COMMAND DESCRIPTION     17/190 82-CRA 119 1170/1-V1 Uen C    

Commands: show b

© Ericsson AB 2009–2010. All rights reserved. No part of this document may be reproduced in any form without the written permission of the copyright owner.

Disclaimer

The contents of this document are subject to revision without notice due to continued progress in methodology, design and manufacturing. Ericsson shall have no liability for any error or damage of any kind resulting from the use of this document.

Trademark List

SmartEdge is a registered trademark of Telefonaktiebolaget LM Ericsson.
NetOp is a trademark of Telefonaktiebolaget LM Ericsson.

Contents

1Command Descriptions
1.1show bert
1.2show bfd session
1.3show bgp attribute
1.4show bgp attribute extended-community
1.5show bgp malform
1.6show bgp neighbor
1.7show bgp neighbor flap-statistics
1.8show bgp notification
1.9show bgp peer-group
1.10show bgp reset-log
1.11show bgp route
1.12show bgp route community
1.13show bgp route ext-community route-target
1.14show bgp route flap-statistics
1.15show bgp route inconsistent-as
1.16show bgp route ipv4
1.17show bgp route ipv4 vpn
1.18show bgp route ipv4 vpn summary
1.19show bgp route ipv6 unicast
1.20show bgp route ipv6 vpn
1.21show bgp route labels
1.22show bgp route neighbor
1.23show bgp route regexp
1.24show bgp route sourced
1.25show bgp route summary
1.26show bgp summary
1.27show bindings
1.28show bridge associations
1.29show bridge bindings
1.30show bridge info
1.31show bridge loop-detection
1.32show bridge profile
1.33show bridge statistics
1.34show bridge table
1.35show bridge table mac-entry
1.36show bridge table type
1.37show bulkstats
1.38show bypass


1   Command Descriptions

Commands starting with “show b” are included.

1.1   show bert

For ports on channelized OC-12 traffic cards, the syntax is:

show bert slot/port:ds3-chan-num[:ds1-chan-num]

For channelized ports on DS-3 traffic cards, the syntax is:

show bert slot/port[:ds1-chan-num]

For clear-channel ports on DS-3 or E3 traffic cards, or ports on Asynchronous Transfer Mode (ATM) DS-3 traffic cards, the syntax is:

show bert slot/port

1.1.1   Purpose

Displays Bit Error Rate Tester (BERT) results for an ATM DS-3, clear-channel DS-3, or E3 port, or a DS-1 or clear-channel DS-3 channel.

1.1.2   Command Mode

All modes

1.1.3   Syntax Description

slot

Chassis slot number of the traffic card with the port being tested.

port

Port number being tested.

ds3-chan-num

Optional. DS-3 channel number on the on the channelized OC-12 port being tested. The range of values is 1 to 12.

ds1-chan-num

Optional. DS-1 channel number on the channelized DS-3 channel or port being tested. If omitted, the DS-3 channel must be clear-channel. The range of values is 1 to 28.

1.1.4   Default

Displays results for all channels on the port.

1.1.5   Usage Guidelines

Use the show bert command to display BERT results for a port or channel.

Note:  
The following notes apply to this command:

1.1.6   Examples

The following example displays the BERT output for the channelized OC-12 traffic card in slot 2, port 1, DS-3 channel 1, DS-1 channel 1:

[local]Redback>show bert 2/1:1:1
  BERT stats for port 2/1:1:1
    State              : Enabled
    Pattern            : 1s
    Interval           : 1 minute(s)
    Injected err rate  : None
    Time remaining     : 00:00:40
    Total errors       : 0
    Elapsed sync time  : 00:00:00
    Errors this sync   : 0
    Sync count         : 0

The following example displays the BERT output for the ATM DS-3 traffic card in slot 13, port 3:

[local]Redback>show bert 13/3
BERT stats for port 13/3 
State : Active 
Pattern : 2^15 
Interval : 3 minute(s) 
Injected err rate : 1 in 100 milliseconds 
Time remaining : 00:02:45 
Total errors : 0 
Elapsed sync time : 00:00:15 
Errors this sync : 134 
Sync count : 1

1.2   show bfd session

show bfd session [ip-addr] [detail] [all-context]

1.2.1   Purpose

Displays active Bidirectional Forwarding Detection (BFD) session information for neighbors in the current context.

1.2.2   Command Mode

All modes

1.2.3   Syntax Description

ip-addr

Optional. BFD neighbor IP address in the form A.B.C.D.

detail

Optional. Displays detailed information.

all-context

Optional. Displays BFD session information for all contexts. This option is only valid in the local context.

1.2.4   Default

Active BFD session information for all neighbors is displayed.

1.2.5   Usage Guidelines

Use the show bfd session command to display active BFD session information for neighbors in the current context.

If the optional neighbor IP address is specified, only the session to that neighbor is displayed.

Note:  
By default, most show commands (in any mode) display information for the current context only or, depending on the command syntax, for all contexts. If you are an administrator for the local context, you can insert the optional context ctx-name construct, preceding the show command, to view output for the specified context without entering that context. For more information about using the context ctx-name construct, see the context command description.

Note:  
By appending a space followed by the pipe ( | ) character at the end of a show command, you can filter the output using a set of modifier keywords and arguments. For more information, see Modifying Output of show Commands in Using the CLI.

1.2.6   Examples

The following example displays BFD session information:

[local]Redback>show bfd session
Neighbor    Next-hop      Minimum      Multiplier     State       Constituents
                        Tx/Rx intvl
1.1.1.2     31700004    1000/1000      3              Down        2

The following example displays detailed BFD session information:

[local]Redback>show bfd session detail


BFD Neighbor: 1.1.1.2             BFD interface grid: 0x10000001
  Context id: 0x40080001             Next-hop grid: 0x31700004
  Circuit: 255/11:1023:63/1/2/5
  Configured
   Transmit interval: 1000            Receive interval: 1000
   Multiplier: 3


 Constituents:
  Next-hop grid: 0x34500007
  Circuit: 2/8:1023:63/1/2/28
  Local discriminator: 0x2081a1f     Remote discriminator: 0x2091a20
  State: Down                        Previous State: Up
  Local diag: Neighbour signalled sess down
  Source IP addr: 1.1.1.1            Source UDP port: 49157
  Received
   Transmit interval: 1000            Receive interval: 1000
   Multiplier: 3


  Next-hop grid: 0x34500008
  Circuit: 2/6:1023:63/1/2/22
  Local discriminator: 0x2061a15     Remote discriminator: 0x2071a19
  State: Down                        Previous State: Init
  Local diag: Detection timer expired
  Source IP addr: 1.1.1.1            Source UDP port: 49156
  Received
   Transmit interval: 1000            Receive interval: 1000
   Multiplier: 3

1.3   show bgp attribute

show bgp attribute{as-path | community| nexthop| rrinfo | summary}

1.3.1   Purpose

Displays Border Gateway Protocol (BGP) attribute information.

1.3.2   Command Mode

All modes

1.3.3   Syntax Description

as-path

Displays autonomous system (AS) path information.

community

Displays community information.

nexthop

Displays next-hop information.

rrinfo

Displays route reflector information.

summary

Displays attribute summary information.

1.3.4   Default

None

1.3.5   Usage Guidelines

Use the show bgp attribute command to display BGP attribute information.

Note:  
By default, most show commands (in any mode) display information for the current context only or, depending on the command syntax, for all contexts. If you are an administrator for the local context, you can insert the optional context ctx-name construct, preceding the show command, to view output for the specified context without entering that context. For more information about using the context ctx-name construct, see the context command description.

Note:  
By appending a space followed by the pipe ( | ) character at the end of a show command, you can filter the output using a set of modifier keywords and arguments. For more information, see Modifying Output of show Commands in Using the CLI. For information about troubleshooting BGP, see the L3VPN Troubleshooting document.

Table 1 describes the output fields for the show bgp attribute nexthop command.

Table 1    Field Descriptions for the show bgp attribute nexthop Command

Field

Description

Next Hop

IP address of the next-hop neighbor.

Metric

Metric value used.

Ref-count

Number of routes that use the next-hop attribute.

Context-Id

Context ID number.

Interface-id

Interface ID number.

Table 2 describes the output fields for the show bgp attribute summary command.

Table 2    Field Descriptions for the show bgp attribute summary Command

Field

Description

Entry Type

Attribute type.

Count

Number of times the attribute has been applied.

Memory

Amount, in bytes, of memory used to process the application of attribute for the specified count.

Policy Cache Type

Type of routing policy.

Count

Number times the policy has been applied.

Memory

Amount, in bytes, of memory used to process the application of the routing policy for the specified count.

1.3.6   Examples

The following example displays output from the show bgp attribute as-path command:

[local]Redback>show bgp attribute as-path
RefCount  Aspath
       2  14207 3944 2548 3549 20012
       2  64513 2828 5511 4000 3662 4528
       1  14207 3944 2548 6461 7086
       1  14207 3944 2548 3561 5378 6779
       1  64513 2828 209  4766 9754
       2  64513 2828 6453 8657 1930 1930 3251
       1  64513 2828 1239 2516 2521
       1  14207 3944 2548 701  814

The following example displays output from the show bgp attribute community command:

[local]Redback>show bgp attribute community
Community entries: 3, memory used: 116 bytes


RefCount       Community
14181          11:102
2              11:121
2              no-export

The RefCount field indicates how many attributes use the corresponding community.

The following example displays output from the show bgp attribute nexthop command:

[local]Redback>show bgp attribute nexthop
Next hop entries: 5


Next Hop               Metric     Ref-count    Context-Id  Interface-id
10.255.255.254         0          1            40080001    0
10.100.1.102           39         2            40080001    0
10.11.64.100           0          93378        40080001    10000006
10.100.1.5             25         2            40080001    0
10.100.2.3             30         9            40080001    0

The following example displays output from the show bgp attribute rrinfo command:

[local]Redback>show bgp attribute rrinfo
RRinfo entries: 6, memory used: 196 bytes


RefCount    Originator    Cluster-list
      45    1.1.1.71      0.0.0.11
      12    1.1.1.72      0.0.0.11
       2    1.1.1.74      0.0.0.11
      14    100.1.1.1     0.0.0.11
      133   10.100.5.1    0.0.0.11
      32    10.100.2.3    0.0.0.11 10.100.12.0

The following example displays output from the show bgp attribute summary command:

[local]Redback>show bgp attribute summary
Entry Type          Count     Memory
Attribute           31595    1516560
ASpath              12723     506620
Nexthop                13        364
Community               4        116
Ext Community           0          0
Route Reflection        8        228


Policy Cache Type   Count     Memory
AS-path List        38082    1218624
Community List          4        128
Route Map           43990    1407680
Attributes          16724     535168

1.4   show bgp attribute extended-community

show bgp attribute extended-community

1.4.1   Purpose

Displays Border Gateway Protocol (BGP) attribute information for extended communities.

1.4.2   Command Mode

All modes

1.4.3   Syntax Description

This command has no keywords or arguments.

1.4.4   Default

None

1.4.5   Usage Guidelines

Use the show bgp attribute extended-community command to display BGP attribute information for extended communities.

Note:  
By default, most show commands (in any mode) display information for the current context only or, depending on the command syntax, for all contexts. If you are an administrator for the local context, you can insert the optional context ctx-name construct, preceding the show command, to view output for the specified context without entering that context. For more information about using the context ctx-name construct, see the context command description.

Note:  
By appending a space followed by the pipe ( | ) character at the end of a show command, you can filter the output using a set of modifier keywords and arguments. For more information, see Modifying Output of show Commands in Using the CLI. For information about troubleshooting BGP, see the L3VPN Troubleshooting document.

1.4.6   Examples

The following example displays output from the show bgp attribute extended-community command:

[local]Redback>show bgp attribute extended-community 
Extended community entries: 3, memory used: 132 bytes


RefCount  Extended community
   21132  RT:4:4 
   21132  RT:6:6 
   21128  RT:5:5 

1.5   show bgp malform

show bgp malform {messages [keepalive | notification | open | refresh] | update}

1.5.1   Purpose

Displays malformed Border Gateway Protocol (BGP) messages for troubleshooting purposes.

1.5.2   Command Mode

All modes

1.5.3   Syntax Description

messages

Displays malformed BGP nonupdate messages.

keepalive

Optional. Displays only malformed keepalive messages.

notification

Optional. Displays only malformed notification messages.

open

Optional. Displays only malformed open messages.

refresh

Optional. Displays only malformed refresh messages.

update

Displays malformed BGP update messages.

1.5.4   Default

None

1.5.5   Usage Guidelines

Use the show bgp malform command to display malformed BGP messages for troubleshooting purposes.

Note:  
By default, most show commands (in any mode) display information for the current context only or, depending on the command syntax, for all contexts. If you are an administrator for the local context, you can insert the optional context ctx-name construct, preceding the show command, to view output for the specified context without entering that context. For more information about using the context ctx-name construct, see the context command description.

Note:  
By appending a space followed by the pipe ( | ) character at the end of a show command, you can filter the output using a set of modifier keywords and arguments. For more information, see Modifying Output of show Commands in Using the CLI. For information about troubleshooting BGP, see the L3VPN Troubleshooting document.

1.5.6   Examples

The following example shows how to enable the display of malformed BGP update messages:

[local]Redback>show bgp malform update

1.6   show bgp neighbor

show bgp neighbor[{ip-addr | ipv6-addr/prefix-length} [malform {messages[keepalive | notification | open | refresh] | update}] [notification] [received] [reset-log] | summary]

1.6.1   Purpose

Displays Border Gateway Protocol (BGP) neighbor status and statistics.

1.6.2   Command Mode

All modes

1.6.3   Syntax Description

ip-addr

Optional. IP address of the neighbor, in the form A.B.C.D.

ipv6-addr/prefix-length

Optional. IPv6 address and prefix length, separated by the slash (/) character. The range of values for the prefix-length argument is 0 to 128.

malform

Optional. Displays either malformed update or nonupdate messages.

messages

Optional. Displays malformed nonupdate messages.

keepalive

Optional. Displays only malformed keepalive messages.

notification

Optional. Displays only malformed notification messages.

open

Optional. Displays only malformed open messages.

refresh

Optional. Displays only malformed refresh messages.

update

Optional. Displays only malformed update messages.

received

Optional. Displays received address information.

reset-log

Optional. Displays how many times the BGP neighbor has been reset and for what reason the neighbor has been reset.

summary

Optional. Displays summary statistics for all BGP neighbors.

1.6.4   Default

When entered with no keywords or arguments, this command displays information for all BGP neighbors.

1.6.5   Usage Guidelines

Use the show bgp neighbor command to display BGP status and statistics for all BGP neighbors, or for a specific BGP neighbor.

Note:  
By default, most show commands (in any mode) display information for the current context only or, depending on the command syntax, for all contexts. If you are an administrator for the local context, you can insert the optional context ctx-name construct, preceding the show command, to view output for the specified context without entering that context. For more information about using the context ctx-name construct, see the context command description.

Note:  
By appending a space followed by the pipe ( | ) character at the end of a show command, you can filter the output using a set of modifier keywords and arguments. For more information, see Modifying Output of show Commands in Using the CLI. For information about troubleshooting BGP, see the L3VPN Troubleshooting document.

