: 1524 Peer MRRU: 1524

  Our Endpoint-Discriminator: class-1 Redback

  Peer Endpoint-Discriminator: class-1 Redback

 

  Member Links      Status

  5/3               active

  5/1               active

The following example shows how to display information for an MP bundle on an ATM PVC, using its session ID:

[local]Redback>show ppp multilink bundle mp 1

Bundle Name: MP 1            

  Link Count: 1  Username: a-32@local

  Our MRRU: 1524 Peer MRRU: 1524

  LFI Fragment-Threshold: 256

  Our Endpoint-Discriminator: class-3 00:30:88:00:04:5b

  Peer Endpoint-Discriminator: class-2 10.12.48.103

 

  Member Links                         Status

  3/1 vpi-vci 0 32                     active

The following example shows how to display information about the MP bundle named abc. Because the command includes the detail keyword, the output also gives both the bundle handle (Acct handle) and circuit handle (cct handle) information. Note also that 6/1:1:1 under Member Links gives the port/slot:channel:subchannel of the master link:

[local]Redback>show ppp multilink bundle abc detail

Bundle Name: abc

   Link Count: 1  Username:

   Our MRRU: 1500  Peer MRRU: 1500

   Our Endpoint-Discriminator: class-1 dino

   Peer Endpoint-Discriminator: class-1 dino

   Acct handle: 255/7:1023:63/1/1/2


   Member Links                         Status

   6/1:1:1                              active (master)

   cct handle  : 6/1:1:1/1/1/19

1.21   show pppoe

show pppoe [down | mac | services | session sess-id | starting | subscribers slot[/port] circuit-id | summary | up] [all]

1.21.1   Purpose

Displays Point-to-Point Protocol over Ethernet (PPPoE) information for one or more subscriber circuits.

1.21.2   Command Mode

1.21.3   Syntax Description

down

Optional. Displays PPPoE information for subscriber sessions that are down.

mac

Optional. Displays PPPoE information for a particular Medium Access Control (MAC) address.

services

Optional. Displays PPPoE services currently being advertised.

session sess-id

Optional. Session ID for the subscriber circuit for which PPPoE information is to be displayed; the range of values is 1 to 65535.

starting

Optional. Displays PPPoE information for subscriber sessions that are starting.

subscribers

Optional. Displays a list of subscribers according to the following arguments.

slot

Chassis slot number of a traffic card with the PPPoE-encapsulated circuit for which subscriber sessions are displayed. Available only if you enter the subscribers keyword.

port

Optional. Port number of the PPPoE-encapsulated circuit for which subscriber sessions are displayed. If not specified, sessions are displayed for all PPPoE-encapsulated circuits on the card in the specified slot.

circuit-id

Optional. Circuit identifier, according to one of the constructs listed in Table 22.

summary

Optional. Displays summary information for current context.

up

Optional. Displays PPPoE information for subscriber sessions that are up.

all

Optional. Displays PPPoE information for PPPoE-encapsulated subscriber circuits in all contexts. This option is only available in the local context.

1.21.4   Default

None

1.21.5   Usage Guidelines

Use the show pppoe command to display PPPoE-related information for one or more circuits.

Note:  
The SmartEdge 100 router limits the value of the slot argument to 2.

Note:  

The value for the port argument on the SmartEdge 100 router is one of the following:


Table 22 lists the values for the circuit-id argument.

Table 22    Values for the circuit-id Argument

Construct

Description

vlan-id vlan-id

Virtual LAN (VLAN) tag value for an 802.1Q tunnel or PVC. The vlan-id argument is one of the following constructs:

  • pvc-vlan-id—VLAN tag value of a PVC that is not within an 802.1Q tunnel.

  • tunl-vlan-id—VLAN tag value of a tunnel.

  • tunl-vlan-id:pvc-vlan-id—VLAN tag value for the tunnel followed by the VLAN tag value for the PVC within the tunnel.

The range of values for any VLAN tag value is 1 to 4095.

vpi-vci vpi vci

Virtual path identifier (VPI) and virtual circuit identifier (VCI) for an Asynchronous Transfer Mode (ATM) permanent virtual circuit (PVC). The range of values is 0 to 255 and 1 to 65535, respectively.

Note:  
By default, most show commands (in any mode) display information for the current context only or, depending on the command syntax, for all contexts. If you are an administrator for the local context, you can insert the optional context ctx-name construct, preceding the show command, to view output for the specified context without entering that context. For more information about using the context ctx-name construct, see the context command description.

Note:  
By appending a space followed by the pipe ( | ) character at the end of a show command, you can filter the output using a set of modifier keywords and arguments. For more information, see “Modifying Output of show Commands” in Using the CLI.

1.21.6   Examples

The following example shows how to display summary information:

[local]Redback>show pppoe summary
               NUMBER

CIRCUIT TYPE   CIRCUIT   UP    DOWN

------------   ------- ------ ------

ATM            3         3        0

ETHERNET       0         0        0

DOT1Q          0         0        0

Total circuits: 3 up: 3 down: 0

The following example shows how to display services information:

[local]Redback>show pppoe services
Context: local

Number of domains: 2

        Domain: adsl (not advertise)

        Domain: redback (not advertise)

Context: one

Number of domains: 1

        Domain: pppoe (not advertise)

The following example shows how to display information for all PPPoE circuits in the local context:

[local]Redback>show pppoe
Wed Jun 30 01:38:42 2005

Circuit                             MAC address       Subscriber

----------------------------------------------------------------------

3/1 vpi-vci 0 32 pppoe 2001         00:10:67:00:2a:01 a-32@local

3/1 vpi-vci 0 33 pppoe 2002         00:10:67:00:2a:02 a-33@local

3/1 vpi-vci 0 34 pppoe 2003         00:10:67:00:2a:03 a-34@local

1.22   show pppoe counters

show pppoe counters [detail]

1.22.1   Purpose

Displays summary or detailed statistics for all Point-to-Point Protocol (PPP) over Ethernet (PPPoE)-encapsulated circuits.

1.22.2   Command Mode

all modes

1.22.3   Syntax Description

detail

Optional. Displays detailed statistics.

1.22.4   Default

None

1.22.5   Usage Guidelines

Use the show pppoe counters command to display summary or detailed statistics for all PPPoE-encapsulated circuits.

Note:  
By default, most show commands (in any mode) display information for the current context only or, depending on the command syntax, for all contexts. If you are an administrator for the local context, you can insert the optional context ctx-name construct, preceding the show command, to view output for the specified context without entering that context. For more information about using the context ctx-name construct, see the context command description.

Note:  
By appending a space followed by the pipe ( | ) character at the end of a show command, you can filter the output using a set of modifier keywords and arguments. For more information, see “Modifying Output of show Commands” in Using the CLI.

1.22.6   Examples

The following example shows how to display summary statistics:

[local]Redback>show pppoe counters
Wed Jun 30 01:37:25 2005

PPPoE PAD counters:

-------------------

sent packets             : 4000         recv packets : 4000

dropped packets          : 0

PADI packets             : 2000         PADO packets : 2000

PADR packets             : 2000         PADS packets : 2000

PADT packets             : 0            PADM packets : 0

PADN packets             : 0

The following example shows how to display detailed statistics:

[local]Redback>show pppoe counters detail
Wed Jun 30 08:30:40 2005



PPPoE PAD counters:

-------------------

sent packets             : 4000         recv packets             : 4000

dropped packets          : 0         

PADI packets             : 2000         PADO packets             : 2000

PADR packets             : 2000         PADS packets             : 2000

PADT packets             : 0            PADM packets             : 0   

PADN packets             : 0         



PPPoE invalid discovery packet counters:

----------------------------------------

invalid version/type     : 0            invalid length           : 0   

invalid tag length       : 0            unknown code             : 0   

PADIs non-zero sess-id   : 0            PADRs non-zero sess-id   : 0   

PADT, bad MAC addr       : 0            bad encaps               : 0   

PADR, max sess reached   : 0            PADR, same MAC           : 0   

tags not added, large pkt: 0            recv on down circuit     : 0   

invalid tag name         : 0            invalid tag name accepted: 0   

circuit not created      : 0            circuit not init         : 0   

packet on virtual circuit: 0            non subscriber circuit   : 0   

unknown circuit          : 0            proc restart drops       : 0   



PPPoE virtual circuit counters:

-------------------------------

created virtual circuits : 0            deleted virtual circuits : 0   

combined circuits used   : 4000         combined circuits reset  : 2000

create failed            : 0            delete failed            : 0   

create fail, rcct used   : 0            create fail, no cct      : 0   

create fail, cct init    : 0            create fail, vcct exists : 0   

circuit lookup failures  : 0         



PPPoE PADM error counters:

--------------------------

malformed URLs           : 0            too long expanded URLs   : 0   

too long MOTMs           : 0            bad expansion char       : 0   

PADX on bad circuit      : 0         



PPPoE session counters:

-----------------------

session down cplt recv   : 2000         session down cplt proc   : 2000

stale entry cleanup      : 0            bad state entry cleanup  : 0   

session down sent        : 0 

1.23   show privilege

show privilege

1.23.1   Purpose

Displays the current privilege level for the current exec session.

1.23.2   Command Mode

1.23.3   Syntax Description

This command has no keywords or arguments.

1.23.4   Default

None

1.23.5   Usage Guidelines

Use the show privilege command to display the current (administrator) privilege level for the current exec session.

If you are an administrator at privilege level 10 or higher, you can determine the privilege level of any given command at your level or lower by recursively entering the enable and show ? commands.

For example, if an administer at privilege level 15 enters the show privilege command, all commands at privilege level 15 and lower are listed. If the administrator then enters the enable command for privilege level 14 and the show privilege command again, all commands at privilege level 14 and lower are listed. The administrator can repeat these steps at levels 13, 12, and so on until all privilege levels are listed.

Be aware that this method lists the current privilege levels, which could be different from the default privilege levels. See the privilege command in the Command List for more information.

Note:  
By default, most show commands (in any mode) display information for the current context only or, depending on the command syntax, for all contexts. If you are an administrator for the local context, you can insert the optional context ctx-name construct, preceding the show command, to view output for the specified context without entering that context. For more information about using the context ctx-name construct, see the context command description.

