![]() |
COMMAND DESCRIPTION 24/190 82-CRA 119 1170/1-V1 Uen A | ![]() |
Copyright
© Copyright Ericsson AB 2009. All rights reserved.
Disclaimer
No part of this document may be reproduced in any form without the written permission of the copyright owner. The contents of this document are subject to revision without notice due to continued progress in methodology, design and manufacturing. Ericsson shall have no liability for any error or damage of any kind resulting from the use of this document.
Trademark List
SmartEdge | is a registered trademark of Telefonaktiebolaget L M Ericsson. | |
NetOp | is a trademark of Telefonaktiebolaget L M Ericsson. |
Commands starting with “show r” through commands starting with “show z” are included.
show radius control
Displays Remote Authentication Dial-In User Service (RADIUS) server control information.
all modes
This command has no keywords or arguments.
None
Use the show radius control command to display RADIUS server control information.
Table 1 describes the information displayed in the output of the show radius control command. The display represents a snapshot of the current status of the message processing being handled by the RADIUS server or servers.
Field |
Description |
---|---|
Number of servers |
Total number of RADIUS servers in the context or contexts |
Total slots |
Total number of possible outstanding requests for all servers in the context or contexts |
Total in waiting queue |
Number of requests waiting to be processed for all servers in the context or contexts |
Total in process queue |
Number of requests currently being processed for all servers in the context or contexts |
Server status |
Full = no more requests can be handled OK = not full |
The following example displays output from the show radius control command:
[local]Redback>show radius control ========================================================= Context Name: local --------------------------------------------------------- Authentication Accounting Number of server: 3 3 Total slots: 256 256 Total in waiting queue: 1416 0 Total in process queue: 200 0 Server status: OK Ok
show radius counters
Displays counters for Remote Authentication Dial-In User Service (RADIUS) access, accounting, and Change of Authorization (CoA) messages.
all modes
This command has no keywords or arguments.
None
Use the show radius counters command to display RADIUS access and accounting message counters. If the RADIUS server is configured as a CoA server, this command also displays CoA server counters.
Table 2 describes the counters that are displayed in the output of the show radius counters command.
Field |
Description |
---|---|
Access Messages | |
Requests sent |
Number of access request messages sent |
Requests retried |
Number of access request retry messages sent |
Requests send fail |
Number of access request messages that were sent and failed |
Requests timeout |
Number of access request messages that timed out |
Responses drop |
Number of access request messages that were dropped |
Accepts received |
Number of access accept messages received |
Rejects received |
Number of access reject messages received |
Accounting Messages | |
Requests sent |
Number of accounting request messages sent |
Requests retry |
Number of accounting request retry messages sent |
Requests send fail |
Number of accounting request messages that were sent and failed |
Requests timeout |
Number of accounting request messages that timed out |
Responses drop |
Number of accounting request messages that were dropped |
Responses received |
Number of accounting request message responses received |
CoA Messages | |
Requests received |
Number of CoA and disconnect request messages received |
Duplicate request |
Number of duplicate CoA and disconnect request messages received |
Response ACK |
Number of CoA and disconnect requests that were successful |
Response NAK |
Number of CoA and disconnect requests that were unsuccessful |
The following example displays output from the show radius counters command:
[local]Redback>show radius counters ============================================================================= Server: 10.13.130.75 Port: 1812 Counter start time: May 23 17:55:30 2006 ----------------------------------------------------------------------------- Access Messages: ----------------------------------------------------------------------------- Requests sent: 0 Requests retried: 0 Requests send fail: 0 Requests timeout: 0 Responses dropped: 0 Accepts received: 0 Rejects received: 0 ============================================================================= Server: 10.13.130.75 Port: 1813 Counter start time: May 22 23:41:09 2006 ----------------------------------------------------------------------------- Accounting Messages: ----------------------------------------------------------------------------- Requests sent: 356 Requests retried: 1 Requests send fail: 0 Requests timeout: 0 Responses dropped: 0 Accepts received: 357 Rejects received: 0 ============================================================================= Server: 10.13.130.75 Port: 3799 Counter start time: May 22 23:52:35 2006 ----------------------------------------------------------------------------- CoA Messages: ----------------------------------------------------------------------------- Requests received: 12 Duplicate request: 0 Response ACK: 6 Response NAK: 6
show radius server
Displays Remote Authentication Dial-In User Service (RADIUS) server configuration and status information.
all modes
This command has no keywords or arguments.
None
Use the show radius server command to display RADIUS server configuration and status information. If the RADIUS server is configured as a Change of Authorization (CoA) server, this command also displays CoA server information.
The following example displays RADIUS server configuration information and status:
[local]Redback>show radius server
Accounting Server ============================================================================== Address Port Key State State set time ============================================================================== 10.20.1.1 1813 ******** Alive Thu May 11 17:26:05 2006 Algorithm: first Timeout (in sec.): 10 Max retry: 3 Max outstanding: 256 Server timeout (in sec.): 60 Deadtime (in min.): 5 CoA Server ============================================================================== Address Port Key State State set time ============================================================================== 10.20.1.1 3000 ******** Alive Thu May 11 17:31:15 2006
show radius statistics
Displays Remote Authentication Dial-In User Service (RADIUS) server statistics.
all modes
This command has no keywords or arguments.
None
Use the show radius statistics command to display RADIUS server statistics.
Table 3 describes the counters that are displayed in the output of the show radius statistics command.
Field |
Description |
---|---|
Authentication Servers |
|
Requests send |
Number of access request messages sent. |
Requests re-send |
Number of access-requests sent more than one time by the
SmartEdge® router to the RADIUS servers (NetOp |
Requests timeout |
Number of access request messages that timed out |
Requests send fail |
Number of access request messages that were sent and failed |
Requests accepted |
Number of access-accepts received by the SmartEdge router from the RADIUS servers (NetOp PM) |
Requests rejected |
Number of access-rejects received by the SmartEdge router from the RADIUS servers (NetOp PM) |
Response dropped |
Number of access request messages that were dropped |
Req in process |
Total number of access-requests outstanding from the SmartEdge router. |
Req in waiting |
Number of subscribers waiting for an available slot to send the access-request to the RADIUS servers. |
Req in high wait queue |
|
Req in low wait queue |
|
Server slots |
Total number of simultaneous access-requests that can out stand from the SmartEdge router. |
Capacity |
Percentage of server slots currently in use. |
Server marked dead |
Number of RADIUS servers known as dead at the moment the show command was typed. |
Accounting Servers |
|
Requests send |
Number of access request messages sent. |
Requests re-send |
Number of access-requests sent more than one time by the SmartEdge router to the RADIUS servers (NetOp PM) because the timeout set (command radius timeout) in the configuration is over |
Requests timeout |
Number of access request messages that timed out |
Requests send fail |
Number of access request messages that were sent and failed |
Requests accepted |
Number of access-accepts received by the SmartEdge router from the RADIUS servers (NetOp PM) |
Requests rejected |
Number of access-rejects received by the SmartEdge router from the RADIUS servers (NetOp PM) |
Response dropped |
Number of access request messages that were dropped |
Req in process |
Total number of access-requests outstanding from the SmartEdge router. |
Req in waiting |
Number of subscribers waiting for an available slot to send the access-request to the RADIUS servers. |
Req in high wait queue |
|
Req in low wait queue |
|
Server slots |
Total number of simultaneous access-requests that can out stand from the SmartEdge router. |
Capacity |
Percentage of server slots currently in use. |
Server marked dead |
Number of RADIUS servers known as dead at the moment the show command was typed. |
CoA Servers |
|
Requests received |
|
Duplicate requests |
|
Response ACK |
|
Response NAK |
|
Send details |
|
— |
— |
Subscriber authentication |
|
Request send |
|
Request retransmit |
|
Response received |
|
Server busy |
|
Server not ready |
|
No server |
|
Server marked dead |
|
Bad attribute |
|
Socket error |
|
Send accept to AAAd |
|
Send reject to AAAd |
|
Send meth fail to AAAd |
|
Internal error |
|
Unknown attribute |
|
Authorization |
|
Request send |
|
Request retransmit |
|
Response received |
|
Server busy |
|
Server not ready |
|
No server |
|
Server marked dead |
|
Bad attribute |
|
Socket error |
|
Send accept to AAAd |
|
Send reject to AAAd |
|
Send meth fail to AAAd |
|
Internal error |
|
Unknown attribute |
|
Subscriber accounting |
|
Request send |
|
Request retransmit |
|
Response received |
|
Server busy |
|
Server not ready |
|
No server |
|
Server marked dead |
|
Bad attribute |
|
Socket error |
|
Accounting accepted |
|
Accounting timeout |
|
Internal error |
|
Unknown attribute |
|
L2tp accounting |
|
Request send |
|
Request retransmit |
|
Response received |
|
Server busy |
|
Server not ready |
|
No server |
|
Server marked dead |
|
Bad attribute |
|
Socket error |
|
Accounting accepted |
|
Accounting timeout |
|
Internal error |
|
Unknown attribute |
|
Accounting On/Off |
|
Request send |
|
Request retransmit |
|
Response received |
|
Server busy |
|
Server not ready |
|
No server |
|
Server marked dead |
|
Bad attribute |
|
Socket error |
|
Accounting accepted |
|
Accounting timeout |
|
Internal error |
|
Unknown attribute |
|
Event accounting |
|
Request send |
|
Request retransmit |
|
Response received |
|
Server busy |
|
Server not ready |
|
No server |
|
Server marked dead |
|
Bad attribute |
|
Socket error |
|
Accounting accepted |
|
Accounting timeout |
|
Internal error |
|
Unknown attribute |
|
Receive Details |
|
No match request |
|
No match server |
|
Invalid packet |
|
Bogus packet |
|
Dup response packet |
|
The following example displays RADIUS statistics:
[local]Redback>show radius statistics Context: local Authentication Servers: Requests send: 0 Requests re-send: 0 Request timeout: 0 Requests send fail: 0 Requests accepted: 0 Requests rejected: 0 Requests timeout: 0 Response dropped: 0 Req in process: 0 Req in waiting: 0 Req in high wait queue: 0 Req in low wait queue: 0 Server slots 0 Capacity: 0% Server marked dead: 0 Accounting Servers: Requests send: 2 Requests re-send: 1 Request timeout: 0 Requests send fail: 1 Requests accepted: 2 Requests rejected: 0 Requests timeout: 0 Response dropped: 0 Req in process: 0 Req in waiting: 0 Req in high wait queue: 0 Req in low wait queue: 0 Server slots: 256 Capacity: 0% Server marked dead: 0 Send Details: Subscriber authentication: Request send: 0 Request retransmit: 0 Response received: 0 Server busy: 0 Server not ready: 0 No server: 0 Server marked dead: 0 Bad attribute: 0 Socket error: 0 Send accept to AAAd: 0 Send reject to AAAd: 0 Send meth fail to AAAd: 0 Internal error: 0 Authorization: Request send: 0 Request retransmit: 0 Response received: 0 Server busy: 0 Server not ready: 0 No server: 0 Server marked dead: 0 Bad attribute: 0 Socket error: 0 Send accept to AAAd: 0 Send reject to AAAd: 0 Send meth fail to AAAd: 0 Internal error: 0 Subscriber session accounting: Request send: 2 Request retransmit: 1 Response received: 2 Server busy: 0 Server not ready: 0 No server: 0 Server marked dead: 0 Bad attribute: 0 Socket error: 0 Send accept to AAAd: 1 Send reject to AAAd: 0 Send meth fail to AAAd: 0 Internal error: 0 L2tp accounting: Request send: 0 Request retransmit: 0 Response received: 0 Server busy: 0 Server not ready: 0 No server: 0 Server marked dead: 0 Bad attribute: 0 Socket error: 0 Send accept to AAAd: 0 Send reject to AAAd: 0 Send meth fail to AAAd: 0 Internal error: 0 Accounting On/Off: Request send: 0 Request retransmit: 0 Response received: 0 Server busy: 0 Server not ready: 0 No server: 0 Server marked dead: 0 Bad attribute: 0 Socket error: 0 Send meth fail to AAAd: 0 Internal error: 0 Event accounting: Request send: 0 Request retransmit: 0 Response received: 0 Server busy: 0 Server not ready: 0 No server: 0 Server marked dead: 0 Bad attribute: 0 Socket error: 0 Send accept to AAAd: 0 Send reject to AAAd: 0 Send meth fail to AAAd: 0 Internal error: 0 Receive Details: No match request: 0 No match server: 0 Invalid packet: 0 Bogus packet: 0
show rate-limit card {all | slot} dhcp {counter | log}
Displays dropped Dynamic Host Configuration Protocol (DHCP) packet information for one or more traffic cards.
all modes
all |
Displays DHCP packet information for all traffic cards. |
slot |
Slot number of a specific traffic card. |
counter |
Displays the count of dropped DHCP packets for one or all traffic cards. |
log |
Displays the log messages for dropped DHCP packets for one or all traffic cards. |
None
Use the show rate-limit card command to display DHCP packet information for packets dropped because of rate limiting.
Use the counter keyword to display the count of dropped DHCP packets for one or all traffic cards.
Use the log keyword to display the log messages for dropped DHCP packets for one or all traffic cards.
The following example displays the count of dropped DHCP packets for the traffic card in slot 1:
[local]Redback>show rate-limit card 1 dhcp counter Slot 1 Ingress: card rate-limit 1060236 packets
The following example displays the log messages for the traffic card in slot 1:
[local]Redback>show rate-limit card 1 dhcp log Slot 1 Ingress: current index: 103 000 src-ip-addr 2.1.1.2 src-mac-addr 00 00 03 00 03 00 circuit 1/3:1023:63/1/1/5 001 src-ip-addr 2.1.1.2 src-mac-addr 00 00 03 00 03 00 circuit 1/3:1023:63/1/1/5 002 src-ip-addr 2.1.1.2 src-mac-addr 00 00 03 00 03 00 circuit 1/3:1023:63/1/1/5 003 src-ip-addr 2.1.1.2 src-mac-addr 00 00 03 00 03 00 circuit 1/3:1023:63/1/1/5 004 src-ip-addr 2.1.1.2 src-mac-addr 00 00 03 00 03 00 circuit 1/3:1023:63/1/1/5 005 src-ip-addr 2.1.1.2 src-mac-addr 00 00 03 00 03 00 circuit 1/3:1023:63/1/1/5
show rcm {memory | session}
Displays Router Configuration Manager (RCM) information.
all configuration modes
memory |
Displays RCM memory usage. |
session |
Displays RCM session information. |
None
Use the show rcm command to display RCM information.
The following example displays output from the show rcm command with the memory keyword:
[local]Redback>show rcm memory
Displaying memory usage by RCM: Internal chunk memory : 125200 bytes Dynamically memory allocated by all : 13844 bytes Memory allocated for msg by RCM components : 0 bytes
The following example displays output from the show rcm command with the session keyword:
[local]Redback>show rcm session
CLI pid State Trans ID Waiting on ------------------------------------------------------------------- 13117 Not in transaction N/A None 13059 Not in transaction N/A None 12610 In transaction 3062 None
show redundancy
Displays the state of the standby controller card and verifies whether it is ready to become active.