1.6.6   Examples

The following example displays sample output from the show bgp neighbor command:

The following example displays information for BGP neighbor with the IP address, 22.22.22.22

[local]Redback>show bgp neighbor 22.22.22.22


BGP neighbor: 22.22.22.22, remote AS: 1, internal link
  Version: 4, router identifier: 22.22.22.22
  State: Established for 00:55:29
  Last read 00:00:53, last send 00:00:37
  Hold time: configured 180, negotiated 180
  Keepalive time: configured 60, negotiated 60
  Local restart timer 120 sec, stale route retain timer 180 sec
  Received restart timer 120 sec, flag 0x0
  Minimum time between advertisement runs: 5 secs
  Source (local) IP address: 23.23.23.23
  Received messages: 59 (1272 bytes), notifications: 0, in queue: 0
  Sent messages: 6235 (2513115 bytes), notifications: 0, out queue: 0

  CapSent: refresh, 4byteAS, unicast, v6vpn, restart
  CapRcvd: refresh, 4byteAS, unicast, v6vpn
           restart (time 120, flags 0x0, unicast, v6vpn)

  Address family: ipv4 unicast
    BGP table version: 0, neighbor version: 0
    Routes: rcvd 0, imported 0, active 0, history 0, dampend 0, sent 0

  Address family: ipv6 vpn
    BGP table version: 72484, neighbor version: 72484
    Route refresh requests: sent 1,  received 1
    Routes: rcvd 1, imported 1, active 2, history 0, dampend 0, sent 24146

The following example displays output from the show bgp neighbor summary command:

[local]Redback>show bgp neighbor summary


BGP router identifier: 100.100.100.101, local AS number: 1
Neighbors Configured: 7, Established: 3

Neighbor                  AS MsgRcvd MsgSent  InQ OutQ Rst  Up/Down State
1.1.1.1                    1      15    2878    0    0   0 00:09:50 Established
  CapSent  : refresh 4byteAS vpn v6vpn restart
  CapRcvd  : refresh 4byteAS unicast vpn v6unicast v6vpn restart
  vpn      : rcvd: 1 imported: 0 active: 1 history: 0 dampened: 0 sent: 20026
  v6vpn    : rcvd: 1 imported: 0 active: 1 history: 0 dampened: 0 sent: 24146

3.1.4.1                    1      72    4994    0    0   0 01:06:01 Established
  CapSent  : refresh 4byteAS unicast vpn v6vpn restart
  CapRcvd  : refresh 4byteAS unicast vpn v6vpn restart
  unicast  : rcvd: 0 imported: 0 active: 0 history: 0 dampened: 0 sent: 0
  vpn      : rcvd: 5 imported: 5 active: 10 history: 0 dampened: 0 sent: 20026
  v6vpn    : rcvd: 0 imported: 0 active: 0 history: 0 dampened: 0 sent: 24146

10.1.0.65                  1       0       0    0    0   0 01:09:19 Connect
  CapSent  : refresh 4byteAS unicast vpn restart

15.5.19.78                 1       0       0    0    0   0 01:09:19 Connect
  CapSent  : refresh 4byteAS unicast vpn restart

22.22.22.22                1      58    6234    0    0   0 00:53:54 Established
  CapSent  : refresh 4byteAS unicast v6vpn restart
  CapRcvd  : refresh 4byteAS unicast v6vpn restart
  unicast  : rcvd: 0 imported: 0 active: 0 history: 0 dampened: 0 sent: 0
  v6vpn    : rcvd: 1 imported: 1 active: 2 history: 0 dampened: 0 sent: 24146

99.99.1.1                  1       0       0    0    0   0 01:09:19 Connect
  CapSent  : refresh 4byteAS unicast vpn restart

100.100.100.100            1       0       0    0    0   0 01:09:19 Connect
  CapSent  : refresh 4byteAS unicast vpn restart


1.7   show bgp neighbor flap-statistics

show bgp neighbor flap-statistics

1.7.1   Purpose

Displays Border Gateway Protocol (BGP) neighbor flap statistics information.

1.7.2   Command Mode

All modes

1.7.3   Syntax Description

This command has no keywords or arguments.

1.7.4   Default

None

1.7.5   Usage Guidelines

Use the show bgp neighbor flap-statistics command to display BGP neighbor flap statistics information.

Note:  
By default, most show commands (in any mode) display information for the current context only or, depending on the command syntax, for all contexts. If you are an administrator for the local context, you can insert the optional context ctx-name construct, preceding the show command, to view output for the specified context without entering that context. For more information about using the context ctx-name construct, see the context command description.

Note:  
By appending a space followed by the pipe ( | ) character at the end of a show command, you can filter the output using a set of modifier keywords and arguments. For more information, see Modifying Output of show Commands in Using the CLI. For information about troubleshooting BGP, see the L3VPN Troubleshooting document

Table 3 describes the output fields for the show bgp neighbor flap-statistics command.

Table 3    Field Descriptions for the show bgp neighbor flap-statistics Command

Field

Description

Neighbor

Flapping peer. The letter d (before a peer’s IP address) indicates that the peer is dampened.

AS

Peer’s autonomous system (AS).

Flap

Number of times the peer has been flapping for the time indicated in the Duration column.

Penalty

The current penalty applied to the session.

Duration

Length of time that the session has been flapping in the current dampening information.

Reuse

Time (in hours:minutes:seconds) after which the session will be allowed to open again.

1.7.6   Examples

The following example displays output from the show bgp neighbor flap-statistics command:

[local]Redback>show bgp neighbor flap-statistics
  Neighbor              AS  Flap  Penalty  Duration    Reuse
d 1.1.1.1              100     5     4164  00:13:39    00:08:35
  3.3.3.3              200     2     1977  00:00:13

1.8   show bgp notification

show bgp notification

1.8.1   Purpose

Displays Border Gateway Protocol (BGP) notification messages for troubleshooting purposes.

1.8.2   Command Mode

All modes

1.8.3   Syntax Description

This command has no keywords or arguments.

1.8.4   Default

None

1.8.5   Usage Guidelines

Use the show bgp notification command to display BGP notification messages for troubleshooting purposes.

Note:  
By default, most show commands (in any mode) display information for the current context only or, depending on the command syntax, for all contexts. If you are an administrator for the local context, you can insert the optional context ctx-name construct, preceding the show command, to view output for the specified context without entering that context. For more information about using the context ctx-name construct, see the context command description.

Note:  
By appending a space followed by the pipe ( | ) character at the end of a show command, you can filter the output using a set of modifier keywords and arguments. For more information, see Modifying Output of show Commands in Using the CLI. For information about troubleshooting BGP, see the L3VPN Troubleshooting document.

1.8.6   Examples

The following example displays BGP notification messages:

[local]Redback>show bgp notification 
Dump notification messaged logged:
Nov 9 00:36:03 notification msg received (nbr 192.168.3.7, 21 bytes, repeated 0 times, code 4/0 
(hold time expired) - ffff ffff ffff ffff ffff ffff ffff ffff 0015 0304 00
Nov 9 00:36:23 notification msg received (nbr 192.168.41.7, 21 bytes, repeated 0 times, code 4/0 
(hold time expired) - ffff ffff ffff ffff ffff ffff ffff ffff 0015 0304 00

1.9   show bgp peer-group

show bgp peer-group {group-name [member {ipv4 {multicast | unicast} | session}] | summary}

1.9.1   Purpose

Displays information about configured Border Gateway Protocol (BGP) peer groups.

1.9.2   Command Mode

All modes

1.9.3   Syntax Description

group-name

Peer group name.

member

Optional. Displays address family information for the specified peer group.

ipv4

Specifies standard IP Version 4 (IPv4) address prefixes.

multicast

Displays information for multicast address families associated with the peer group.

unicast

Displays information for unicast address families associated with the peer group.

session

Displays BGP session information for the specified peer group.

summary

Displays a summarized set of information for all configured BGP peer groups.

1.9.4   Default

None

1.9.5   Usage Guidelines

Use the show bgp peer-group command to display information about configured BGP peer groups.

Note:  
By default, most show commands (in any mode) display information for the current context only or, depending on the command syntax, for all contexts. If you are an administrator for the local context, you can insert the optional context ctx-name construct, preceding the show command, to view output for the specified context without entering that context. For more information about using the context ctx-name construct, see the context command description.

Note:  
By appending a space followed by the pipe ( | ) character at the end of a show command, you can filter the output using a set of modifier keywords and arguments. For more information, see Modifying Output of show Commands in Using the CLI. For information about troubleshooting BGP, see the L3VPN Troubleshooting document.

1.9.6   Examples

The following example displays output from the show bgp peer-group command:

[local]Redback>show bgp peer-group bgp1
BGP peer-group: bgp1, external link
  Version: 4, router identifier: 0.0.0.0
  Description: external BGP group 1
  Hold time: configured 180, negotiated 0
  Keepalive time: configured 60, negotiated 0
  Local restart timer 120 sec, stale route retain timer 180 sec
  Received restart timer 0 sec, flag 0x0
  Number of hops external BGP neighbor may be away: 1
  Minimum time between advertisement runs: 30 secs
  Source (local) IP address: 0.0.0.0

  Fast reset timer 1234 msecs
   Interface name: to-2/1      State: DOWN
   Interface name: to-mardi    State: DOWN
   Interface name: to-onze     State: UP


  Address family: ipv4 unicast
    BGP table version: 1394616, neighbor version: 0
    Messages: formatted 0, replicated 0
    Prefixes: advertised 0, accepted 0, active 0


  Address family: ipv4 multicast
    BGP table version: 0, neighbor version: 0
    Messages: formatted 0, replicated 0
    Prefixes: advertised 0, accepted 0, active 0

The following example displays BGP peer group summary information:

[local]Redback>show bgp peer-group summary
BGP router identifier: 7.7.7.2, local AS number: 64173
Peer-group Configured: 1 (internal 0, external 1)


Peer-group Name                         Type           
full-routes                             external       

The following example displays BGP peer group member information:

[local]Redback>show bgp peer-group full-routes member 
BGP peer-group: full-routes, external link


Neighbor          AS   MsgRcvd  MsgSent  TblVer  InQ  OutQ Rst  Up/Down   PfxRcvd/Sent
10.13.49.172   64172    200645  253642   287452  0    0    12   00:03:46  0      92248
155.53.1.235   14207      5589   66910   287452  0    0     1   02:41:21  92242  92248

1.10   show bgp reset-log

show bgp reset-log

1.10.1   Purpose

Displays Border Gateway Protocol (BGP) neighbor reset information for troubleshooting purposes.

1.10.2   Command Mode

All modes

1.10.3   Syntax Description

This command has no keywords or arguments.

1.10.4   Default

None

1.10.5   Usage Guidelines

Use the show bgp reset-log command to display information about BGP neighbor resets for troubleshooting purposes.

Note:  
By default, most show commands (in any mode) display information for the current context only or, depending on the command syntax, for all contexts. If you are an administrator for the local context, you can insert the optional context ctx-name construct, preceding the show command, to view output for the specified context without entering that context. For more information about using the context ctx-name construct, see the context command description.

Note:  
By appending a space followed by the pipe ( | ) character at the end of a show command, you can filter the output using a set of modifier keywords and arguments. For more information, see Modifying Output of show Commands in Using the CLI. For information about troubleshooting BGP, see the L3VPN Troubleshooting document.

1.10.6   Examples

The following example displays output from the show bgp reset-log command:

[local]Redback>show bgp reset-log
Dump neighbor reset logs:
Neighbor              StartTime          EndTime   Count  Reason
192.168.3.7      Nov 9 00:36:03   Nov 9 00:36:03       1  Remote/TCP close
192.168.41.7     Nov 9 00:36:23   Nov 9 00:36:23       1  Remote/TCP close
192.168.3.7      Nov 9 01:21:35   Nov 9 01:21:35       1  User action

1.11   show bgp route

show bgp route [ip-addr[/prefix-length]] [longer-prefixes]

1.11.1   Purpose

Displays Border Gateway Protocol (BGP) route information from the BGP routing table.

1.11.2   Command Mode

All modes

1.11.3   Syntax Description

ip-addr

Optional. IP address, in the form A.B.C.D.

prefix-length

Optional. Prefix length. The range of values is 0 to 32.

longer-prefixes

Optional. Available only when the /prefix-length construct is used. Displays routes sent to and from the specified prefix and also displays more specific routes.

1.11.4   Default

When entered without any keywords or arguments, this command displays information for all BGP routes.

1.11.5   Usage Guidelines

Use the show bgp route command to display BGP route information from the BGP routing table.

Note:  
By default, most show commands (in any mode) display information for the current context only or, depending on the command syntax, for all contexts. If you are an administrator for the local context, you can insert the optional context ctx-name construct, preceding the show command, to view output for the specified context without entering that context. For more information about using the context ctx-name construct, see the context command description.

Note:  
By appending a space followed by the pipe ( | ) character at the end of a show command, you can filter the output using a set of modifier keywords and arguments. For more information, see Modifying Output of show Commands in Using the CLI. For information about troubleshooting BGP, see the L3VPN Troubleshooting document.

1.11.6   Examples

The following example displays output from the show bgp route command:

[local]Redback>show bgp route
Address Family: ipv4 unicast
BGP table version is 292821, local router ID is 192.168.41.100
Status codes: d damped, h history, > best, i internal
Origin codes: i - IGP, e - EGP, ? - incomplete


  Network            Next Hop          Metric  LocPrf  Weight Path
  1.0.0.0/8          155.53.0.1             0     100     100 14207 3944 7777 i
  1.2.3.4/32         192.168.41.7           0     100     100 64173 ?
I 2.0.0.0/8          155.53.0.1           200     100     100 14207 3944 7777 i
                     155.53.0.1             0     100     100 14207 3944 7777 i
  2.1.0.0/16         192.168.41.7           0     100     100 64173 100 ?
  2.3.0.0/16         192.168.41.7           0     100     100 64173 100 ?
I 3.0.0.0/8          155.53.0.1           200     100     100 14207 3944 2914 701 80 i
                     155.53.0.1             0     100     100 14207 3944 2914 701 80 i
  3.18.135.0/24      155.53.0.1             0     100     100 14207 64513 2828 2828 2828 2828 7018 ?
I                    155.53.1.236         200     100     100 64513 2828 2828 2828 2828 7018 ?
I 4.0.0.0/8          155.53.0.1           200     100     100 14207 3944 2914 1 i
                     155.53.0.1             0     100     100 14207 3944 2914 1 i
  4.2.1.1/32         192.168.41.7           0     100     100 64173 100 ?
I 4.3.24.3/32        155.53.0.1           200     100     100 14207 3944 7777 i
                     155.53.0.1             0     100     100 14207 3944 7777 i
I 4.21.238.51/32     155.53.0.1           200     100     100 14207 3944 7777 i
                     155.53.0.1             0     100     100 14207 3944 7777 i
I 4.22.124.174/31    155.53.0.1           200     100     100 14207 3944 7777 i
                     155.53.0.1             0     100     100 14207 3944 7777 i
I 4.22.124.176/32    155.53.0.1           200     100     100 14207 3944 7777 i
                     155.53.0.1             0     100     100 14207 3944 7777 i
I 4.22.124.197/32    155.53.0.1           200     100     100 14207 3944 7777 i
                     155.53.0.1             0     100     100 14207 3944 7777 i

1.12   show bgp route community

show bgp route community {community-num | as:nn | local-as | no-advertise | no-export}

1.12.1   Purpose

Displays Border Gateway Protocol (BGP) route community information.