Note:  
By appending a space followed by the pipe ( | ) character at the end of a show command, you can filter the output using a set of modifier keywords and arguments. For more information, see “Modifying Output of show Commands” in Using the CLI.

1.23.6   Examples

The following example displays output from the show privilege command:

[local]Redback>show privilege
Current privilege level is 6

1.24   show process

show process [proc-name] [{crash-info | detail}]

1.24.1   Purpose

Displays current status of one or all processes running on the system.

1.24.2   Command Mode

all configuration modes

1.24.3   Syntax Description

proc-name

Optional. Process for which you want to display information. The value of the proc-name argument can be any one of the keywords listed in Table 23.

crash-info

Optional. Specifies that process crash information is to be monitored.

detail

Optional. Specifies that detailed process information is to be displayed.

1.24.4   Default

When used without any optional constructs, this command displays summary status of all tasks running.

1.24.5   Usage Guidelines

Use the show process command to display current information on a specific category of processes, or on all running processes.

Table 23 lists the keywords for the processes supported by this command.

Table 23    Keywords for Processes

Keyword

Process

aaad

authentication, authorization, and accounting (AAA) process

arp

Address Resolution Protocol (ARP) process

atm

Asynchronous Transfer Mode (ATM) process

bgp

Border Gateway Protocol (BGP) process

bridge

bridge process

clips

clientless IP service selection process

cls

Classifier Manager process

csm

Controller State Manager (CSM) process

cpustats

Display CPU statistics

dhcp

Dynamic Host Configuration Protocol (DHCP) relay/proxy process

dhelperd

DHCP helper daemon

dlm

Download Manager (DLM) process

dns

Domain Name System (DNS) process

dot1q

802.1Q encapsulation process(1)

flowd

flow process(2)

fr

Frame Relay process (3)

gsmp

General Switch Management Protocol (GSMP) process

hr

HTTP redirect process

igmp

Internet Group Management Protocol (IGMP) process

isis

Intermediate System-to-Intermediate System (IS-IS) process

ism

Interface and Circuit State Manager (ISM) process

l2tp

Layer 2 Tunneling Protocol (L2TP) process

ldp

Label Distribution Protocol (LDP) process

lg

link group (LG) process

lm

Label Manager (LM) process

mip

Mobile IP process

mpls_static

Multiprotocol Label Switching (MPLS) static process

msdp

Multicast Source Discovery Protocol (MSDP) process

nat

IP Network Address Translation (NAT) process

nd

neighbor discovery (ND) process

netopd

NetOp process daemon

ntp

Network Time Protocol (NTP) process

odd

on-demand diagnostics (ODD) process

ospf

Open Shortest Path First (OSPF) protocol process

ospf3

OSPF Version 3 (OSPF3) protocol process

ped_parse

process execution descriptor (PED) parse process

pem

privacy-enhanced mail (PEM) process

pim

Protocol Independent Multicast (PIM) process

ppaslog

Packet Processing ASIC (PPA) syslog process

ppp

Point-to-Point Protocol (PPP) process

pppoe

PPP over Ethernet (PPPoE) process

qos

quality of service (QoS) process

rcm

Router Configuration Manager (RCM) process

rib

Routing Information Base (RIB) process

rip

Routing Information Protocol (RIP) process

rpm

Routing Policy Manager (RPM) process

rsvp

Resource Reservation Protocol Traffic Engineering (RSVP-TE) process

snmp

Simple Network Management Protocol (SNMP) process

static

static routing process

stats

statistics process

sysmon

system monitor process

tap

Lawful Intercept (LI) process

tunnel

tunnel management process

vrrp

Virtual Router Redundancy Protocol (VRRP) process

xcd

cross-connect process daemon

(1)  The SmartEdge 100 router does not support 802.1Q.

(2)  Not all controller cards support flow.

(3)  The SmartEdge 100 router does not support Frame Relay.

Note:  
By default, most show commands (in any mode) display information for the current context only or, depending on the command syntax, for all contexts. If you are an administrator for the local context, you can insert the optional context ctx-name construct, preceding the show command, to view output for the specified context without entering that context. For more information about using the context ctx-name construct, see the context command description.

Note:  
By appending a space followed by the pipe ( | ) character at the end of a show command, you can filter the output using a set of modifier keywords and arguments. For more information, see “Modifying Output of show Commands” in Using the CLI.

1.24.6   Examples

The following example displays output from the show process command. The column heading PID stands for process ID:

[local]Redback>show process
Load Average : 1.37 1.39 1.40



NAME          PID    SPAWN    MEMORY  TIME           %CPU   STATE    UP/DOWN

csm         10989        1      544K  00:02:45.10    0.00%  run      02:54:18

rcm         10990        1     2008K  00:00:56.44    0.00%  run      02:54:16

ism         10991        1      504K  00:01:50.71    0.00%  run      02:54:15

rpm         10992        1      404K  00:00:24.31    0.00%  run      02:54:15

rib         10993        1      992K  00:00:45.41    0.00%  run      02:54:15

ntp         10995        1      496K  00:00:40.43    0.00%  run      02:59:29

static      13035        4      444K  00:00:04.34    0.00%  run      02:59:29

isis            0        0        0K  Not Avail      0.00%  demand   02:54:13

rip         12652        1      576K  00:00:11.01    0.00%  run      02:59:29

bgp             0        0        0K  Not Avail      0.00%  demand   02:54:13

igmp            0        0        0K  Not Avail      0.00%  demand   02:54:13

ospf        11089        1      704K  00:34:31.05    0.00%  run      02:59:29

sysmon      10997        1      396K  00:00:32.27    0.00%  run      02:35:08

dns         10998        1      404K  00:00:24.98    0.00%  run      02:35:08

The following example displays output from the show process command with the crash-info keyword:

[local]Redback>show process crash-info 
ME TIME STATUS 

ospf Mon Jan 27 14:05:43 2001 Kill (9) 

ism Mon Jan 27 14:28:26 2001 Kill (9) 

ism Mon Jan 27 14:28:50 2001 Kill (9)

The following example displays output from the show process command with the ism detail keywords:

[local]Redback>show process ism detail 
Process (PID)       : ism (20536)

Spawn count         : 1 

Memory              : 708K 

Time                : 00:00:00.16 

%CPU                : 0.00% 

State               : run 

Up time             : 02:37:15

Heart beat          : Enabled 

Spawn time          : 2 seconds 

Max crashes allowed : 5 

Crash thresh time   : 86400 seconds 

Total crashes        : 0

Images: (Spawns, Max spawns, Version, Path) 

   (*) 1, 3, v1, /usr/redback/bin/ism



Client IPC Endpoints: 

   EP 0100007f 060058fe - RIB-IPC-MSG-EP-NAME:00000000 

   EP 0100007f 060058fe - NTP-ISM-MSG-EP-NAME:00000000



Server IPC Endpoints: 

   EP 0100007f 080058fe - ISM2-CLIENT-NETBYTE-EP-NAME:00000000 

   EP 0100007f 070058fe - ISM2-CLIENT-EP-NAME:00000000 

   EP 0100007f 060058fe - ISM-CLIENT-EP-NAME:00000000 

   EP 0100007f 050058fe - ISM-CONF-EP-NAME:00000000 

The following example displays output from the show process command with the cpustats keyword:

[local]Redback#show process cpustats



Total system CPU % usage (5s, 1m, 5m):  0.00,  0.00,  0.00



Proc/thread name:  5sec  1min  5min    Proc/thread name:  5sec  1min  5min

-----------------------------------

-----------------------------------

        exec_cli:  0.00  0.00  0.00 staticd:  0.00  0.00  0.00

             ndd:  0.00  0.00  0.00              clipsd:  0.00  0.00  0.00

           l2tpd:  0.00  0.00  0.00              pppoed:  0.00  0.00  0.00

            aaad:  0.00  0.00  0.00                pppd:  0.00  0.00  0.00

           statd:  0.00  0.00  0.00            dhelperd:  0.00  0.00  0.00

            oddd:  0.00  0.00  0.00                  lm:  0.00  0.00  0.00

           dhcpd:  0.00  0.00  0.00                pemd:  0.00  0.00  0.00

            dlmd:  0.00  0.00  0.00                clsd:  0.00  0.00  0.00

        ppaslogd:  0.00  0.00  0.00             sysmond:  0.00  0.00  0.00

            arpd:  0.00  0.00  0.00                ribd:  0.00  0.00  0.00

            rpmd:  0.00  0.00  0.00           ped_parse:  0.00  0.00  0.00

            ism2:  0.00  0.00  0.00                 rcm:  0.00  0.00  0.00

             csm:  0.00  0.00  0.00            exec_cli:  0.00  0.00  0.00

              pm:  0.00  0.00  0.00             syslogd:  0.00  0.00  0.00

           inetd:  0.00  0.00  0.00          mount_udrv:  0.00  0.00  0.00

           loggd:  0.00  0.00  0.00           mount_mfs:  0.00  0.00  0.00

       mount_mfs:  0.00  0.00  0.00      ptdstat_thread:  0.00  0.00  0.00

   reboot_thread:  0.00  0.00  0.00             evnt_th:  0.00  0.00  0.00

  sccmem_cleanup:  0.00  0.00  0.00             ioflush:  0.00  0.00  0.00

          reaper:  0.00  0.00  0.00          pagedaemon:  0.00  0.00  0.00

           nfsio:  0.00  0.00  0.00               nfsio:  0.00  0.00  0.00

           nfsio:  0.00  0.00  0.00               nfsio:  0.00  0.00  0.00

            init:  0.00  0.00  0.00

The following example displays output from the show process command with the detail keyword:

[local]Redback#show process detail



Load Average : 1.30 1.30 1.25



==================================================================



Process (PID)       : csm (131)



Spawn count         : 1

Memory              : 5584K

Time                : 00:00:41.29

%CPU                : 0.00%

State               : run

Up time             : 15:01:27

Heart beat          : Enabled

Spawn time          : 2 seconds

Max crashes allowed : 5

Crash thresh time   : 86400 seconds

Total crashes       : 0



Images: (Spawns, Max spawns, Version, Path)

  (*)  1, 3, v1, /usr/siara/bin/csm -se800



Client IPC Endpoints:

    EP 7f000205 c6340001 - MO-RCM-NON-SESS-EP-NAME:00000000

    EP 7f000205 c6340001 - IF_CONF-EP-NAME:00000000

    EP 7f000205 c6340001 - MO-MGR-BSD-PKT-EP-NAME:00000000



Server IPC Endpoints:

    EP 7f000205 c634000a - Active-CSM:00000000

    EP 7f000205 c6340001 - CSM-CONF-EP-NAME:00000000

      Dependent process aaad (149) EP 7f000205 dab3000e

      Dependent process rcm (132) EP 7f000205 caa10001

    EP 7f000205 c6340005 - CSM-PPA-EP-NAME:00000000

    EP 7f000205 c6340003 - CSM-CLIENT-EP-NAME:00000000

      Dependent process ism (133) EP 7f000205 d5860009

      Dependent process VX_IPC (-2066809872) EP 7f000203 04000004



==================================================================



Process (PID)       : rcm (132)



Spawn count         : 1

Memory              : 11704K

Time                : 00:00:10.94

%CPU                : 0.00%

State               : run

---(more)---

........