This command has no keywords or arguments.
None
Use the show redundancy command to display the state of the standby controller card and to verify whether it is ready to become active.
The following example displays the state of the controller cards:
[local]Redback>show redundancy
--------------------------------- This XCRP is active --------------------------------- Firmware in sync? : YES Software Release in sync? : YES Database in sync? : YES Mate-to-Mate link up? : YES Standby Ready? : YES
show release
Displays release and installation information for the software images currently installed on the system.
This command has no keywords or arguments.
None
Use the show release command to display the release and installation information for the software images on the system and the partitions in which they are installed. The active image shows the software that is currently loaded in the system, and the alternate image shows the alternate image available on the system.
The following example displays the release and installation information for the installed software images:
[local]Redback>show release
Installed releases: p02: active (will be booted after next reload) ---------------------------------------------- Version SEOS-5.0.5-Release Built on Mon Jan 02 10:00:01 PST 2006 Copyright (C) 1998-2006, Redback Networks Inc. All rights reserved. p01: alternate -------------- Version SEOS-5.0.5-Release Built on Mon Jan 16 10:00:01 PDT 2006 Copyright (C) 1998-2006, Redback Networks Inc. All rights reserved.
show rip debug
Displays enabled Routing Information Protocol (RIP) debug settings.
all modes
This command has no keywords or arguments.
None
Use the show rip debug command to display enabled RIP debug settings.
The following example displays output from the show rip debug command:
[local]Redback>show rip debug
RIP debug flags: REQUEST_RECV REQUEST_SEND RESPONSE_RECV RESPONSE_SEND PACKET_GENERAL RIP debug detail flags:
Displays information for all Routing Information Protocol (RIP) instances, or only for a particular RIP instance.
all modes
instance |
Optional. RIP instance name. |
When entered without the optional instance argument, this command displays information for all configured RIP instances.
Use the show rip instance command to display information for all RIP instances, or only for a particular RIP instance.
The following example displays output from the show rip instance command:
[local]Redback>show rip instance
Fl - Instance Flags: (O - Default information originate), P - Maximum paths TH - Flash update threshold, DM - Default metric, Dis - Admin distance Dl - Output delay, TableVer - Routing table version, Upd - Update Inv - Invalid, Hld - Holddown, Flu - Flush, Expr - Next flashupdate GblFlg - Global flags: (I - ISM up, P - RPM up, R-RIB up) InstanceName Fl P TH DM Dis Dl TableVer Expr Upd/Inv/Hld/Flu GblFlg area1 - 8 5 0 120 0 1 2 30 180 180 240 IPR area2 - 8 5 0 120 0 1 2 30 180 180 240 IPR
Displays information for all Routing Information Protocol (RIP) interfaces, or only for RIP interfaces within a particular RIP instance.
all modes
instance |
Optional. RIP instance name. |
When entered without the optional instance argument, this command displays information about all RIP interfaces.
Use the show rip interface to display information for all RIP interfaces, or only for RIP interfaces within a particular RIP instance.
The following example displays output from the show rip interface command:
[local]Redback>show rip interface
Interface Flags: U - Up, B - Bound, L - Listen, S - Supply, A-Admin up V - have Valid addr, R-Registered with ISM, O - Default information originate N - No default info orig, H - split Horizon, P - Poison reverse, Upd - Update Inv - Invalid, Hld - Holddown, FLu - Flush, Expr - Next full update, Co - Cost Interfaces of RIP instance: area1 Name Addr/MaskLen State Upd/Inv/Hld/Flu Expr Co IntfId ripint1 10.1.1.1/24 LSRVH 30 180 180 240 29 1 10000001 Total 1 interfaces, 0 are up.
show ripng {all-instances | debug | instance [instance-id] | interface [if-name] | route [instance-id]}
Displays Routing Information Protocol next generation (RIPng) information.
all modes
all-instances |
Displays information for all RIPng instances. |
debug |
Displays RIPng debug settings. |
instance |
Displays RIPng instance information. |
instance-id |
Optional. Instance ID. When specified, displays RIPng instance or RIPng route information for a specific RIPng instance. |
interface |
Displays RIPng interface information. |
if-name |
Optional. Interface name. When specified, displays information for a specific RIPng interface. |
route |
Displays RIPng route information. |
None
Use the show ripng command to display RIPng information.
The following example displays information for all RIPng instances:
[local]Redback>show ripng all-instances Fl - Flags: (O - Default information originate, M - Maximum routes reached) P - Maximum paths TH - Flash update threshold, DM - Default metric, Dis - Admin distance Dl - Output delay, TableVer - Routing table version, Upd - Update Inv - Invalid, Hld - Holddown, Flu - Flush, Expr - Next flashupdate InstanceName Fl P TH DM Dis Dl TableVer Expr Upd/Inv/Hld/Flu #Route Context local: 1 - 16 5 0 120 0 4 1 30 180 180 240 3
The following example displays the RIPng debug settings:
[local]Redback>show ripng debug RIP debug flags: REQUEST_RECV REQUEST_SEND RESPONSE_RECV RESPONSE_SEND PACKET_GE NERAL MEMORY INTERNAL PROTOCOL IPC TIMER INTERFACE LOCAL_RIB GLOBAL_RIB POLICY C ONFIG IN_QUEUE OUT_QUEUE AUTHENTICATION THREAD SOCKIO ISM GENERAL RIP debug detail flags:
The following example displays information for the RIPng instance, 4:
[local]Redback>show ripng instance 4 Fl - Flags: (O - Default information originate, M - Maximum routes reached) P - Maximum paths TH - Flash update threshold, DM - Default metric, Dis - Admin distance Dl - Output delay, TableVer - Routing table version, Upd - Update Inv - Invalid, Hld - Holddown, Flu - Flush, Expr - Next flashupdate InstanceName Fl P TH DM Dis Dl TableVer Expr Upd/Inv/Hld/Flu #Route Context local: 1 - 16 5 0 120 0 4 3 30 180 180 240 3
The following example displays information for the RIPng interface, 88:
[local]Redback>show ripng interface 88 Interface Flags: U - Up, B - Bound, L - Listen, S - Supply, A-Admin up V - have Valid addr, R-Registered with ISM, O - Default information originate N - No default info orig, H - split Horizon, P - Poison reverse, Upd - Update Inv - Invalid, Hld - Holddown, FLu - Flush, Expr - Next full update, Co - Cost Interfaces of RIP instance: 1 Name Addr/MaskLen State Upd/Inv/Hld/Flu Expr Co IntfId lo 8001::1/128 ULVH 30 180 180 240 16 1 10000004 to-nbor 7001::1/112 ULSVH 30 180 180 240 16 1 10000003 Total 2 interfaces, 2 are up.
The following example displays information for the RIPng route, 37:
[local]Redback>show ripng route 37 T - RouteType:(C - Connected, E - External, R - RIP, EB - External backup) M - Metric, Exp - Expire time, PrFl - Prefix flags ( D - Delete, H - Holddown A - Need flash, B - Need download to RIB, I - Inactive) NhFl - Next Hop Flags (W - Withdrawn from RIB, H - Holddown, F - Flush expire before holddown) Routing table for RIP instance: 1 T Prefix/PrefixLen NextHop M Exp PrFl|NhFl Intf Peer C 7001::/112 :: 0 - 6|6 to-nbor C 8001::1/128 :: 0 - 6|6 lo R 8001::2/128 fe80::230:88ff:fe00:3294 1 172 6|6 to-nbor Total 3 prefixes 3 routes(1 intern 0 extern 2 connected)
Displays information about all Routing Information Protocol (RIP) routes, or only for routes within a particular RIP instance.
all modes
instance |
Optional. RIP instance name. |
ip-addr/prefix-length |
Optional. IP address (in the form A.B.C.D) and prefix length, separated by the slash (/) character. The range of values for the prefix-length argument is 0 to 32. |
longer-prefixes |
Optional. Displays all routes that fall into the range of the prefix; otherwise, only routes that exactly match are displayed. |
When entered without any optional arguments, this command displays information about all RIP routes.
Use the show rip route command to display information about RIP routes, or only for routes within a particular RIP instance.
The following example displays output from the show rip route command:
[local]Redback>show rip route
T - RouteType: (C - Connected, E - External, R - RIP, EB - External backup) M - Metric, Exp - Expire time, PrFl - Prefix flags D - Delete, H - Holddown A - Need flash, B - Need download to RIB, I - Inactive) NhFl - Next Hop Flags (W - Withdrawn from RIB, H - Holddown, F - Flush expire before holddown) Routing table for RIP instance: rip001 T Prefix NextHop M Exp PrFl|NhFl Intf Peer Total 0 prefixes 0 routes (0 intern 0 extern 0 connected)
show rmon {alarms | events}
Displays Remote Monitoring (RMON) information.
alarms |
Displays RMON alarm records. |
events |
Displays RMON event records. |
None
Use the show rmon command to display RMON information.
The following example displays RMON alarms:
[local]Redback>show rmon alarm
rmon alarm 5 ipInReceives.0 50 delta rising-threshold 5000 5 falling-threshold 200 6 owner "gold.isp.net" rmon alarm 10 ipForwDatagrams.0 60 delta rising-threshold 3000000 1 falling-threshold 600000 2 rmon alarm 20 rbnCpuMeterOneMinuteAvg.0 5 absolute rising-threshold 50 3 falling-threshold 10 4 owner "alarmDel6"
The following example displays RMON events:
[local]Redback>show rmon events
rmon event 1 log notify owner gold.isp.net description "packets per second too high in context gold.isp.net" rmon event 2 log notify owner gold.isp.net description "packets per second is below 10000 in context gold.isp.net" rmon event 3 log notify owner gold.isp.net description "One minute average CPU usage on the device is above 50%" rmon event 4 log notify owner gold.isp.net description "One minute average CPU usage on the device is now below 10%" rmon event 5 log notify owner gold.isp.net description "The total number of input IP datagrams received from interfaces per second is 100 and above" rmon event 6 log notify owner gold.isp.net description "The total number of input IP datagrams received from interfaces per second is 4 and below"
show route-map [map-name] [summary]
Displays information about configured route maps.
all modes
map-name |
Optional. Name of the route map. |
summary |
Optional. Displays route map summary information. |
Displays all configured route maps.
Use the show route-map command to display information about configured route maps.
The following example displays all configured route maps:
[local]Redback>show route-map
route-map c1-a2-in: count: 6, sequences: 10 - 40, client count: 1 modified: 2 day(s), 21 hour(s) ago sequence 10, permit (hits: 13, cache hits: 7) Match clauses: as-path (as-path filter): AS2686 Set clauses: local-preference 80 weight 65535 sequence 15, permit (hits: 17667, cache hits: 17667) Match clauses: ip address (prefix list): /22-permit Set clauses: community local-AS sequence 20, permit (hits: 2, cache hits: 0) Match clauses: ip address (prefix list): slash9 Set clauses: metric 80 sequence 25, permit (hits: 3, cache hits: 0) Match clauses: ip address (prefix list): slash18 Set clauses: community-list no-export/11:121-delete delete community 11:102 additive ip next-hop 10.255.255.254 sequence 30, permit (hits: 307062, cache hits: 0) Match clauses: community (community list filter): 11:121-c1-wtn Set clauses: community 11:102 additive sequence 40, permit (hits: 0, cache hits: 0) Match clauses: Set clauses: route-map a2-out-map: count: 4, sequences: 10 - 40, client count: 1 modified: 2 day(s), 21 hour(s) ago sequence 40, permit (hits: 2227, cache hits: 0) Match clauses: community (community list filter): a2community Set clauses: metric-type internal total route maps: 2
The following command displays a summary of all configured route maps:
[local]Redback>show route-map summary
route-map c1-a2-in: count: 6, sequences: 10 - 40, client count: 1 modified: 2 day(s), 21 hour(s) ago route-map a2-out-map: count: 4, sequences: 10 - 40, client count: 1 modified: 2 day(s), 21 hour(s) ago total route maps: 2
show rsvp counters [global | lsp | packets]
Displays Resource Reservation Protocol (RSVP) counter information.
global |
Optional. Displays only global counters. |
lsp |
Optional. Displays only label-switched path (LSP)-related counters. |
packets |
Optional. Displays only packet-related counters. |
Displays all RSVP counter information.
Use the show rsvp counters command to display RSVP counter information.
The following example displays packet-related output from the show rsvp counters command:
[local]Redback>show rsvp counters packets
--- Global RSVP Counters --- Packet Counters Interval: 00:00:09 Packets Sent: 0 Packets Recvd: 0 Packets Tx dropped: 0 Packets Rx dropped: 0 Packets Tx IO errs: 0 Packets Rx IO errs: 0 PATH Sent: 0 PATH Recvd: 0 RESV Sent: 0 RESV Recvd: 0 PATH TEAR Sent: 0 PATH TEAR Recvd: 0 RESV TEAR Sent: 0 RESV TEAR Recvd: 0 PATH ERR Sent: 0 PATH ERR Recvd: 0 RESV ERR Sent: 0 RESV ERR Recvd: 0 CONFIRM Sent: 0 CONFIRM Recvd: 0 Unknown Pkts Recvd: 0
The following example displays LSP-related output from the show rsvp counters command:
[local]Redback>show rsvp counters lsp
--- Global RSVP Counters --- LSP Counters Total Sessions: 26 Total LSPs: 27 Ingress LSPs: 7 Egress LSPs: 18 Transit LSPs: 2 Backup LSPs: 1 Up LSPs: 23 Down LSPs: 4 Active LSPs: 23 Backup2 LSPs: 0 Bypass LSPs: 0 Rerouted LSPs: 0 Stale LSPs: 5 Stale LSPs Recovered: 5
In this example:
Stale LSPs = The number of LSPs that moved to the Stale state due to local or neighbor restart events.
Stale LSPs Recovered = The number of previously stale LSPs that moved back successfully to the Up state.
show rsvp debug
Displays Resource Reservation Protocol (RSVP) debug information.
all modes
This command has no keywords or arguments.
None
Use the show rsvp debug command to display RSVP debug information.
The following example displays output from the show rsvp debug command:
[local]Redback>show rsvp debug
Event Filter Packet Packet Send Path Send Path Recv Resv Send Resv Recv Path Error Send Path Error Recv Resv Error Send Resv Error Recv Path Tear Send Path Tear Recv Packet Confirm Send Packet Confirm Recv Packet Recv
show rsvp explicit-route [er-name] [detail]
Displays explicit route information.
all modes
er-name |
Optional. Name of the explicit route for which information is displayed. |
detail |
Optional. Displays detailed information for the specified explicit route or all explicit routes. |
Displays summary information for all explicit routes.
Use the show rsvp explicit-route command to display explicit route information.
Use the er-name argument to display detailed information for a specific explicit route.
Use the detail keyword to display the detailed explicit route information; otherwise, the summary information is displayed.