1.12.2   Command Mode

All modes

1.12.3   Syntax Description

community-num

Community number in decimal format. The range of values is 0 to 4,294,967,295.

as:nn

Autonomous system number (ASN) where aa is the ASN and nn is a 2-byte number.

local-as

Displays routes for the local autonomous system (AS).

no-advertise

Displays routes that are not advertised to internal BGP (iBGP) or external BGP (eBGP) peers.

no-export

Displays routes that are sent only to iBGP peers.

1.12.4   Default

When entered without any keywords or arguments, this command displays all route community information.

1.12.5   Usage Guidelines

Use the show bgp route community command to display BGP route community information.

Note:  
By default, most show commands (in any mode) display information for the current context only or, depending on the command syntax, for all contexts. If you are an administrator for the local context, you can insert the optional context ctx-name construct, preceding the show command, to view output for the specified context without entering that context. For more information about using the context ctx-name construct, see the context command description.

Note:  
By appending a space followed by the pipe ( | ) character at the end of a show command, you can filter the output using a set of modifier keywords and arguments. For more information, see Modifying Output of show Commands in Using the CLI. For information about troubleshooting BGP, see the L3VPN Troubleshooting document.

1.12.6   Examples

The following example displays routes matching the BGP community, 2914:420:

[local]Redback>show bgp route community 2914:420
Address Family: ipv4 unicast

BGP table version is 292841, local router ID is 192.168.41.100

Status codes: d damped, h history, > best, i internal

Origin codes: i - IGP, e - EGP, ? - incomplete



  Network            Next Hop       Metric  LocPrf  Weight Path

  3.0.0.0/8          155.53.0.1          0     100     100 14207 3944 2914 701 80 i

i 4.0.0.0/8          155.53.0.1        200     100     100 14207 3944 2914 1 i

                     155.53.0.1          0     100     100 14207 3944 2914 1 i

i 6.0.0.0/20         155.53.0.1        200     100     100 14207 3944 2914 3549 i

                     155.53.0.1          0     100     100 14207 3944 2914 3549 i

i 6.1.0.0/16         155.53.0.1        200     100     100 14207 3944 2914 7170 1455 i

                     155.53.0.1          0     100     100 14207 3944 2914 7170 1455 i

i 6.3.0.0/18         155.53.0.1        200     100     100 14207 3944 2914 7170 1455 i

The following example displays routes matching the BGP community, 7777:7777:

[local]Redback>show bgp route community 7777:7777
Address Family: ipv4 unicast

BGP table version is 292862, local router ID is 192.168.41.100

Status codes: d damped, h history, > best, i internal

Origin codes: i - IGP, e - EGP, ? - incomplete



  Network            Next Hop          Metric  LocPrf  Weight Path

  1.0.0.0/8          155.53.0.1             0     100     100 14207 3944 7777 i

i 2.0.0.0/8          155.53.0.1           200     100     100 14207 3944 7777 i

                     155.53.0.1             0     100     100 14207 3944 7777 i

i 5.0.0.0/8          155.53.0.1           200     100     100 14207 3944 7777 i

                     155.53.0.1             0     100     100 14207 3944 7777 i

i 7.0.0.0/8          155.53.0.1           200     100     100 14207 3944 7777 i

                     155.53.0.1             0     100     100 14207 3944 7777 i

i 23.0.0.0/8         155.53.0.1           200     100     100 14207 3944 7777 i

                     155.53.0.1             0     100     100 14207 3944 7777 i

i 27.0.0.0/8         155.53.0.1           200     100     100 14207 3944 7777 i

                     155.53.0.1             0     100     100 14207 3944 7777 i

i 36.0.0.0/8         155.53.0.1           200     100     100 14207 3944 7777 i

                     155.53.0.1             0     100     100 14207 3944 7777 i

1.13   show bgp route ext-community route-target

show bgp route ext-community route-target ext-com

1.13.1   Purpose

Displays Border Gateway Protocol (BGP) routes for a specific route target extended community.

1.13.2   Command Mode

All modes

1.13.3   Syntax Description

ext-com

Route target extended community value that is added to the export target list. The route target extended community value can be expressed in either of the following formats:


  • asn:nnnn, where asn is the autonomous system number and nnnn is a 32-bit integer.

  • ip-addr:nn, where ip-addr is the IP address in the form A.B.C.D and nn is a 16-bit integer.

1.13.4   Default

None

1.13.5   Usage Guidelines

Use the show bgp route ext-community route-target command to display BGP routes for a specific route target extended community.

Note:  
By default, most show commands (in any mode) display information for the current context only or, depending on the command syntax, for all contexts. If you are an administrator for the local context, you can insert the optional context ctx-name construct, preceding the show command, to view output for the specified context without entering that context. For more information about using the context ctx-name construct, see the context command description.

Note:  
By appending a space followed by the pipe ( | ) character at the end of a show command, you can filter the output using a set of modifier keywords and arguments. For more information, see Modifying Output of show Commands in Using the CLI. For information about troubleshooting BGP, see the L3VPN Troubleshooting document.

1.13.6   Examples

The following example displays the BGP routes for the route target extended community, 2:2:

[local]Redback>show bgp route ext-community route-target 2:2
Address Family: ipv4 unicast

BGP table version is 4, local router ID is 2.2.2.2

Status codes: d damped, h history, > best, i internal

Origin codes: i - IGP, e - EGP, ? - incomplete



VPN RD: 2:2

   Network            Next Hop          Metric  LocPrf  Weight Path

>i 55.55.55.55/32     1.1.1.100            101     100     100 ?

>i 77.1.1.0/24        1.1.1.100              0     100     100 ?

1.14   show bgp route flap-statistics

show bgp route flap-statistics [dampened-path | external | internal]

1.14.1   Purpose

Displays Border Gateway Protocol (BGP) route-flap statistics accounting information.

1.14.2   Command Mode

All modes

1.14.3   Syntax Description

dampened-path

Optional. Displays only BGP routes suppressed due to dampening.

external

Optional. Displays only route-flap statistics for external BGP (eBGP) routes.

internal

Optional. Displays only route-flap statistics for internal BGP (iBGP) routes.

1.14.4   Default

None

1.14.5   Usage Guidelines

Use the show bgp route flap-statistics command to display BGP route-flap statistics accounting information.

Note:  
By default, most show commands (in any mode) display information for the current context only or, depending on the command syntax, for all contexts. If you are an administrator for the local context, you can insert the optional context ctx-name construct, preceding the show command, to view output for the specified context without entering that context. For more information about using the context ctx-name construct, see the context command description.

Note:  
By appending a space followed by the pipe ( | ) character at the end of a show command, you can filter the output using a set of modifier keywords and arguments. For more information, see Modifying Output of show Commands in Using the CLI. For information about troubleshooting BGP, see the L3VPN Troubleshooting document.

1.14.6   Examples

The following example displays output from the show bgp route flap-statistics command:

[local]Redback>show bgp route flap-statistics
Address Family: ipv4 unicast

BGP table version is 418695, local router ID is 192.168.4.100

Status codes: d damped, h history, > best, i internal

Origin codes: i - IGP, e - EGP, ? - incomplete



   Network          From          Flaps Penalty Duration Reuse  Path

i  15.252.0.0/18    10.12.208.81  1     500     00:00:01        14207 3944   6461 7018 71

i  15.252.64.0/20   10.12.208.81  1     500     00:00:01        14207 3944   6461 7018 71

>i 192.6.41.0/24    10.12.208.72  1     500     00:00:00        14207 3944   6461 701 71

i                   10.12.208.81  1     500     00:00:01        14207 3944   6461 701 71

>i 195.82.32.0/19   10.12.208.72  1     1000    00:00:05        14207 3944   6461 9126 8375

i                   10.12.208.81  1     500     00:00:01        14207 3944   6461 9126 8375

hi 198.235.184.0/24 10.12.208.72  1     1000    00:00:00        14207 64513  2828 2828 2828 2828 701 6539 
549 hi              10.12.208.81  1     992     00:00:10        64513 2828   2828 
                                                                2828 2828 701 6539 549 ........

h 130.235.0.0/16    192.168.41.7  6     2224    00:16:59        64173 14207  3944 6461 286 2603 1653 2846 
2846 
h 130.235.56.0/21   192.168.41.7  4     1129    00:20:01        64173 14207  64513 2828 2828 2828 2828 209 
286 2603 1653 2846 
h 130.235.184.0/21  192.168.41.7  4     1129    00:20:01        64173 14207  64513 2828 2828 2828 2828 209 
286 2603 1653 2846

  134.114.0.0/16    192.168.41.7  2     419     00:19:10        64173 14207  3944 6461 701 3908 2900

  144.173.0.0/16    192.168.41.7  2     648     00:09:34        64173 14207  3944 6461 786

h  156.70.0.0/16    192.168.41.7  1     428     00:18:17        64173 14207  3944 6461 1239 5676

  159.226.0.0/16    192.168.41.7  4     988     00:17:48        64173 14207  3944 6461 5727 7497

h  160.8.0.0/16     192.168.41.7  8     1183    01:15:52        64173 14207  3944 6461 1239 5511 2874

d  209.211.0.0/22   192.168.41.7  7     1524    00:55:38        64173 14207  3944 6461 209

The following example displays output from the show bgp route flap-statistics dampened-path command:

[local]Redback>show bgp route flap-statistics dampened-path
Address Family: ipv4 unicast

BGP table version is 418715, local router ID is 192.168.4.100

Status codes: d damped, h history, > best, i internal

Origin codes: i - IGP, e - EGP, ? - incomplete



Network             From             Flaps Penalty   Duration  Reuse     Path

d  209.211.0.0/22   192.168.41.7     7        1524   00:55:38  00:15:45  64173 14207 3944 6461 209

The following example displays output from the show bgp route flap-statistics external command:

[local]Redback>show bgp route flap-statistics external
Address Family: ipv4 unicast

BGP table version is 418994, local router ID is 192.168.4.100

Status codes: d damped, h history, > best, i internal

Origin codes: i - IGP, e - EGP, ? - incomplete



Network             From           Flaps   Penalty    Duration  Reuse    Path

  63.105.82.0/23    192.168.41.7       1       431    00:03:09           64173 14207 64513 2828
                                                                         2828 2828 2828 
                                                                         3356 17074

  63.163.214.0/24   192.168.41.7       1       388    00:05:23           64173 14207 64513 2828 
                                                                         2828 2828 2828 
                                                                         1239 13776

  63.210.250.0/23   192.168.41.7       2       855    00:03:35           64173 14207 64513
                                                                         2828 2828 2828 2828 
                                                                         3356 17074

  63.210.252.0/23   192.168.41.7       2       855    00:03:35           64173 14207 64513 
                                                                         2828 2828 2828 2828 
                                                                         3356 17074

  64.84.0.0/18      192.168.41.7       2       823    00:06:39           64173 14207 3944 
                                                                         6461  1239 10738

h 65.169.76.0/24    192.168.41.7       1       846    00:03:35           64173 14207 64513 
                                                                         2828 2828 2828 2828 
                                                                         1239 22083

h 65.195.55.0/24    192.168.41.7       1       688    00:07:54           64173 14207 64513 
                                                                         2828 2828 2828 2828 701  
                                                                         19623

h 130.235.0.0/16    192.168.41.7       6      1277    00:29:09           64173 14207 3944 
                                                                         6461  286 2603 1653 2846 
                                                                         2846

The following example displays output from the show bgp route flap-statistics internal command. The flap-statistics command (in BGP address family configuration mode) must be enabled to see flap statistics for iBGP peers:

[local]Redback>show bgp route flap-statistics internal
Address Family: ipv4 unicast

BGP table version is 419481, local router ID is 192.168.4.100

Status codes: d damped, h history, > best, i internal

Origin codes: i - IGP, e - EGP, ? - incomplete



   Network            From           Flaps Penalty  Duration Reuse    Path

i  15.252.0.0/18      10.12.208.81       1     500  00:00:01          14207 3944 6461 7018 71

i 15.252.64.0/20      10.12.208.81       1     500  00:00:01          14207 3944 6461 7018 71

>i 192.6.41.0/24      10.12.208.72       1     500  00:00:00          14207 3944 6461 701   71

i                     10.12.208.81       1     500  00:00:01          14207 3944 6461 701   71

>i 195.82.32.0/19     10.12.208.72       1    1000  00:00:05          14207 3944 6461 9126 8375

i                     10.12.208.81       1     500  00:00:01          14207 3944 6461 9126 8375

1.15   show bgp route inconsistent-as

show bgp route inconsistent-as

1.15.1   Purpose

Displays Border Gateway Protocol (BGP) routes sourced from more than one autonomous system (AS).

1.15.2   Command Mode

All modes

1.15.3   Syntax Description

This command has no keywords or arguments.

1.15.4   Default

None

1.15.5   Usage Guidelines

Use the show bgp route inconsistent-as command to display BGP routes sourced from more than one AS.

Note:  
By default, most show commands (in any mode) display information for the current context only or, depending on the command syntax, for all contexts. If you are an administrator for the local context, you can insert the optional context ctx-name construct, preceding the show command, to view output for the specified context without entering that context. For more information about using the context ctx-name construct, see the context command description.

Note:  
By appending a space followed by the pipe ( | ) character at the end of a show command, you can filter the output using a set of modifier keywords and arguments. For more information, see Modifying Output of show Commands in Using the CLI. For information about troubleshooting BGP, see the L3VPN Troubleshooting document.

1.15.6   Examples

The following example displays output from the show bgp route inconsistent-as command:

[local]Redback>show bgp route inconsistent-as
Address Family: ipv4 unicast

BGP table version is 418763, local router ID is 192.168.4.100

Status codes: d damped, h history, > best, i internal

Origin codes: i - IGP, e - EGP, ? - incomplete



Network               Next Hop            Metric  LocPrf   Weight   Path

>i 192.231.3.0/24     155.53.1.235             0     100      100   14207 3944  6461 1 239 5696 10943 i

                      192.168.41.7             0     100      100   64173 14207 3944 6461 1239 5696 
                                                                    10943 i

i                     155.53.1.236             0     100      100   64513 2828  2828 2 828 2828 3561 i

>i 198.148.166.0/24   155.53.1.235             0     100      100   14207 3944  6461 7 01 1673 1322 1335 
                                                                                       8174 18920 i

                      192.168.41.7             0     100      100   64173 14207 3944 6461 701 1673 1322 
                                                                    1335 8174 18920 i

i                     155.53.1.236             0     100      100   64513 2828  2828 2 828 2828 701 703 
                                                                    4716 9999 i

>i 198.203.153.0/24   155.53.1.235             0     100      100   14207 3944  6461 1 239 5696 
                                                                                      10943 i

                      192.168.41.7             0     100      100   64173 14207 3944 6461 1239 5696 
                                                                    10943 i

i                     155.53.1.236             0     100      100   64513 2828  2828  2 

1.16   show bgp route ipv4

show bgp route ipv4 {multicast | unicast}

1.16.1   Purpose

Displays information for Border Gateway Protocol (BGP) multicast or unicast IP Version 4 (IPv4) address prefix-based routes.