1.25   show process flowd

show process flowd

1.25.1   Purpose

Displays details of the flow process on the current SmartEdge router.

1.25.2   Command Mode

1.25.3   Syntax Description

This command has no keywords or arguments.

1.25.4   Default

None

1.25.5   Usage Guidelines

Use the show process flowd command to display flow processes on the current SmartEdge router.

Note:  
By default, most show commands (in any mode) display information for the current context only or, depending on the command syntax, for all contexts. If you are an administrator for the local context, you can insert the optional context ctx-name construct, preceding the show command, to view output for the specified context without entering that context. For more information about using the context ctx-name construct, see the context command description.

Note:  
By appending a space followed by the pipe ( | ) character at the end of a show command, you can filter the output using a set of modifier keywords and arguments. For more information, see “Modifying Output of show Commands” in Using the CLI.

1.25.6   Examples

The following example shows how to display the flow processes on the current SmartEdge router:

[local]Redback(config)#show process flowd

NAME		   PID 	 SPAWN		  MEMORY  		TIME		      %CPU	   STATE

flowd		  921	   21		    5920K		00 L:00:14.75 0.00%	  run

1.26   show process lm

show process lm [crash-info | detail | dmalloc-statistics]

1.26.1   Purpose

Displays label manager (LM) process information.

1.26.2   Command Mode

all modes

1.26.3   Syntax Description

crash-info

Optional. Displays LM process crash information.

detail

Optional. Displays detailed information.

dmalloc-statistics

Optional. Displays LM process debug memory allocation statistics.

1.26.4   Default

None

1.26.5   Usage Guidelines

Use the show process lm command to display LM process information.

Note:  
By default, most show commands (in any mode) display information for the current context only or, depending on the command syntax, for all contexts. If you are an administrator for the local context, you can insert the optional context ctx-name construct, preceding the show command, to view output for the specified context without entering that context. For more information about using the context ctx-name construct, see the context command description.

Note:  
By appending a space followed by the pipe ( | ) character at the end of a show command, you can filter the output using a set of modifier keywords and arguments. For more information, see “Modifying Output of show Commands” in Using the CLI.

1.26.6   Examples

The following example displays LM process information:

[local]Redback>show process lm



NAME      PID    SPAWN    MEMORY  TIME           %CPU  STATE   UP/DOWN

lm         41        1     2816K  00:00:01.32   0.00%  run     01:10:40

The following example displays LM process crash information:

[local]Redback>show process lm crash-info



NAME        TIME                      STATUS

lm          Mon Mar 29 13:26:47 2005  Trap (133)

The following example displays detailed LM process information:

[local]Redback>show process lm detail



Process (PID)       : lm (112)



Spawn count         : 2

Memory              : 3016K

Time                : 00:00:00.31

%CPU                : 0.00%

State               : run

Up time             : 00:11:09

Heart beat          : Enabled

Spawn time          : 2 seconds

Max crashes allowed : 5

Crash thresh time   : 86400 seconds

Total crashes       : 0

Last exit status    : Trap (133)



Images: (Spawns, Max spawns, Version, Path)

  (*)  2, 4, v1, /usr/siara/bin/lm



Client IPC Endpoints:

  EP 7f000205 ffdf0007 - LFIB SLOT 03/0:00000000

  EP 7f000205 ffdf0007 - LFIB SLOT 03/1:00000000

  EP 7f000205 ffdf0007 - RSVP-LM_EP-NAME:00000000

  EP 7f000205 ffdf0007 - MPLS-STATIC-LM-EP-NAME:00000000

  EP 7f000205 ffdf0006 - ISM2-MBE-EVIN-EP-NAME:00000000

  EP 7f000205 ffdf0004 - RIB-IPC-MSG-EP-NAME:00000000

  EP 7f000205 ffdf0008 - RSVP-IPC-EP-NAME:00000000

  EP 7f000205 ffdf0006 - ISM2-CLIENT-EP-NAME:00000000

  EP 7f000205 ffdf0004 - RIB-IPC-RT-EP-NAME:00000000



Server IPC Endpoints:

  EP 7f000205 ffdf0009 - LBLMGR-CONF-EP-NAME:00000000

   Dependent process rcm (28) EP 7f000205 fff70001

  EP 7f000205 ffdf0007 - LM-IPC-MSG-EP-NAME:00000000

   Dependent process mpls_static (79) EP 7f000205 ffe00001

   Dependent process rsvp (65) EP 7f000205 ffe10001

   Dependent process ism (29) EP 7f000205 fff90008

   Dependent process rib (32) EP 7f000205 fff80015

   Dependent process EPPA IPC SLOT 3 (-2130509823) EP 7f000a43 0001000f

   Dependent process IPPA IPC SLOT 3 (-2147287039) EP 7f000a03 00010010

   Dependent process ism (29) EP 7f000205 fff90007

The following example displays LM process debug memory allocation statistics:

[local]Redback>show process lm dmalloc-statistics



process: lm, pid: 38

dmalloc_logfile: /flash/dmalloc_log38

open file /flash/dmalloc_log38 failed

1.27   show pseudowire

show pseudowire

1.27.1   Purpose

Displays whether enhanced pseudowire load balancing is enabled or disabled on a router.

1.27.2   Command Mode

all modes

1.27.3   Syntax Description

This command has no keywords or arguments.

1.27.4   Default

None

1.27.5   Usage Guidelines

Use the show pseudowire command to display whether enhanced pseudowire load balancing is enabled or disabled on a router.

Use the pseudowire load balancing command in global configuration mode to enable enhanced pseudowire load balancing on a router. To disable enhanced pseudowire load balancing and return the router to the default setting, in which traffic from all channels of a pseudowire traverse the same path, use the no pseudowire load balancing command.

1.27.6   Examples

The following example shows how to display whether pseudowire load balancing is enabled or disabled on the router. In this example, pseudowire load balancing is enabled:

[local]Redback>show pseudowire

multi-path enabled

The following example shows how to display whether pseudowire load balancing is enabled or disabled on the router. In this example, pseudowire load balancing is disabled:

[local]Redback>show pseudowire

multi-path disabled

1.28   show public- key

show public-key admin-name

1.28.1   Purpose

Displays an administrator’s public keys.

1.28.2   Command Mode

1.28.3   Syntax Description

admin-name

Name of the administrator for which public key information is to be displayed.

1.28.4   Default

None

1.28.5   Usage Guidelines

Use the show public-key command to display an administrator’s public keys.

Note:  
By default, most show commands (in any mode) display information for the current context only or, depending on the command syntax, for all contexts. If you are an administrator for the local context, you can insert the optional context ctx-name construct before the show command to view output for the specified context without entering that context. For more information about the context ctx-name construct, see the context command description.

Note:  
By appending a space followed by the pipe ( | ) character at the end of a show command, you can filter the output using a set of modifier keywords and arguments. For more information, see “Modifying Output of show Commands” in Using the CLI.

1.28.6   Examples

The following example displays the public keys configured for the jewel administrator:

[local]Redback>show public-key jewel
DSA public key(s) for user jewel 

RSA public key(s) for user jewel 

1024 35 138778925487550112496264060257494473953477802145777234711904931356017804 25356384229093001105445048536324328024640019971773131984441883108926459349685280 91708337898398915273858795006452667325324989385497793626010262714937340759030252 16457395231727858414474890514861688652497950829684053136276382193869961246761 jewel@pepper 

1.29   show qos agent-circuit-id

show qos agent-circuit-id name [detail]

1.29.1   Purpose

Displays the quality of service (QoS) information for the circuit that matches the specified circuit agent ID.

1.29.2   Command Mode

all modes (10)

1.29.3   Syntax Description

name

Name of the specific circuit agent ID. Alphanumeric string of up to 63 characters.

detail

Optional. Displays details for each circuit agent ID.

1.29.4   Default

When entered without any optional syntax, displays brief QoS information about the circuit.

1.29.5   Usage Guidelines

Use the show qos agent-circuit-id command to display the QoS information for the circuit that matches the specified circuit agent ID.

Note:  
By appending a space followed by the pipe ( | ) character at the end of a show command, you can filter the output using a set of modifier keywords and arguments. For more information, see “Modifying Output of show Commands” in Using the CLI.