The following example displays summary information for all explicit routes:
[local]Redback>show rsvp explicit-route Explicit Route Hop Count exp-rt1 2
The following example displays detailed information for the exp-rt1 explicit route:
[local]Redback>show rsvp explicit-route exp-rt1 Explicit Route: exp-rt1 Hop Count: 2 Length: 8 Addr: 10.1.1.1/32 Length: 8 Addr: 10.2.1.2/32
show rsvp interface [if-name | detail]
Displays Resource Reservation Protocol (RSVP) interface summary information.
all modes
if-name |
Optional. Name of the RSVP interface to be displayed. |
detail |
Optional. Displays detailed information. |
Displays all RSVP interface summary information.
Use the show rsvp interface command to display all RSVP interface summary information.
Use the if-name argument to display information for only a specific RSVP interface.
Use the detail keyword to display detailed RSVP interface information; otherwise, summary information is displayed.
The following example shows how to display information for all configured RSVP interfaces:
[local]Redback>show rsvp interface
--- All RSVP Interfaces --- Address/Mask Name State Bound to 1.1.1.1/24 one Up 7/4 3.1.1.1/24 two Up 7/2
The following example shows how to display information for the IPst.14 RSVP interface :
[local]router#show rsvp interface IPst.14 --- RSVP Interface 10.18.241.74 --- Name : IPst.14 Mask : 255.255.255.252 State : Down Bound to : Refresh Interval (sec) : 30 Keep Multiplier : 6 Hello Interval (sec) : 0 Hello Keep Multiplier : 3 Max Bandwidth (By/sec) : 0 TE metric : Use IGP metric TE update threshold : 5 TE advertisements : 0 Tracking : Enabled (tracking objects below) Track-mtu Allocated BW (By/sec) : 0 Priority Resv B/W (By/sec) Last-Advertised Available 0 0 0 0 1 0 0 0 2 0 0 0 3 0 0 0 4 0 0 0 5 0 0 0 6 0 0 0 7 0 0 0
show rsvp lsp [up | down | label | protection | backup | bypass | protected | ingress | egress | transit | track ] [detail ] | lsp-name]
Displays Resource Reservation Protocol (RSVP) label-switched path (LSP) information.
all modes
up |
Optional. Displays only up LSPs. |
down |
Optional. Displays only down LSPs. |
label |
Optional. Displays label information for RSVP LSPs. |
protection |
Optional. Displays only protection information. |
backup |
Optional. Displays only back-up LSPs. |
bypass |
Optional. Displays only bypass LSPs. |
protected |
Optional. Displays only protected LSPs with back-ups configured. |
ingress |
Optional. Displays only ingress LSPs. |
egress |
Optional. Displays only egress LSPs. |
transit |
Optional. Displays only transit LSPs. |
track |
Optional. Displays information about the tracking-enabled label-switched paths (LSPs) that are currently configured on your system. Include the lsp-name argument after the track keyword to display tracking information for a specific LSP. Include the detail keyword after the track keyword to display detailed tracking information for a specific LSP. |
detail |
Optional. Displays detailed information. |
lsp-name |
Optional. Name of LSP for which information is displayed. |
Displays summary information for all LSPs.
Use the show rsvp lsp command to display all RSVP LSP information.
Use the lsp-name argument to display information only for the specified LSP, or use any of the available keywords to display LSP information only for the specified keyword.
The following example displays information for all RSVP LSPs:
[local]Redback>show rsvp lsp
RSVP LSPs LSP ID Ingress Endpoint State FRR Origin Protection W-E-bkup 1 10.1.1.2 10.2.1.2 Up Ingress Backup W-E-lsp 1 10.1.1.2 10.2.1.2 Shut Ingress Primary E-W-lsp 2 10.2.1.2 10.1.1.2 Up Egress None
The show rsvp lsp command displays the following:
LSP = Name of the LSP. Each RSVP LSP has a specific name.
ID = Tunnel ID of the LSP (this ID is determined by the ingress node of the LSP).
Ingress = IP address of the ingress of the LSP. Usually, this address is the IP address of the router from which the packet got its LSP, but the ingress address is configurable for SE RSVP LSPs; so, it can also be a loopback address.
Endpoint = Destination address of the LSP. Usually, this address is the IP address of the destination router to which the packet has its last hop, but the address does not need to be the router ID of the destination router; it can be a loopback address configured at the destination router.
State = State of the LSP. The state can be Up, Down, Shut, or Stale.
FRR = If the LSP has an FRR bypass LSP that can protect it, then this field displays the tunnel ID of the bypass LSP that is protecting it. Otherwise, this field is empty.
0rigin = Origin, for the type of LSP relative to the location of the local switch in the path: I (or Ingress) for ingress, E (or Egress) for egress, or T (or Transit) for transit.
Protection = Protection characteristic of the LSP. For example, if an LSP does not protect other LSPs but is protected by other LSPs, Prim (for primary LSP) is listed. If an LSP protects other LSPs (a backup or backup of a backup), Back is listed. If an LSP has no protection characteristic, None is listed. If an LSP is a bypass LSP, it is pre-established to protect an LSP that traverses either a specific link (link bypass LSP) or node (node bypass LSP), and Bypas is listed.
The following example displays information for RSVP LSPs that are currently shut down:
[local]Redback>show rsvp lsp down
RSVP LSPs LSP ID Ingress Endpoint State FRR Origin Protection W-E-lsp 1 10.1.1.2 10.2.1.2 Shut Ingress None
The following example displays information for RSVP LSPs that are currently up:
[local]Redback>show rsvp lsp up
RSVP LSPs LSP ID Ingress Endpoint State FRR Origin Protection W-E-bkup 1 10.1.1.2 10.2.1.2 Up Ingress Backup E-W-lsp 2 10.2.1.2 10.1.1.2 Up Egress None
The following example displays information for egress RSVP LSPs:
[local]Redback>show rsvp lsp egress
RSVP LSPs LSP ID Ingress Endpoint State FRR Origin Protection E-W-lsp 2 10.2.1.2 10.1.1.2 Up Egress None
The following example displays information for ingress RSVP LSPs:
[local]Redback>show rsvp lsp ingress LSP TID Ingress Endpoint State FRR O Prtct R1-R5-backup 1 10.2.250.201 10.2.250.205 Up I Back R1-R5-prim 1 10.2.250.201 10.2.250.205 Up 8 I Prim R1-R6-backup 3 10.2.250.201 10.2.250.206 Up I Back R1-R6-prim 3 10.2.250.201 10.2.250.206 Up 7 I Prim R1-R3-bypass 4 10.2.250.201 10.2.250.203 Up I Bypas R1-R2-prim 6 10.2.250.201 10.2.250.202 Up 7 I None R1-R2-bypass 7 10.2.250.201 10.2.250.202 Up I Bypas R1-R5-bypass-node-R3 8 10.2.250.201 10.2.250.205 Up I Bypas R1-R3-prim 9 10.2.250.201 10.2.250.203 Up 4 I None R1-R4-prim 10 10.2.250.201 10.2.250.204 Up 7 I None
This example shows information on incoming packet in the local MPLS-enabled network where RSVP is used to communicate labels and their meaning among label-switched routers (LSRs). At each incoming (ingress) point of the network, packets are assigned a label by an edge label-switched router (LSR). Packets are forwarded along a label-switched path (LSP) where each LSR makes forwarding decisions based on the label information. At each hop, the LSR swaps the existing label for a new label that tells the next hop how to forward the packet. At the outgoing (egress) point, an edge LSR removes the label, and forwards the packet to its destination. The show rsvp lsp ingress command displays the following:
LSP = The name of the LSP. All RSVP LSPs have a specific name.
TID = The Tunnel ID. It is unique per originating node, for a given LSP, so the ID can be 1 to 40,000.
Ingress = The IP address of the ingress of the LSP. Usually, this is the IP address of the router that the packet got its LSP from, but the ingress address is configurable for SE RSVP LSPs, so it can also be a loopback address.
Endpoint = The destination address of the LSP. Usually, this is the IP address of the destination router that the packet has its last hop to, but the address does not need to be the destination router's router ID, it can be a loopback address configured at the destination router.
State = The state of the LSP. The state can be Up, Down, Shut, or Stale.
FRR = If the LSP has a Fast-Reroute (FRR) bypass LSP that can protect it, then this field displays the tunnel ID of the bypass LSP that is protecting it. Otherwise, this field is empty.
0 = Origin, for the type of LSP with regards to where the local switch is in the path: I for ingress, E for egress, or T for transit.
Prtct = The protection characteristic of the LSP. For example, if it is an LSP that does not protect other LSPs but is protected by other LSPs, Prim (for primary LSP) is listed. If it is an LSP that protects other LSPs (a backup or backup of a backup), Back is listed. If it has no protection characteristic, None is listed. If it is a bypass LSP, it is pre-established to protect an LSP that traverses either a specific link (link bypass LSP) or node (node bypass LSP), and Bypas is listed.
The following example displays label information for all RSVP LSPs:
[local]Redback>show rsvp lsp label
LSP State Upstream lbl Downstream lbl W-E-bkup Up N/A 262144 W-E-lsp Shut N/A 0 E-W-lsp Up 3 N/A
The following example displays information for RSVP LSPs protected with a backup LSP:
[local]Redback>show rsvp lsp protected
LSP ID Ingress Endpoint State Backed up by W-E-lsp 1 10.1.1.2 10.2.1.2 Shut W-E-bkup
The following example displays protection information for all RSVP LSPs:
[local]Redback>show rsvp lsp protection
Primary State Active Backup State Active W-E-lsp Shut No W-E-bkup Up Yes
The following example displays information for transmit RSVP LSPs:
[local]Redback>show rsvp lsp transit
RSVP LSPs LSP ID Ingress Endpoint State FRR Origin Protection W-E-bkup 1 10.1.1.2 10.2.1.2 Up Transit None E-W-lsp 2 10.2.1.2 10.1.1.2 Up Transit None
The following example shows how to display summary information about all tracking-enabled LSPs currently configured on the router:
[local]Redback#show rsvp lsp track
LSP TID Ingress Endpoint State FRR O Prtct AC1_MTU1_azul 13 10.18.241.3 10.18.241.6 Down (tracking) I None AC1_AC2_rojo 22 10.18.241.3 10.18.241.4 Down (tracking) I Prim
The following example shows how to display information about the AC1_MTU1_azul tracking-enabled LSP:
[local]Redback#show rsvp lsp track AC1_MTU1_azul --- RSVP LSP AC1_MTU1_azul (Tunnel ID: 13) --- Ingress : 10.18.241.3 Endpoint : 10.18.241.6 Origin : Ingress LSP State : Down (tracking) Extended Tunnel ID : 10.18.241.3 LSP ID : 1 Traffic-Eng : default State Transitions : 2 Downstream Nhop : 0.0.0.0 Downstream Intf : 0.0.0.0 Downstream Intf Name: Downstream Nbr : 0.0.0.0 Downstream Label : 0 Setup Priority : 7 Holding Priority : 0 Last Downstream Tx : 58761 Last Downstream Rx : 0 Next Timer in (sec) : 1271218063 Lifetime (sec) : 0 Time to Die (sec) : 0 B/W (Bytes/sec) : 0 LSP cct : Cct invalid IGP Shortcut : Disabled Session Attr : Local-Protect Node-Protect May-Reroute Record-Label Use CSPF Route : Yes Record Route : Yes Dynamic Route : Tracking : Track-mtu Tracking State : Down CSPF Route : Pending
The following example shows how to display detailed information about all tracking-enabled LSPs currently configured on the router:
[local]Redback#show rsvp lsp track detail --- RSVP LSP AC1_MTU1_azul (Tunnel ID: 13) --- Ingress : 10.18.241.3 Endpoint : 10.18.241.6 Origin : Ingress LSP State : Down (tracking) Extended Tunnel ID : 10.18.241.3 LSP ID : 1 Traffic-Eng : default State Transitions : 2 Downstream Nhop : 0.0.0.0 Downstream Intf : 0.0.0.0 Downstream Intf Name: Downstream Nbr : 0.0.0.0 Downstream Label : 0 Setup Priority : 7 Holding Priority : 0 Last Downstream Tx : 59130 Last Downstream Rx : 0 Next Timer in (sec) : 1271217694 Lifetime (sec) : 0 Time to Die (sec) : 0 B/W (Bytes/sec) : 0 LSP cct : Cct invalid IGP Shortcut : Disabled Session Attr : Local-Protect Node-Protect May-Reroute Record-Label Use CSPF Route : Yes Record Route : Yes Dynamic Route : Tracking : Track-mtu Tracking State : Down CSPF Route : Pending --- RSVP LSP AC1_AC2_rojo (Tunnel ID: 22) --- Ingress : 10.18.241.3 Endpoint : 10.18.241.4 Origin : Ingress LSP State : Down (tracking) Extended Tunnel ID : 10.18.241.3 LSP ID : 1 Traffic-Eng : default State Transitions : 2 Downstream Nhop : 0.0.0.0 Downstream Intf : 0.0.0.0 Downstream Intf Name: Downstream Nbr : 0.0.0.0 Downstream Label : 0 Setup Priority : 7 Holding Priority : 0 Last Downstream Tx : 59764 Last Downstream Rx : 0 Next Timer in (sec) : 1271217694 Lifetime (sec) : 0 Time to Die (sec) : 0 B/W (Bytes/sec) : 0 LSP cct : Cct invalid IGP Shortcut : Disabled Session Attr : Local-Protect Node-Protect May-Reroute Record-Label Use CSPF Route : Yes Record Route : Yes Dynamic Route : LSP protected by LSP AC1_AC2_verde which is protected by LSP AC1_AC2_3camino Tracking : Track-mtu Tracking State : Down CSPF Route : Pending (21 retries)
show rsvp neighbor [ip-addr | detail]
Displays Resource Reservation Protocol (RSVP) neighbor information.
all modes
ip-addr |
Optional. Neighbor IP address. Displays detailed information for specified neighbor. |
detail |
Optional. Displays detailed information for all neighbors. |
Displays summary RSVP information for all neighbors.
Use the show rsvp neighbor command to display RSVP neighbor information.
If the RSVP neighbor’s transport IP address differs from its router ID, the IP address specified in the neighbor ip-addr construct must be the RSVP neighbor’s transport IP address.
The following example displays summary RSVP neighbor information for all RSVP interfaces:
[local]Redback>show rsvp neighbor
--- All RSVP Neighbors --- Nbr Address GR Rest-Time Recov-Time State 17.1.1.3 Yes 60 120 Up 20.1.1.1 Yes 30 60 Up 27.27.27.1 No 30 60 Hello Disabled 28.28.28.1 No 30 60 Hello Disabled 31.1.1.2 No 30 60 Hello Disabled
The summary includes the following information for all RSVP neighbors:
Nbr Address = Neighbor address: IP Address
GR = Graceful Restart Enabled: Yes/No
Rest-Time = Number of seconds that Nbr has to send “Hello” after restarting.
Recov-Time = Number of seconds that Nbr has to refresh LSPs after restarting.
