COMMAND DESCRIPTION     21/190 82-CRA 119 1170/1-V1 Uen D    

Commands: show k through show m

© Ericsson AB 2009–2010. All rights reserved. No part of this document may be reproduced in any form without the written permission of the copyright owner.

Disclaimer

The contents of this document are subject to revision without notice due to continued progress in methodology, design and manufacturing. Ericsson shall have no liability for any error or damage of any kind resulting from the use of this document.

Trademark List

SmartEdge is a registered trademark of Telefonaktiebolaget LM Ericsson.
NetOp is a trademark of Telefonaktiebolaget LM Ericsson.

Contents

1Command Descriptions
1.1show key-chain
1.2show l2tp counters peer
1.3show l2tp global
1.4show l2tp group
1.5show l2tp peer
1.6show lacp actor
1.7show lacp counters
1.8show lacp lg-id
1.9show lacp lg-name
1.10show lacp partner
1.11show lacp system-id
1.12show ldp address
1.13show ldp binding
1.14show ldp debug-filter
1.15show ldp interface
1.16show ldp l2vpn fec
1.17show ldp neighbor
1.18show ldp summary
1.19show licenses
1.20show link-group
1.21show log
1.22show logging
1.23show macro
1.24show malicious-traffic
1.25show memory
1.26show mobile-ip
1.27show mobile-ip binding
1.28show mobile-ip binding pending
1.29show mobile-ip care-of-address
1.30show mobile-ip debug
1.31show mobile-ip dynamic-key
1.32show mobile-ip dynamic-tunnel-profile
1.33show mobile-ip foreign-agent-peer
1.34show mobile-ip home-agent-peer
1.35show mobile-ip interface
1.36show mobile-ip local-address
1.37show mobile-ip log
1.38show mobile-ip statistics tunnel
1.39show mobile-ip tunnel
1.40show mobile-ip visitor
1.41show mobile-ip visitor pending
1.42show mpls
1.43show mpls interface
1.44show mpls-static label-action
1.45show mpls-static lsp
1.46show msdp peer
1.47show msdp sa-cache
1.48show msdp summary


1   Command Descriptions

Commands starting with “show k” through commands starting “show m” are included.

1.1   show key-chain

show key-chain [summary] [key-chain-name]

1.1.1   Purpose

Displays information for key chains configured in the system.

1.1.2   Command Mode

all modes

1.1.3   Syntax Description

summary

Optional. Specifies that you want to display only summary information.

key-chain-name

Optional. Name of a specific key chain for which you want to display information.

1.1.4   Default

When entered without any optional syntax, the show key-chain command displays information for key chains configured in the system.

1.1.5   Usage Guidelines

Use the show key-chain command to display information for key chains configured in the system.

Note:  
By default, most show commands (in any mode) display information for the current context only or, depending on the command syntax, for all contexts. If you are an administrator for the local context, you can insert the optional context ctx-name construct, preceding the show command, to view output for the specified context without entering that context.

Note:  
By appending a space followed by the pipe ( | ) character at the end of a show command, you can filter the output using a set of modifier keywords and arguments. For more information, see Modifying Output of show Commands in the document, Using the CLI.

1.1.6   Examples

The following example displays information for all key chains:

[local]Redback>show key-chain



key-chain superkeychain: 

count: 1, sequences: 1 - 1, client count: 0 

modified: 00:00:04 (hh:mm:ss) ago 

key-id: 1 key-string encrypted: 38F24D69175F7C5548CB61C4D69E856A 

key-string unencrypted: password 

accept-lifetime start: 2000:01:01:00:00:00 end: infinite 

send-lifetime start: 2001:04:14:00:01:00 end: infinite 

key-chain se1400: 

count: 1, sequences: 1 - 1, client count: 0 

modified: 00:00:04 (hh:mm:ss) ago 

key-id: 1 key-string encrypted: 38F24D69175F7C5548CB61C4D69E856A 

key-string unencrypted: password 

accept-lifetime start: 2000:01:01:00:00:00 end: infinite 

send-lifetime start: 2001:04:14:00:01:00 end: infinite 

The following example displays summary information for the superkeychain key chain:

[local]Redback>show key-chain superkeychain summary

key-chain superkeychain: 

count: 1, sequences: 1 - 1, client count: 0 

modified: 00:00:07 (hh:mm:ss) ago 

1.2   show l2tp counters peer

show l2tp counters peer peer-name tunnel [tunl-id [detail]]

1.2.1   Purpose

Displays all statistics for tunnel-level control packet counters for all tunnels under specific Layer 2 Tunneling Protocol (L2TP) peers on the system.

1.2.2   Command Mode

all modes

1.2.3   Syntax Description

peer-name

Name of the peer for which tunnel-level L2TP control packet counters are to be displayed.

tunnel

Displays counters for all L2TP tunnels on the specified peer.

tunl-id

Identifier of a specific L2TP tunnel for which counters are to be displayed.

detail

Optional. Displays detailed counter information for the specified L2TP tunnel.

1.2.4   Default

Displays counters for all L2TP tunnels on the peer.

1.2.5   Usage Guidelines

Use the show l2tp counters peer peer-name tunnel command to display tunnel-level counters for L2TP control packets.