1.16.2   Command Mode

All modes

1.16.3   Syntax Description

multicast

Displays information only for multicast routes using IPv4 address prefixes.

unicast

Displays information only for unicast routes using IPv4 address prefixes.

1.16.4   Default

None

1.16.5   Usage Guidelines

Use the show bgp route ipv4 command to display information for BGP multicast or unicast IPv4 address prefix-based routes.

Note:  
By default, most show commands (in any mode) display information for the current context only or, depending on the command syntax, for all contexts. If you are an administrator for the local context, you can insert the optional context ctx-name construct, preceding the show command, to view output for the specified context without entering that context. For more information about using the context ctx-name construct, see the context command description.

Note:  
By appending a space followed by the pipe ( | ) character at the end of a show command, you can filter the output using a set of modifier keywords and arguments. For more information, see Modifying Output of show Commands in Using the CLI. For information about troubleshooting BGP, see the L3VPN Troubleshooting document.

1.16.6   Examples

The following example displays output from the show bgp route ipv4 command:

[local]Redback>show bgp route ipv4
Address Family: ipv4 unicast

BGP table version is 2265175, local router ID is 1.1.1.78

Status codes: d damped, h history, > best, i internal

Origin codes: i - IGP, e - EGP, ? - incomplete



Network          Next Hop       Metric  LocPrf  Weight Path

>i 0.0.0.0/0     10.100.1.1     0       100     100    i

 i 3.0.0.0/8     10.100.1.1     0       100     100    14207 3944 6461 701 80 i

 i                10.100.1.2    0       100     100    14207 3944 6461 701 80 i

 i                10.100.1.5    0       100     100    14207 3944 6461 701 80 i

1.17   show bgp route ipv4 vpn

show bgp route ipv4 vpn [as-path longer count] [rd route-distinguisher] [labels]

1.17.1   Purpose

Displays information for Border Gateway Protocol (BGP) Virtual Private Network IP Version 4 (VPN-IPv4) address prefix-based routes.

1.17.2   Command Mode

All modes

1.17.3   Syntax Description

as-path longer count

Optional. Information for AS-paths equal to or longer than the count value. The range of count values is 1 to 300.

rd route-distinguisher

Optional. Route information for only a specific Virtual Private Network (VPN) context with a route distinguisher of the route-distinguisher value, which can be expressed in either of the following formats:


  • asn:nnnn, where asn is the autonomous system number and nnnn is a 32-bit integer.

  • ip-addr:nn, where ip-addr is the IP address in the form A.B.C.D and nn is a 16-bit integer.

labels

Optional. Displays Multiprotocol Label Switching (MPLS) label information.

1.17.4   Default

This command displays all VPN-IPv4 routes in all VPN contexts.

1.17.5   Usage Guidelines

Use the show bgp route ipv4 vpn command to display information for BGP VPN-IPv4 address prefix-based routes.

Use the rd route-distinguisher construct to display VPN-IPv4 prefixes for just the selected VPN context that matches the route-distinguisher argument.

Note:  
By default, most show commands (in any mode) display information for the current context only or, depending on the command syntax, for all contexts. If you are an administrator for the local context, you can insert the optional context ctx-name construct, preceding the show command, to view output for the specified context without entering that context. For more information about using the context ctx-name construct, see the context command description.

Note:  
By appending a space followed by the pipe ( | ) character at the end of a show command, you can filter the output using a set of modifier keywords and arguments. For more information, see Modifying Output of show Commands in Using the CLI. For information about troubleshooting BGP, see the L3VPN Troubleshooting document.

1.17.6   Examples

The following example displays output from the show bgp route ipv4 vpn command:

[local]Redback>show bgp route ipv4 vpn
Address Family: ipv4 vpn

BGP table version is 0, local router ID is 7.7.7.2

Status codes: d damped, h history, > best, i internal

Origin codes: i - IGP, e - EGP, ? – incomplete



VPN RD: 1.2.3.4:100

   Network            Next Hop          Metric  LocPrf  Weight Path

>  6.3.0.0/18         192.168.41.100         0     100     100 3944 6461 7170 1455 i



VPN RD: 64001:200

   Network            Next Hop          Metric  LocPrf  Weight Path

>  3.0.0.0/8          192.168.3.100          0     100     100 3944 6461 701 80 i

>  10.10.10.10/32     192.168.3.8            0     100     100 100 i

The following example displays only VPN-IPv4 routes from the context with route distinguisher of 1.2.3.4:100:

[local]Redback>show bgp route ipv4 vpn rd 1.2.3.4:100
Address Family: ipv4 vpn

BGP table version is 0, local router ID is 7.7.7.2

Status codes: d damped, h history, > best, i internal

Origin codes: i - IGP, e - EGP, ? – incomplete



VPN RD: 1.2.3.4:100

   Network            Next Hop          Metric  LocPrf  Weight Path

>  6.3.0.0/18         192.168.41.100         0     100     100 3944 6461 7170 1455 i

The following example displays MPLS label information for VPN-IPv4 routes:

[local]Redback>show bgp route ipv4 vpn labels
VPN RD: 2:2

Network            Next Hop            Rcv Label      Alloc Label    

2.1.0.0/16         10.13.49.207        22             589830         

2.3.0.0/16         10.13.49.207        21             589829         

4.2.1.1/32         10.13.49.207        19             589828         



VPN RD: 10.11.12.13:100

Network            Next Hop            Rcv Label      Alloc Label    

2.1.0.0/16         10.13.49.207        22             589830         

2.3.0.0/16         10.13.49.207        21             589829         

4.2.1.1/32         10.13.49.207        19             589828         

6.3.0.0/18         192.168.41.100      nolabel        589826         



VPN RD: 20.21.22.23:200

Network            Next Hop            Rcv Label      Alloc Label    

1.1.1.1/32         0.0.0.0             nolabel        589825

The following example displays MPLS label information only for VPN-IPv4 routes from the context with route distinguisher of 2:2:

[local]Redback>show bgp route ipv4 vpn rd 2:2 labels
VPN RD: 2:2

Network            Next Hop            Rcv Label      Alloc Label    

2.1.0.0/16         10.13.49.207        22             589830         

2.3.0.0/16         10.13.49.207        21             589829         

4.2.1.1/32         10.13.49.207        19             589828 

1.18   show bgp route ipv4 vpn summary

show bgp route ipv4 vpn summary

1.18.1   Purpose

Displays a summary report of Border Gateway Protocol (BGP) Virtual Private Network IP Version 4 (VPN-IPv4) routes in the BGP routing tables for all contexts.

1.18.2   Command Mode

All modes

1.18.3   Syntax Description

This command has no keywords or arguments.

1.18.4   Default

None

1.18.5   Usage Guidelines

Use the show bgp route ipv4 vpn summary command to display a summary report of BGP VPN-IPv4 routes in the BGP routing tables for all contexts.

Note:  
By default, most show commands (in any mode) display information for the current context only or, depending on the command syntax, for all contexts. If you are an administrator for the local context, you can insert the optional context ctx-name construct, preceding the show command, to view output for the specified context without entering that context. For more information about using the context ctx-name construct, see the context command description.

Note:  
By appending a space followed by the pipe ( | ) character at the end of a show command, you can filter the output using a set of modifier keywords and arguments. For more information, see Modifying Output of show Commands in Using the CLI. For information about troubleshooting BGP, see the L3VPN Troubleshooting document.

1.18.6   Examples

The following example displays output from the show bgp route ipv4 vpn summary command:

[local]Redback>show bgp route ipv4 vpn summary
Address Family: ipv4 vpn

BGP router identifier: 2.2.2.2, local AS number: 64000

BGP route table version: 5065742, RIB table version: 5065742

Neighbors Configured: 1, Established: 1

Sourced paths: redistributed: 0, networked: 0, aggregated: 0

Dampening: Disabled



Entry Type      Count          Memory

Network        132281        16201112

Path           132278         3632896



Neighbor          AS  MsgRcvd  MsgSent    TblVer  InQ OutQ Rst  Up/Down  Pfx Rcvd/Sent

1.1.1.1        64000   336115      258   5065646    0 0 0 04:06:48 132270      8



Context: 0x40080002  VPN RD: 2:2

Neighbor          AS  MsgRcvd  MsgSent    TblVer  InQ OutQ Rst  Up/Down  Pfx Rcvd/Sent

60.1.2.2         200      251    48388   5065742    0 0   0 04:06:50      2      0



Context: 0x40080003  VPN RD: 3:3

Neighbor          AS  MsgRcvd  MsgSent    TblVer  InQ OutQ Rst  Up/Down  Pfx Rcvd/Sent

60.1.3.2         201      250    85962   5065742    0    0   0 04:06:45    3      0 

1.19   show bgp route ipv6 unicast

show bgp route ipv6 unicast

1.19.1   Purpose

Displays information for Border Gateway Protocol (BGP) unicast IP Version 6 (IPv6) routes.

1.19.2   Command Mode

All modes

1.19.3   Syntax Description

This command has no keywords or arguments.

1.19.4   Default

None

1.19.5   Usage Guidelines

Use the show bgp route ipv6 unicast command to display information for BGP unicast IPv6 routes.

Note:  
By default, most show commands (in any mode) display information for the current context only or, depending on the command syntax, for all contexts. If you are an administrator for the local context, you can insert the optional context ctx-name construct, preceding the show command, to view output for the specified context without entering that context. For more information about using the context ctx-name construct, see the context command description.

Note:  
By appending a space followed by the pipe ( | ) character at the end of a show command, you can filter the output using a set of modifier keywords and arguments. For more information, see Modifying Output of show Commands in Using the CLI. For information about troubleshooting BGP, see the L3VPN Troubleshooting document.

1.19.6   Examples

The following example displays output from the show bgp route ipv6 unicast command:

[local]Redback>show bgp route ipv6 unicast



Address Family: ipv6 unicast

BGP table version is 2, local router ID is 10.12.209.174

Status codes: d damped, h history, > best, i internal

Origin codes: i - IGP, e - EGP, ? - incomplete



   Network            Next Hop                Metric  LocPrf  Weight Path

>  9001::/64          7001::ff                     0     100     100 200 i

>  9002::/64          7001::ff                     0     100     100 200 i

1.20   show bgp route ipv6 vpn

show bgp route ipv6 vpn [as-path | community | ext-community | flap-statistics | inconsistent-as | labels | neighbor | rd | regexp | sourced | summary]

1.20.1   Purpose

Displays information for Border Gateway Protocol (BGP) IP Version 6 (IPv6) VPN routes.

1.20.2   Command Mode

All modes

1.20.3   Syntax Description

as-path

Optional. Displays autonomous system (AS) path information for BGP IPv6 VPN routes.

community

Optional. Displays community information for BGP IPv6 VPN routes.

ext-community

Optional. Displays BGP IPv6 routes for IPv6 VPN route target extended communities.

flap-statistics

Optional. Displays BGP route-flap statistics accounting information for IPv6 routes.

inconsistent-as

Optional. Displays BGP IPv6 VPN routes sourced from more than one autonomous system (AS).

labels

Optional. Displays Multiprotocol Label Switching (MPLS) label information for BGP IPv6 VPN routes

neighbor

Optional. Displays information about IPv6 VPN routes to and from BGP neighbors.

rd

Optional. Displays route information for BGP IPv6 VPN routes that have route distinguishers.

regexp

Optional. Displays BGP IPv6 VPN route communities.

sourced

Optional. Displays BGP IPv6 VPN routes sourced from the local autonomous system (AS).

summary

Optional. Displays summarized information about BGP IPv6 VPN routes.

1.20.4   Default

Enter the show bgp route ipv6 vpn command without any optional arguments to display information about all BGP IPv6 VPN routes currently configured on the system.

1.20.5   Usage Guidelines

Use the show bgp route ipv6 unicast command to display information for BGP IPv6 VPN routes.

Note:  
By default, most show commands (in any mode) display information for the current context only or, depending on the command syntax, for all contexts. If you are an administrator for the local context, you can insert the optional context ctx-name construct, preceding the show command, to view output for the specified context without entering that context. For more information about using the context ctx-name construct, see the context command description.

Note:  
By appending a space followed by the pipe ( | ) character at the end of a show command, you can filter the output using a set of modifier keywords and arguments. For more information, see Modifying Output of show Commands in Using the CLI. For information about troubleshooting BGP, see the L3VPN Troubleshooting document.

1.20.6   Examples

The following example displays output from the show bgp route ipv6 vpn command:

[local]Redback>show bgp route ipv6 vpn

Address Family: ipv6 vpn
Address Family: ipv6 vpn
BGP table version is 72484, local router ID is 100.100.100.101
Status codes: d damped, h history, > best, i internal
Origin codes: i - IGP, e - EGP, ? - incomplete


VPN RD: 10:2222
   Network            Next Hop                Metric  LocPrf  Weight Path
>i 7::/20             22.22.22.22                  0     100     100 ?

VPN RD: 10:3333
   Network            Next Hop                Metric  LocPrf  Weight Path
>i 7::/20             22.22.22.22                  0     100     100 ?

VPN RD: 100:101
   Network            Next Hop                Metric  LocPrf  Weight Path
>i 1000::/64          1.1.1.1                      0     100     100 ?
>  2000::/64          ::                           0     100   32768 ?