State = Up/Down/Hello Disabled/Restarting
The following example displays detailed information for neighbor 17.1.1.3:
[local]Redback>show rsvp neighbor 17.1.1.3
--- RSVP Neighbor 17.1.1.3 --- Intf Name :to-nbrA GR Enabled :Yes Restart Time :60 (sec) Recovery Time :120 (sec) Nbr Restart Time :20 (sec) Nbr Recovery Time :40 (sec) Restart TTD :14 (sec) Recovery TTD :54 (sec) Hello Status :Restarting Nbr Restart Cnt :9 Last Nbr Restart :09:48:21 Wed Oct 15 2008 Nbr flags :0x0010 Nbr Reference Cnt :300
The detailed display includes the following information:
Intf Name = Interface Name GR Enabled = Graceful Restart Enabled: Yes/No
Restart Time = Number of seconds that the local node has to send “Hello” after restarting. Recovery Time = Number of seconds that the local node has to refresh LSPs after restarting. (Restart/Recovery Time is available only if RSVP Hello messages are enabled.)
Nbr Restart Time = Number of seconds that Nbr has to send “Hello” after restarting. Nbr Recovery Time = Number of seconds that Nbr has to refresh LSPs after restarting. (Restart/Recovery Time is available only if RSVP Hello messages are enabled.)
Restart TTD = Number of seconds remaining for Nbr to send “Hello”. Recovery TTD = Number of seconds remaining for Nbr to refresh LSPs.
Hello Status = Enabled/Disabled/Restarting Nbr Restart Cnt = Number of restarts since Nbr discovery.
Last Nbr Restart = Time and date of the last Nbr restart.
Nbr flags = Nbr flags. Nbr Reference Cnt = The number of structures currently referencing the nbr structure. Both path state blocks and resv state blocks can reference the nbr structure, so there is not always a 1-to-1 relationship between the number of LSPs and the Nbr Reference Cnt.
show rsvp track [object-name | detail]
Displays information about a specific RSVP tracking object or for all RSVP tracking objects currently configured on the router.
all modes
object-name |
Optional. Tracking object. |
detail |
Optional. Displays detailed information about all tracking objects currently configured on the router. |
Displays summary information about all RSVP tracking objects that are currently configured on the router.
Use the show rsvp track command to display information about a specific RSVP tracking object or for all RSVP tracking objects currently configured on the router.
The following example shows how to display summary information about all tracking objects currently configured on the router:
[local]Redback#show rsvp track Track Object Member Count Observer Count Status object1 1 0 DOWN Track1 1 0 UP Track-mtu 3 2 UP
The following example shows how to display information about a tracking object called object1:
[local]Redback#show rsvp track object1 Track Object object1 is DOWN Number of members: 1 RSVP interface:1 is DOWN Tracked by 0 observers
The following example shows how to display detailed information about all tracking objects currently configured on the router:
[local]Redback#show rsvp track detail Track Object Track10 is DOWN Number of members: 0 Tracked by 2 observers RSVP LSP:AC1MTU2AZUL RSVP LSP:AC1AG1VERDE Track Object Track3 is DOWN Number of members: 0 Tracked by 0 observers Track Object Track4 is DOWN Number of members: 0 Tracked by 0 observers Track Object Track5 is DOWN Number of members: 0 Tracked by 0 observers Track Object Track6 is DOWN Number of members: 0 Tracked by 0 observers Track Object Track7 is DOWN Number of members: 0 Tracked by 0 observers Track Object Track8 is DOWN Number of members: 0 Tracked by 0 observers Track Object Track9 is DOWN Number of members: 0 Tracked by 0 observers Track Object Track-mtu is UP Number of members: 6 RSVP interface:IPst.2 is UP RSVP interface:IPst.14 is DOWN RSVP interface:abc3 is DOWN RSVP interface:IPst.4 is UP RSVP interface:abc is DOWN RSVP interface:IPst.3 is DOWN Tracked by 1 observers RSVP LSP:AC1_MTU1_azul Track Object Track-new is UP Number of members: 1 Tracked by 0 observers
show secured-arp
Displays secured Address Resolution Protocol (ARP) information.
all modes
This command has no keywords or arguments.
None
Use the show secured-arp command to display secured ARP information.
The following example displays secured ARP information:
[local]Redback>show secured-arp Total number of Secured ARP entries in cache: 1 Host Interface i/f grid Circuit 20.1.1.187/32 to-dhcpclient 0x1000000b 11/1 vlan-id 11 20.2.10.0/24 test 0x10000002 11/2
show service [filter]
Displays enabled and disabled services.
filter |
Optional. Displays service filter information. |
None
Use the show service command to display enabled and disabled services.
Use the optional filter keyword to display service filter information.
The following example displays the output from the show service command:
[local]Redback>show service
Context Services: multiple-contexts enabled card-auto-reload enabled console-break disabled vxworks-log-to-screen enabled upload-coredump disabled crash-dump-dram disabled auto-system-recovery disabled
show snmp {accesses | communities | server | targets | views}
Displays Simple Network Management Protocol (SNMP) information, including usage, configured contexts, communities, SNMP daemon status, targets, and views.
accesses |
Optional. Displays usage. |
communities |
Optional. Displays the communities. |
server |
Optional. Displays the current state of the SNMP daemon and the User Datagram Protocol (UDP) port on which it is currently configured to listen. |
targets |
Optional. Displays configured SNMP targets (notification receivers). |
views |
Optional. Displays the configured Management Information Base (MIB) views. |
None
Use the show snmp command to display SNMP statistics, including usage, configured contexts, communities, notifications, SNMP daemon status, targets, and views.
The following example displays output from the show snmp command with the views keyword:
[local]Redback>show snmp views
restricted system - included non-volatile restricted snmp - included non-volatile restricted snmpEngine - included non-volatile restricted snmpMPDstats - included non-volatile restricted usmStats - included non-volatile
show snmp alarm {active | cleared | model | stats}
Displays Simple Network Management Protocol (SNMP) information for SNMP alarms.
all modes
active |
Display active alarms in Alarm MIB |
cleared |
Display cleared alarms |
model |
Display SNMP alarm model table |
stats |
Display statistics |
None
Use the show snmp alarm command to display SNMP alarm statistics, alarm model configuration, and lists of active and cleared alarms.
The following example displays output from the show snmp alarm command with the cleared keyword:
[local]Redback>show snmp alarm cleared ============================================================================= Object name : Value ============================================================================= alarmClearIndex : 3 alarmClearDateAndTime : 2009-4-9, 12:28:19, -8:0 alarmClearEngineID : 80.0.9.30.83.0.0.30.88.1.45.8d [hex] alarmClearEngineAddressType : ipv4(1) alarmClearEngineAddress : 10.12.49.19 alarmClearContextName : local alarmClearLogIndex : 0 alarmClearNotificationID : interfaces.3.3.4.5 alarmClearResourceId : 0.0 alarmClearModelPointer : 0.0
show snmp ping [status {name ping-test-name} {details} | {result {name ping-test-name}{success | failed {history} {details}} {output}]
Displays information about that status and results of scheduled ping tests.
status |
Displays the status of scheduled ping tests. |
result |
Displays the result of the ping test. |
name ping-test-name |
Limits displayed information to the ping test with the name you identify in the ping-test-name argument. |
success |
Displays ping tests that ran successfully. |
failed |
Displays ping tests that failed. |
history |
Displays a history of ping test results up to 12 ping tests. |
details |
Displays a detailed listing of ping test results. |
None
Use this command to display the status and results of the scheduled ping tests. If a hostname is used as the ping target, the details keyword shows the resolved IP address of the hostname; otherwise, it shows the ping target IP address.
When you run the command from a non-local context, only the ping tests defined within that context will display. If you run the commands from the local context, you can view all defined ping tests and the output is organized by context.
The following example displays output from the show snmp ping command with the result and history keywords:
[local]Redback>show snmp ping result history Context: local, Owner: CLI name idx status sent recv min/max/avg rtt (ms) jitter --------------------- --- ------- ---- ---- -------------------- ---- ip test #3 1 success 15 15 1000/1000/1000 0 ip test #3 2 success 15 15 1000/1000/1000 0 ip test #3 3 failed 15 0 0/0/0 0 ip test #4 1 failed 15 0 0/0/0 0 ip test #4 2 failed 15 0 0/0/0
The following example displays output from the show snmp ping command with the status and details keywords:
[local]Redback>show snmp ping status details Context: local, Owner: CLI name status protocol target freq cnt ------------------- -------- ---------- -------------------- ----- --- ip test enabled ip/icmp ipaddr-or-hostname 86400 15 timeout=60, df, size=nn, pattern=0xff, tos=0xff, ttl=255, src=1.2.3.4 Context: local, Owner: SNMP(test1) name status protocol target freq cnt ------------------- -------- ---------- -------------------- ----- --- ip test enabled ip/icmp ipaddr-or-hostname 86400 15 timeout=60, df, size=nn, pattern=0xff, tos=0xff, ttl=255, src=1.2.3.4
show spanning-tree bridge-name [details]
Shows the spanning-tree information for the bridge instance.
exec
bridge-name |
Name of the bridge. |
details |
Show detailed spanning-tree information. |
Use the show spanning-tree to show the spanning-tree information for the bridge instance; that is, use the command to show the spanning-tree information that applies to the whole SmartEdge bridge.
The following example shows detailed spanning-tree information for the brdgrp1 bridge:
[local]Redback#show spanning-tree brdgrp1 details
show spanning-tree bridge-name circuit circuit-id [details]
Shows the spanning-tree information for specific circuits on the bridge.
exec
bridge-name |
Name of the bridge. |
circuit circuit-id |
Specifies circuits on the bridge. See Table 4 for the expanded syntax for the circuit-id argument. |
details |
Provide detailed spanning-tree information. |
Use the show spanning-tree to show the spanning-tree information for specific circuits on the bridge on the SmartEdge system.
The circuit-id argument is composed of the keywords and arguments as described in the following syntax:
slot/port {ethernet | vlan vlan-id}
Table 4 describes the components of the circuit-id argument:
Field |
Description |
---|---|
slot |
Chassis slot number of the traffic card with the bridged circuits. |
port |
Port number of the port with the bridged circuits. |
ethernet |
Clears all the circuits on the specified Ethernet port. |
vlan vlan-id |
A filter that limits the command to a specified virtual LAN (VLAN) 802.1Q tunnel or PVC. The vlan-id argument is one of the following constructs:
If you specify the VLAN tag value for an 802.1Q tunnel, this command clears subscriber sessions on all the PVCs within the tunnel. The range of values for any VLAN tag value is 1 to 4095. |
The following example shows detailed spanning-tree information specific to the circuits in the Ethernet port 2/1 in the brdgrp1 bridge:
[local]Redback#show spanning-tree brdgrp1 circuit 2/1 ethernet details
show sse {group | partition} [group_name [partition_name]] [detail]
all modes
group |
Displays SSE group information. |
partition |
Displays SSE card partition information. |
group_name |
Optional. Name of the SSE group. Displays information for the specified SSE group. |
partition_name |
Optional. Name of the partition. Displays information for the specified partition. |
detail |
Optional. Displays detailed information for the specified SSE group or partition. |
Displays SSE group or SSE partition information.
See Table 5 for a description of the fields displayed in the output of the command.
Output Field |
Description |
---|---|
Group |
SSE group name |
ID |
SSE group ID: 1 to 32 |
Description |
Group description |
State |
Service state of the SSE group:
|
Redundancy |
SSE group redundancy setting: Network or Disk |
Revert |
Switch mode configured: Enabled, Disabled |
Disk Mode |
Configured disk mode: RAID-0, RAID-1, or Independent |
Switch Trigger Reason |
If applicable, trigger reason for redundancy switch: N/A, Manual, or Auto |
Switch Failed Reason |
If applicable, switch failed reason: Alarm events |
Partition(s) |
Number of partitions configured |
Name |
Name of each partition configured |
ID |
Partition ID: 1 to 16 |
Group Name |
Name of group |
Group ID |
Group ID: 1 to 32 |
State |
Operational status of the partition: Up, Down, Stale |
Size (GB) |
Configured size of the partition |
Percent Used (%) |
Units of data (in GB) used on the partition as a percentage |
Disk |
Disk number, if designated: 1, 2, or All |
Mirrored |
Mirror data to standby disk, if network redundancy is configured: Enabled, Disabled, N/A |
Alarm Low Space |
Alarm for low partition space: Enabled or Disabled |
Trigger Percentage |
Triggering disk space in percentage; clear percentage in brackets |
Alarm(s) |
Alarms triggered on the partition |
Primary |
Primary slot assigned to the group: slot slot_num |
Secondary |
If redundancy is configured, the secondary slot assigned to the group: slot slot_num |
Disk Mode |
Configured disk mode for the group: RAID-0, RAID-1, or Independent |
Redundancy State |
The acting status of the redundancy group. Standalone is assigned for non-redundant groups: Active, Standby, or Standalone |
Disk ID(s) Ready |
Indicates which disks are ready for service: 1, 2, All, or None |
Total Disk Size |
Total disk size available on the slot/disk, rounded to the nearest GB |
Data Status |
The redundancy status of the data on the disk. Sync-in-progress means that the redundancy data is being synchronized from the current active slot/disk: Up-to-date or Sync-in-progress |
Alarm(s) |
Alarm(s) raised for the slot/disk. |
Sync Progress |
If synchronization is happening, it shows the progress as a status bar with percentage completed, as well as size synchronized and total to be synchronized. |
Time Remaining |
Estimated time remaining for the sync to complete: HH:MM:SS |
Speed |
Current speed of the sync in KB/sec |
Mean Speed |
Mean speed of the sync in KB/sec |
[local]Redback#show sse group Group ID Redundancy Disk Mode Slot State ----------------------------------------------------------------- grp1 1 network-redundant Independent 2 (5) Down
[local]Redback#show sse group detail Name : grp1 ID : 1 Description : ------------------------------------------------------------------------ State : Up Redundancy : network-redundant Disk Mode : Independent Revert : no revert Switch Reason : Standby INS Switch Failed Reason: No Reason Alarms : NONE Partition(s) : -------------------------------------------- Name : ptn1 ID : 1 Group Name : grp1 Group ID : 1 State : Up Size (GB) : 2 Percent Used : 9 Disk : 1 Mirrored : Enabled Alarm Low Space : Enabled Trigger Percentage : 80 (clear 70) Alarms : NONE Name : ptn2 ID : 2 Group Name : grp1 Group ID : 1 State : Up Size (GB) : 2 Percent Used : 2 Disk : 1 Mirrored : Disabled Alarm Low Space : Enabled Trigger Percentage : 80 (clear 70) Alarms : NONE Primary Slot : 2 -------------------------------------------- Redundancy State : Active Slot State : Up Disk ID(s) Ready : All Total Size (GB) : 268 Data Status : Up-To-Date Active Alarms : NONE Secondary Slot : 5 -------------------------------------------- Redundancy State : Standby Slot State : Up Disk ID(s) Ready : 1 Total Size (GB) : 134 Data Status : Up-To-Date Active Alarms : NONE
[local]Redback#show sse partition Group ID Partition ID Size (GB) Disk State ---------------------------------------------------------------- grp1 1 ptn1 1 2 1 Up grp1 1 ptn2 2 2 1 Up
[local]Redback#show sse partition detail Name : ptn1 ID : 1 Group Name : grp1 Group ID : 1 State : Up Size (GB) : 2 Percent Used : 9 Disk : 1 Mirrored : Enabled Alarm Low Space : Enabled Trigger Percentage : 80 (clear 70) Alarms : NONE Name : ptn2 ID : 2 Group Name : grp1 Group ID : 1 State : Up Size (GB) : 2 Percent Used : 2 Disk : 1 Mirrored : Disabled Alarm Low Space : Enabled Trigger Percentage : 80 (clear 70) Alarms : NONE
show sse {group | partition} counters [group_name [partition_name]]
all modes
group |
Displays SSE group information. |
partition |
Displays SSE card partition information. |
group_name |
Name of the SSE group. |
partition_name |
Name of the partition. |
Displays SSE group or SSE partition counters.