Use the tunnel tunl-id construct to display counters for a specific L2TP tunnel.

Use the detail keyword to display detailed information for each L2TP counter.

Use the optional tunnel tunl-id construct to display all statistics for tunnel-level control packet counters for all tunnels with a specific tunnel ID.

Note:  
By appending a space followed by the pipe ( | ) character at the end of a show command, you can filter the output using a set of modifier keywords and arguments. For more information, see Modifying Output of show Commands in the document, Using the CLI. For more information about this command, see the BRAS Troubleshooting Guide.

1.2.6   Examples

The following example displays counters for L2TP tunnel 28561:

[local]Redback> show l2tp counters peer local-lac tunnel 28561
Local ID:            28561          Remote ID:           30416

Local IP:            10.1.1.2       Remote IP:           10.1.1.1

Local Name:          local-lac      Remote Name:         local-lns

Session Count:       101            Active Sessions:     100

Total Est Sessions:  120            Total Fail Sessions: 2

Max Sessions Ever:   100

Uptime:              10 mins 0 secs



Control Statistics

Tx Control Packets:  165031         Rx Control Packets:  165031

Tx Control Bytes:    2862224        Rx Control Bytes:    3015284020

Tx Hello Packets:    234            Rx Hello Packets:    235

Ns:                  2445           Nr:                  2457

Tx Cwnd:             3              Remote Window Size:  10

Resend Q Size:       8              Unsent Q Size:       6

Max Resend Q Size:   8              Max Unsent Q Size:   8

Control Errors:      2

The following example displays extra detail for counters for L2TP tunnel 28561:

[local]Redback>show l2tp counters peer local-lac tunnel 28561 detail
Local ID:            28561          Remote ID:           30416

Local IP:            10.1.1.2       Remote IP:           10.1.1.1

Local Name:          local-lac      Remote Name:         local-lns

Session Count:       101            Active Sessions:     100

Total Est Sessions:  120            Total Fail Sessions: 2

Max Sessions Ever:   100

Uptime :             50 mins 2 secs



Control Statistics

Tx Control Packets:  165031         Rx Control Packets:  165031

Tx Control Bytes:    2862224        Rx Control Bytes:    3015284020

Tx Hello Packets:    234            Rx Hello Packets:    235

Ns:                  2445           Nr:                  2457

Tx Cwnd:             3              Remote Window Size:  10

Resend Q Size:       8              Unsent Q Size:       6

Max Resend Q Size:   8              Max Unsent Q Size:   8

Control Errors:      2
Control Message Times

Last Msg sent:       Tue 16:34:06 (9 mins 19 secs ago)

Last Msg recved:     Tue 16:34:06 (9 mins 19 secs ago)

Last Hello sent:     Tue 16:34:06 (9 mins 19 secs ago)

Last Hello rcvd:     Tue 16:34:06 (9 mins 19 secs ago)

Last Control Error:  Tue 16:34:06 (9 mins 19 secs ago)

Data Statistics

Tx Data Packets:     4              Rx Data Packets:     3

Tx Data Bytes:       43             Rx Data Bytes:       36

1.3   show l2tp global

show l2tp global ipc

1.3.1   Purpose

Displays Layer 2 Tunneling Protocol (L2TP) interprocess communication (IPC) counters.

1.3.2   Command Mode

all modes

1.3.3   Syntax Description

ipc

Specifies the IPC counters.

1.3.4   Default

Displays IPC counters for all contexts.

1.3.5   Usage Guidelines

Use the show l2tp global command to view IPC counters for all L2TP peers and groups.

Note:  
By default, most show commands (in any mode) display information for the current context only or, depending on the command syntax, for all contexts. If you are an administrator for the local context, you can insert the optional context ctx-name construct, preceding the show command, to view output for the specified context without entering that context.

Note:  
By appending a space followed by the pipe ( | ) character at the end of a show command, you can filter the output using a set of modifier keywords and arguments. For more information, see Modifying Output of show Commands in the document, Using the CLI. For more information about this command, see the BRAS Troubleshooting Guide.

1.3.6   Examples

The following example displays the IPC counters for 16,000 subscriber circuits on each of two traffic cards in slots 12 and 13:

[local]Redback>show l2tp global ipc
L2TP IPC Stats



Up since:............Fri 08:13:05 (3 hours 30 mins 25 secs ago)

 Last clock tick:.....Fri 11:43:30 (0 secs ago)



ISM MBE:

  Sessions Recovered/Failed:......0/0

  Tunnels Recovered/Failed:.......0/0

  Idle Session Cleanups:..........0

  Couldn't Allocate Msg:..........0

  TX Circuit Tunnel-Start:........91867

  TX Circuit Tunnel-Stop:.........0

  TX Circuit Stale Kills:.........0

  TX Sub-Sess-Down:...............26

  Tunnel Start/Stop Errors:.......0



 PPP:

  RX Start request:...............0



 AAA:

  TX Tunnel Author:...............0

  RX Tunnel Author:...............0



 PPAs:

  Registrations:..................12

  Stale Registrations:............0

  Registration Errors:............0

  TX Tunnel Create:...............16179

  TX Tunnel Delete:...............95

  IPC Errors:.....................0



  Registered PPAs:



Slot 01 02 03 04 05 06 07 08 09 10 11 12 13 14

      I  I  I  I  .  .  .  .  .  .  .  I  I  .