1.29.6   Examples

The following example shows the circuit shaping information for the circuit that matches the circuit agent ID dslam2:

[local]Redback>show qos agent-circuit-id dslams

Circuit                   Policy Name         Type     Rate       Source      

5/2 vlan-id 2 pppoe 1021  gold                pwfq     20000      local       

                          meter3              metering 10000      local       

The following example shows details for the circuit agent ID:

[local]Redback>show qos agent-circuit-id dslam2 detail

Circuit: 5/2 vlan-id 2 pppoe 1021

----------------------------------------------------------



Policy Name       : gold              

Policy Type       : pwfq              

Queue position    : 25                Num Queues        : 4                 

Rate              : 20000             Rate Source       : local             



Policy Name       : meter3            

Policy Type       : metering          

Rate              : 10000             Rate Source       : local             

Burst             : 20000             Excess Burst      : 30000 

1.30   show qos circuit

show qos circuit [ circuit-group name] {[slot/port [:chan-num [:sub-chan-num]] {dlci-id | vpi-vci vpi vci | vlan vlan-id} [detail]]}

1.30.1   Purpose

Displays the quality of service (QoS) information for all circuits or a particular circuit in the system.

1.30.2   Command Mode

all modes

1.30.3   Syntax Description

circuit-group name

Optional. Displays the QoS options configured for the specified circuit group.

slot

Optional. Chassis slot number of a traffic card for which circuit information is displayed. If omitted, displays circuit information for all circuits in the system.

port

Optional. Port number for which circuit information is displayed. Required if you enter the slot argument.

chan-num

Optional. Channel number for which circuit information is displayed. If omitted, displays circuit information for all channels on the specified port. The range of values depends on the type of port; see Table 24 for the range of values.

sub-chan-num

Optional. Subchannel number for which circuit information is displayed. If omitted, displays circuit information for all subchannels in the specified channel. The range of values depends on the type of port; see Table 24 for the range of values.

lg lg-id

Optional. Displays all the circuits associated with the specified link or APS group.

dlci-id

Optional. Data-link collection identifier (DLCI) for the Frame Relay permanent virtual circuit (PVC). The range of values is 16 to 991.

vpi-vci vpi vci

Optional. Virtual path identifier (VPI) and virtual channel identifier (VCI) for an Asynchronous Transfer Mode (ATM) PVC. The range of values is 0 to 255 and 1 to 65,535, respectively.

vlan vlan-id

Optional. Virtual LAN (VLAN) tag value for an 802.1Q tunnel or a PVC. The vlan-id argument is one of the following constructs:

  • pvc-vlan-id—VLAN tag value of a PVC that is not within an 802.1Q tunnel.

  • tunl-vlan-id—VLAN tag value of a tunnel.

  • tunl-vlan-id:pvc-vlan-id—VLAN tag value for the tunnel followed by the VLAN tag value for the PVC within the tunnel.

The range of values for any VLAN tag value is 1 to 4,095.

detail

Optional. Displays details for each PVC.

1.30.4   Default

None

1.30.5   Usage Guidelines

Use the show qos circuit command to display the QoS information for all circuits, a particular circuit, or a circuit group in the system.

Table 24 lists the range of values for the chan-num and sub-chan-num arguments for various types of channelized ports.

Table 24    Range of Values for the chan-num and sub-chan-num Arguments

Port

Channel Types

chan-num Range

sub-chan-num Range

Channelized OC-12

DS-3, DS-1

1 to 12

1 to 28

Channelized STM-1

E1, DS-0 channel group

1 to 63

1 to 31

Channelized DS-3

DS-1

1 to 28

Channelized E1

DS-0 channel group

1 to 31

Use the circuit-group name construct to display the QoS options configured for the specified circuit group.

If you enter the optional slot, or port, and chan-num arguments, the command displays circuit information for all circuits configured on the specified card, or port, or channel; if you enter the optional sub-chan-num argument, the command displays circuit information for all circuits configured on the DS-1 channel or DS-0 channel group.

Use the the vpi-vci vpi vci construct to display the VPI and VCI for an ATM PVC and VLAN tag value to display the value of an 802.1Q tunnel or PVC.

Note:  
By appending a space followed by the pipe ( | ) character at the end of a show command, you can filter the output using a set of modifier keywords and arguments. For more information, see “Modifying Output of show Commands” in Using the CLI.

1.30.6   Examples

The following example shows how to display circuit shaping information:

[local]Redback>show qos circuit
Circuit                   Policy Name         Type     Rate       Source 

5/2 vlan-id 2 pppoe 1017  gold                pwfq     20000      local       

                          meter3              metering 10000      local       

5/2 vlan-id 2 pppoe 1018  gold                pwfq     20000      local       

                          meter3              metering 10000      local       

5/2 vlan-id 2 pppoe 1019  gold                pwfq     20000      local       

                          meter3              metering 10000      local       

5/2 vlan-id 2 pppoe 1020  gold                pwfq     20000      local       

                          meter3              metering 10000      local       

5/2 vlan-id 2 pppoe 1021  gold                pwfq     20000      local       

                          meter3              metering 10000      local 

The following example displays detail information about a QoS circuit when an incremental rate adjustment is applied using the rate-adjust dhcp pwfq command. The field, Rate Offset, indicates the incremental rate applied to the circuit (for information about the rate-adjust dhcp pwfq command, see the Command List):

[local]Redback>show qos circuit detail

Circuit: 2/2 vlan-id 2

Policy Name: SAVEMART

Policy Type: pwfq

Rate: 20000 Rate Source: local

Dynamic Parameters

Priority Group 1:

Rate: 4000

Rate Offset: -1000

The following example shows how to display QoS options configured for the cg1 circuit group:

[local]Redback>show qos circuit circuit-group cg1

Circuit                     Policy Name           Type        Rate        Source

circuit-group cg1         meter7               metering    H   -      local

The following example shows how to display detailed information about the QoS options configured for the cgi circuit group:

[local]Redback>show qos circuit circuit-group cg1 detail

circuit-group cg1

----------------------------------------------------------

Policy Name         : policing2

Policy Type         : policing

Hierarchical Type  : Hierarchical Parent

Rate                : 80000              Rate Source        :  local

Burst               : 100000             Excess Burst       :  265000


Policy Name         : metering2

Policy Type         : metering

Hierarchical Type  : Hierarchical Parent

Rate                : 80000              Rate Source        :  local

Burst               : 100000             Excess Burst       :  265000

1.31   show qos class-definition

show qos class-definition [class-definition-name]

1.31.1   Purpose

Displays the contents of quality of service (QoS) class definitions.

1.31.2   Command Mode

exec

1.31.3   Syntax Description

class-definition-name

Optional. An alphanumeric string up to 39 characters that specifies the class definition name.

1.31.4   Default

If you do not specify the class-definition-name argument, a list of all QoS class definitions is displayed. If you specify the class-definition-name argument, detailed information about the specified QoS class definition is displayed.

1.31.5   Usage Guidelines

Use the show qos class-definition command to display the contents of QoS class definitions.

The command output displays a class definition table. This includes all possible packet descriptor (PD) classification values sorted by the priority value (from 0 to 7) and then sorted by the drop precedence value (from 0 to 7). Use the following formula to convert these values to the six-bit values (0 to 63) used to configure PD class definition map entries:

six-bit-value = (8 * priority-value) + drop-value.

Each entry in the table contains either a numerical class ID value from 0 to 7 or a hyphen (-) to indicate that a PD value has not been assigned to the class. After the class definition table is another table that maps class ID values assigned by the system to the class names configured by the administrator.

Note:  
By appending a space followed by the pipe ( | ) character at the end of a show command, you can filter the output using a set of modifier keywords and arguments. For more information, see “Modifying Output of show Commands” in Using the CLI.

1.31.6   Examples

The following example displays a list of all QoS class definitions:

[local]Redback#show qos class-definition

Class Definition                                Id

auo                                              1

rar                                              2

my_classes                                       3

Total QoS class definitions: 3

The following example displays detailed information about the my_classes QoS class definition:

[local]Redback#show qos class-definition my_classes



Class Definition                                Id

my_classes                                       3



   drop value  -  0  -  1  -  2  -  3  -  4  -  5  -  6  -  7  -

 priority 0       -     1     2     3     4     5     6     7  

 priority 1       1     1     2     1     1     1     1     1  

 priority 2       1     1     1     1     1     1     1     1  

 priority 3       1     1     1     1     1     1     1     1  

 priority 4       1     1     1     1     1     1     1     1  

 priority 5       1     1     1     1     1     1     1     1  

 priority 6       1     1     1     1     1     1     1     1  

 priority 7       1     1     1     1     1     1     1     -  



Class   Name                                    Entry Count

 1      default                                          55

 2      two                                               2

 3      three                                             1

 4      four                                              1

 5      five                                              1

 6      six                                               1

 7      seven                                             1



Total QoS class definitions: 1

1.32   show qos class-map

show qos class-map [map-name]

1.32.1   Purpose

Displays quality of service (QoS) classification map information.

1.32.2   Command Mode

all modes

1.32.3   Syntax Description

map-name

Optional. Name of the classification map.

1.32.4   Default

If you do not specify the map-name argument, a list of all classification maps is displayed. If you specify the map-name argument, detailed information about the specified classification map is displayed.

1.32.5   Usage Guidelines

Use the show qos class-map command to display QoS classification map information. Use the optional syntax to narrow the command output.

In command output, a default secondary mapping for inbound QoS packets to Differentiated Services Code Point (DSCP) packets is represented in the table by the string dscp. A custom secondary mapping is indicated by the string cnnnn, where nnnn is the ID number of the secondary class map.

PD and DSCP values are displayed in the format p:d, where p is a priority value from 0 to 7 and d is a drop-precedence value from 0 to 7. To convert these values to the six-bit (0 to 63) values used to configure PD and DSCP classification map entries, use the following formula:

value = (8 * priority-value) + drop-value

Note:  
By appending a space followed by the pipe ( | ) character at the end of a show command, you can filter the output using a set of modifier keywords and arguments. For more information, see “Modifying Output of show Commands” in Using the CLI.