[local]Redback#show sse group counters Name : grp1 ID : 1 Redundancy : network-redundant Primary Slot : 2 Redundancy State : Active Secondary Slot : 5 Redundancy State : Standby Partition(s) : ------------------------------------------------------------------------ timestamp: 11486967468 timestamp secs: 11486 timestamp usecs: 967468 Name : ptn1 ID : 1 Group Name : grp1 Group ID : 1 Disk Allocated : 1 Partition Size (GB) : 2 Percent Used : 9 Percent Available : 91 Network Send : 2097100 Network Received : 0 Disk Write (KB) : 12 Disk Read (KB) : 2097826 Activity Log : 1 Bit Map : 128 Local Count : 0 Local Pending : 0 Unacknowledged : 0 Application Pending : 0 timestamp: 11486968702 timestamp secs: 11486 timestamp usecs: 968702 Name : ptn2 ID : 2 Group Name : grp1 Group ID : 1 Disk Allocated : 1 Partition Size (GB) : 2 Percent Used : 2 Percent Available : 98 Network Send : 0 Network Received : 0 Disk Write (KB) : 32 Disk Read (KB) : 738 Activity Log : 2 Bit Map : 0 Local Count : 0 Local Pending : 0 Unacknowledged : 0 Application Pending : 0
show ssh-attributes
Displays information about configured Secure Shell (SSH) attributes and the number of current connections.
This command has no keywords or arguments.
None
Use the show ssh-attributes command to display information about configured SSH attributes and the number of current connections.
The following example displays SSH attributes:
[local]Redback>show ssh-attributes
ssh attributes -------------- start-drop 50 (connections) rate-drop 100 (percentage) full-drop 50 (connections) current 0 (connections)
show static route [print-prefix] [all]
Displays static route information.
all modes
print-prefix |
Optional. Displays the IP address and prefix length for static routes with multiple next hops. By default, entries in the Prefix field are left blank. |
all |
Optional. Displays static route information for all contexts. |
None
Use the show static route command to display static route information.
Table 6 describes the show static route command output fields.
Field |
Description |
---|---|
Prefix |
IP address and prefix length. |
Best |
|
NType |
Next-hop type. The types can be addr (IP address), intf (interface), dvsr, and cntx (context). The dvsr next-hop type is a special type of IP address. |
Addr/Intf/Cntx |
Detail next-hop information. The information displayed can either be an IP address, an interface name, a context name, or null0 (a special interface name). |
NS |
Next-hop status. The status is either up or dn (down). It reflects the status of either the next-hop IP address reachability, the next-hop interface status, or the next-hop context. |
Dist |
Route distance to be advertised into the RIB. |
P |
An asterisk (*) indicates that the route is a permanent announced route. |
Tag |
Tag value of the prefix. |
The following example displays output from the show static route command:
[local]Redback>show static route
Prefix Best NType Addr/Intf/Cntx NS Dist P Tag 8.1.1.1/30 yes dvsr 165.63.39.15 up 1 0x0 10.1.1.0/24 yes intf ether3/1 up 1 0x0 no intf op-net-lan up 10 0x0 10.1.2.0/24 yes intf to-redback up 1 0x0 10.11.12.0/24 yes cntx foo up 1 0x0 20.0.0.0/8 yes intf to-redback up 1 0x0 yes addr 165.63.39.1 up 1 0x0 30.0.0.0/8 yes intf null0 up 1 0x0 40.1.0.0/16 no- cntx vpn-abc dn 1 0x0 50.1.2.0/24 yes addr 165.63.39.2 up 1 * 0x0 Total static route in context local: 8, total path: 10
To display the basic subscriber status fields:
show subscribers [{agent-circuit-id id | agent-remote-id id | all | {session slot/port[:chan-num[:sub-chan-num]] [circuit-id]} | session l2tp lns id | username subscriber}]
To display the digital subscriber line (DSL) attributes associated with subscribers:
show subscribers access-line [{agent-circuit-id id | agent-remote-id id | all | {session slot/port[:chan-num[:sub-chan-num]] [circuit-id]} | session l2tp lns id | username subscriber}]
To display the attributes of active subscriber sessions:
show subscribers active [{agent-circuit-id id | agent-remote-id id | all | {session slot/port[:chan-num[:sub-chan-num]] [circuit-id]} | session l2tp lns id | username subscriber}]
To display the Mobile IP attributes associated with subscribers:
show subscribers mobile-ip [{agent-circuit-id id | agent-remote-id id | all | {session slot/port[:chan-num[:sub-chan-num]] [circuit-id]} | session l2tp lns id | username subscriber}]
To display the authentication, authorization, and accounting (AAA) logs of subscribers:
show subscribers log [{{session slot/port[:chan-num[:sub-chan-num]] [circuit-id]} | session l2tp lns id | username subscriber}]
To display a summary of subscriber information:
show subscribers summary [all]
To display IP information associated with subscribers:
show subscribers address username subscriber
Displays subscriber information.
all modes
agent-circuit-id id |
Optional. A filter that limits the information displayed to the subscriber specified by the agent circuit ID in a subscriber record. Enter the id argument as a structured subscriber username in the form subscriber@context. |
agent-remote-id id |
Optional. A filter that limits the information displayed to the subscriber specified by the agent remote ID in a subscriber record. Enter the id argument as a structured subscriber username in the form subscriber@context. |
all |
Optional. Displays information about all subscribers in all contexts. This keyword is available only to administrators in the local context. |
session |
Optional. Limits the command output to the specified session or circuit. |
slot |
Optional. Chassis slot number for a traffic card. |
port |
Optional. Port number on the specified traffic card. |
chan-num |
Optional. Channel number on the specified port. If omitted, this command applies to all channels on the specified port. This option is valid only on channelized DS-3, E1, OC-12 and STM-1 traffic cards. Table 8 lists the range of values for the chan-num and sub-chan-num arguments for various types of channelized ports. |
sub-chan-num |
Optional. Subchannel number in the specified channel. If omitted, this command applies to all subchannels in the specified channel. This option is valid only on channelized OC-12 and STM-1 traffic cards. Table 8 lists the range of values for the chan-num and sub-chan-num arguments for various types of channelized ports. |
circuit-id |
Optional. A subscriber session identifier, or a subscriber username that filters which subscriber information this command displays. See Table 7 for information about the circuit-id argument. |
l2tp lns id |
Optional. Limits the output of the command output to the specified Layer 2 Tunneling Protocol (L2TP) network server (LNS) circuit. |
username subscriber |
Optional. Limits the command output to subscribers specified by a subscriber name. Enter the subscriber argument as a structured subscriber username in the form subscriber@context. |
access-line |
Optional. Displays the DSL attributes. |
active |
Optional. Displays the attributes of active subscriber sessions. |
mobile-ip |
Optional. Displays the Mobile IP attributes for the specified subscriber sessions. |
log |
Optional. Displays the AAA log. |
summary |
Optional. Displays the total number of subscribers and their encapsulations in the current context. |
address |
Optional. Displays the IP information. |
Displays information for all active subscribers in the current context.
Use the show subscribers command to display subscriber information. This includes basic subscriber status fields, DSL attributes, attributes of active subscriber sessions, Mobile IP attributes, AAA log or logs, a summary of subscriber information, and IP addresses associated with subscribers.
The circuit-id argument represents the following keywords and arguments; see Table 7:
clips [clips-session] | pppoe [pppoe-session] | vlan-id vlan-id [pppoe [pppoe-session] | clips [clips-session]] | vpi-vci vpi vci [pppoe [pppoe-session] | clips [clips-session]]
Construct |
Description |
---|---|
clips clips-session |
A filter that limits the command to a specified CLIPS circuit on a port, channel, 802.1Q PVC, or ATM PVC. If the CLIPS circuit is on an 802.1Q or ATM PVC, also specify the circuit identifier for the 802.1Q or ATM PVC. If the session is not specified, the command applies to all CLIPS sessions in the context. The range of values for the clips-session argument is 1 to 262,144. |
pppoe pppoe-session |
A filter that limits the command to a specified PPPoE session. If the pppoe-session argument is not specified, the command applies to all PPPoE sessions in the context. |
vlan-id vlan-id |
A filter that limits the command to a specified virtual LAN (VLAN) 802.1Q tunnel or PVC. The vlan-id argument is one of the following constructs:
If you specify the VLAN tag value for an 802.1Q tunnel, this command clears subscriber sessions on all the PVCs within the tunnel. The range of values for any VLAN tag value is 1 to 4,095. |
vpi-vci vpi vci |
A filter that limits the command to a specified ATM PVC. The ATM PVC is specified by the virtual path identifier (VPI) and virtual circuit identifier (VCI). The range of values is 0 to 255 and 1 to 65,534, respectively. |
The slot and port assignments for the SmartEdge routers are described in their respective hardware guides.
Table 8 lists the range of values for the chan-num and sub-chan-num arguments for various types of channelized ports. The SmartEdge 100, SmartEdge 800s, and SmartEdge 1200 routers do not support channelized ports.
Port |
Channel Types |
chan-num Range |
sub-chan-num Range |
---|---|---|---|
Channelized OC-12 |
DS-3, DS-1 |
1 to 12 |
1 to 28 |
Channelized STM-1 |
E1, DS-0 channel group |
1 to 63 |
1 to 31 |
Channelized DS-3 |
DS-1 |
1 to 28 |
– |
Channelized E1 |
DS-0 channel group |
1 to 31 |
– |
Use the access-line keyword to display information about DSL line attributes for each subscriber. The output information includes the parameters learned from the DSL attribute extension Type, Length, Value (TLV) in the General Switch Management Protocol (GSMP) Port Up message for the DSL.
The DSL attributes are learned from the DSL access multiplexer (DSLAM). They can be learned by GSMP messages and from PPPoE or DHCP tags during a subscriber session setup. Each learned attribute is preceded by the words Access Node Control Protocol (ANCP) or DSL Forum (DSLF) when printed. This indicates the mechanism by which it was learned. For example, ANCP means it was learned by ANCP; DSLF was learned from a tag during subscriber session setup; and so forth.
Table 9 lists the types of DSL data and the values that this command can display.
Type of Data |
Value |
---|---|
Agent-Circuit-ID |
This includes DSLAM slot, port and channel number. |
Internal Circuit |
This includes the internal circuit number, slot, port and channel numbers. |
Neighbor ID |
Neighbor ID number |
DSL Line State |
|
DSL Data Rates |
|
Use the show bindings command to get the binding information that optionally can be specified in the show subscribers command. For information on the show bindings command, see the Command List.
The show subscribers command used with the active keyword, provides information on the dynamic policy rules applied to active subscriber sessions.
The slot and port numbering rules for the SmartEdge 100, SmartEdge 400, and SmartEdge 800 routers are described in their respective hardware guides.
The following example shows the default output:
[local]Redback>show subscribers Type CIRCUIT SUBSCRIBER CONTEXT START TIME ----------------------------------------------------------------------- PPPOE 00001 pppoe@redback.com company1 JUN 30 17:46:49 2005 VIPSRC 00002 00:dd:00:00:00:01 isp1 JUN 30 00:03:11 2005 VIPSRC 00003 00:dd:00:00:00:02 isp1 JUN 30 00:03:01 2005 VIPSRC 00004 00:dd:00:00:00:03 isp1 JUN 30 00:03:01 2005 VIPSRC 00005 00:dd:00:00:00:04 isp1 JUN 30 00:03:11 2005 VIPSRC 00006 00:dd:00:00:00:05 isp1 JUN 30 00:03:11 2005 ----------------------------------------------------------------------- Total=6 Type Authenticating Active Disconnecting PPP 0 0 0 PPPoE 0 1 0 DOT1Q 0 0 0 CLIPs 0 5 0 ATM-B1483 0 0 0 ATM-R1483 0 0 0
The following example displays the information for an active subscriber; it includes both the absolute timeout action and traffic limit action fields:
[local]Redback>show subscribers active username client32@lns.com
client32@lns.com Circuit L2TP LNS 8744119 Internal Circuit 255/16:1023:63/5/2/8744119 Current port-limit unlimited context-name lns (applied) ip pool (applied from sub_default) absolute timeout action 1 (applied from sub_default) traffic limit action 1 (applied from sub_default) ip address 192.168.27.2 (applied from pool) timeout absolute 60 (applied) timeout idle 60 (applied)
...
The following example shows the dynamic policy access control lists (ACLs) applied in the forward direction to the active subscriber session usr1@local. For information on the dynamic policy fields displayed in both show commands, see the show access-group command in the Command List:
[local]Redback>show subscribers active usr1@local Circuit 2/1 clips 1 Internal Circuit 2/1:1023:63/4/2/1 Interface bound clips1 Current port-limit unlimited ip address 11.1.0.1 (applied) forward policy in forpol (applied) dynamic policy acl (applied in: fwd) ip in forward srcip 11.1.0.51/32 tos 0x08 0x1e class c1 fwd ip in forward srcip 11.1.0.51/32 tos 0x40 0xe0 class c1 fwd ip in forward srcip 11.1.0.51/32 tos 0x48 0xfe class c1 fwd ip in forward srcip 11.1.0.51/32 tos 0x0c 0x1e class c1 fwd ip in forward srcip 11.1.0.51/32 dscp af41 class c1 fwd
Use the show subscribers active all command to view if the RFlow profile is applied to the subscriber in the ingress direction (in), egress direction (out), or bi-directionally (both). In the following example, you will see that the flow ip profile has been applied at ingress:
[local]Redback# show subscribers active all client2162833@local Circuit 4/1:1 vpi-vci 33 145 pppoe 2450 Internal Circuit 4/1:1:63/1/2/8193 Interface bound subs Current port-limit unlimited ip pool subs (applied from sub_default) ip source-validation 1 (applied from sub_default) ip address 2.2.0.1 (applied from pool) flow ip profile ingress-flow:in (applied)
The following example includes DSL fields in the command output:
[local]Redback>show subscribers access-line
test@local Agent Circuit ID "DSLAM1-slot0-port0-channel2" Internal Circuit 4/3:1023:63/1/2/6 Neighbor ID 10.13.16.98:6068 ANCP Line State SHOWTIME ANCP Actual Data Rate Downstream (kbps) 7777 (applied)
For ports on channelized OC-12 or STM-1 traffic cards, the syntax is:
show system alarm [all | slot[/port[:chan-num[:sub-chan-num]]]]
For channelized ports on DS-3 or E1 traffic cards, the syntax is:
For SSE cards, the syntax is:
show system alarm [all | sse [group_ID [partition_ID]]]
For clear-channel ports on DS-3, E3, or E1 traffic cards, or ports on Asynchronous Transfer Mode (ATM) OC, ATM DS-3, Ethernet, or Packet over SONET/SDH (POS) traffic cards, the syntax is:
show system alarm [all | slot[/port]]
Displays system-level, card-level, port-level, channel-level, or subchannel-level alarms.
all |
Optional. Displays alarms at all levels. |
slot |
Optional. Chassis slot number of the traffic card for which card-, port-, channel-, and subchannel-level alarms are displayed. |
port |
Optional. Card port number of the port for which port-, channel-, and subchannel-level alarms are displayed. |
chan-num |
Optional. Channel number for which channel- and subchannel-level alarms are displayed. The range of values depends on the type of port; see Table 10 for the range of values. |
sub-chan-num |
Optional. Subchannel number for which subchannel-level alarms are displayed. The range of values depends on the type of port; see Table 10 for the range of values. |
sse |
Optional. Displays alarm information for all SSE group and partition alarms. |
group_ID |
Optional. Displays alarm information for the specified SSE group ID. See the output of the show sse group command for valid values. |
partition_ID |
Optional. Displays alarm information for the specified partition ID. See the output of the show sse partition command for valid values. |
Displays system-level alarms only.