      E  E  E  E  .  .  .  .  .  .  .  E  E  .



 PPA Name     Registration Time    Chg#  Ccts  Tun-Cr   Tun-Del

 ------------ -------------------- ----- ----- -------- --------

 Slot  1 IPPA Fri Nov 05 08:13:39      2     1    16179       95

 Slot  1 EPPA Fri Nov 05 08:13:40      4     1    16179       95

 Slot  2 IPPA Fri Nov 05 08:13:41      6     2    16179       95

 Slot  2 EPPA Fri Nov 05 08:13:42     16     2    16179       95

 Slot  3 IPPA Fri Nov 05 08:13:41      8     4    16179       95

 Slot  3 EPPA Fri Nov 05 08:13:42     18     4    16179       95

 Slot  4 IPPA Fri Nov 05 08:13:41     10     0    16179       95

 Slot  4 EPPA Fri Nov 05 08:13:42     20     0    16179       95

 Slot 12 IPPA Fri Nov 05 08:13:41     12 16004    16179       95

 Slot 12 EPPA Fri Nov 05 08:13:42     22 16004    16179       95

 Slot 13 IPPA Fri Nov 05 08:13:42     14 16002    16179       95

 Slot 13 EPPA Fri Nov 05 08:13:42     24 16002    16179       95

1.4   show l2tp group

show l2tp group [group-name]

1.4.1   Purpose

Displays Layer 2 Tunneling Protocol (L2TP) group configuration information.

1.4.2   Command Mode

all modes

1.4.3   Syntax Description

group-name

Optional. Name of an L2TP group or its domain alias to be displayed.

1.4.4   Default

Displays all L2TP groups in the current context.

1.4.5   Usage Guidelines

Use the show l2tp group command to view the redundancy algorithm and deadtime of one specific L2TP group or for all groups in the current context. When you display information for a specific group, the names of the peer members of the group and information about each peer are also displayed (see examples).

Note:  
By default, most show commands (in any mode) display information for the current context only or, depending on the command syntax, for all contexts. If you are an administrator for the local context, you can insert the optional context ctx-name construct, preceding the show command, to view output for the specified context without entering that context.

Note:  
By appending a space followed by the pipe ( | ) character at the end of a show command, you can filter the output using a set of modifier keywords and arguments. For more information, see Modifying Output of show Commands in the document, Using the CLI. For more information about this command, see the BRAS Troubleshooting Guide.

1.4.6   Examples

The following example displays output from the show l2tp group command without specifying a group name:

[local]Redback>show l2tp group 
Group Name       Algorithm    Deadtime 

---------------- ------------ -------- 

l2tp             Load-balance 10

l2tp2            Load-balance 5

l2tp3            Load-balance 10

The following example displays the output when you use the show l2tp group command to display a particular group (l2tp). The asterisk (*) in front of the peer, l2tp-1, indicates that the peer is down (“dead”). For more information about this status, see the deadtime command (in L2TP group configuration mode) in the Configuring L2TP document:

[local]Redback#show l2tp group l2tp
Group name:      l2tp  RADIUS:  YES 
Algorithm        Load-balance  Deadtime: 10 
Peers:          *l2tp-1
                 l2tp-2 

Domains: vpn 
                            Max  Tun     Max   Ses 
Peer Name  Local Name Med  Tuns  Cnt    Ses   Cnt Stat  LAC  LNS  Named
--------- ----------  ---   ----  ---  ---   ---- ----  ---  ---  -----
l2tp-1     tgrp1       UDP   1     0     20     0   NO    YES  YES   YES
l2tp-2     tgrp2       UDP   1     1     65535  6   NO    YES  YES   YES

1.5   show l2tp peer

show l2tp peer [peer-name [tunnel [tunl-num [session [ses-num]]]]]

1.5.1   Purpose

Displays a summary of status and configuration for Layer 2 Tunneling Protocol (L2TP) peers.

1.5.2   Command Mode

all modes

1.5.3   Syntax Description

peer-name

Optional. Name of the L2TP peer or its domain alias for which you want detailed information displayed.

tunnel

Optional if you use the peer-name argument. Displays detailed information for the tunnels configured to the specified peer.

tunl-num

Optional if you use the tunnel keyword. Numeric tunnel ID for the tunnel for which you want detailed information displayed.

session

Optional if you use the tunnel tunl-num construct. Displays detailed information for the sessions configured on the specified tunnel.

ses-num

Optional if you use the session keyword. Numeric session ID for the session for which you want detailed information displayed.

1.5.4   Default

Displays all peers in the current context.

1.5.5   Usage Guidelines

Use the show l2tp peer command without any optional syntax to display the L2TP summary information for each L2TP peer; see Table 1. For more information about this command, see the BRAS Troubleshooting Guide.