VPN RD: 200:1
   Network            Next Hop                Metric  LocPrf  Weight Path
>  1600::1:1:0/120    ::                           0     100   32768 ?
>  1600::2:1:0/120    ::                           0     100   32768 ?
>  1600::3:1:0/120    ::                           0     100   32768 ?
>  1600::4:1:0/120    ::                           0     100   32768 ?
>  1600::5:1:0/120    ::                           0     100   32768 ?
>  1600::6:1:0/120    ::                           0     100   32768 ?
>  1600::7:1:0/120    ::                           0     100   32768 ?
>  1600::8:1:0/120    ::                           0     100   32768 ?
>  1600::9:1:0/120    ::                           0     100   32768 ?
>  1600::10:1:0/120   ::                           0     100   32768 ?
>  1600::11:1:0/120   ::                           0     100   32768 ?
>  1600::12:1:0/120   ::                           0     100   32768 ?
>  1600::13:1:0/120   ::                           0     100   32768 ?
>  1600::14:1:0/120   ::                           0     100   32768 ?
>  1600::15:1:0/120   ::                           0     100   32768 ?
>  1600::16:1:0/120   ::                           0     100   32768 ?
>  1600::17:1:0/120   ::                           0     100   32768 ?
>  1600::18:1:0/120   ::                           0     100   32768 ?
>  1600::19:1:0/120   ::                           0     100   32768 ?
>  1600::20:1:0/120   ::                           0     100   32768 ?
>  1600::21:1:0/120   ::                           0     100   32768 ?
>  1600::22:1:0/120   ::                           0     100   32768 ?
>  1600::23:1:0/120   ::                           0     100   32768 ?
>  1600::24:1:0/120   ::                           0     100   32768 ?
>  1600::25:1:0/120   ::                           0     100   32768 ?
>  1600::26:1:0/120   ::                           0     100   32768 ?
>  1600::27:1:0/120   ::                           0     100   32768 ?
>  1600::28:1:0/120   ::                           0     100   32768 ?
>  1600::29:1:0/120   ::                           0     100   32768 ?
>  1600::30:1:0/120   ::                           0     100   32768 ?
>  1600::31:1:0/120   ::                           0     100   32768 ?
>  1600::32:1:0/120   ::                           0     100   32768 ?
>  1600::33:1:0/120   ::                           0     100   32768 ?
>  1600::34:1:0/120   ::                           0     100   32768 ?
>  1600::35:1:0/120   ::                           0     100   32768 ?
>  1600::36:1:0/120   ::                           0     100   32768 ?
>  1600::37:1:0/120   ::                           0     100   32768 ?
>  1600::38:1:0/120   ::                           0     100   32768 ?
>  1600::39:1:0/120   ::                           0     100   32768 ?
>  1600::40:1:0/120   ::                           0     100   32768 ?
>  1600::41:1:0/120   ::                           0     100   32768 ?
>  1600::42:1:0/120   ::                           0     100   32768 ?
>  1600::43:1:0/120   ::                           0     100   32768 ?
>  1600::44:1:0/120   ::                           0     100   32768 ?
>  1600::45:1:0/120   ::                           0     100   32768 ?
>  1600::46:1:0/120   ::                           0     100   32768 ?
>  1600::47:1:0/120   ::                           0     100   32768 ?
>  1600::48:1:0/120   ::                           0     100   32768 ?
>  1600::49:1:0/120   ::                           0     100   32768 ?
>  1600::50:1:0/120   ::                           0     100   32768 ?
>  1600::51:1:0/120   ::                           0     100   32768 ?
>  1600::52:1:0/120   ::                           0     100   32768 ?
>  1600::53:1:0/120   ::                           0     100   32768 ?
>  1600::54:1:0/120   ::                           0     100   32768 ?
>  1600::55:1:0/120   ::                           0     100   32768 ?
>  1600::56:1:0/120   ::                           0     100   32768 ?
>  1600::57:1:0/120   ::                           0     100   32768 ?
>  1600::58:1:0/120   ::                           0     100   32768 ?
>  1600::59:1:0/120   ::                           0     100   32768 ?
>  1600::60:1:0/120   ::                           0     100   32768 ?
>  1600::61:1:0/120   ::                           0     100   32768 ?
>  1600::62:1:0/120   ::                           0     100   32768 ?
>  1600::63:1:0/120   ::                           0     100   32768 ?
>  1600::64:1:0/120   ::                           0     100   32768 ?
>  1600::65:1:0/120   ::                           0     100   32768 ?
>  1600::66:1:0/120   ::                           0     100   32768 ?
---(more)---

1.21   show bgp route labels

show bgp route labels

1.21.1   Purpose

Displays Multiprotocol Label Switching (MPLS) labels associated with Border Gateway Protocol (BGP) routes.

1.21.2   Command Mode

All modes

1.21.3   Syntax Description

This command has no keywords or arguments.

1.21.4   Default

None

1.21.5   Usage Guidelines

Use the show bgp route labels command to display MPLS labels associated with BGP routes.

Note:  
By default, most show commands (in any mode) display information for the current context only or, depending on the command syntax, for all contexts. If you are an administrator for the local context, you can insert the optional context ctx-name construct, preceding the show command, to view output for the specified context without entering that context. For more information about using the context ctx-name construct, see the context command description.

Note:  
By appending a space followed by the pipe ( | ) character at the end of a show command, you can filter the output using a set of modifier keywords and arguments. For more information, see Modifying Output of show Commands in Using the CLI. For information about troubleshooting BGP, see the L3VPN Troubleshooting document.

1.21.6   Examples

The following example displays the MPLS labels associated with BGP routes in the local context:

[local]Redback>show bgp route labels
Network            Next Hop            Rcv Label      Alloc Label    

3.0.0.0/8          155.53.0.1          nolabel        nolabel        

                   155.53.0.1          nolabel        nolabel        

4.0.0.0/8          155.53.0.1          nolabel        nolabel        

6.0.0.0/20         155.53.0.1          nolabel        nolabel        

The following example displays the MPLS labels associated with BGP routes in a Virtual Private Network (VPN) context:

[local]Redback>show bgp route labels
VPN RD: 10.11.12.13:100

Network            Next Hop            Rcv Label      Alloc Label    

2.1.0.0/16         10.13.49.207        22             589830         

2.3.0.0/16         10.13.49.207        21             589829         

4.2.1.1/32         10.13.49.207        19             589828         

6.3.0.0/18         192.168.41.100      nolabel        589826 

1.22   show bgp route neighbor

show bgp route neighbor ip-addr{active | advertised | dampened | history | not-advertised | received}

1.22.1   Purpose

Displays information about routes to and from Border Gateway Protocol (BGP) neighbors.

1.22.2   Command Mode

All modes

1.22.3   Syntax Description

ip-addr

IP address of the neighbor.

active

Displays only active BGP routes from the specified neighbor.

advertised

Displays only BGP routes advertised to the specified neighbor.

dampened

Displays only dampened BGP routes from the specified neighbor.

history

Displays a history of the BGP routes form the specified neighbor.

not-advertised

Displays only BGP routes not advertised to the specified neighbor.

received

Displays only BGP routes received from the specified neighbor.

1.22.4   Default

None

1.22.5   Usage Guidelines

Use the show bgp route neighbor command to display information about routes to or from BGP neighbors.

Note:  
By default, most show commands (in any mode) display information for the current context only or, depending on the command syntax, for all contexts. If you are an administrator for the local context, you can insert the optional context ctx-name construct, preceding the show command, to view output for the specified context without entering that context. For more information about using the context ctx-name construct, see the context command description.

Note:  
By appending a space followed by the pipe ( | ) character at the end of a show command, you can filter the output using a set of modifier keywords and arguments. For more information, see Modifying Output of show Commands in Using the CLI. For information about troubleshooting BGP, see the L3VPN Troubleshooting document.

1.22.6   Examples

The following example displays output from the show bgp route neighbor ip-addr active command:

[local]Redback>show bgp route neighbor 192.168.41.7 active
Address Family: ipv4 unicast

BGP table version is 418798, local router ID is 192.168.4.100

Status codes: d damped, h history, > best, i internal

Origin codes: i - IGP, e - EGP, ? - incomplete



   Network            Next Hop          Metric  LocPrf  Weight Path

>  3.3.3.0/24         192.168.41.7           0     100     100 64173 ?

>  4.4.4.0/24         192.168.41.7           0     100     100 64173 ?

>  5.5.5.0/24         192.168.41.7           0     100     100 64173 ?

>  8.8.8.0/24         192.168.41.7           0     100     100 64173 ?

>  10.12.208.81/32    192.168.41.7           0     100     100 64173 ?

>  10.13.208.81/32    192.168.41.7           0     100     100 64173 ?

>  10.100.2.3/32      192.168.41.7           0     100     100 64173 ?

>  155.0.0.0/8        192.168.41.7           0     100     100 64173 ?

>  155.53.1.235/32    192.168.41.7           0     100     100 64173 ?

>  155.53.36.0/24     192.168.41.7           0     100     100 64173 ?

>  165.30.199.0/24    192.168.41.7           0     100     100 64173 14207 64513 2828 2828 2828 2828 701 i

1.23   show bgp route regexp

show bgp route regexpas-path-string...

1.23.1   Purpose

Displays Border Gateway Protocol (BGP) communities that match the specified autonomous system (AS) path string.

1.23.2   Command Mode

All modes

1.23.3   Syntax Description

as-path-string...

One or more AS path strings.

1.23.4   Default

None

1.23.5   Usage Guidelines

Use the show bgp route regex command to display BGP routes that contain the specified AS path string.

Note:  
By default, most show commands (in any mode) display information for the current context only or, depending on the command syntax, for all contexts. If you are an administrator for the local context, you can insert the optional context ctx-name construct, preceding the show command, to view output for the specified context without entering that context. For more information about using the context ctx-name construct, see the context command description.

Note:  
By appending a space followed by the pipe ( | ) character at the end of a show command, you can filter the output using a set of modifier keywords and arguments. For more information, see Modifying Output of show Commands in Using the CLI. For information about troubleshooting BGP, see the L3VPN Troubleshooting document.

1.23.6   Examples

The following example displays output from the show bgp route regex command. Only routes that contain the AS paths, 64173 and 14207, are displayed:

[local]Redback>show bgp route regex 64137 14207
Address Family: ipv4 unicast

BGP table version is 418910, local router ID is 192.168.4.100

Status codes: d damped, h history, > best, i internal

Origin codes: i - IGP, e - EGP, ? - incomplete



Network            Next Hop           Metric  LocPrf   Weight  Path

3.0.0.0/8       192.168.41.7            0     100      100  64173 14207 3944  6461 701  80  i

4.0.0.0/8       192.168.41.7            0     100      100  64173 14207 64513 2828 2828 2828 2828 1 i

4.21.132.0/23   192.168.41.7            0     100      100  64173 14207 64513 2828 2828 2828 2828 6461 
                                                            16422 i

6.1.0.0/16      192.168.41.7            0     100      100  64173 14207 3944  6461 7170 
                                                            1455 i

6.2.0.0/22      192.168.41.7            0     100      100  64173 14207 64513 2828 2828 2828 2828 7170 
                                                            1455 i

6.3.0.0/18      192.168.41.7            0     100      100  64173 14207 3944  6461 7170 1455 i

6.4.0.0/16      192.168.41.7            0     100      100  64173 14207 3944  6461 7170 1455 i

6.5.0.0/19      192.168.41.7            0     100      100  64173 14207 3944  6461 7170 1455 i

1.24   show bgp route sourced

show bgp route sourced

1.24.1   Purpose

Displays Border Gateway Protocol (BGP) routes sourced from the local autonomous system (AS).

1.24.2   Command Mode

All modes

1.24.3   Syntax Description

This command has no keywords or arguments.

1.24.4   Default

None

1.24.5   Usage Guidelines

Use the show bgp route sourced command to display BGP routes sourced from the local autonomous system.

Note:  
By default, most show commands (in any mode) display information for the current context only or, depending on the command syntax, for all contexts. If you are an administrator for the local context, you can insert the optional context ctx-name construct, preceding the show command, to view output for the specified context without entering that context. For more information about using the context ctx-name construct, see the context command description.

Note:  
By appending a space followed by the pipe ( | ) character at the end of a show command, you can filter the output using a set of modifier keywords and arguments. For more information, see Modifying Output of show Commands in Using the CLI. For information about troubleshooting BGP, see the L3VPN Troubleshooting document.

1.24.6   Examples

The following snapshot from a configuration file enables the output for the show bgp route sourced command example:

router bgp 64001

 address-family ipv4 unicast

  redistribute static

!

ip route 0.0.0.0/0 10.13.49.254

ip route 10.0.0.0/8 10.13.49.254

ip route 155.0.0.0/8 10.13.49.254

ip route 155.53.36.126/32 10.13.49.254

The previous configuration provides the commands that enable the following output:

[local]Redback>show bgp route sourced
Address Family: ipv4 unicast

BGP table version is 418884, local router ID is 192.168.4.100

Status codes: d damped, h history, > best, i internal

Origin codes: i - IGP, e - EGP, ? - incomplete



   Network            Next Hop             Metric  LocPrf  Weight  Path

>  10.0.0.0/8         10.13.49.254         0       100     32768   ?

>  155.0.0.0/8        10.13.49.254         0       100     32768   ?

>  155.53.36.126/32   10.13.49.254         0       100     32768   ?

1.25   show bgp route summary

show bgp route summary

1.25.1   Purpose

Displays a summary report of Border Gateway Protocol (BGP) routes in the BGP routing table.

1.25.2   Command Mode

All modes

1.25.3   Syntax Description

This command has no keywords or arguments.

1.25.4   Default

None

1.25.5   Usage Guidelines

Use the show bgp route summary command to display a summary report of BGP routes in the BGP routing table.

Note:  
By default, most show commands (in any mode) display information for the current context only or, depending on the command syntax, for all contexts. If you are an administrator for the local context, you can insert the optional context ctx-name construct, preceding the show command, to view output for the specified context without entering that context. For more information about using the context ctx-name construct, see the context command description.

Note:  
By appending a space followed by the pipe ( | ) character at the end of a show command, you can filter the output using a set of modifier keywords and arguments. For more information, see Modifying Output of show Commands in Using the CLI. For information about troubleshooting BGP, see the L3VPN Troubleshooting document. .

1.25.6   Examples

The following example displays output from the show bgp route summary command:

[local]Redback>show bgp route summary
Address Family: ipv4 unicast

BGP router identifier: 0.0.0.0, local AS number: 100

BGP route table version: 0, RIB table version: 0

Neighbors Configured: 4, Established: 0

Sourced paths: redistributed: 0, networked: 0, aggregated: 0



Entry Type       Count          Memory

Network          103389       10880700

Path             393376       12588032



Neighbor        AS       MsgRcvd MsgSent TblVer InQ OutQ Rst  Up/Down PfxRcvd/Sent

10.11.64.99     14207    0       0       0      0   0    0    1w0d    Connect

10.11.64.170    64001    0       0       0      0   0    0    1w0d    Idle

10.12.208.76    64001    104681  68515   247945 0   0    1    6d21h   83582 103070

10.12.208.85    64001    0       0       0      0   0    0    1w0d    Connect

10.12.208.89    100      0       1461    0      0   0    0    1w0d    Idle

10.12.209.136   10000    0       1428    0      0   0    0    1w0d    Idle

10.13.49.122    64001    205930  48263   247945 0   0    6    5d17h   103107 103070

10.13.49.173    64173    0       0       0      0   0    0    1w0d    Idle (admin)

10.13.49.174    200      0       1456    0      0   0    0    1w0d    Idle

10.100.2.1      64001    0       0       0      0   0    0    1w0d    Connect

10.100.2.2      64001    0       0       0      0   0    0    1w0d    Connect

10.100.200.1    64001    0       0       0      0   0    0    1w0d    Connect

155.53.1.235    14207    48126   14552   247945 0   0    0    1w0d    103151 19641

155.53.1.236    64513    51801   37437   247945 0   0    0    1w0d    102592 83518

1.26   show bgp summary

show bgp summary

1.26.1   Purpose

Displays a summary of Border Gateway Protocol (BGP) status and statistical information.

1.26.2   Command Mode

All modes

1.26.3   Syntax Description

This command has no keywords or arguments.

1.26.4   Default

None

1.26.5   Usage Guidelines

Use the show bgp summary command to display a summary of BGP status and statistical information.

Note:  
By default, most show commands (in any mode) display information for the current context only or, depending on the command syntax, for all contexts. If you are an administrator for the local context, you can insert the optional context ctx-name construct, preceding the show command, to view output for the specified context without entering that context. For more information about using the context ctx-name construct, see the context command description.