1.32.6   Examples

The following example displays QoS mapping information without specifying a classification map:

[local]Redback#show qos class-map          

Classification Map                        Type      Direction   Id

dscp-to-pd                                ip        in          67

exp-to-pd                                 mpls      in          68

pd-to-exp                                 mpls      out         69

dscp-to-exp                               mpls      out         70



Total QoS classification maps: 4

The following examples display output from the show qos class-map command when a classification map is specified:



[local]Redback#show qos class-map dscp-to-pd

Classification Map                        Type      Direction   Id

dscp-to-pd                                ip        in          66



   drop value  -  0  -  1  -  2  -  3  -  4  -  5  -  6  -  7  -

 priority 0      1:6   0:0   1:6   1:6   1:6   1:6   1:6   1:6 

 priority 1      1:6   1:6   1:6   1:6   1:6   1:6   1:6   1:6 

 priority 2      1:6   1:6   3:1   1:6   1:6   1:6   1:6   1:6 

 priority 3      1:6   1:6   1:6   1:6   1:6   1:6   1:6   1:6 

 priority 4      1:6   1:6   1:6   1:6   1:6   1:6   1:6   1:6 

 priority 5      1:6   1:6   1:6   1:6   1:6   1:6   1:6   1:6 

 priority 6      1:6   1:6   1:6   1:6   1:6   1:6   1:6   1:6 

 priority 7      1:6   1:6   1:6   1:6   1:6   1:6   1:6   1:6 



Total QoS classification maps: 1



[local]Redback#show qos class-map exp-to-pd 

Classification Map                        Type      Direction   Id

exp-to-pd                                 mpls      in          67



          priority:drop

 priority 0      0:0 

 priority 1      4:4 

 priority 2     dscp

 priority 3     c0066

 priority 4      4:6 

 priority 5      4:2 

 priority 6      6:0 

 priority 7      5:6 



Total QoS classification maps: 1



[local]Redback#show qos class-map pd-to-exp    

Classification Map                        Type      Direction   Id

pd-to-exp                                 mpls      out         68



   drop value  -  0  -  1  -  2  -  3  -  4  -  5  -  6  -  7  -

 priority 0       1     0     0     0     0     0     0     0  

 priority 1       1     1     1     1     1     1     1     1  

 priority 2       2     2     2     2     2     2     2     2  

 priority 3       3     3     3     3     3     3     3     3  

 priority 4       4     4     4     4     4     4     4     4  

 priority 5       5     5     5     5     5     5     7     5  

 priority 6       6     6     6     6     6     6     6     6  

 priority 7       7     7     7     7     7     7     7     7  



Total QoS classification maps: 1



[local]Redback#show qos class-map dscp-to-exp 

Classification Map                        Type      Direction   Id

dscp-to-exp                               mpls      out         69



   drop value  -  0  -  1  -  2  -  3  -  4  -  5  -  6  -  7  -

 priority 0     c0068 c0068 c0068 c0068 c0068 c0068 c0068 c0068

 priority 1     c0068 c0068 c0068 c0068 c0068 dscp  c0068 c0068

 priority 2     c0068 c0068 c0068 c0068 c0068 c0068 c0068 c0068

 priority 3     c0068 c0068 c0068 c0068 c0068 c0068   4   c0068

 priority 4     c0068 c0068 c0068 c0068 c0068 c0068 c0068 c0068

 priority 5     c0068 c0068 c0068 c0068 c0068 c0068 c0068 c0068

 priority 6     c0068 c0068 c0068 c0068 c0068 c0068 c0068 c0068

 priority 7     c0068 c0068 c0068 c0068 c0068 c0068 c0068 c0068



Total QoS classification maps: 1

1.33   show qos client

show qos client [{slot slot [{eppa | ippa}]}]

1.33.1   Purpose

Displays quality of service (QoS) Packet Processing ASIC (PPA) client information.

1.33.2   Command Mode

all modes

1.33.3   Syntax Description

slot slot

Optional. Slot number for the ingress or egress PPA.

eppa

Optional. Displays client information for the slot’s egress PPA.

ippa

Optional. Displays client information for the slot’s ingress PPA.

1.33.4   Default

If you enter this command without any optional syntax, client information for all slots, both egress and ingress, is displayed.

1.33.5   Usage Guidelines

Use the show qos client command to display QoS PPA client information. Use the optional syntax to narrow the command output.

Note:  
The SmartEdge 100 router limits the value of the slot argument to 2.

Note:  
By default, most show commands (in any mode) display information for the current context only or, depending on the command syntax, for all contexts. If you are an administrator for the local context, you can insert the optional context ctx-name construct, preceding the show command, to view output for the specified context without entering that context. For more information about using the context ctx-name construct, see the context command description.

Note:  
By appending a space followed by the pipe ( | ) character at the end of a show command, you can filter the output using a set of modifier keywords and arguments. For more information, see “Modifying Output of show Commands” in Using the CLI.

1.33.6   Examples

The following example displays PPA client information without specifying a slot:

[local]Redback>show qos client



Slot#: 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 

iPPA: 

 Dnld: * * * * * * * * *  *  *  *     *  * 

 Reborn: 

 Register:                   * 

ePPA: 

 Dnld: 

 Reborn: 

 Register:                   * 

The following example displays output from the show qos client command when a slot is specified:

[local]Redback>show qos client slot 13



QoS Client on Slot-13 iPPA: 

 Wait for Dnld: n, Wait for reborn n, Registered: y



QoS Client on Slot-13 ePPA: 

 Wait for Dnld: n, Wait for reborn n, Registered: y

1.34   show qos congestion-map

show qos congestion-map map-name

1.34.1   Purpose

Displays the queue assignments for the specified quality of service (QoS) congestion avoidance map.

1.34.2   Command Mode

1.34.3   Syntax Description

map-name

Name of the QoS congestion avoidance map.

1.34.4   Default

None

1.34.5   Usage Guidelines

Use the show qos congestion-map command to display the queue assignments for the specified QoS congestion avoidance map.

Note:  
By default, most show commands (in any mode) display information for the current context only or, depending on the command syntax, for all contexts. If you are an administrator for the local context, you can insert the optional context ctx-name construct, preceding the show command, to view output for the specified context without entering that context. For more information about using the context ctx-name construct, see the context command description.

Note:  
By appending a space followed by the pipe ( | ) character at the end of a show command, you can filter the output using a set of modifier keywords and arguments. For more information, see “Modifying Output of show Commands” in Using the CLI.

1.34.6   Examples

The following example displays the queue assignments for the red-pwfq QoS congestion avoidance map:

[local]Redback>show qos congestion-map red-pwfq



Congestion-Avoidance Map    Type   Mode  Grid  Q-0  1  2  3  4  5  6  7

red-pwfq                    pwfq   RED      1    y



Total QoS congestion-avoidance maps: 1


The following example displays queue parameters for the congestion avoidance map:

[local]Redback#show qos congestion-map test-cmap 



Congestion-Avoidance Map: test-cmap, Type: pwfq, Grid: 1

Queue: 0 , Mode: Random Early Drop

Exp. Weight: 12, Queue Depth (Pkts): 10000

Drop profile: default 

Prob. Min. Threshold Max. Threshold 

10 1000 5000 

Drop profile: profile-1 

Dscp list:

0, 1, 2, 3, 4, 5, 6, 7, 8, 9, 10, 11, 12, 13, 14, 15, 16, 17, 18, 19, 20, 21 

Prob. Min. Threshold Max. Threshold 2000 100 1000 

Drop profile: profile-2 

Dscp list:

33, 34, 35, 36, 37, 38, 39, 40, 41, 42, 43

Prob. Min. Threshold Max. Threshold 

2000 100 1000

Queue: 1 , Mode: Random Early Drop

Queue Depth (Pkts): 65535

Drop profile: default

Prob. Min. Threshold Max. Threshold

32767 1 10000

Drop profile: profile-1

Dscp list:

39, 44, 45, 49, 50, 51, 52, 54

Prob. Min. Threshold Max. Threshold

32767 1 10000



Total QoS congestion-avoidance maps: 1

[local]Redback#

1.35   show qos h-node

show qos h-node [slot slot]

1.35.1   Purpose

Displays quality of service (QoS) hierarchical node information.

1.35.2   Command Mode

all modes

1.35.3   Syntax Description

slot slot

Optional. Slot number for the Gigabit Ethernet (GE) traffic card.

1.35.4   Default

When entered without any optional syntax, the show qos h-node command displays hierarchical node information for all slots.

1.35.5   Usage Guidelines

Use the show qos h-node command to display QoS hierarchical node information. Use the optional slot slot construct to display output for a single Gigabit Ethernet traffic card.

Note:  
The SmartEdge 100 router limits the value of the slot argument to 2.

Note:  
Hierarchical nodes are supported only on traffic-managed ports and circuits.

Note:  
By default, most show commands (in any mode) display information for the current context only or, depending on the command syntax, for all contexts. If you are an administrator for the local context, you can insert the optional context ctx-name construct, preceding the show command, to view output for the specified context without entering that context. For more information about using the context ctx-name construct, see the context command description.

Note:  
By appending a space followed by the pipe ( | ) character at the end of a show command, you can filter the output using a set of modifier keywords and arguments. For more information, see “Modifying Output of show Commands” in Using the CLI.

1.35.6   Examples

The following example displays hierarchical node information for the ports on the GE3 traffic card in slot 13:

[local]Redback>show qos h-node slot 13
Sl/Po L  Name & index/Cct-handle Id   PrId Ccts  M Min-rat/bst   Max-rat/bst   D

13/1  L4 13/1:1023:63/9/0/161    1    0    0     s 0      /0     0      /0



Total QoS hierarchical nodes: 1

1.36   show qos memory

show qos memory

1.36.1   Purpose

Displays quality of service (QoS) daemon memory usage information.

1.36.2   Command Mode

all modes

1.36.3   Syntax Description

This command has no keywords or arguments.

1.36.4   Default

None

1.36.5   Usage Guidelines

Use the show qos memory command to display QoS daemon memory usage information.

Note:  
By default, most show commands (in any mode) display information for the current context only or, depending on the command syntax, for all contexts. If you are an administrator for the local context, you can insert the optional context ctx-name construct, preceding the show command, to view output for the specified context without entering that context. For more information about using the context ctx-name construct, see the context command description.

Note:  
By appending a space followed by the pipe ( | ) character at the end of a show command, you can filter the output using a set of modifier keywords and arguments. For more information, see “Modifying Output of show Commands” in Using the CLI.