Table 1    Field Descriptions for the show l2tp peer Command

Field

Description

Peer Name

L2TP peer name

Local Name

Local name for SmartEdge router in outbound Start-Control-Connection-Request (SCCRQ) control messages

Tun Cnt

Number of tunnels (in any state) to the peer

Ses Cnt

Number of sessions (in any state) to the peer

Use the optional peer-name argument to display the information shown in Table 2.

Table 2    Field Descriptions for the show l2tp peer Command for a Specific Peer

Field

Description

Peer name

Name of the peer you specified.

Local Name

Local name for SmartEdge router in outbound SCCRQ control messages as specified by the local-name command (in L2TP peer configuration mode).

Media

Tunnel encapsulation type (UDP).

Local IP Address

Local IP address of the peer as entered in the l2tp-peer name command (in context configuration mode).

Remote IP Address

For each tunnel, the remote IP address.

LAC

Indicates whether the peer performs LAC functions.

LNS

Indicates whether the peer performs LNS functions.

RADIUS

Indicates whether the peer is served by the Remote Authentication Dial-In User Service (RADIUS).

Static

YES—Tunnel is maintained to the peer at all times.


NO—Tunnels are established on demand.

DNIS

Indicates whether DNIS-based tunnel switching is enabled.

DNIS ONLY

Indicates whether DNIS attribute must be present on an incoming session for the sessions to be accepted.

Unnamed

Indicates whether the peer is unnamed (Unnamed=YES) or named (Unnamed=NO). If Unnamed=YES, the peer name displayed was automatically obtained from the remote host name contained in the incoming SCCRQ.

Hello Timer

Value of the interval SmartEdge router waits before sending an L2TP Hello packet if there has been no exchange of control messages to the remote L2TP peer.

Maximum Tunnels

Maximum number of tunnels allowed to the peer.

Maximum Ses/Tunnel

Maximum number of sessions allowed for each tunnel.

Control Timeout

Number of seconds to wait for an acknowledgment before a control message is retransmitted.

Retry

Number of control message retransmissions.

Tunnel Count

Number of tunnels (any state) to the peer.

Session Count

Number of sessions (any state) to the peer, all tunnels combined.

Domains

Domain aliases specified with the domain command (in L2TP peer configuration mode).

Use the optional tunnel tunl-num construct to display information shown in Table 3; if you enter the tunnel keyword without the tunl-num argument, the command displays information for all tunnels configured to the peer.

Table 3    Field Descriptions for the show l2tp peer Command for Tunnels

Field

Description

State

State of the tunnel.

Last change

Time the last change to the tunnel occurred and the elapsed time.

Local ID

Local tunnel ID.

Remote ID

Remote tunnel ID.

Local IP

Local IP address of the peer.

Remote IP

Remote IP address of the peer.

Local Name

Local name for SmartEdge router in outbound Start-Control-Connection-Request (SCCRQ) control messages as specified by the local-name command (in L2TP peer configuration mode).

Remote Name

Remote name of the peer.

Session Count

Number of sessions in this tunnel—cumulative since the tunnel came up.

Active Sessions

Number of current sessions in the established state in the tunnel.

Total Act Sessions

Number of sessions that reached the established state in this tunnel—cumulative since the tunnel came up.

Total Fail Session

Number of sessions that failed to reach the established state in this tunnel—cumulative since the tunnel came up.

Window current-tx

Control message activity; current outbound transmissions.

max-tx

Control message activity; maximum transmissions.

rx

Control message activity; current inbound transmissions.

Tunnel PPA Table

List of slot numbers (1 to 14 for SmartEdge 800 router, 1 to 6 for SmartEdge 400 router); an “I” marks slots with cards being used for inbound transmissions; an “E” marks slots with cards being used for outbound transmissions.

Use the optional session ses-num construct to display the information shown in Table 4; if you enter the session keyword without the ses-num argument, the information displays for all sessions configured on the tunnel.

Table 4    Field Descriptions for the show l2tp peer Command for Sessions

Field

Description

State

State of the session.

Last change

Time the last change to the session occurred and the elapsed time.

Port/Circuit

Slot and port numbers, virtual path and circuit identifiers.

Local ID

Local session number.

Remote ID

Remote session number.

Tx Data Packets

Number of data packets transmitted during the session.

Rx Data Packets

Number of data packets received during the session.

Tx Data Bytes

Number of data bytes transmitted during the session.

Rx Data Bytes

Number of data bytes received during the session.

Note:  
By default, most show commands (in any mode) display information for the current context only or, depending on the command syntax, for all contexts. If you are an administrator for the local context, you can insert the optional context ctx-name construct, preceding the show command, to view output for the specified context without entering that context.

Note:  
By appending a space followed by the pipe ( | ) character at the end of a show command, you can filter the output using a set of modifier keywords and arguments. For more information, see Modifying Output of show Commands in the document, Using the CLI. For information about troubleshooting L2TP, see the BRAS Troubleshooting Guide.