Note:  
By appending a space followed by the pipe ( | ) character at the end of a show command, you can filter the output using a set of modifier keywords and arguments. For more information, see Modifying Output of show Commands in Using the CLI. For information about troubleshooting BGP, see the L3VPN Troubleshooting document.

1.26.6   Examples

The following example displays output from the show bgp summary command:

[local]Redback>show bgp summary
Address Family: ipv4 unicast

BGP router identifier: 10.10.10.10, local AS number: 4

BGP route table version: 0, RIB table version: 0

Neighbors Configured: 2, Established: 0

Sourced paths: redistributed: 0, networked: 0

Dampening: Disabled



Entry Type      Count          Memory   Total Alloc

Network             0              24             0

Path                0               0             0



Neighbor           AS MsgRcvd MsgSent   TblVer  InQ OutQ  Up/Down   PfxRcvd/Sent

10.10.2.2           5       0       0        0    0    0  03:35:19  Idle

10.10.10.1          0       0       0        0    0    0  02:08:19  Idle (noAS)

1.27   show bindings

To show bindings information for a specific type of circuit, the syntax is as follows:

show bindings [circuit-type] [bind-type] [up | down] [detail | summary]

To show bindings information of circuits assigned to a subscriber identified by the RADIUS Agent-Remote-ID or Agent-Circuit-ID attributes, the syntax is:

show bindings [agent-remote-id agent-remote-id | agent-circuit-id agent-circuit-id] [up | down] [detail | summary]

To show the bindings information of circuits assigned to BVI ports, the syntax is:

show bindings [bvi {bvi-name | id bvi-id}] [circuit-type] [bind-type] [up | down] [detail | summary]

To show bindings information of l2vpn cross-connect circuits, the syntax is:

show bindings [l2vpn-cross-connect [cross-connect-prof-id]] [circuit-type] [bind-type] [up | down] [detail | summary]

To show the bindings information of aggregated circuits of a link group, the syntax is:

show bindings [lg {lg-name | id lg-id}] [circuit-type] [bind-type] [up | down] [detail | summary]

To show the bindings information of a circuit connected to a specific slot and port and optionally the circuit type, the syntax is:

show bindings [slot/port[:chan[:sub-chan]] [{circuit-id | circuit-type} [bind-type]] [up | down] [detail | summary]

To show the bindings information of circuits assigned to a subscriber identified by a fully qualified subscriber name, the syntax is:

show bindings [username subscriber] [up | down] [detail | summary]

1.27.1   Purpose

Displays information on the configured bindings of one or more subscribers, ports, channels, or permanent virtual circuits (PVCs) on the system.

1.27.2   Command Mode

All modes

1.27.3   Syntax Description

circuit-type

Type of circuit for which bindings information is displayed. If omitted, displays bindings information for all types of circuits.The circuit-type keywords are: atm, chdlc, clips, dot1q, ether, fr, gre, ipip, ipsec, ipv6-auto, ipv6-man, l2tp, mip-fa, mip-ha, mp, mpls, ppp, pppoe, and vpls. See Table 4 for the components of this argument.

bind-type

Type of binding for which bindings information is displayed, according to one of the keywords listed in Table 5.

up

Displays only circuits that are up.

down

Displays only circuits that are down.

detail

Displays detailed bindings information.

summary

Displays only summary information.

agent-circuit-id agent-circuit-id

Specifies the RADIUS Agent-Circuit-ID attribute of the subscriber session.


agent-circuit-id is a text string of up to 63 alphanumeric characters.

agent-remote-id agent-remote-id

Specifies a subscriber session.


agent-remote-id is the value of the Agent-Remote-ID attribute in a RADIUS subscriber record. Enter the agent-remote-id argument as a structured subscriber username in the form subscriber@context. A text string of up to 63 alphanumeric characters.

bvi {bvi-name | id bvi-id}

Specifies the name or ID of a Bridged Virtual Interface for which bindings information is displayed.

counters

Displays the circuit counters. The show bindings counters command provides the same information as the show circuit counters command. See show circuit counters.

lg {lg-name | id lg-id}

Displays bindings information for all the circuits associated with the specified link or APS group.

slot/port

Chassis slot and port number of a traffic card for which bindings information is displayed. The port argument is required if you enter the slot argument.

chan-num

Channel number for which bindings information is displayed. If omitted, displays bindings information for all channels on the specified port. The range of values depends on the type of port; see Table 7 for the range of values.

sub-chan-num

Subchannel number for which bindings information is displayed. If omitted, displays bindings information for all subchannels in the specified channel. The range of values depends on the type of port; see Table 7 for the range of values.

circuit-id

Circuit identifier, according to one of the constructs listed in Table 6. If omitted, displays bindings information for all circuits on the specified port or channel.

username subscriber

A fully qualified subscriber name for which bindings information is displayed. Enter in the format sub-name@ctx-name.

Note:  
Keywords and arguments not listed in the Syntax Description table are listed in Table 4, Table 5, and Table 6 of the Usage Guidelines section.

1.27.4   Default

Displays bindings information for all ports, channels, or circuits that are bound within the current context.

1.27.5   Usage Guidelines

Use the show bindings command to display information on the configured bindings of one or more subscribers, ports, channels, or permanent virtual circuits (PVCs) on the system.

If you specify the VLAN tag value for an 802.1Q tunnel, the output includes bindings information for all the PVCs within the tunnel.

Note:  
By default, most show commands (in any mode) display information for the current context only or, depending on the command syntax, for all contexts. If you are an administrator for the local context, you can insert the optional context ctx-name construct, preceding the show command, to view output for the specified context without entering that context. For more information about using the context ctx-name construct, see the context command description.

Note:  
By appending a space followed by the pipe ( | ) character at the end of a show command, you can filter the output using a set of modifier keywords and arguments. For more information, see Using the CLI.

Table 4 lists the options for the circuit-type argument.

Table 4    Options for the circuit-type Argument

Circuit Type (circuit-type)

Description

atm

Specifies ATM circuits.

chdlc

Specifies Cisco HDLC circuits.(1)

clips

Specifies CLIPS circuits.

dot1q

Specifies 802.1Q circuits.

ether

Specifies Ethernet circuits.

fr

Specifies Frame Relay circuits.(2)

gre [gre-id]

Specifies GRE tunnel circuits.

ipip [ipip-id]

Specifies IPIP tunnel circuits.

ipsec [ipsec-id]

Specifies IPSec encrypted tunnel.

ipv6-auto [ipv6-auto-id]

Specifies automatic IPv6 tunnel circuits.

ipv6-man [ipv6-man-id]

Specifies manual IPv6 tunnel circuits.

l2tp...

Specifies L2TP circuits


Syntax: l2tp {l2tp-peer tunnel l2tp-id session session-id | active-slot [active-slot-num] | all | lns lns-circuit-id}


  • l2tp-peer - Name of the L2TP peer.

  • tunnel l2tp-id - L2TP circuit identifier.

  • session session-id - Session identifier

  • active-slot active-slot-num - Slot number.

  • all - Specifies all L2TP LNS circuits.

  • lns lns-circuit-id - LNS circuit identifier.


mip-fa [mip-fa-id]

Specifies mobile-ip foreign agent (FA) circuits.

mip-ha [mip-ha-id]

Specifies mobile-ip home agent (HA) circuits.

mp mp-id

Specifies multilink PPP link group circuits

mpls [lsp lsp-id]

Specifies MPLS circuits, where lsp-id is the label-switched path (LSP) identifier. The range of values is 1 to 65535.

ppp

Specifies PPP circuits.

pppoe

Specifies PPPoE circuits

vpls [vpls-id]

Specifies VPLS circuits. The range of values is 1 to 65535.

(1)  The SmartEdge 100 router does not support the chdlc keyword.

(2)  The SmartEdge 100 router does not support the fr keyword.


Table 5 lists the keyword choices for the bind-type argument.

Table 5    The bind-type Argument

Keyword (bind-type)

Description

auth

Display information for circuits that are bound using PAP or CHAP.

bound

Display information for circuits that are bound.

bypass

Display information for cross connected circuits.

interface

Display information for circuits that are bound to an interface.

no-bind

Display information for circuits that have no binding

subscriber

Display information for circuits that are bound to subscribers.

unbound

Display information for unbound circuits.

Table 6 lists the values for the circuit-id argument.

Table 6    The circuit-id Argument

Circuit ID (circuit-id)

Description

dlci dlci-id

Specifies the data-link connection identifier (DLCI) of a Frame Relay PVC. The range of values is 16 to 991.

vlan-id...

Specifies an 802.1Q tunnel or PVC, and optionally, whether the circuit is CLIPS, IPv6oE, or PPPoE encapsulated.


Syntax: vlan-id {pvc-vlan-id | tunl-vlan-id | tunl-vlan-id:pvc-vlan-id} [clips [clips-id] | ipv6oe | pppoe [pppoe-id]]

 

pvc-vlan-id

Specifies the VLAN tag value of a PVC that is not within an 802.1Q tunnel. Range is 1 to 4095.

tunl-vlan-id

Specifies the VLAN tag value of a tunnel. Range is 1 to 4095.

tunl-vlan-id:pvc-vlan-id

Specifies the VLAN tag value of a tunnel followed by the VLAN tag value for the PVC within the tunnel. Range of each is 1 to 4095.

clips [clips-id]

Specifies CLIPS circuits.

ipv6oe

Specifies IPv6oE circuits.

pppoe [pppoe-id]

Specifies PPPoE circuits.

vpi-vci...

Specifies the circuit-id argument using the Virtual path identifier (VPI) and virtual circuit identifier (VCI) of an ATM PVC.


The circuit-id argument of an ATM PVC has the following syntax:


Syntax: vpi-vci vpi-id vci-id [clips [clips-id] | ipv6oe | pppoe [pppoe-id]]

 

vpi-vci vpi-id vci-id

Specifies the circuit-id argument using the VPI and VCI IDs of an ATM PVC. The range of values for the arguments are 0 to 255 and 1 to 65535, respectively.

Table 7 lists the range of values for the chan-num and sub-chan-num arguments for various types of channelized ports.

Table 7    Range of Values for the chan-num and sub-chan-num Arguments

Port

Channel Types

chan-num Range

sub-chan-num Range

Channelized OC-12

DS-3, DS-1

1 to 12

1 to 28

Channelized STM-1

E1, DS-0 channel group

1 to 63

1 to 31

Channelized DS-3

DS-1

1 to 28

Channelized E1

DS-0 channel group

1 to 31

1.27.6   Examples

The following example displays all bindings in the current context (local):

[local]Redback#show bindings
Circuit                       State Encaps           Bind Type  Bind Name

4/1                           Up    ethernet
4/1 vlan-id 100               Up    eth dot1q pppoe  chap
4/2                           Down  ethernet
4/4                           Down  ethernet
4/11                          Up    ethernet
4/12                          Up    ethernet
7/1                           Up    ethernet         interface  mgmt@local
10/1                          Down  ethernet
10/1 vlan-id 100              Down  eth dot1q pppoe  chap
lg id 25 lag                  Down  ethernet
lg id 25 vlan-id 100          Down  dot1q
lg id 25 vlan-id 101          Down  dot1q
GRE 1                         Down  gre              interface  link-gre@myISP-Ctx
blue-lg                       Down  ethernet         interface  etherx@local
Link share ethernet           Down  ethernet

Summary:
    total: 15
       up: 5              down: 9
    bound: 3           unbound: 14
     auth: 2         interface: 3       subscriber: 0           bypass: 0
     no-bind: 10           atm: 0            chdlc: 0            dot1q: 2
       ether: 10           fr: 0              gre: 1
        mpls: 0              ppp: 0         pppoe: 2
       clips: 0             vpls: 0          ipip: 0
       ipsec: 0       ipv6v4-man: 0      ipv6v4-auto: 0

1.28   show bridge associations

show bridge associations {bridge-name ctx-name [detail] | all [detail] | circuit slot/port [circuit-id]}

1.28.1   Purpose

Displays bridge profile permanent virtual circuit (PVC) assignments.

1.28.2   Command Mode

All modes

1.28.3   Syntax Description

bridge-name

Name of the bridge with associations to be displayed.

ctx-name

Name of the context in which the bridge exists with associations to be displayed.

detail

Optional. Displays detailed information.

all

Displays the bridge forwarding table for all bridges in all contexts.

circuit

Displays the bridge forwarding table for the specified bridged port or PVC.

slot

Chassis slot number of the traffic card with the bridged port or PVC.

port

Port number of the bridged port or the port with the bridged PVC.

circuit-id

Optional. Bridged PVC identifier, according to one of the constructs listed in Table 8.

1.28.4   Default

Displays associations for all bridges in the current context.

1.28.5   Usage Guidelines

Use the show bridge associations command to display bridge profile PVC assignments.


 Caution! 
Risk of performance loss. Enabling the generation of debug messages can severely affect system performance. To reduce the risk, exercise caution before enabling the generation of any debug messages on a production system.

Use the circuit slot/portcircuit-id construct to display the association for that bridged PVC.

Note:  
The SmartEdge 100 router limits the value of the slot argument to 2.

Note:  
The value for the port argument on the SmartEdge 100 router depends on the MIC slot in which the MIC is installed.

Table 8 lists the values for the circuit-id argument.

Table 8    Values for the circuit-id Argument

Field

Field

vlan vlan-id

A filter that limits the command to a specified virtual LAN (VLAN) 802.1Q tunnel or PVC. The vlan-id argument is one of the following constructs:


  • pvc-vlan-id—VLAN tag value of a PVC that is not within an 802.1Q tunnel.

  • tunl-vlan-id—VLAN tag value of an 802.1Q tunnel.

  • tunl-vlan-id:pvc-vlan-id—VLAN tag value of an 802.1Q tunnel followed by the VLAN tag value for the PVC within the tunnel.


The range of values for any VLAN tag value is 1 to 4095.

vpi-vci vpi vci

Virtual path identifier (VPI) and virtual circuit identifier (VCI) for an Asynchronous Transfer Mode (ATM) permanent virtual circuit (PVC). The range of values is 0 to 255 and 1 to 65535, respectively.

Use the all keyword to display associations for all bridges in all contexts.

Note:  
By default, most show commands (in any mode) display information for the current context only or, depending on the command syntax, for all contexts. If you are an administrator for the local context, you can insert the optional context ctx-name construct, preceding the show command, to view output for the specified context without entering that context. For more information about using the context ctx-name construct, see the context command description.

Note:  
By appending a space followed by the pipe ( | ) character at the end of a show command, you can filter the output using a set of modifier keywords and arguments. For more information, see Modifying Output of show Commands in Using the CLI.

1.28.6   Examples

The following example displays associations for all bridges:

[local]Redback#show bridge associations all
Bridge Profile       Circuit   

trib                 3/1       

trunk                3/2 

1.29   show bridge bindings

show bridge bindings {bridge-name ctx-name | all | {circuit slot/port [circuit-id]}} [detail | tracking]

1.29.1   Purpose

Displays bridge binding information for one or more bridges or for a bridged permanent virtual circuit (PVC).