1.36.6   Examples

The following example displays output from the show qos memory command:

[local]Redback>show qos memory



Chunk_Size Curr_InUse Max_In_Use TotalAlloc Total_Free Name 

24         0          0          0          0          task_block 

84         3          3          3          0          task_size_block 

196        4          4          4          0          QOS_CKT 

356        0          4          6          6          QOS_CONFQ 

812        2          2          2          0          QOS_POLMAP

1.37   show qos policy

show qos policy

1.37.1   Purpose

Displays information for all configured quality of service (QoS) policies.

1.37.2   Command Mode

all modes

1.37.3   Syntax Description

This command has no keywords or arguments.

1.37.4   Default

None

1.37.5   Usage Guidelines

Use the show qos policy command to display information for all configured QoS policies.

Table 25 describes the output fields for the show qos policy command.

Table 25    show qos policy Field Descriptions

Field Name

Description

Policy-Name

Policy name.

Type

Type of policy.

Grid

Unique policy identifier.

Qs

Number of queues that each circuit consumes when it is bound to this policy. This field applies only to Asynchronous Transfer Mode weighted fair queuing (ATMWFQ), enhanced deficit round-robin (EDRR), and priority queuing (PQ) policies.

Slot

Number of slots where the policy has been downloaded.

Port

Number of circuits currently bound to this policy.

Bound

Indicates the direction of the bound policy: in or out. If there are no bindings, this field is blank.

Dnld

Download in progress. A “Y” entry in this field indicates the policy is being downloaded to a traffic card; otherwise, this field is blank.

Status

Download status. If this field is blank, the policy has been downloaded to the traffic card. An “updt” entry indicates a policy update is pending download. A “del” entry indicates a policy deletion is pending download.

Note:  
By default, most show commands (in any mode) display information for the current context only or, depending on the command syntax, for all contexts. If you are an administrator for the local context, you can insert the optional context ctx-name construct, preceding the show command, to view output for the specified context without entering that context. For more information about using the context ctx-name construct, see the context command description.

Note:  
By appending a space followed by the pipe ( | ) character at the end of a show command, you can filter the output using a set of modifier keywords and arguments. For more information, see “Modifying Output of show Commands” in Using the CLI.

1.37.6   Examples

The following example displays information for all configured QoS policies:

[local]Redback>show qos policy



Policy-Name Type Grid Qs Slot Port Bound DnLd Status 

test         pq  1    8  1    3    out 

special      pq  2    8  1    1    out 



Total QoS policy map: 2

1.38   show qos policy atmwfq

show qos policy atmwfq [{pol-name | default-value}]

1.38.1   Purpose

Displays information about one or more configured quality of service (QoS) Asynchronous Transfer Mode weighted fair queuing (ATMWFQ) policies.

1.38.2   Command Mode

all modes

1.38.3   Syntax Description

pol-name

Optional. Name of an ATMWFQ policy.

default-value

Optional. Displays information about ATMWFQ policy default values.

1.38.4   Default

When entered without any optional syntax, displays brief information about all configured ATMWFQ policies.

1.38.5   Usage Guidelines

Use the show qos policy atmwfq command to display information about one or more configured QoS ATMWFQ policies.

Use the pol-name argument to display detailed information about a single QoS ATMWFQ policy.

Note:  
By default, most show commands (in any mode) display information for the current context only or, depending on the command syntax, for all contexts. If you are an administrator for the local context, you can insert the optional context ctx-name construct, preceding the show command, to view output for the specified context without entering that context. For more information about using the context ctx-name construct, see the context command description.

Note:  
By appending a space followed by the pipe ( | ) character at the end of a show command, you can filter the output using a set of modifier keywords and arguments. For more information, see “Modifying Output of show Commands” in Using the CLI.

1.38.6   Examples

The following example displays brief information about all configured QoS ATMWFQ policies:

[local]Redback>show qos policy atmwfq



Policy-Name          Type   Grid    Qs

atmwfq1              atmwfq 1       4



Total QoS policy map: 1

The following example displays detailed information about the ATMWFQ policy, atmwfq1:

[local]Redback>show qos policy atmwfq atmwfq1



Policy-Name          Type   Grid    Qs

atmwfq1              atmwfq 1       4



Qnum Red    Prob  Weight  Min  Max  Traffic-weight

0    0xf    9     9       5    15   10

1    0xf    9     9       5    15   10

2    0xf    9     9       5    15   10

3    0xf    9     9       5    15   10

The following example displays detailed information for the ATMWFQ policy, ds3_cosq.22001.119.3:

[local]Redback>show qos policy atm ds3_cosq.22001.119.3 



Policy-Name              Type    Grid   Qs 

ds3_cosq.22001.119.3     atmwfq  1      2 



Queue-map: default 

Qnum  Red  Prob   Weight  Min    Max    Traffic-Weight   Mode 

0     0xf  22515  7       10359  10417  361              alternate 

1     0xf  20880  8       638    6176   493



Total policy map: 1

1.39   show qos policy edrr

show qos policy edrr [{pol-name | default-value}]

1.39.1   Purpose

Displays information about one or more quality of service (QoS) enhanced deficit round-robin (EDRR) policies.

1.39.2   Command Mode

all modes

1.39.3   Syntax Description

pol-name

Optional. Name of an EDRR policy.

default-value

Optional. Displays information about EDRR policy default values.

1.39.4   Default

When entered without any optional syntax, displays brief information about all configured EDRR policies.

1.39.5   Usage Guidelines

Use the show qos policy edrr command to display QoS EDRR policy information.

Use the pol-name argument to display detailed information about a single QoS EDRR policy.

Note:  
By default, most show commands (in any mode) display information for the current context only or, depending on the command syntax, for all contexts. If you are an administrator for the local context, you can insert the optional context ctx-name construct, preceding the show command, to view output for the specified context without entering that context. For more information about using the context ctx-name construct, see the context command description.

Note:  
By appending a space followed by the pipe ( | ) character at the end of a show command, you can filter the output using a set of modifier keywords and arguments. For more information, see “Modifying Output of show Commands” in Using the CLI.

1.39.6   Examples

The following example displays brief information about all configured EDRR policies:

[local]Redback>show qos policy edrr



Policy Name    Type   Grid   Qs  slot   Port   Bound   DnLd   Status

drr            edrr   11     8   1      2      Out     

1.40   show qos policy metering

show qos policy metering [{pol-name | default-value}]

1.40.1   Purpose

Displays information about one or more configured quality of service (QoS) metering policies.

1.40.2   Command Mode

all modes

1.40.3   Syntax Description

pol-name

Optional. Name of a metering policy.

default-value

Optional. Displays information about metering policy default values.

1.40.4   Default

When entered without any optional syntax, displays brief information about all configured QoS metering policies.

1.40.5   Usage Guidelines

Use the show qos policy metering command to display information about one or more configured QoS metering policies.

Use the pol-name argument to display detailed information about a single QoS metering policy.

Note:  
By default, most show commands (in any mode) display information for the current context only or, depending on the command syntax, for all contexts. If you are an administrator for the local context, you can insert the optional context ctx-name construct, preceding the show command, to view output for the specified context without entering that context. For more information about using the context ctx-name construct, see the context command description.

Note:  
By appending a space followed by the pipe ( | ) character at the end of a show command, you can filter the output using a set of modifier keywords and arguments. For more information, see “Modifying Output of show Commands” in Using the CLI.

1.40.6   Examples

The following example displays brief information about all QoS metering policies:

[local]Redback>show qos policy metering



Policy-Name          Type   Grid    Qs Slot  Port  Bound  DnLd  Status

meter                meter  1       0  1     5     in               



Total QoS policy map: 1

The following example displays detailed information about the QoS metering policy, meter:

[local]Redback>show qos policy metering meter



Policy-Name          Type   Grid    Qs Slot  Port  Bound  DnLd  Status

meter                meter  1       0  1     5     in               



Slot#:       1   2   3   4   5   6   7   8   9   10   11   12   13   14

iPPA dnld:                                                           

ePPA dnld:                                                           

iPPA ports:                                                 5       

ePPA ports:                                                          



Total QoS policy map: 1

1.41   show qos policy policing

show qos policy policing [{pol-name | default-value}]

1.41.1   Purpose

Displays information about one or more configured quality of service (QoS) policing policies.

1.41.2   Command Mode

all modes

1.41.3   Syntax Description

pol-name

Optional. Name of a policing policy.

default-value

Optional. Displays information about policing policy default values.

1.41.4   Default

When entered without any optional syntax, displays brief information about all configured QoS policing policies.

1.41.5   Usage Guidelines

Use the show qos policy policing command to display information about one or more configured QoS policing policies.

Use the pol-name argument to display detailed information about a single QoS policing policy.

Table 26 describes the output fields for the show qos policy policing command.

Table 26    Field Description for the show qos policy policing Command

Field Name

Description

Policy-Name

Policy name.

Type

Type of policy.

Grid

Unique policy identifier.

Qs

Number of queues that each circuit consumes when it is bound to this policy. This field applies only to Asynchronous Transfer Mode (ATM) weighted fair queuing (WFQ), enhanced deficit round-robin (EDRR), and priority queuing (PQ) policies.

Slot

Number of slots where the policy has been downloaded.

Port

Number of circuits currently bound to this policy.

Bound

Indicates the direction of the bound policy: “in” or “out”. If there are no bindings, this field is blank.

Dnld

Download in progress. A “Y” entry indicates the policy is being downloaded to a traffic card. Otherwise, this field is blank.

Status

Download status. If this field is blank, the policy has been downloaded to the traffic card. An “updt” entry indicates a policy update is pending download. A “del” entry indicates a policy deletion is pending download.

When a policy name is specified, in addition to the information described in Table 26, the distribution of QoS bindings across traffic card slots is displayed.

Note:  
By default, most show commands (in any mode) display information for the current context only or, depending on the command syntax, for all contexts. If you are an administrator for the local context, you can insert the optional context ctx-name construct, preceding the show command, to view output for the specified context without entering that context. For more information about using the context ctx-name construct, see the context command description.

Note:  
By appending a space followed by the pipe ( | ) character at the end of a show command, you can filter the output using a set of modifier keywords and arguments. For more information, see “Modifying Output of show Commands” in Using the CLI.