1.5.6   Examples

The following example displays output of the show l2tp peer command without any optional constructs:

[local]Redback>show l2tp peer
                                           Tun   Ses 
Peer Name            Local Name            Cnt   Cnt 
-------------------- -------------------- ----- -----
dnslns1              dnslac1                  1     1
snap                 dnslac1                  0     0

The following example displays output of the show l2tp peer command for a specific peer:

[local]Redback>show l2tp peer dnslns1 

Peer Name:           dnslns1            
Local Name:          dnslac1        Vendor:              Redback Networks
Local IP Address:    10.13.49.208   Remote IP Address:   10.13.16.3    
Local Role:          LAC Only       DNIS:                Disabled      
Hello Timer:         300            Preference:          10            
Maximum Tunnels:     32767          Maximum Ses/Tunnel:  8             
Control Timeout:     15             Retry:               6             
Tunnel Count:        1              Session Count:       1 
Domains:             lns1dns1.net

The following example displays the output when you enter the show l2tp peer command and specify a peer name and tunnel ID:

[local]Redback>show l2tp peer dnslns1 tunnel 5080
State:               Established
Last change:         Tue 12:10:58 (12 secs ago)
Local ID:            5080           Remote ID:           57620
Local IP:            10.13.49.208   Remote IP:           10.13.16.3
Local Name:          dnslac1        Remote Name:         dnslns1
Session Count:       0              Active Sessions:     0
Total Act Sessions:  0              Total Fail Session:  0

Control Channel:
Window current-tx: 10 max-tx: 10 rx: 8

Tunnel PPA Table:
Slot 01 02 03 04 05 06 07 08 09 10 11 12 13 14
      I  .  .  .  .  .  .  .  .  .  .  .  .  .
      E  .  .  .  .  .  .  .  .  .  .  .  .  .

The following example displays the output when you use the show l2tp peer command naming a specific peer with tunnel and session IDs:

[local]Redback>show l2tp peer dnslns1 tunnel 43023 session 57155
State:               Established
Last change:         Fri 07:02:58 (2 hours 27 mins 22 secs ago)
Port/Circuit:        1/2 vpi-vci 0 448
Local ID:            57155          Remote ID:           52763

Network Statistics
Tx Data Packets:     2915           Rx Data Packets:     0
Tx Data Bytes:       58348          Rx Data Bytes:       0

1.6   show lacp actor

show lacp actor [circuit circuit] [detail]

1.6.1   Purpose

Displays the actor information for all the Link Aggregation Control Protocol (LACP) circuits or the LACP circuit with a specified circuit handle.

1.6.2   Command Mode

all modes

1.6.3   Syntax Description

circuit circuit

Optional. LACP circuit for which actor information is displayed.

details

Optional. Displays additional details for each LACP circuit.

1.6.4   Default

When you enter this command without an optional keyword or argument, it displays a brief summary of all LACP circuits.

1.6.5   Usage Guidelines

Use the show lacp actor command to display the actor information of all the LACP circuits.

Use the circuit circuit construct to display the actor information associated with the LACP port circuit.

Use the detail keyword to display the additional details of the LACP actor information.

Note:  
By appending a space followed by the pipe ( | ) character at the end of a show command, you can filter the output using a set of modifier keywords and arguments. For more information, see Modifying Output of show Commands in the document, Using the CLI.

1.6.6   Examples

The following example shows how to display a list of LACP actor information:

[local]Redback#sh lacp actor

                Port   Port         Oper   Recv          Seln

Lg-id   Port   State   Priority     key    State         State

----------------------------------------------------------------------

26      5/3    0x3c    32767        5      exchg         active

26      5/5    0x4     32767        5      exchg         actor-stdby

26      5/7    0x4     32767        5      exchg         actor-stdby

27      5/4    0x3d    32767        6      exchg         active

27      5/6    0xd     32767        6      exchg         partner-stdby

27      5/8    0xd     32767        6      exchg         partner-stdby

The following example shows how to display a detailed list of LACP actor information:

[local]Redback#show lacp actor detail

Internal Handle : 5/3:1023:63/1/1/5

Circuit State   : UP

Mac Address     : 00:30:88:00:12:86

1.7   show lacp counters

show lacp counters

1.7.1   Purpose

Displays the counters for all Link Aggregation Control Protocol (LACP) links on the system.

1.7.2   Command Mode

all modes

1.7.3   Syntax Description

This command has no keywords or arguments.

1.7.4   Default

When you enter this command, it displays the counters for all LACP circuits on the system.

1.7.5   Usage Guidelines

Use the show lacp counters command to display all LACP circuit counters on the system.

Note:  
By appending a space followed by the pipe ( | ) character at the end of a show command, you can filter the output using a set of modifier keywords and arguments. For more information, see Modifying Output of show Commands in the document, Using the CLI.

1.7.6   Examples

The following example shows how to display a list of link group counters on the system:

[local]Redback>show lacp counters



Internal Handle : 5/3:1023:63/1/1/5

Recvd Pkts  : 473         Sent Pkts   : 473         Recvd Bad   : 0



Internal Handle : 5/5:1023:63/1/1/9

Recvd Pkts  : 475         Sent Pkts   : 474         Recvd Bad   : 0



Internal Handle : 5/7:1023:63/1/1/13

Recvd Pkts  : 475         Sent Pkts   : 475         Recvd Bad   : 0

1.8   show lacp lg-id

show lacp lg-id id [detail]

1.8.1   Purpose

Displays the information for the Link Aggregation Control Protocol (LACP) link group with a given identification number.