1.29.2   Command Mode

All modes

1.29.3   Syntax Description

bridge-name

Name of the bridge with binding information to be displayed.

ctx-name

Name of the context in which the bridge exists.

detail

Optional. Displays detailed information.

all

Displays the bridge forwarding table for all bridges in all contexts.

circuit

Displays the bridge forwarding table for the specified bridged port or PVC.

slot

Chassis slot number of the traffic card with the bridged port or PVC.

port

Port number of the bridged port or the port with the bridged PVC.

circuit-id

Optional. Bridged PVC identifier, according to one of the constructs listed in Table 9.

tracking

Optional. Displays RSTP master and client tracking information.

1.29.4   Default

Displays bindings for all bridges in the current context.

1.29.5   Usage Guidelines

Use the show bridge bindings command to display bridge binding information for one or more bridges or for a bridged PVC.

Use the circuit slot/port circuit-id construct to display the binding for that bridged PVC.

Note:  
The SmartEdge 100 router limits the value of the slot argument to 2.

Note:  
The value for the port argument on the SmartEdge 100 router depends on the MIC slot in which the MIC is installed.

Table 9 lists the values for the circuit-id argument.

Table 9    Values for the circuit-id Argument

Field

Field

vlan vlan-id

A filter that limits the command to a specified virtual LAN (VLAN) 802.1Q tunnel or PVC. The vlan-id argument is one of the following constructs:


  • pvc-vlan-id—VLAN tag value of a PVC that is not within an 802.1Q tunnel.

  • tunl-vlan-id—VLAN tag value of an 802.1Q tunnel.

  • tunl-vlan-id:pvc-vlan-id—VLAN tag value of an 802.1Q tunnel followed by the VLAN tag value for the PVC within the tunnel.


The range of values for any VLAN tag value is 1 to 4095.

vpi-vci vpi vci

Virtual path identifier (VPI) and virtual circuit identifier (VCI) for an Asynchronous Transfer Mode (ATM) PVC. The range of values is 0 to 255 and 1 to 65535, respectively.

Use the all keyword to display bindings for all bridges in all contexts.

Note:  
By default, most show commands (in any mode) display information for the current context only or, depending on the command syntax, for all contexts. If you are an administrator for the local context, you can insert the optional context ctx-name construct, preceding the show command, to view output for the specified context without entering that context. For more information about using the context ctx-name construct, see the context command description.

Note:  
By appending a space followed by the pipe ( | ) character at the end of a show command, you can filter the output using a set of modifier keywords and arguments. For more information, see Modifying Output of show Commands in Using the CLI.

1.29.6   Examples

The following example displays detailed binding information for all bridges:

[local]Redback#show bridge bindings all detail 
Flags are,(L)earning,(D)ynamic,(t)ributary,(T)runk,
(R)estricted,(d)eleted,(S)tale,(l)og,(U)p, (Ld) Loop Detection
(D)eny bpdu,(O)nly bpdu,(A)llow bpdu (default), (F) stp state forwarding
(B) stp state discarding
Headings : Ld Pri - Loop Detection Priority
           (Bpdu Pri)- bridge protocol data unit Priority
Context   Bridge Group  Circuit MAC  D-MAC Limit  Flag         Ld Pri Bpdu Pri
local     b1            2/1     0    0     4      L-t----U--AF 0        -

The show bridge bindings all tracking command identifies the tracking masters and clients, their contexts, and circuits. It also shows the RSTP status of circuits bound to the bridges.

[local]Redback#show bridge bindings all tracking 

Context              Bridge Group         Circuit                Stp State    Role    clients
local                bridge30             3/2                    FORWARD      MASTER  1    
local                bridge2              3/2 vlan-id 2          FORWARD      CLIENT  - 
local                bridge30             3/3                    FORWARD      MASTER  1    
local                bridge2              3/3 vlan-id 2          FORWARD      CLIENT  - 

1.30   show bridge info

show bridge info {bridge-name ctx-name [detail] | all [detail]}

1.30.1   Purpose

Displays information for configured bridges.

1.30.2   Command Mode

All modes

1.30.3   Syntax Description

bridge-name

Name of the bridge with information to be displayed.

ctx-name

Name of the context in which the bridge exists.

detail

Optional. Displays detailed information.

all

Displays information for bridges in all contexts.

1.30.4   Default

Displays bridge information for all bridges in the current context.

1.30.5   Usage Guidelines

Use the show bridge info command to display information for configured bridges.

Use the all keyword to display information for all bridges in all contexts.

Note:  
By default, most show commands (in any mode) display information for the current context only or, depending on the command syntax, for all contexts. If you are an administrator for the local context, you can insert the optional context ctx-name construct, preceding the show command, to view output for the specified context without entering that context. For more information about using the context ctx-name construct, see the context command description.

Note:  
By appending a space followed by the pipe ( | ) character at the end of a show command, you can filter the output using a set of modifier keywords and arguments. For more information, see Modifying Output of show Commands in Using the CLI.

1.30.6   Examples

The following example displays information for all bridges:

[local]Redback#show bridge info all



Type can be: (L)earning,(D)ynamic,(R)outing

Context          Bridge Group     Type Ccts  Aging MAC   D-MAC Description     

c1               b1               L--  1     300   6     3     Bridge one 

c1               b2               L--  1     300   1     0     Bridge two

c1               b3               L--  1     300   0     0     Bridge three

c1               b4               L--  1     300   0     0     Bridge four

The following example illustrates the show bridge command with the info keyword. The bridge name is red and the context name is ink. In this example information is provided on loop-detection using the MAC moves method:

[local]Redback(config-bridge)#show bridge info lbdl ink

Type can be: (L)earning,(R)outing,(Md) MacMove Drop

Context          Bridge Group     Type Ccts  Aging MAC   D-MAC PW-Ccts Description

ink              lbdl             L--   0     300   0     0      0

1.31   show bridge loop-detection

show bridge loop-detection bridge-name context-name

1.31.1   Purpose

Shows the MAC moves loop detection status of the specified bridge.

1.31.2   Command Mode

Exec

1.31.3   Syntax Description

bridge-name

Name of the bridge.

context-name

Name of the context that contains the bridge.

1.31.4   Default

None

1.31.5   Usage Guidelines

Use the show bridge loop-detection command to the MAC moves loop detection status of the specified bridge.

1.31.6   Examples

The following example illustrates the show bridge command with the loop-detection keyword:

[local]pearl#show bridge loop-detection all

Context      Bridge Group BlkTime     Interval MoveFreq   AggrMoves    cpuMoves
local        bvi          60          5        0          0            0

    Circuit              State Priority Aggr Moves   CPU Moves    Retry(s) CurRetry
    9/1 vlan-id 30       Up    1        0            0            0        0
    lg id 33 vlan-id 80  Up    3        0            0            0        0
    test2 vlan-id 81     Up    3        0            0            0        0

1.32   show bridge profile

show bridge profile [prof-name] [all]

1.32.1   Purpose

Displays information for configured bridge profiles.

1.32.2   Command Mode

All modes

1.32.3   Syntax Description

prof-name

Optional. Name of the bridge profile with information to be displayed.

all

Optional. Displays information for bridge profiles in all contexts.

1.32.4   Default

Displays bridge profile information for all bridge profiles in the current context.

1.32.5   Usage Guidelines

Use the show bridge profile command to display information for configured bridge profiles.

Use the all keyword to display information for all bridge profiles in all contexts.

Note:  
By default, most show commands (in any mode) display information for the current context only or, depending on the command syntax, for all contexts. If you are an administrator for the local context, you can insert the optional context ctx-name construct, preceding the show command, to view output for the specified context without entering that context. For more information about using the context ctx-name construct, see the context command description.

Note:  
By appending a space followed by the pipe ( | ) character at the end of a show command, you can filter the output using a set of modifier keywords and arguments. For more information, see Modifying Output of show Commands in Using the CLI.

1.32.6   Examples

The following example displays information for all bridge profiles:

[local]Redback#show bridge profile all       
Flags are: (R)estricted,(t)ributary,(T)runk

Profile              Flag Circuits

pbr                  Rt    0

pbu                  -t    5

pkr                  RT    0

pku                  -T    8

1.33   show bridge statistics

show bridge statistics {bridge-name ctx-name | all}

1.33.1   Purpose

Displays statistics for one or more configured bridges.

1.33.2   Command Mode

All modes

1.33.3   Syntax Description

bridge-name

Name of the bridge with statistics to be displayed.

ctx-name

Name of the context in which the bridge exists.

all

Displays statistics for all bridges in all contexts.

1.33.4   Default

Displays statistics for all bridges in the current context.

1.33.5   Usage Guidelines

Use the show bridge statistics command to display statistics for one or more configured bridges. Table 10 lists the fields that are displayed for each bridge.

Table 10    Field Descriptions for the show bridge statistics Command

Field

Field

Context

Context in which the bridge is configured.

Bridge Group

Name of the bridge.

Static MAC

Number of static medium access control (MAC) addresses configured (using the bridge mac-entry command in dot1q PVC, ATM PVC, or port configuration mode) for each bridged 802.1Q PVC, ATM PVC, or Ethernet port in this bridge.

Drop MAC

Number of MAC addresses specified as dropped (using the mac-entry command (in bridge configuration mode).

Dynamic MAC

Number of MAC addresses learned by the bridge.

MCAST

Number of multicast or broadcast MAC addresses.

Station Move

Number of station moves that have occurred on the circuits for this bridge.

S Move Reject

Number of station moves rejected for this bridge because of either of the following conditions:


  • Bridging restrictions (tributary to trunk circuit, static MAC address).

  • Rapid station moves.

Note:  
By default, most show commands (in any mode) display information for the current context only or, depending on the command syntax, for all contexts. If you are an administrator for the local context, you can insert the optional context ctx-name construct, preceding the show command, to view output for the specified context without entering that context. For more information about using the context ctx-name construct, see the context command description.

Note:  
By appending a space followed by the pipe ( | ) character at the end of a show command, you can filter the output using a set of modifier keywords and arguments. For more information, see Modifying Output of show Commands in Using the CLI.

1.33.6   Examples

The following example displays statistics for all bridges:

[local]Redback#show bridge statistics all
Context          Bridge Group     Static Drop  Dynamic MCAST Station S Move

                                  MAC    MAC   MAC           Move    Reject

c1               b1               0      0     51      0     0       0     

c1               b2               0      0     51      0     0       0     

c2               b3               0      0     55      0     0       0     

The following example displays statistics for a specific bridge:

[local]Redback#show bridge statistics b1 c1



Context          Bridge Group     Static Drop  Dynamic MCAST Station S Move

                                  MAC    MAC   MAC           Move    Reject

c1               b1               0      0     51      0     0       0 

1.34   show bridge table

show bridge table {bridge-name ctx-name [detail] | all [detail] | circuit slot/port [circuit-id]}

1.34.1   Purpose

Displays the bridge forwarding table for one or more bridges or for a bridged permanent virtual circuit (PVC).

1.34.2   Command Mode

All modes

1.34.3   Syntax Description

bridge-name

Name of the bridge with the bridge forwarding table to be displayed.

ctx-name

Name of the context in which the bridge exists.

detail

Optional. Displays detailed information from the bridge forwarding table.

all

Displays the bridge forwarding table for all bridges in all contexts.

circuit

Displays the bridge forwarding table for the specified bridged port or PVC.

slot

Chassis slot number of the traffic card with the bridged port or PVC.

port

Port number of the bridged port or the port with the bridged PVC.

circuit-id

Optional. Bridged PVC identifier, according to one of the constructs listed in Table 11.

1.34.4   Default

None

1.34.5   Usage Guidelines

Use the show bridge table command to display the bridge forwarding table for one or more bridges or for a bridged PVC.

Note:  
The SmartEdge 100 router limits the value of the slot argument to 2.

Note:  
The value for the port argument on the SmartEdge 100 router depends on the MIC slot in which the MIC is installed.

Use the circuit slot/port circuit-id construct to display all bridge forwarding entries for that circuit.

Table 11 lists the values for the circuit-id argument.

Table 11    Values for the circuit-id Argument

Field

Field

vlan vlan-id

A filter that limits the command to a specified virtual LAN (VLAN) 802.1Q tunnel or PVC. The vlan-id argument is one of the following constructs:


  • pvc-vlan-id—VLAN tag value of a PVC that is not within an 802.1Q tunnel.

  • tunl-vlan-id—VLAN tag value of an 802.1Q tunnel.

  • tunl-vlan-id:pvc-vlan-id—VLAN tag value of an 802.1Q tunnel followed by the VLAN tag value for the PVC within the tunnel.


The range of values for any VLAN tag value is 1 to 4095.

vpi-vci vpi vci

Virtual path identifier (VPI) and virtual circuit identifier (VCI) for an Asynchronous Transfer Mode (ATM) PVC. The range of values is 0 to 255 and 1 to 65535, respectively.

Use the all keyword to display the bridge forwarding tables for all bridges in all contexts.

Note:  
By appending a space followed by the pipe ( | ) character at the end of a show command, you can filter the output using a set of modifier keywords and arguments. For more information, see Modifying Output of show Commands in Using the CLI.

Table 12 lists the fields that are displayed for each bridge; some fields are displayed only when the detail keyword is specified.

Table 12    Field Descriptions for the show bridge table Command

Field

Field

Context

Context in which the bridge is configured.

Bridge Group

Name of the bridge.

MAC

MAC address of any type, as indicated by the Flag field.

Circuit

Slot, port, circuit identifier (VLAN tag value) on which the MAC address appears.

Slot

Displayed with the detail keyword only.

Flag

Displayed with the detail keyword only. Describes the MAC address or circuit, according to one or more of the following conditions:


  • D—Dropped MAC address

  • d—Duplicate MAC address

  • I—Ignored for now, to be validated, and might be purged later

  • i—Invalid MAC address

  • S—Static MAC address

  • T—Trunk circuit

  • t—Tributary circuit

  • U—Unbound circuit

Static MAC

Displayed with the detail keyword only. Number of static MAC addresses configured (using the bridge mac-entry command in dot1q PVC, ATM PVC, or port configuration mode) for each bridged 802.1Q PVC, ATM PVC, or Ethernet port for all bridges that are displayed.

Drop MAC

Displayed with the detail keyword only. Number of MAC addresses specified as dropped (using the mac-entry command (in bridge configuration mode) for all bridges that are displayed.

Dynamic MAC

Displayed with the detail keyword only. Number of MAC addresses learned by the bridges that are displayed.

MCAST

Displayed with the detail keyword only. Number of multicast or broadcast MAC addresses for all bridges that are displayed.

Note:  
By default, most show commands (in any mode) display information for the current context only or, depending on the command syntax, for all contexts. If you are an administrator for the local context, you can insert the optional context ctx-name construct, preceding the show command, to view output for the specified context without entering that context. For more information about using the context ctx-name construct, see the context command description.

Note:  
By appending a space followed by the pipe ( | ) character at the end of a show command, you can filter the output using a set of modifier keywords and arguments. For more information, see Modifying Output of show Commands in Using the CLI.