1.41.6   Examples

The following example displays brief information for all QoS policing policies:

[local]Redback>show qos policy policing



Policy-Name          Type   Grid    Qs Slot  Port  Bound  DnLd  Status

police               police 1       0  1     5     in               



Total QoS policy map: 1

The following example displays detailed information about the QoS policing policy, police, which is bound to 15 circuits on the traffic card in slot 9 and to 15 circuits on the traffic card in slot 11:

[local]Redback>show qos policy policing police 



Policy-Name          Type   Grid    Qs Slot  Port  Bound  DnLd  Status

police               police 6       0  1     30    in           updt



Slot#:       1   2   3   4   5   6   7   8   9   10   11   12   13   14

iPPA dnld:

ePPA dnld:

iPPA ports:                                  15       15

ePPA ports:



Rate(kbps): 2000 Bursts(bytes): 15000



Conf-mark-dscp Conf-drop Exceed-mark-dscp exceed-drop

0x2e           0x0

1.42   show qos policy pq

show qos policy pq [{pol-name | default-value}]

1.42.1   Purpose

Displays information about one or more configured quality of service (QoS) priority queuing (PQ) policies.

1.42.2   Command Mode

all modes

1.42.3   Syntax Description

pol-name

Optional. Name of the PQ policy.

default-value

Optional. Displays information about PQ policy default values.

1.42.4   Default

When entered without any optional syntax, this command displays information about all configured PQ policies.

1.42.5   Usage Guidelines

Use the show qos policy pq command to display information about one or more QoS PQ policies.

Use the pol-name argument to display detailed information about a single QoS PQ policy.

Note:  
By default, most show commands (in any mode) display information for the current context only or, depending on the command syntax, for all contexts. If you are an administrator for the local context, you can insert the optional context ctx-name construct, preceding the show command, to view output for the specified context without entering that context. For more information about using the context ctx-name construct, see the context command description.

Note:  
By appending a space followed by the pipe ( | ) character at the end of a show command, you can filter the output using a set of modifier keywords and arguments. For more information, see “Modifying Output of show Commands” in Using the CLI.

1.42.6   Examples

The following example displays brief information for all QoS PQ policies:

[local]Redback>show qos policy pq default-value 



priority queueing policy default values: 

 number of queues 8 

Qnum Change Red Rate Burst E Prob Weight Min Max Depth 

0               max  max   y 10   9      10  18  1000 

1               max  max   y 10   9      11  18  1000 

2               max  max   y 10   9      12  18  1000 

3               max  max   y 10   9      13  18  1000 

4               max  max   y 10   9      14  18  1000 

5               max  max   y 10   9      15  18  1000 

6               max  max   y 10   9      16  18  1000 

7               max  max   y 10   9      17  18  1000 



( * max=2147483647)

The following example displays detailed information for the PQ policy, special1:

[local]Redback>show qos policy pq special1 



Policy-Name          Type   Grid    Qs Slot  Port  Bound  DnLd  Status

special1             pq     1       8  0     0                  updt



Slot#:    1   2   3   4   5   6   7   8   9  10  11  12  13  14  15  16

iPPA dnld:

ePPA dnld:

iPPA ports:

ePPA ports:



Queues updated: 0, 1, 2, 3, 4, 5, 6, 7, 

Qnum Change Red Rate     Burst  E Prob  Weight  Min Max  Depth 

0    0x0    0x0 1000000  5555   n 100   23      40  900  500 

1    0x0    0x0 50000    1000   y 200   22      50  800  1000 

2    0x0    0x0 max      max    y 300   21      70  700  1000 

3    0x0    0x0 max      max    y 400   20      80  600  1000 

4    0x0    0x0 max      max    y 500   19      90  500  1000 

5    0x0    0x0 max      max    y  10    9      15   18  1000 

6    0x0    0x0 max      max    y  10    9      16   18  1000 

7    0x0    0x0 max      max    y 1 0    9      17   18  1000 



Total QoS policy map: 1

1.43   show qos policy pwfq

show qos policy pwfq [pol-name | default-value]

1.43.1   Purpose

Displays information about one or more configured quality of service (QoS) priority weighted fair queuing (PWFQ) policies.

1.43.2   Command Mode

all modes

1.43.3   Syntax Description

pol-name

Optional. Name of the PWFQ policy.

default-value

Optional. Displays information about PWFQ policy default values.

1.43.4   Default

When entered without any optional syntax, this command displays information about all configured PQ policies in the current context.

1.43.5   Usage Guidelines

Use the show qos policy pwfq command to display information about all PWFQ policies configured in the current context, or to display information about a specific PWFQ policy.

Note:  
PWFQ policies are supported only on traffic-managed ports and circuits.

Note:  
By default, most show commands (in any mode) display information for the current context only or, depending on the command syntax, for all contexts. If you are an administrator for the local context, you can insert the optional context ctx-name construct, preceding the show command, to view output for the specified context without entering that context. For more information about using the context ctx-name construct, see the context command description.

Note:  
By appending a space followed by the pipe ( | ) character at the end of a show command, you can filter the output using a set of modifier keywords and arguments. For more information, see “Modifying Output of show Commands” in Using the CLI.

1.43.6   Examples

The following example displays the values for the pwfq-port PWFQ policy:

[local]Redback>show qos policy pwfq pwfq-port
Policy-Name          Type     Grid    Qs Slots  Ports  Bound  DnLd  Status

pwfq-port            pwfq     12      8  0      0                   updt



Slot#:       1   2   3   4   5   6   7   8   9  10  11  12  13  14

iPPA dnld:

ePPA dnld:

iPPA ports:

ePPA ports:



Max-Q-Depth: 0, Queues updated: none

Queue-map: default

Total policy map: 1

1.44   show qos port

show qos port [slot slot]

1.44.1   Purpose

Displays active quality of service (QoS) binding information for ports on one or more traffic cards.

1.44.2   Command Mode

all modes

1.44.3   Syntax Description

slot slot

Optional. Slot number of traffic card for which QoS binding information is displayed.

1.44.4   Default

When entered without any optional syntax, displays active QoS binding information for ports on all traffic cards.

1.44.5   Usage Guidelines

Use the show qos port command to active display QoS binding information for ports on one or more traffic cards.

Note:  
The SmartEdge 100 router limits the value of the slot argument to 2.

Table 27 describes the output fields for this command.

Table 27    Field Description for the show qos port Command

Field

Description

Slot/Port

Slot and port to which the QoS policy is bound.

(vlan-id)

For QoS policies that are bound to PVCs or subscribers, the PVC number is displayed. Otherwise, this field is blank.

PVC

A “y” entry indicates that the binding is applied to a PVC or to a subscriber. Otherwise, this field is blank.

Policy-Name

Name of bound QoS policy.

Port

Active port to which the QoS policy is bound.

Qpos

Displays the first queue reserved for the QoS binding. This field is applicable only to enhanced deficit round-robin (EDRR) and priority queuing (PQ) policies. For all other QoS policies, this field is blank.

L

Number of queues used for this binding. The value is configured through the EDRR or PQ policy that is bound to the circuit. The value in the Qpos field combined with the value in this field provides the queue numbers. For example, if the Qpos field is 96 and this field is 8, the queues used for the binding are 96, 97, 98, 99, 100, 101, 102, and 103.

Bound

Indicates the direction of the bound policy: “in” or “out”.

L4/L3

Refers to the h-node ID with which the queuing policy is associated.

Note:  
By default, most show commands (in any mode) display information for the current context only or, depending on the command syntax, for all contexts. If you are an administrator for the local context, you can insert the optional context ctx-name construct, preceding the show command, to view output for the specified context without entering that context. For more information about using the context ctx-name construct, see the context command description.

Note:  
By appending a space followed by the pipe ( | ) character at the end of a show command, you can filter the output using a set of modifier keywords and arguments. For more information, see “Modifying Output of show Commands” in Using the CLI.

1.44.6   Examples

The following example shows how to display active binding information for ports on all traffic cards:

[local]Redback>show qos port

Slot/Port (vlan-id)            PVC Policy-Name Bound L4/L3

lg id 25 foo                   y   Policy7     out

lg id 25 vlan-id 1             y   Policy7     in

                                   Policy7     out

lg id 25 vlan-id 2             y   Policy7     out

                                   POLICY2     out

lg id 25 vlan-id 4             y   Policy7     out

lg id 25 vlan-id 5             y   Policy7     out

lg id 25 vlan-id 3             y   Policy7     out

lg id 25 vlan-id 3:1           y   Policy8     out

lg id 25 vlan-id 3:2           y   Policy8     out

lg id 25 vlan-id 3:5           y   Policy7     out

lg id 25 vlan-id 3:6           y   Policy7     out

lg id 25 vlan-id 3:7           y   Policy7     out

lg id 25 vlan-id 3:8           y   Policy7     out

lg id 25 vlan-id 3:9           y   Policy8     out


Total QoS port policy binding: 15 

The following example displays active binding information for ports on a traffic card in slot 5:

[local]Redback>show qos port slot 5

Slot/Port (vlan-id)            PVC Policy-Name Port Qpos  L Bound L4/L3

lg id 25 foo                   y   Policy7     1    4     0 out   1

lg id 25 foo                   y   Policy7     2    5     0 out   2

lg id 25 vlan-id 1             y   POLICY1     1            in    1

                                   Policy7     1    4     0 out   1

lg id 25 vlan-id 2             y   Policy7     1    4     0 out   1

                                   POLICY2     1            out   1

lg id 25 vlan-id 4             y   Policy7     1    36    0 out   1

lg id 25 vlan-id 5             y   Policy7     1    40    0 out   1

lg id 25 vlan-id 3             y   Policy7     1    4     0 out   1

lg id 25 vlan-id 3             y   Policy7     2    5     0 out   2

lg id 25 vlan-id 3:1           y   Policy8     1    44    0 out   5

lg id 25 vlan-id 3:2           y   Policy8     1    48    0 out   6

lg id 25 vlan-id 3:5           y   Policy7     1    56    0 out   5

lg id 25 vlan-id 3:6           y   Policy7     1    60    0 out   7

lg id 25 vlan-id 3:7           y   Policy7     1    64    0 out   8

lg id 25 vlan-id 3:8           y   Policy7     1    68    0 out   9

lg id 25 vlan-id 3:9           y   Policy8     1    80    0 out   10

1.45   show qos port-map

show qos port-map port-map-name [card-type card-type-name] [detail]

1.45.1   Purpose

Displays information about the configured quality of service (QoS) port group maps for all supported card types.