1.8.2   Command Mode

all modes

1.8.3   Syntax Description

id

Link group ID for which LACP information is displayed; the range of values is 1 to 10000.

detail

Optional. Displays additional details for the specified LACP link group ID.

1.8.4   Default

When you enter this command without an optional keyword or argument, it displays a brief summary for the LACP link group with a given identification number.

1.8.5   Usage Guidelines

Use the show lacp lg-id command to display the information for the LACP link group with a given identification number.

Note:  
By appending a space followed by the pipe ( | ) character at the end of a show command, you can filter the output using a set of modifier keywords and arguments. For more information, see Modifying Output of show Commands in the document, Using the CLI.

1.8.6   Examples

The following example shows how to display a brief summary of the specified LACP link group 26:

[local]Redback>show lacp lg-id
[local]Redback#show lacp lg-id 26

Internal Handle     : 255/6:1023:63/1/1/2

Link-group ID       : 26

Link-group Name     : foo

LACP Mode           : PASSIVE

Admin Key           : 5

Revertible          : NO

Min-Links           : 2

Max-Links           : 1

Total Grp Links     : 3

Active Links        : 1

Standby Links       : 2

Actor-Stdby Links   : 2

Partner-Stdby Links : 0

Both-Stdby Links    : 0

Force-Revert Links  : 0

Lg-flags            : 0x4

1.9   show lacp lg-name

show lacp lg-name name [detail]

1.9.1   Purpose

Displays the Link Aggregation Control Protocol (LACP) information for link group with the specified name.

1.9.2   Command Mode

all modes

1.9.3   Syntax Description

name

Link group for which LAPC information is displayed.

detail

Optional. Displays additional details for the specified link group.

1.9.4   Default

When you enter this command without an optional keyword or argument, it displays a brief summary for the LACP link group with a given name.

1.9.5   Usage Guidelines

Use the show lacp lg-name command to display the LACP information for the link group with the specified name.

Note:  
By appending a space followed by the pipe ( | ) character at the end of a show command, you can filter the output using a set of modifier keywords and arguments. For more information, see Modifying Output of show Commands in the document, Using the CLI.

1.9.6   Examples

The following example shows how to display the LACP information for link group foo:

[local]Redback#show lacp lg-name foo detail

Internal Handle     : 255/6:1023:63/1/1/2

Link-group ID       : 26

Link-group Name     : foo

LACP Mode           : PASSIVE

Admin Key           : 5

Revertible          : NO

Min-Links           : 2

Max-Links           : 1

Total Grp Links     : 3

Active Links        : 1

Standby Links       : 2

Actor-Stdby Links   : 2

Partner-Stdby Links : 0

Both-Stdby Links    : 0

Force-Revert Links  : 0

Lg-flags            : 0x4

1.10   show lacp partner

show lacp partner [circuit circuit] [detail]

1.10.1   Purpose

Displays the partner information for all the Link Aggregation Control Protocol (LACP) circuits or the LACP circuit with a specified circuit handle.

1.10.2   Command Mode

all modes

1.10.3   Syntax Description

circuit circuit

LACP circuit for which the partner information is displayed.

detail

Optional. Displays additional details for each LACP circuit.

1.10.4   Default

When you enter this command without an optional keyword or argument, it displays a brief summary of all LACP circuits.

1.10.5   Usage Guidelines

Use the show lacp partner command to display the partner information of the LACP circuits.

Use the circuit circuit construct to display the partner information associated with the LACP port circuit.

Use the detail keyword to display the additional details of the LACP partner information.

Note:  
By appending a space followed by the pipe ( | ) character at the end of a show command, you can filter the output using a set of modifier keywords and arguments. For more information, see Modifying Output of show Commands in the document, Using the CLI.

1.10.6   Examples

The following example shows how to display a summary of link groups:

[local]Redback>show lacp partner
Actor           Partner   Port      Port          Oper

Lg-id   Port    Port      State     Priority      key

------------------------------------------------------------

26       5/3    0x403     0x3d      32767         6

26       5/5    0x405     0xd       32767         6

27       5/4    0x402     0x3c      32767         5

27       5/6    0x404     0x4       32767         5

1.11   show lacp system-id

show lacp system-id

1.11.1   Purpose

Displays the Link Aggregation Control Protocol (LACP) system ID for the SmartEdge router on the system.

1.11.2   Command Mode

all modes

1.11.3   Syntax Description

This command has no keywords or arguments.

1.11.4   Default

When you enter this command, it displays the LACP system information for the SmartEdge router.

1.11.5   Usage Guidelines

Use the show lacp system-id command to display LACP system information for the SmartEdge router.

Note:  
By appending a space followed by the pipe ( | ) character at the end of a show command, you can filter the output using a set of modifier keywords and arguments. For more information, see Modifying Output of show Commands in the document, Using the CLI.

1.11.6   Examples

The following example shows how to display LACP system ID for the SmartEdge router:

[local]Redback>show lacp system-id



System Priority : 2

System MAC      : 00:30:88:00:09:84

1.12   show ldp address

show ldp address

1.12.1   Purpose

Displays Label Distribution Protocol (LDP) interface IP address to label-switched router (LSR) ID mappings.