Use the show system alarm command to display system-level, card-level, port-level, channel-level, or subchannel-level alarms.
Table 10 lists the range of values for the chan-num and sub-chan-num arguments for various types of channelized ports.
Port |
Channel Types |
chan-num Range |
sub-chan-num Range |
---|---|---|---|
Channelized OC-12 |
DS-3, DS-1 |
1 to 12 |
1 to 28 |
Channelized STM-1 |
E1, DS-0 channel group |
1 to 63 |
1 to 31 |
Channelized DS-3 |
DS-1 |
1 to 28 |
– |
Channelized E1 |
DS-0 channel group |
1 to 31 |
– |
Each succeeding argument restricts the display to the alarms at that level and below and to the alarms for that card, or port, channel, or subchannel.
Use the show port detail command (in any mode) to view the alarms for a port. See the Command List for more information.
Use the show diag command (in any mode) to view the results of the power-on diagnostics (POD) or on-demand diagnostics (ODD).
The following example displays system-level alarms only:
[local]Redback>show system alarm
Timestamp Type Source Severity Descriptions -------------------------------------------------------------------------------------- Dec 16 19:32:01 chassis Minor Chassis power failure - side B
The following example displays all system-level alarms:
[local]Redback#show system alarm all Timestamp Type Source Severity Description --------------------------------------------------------------------------- Jul 27 13:24:35 chassis Minor Chassis power failure - side A1 Jul 27 13:24:35 chassis Minor Chassis power failure - side A2 Jul 27 16:27:32 sse 5d2 Major Hard disk missing Jul 27 13:24:36 xcrp4-base 7 Major Backup fail: peer dead Jul 27 13:24:36 xcrp4-base 8 Critical Controller missing Jul 27 13:24:46 xcrp4-base 8 Major Controller auto switch completed
The following example displays alarms at the traffic card level and below only; in this case, the traffic card is not installed:
[local]Redback#show system alarm 4
Timestamp Type Source Severity Descriptions --------------------------------------------------------------------------- Dec 10 18:48:33 ch-oc12ds3-1-port 4 Critical Circuit pack missing
The following example displays alarms at the port-level and below only; in this case, only a channel alarm is present:
[local]Redback#show system alarm 13/2
Timestamp Type Source Severity Descriptions --------------------------------------------------------------------------- Dec 10 18:48:49 oc12-4-port 13/2:1 Major Path alarm indication signal (AIS-P)
show system nvlog
Displays the contents of nonvolatile memory (NVRAM) on the controller card to which you are connected.
This command has no keywords or arguments.
None
Use the show system nvlog to display the contents of NVRAM on the controller card to which you are connected. The NVRAM stores logs of trap- and panic-related messages from the operating system and can be used to help debug system crashes in the absence of a local console (connected to the Craft 2 port). If your system does not support NVRAM, you receive the following error message: This XCRP doesn't support this feature.
The following example displays the contents of the NVRAM on the active controller card:
[local]Redback>show system nvlog
panic: testing Redback: dumpsys called dumping to dev 10,33 offset 8 dump succeeded !!!vxWorks sent REBOOT intr, will shutdown BSD!!! !!!vxWorks sent REBOOT intr, will shutdown BSD!!! !!!vxWorks sent REBOOT intr, will shutdown BSD!!!
show tacacs+ server [{{ip-addr | hostname} [port tcp-port]}]
Displays information for one or all Terminal Access Controller Access Control System Plus (TACACS+) servers in the current context.
all modes
ip-addr |
Optional. IP address of the TACACS+ server for which more detailed information is to be displayed. Additional information includes detailed error and status counters, such as packets received and transmitted. |
hostname |
Optional. Hostname of the TACACS+ server. |
port tcp-port |
Optional. TACACS+ server Transmission Control Protocol (TCP) port. The range of values is 1 to 65,536. If no port is specified, TCP port number 49 is used. |
None
Use the show tacacs+ server command to display information for one or all TACACS+ servers in the current context, including the IP address and the key set by the tacacs+ server command (in context configuration mode), and the values set by the tacacs+ max-retries and tacacs+ timeout commands (in context configuration mode).
Use the ip-addr or hostname argument to display detailed information for a particular server; otherwise, the system displays summary information for all servers in the context.
The following example displays summary information for all TACACS+ servers in the context:
[local]Redback#show tacacs+ server
IP Address/Hostname Port Timeout/Max-Tries Key ----------------------------------------------------------------- 10.12.121.211 49 5/1 mykey 10.12.209.171 49 5/1 otherkey
The following example displays information for a specific TACACS+ server:
[local]Redback#show tacacs+ server 10.12.211.121
IP Address/Hostname Port State In-svc Key ----------------------------------------------------------------------- 10.12.211.121 49 untried alive mykey Counter Value ------- ---------- Current sessions 0 Transmitted packets 8 Received packets 8 Dropped packets 0 Connection errors 0 Connection timeouts 0 Host unreachable errors 0 Transmission errors 0 Reception errors 0 Authentication timeouts 0 Authorization timeouts 0 Accounting timeouts 0
show tcp [{brief [all] | md5 | statistics | tcb tcpcb-addr}]
Displays Transmission Control Protocol (TCP) Internet connections, statistics, and keepalive settings.
all modes
brief |
Optional. Displays active Internet connections. |
all |
Optional. Displays active Internet connections, including servers. Used with the brief keyword. |
md5 |
Optional. Displays Message Digest 5 (MD5) entries. |
statistics |
Optional. Displays TCP statistics. |
tcb tcpcb-addr |
Optional. TCP connection for which details are to be displayed. |
None
Use the show tcp command to display TCP Internet connections, statistics, and keepalive settings.
The following example displays output when the statistics keyword is specified:
[local]Redback>show tcp statistics
tcp: 85778 packets sent 33921 data packets (934491 bytes) 323 data packets (91638 bytes) retransmitted 26522 ack-only packets (77668 delayed) 0 URG only packets 0 window probe packets 24871 window update packets 141 control packets 123389 packets received 33053 acks (for 936341 bytes) 537 duplicate acks 0 acks for unsent data 102667 packets (37396219 bytes) received in-sequence 132 completely duplicate packets (189 bytes) 0 old duplicate packets 167 packets with some dup. data (232 bytes duped) 39 out-of-order packets (13 bytes) 0 packets (0 bytes) of data after window 0 window probes 7 window update packets 1 packet received after close 0 discarded for bad checksums 0 discarded for bad header offset fields 0 discarded because packet too short 26 connection requests 75 connection accepts 82 connections established (including accepts) 98 connections closed (including 24 drops) 18 embryonic connections dropped 32255 segments updated rtt (of 32538 attempts) 333 retransmit timeouts 1 connection dropped by rexmit timeout 0 persist timeouts (resulting in 0 dropped connections) 110 keepalive timeouts 86 keepalive probes sent 24 connections dropped by keepalive 6023 correct ACK header predictions 89333 correct data packet header predictions 224 PCB hash misses 64 dropped due to no socket 0 connections drained due to memory shortage 1 bad connection attempt 79 SYN cache entries added 0 hash collisions 75 completed 0 aborted (no space to build PCB) 0 timed out 0 dropped due to overflow 0 dropped due to bucket overflow 4 dropped due to RST 0 dropped due to ICMP unreachable 1 SYN,ACK retransmitted 1 duplicate SYN received for entries already in the cache 0 SYNs dropped (no route or no space)
The following example displays output when a TCP connection address is specified:
[local]Redback>show tcp tcb 0xe091a630
TCP Protocol Control Block at 0xe091a630: Timers: REXMT: 1430 PERSIST: 0 KEEP: 15827 2MSL: 0 State: ESTABLISHED, flags 0x38a0, inpcb 0xe090ca80 rxtshift 0, rxtcur 3, dupacks 0 peermss 498, ourmss 8152, segsz 498 snd_una 2215311423, snd_nxt 2215311425, snd_up 2215311423 snd_wl1 16681764, snd_wl2 2215311423, iss 2215310590, snd_wnd 8271 rcv_wnd 24456, rcv_nxt 16681766, rcv_up 16681764, irs 16681574 rcv_adv 16706222, snd_max 2215311425, snd_cwnd 51294, snd_ssthresh 1073725440 max_sndwnd 8466 idle 0, rtt 1, rtseq 2215311423, srtt 35, rttvar 3, rttmin 2 oobflags 0, iobc 0, softerror 0 snd_scale 0, rcv_scale 0, req_r_scale 0, req_s_scale 0 ts_recent 0, ts_regent_age 0, last_ack_sent 16681766
The following example displays the output of this command when no keywords or arguments are specified:
[local]Redback>show tcp Active Internet connections PCB Recv-Q Send-Q Local Address Foreign Address State 99e1a28 0 0 10.12.49.56.23 155.53.44.159.38903 ESTABLISHED 99e1960 0 0 10.12.49.56.23 155.53.44.159.43022 ESTABLISHED 99e1898 0 0 127.0.2.5.64524 127.0.2.3.6667 ESTABLISHED 99e17d0 0 0 127.0.2.5.56326 *.* LISTEN 99e1708 0 0 127.0.2.5.57435 127.0.2.3.6667 ESTABLISHED 99e1640 0 0 127.0.2.5.51241 127.0.2.3.6666 ESTABLISHED 99e1578 0 0 127.0.2.5.54221 127.0.2.3.6666 ESTABLISHED IP Path MTU discovery is enabled TCP keep-alive idle = 14400 TCP keep-alive interval = 150 TCP keep-alive count = 8
show tech-support [ase]
Displays system information that helps your technical support representative resolve issues.
ase |
Optional. Connects to each ASP in the system and collects debug and status information for use by technical support. (1) |
(1) This keyword, although visible in the CLI, is not available for SM
family platforms.
None
Use the show tech-support command to display information that helps your technical support representative resolve issues. The information contains software version information, system uptime, task information, configuration information, and current state of each traffic card.
Use the ase option to display information for each ASP in the system.
The following example displays output from the show tech-support command in the order that they appear (in the interests of brevity, only the headings are listed):
[local]Redback#show tech-support ------------------ Current time ------------------- Mon Jun 27 10:00:01 PDT 2005 ------------------ Version Info ------------------- Redback Networks SmartEdge OS Version SE800-5.0.5-Release Built by sysbuild@@lx-lsf93 Mon Jan 23 10:00:01 PDT 2006 Copyright (C) 1998-2006, Redback Networks Inc. All rights reserved. System Bootstrap version is PowerPC,1.0b1266 Router Up Time - 21 hours 26 minutes 23 secs ------------------ Release info ------------------- Installed releases: p01: active (will be booted after next reload) ---------------------------------------------- Version SE800-5.0.3.0-Release Built on Mon Dec 19 10:00:01 PDT 2005 Copyright (C) 1998-2003, Redback Networks Inc. All rights reserved. p02: alternate -------------- Version SE800-5.0.3.0-Release Built on Mon Dec 19 01:00:03 PDT 2005 Copyright (C) 1998-2005, Redback Networks Inc. All rights reserved. ------------------ show chassis --------------- . ------------------ Redundancy info --------------- . ------------------ show configuration--------------- . ------------------ Command history--------------- . ------------------ Hardware details --------------- . ------------------ Memory Info ------------------- . ------------------ Crashfile information ---------- . ------------------ Process Crash Info ------------ . ------------------ show task info------------------ . ----------------- Interface Details --------------- . ----------------- Route Table Summary -------------- . ----------------- Multicast Route ----------------- . ----------------- Linecard FIB Info --------------- . ----------------- Linecard Info ------------------- . ----------------- Port Details -------------------- . ----------------- Port Counters -------------------- . ----------------- Database Info ---------------------- .
show terminal
Displays terminal settings for the current session.
This command has no keywords or arguments.
None
Use the show terminal command to display terminal settings for the current session.
The following example displays the terminal settings for the current session:
[local]Redback>show terminal terminal name = /dev/ttyp0 terminal width = 98 terminal length = 50 terminal monitor = disabled
show transaction
Displays information about outstanding configuration database transactions made by other administrators in all configuration modes or created by internal processes.
This command has no keywords or arguments.
None
Use the show transaction command to display information about outstanding configuration database transactions made by other administrators in all configuration modes, or created by internal processes. Outstanding transactions are those that have been configured by other administrators or started by an internal process, but have not yet been committed to the configuration database. Table 11 lists the possible states that might be displayed for a transaction.
State |
Description |
---|---|
Active |
Transaction is active for configuration changes. |
Ready |
Transaction just got the lock it was waiting for and is ready to proceed. |
Blocked |
Transaction is blocked waiting for a lock. The information field displays the transaction ID that holds the lock. |
Blocked on User |
Transaction is blocked by administrator input on whether to continue waiting for the lock to clear. The information field displays the transaction ID that holds the lock. |
Pending Rollback |
Administrator has requested to stop waiting for the lock and the system is preparing to rollback the current command. |
Abort |
Transaction is being erased. |
Committing |
Transaction is marked for commit. |
Commit - Duplicated |
Transaction is duplicated to the standby controller card. (1) |
Commit - Duplicated |
Transaction is duplicated to the standby controller card. |
Commit - Synched |
Transaction is committed on the standby controller card.(2) |
Commit - Synched |
Transaction is committed on the standby controller card. |
Committed |
Transaction has completed the committing on the active controller card. |
Commit - Blocked |
Commit is held up because of a global database lock. Waiting to commit after the lock is clear. |
Waiting to Commit |
Transaction has been time committed. It will be committed at a certain time. The information field displays the time until the commit. |
Invalid |
Transaction is invalid. |
(1) The SmartEdge 100 router has a single controller
card. The Commit-Duplicated and Commit-Synched transaction
states apply only to SmartEdge routers with dual controller cards.