1.34.6   Examples

The following example displays the bridge forwarding table for a specific bridge:

[local]Redback>show bridge table b1 c1
Context          Bridge Group     MAC               Circuit         

c1               b1               00:00:0c:47:00:f8 3/1 vlan-id 5   

c1               b1               00:00:0c:5c:df:29 3/1 vlan-id 5   

c1               b1               00:01:02:78:01:35 3/1 vlan-id 5   

C1               b1               00:01:02:e8:f0:45 3/1 vlan-id 5   

c1               b1               00:01:03:67:f3:c0 3/1 vlan-id 5   

c1               b1               00:02:3b:01:71:1d 3/1 vlan-id 5   

c1               b1               00:02:3b:01:79:14 3/1 vlan-id 5   

c1               b1               00:02:3b:01:79:15 3/1 vlan-id 5   

C1               b1               00:02:3b:01:81:d6 3/1 vlan-id 5 

The following example displays the detailed output with the summary data for the same bridge:

[local]Redback>show bridge table b1 c1 detail
Flags:(U)nbound,(D)rop,(S)tatic,(d)uplicate,(T)runk,(t)rib,(I)gnore,(i)nvalid

Context        Bridge Group   MAC               Circuit          Slot Flag   

c1             b1             00:00:0c:47:00:f8 3/1 vlan-id 5    c    ---T---

c1             b1             00:00:0c:5c:df:29 3/1 vlan-id 5    c    ---T---

c1             b1             00:01:02:78:01:35 3/1 vlan-id 5    c    ---T---

c1             b1             00:01:02:e8:f0:45 3/1 vlan-id 5    c    ---T---

c1             b1             00:01:03:67:f3:c0 3/1 vlan-id 5    c    ---T---

c1             b1             00:02:3b:01:71:1d 3/1 vlan-id 5    c    ---T---

c1             b1             00:02:3b:01:79:14 3/1 vlan-id 5    c    ---T---

c1             b1             00:30:88:00:01:1b 3/1 vlan-id 5    c    ---T---

c1             b1             00:30:88:00:05:cc 3/1 vlan-id 5    c    ---T---

c1             b1             00:30:88:00:0b:2a 3/1 vlan-id 5    c    ---T---

c1             b1             00:30:88:00:0b:2d 3/1 vlan-id 5    c    ---T---

c1             b1             00:30:88:00:0b:52 3/1 vlan-id 5    c    ---T---

c1             b1             00:40:9d:21:fd:67 3/1 vlan-id 5    c    ---T---

c1             b1             00:40:9d:22:39:01 3/1 vlan-id 5    c    ---T---

c1             b1             00:50:04:07:a8:9a 3/1 vlan-id 5    c    ---T---

c1             b1             00:50:04:70:b9:e6 3/1 vlan-id 5    c    ---T---

c1             b1             00:50:04:73:30:2e 3/1 vlan-id 5    c    ---T---

c1             b1             00:50:04:c6:61:bc 3/1 vlan-id 5    c    ---T---

c1             b1             00:50:04:c9:f4:a2 3/1 vlan-id 5    c    ---T---

c1             b1             00:50:da:b6:62:b3 3/1 vlan-id 5    c    ---T---

c1             b1             00:80:d4:00:11:2d 3/1 vlan-id 5    c    ---T---

c1             b1             00:a0:cc:59:86:ab 3/1 vlan-id 5    c    ---T---

c1             b1             00:c0:b7:a3:40:da 3/1 vlan-id 5    c    ---T---

c1             b1             00:d0:b7:09:e6:f9 3/1 vlan-id 5    c    ---T---

c1             b1             00:d0:b7:09:e9:07 3/1 vlan-id 5    c    ---T---



Static MAC = 0, Dynamic MAC = 25, Drop MAC = 0, Multicast = 0

1.35   show bridge table mac-entry

show bridge table mac-entry mac-addr {all | bridge bridge-name ctx-name}

1.35.1   Purpose

Displays the bridge forwarding table for one or more bridges that know the specified medium access control (MAC) address.

1.35.2   Command Mode

All modes

1.35.3   Syntax Description

mac-addr

MAC address for which the bridge forwarding table is to be displayed, in the format hh:hh:hh:hh:hh:hh.

all

Displays the bridge forwarding table for all bridges in all contexts that know the specified MAC address.

bridge

Displays the bridge forwarding table for the specified bridge.

bridge-name

Name of the bridge with the bridge forwarding table to be displayed.

ctx-name

Name of the context in which the bridge exists.

1.35.4   Default

None

1.35.5   Usage Guidelines

Use the show bridge table mac-entry command to display the bridge forwarding table for one or more bridges that know the specified MAC address.

Use the show bridge bridge-name ctx-name construct to display the bridge forwarding table for that bridge.

Use the all keyword to display the bridge forwarding tables for all bridges in all contexts that know the specified MAC address.

Note:  
By default, most show commands (in any mode) display information for the current context only or, depending on the command syntax, for all contexts. If you are an administrator for the local context, you can insert the optional context ctx-name construct, preceding the show command, to view output for the specified context without entering that context. For more information about using the context ctx-name construct, see the context command description.

Note:  
By appending a space followed by the pipe ( | ) character at the end of a show command, you can filter the output using a set of modifier keywords and arguments. For more information, see Modifying Output of show Commands in Using the CLI.

1.35.6   Examples

The following example displays the bridge forwarding table for the bridges that know the MAC address, 00:50:04:73:30:2e:

[local]Redback>show bridge table mac-entry 00:50:04:73:30:2e
Context          Bridge Group     MAC               Circuit         

c1               b2               00:50:04:73:30:2e 2/6 vpi-vci 1 33

c2               b3               00:50:04:73:30:2e 4/9             



Static MAC = 0, Dynamic MAC = 2, Drop MAC = 0, Multicast = 0

1.36   show bridge table type

show bridge table type [bridge bridge-name ctx-name [detail] | all [detail] | entry-type [detail]]

1.36.1   Purpose

Displays the bridge forwarding table for one or more bridges.

1.36.2   Command Mode

All modes

1.36.3   Syntax Description

bridge

Optional. Displays the bridge forwarding table for the specified bridge.

bridge-name

Name of the bridge with the bridge forwarding table to be displayed.

ctx-name

Name of the context in which the bridge exists.

detail

Optional. Displays detailed information from the bridge forwarding table.

all

Optional. Displays the bridge forwarding table for all bridges in all contexts.

entry-type

Optional. Type of medium access control (MAC) address entry in the bridge forwarding table to be displayed, according to one or more of the following keywords:


  • drop—Specifies dropped MAC addresses.

  • duplicate—Specifies duplicated MAC addresses.

  • dynamic—Specifies learned MAC addresses.

  • static—Specifies configured MAC addresses.

  • trib—Specifies MAC addresses on tributary circuits.

  • trunk—Specifies MAC addresses on trunk circuits.

1.36.4   Default

Displays all types of MAC addresses for all bridge forwarding tables in the current context.

1.36.5   Usage Guidelines

Use the show bridge table type command to display the bridge forwarding table for one or more bridges.

Use the detail keyword to display additional information.

Use the all keyword to display the bridge forwarding tables for all bridges in all contexts.

You can enter one or more keywords for the entry-type argument.

Table 13 lists the fields that are displayed for each bridge; some fields are displayed only when the detail keyword is specified.

Table 13    Field Descriptions for the show bridge table type Command

Field

Field

Context

Context in which the bridge is configured.

Bridge Group

Name of the bridge.

MAC

MAC address of the type specified.

Circuit

Slot, port, circuit identifier (VLAN tag value) on which the MAC address appears.

Slot

Displayed with the detail keyword only.

Flag

Displayed with the detail keyword only. Describes the MAC address or circuit, according to one or more of the following conditions:


  • D—Dropped MAC address

  • d—Duplicate MAC address

  • I—Ignored for now, to be validated, and might be purged later

  • i—Invalid MAC address

  • S—Static MAC address

  • T—Trunk circuit

  • t—Tributary circuit

  • U—Unbound circuit

Note:  
By default, most show commands (in any mode) display information for the current context only or, depending on the command syntax, for all contexts. If you are an administrator for the local context, you can insert the optional context ctx-name construct, preceding the show command, to view output for the specified context without entering that context. For more information about using the context ctx-name construct, see the context command description.

Note:  
By appending a space followed by the pipe ( | ) character at the end of a show command, you can filter the output using a set of modifier keywords and arguments. For more information, see Modifying Output of show Commands in Using the CLI.

1.36.6   Examples

The following example displays the bridge forwarding table entries for tributary, trunk, dropped, and static MAC addresses:

[local]Redback#show bridge table type trib trunk drop static detail
Flags:(U)nbound,(D)rop,(S)tatic,(d)uplicate,(T)runk,(t)rib,(I)gnore,(i)nvalid

Context        Bridge Group   MAC              Circuit          Slot Flag

c1             b1             00:00:00:00:00:31 All circuits         DS-----

c1             b1             00:00:00:00:00:32 All circuits         DS-----

c1             b1             00:00:00:00:01:31 3/1                  ---t---

c1             b1             00:00:00:00:01:32 3/1                  ---t---

1.37   show bulkstats

show bulkstats policy {blkst_policy | ALL} [collection]

1.37.1   Purpose

Displays the bulk statistics (bulkstats) configuration information and data transfer statistics, or the contents of the current collection file that have not yet been successfully transferred to the receiver, for the specified bulkstats policy or for all policies.

1.37.2   Command Mode

All modes

1.37.3   Syntax Description

policy blkst_policy

Name of the bulkstats policy for which bulkstats configuration information and statistics are to be displayed.

policy ALL

Specifies that bulkstats configuration information and statistics are to be displayed for all policies.

collection

Optional. Specifies that the contents of the collection file for the specified policy in its current state is to be displayed, rather than the configuration.

1.37.4   Default

Displays bulkstats configuration information for the specified policy.

1.37.5   Usage Guidelines

Use the show bulkstats command to display the current bulkstats configuration information and statistics about the data transfer for the specified policy or for all policies, including:

Use the optional collection keyword to display the contents of the current bulkstats collection file. This can be useful in debugging schema definitions.

Note:  
The contents of a collection file for a policy can be viewed only when bulkstats collection for that policy is disabled.

For detailed information on setting up bulkstats, see Configuring Bulkstats.

1.37.6   Examples

The following example displays bulk statistics information:

[local]Redback>show bulkstats policy bulk
Primary receiver: 198.168.145.99 via ftp

Secondary receiver: 198.168.147.31 via ftp

Last successful transfer to 198.168.145.99 on WED JUN 29 14:55:03 2005

Transferred 1019 bytes into

"//snmp:30A8E9F5A5BD154@198.168.145.99/Bulkstats/whitney_161953"

Last transfer attempt: WED JUN 29 14:58:47 2005

Next transfer attempt: FRI JUL 01 09:06:58 2005

The following example displays the current collection file:

[local]Redback>show bulkstats policy bulk collection
enet0: (454) 0/0 (null) 4632 2a 36 1

atm50: (454) 5/0 (null) 0 0 0 0

atm51: (454) 5/1 (null) 0 0 0 0

1.38   show bypass

show bypass [group group-name] [summary] [down | up] [lg group-name | lg id id-num] [port-cir] [detail]

1.38.1   Purpose

Displays bypass information for one or more cross-connected circuits in the system.

1.38.2   Command Mode

All modes

1.38.3   Syntax Description

group group-name

Optional. Displays information for only the specified cross-connect group.

summary

Optional. Displays summary information for all circuits.

down

Optional. Displays information for only inactive circuits.

up

Optional. Displays information for only active circuits.

port-cir

Optional. Provides the port, slot, and circuit identifier arguments for cross-connected circuits and cross-connected link groups:


  • For cross-connected circuits:slot[/port [circuit-id [child-circuit-type]]]

  • For cross-connected link groups:circuit-id [child-circuit-type]

lg group-name

Optional. Specifies the name of an access link group.

lg id id-num

Optional. Specifies the ID of an access link group.

slot

Optional. Chassis slot number of a card with the port for which bypass information is displayed. If omitted, displays bypass information for all cross-connected circuits in the system.

port

Optional. Card port number of the port for which bypass information is displayed. If omitted, displays bypass information for all cross-connected circuits on the ports of the specified card.

circuit-id

Optional. Circuit identifier, according to one of the constructs listed in Table 14. If omitted, displays bypass information for all circuits on the specified port or link group.

child-circuit-type

Optional. Child circuit type, according to one of the following keywords:


  • ipv6oe—Specifies an IP Version 6 over Ethernet (IPv6oE)-encapsulated circuit.

  • pppoe—Specifies a Point-to-Point Protocol (PPP) over Ethernet (PPPoE)-encapsulated circuit.


If omitted, displays bypass information for all cross-connected child circuits on the specified circuit.

detail

Optional. Displays detailed information.

1.38.4   Default

Displays bypass information for all cross-connected circuits on all cards.

1.38.5   Usage Guidelines

Use the show bypass command to display bypass information for one or more cross-connected circuits in the system.

Note:  
The SmartEdge 100 router limits the value of the slot argument to 2.

Note:  
The value for the port argument on the SmartEdge 100 router depends on the MIC slot in which the MIC is installed.

Table 14 lists the values for the circuit-id argument.

Table 14    Values for the circuit-id Argument

Field

Field

vlan vlan-id

A filter that limits the command to a specified virtual LAN (VLAN) 802.1Q tunnel or PVC. The vlan-id argument is one of the following constructs:


  • pvc-vlan-id—VLAN tag value of a PVC that is not within an 802.1Q tunnel.

  • tunl-vlan-id—VLAN tag value of an 802.1Q tunnel.

  • tunl-vlan-id:pvc-vlan-id—VLAN tag value of an 802.1Q tunnel followed by the VLAN tag value for the PVC within the tunnel.


The range of values for any VLAN tag value is 1 to 4095.

vpi-vci vpi vci

Virtual path identifier (VPI) and virtual circuit identifier (VCI) for an Asynchronous Transfer Mode (ATM) permanent virtual circuit (PVC). The range of values is 0 to 255 and 1 to 65535, respectively.

If you specify the VLAN tag value for an 802.1Q tunnel, the output includes bypass information for all the PVCs within the tunnel.

Note:  
By default, most show commands (in any mode) display information for the current context only or, depending on the command syntax, for all contexts. If you are an administrator for the local context, you can insert the optional context ctx-name construct, preceding the show command, to view output for the specified context without entering that context. For more information about using the context ctx-name construct, see the context command description.

Note:  
By appending a space followed by the pipe ( | ) character at the end of a show command, you can filter the output using a set of modifier keywords and arguments. For more information, see Modifying Output of show Commands in Using the CLI.

1.38.6   Examples

The following example displays bypass information for all cross-connected multiprotocol circuits that are active:

[local]Redback>show bypass up
Circuit                State  XC Circuit             State 

2/1 vpi-vci 0 34 pppoe Up     2/2 vpi-vci 0 34 pppoe Up 

The following example displays cross-connect group information:

[local]Redback>show bypass group one
Circuit        State XC Circuit       State

4/1 vlan-id 32 Up    5/1 vpi-vci 1 32 Up

The following example displays bypass summary information:

[local]Redback>show bypass summary
Endpoints total: 5, Up: 3, Down: 2 

Crossconnects total: 2, Up: 1, Down: 1