1.12.2   Command Mode

all modes

1.12.3   Syntax Description

This command has no keywords or arguments.

1.12.4   Default

None

1.12.5   Usage Guidelines

Use the show ldp address command to display LDP interface IP address to LSR ID mappings.

Note:  
By default, most show commands (in any mode) display information for the current context only or, depending on the command syntax, for all contexts. If you are an administrator for the local context, you can insert the optional context ctx-name construct, preceding the show command, to view output for the specified context without entering that context.

Note:  
By appending a space followed by the pipe ( | ) character at the end of a show command, you can filter the output using a set of modifier keywords and arguments. For more information, see Modifying Output of show Commands in the document, Using the CLI. For information about how to troubleshoot LDP signaling, see the MPLS Troubleshooting document.

1.12.6   Examples

The following example displays LDP interface IP address information:

[local]Redback>show ldp address
Flags - (S - Stale)
Address         RemoteLSRId           #Path Flag
10.12.210.37    local                 1         
172.16.1.1      local                 1 

1.13   show ldp binding

show ldp binding [hexadecimal] [detail]

1.13.1   Purpose

Displays Label Distribution Protocol (LDP) label binding information.

1.13.2   Command Mode

all modes

1.13.3   Syntax Description

hexadecimal

Optional. Displays label binding information in hexadecimal format.

detail

Optional. Displays detailed information.

1.13.4   Default

None

1.13.5   Usage Guidelines

Use the show ldp binding to display LDP label binding information.

Note:  
By default, most show commands (in any mode) display information for the current context only or, depending on the command syntax, for all contexts. If you are an administrator for the local context, you can insert the optional context ctx-name construct, preceding the show command, to view output for the specified context without entering that context.

Note:  
By appending a space followed by the pipe ( | ) character at the end of a show command, you can filter the output using a set of modifier keywords and arguments. For more information, see Modifying Output of show Commands in the document, Using the CLI. For information about how to troubleshoot LDP signaling, see the MPLS Troubleshooting document.

1.13.6   Examples

The following example displays LDP label binding information:

[local]Redback>show ldp binding
> active binding, Local/In - local/input label binding
 From - source of remote label, Remote/Out - remote/output label binding
  Prefix/FEC         Learned-From          Local/In   Remote/Out Interface
> 10.12.11.0/24      local                 3
  10.13.49.0/24      10.14.210.2:0         524293     3
                     10.14.200.2:0                    3
> 10.14.6.0/24       10.14.200.2:0         524296     3          to_edge_10/11
> 10.14.7.0/24       10.14.200.2:0         524297     3          to_edge_10/11
  10.14.10.0/24      10.14.200.2:0         524298     3
> 10.14.30.0/24      local                 3
                     10.14.210.2:0                    3
> 10.14.31.0/24      local                 3
                     10.14.210.2:0                    3
> 10.14.37.0/24      local                 3
                     10.14.200.2:0                    3
> 10.14.38.0/24      10.14.200.2:0         524299     3          to_edge_10/11
> 10.14.39.0/24      10.14.200.2:0         524300     3          to_edge_10/11
> 10.14.100.0/30     10.14.200.2:0         524301     3          to_edge_10/11
  10.14.101.0/30     10.14.200.2:0         524302     3
> 10.14.200.2/32     10.14.200.2:0         524303     3          to_edge_10/11
> 10.14.210.1/32     local                 3
> 10.14.210.2/32     10.14.210.2:0         524294     3          to_core_10/1
>                                                                to_metro_9/2
  192.168.1.0/24     10.14.210.2:0         524295     3

The following example displays detailed LDP label binding information:

[local]pearl#show ldp binding detail

 > active binding, Local/In - local/input label binding
 From - source of remote label, Remote/Out - remote/output label binding
 PathFlags -    (A - Active Path, B - Best path, H - Host, R - Redistributed
                 P - Path stale, U - Suppressed by in-bound policy), L - LSP-TE
 NextHopFlags - (S - Nexthop stale, L - LDP eligible, N - Nexthop active
                 D - Nexthop Deleted, Y - Bypass in use)
 PrefixFlags -  (C - Local label active, M - LSP in LM, W - Label map in LM
                 G - Label reused, O - Change LM, T - Change update)
   Prefix/FEC    Learned-From   Local/In   Remote/Out  Interface  NextHop    IntfGrid #P #N FecF NhF PathF Metric   AltAdjId BPassLbl

> 82.1.1.1/32    local          3                                            10000001 3  1  C    LN  ABR   0
                 83.1.1.1:0     524293                                       0
                 84.1.1.1:0     524293                                       0
> 83.1.1.1/32    83.1.1.1:0     524290     3           to-foo     10.1.1.2   10000003 2  1  MWOL LN  BL    2        0
>                83.1.1.1:0                3                      83.1.1.1   0                       BL    0        9300013
                 84.1.1.1:0     524294                                       0
> 84.1.1.1/32    84.1.1.1:0     524288     3           to-bar     21.1.1.2   10000002 2  1  MWOL LN  BL    2        0
>                84.1.1.1:0                3                      84.1.1.1   0                       BL    0        9300010
                 83.1.1.1:0     524294                                       0
  195.1.1.0/24   84.1.1.1:0     524289     3                                          2  0           U     0
                 83.1.1.1:0                3                                                         U     0

1.14   show ldp debug-filter

show ldp debug-filter

1.14.1   Purpose

Displays any filters that may be currently enabled to control the generation of Label Distribution Protocol (LDP) debug messages.