(2) The SmartEdge 100 router has a single controller card. The Commit-Duplicated
and Commit-Synched transaction states apply only to SmartEdge routers with dual controller
cards.
The following example shows the outstanding database transactions created, but not committed, by the admin, admin1, and admin2 administrators:
[local]Redback>show transaction
TID State Sequence State Information User Comment ------------------------------------------------------------------------------- 1037 Blocked 73544 Waiting on TID 1035 admin1 adding circuit under port 1 1035 Active 3634 None admin1 changing port 1 1032 Commit - Duplicated 564654 None admin1 1026 Waiting to Commit 2343564 Committing in 25 min admin adding admin2 at midnight 1022 Active 565 None admin 1011 Abort 84454 None admin deleting admin2
To show information about Generic Routing Encapsulation (GRE) tunnels the syntax is:
show tunnel gre [name tunl-name | peer peer-name | remote remote-IP] [detail]
To show information about IP-in-IP tunnels the syntax is:
show tunnel ipip [name tunl-name | remote remote-IP] [detail]
To show information about automatic IP Version 6 (IPv6) tunnels the syntax is:
show tunnel ipv6-auto [name tunl-name | remote remote-IP] [detail]
To show information about manual IPv6 tunnels the syntax is:
show tunnel ipv6-manual [name tunl-name | remote remote-IP] [detail]
Displays information about tunnels currently configured in the SmartEdge system.
all modes
gre |
Displays information for GRE tunnels. |
ipip |
Displays information for IP-in-IP tunnels |
ipv6-auto |
Displays information for automatic IPv6 tunnels. |
ipv6-manual |
Displays information for manual IPv6 tunnels. |
name tunl-name |
Optional. The name of the tunnel for which information is displayed. |
peer peer-name |
Optional. The name of the GRE peer for which information is displayed. |
remote remote-IP |
Optional. The IP address of the remote interface to a tunnel for which information is displayed. |
detail |
Optional. Specifies the output provides fullest details. |
When the tunnel type is specifed, but the name, remote address. and peer name are not specified, all tunnels of that type are displayed.
Use the show tunnel command to display information about tunnels currently configured in the SmartEdge system. Use the show tunnel client command on Section 1.43 to find information about dynamic tunnel clients that are registered with the tunnel manager.
The following fields can appear in the output of the show tunnel command.
Field |
Description |
---|---|
Name |
Name of the tunnel. |
Context |
Context in which the tunnel was created. |
Type |
IPv6-auto, IPv6-manual, IP-in-IP, or GRE tunnel. |
MTU |
MTU of tunnel. |
Local IP |
Local IP address of the tunnel. |
Remote IP |
Remote IP address of the tunnel. |
State |
The tunnel states can be:
|
Bound to |
Interface and context to which tunnel circuit is bound. |
(1) If the GRE tunnel has no circuits configured, the state is always
down, even after you have entered the no shutdown command
(in GRE peer configuration mode).
Use the uptime keyword to display the amount of time the tunnel circuit is in the Up state.
(Example 1) The following example shows how to display information for the GRE peer named toBoston:
[local]Redback>show tunnel gre peer toBoston
Name Context Type MTU Local-IP Remote-IP State toBoston local gre 1468 11.1.1.1 11.1.1.1 Down
(Example 2) The following example shows how to display detailed information information for the toChicago GRE tunnel in the local context:
[local]Redback>show tunnel name gre toChicago detail ::::: Tunnel : toChicago Key : - Remote IP : 2.2.2.2 Local IP : 192.168.1.5 Tnl Type : GRE State : Down Bound to : Circuit ID: 1 Internal Hdl: 255/4:1023:63/0/1/1 Tunnel is User Configured local-ip 192.168.1.5, context-for-local-ip: local mtu 1468 log-state-changes no clear-df no Keep-alive 0 seconds, retries 0 destination DOWN on nhop mgmt interface resolved on grid 0x10000000 Tunnel ID: gre 1 Circuit ID Internal: 255/4:1023:63/0/1/1
show tunnel client client-name [context ctx-name] [detail]
Displays information about dynamic tunnel clients that are registered with the tunnel manager.
client-name |
Name of client. |
context ctx-name |
Optional. Name of context. |
detail |
Optional. Displays detailed information about dynamic tunnel clients that are registered with the tunnel manager. |
When entered without any optional syntax, the show tunnel client command displays all dynamic tunnel clients that are registered with the tunnel manager.
Use the show tunnel client command to information about dynamic tunnel clients registered with the tunnel manager.
The following example shows how to display information about all dynamic tunnel clients that are registered with the tunnel manager in all contexts:
[local]Redback>show tunnel client Tunnel client information summary --------------------------------------------------------- Client Name : mobile-ip (client-id 2 Context Name : local IPIP Tunnel Count : 0 GRE Tunnel Count : 0 Register State : Registered Restart State : Alive --------------------------------------------------------- Client Name : mobile-ip (client-id 2) Context Name : fa-ctx IPIP Tunnel Count : 0 GRE Tunnel Count : 0 Register State : Registered Restart State : Alive
The following example shows how to display information about dynamic tunnel client named mobile-ip in all contexts that it has registered with tunnel manager:
[local]Redback>show tunnel client mobile-ip Tunnel client information summary --------------------------------------------------------- Client Name : mobile-ip (client-id 2) Context Name : local IPIP Tunnel Count : 0 GRE Tunnel Count : 0 Register State : Registered Restart State : Alive --------------------------------------------------------- Client Name : mobile-ip (client-id 2) Context Name : fa-ctx IPIP Tunnel Count : 0 GRE Tunnel Count : 0 Register State : Registered Restart State : Alive
The following example shows how to display information about dynamic tunnel client named mobile-ip, that is registered with the tunnel manager in the fa-ctx context:
[local]Redback>show tunnel client mobile-ip context fa-ctx Tunnel client information summary --------------------------------------------------------- Client Name : mobile-ip (client-id 2) Context Name : fa-ctx IPIP Tunnel Count : 0 GRE Tunnel Count : 0 Register State : Registered Restart State : Alive
The following example shows how to display detailed information tunnel information about all dynamic tunnel clients that are registered with the tunnel manager in all contexts:
[local]Redback>show tunnel client detail Tunnel client detailed information --------------------------------------------------------- Client Name : mobile-ip (client-id 2) Context Name : local IPIP Tunnel Count : 0 GRE Tunnel Count : 0 Register State : Registered Restart State : Alive Counters Registration requests received : 1 Deregistration requests received : 0 Reregistration requests received : 0 Tunnel add requests received : 0 Tunnel delete requests received : 0 Tunnel modify requests received : 0 Tunnel verify requests received : 0 Tunnel registration responses sent : 0 Client information responses sent : 0 Tunnel verification responses sent : 0 Failed to get state - no client : 0 Invalid config requests received : 0 Reg info req rcvd no client : 0 Client free fail bad client id : 0 Client add fail-bad client id : 0 Client add fail-no memory : 0 Client add fail-due to tree insert : 0 Client add fail-no id available : 0 Client add fail-duplicate insert : 0 Reg resp not sent not registered : 0 Reg resp not sent no memory : 0 Client info not sent-not registered : 0 Client info not sent-no memory : 0 Client IPC xmit queue count : 0 --------------------------------------------------------- Client Name : mobile-ip (client-id 2) Context Name : fa-ctx IPIP Tunnel Count : 0 GRE Tunnel Count : 0 Register State : Registered Restart State : Alive Counters Registration requests received : 1 Deregistration requests received : 0 Reregistration requests received : 0 Tunnel add requests received : 0 Tunnel delete requests received : 0 Tunnel modify requests received : 0 Tunnel verify requests received : 0 Tunnel registration responses sent : 0 Client information responses sent : 0 Tunnel verification responses sent : 0 Failed to get state - no client : 0 Invalid config requests received : 0 Reg info req rcvd no client : 0 Client free fail bad client id : 0 Client add fail-bad client id : 0 Client add fail-no memory : 0 Client add fail-due to tree insert : 0 Client add fail-no id available : 0 Client add fail-duplicate insert : 0 Reg resp not sent not registered : 0 Reg resp not sent no memory : 0 Client info not sent-not registered : 0 Client info not sent-no memory : 0 Client IPC xmit queue count : 0
show udp {sockets | statistics}
Displays User Datagram Protocol (UDP) socket and statistical information.
all modes
sockets |
Displays UDP socket information. |
statistics |
Displays UDP statistics. |
None
Use the show udp command to display UDP socket and statistical information.
The following example displays output when the statistics keyword is specified:
[local]Redback>show udp statistics
udp: 95808 datagrams received 0 with incomplete header 0 with bad data length field 0 with bad checksum 875 dropped due to no socket 94931 broadcast/multicast datagrams dropped due to no socket 0 dropped due to full socket buffers 2 delivered 875 PCB hash misses 875 datagrams output
The following example displays output when the sockets keyword is specified:
[local]Redback>show udp sockets
Active Internet connections (including servers) PCB Recv-Q Send-Q Local Address Foreign Address f07cbb80 0 0 127.0.0.1.64721 *.* vc f07cb958 0 0 127.0.0.1.64741 *.* f07cb8a0 0 0 127.0.0.1.64746 *.* f07cbcf0 0 0 127.0.0.1.64773 *.* f07cb730 0 0 127.0.0.1.64790 *.* f07cbc38 0 0 127.0.0.1.64876 *.* f07cba6c 0 0 127.0.0.1.123 *.* f07cb7e8 0 0 127.0.0.1.64914 *.* f07cb78c 0 0 127.0.0.1.64915 *.* f07cb6d4 0 0 127.0.0.1.64917 *.* f07cb678 0 0 127.0.0.1.64918 *.* f07cbbdc 0 0 127.0.0.1.64919 *.* f07cbe60 0 0 127.0.0.1.64920 *.* f07cbf18 0 0 127.0.0.1.64921 *.* f07cbf74 0 0 127.0.0.1.64922 *.* f07cbebc 0 0 127.0.0.1.6000 *.*
show version
Displays the current version of the software running on the system.
This command has no keywords or arguments.
None
Use the show version command to display the current version of the software running on the system.
For the SmartEdge 100 router with one or both ATM OC media interface cards (MICs), the command output includes, at or near its end, several lines dedicated to the MICs.
The following example displays output from the show version command:
[local]Redback>show version
Redback Networks SmartEdge OS Version SEOS-5.0.5-Release Built by sysbuild@@lx-lsf159Fri Jan 27 01:30:02 PST 2006 Copyright (C) 1998-2006, Redback Networks Inc. All rights reserved. System Bootstrap version is PowerPC,1.0b1267 Installed minikernel version is 20 Router Up Time - 22 hours 1 minute 18 secs
The following example displays output from the show version command for a SmartEdge 100 router with one ATM OC3 MIC installed in slot 2. The MIC manufacturing information in the next line gives the Redback copyright notice:
[local]Redback#show version Redback Networks SmartEdge OS Version SEOS-7.0.0.0-Release Built by sysbuildd@lx-lsf401 Wed Nov 22 10:05:57 PST 2006 Copyright (C) 1998-2006,Redback Networks Inc. All rights reserved. System Bootstrap version is PowerPC,rev2.0.1.2 Installed minikernel version is 2.6 ... Linecard 2 MIC _mic_ sarc Version SEOS-7.0.0.0-Release Built by sysbuildd@lx-lsf401 Wed Nov 22 10:21:45 PST 2006 Copyright (C) 1998-2006,Redback Networks Inc. All rights reserved. Router Up Time - 3 minutes 42 secs
show vpls [bridge-name] [detail]
Displays Virtual Private LAN Services (VPLS)-enabled bridge information.
all modes
bridge-name |
Optional. Name of the VPLS-enabled bridge instance name. Displays information for the specified bridge instance. |
detail |
Optional. Displays detailed information. |
None
Use the show vpls command to display VPLS-enabled bridge information.
The following example displays output from the show vpls command:
[local]Redback>show vpls
VPLS Bridge Pseudo-wire ID Peers(Up) State BridgeName 1 1(1 ) Enable
The following example displays output from the show vpls detail command:
[local]Redback>show vpls detail VPLS instance name : vplsA Context name : local Admin state : Enable Bridge identifier : 0x1 Context identifier : 0x40080001 Default PW-identifier : <none> Number of peers : 1 (Up:1, hub:1, spoke:0) Number of standby peers : 1 (local PE-rs) 0 (local MTU-s)
To display Virtual Private LAN Services (VPLS) peer information for a specific bridge, the syntax is:
show vpls bridge-name peer [ip-addr | profile prof-name | pw-id pw-num | pw-name pw-name] [detail]
To display VPLS peer information for all bridges, the syntax is:
show vpls peer ip-addr {pw-id pw-num | pw-name pw-name} [detail]
Displays VPLS peer information.
all modes
bridge-name |
VPLS-enabled bridge instance name. Displays information for the VPLS peers on the specified bridge instance. |
ip-addr |
VPLS peer IP address in the form A.B.C.D. Displays information for the specified VPLS peer. Optional when displaying peer information for a specific bridge. |
profile prof-name |
VPLS profile name. Displays information for the VPLS peers in the specified VPLS profile. Optional when displaying peer information for a specific bridge. |
pw-id pw-num |
Pseudo-wire number. Displays information for the VPLS peers that use the specified pseudo-wire number. Optional when displaying peer information for a specific bridge. |
pw-name pw-name |
Pseudo-wire name. Displays information for the VPLS peers that use the specified pseudo-wire name. Optional when displaying peer information for a specific bridge. |
detail |
Optional. Displays detailed information. |
None
Use the show vpls peer command to display VPLS peer information.
When the root command is used without any additional syntax, information for all the VPLS peer instances is displayed. If additional syntax is used to match a single VPLS peer instance, then the detailed version of the output is displayed. If additional syntax is used to help filter the set of VPLS peers, then the brief version of the output is displayed.
Table 13 describes the show vpls peer command output fields.