1.45.2   Command Mode

all modes

1.45.3   Syntax Description

port-map-name

Optional. Name of a QoS port group map for which to display information. If not specified, the information displayed is for all port group maps (of a specified card type, if any).

card-type card-type-name

Optional. Name of a traffic card for which QoS port group map information is displayed. If not specified, the information is displayed for all card types. The following are the supported values:

  • carrier—Specifies the Fast Ethernet (FE) or Gigabit Ethernet (GE) media interface cards (MICs) for the SmartEdge 100 router

  • fege-60-2-port—Specifies the Fast Ethernet–Gigabit Ethernet card (60-port FE, 2-port GE)

  • ge-10-port—Specifies the Gigabit Ethernet 1020 (GE1020) card (10-port).

  • ge-20-port—Specifies the Gigabit Ethernet 1020 (GE1020) card (20-port).

  • ge3-4-port—Specifies the Gigabit Ethernet 3 (GE3) card (4-port)

  • ge-5-port—Specifies the Gigabit Ethernet (5-port).

  • ge4-20-port—Specifies the Gigabit Ethernet (GE) card (20-port)

card-type card-type-name

Optional. Name of a traffic card for which QoS port group map information is displayed. If not specified, the information is displayed for all card types. The following are the supported values:

  • fege-60-2-port-sm—Specifies the Fast Ethernet–Gigabit Ethernet card (60-port FE, 2-port GE)

  • ge-10-port-sm—Specifies the Gigabit Ethernet card (10-port).

  • ge-20-port-sm—Specifies the Gigabit Ethernet card (20-port).

  • 10ge-1-port-sm—Specifies the 10 Gigabit Ethernet card (1-port)

  • 10ge-4-port-sm—Specifies the 10 Gigabit Ethernet card (4-port)

detail

Optional. Displays detailed information about the QoS port group maps.

1.45.4   Default

When entered without any optional syntax, displays brief information about all the configured QoS port group maps.

1.45.5   Usage Guidelines

Use the show qos port-map command to display information about the configured QoS port group maps.

1.45.6   Examples

The following example shows how to display information about all configured QoS port group maps:

[local]Redback>show qos port-map

Card Type                Map Type  Map Name

ge3-4-port               default   tm_max_perf

ge3-4-port               predef    fwd_max_perf

ge-10-port               default   tm_max_perf 

ge-10-port               predef    fwd_max_perf

ge-20-port               default   tm_max_perf

ge-20-port               predef    fwd_max_perf

fege-60-2-port           default   tm_fe_perf 

fege-60-2-port           predef    tm_max_perf

ge4-20-port              default   tm_max_perf 

ge4-20-port              predef    fwd_max_perf 

ge-5-port                default   tm_max_perf

ge-10-port               user-def  ge-10-myportmap1

ge-10-port               user-def  ge-10-myportmap2

fege-60-2-port           user-def  fe-60-myportmap1

fege-60-2-port           user-def  fe-60-myportmap2

ge4-20-port              user-def  ge4-20-myportmap1

ge4-20-port              user-def  ge4-20-myportmap2

1.46   show qos port-map bind

show qos port-map bind [slot slot-number] [detail]

1.46.1   Purpose

Displays information about the quality of service (QoS) port group map bindings to traffic cards on the SmartEdge router.

1.46.2   Command Mode

all modes

1.46.3   Syntax Description

slot slot-number

Optional. Chassis slot number of the card for which information about QoS port group map bindings are displayed. The range of values depends on the chassis in which the card is installed. For the SmartEdge 800 router and the SmartEdge 1200 router, the range of values of the slot-number argument for all supported card types are from 1 to 6 and 9 to 14. For the SmartEdge 400 router, the range of values are from 1 to 4.

slot slot-number

Optional. Chassis slot number of the card for which information about QoS port group map bindings are displayed. The range of values is from 1 to 6 and 9 to 14. For the SmartEdge 400 router, the range of values are from 1 to 4.

detail

Optional. Displays detailed information about the QoS port group map binding.

1.46.4   Default

When entered without any optional syntax, displays brief information about the QoS port group map binding for all cards.

1.46.5   Usage Guidelines

Use the show qos port-map binding command to display information about the QoS port group map binding for all the supported cards that are installed on the SmartEdge router. To display information about the QoS port group map binding for a specific card, use the show qos port-map binding slot command.

1.46.6   Examples

The following example shows how to display information about the QoS port group map bindings for all the cards:

[local]Redback>show qos port-map binding

Slot           Card Type         Status      Map Type    Map Name

   4  Current  ge4-20-port       locked      default     tm_max_perf

   6  Current  ge-10-port        unlocked    predef      fwd_max_perf

  10  Current  fege-60-2-port    unlocked    predef      tm_max_perf

The following example shows how to display information about the QoS port group map bindings for the card in slot 6:

[local]Redback>show qos port-map binding slot 6

Slot          Card Type          Status    Map Type  Map Name

   6 Current  ge-10-port         unlocked  predef    fwd_max_perf

The following example shows how to display detailed information about the QoS port group map bindings for the card in slot 6 :

[local]Redback>show qos port-map binding 6 detail

Slot                : 6

Current Card Type   : ge-10-port (0x7b)

Name        : fwd_max_perf

Type        : predef

Description : Predefined map optimized for forwarding performance

Locked      : No


Port : 0123456789

Group: 1122334455

Pending Card Type   : ge-10-port (0x7b)

Name        : fwd_max_perf

Type        : predef

Description : Predefined map optimized for forwarding performance

1.47   show qos queue-map

show qos queue-map [map-name]

1.47.1   Purpose

Displays information about one or more configured quality of service (QoS) queue maps.

1.47.2   Command Mode

all modes

1.47.3   Syntax Description

map-name

Optional. Name of a specific QoS queue map.

1.47.4   Default

When entered without any optional syntax, the show qos queue-map command displays information about all QoS queue maps.

1.47.5   Usage Guidelines

Use the show qos queue-map command to display information about one or more configured QoS queue maps.

Use the map-name argument to display information about a single QoS queue map.

Note:  
By default, most show commands (in any mode) display information for the current context only or, depending on the command syntax, for all contexts. If you are an administrator for the local context, you can insert the optional context ctx-name construct, preceding the show command, to view output for the specified context without entering that context. For more information about using the context ctx-name construct, see the context command description.

Note:  
By appending a space followed by the pipe ( | ) character at the end of a show command, you can filter the output using a set of modifier keywords and arguments. For more information, see “Modifying Output of show Commands” in Using the CLI.

1.47.6   Examples

The following example indicates that the QoS queue map default has 2-queue, 4-queue, and 8-queue mappings:

[local]Redback>show qos queue-map



Queue Map-Name          Grid  Q-2  Q-4  Q-8

default                 1     y    y    y



Total QoS queue map: 1

The following example indicates that:

If a QoS policy with 2 queues is configured with the QoS queue map, default, the highest priority traffic (priority 0) is mapped to queue 0, while all other priorities (1 to 7) are mapped to queue 1.

If a QoS policy with 4 queues is configured with the QoS queue map, default, priority 0 traffic is mapped to queue 0, priority 1 and 2 traffic is mapped to queue 1, priorities 2 to 6 are mapped to queue 2, and the lowest priority traffic (priority 7) is mapped to queue 3.

If a QoS policy with 8 queues is configured with the QoS queue map, default, priority 0 traffic is mapped to queue 0, priority 1 traffic is mapped to queue 1, priority 2 traffic is mapped to queue 2, priority 3 traffic is mapped to queue 3, priority 4 traffic is mapped to queue 4, priority 5 traffic is mapped to queue 5, priority 6 traffic is mapped to queue 6, and priority 7 traffic is mapped to queue 7.

[local]Redback>show qos queue-map default



Queue Map-Name          Grid  Q-2  Q-4  Q-8

default                 1     y    y    y



Queuing Priority   Q-2  Q-4  Q-8



0                  0    0    0

1                  1    1    1

2                  1    1    2

3                  1    2    3

4                  1    2    4

5                  1    2    5

6                  1    2    6

7                  1    3    7



Total QoS queue map: 1

1.48   show qos username

show qos username subscriber [detail]

1.48.1   Purpose

Displays the quality of service (QoS) circuit information for a given subscriber on the system.

1.48.2   Command Mode

all modes

1.48.3   Syntax Description

subscriber

Fully qualified subscriber name, in the format sub-name@ctx-name, for which circuit information is displayed.

detail

Optional. Displays details for each subscriber.

1.48.4   Default

When entered without any optional syntax, displays brief QoS information about the subscriber.

1.48.5   Usage Guidelines

Use the show qos username command to display the QoS circuit information for a given subscriber on the system.

Note:  
By appending a space followed by the pipe ( | ) character at the end of a show command, you can filter the output using a set of modifier keywords and arguments. For more information, see “Modifying Output of show Commands” in Using the CLI.

1.48.6   Examples

The following example shows username and subscriber information:

[local]Redback>show qos username dot-v2.2@local

Circuit                   Policy Name         Type     Rate       Source      

5/2 vlan-id 2 pppoe 1018  gold                pwfq     20000      local       

                          meter3              metering 10000      local       

The following example shows details about a specific user:

[local]Redback#show qos username dot-v2.2@local detail

Circuit: 5/2 vlan-id 2 pppoe 1018

----------------------------------------------------------

Policy Name       : gold              

Policy Type       : pwfq              

Queue position    : 13                Num Queues        : 4                 

Rate              : 20000             Rate Source       : local             

Policy Name       : meter3            

Policy Type       : metering          

Rate              : 10000             Rate Source       : local             

Burst             : 20000             Excess Burst      : 30000