Field |
Description |
---|---|
Admin state |
Computed administrative state for the peer:
|
Bridge id |
System-generated bridge ID. |
Circ cfg changes |
Circuit configuration change count. |
Circ delete cnt |
Circuit delete count. |
Circ error cnt |
Circuit error count. |
Circ up/down cnt |
Circuit up and down count. |
Circuit ID |
Circuit ID, represented as VPLS circuit-id, which is used by a peer in the system. A circuit is allocated for each peer, except standby peers. A standby peer uses the circuit associated with the primary peer on switchover. |
Context id |
Context ID. |
Context name |
Name of the context in which VPLS is configured. |
Last error |
Last error logged by the system:
|
MAC flush received |
MAC flush received count. |
MAC flush sent |
MAC flush sent count. |
Oper State/State |
Operational state of the peer:
|
PE local mode |
Local mode of operation for the neighbor connection:
|
PE peering Type/Type |
VPLS peering type:
This field describes the configuration, and not necessarily the operation state. |
Peer config changes |
Peer configuration change count. |
Peer flags |
Run-time bit flags maintained by a peer to capture the state as it understands it:
|
Peer ID |
VPLS peer ID, which is the neighbor IP address. |
Peer proc restarts |
Peer process restart count. |
Peer reset cnt |
Peer reset count. |
Peer restart cnt |
Peer restart count. |
Peer state changes |
Peer state change count. |
Peer up/down cnt |
Peer up and down count. |
Prev event |
Previous peer flag event:
|
Prev state |
Previous operational state:
|
Primary PE |
Primary neighbor’s IP address. |
Primary PE state |
Primary neighbor’s operational state. For more information about the values for this field, see the Prev State field. |
Profile name |
VPLS profile name. |
Pseudo-wire ID |
Pseudo-wire ID. The ID can be the pseudo-wire name or number. |
PW encap type |
Pseudo-wire encapsulation type:
|
PW error cnt |
Pseudo-wire error count. |
PW exp bits |
Pseudo-wire EXP bits. |
PW flags |
Run-time bit flags maintained by a peer for a pseudo-wire:
|
PW In label |
MPLS label used for packets received over the pseudo-wire. |
PW local MTU |
Pseudo-wire local MTU. |
PW Out label |
MPLS label used for packets transmitted over the pseudo-wire. |
PW remote MTU |
Pseudo-wire remote MTU. |
PW restart cnt |
Pseudo-wire restart count. |
PW state |
Pseudo-wire state:
|
PW up/down cnt |
Pseudo-wire up and down count. |
Standby PE |
Standby neighbor’s IP address. |
Standby PE state |
Standby neighbor’s operational state. For more information about the values for this field, see the Prev State field. |
VPLS Bridge |
VPLS bridge name. |
VPLS peer |
VPLS peer is uniquely identified by the following three values:
|
(1) If the process
restart occurred when a standby peer was operational, then the states
for the primary and standby peers are recovered.
The following example displays output from the show vpls peer command:
[local]Redback>show vpls peer VPLS Bridge Peer ID Pseudo-wire ID Circuit ID Type State corpA 22.22.22.22 100 VPLS 3 Hub Up corpA 33.33.33.33 100 VPLS 4 Hub Up corpA 55.55.55.55 100 VPLS 6 Sp Up
The following example displays output from the show vpls peer command:
[local]Redback>show vpls peer detail VPLS peer (bridge/ip:pwid): vplsA/22.22.22.22:10 Oper State : Up Context name : local Admin State : Enable Circuit id : VPLS 3 Peer Flags : active, pw-up Bridge id : 0x1 Context id : 0x40080001 PE peering type : Hub PE local mode : PE-rs Prev state : Down Profile name : forvplsA Prev event : pw-up Last error : no error PW state : Up, Active PW up/down cnt : 1 PW error cn : 0 PW restart cnt : 1 PW In label : 131072 PW encap type : Ethernet PW Out label : 131072 PW Exp bits : 0x0 PW local MTU : 1500 PW remote MTU : 1500 PW flags : in-rib, in-lblmap, in-ldp, from-ldp, from-cfg, ism-up, peer-up
The following example displays output from the show vpls peer command when primary and standby neighbors are configured:
[local]Redback>show vpls peer VPLS Bridge Peer ID Pseudo-wire ID Circuit ID Type State corpA-MTU 11.11.11.11 100 VPLS 3 Sp Pri Up corpA-MTU 33.33.33.33 100 VPLS 3 Sp Sby Stby
The following example displays output from the show vpls peer detail command when primary and standby neighbors are configured:
[local]Redback>show vpls peer detail VPLS peer (bridge/ip:pwid): corpA-MTU/11.11.11.11:100 Oper State : Up Context name : local Admin State : Enable Circuit id : VPLS 1 Peer Flags : pri, active, pw-up Bridge id : 0x1 Context id : 0x40080001 PE peering type : Spoke PE local mode : MTU-s Standby PE : 33.33.33.33 Standby PE state : Stby Prev state : Down Profile name : p1 Prev event : cct-cfg-change Last error : no error Peer up/down cnt : 1 Peer state changes : 2 Peer reset cnt : 0 Peer config changes : 0 Peer restart cnt : 0 Peer proc restarts : 0 MAC flush sent : 0 MAC flush received : 0 Circ up/down cnt : 0 Circ cfg changes : 2 Circ error cnt : 0 Circ delete cnt : 0 PW state : Up, Active PW up/down cnt : 1 PW error cnt : 0 PW restart cnt : 1 PW In label : 131072 PW encap type : Ethernet PW Out label : 131072 PW Exp bits : 0x0 PW local MTU : 1500 PW remote MTU : 1500 PW flags : in-rib, in-lblmap, in-ldp, from-ldp, from-cfg peer-up VPLS peer (bridge/ip:pwid): corpA-MTU/33.33.33.33:100 Oper State : Stby Context name : local Admin State : Enable Circuit id : VPLS 1 Peer Flags : stby, pw-up Bridge id : 0x1 Context id : 0x40080001 PE peering type : Spoke PE local mode : MTU-s Primary PE : 11.11.11.11 Primary PE state : Up Prev state : Down Profile name : p1 Prev event : pw-up Last error : no error Peer up/down cnt : 0 Peer state changes : 2 Peer reset cnt : 0 Peer config changes : 0 Peer restart cnt : 0 Peer proc restarts : 0 MAC flush sent : 0 MAC flush received : 0 Circ up/down cnt : 0 Circ cfg changes : 0 Circ error cnt : 0 Circ delete cnt : 0 PW state : Down, Standby, In-active PW up/down cnt : 1 PW error cnt : 0 PW restart cnt : 1 PW In label : 131073 PW encap type : Ethernet PW Out label : 131072 PW Exp bits : 0x0 PW local MTU : 1500 PW remote MTU : 1500 PW flags : in-lblmap, in-ldp, from-ldp, from-cfg peer-up
show vpls profile [prof-name [pe ip-addr]] [detail]
Displays Virtual Private LAN Services (VPLS) profile information.
all modes
prof-name |
Optional. VPLS profile name. Displays information for the specified VPLS profile. |
pe ip-addr |
Optional. VPLS neighbor IP address in the form A.B.C.D. Displays VPLS profile information for the specified VPLS peer. |
detail |
Optional. Displays detailed information. |
None
Use the show vpls profile command to display VPLS profile information.
The following example displays output from the show vpls profile command:
[local]Redback>show vpls profile
VPLS Profile PE ID Bridge Profile Type Peers(Up) test 1.2.1.1 Hub 1 (1) test 1.2.1.2 Hub 1 (1)
The following example displays output from the show vpls profile detail command:
[local]Redback>show vpls profile detail VPLS profile (name/pe-id) : test/1.2.1.1 PE peering type : Hub PE local mode : PE-rs Number of peers : 1 Active peers : 1 Standby for : none Bridge profile : forvplsA Enacp type : Ethernet MAC limit : 16002 Bcast rate-limit : 0 Bcast burst-size : 1 Mcast rate-limit : 1 Mcast burst-size : 0 Unknown rate-limit : 0 Unknown burst-size : 0 Bridge flags : 0x8004
show vrrp [debug | memory | routers [if-name | vrrp-id] | statistics [if-name | vrrp-id]]
Displays Virtual Router Redundancy Protocol (VRRP) information.
all modes
debug |
Optional. Displays debug options and filters. |
memory |
Optional. Displays how much memory has been used. |
routers |
Optional. Displays state information pertaining to virtual routers. |
if-name |
Optional. Interface name. Displays the specified information for only the named interface. |
vrrp-id |
Optional. Virtual router ID. The range of values is 1 to 255. Displays the specified information for only the VRRP ID indicated. |
statistics |
Optional. Displays VRRP statistics. |
When entered without specifying any options, this command displays all VRRP statistics information.
Use the show vrrp command to display VRRP information. Router and statistics information may be limited to virtual routers on a single interface or a single virtual router on a single interface.
The following example displays output from the show vrrp command:
[local]Redback>show vrrp
--- VRRP Virtual Router vrrp1/2 (Backup) --- State : Backup Last Event : Interface Up Priority : 100 Advertise Int : 22 Last Adv Source : 0.0.0.0 Up Time : 5d 05:24:04 Preempt : No Master Down Int : 66 Skew Time (u-sec) : 218750 Auth Type: : None Key Chain : Address List: 1.1.1.1 --- VRRP Virtual Router vrrp1/3 (Backup) --- State : Init Last Event : None Priority : 100 Advertise Int : 1 Last Adv Source : 0.0.0.0 Up Time : N/A Preempt : No Master Down Int : 3 Skew Time (u-sec) : 609375 Auth Type: : None Key Chain : Address List: 2.2.2.2
The following example displays output from the show vrrp statistics command:
[local]Redback>show vrrp statistics
--- VRRP Global Statistics --- Virtual Routers : 3 Interfaces : 1 Packets Sent : 0 Packets Received : 0 Packet Dropped : 0 No Router Errors : 0 Checksum Errors : 0 Version Errors : 0 --- VRRP Virtual Router vrrp1/1 (Backup) --- Master Transitions: 0 Advertisement Recv: 0 Advertisement Sent: 0 Priority 0 Recv : 0 Priority 0 Sent : 0 Bad Type Errors : 0 Wrong Owner Errors: 0 IP TTL Error : 0 Pkt Length Errors : 0 Interval Errors : 0 Address Errors : 0 Auth Type Errors : 0 Auth Mismatchs : 0 Auth Failures : 0 Auth Header Errors: 0 --- VRRP Virtual Router vrrp1/2 (Backup) --- Master Transitions: 0 Advertisement Recv: 0 Advertisement Sent: 0 Priority 0 Recv : 0 Priority 0 Sent : 0 Bad Type Errors : 0 Wrong Owner Errors: 0 IP TTL Error : 0 Pkt Length Errors : 0 Interval Errors : 0 Address Errors : 0 Auth Type Errors : 0 Auth Mismatchs : 0 Auth Failures : 0 Auth Header Errors: 0 --- VRRP Virtual Router vrrp1/3 (Backup) --- Master Transitions: 0 Advertisement Recv: 0 Advertisement Sent: 0 Priority 0 Recv : 0 Priority 0 Sent : 0 Bad Type Errors : 0 Wrong Owner Errors: 0 IP TTL Error : 0 Pkt Length Errors : 0 Interval Errors : 0 Address Errors : 0 Auth Type Errors : 0 Auth Mismatchs : 0 Auth Failures : 0 Auth Header Errors: 0
show xc l2vpn [[slot/port] circuit-id | group {group-name | default} | lg id lg-name-in | ldp} | peer peer-addr| route | static] [detail] | [summary]]
Displays Layer 2 Virtual Private Network (L2VPN) cross-connect information.
all modes
circuit-id |
Optional. Layer 2 (L2) circuit ID. Depending on the type of circuit being cross-connected, the L2 circuit ID takes one of the following constructs:
For Ethernet ports with no 802.1Q PVCs, no circuit descriptor is specified. |
circuit-id |
Optional. Layer 2 (L2) circuit ID. Depending on the type of circuit being cross-connected, the L2 circuit ID takes one of the following constructs:
For Ethernet ports with no 802.1Q PVCs, no circuit descriptor is specified. |
group |
Optional. Displays cross-connection information only for a specific cross-connection group. |
group-name |
Cross-connection group name. |
default |
Displays cross-connection information only for the default cross-connection group. |
lg id lg-name-in |
Specifies the name of an access link group to be cross-connected inbound |
ldp |
Optional. Displays only Label Distribution Protocol (LDP) L2VPN cross-connection information. |
peer peer-addr |
IP address of the remote peer provider edge (PE) router. |
static |
Optional. Displays only static L2VPN cross-connection information. |
route |
Displays L2VPN route information. |
detail |
Optional. Displays detailed L2VPN cross-connection information. When used with the xc-circuit argument, displays detailed L2VPN cross-connection information only for the specified cross-connected circuit. |
summary |
Displays summary L2VPN information. |
None.
Use the show xc l2vpn command to display L2VPN-related information.
The following example displays information about all L2VPN cross-connections that are configured on the current router:
[local]Redback# show xc l2vpn Static L2VPN Circuits L2 Circuit L2 State Peer address Label 10/1 vlan-id 1 Up 1.1.1.2 4097 10/1 vlan-id 2 Up 1.1.1.2 4098 10/1 vlan-id 3 Up 1.1.1.2 4099 10/1 vlan-id 4 Up 1.1.1.2 4100 10/1 vlan-id 5 Up 1.1.1.2 4101 LDP L2VPN Circuits L2 Circuit L2 State Peer address VC Id L-Label State VPLS 0x4000002 Up 83.1.1.1 10 131073 Down VPLS 0x4000003 Up 111.111.111.111 10 131074 Down 4/1 vpi-vci 1 100 Up 111.111.111.111 10000 131075 Down
The following example shows how to display L2VPN route information:
[local]Redback>show xc l2vpn route L2 Circuit XC Circuit Next-hop Uptime 10/1:1023:63/1/2/4099 255/12:2:63/0/1/10 1.1.1.2 01:41:59 10/1:1023:63/1/2/4100 255/12:3:63/0/1/11 1.1.1.2 01:41:59 10/1:1023:63/1/2/4101 255/12:4:63/0/1/12 1.1.1.2 01:41:58 10/1:1023:63/1/2/4102 255/12:5:63/0/1/13 1.1.1.2 01:41:58 10/1:1023:63/1/2/4103 255/12:6:63/0/1/14 1.1.1.2 01:41:37
The following example displays static L2VPN cross-connection information:
[local]RedBack#show xc l2vpn static Static L2VPN Circuits L2 Circuit L2 State Peer address Label 10/1 vlan-id 1 Up 1.1.1.2 4097 10/1 vlan-id 2 Up 1.1.1.2 4098 10/1 vlan-id 3 Up 1.1.1.2 4099 10/1 vlan-id 4 Up 1.1.1.2 4100 10/1 vlan-id 5 Up 1.1.1.2 4101
The following example displays detailed information about the L2VPN cross-connection configured on port 4 of the card installed in slot 1:
[local]Redback>show xc l2vpn 4/1 vpi-vci 1 100 detail LDP L2VPN Circuit 4/1 vpi-vci 1 100 L2 State : Up Peer : 111.111.111.111 VC ID : 10000 XC state : Down Local Label : 131075 Access Circuit : 4/1:1:63/1/2/4098 Remote Label : 131072 L2VPN Circuit : 255/12:785:63/0/1/8 EXP bits : 0 Local Encap : atm-cell Remote Group ID : 0 Remote Encap : Local VC Type : ATM VCC Cell Remote VC Type : ATM VCC Cell Local VC MTU : 4470 Remote VC MTU : 0 XC group : foo Negotiated cbit : no Flags 0x0008014a: delete-sig, in-lblmap, in-ldp, from-cfg :