1.14.2   Command Mode

all modes

1.14.3   Syntax Description

This command has no keywords or arguments.

1.14.4   Default

None

1.14.5   Usage Guidelines

Use the show ldp debug-filter command to display any filters that may be currently enabled to control the generation of LDP debug messages.

Filters can be enabled through the use of the debug ldp filter command (in exec mode).

Note:  
By default, most show commands (in any mode) display information for the current context only or, depending on the command syntax, for all contexts. If you are an administrator for the local context, you can insert the optional context ctx-name construct, preceding the show command, to view output for the specified context without entering that context.

Note:  
By appending a space followed by the pipe ( | ) character at the end of a show command, you can filter the output using a set of modifier keywords and arguments. For more information, see Modifying Output of show Commands in the document, Using the CLI. For information about how to troubleshoot LDP signaling, see the MPLS Troubleshooting document.

1.14.6   Examples

The following example displays the filters that are currently enabled to manage the generation of LDP debug messages:

[local]Redback>show ldp debug-filter
Debug filter enabled on context 40080001

Only display debug messages to and from neighbor 10.1.1.1

1.15   show ldp interface

show ldp interface [detail]

1.15.1   Purpose

Displays Label Distribution Protocol (LDP) interface information.

1.15.2   Command Mode

all modes

1.15.3   Syntax Description

detail

Optional. Displays detailed information.

1.15.4   Default

None

1.15.5   Usage Guidelines

Use the show ldp interface command to display LDP interface information.

Note:  
By default, most show commands (in any mode) display information for the current context only or, depending on the command syntax, for all contexts. If you are an administrator for the local context, you can insert the optional context ctx-name construct, preceding the show command, to view output for the specified context without entering that context.

Note:  
By appending a space followed by the pipe ( | ) character at the end of a show command, you can filter the output using a set of modifier keywords and arguments. For more information, see Modifying Output of show Commands in the document, Using the CLI. For information about how to troubleshoot LDP signaling, see the MPLS Troubleshooting document.

1.15.6   Examples

The following example displays LDP interface information:

[local]Redback>show ldp interface
Flag:
(B - Bound, U - Up, D - Deleted, S - Stale, E - Hold expired, T - Bind Stale
Interface            Local Addr            Flag  RemoteLSRId          HoldExpr
to_edge_10/11        10.14.37.1/24         BU    10.14.200.2:0        12
to_core_10/1         10.14.30.1/24         BU    10.14.210.2:0        11
to_metro_9/2         10.14.31.1/24         BU    10.14.210.2:0        11

1.16   show ldp l2vpn fec

show ldp l2vpn fec [detail | vc-id vc-id [detail]]

1.16.1   Purpose

Displays Layer 2 Virtual Private Network (L2VPN)-related information for Label Distribution Protocol (LDP) L2VPN cross-connections.

1.16.2   Command Mode

all modes

1.16.3   Syntax Description

detail

Optional. Displays detailed LDP L2VPN cross-connection information.

vc-id vc-id

Optional. Cross-connected circuit associated with the virtual circuit identifier (VCI) for which to display LDP L2VPN cross-connection information. The range of vc-id values is 0 to 4,294,967,295.

detail

Optional. Displays detailed LDP L2VPN cross-connection information only for the specified cross-connected circuit.

1.16.4   Default

None

1.16.5   Usage Guidelines

Use the show ldp l2vpn fec command to display L2VPN-related information for LDP L2VPN cross-connections.

Note:  
By default, most show commands (in any mode) display information for the current context only or, depending on the command syntax, for all contexts. If you are an administrator for the local context, you can insert the optional context ctx-name construct, preceding the show command, to view output for the specified context without entering that context.

Note:  
By appending a space followed by the pipe ( | ) character at the end of a show command, you can filter the output using a set of modifier keywords and arguments. For more information, see Modifying Output of show Commands in the document, Using the CLI.

1.16.6   Examples

The following example displays L2VPN-related information for LDP L2VPN cross-connections:

[local]Redback>show ldp l2vpn fec
Codes : GID - Group ID, F - Frame Relay, V - VLAN, E - Ether, A - ATM
L - Local, R - Remote, N - Negotiated
VC ID  VC Type  Peer            L-Label  R-Label  L-GID    R-GID    State
1      V        190.190.190.190 131072   0        0        0        L
50     E        190.190.190.190 131073   131073   0        0        LR

The following example displays detailed L2VPN-related information for LDP L2VPN cross-connections:

[local]Redback>show ldp l2vpn fec detail
Codes : GID - Group ID, F - Frame Relay, V - VLAN, E - Ether, A - ATM
L - Local, R - Remote, N - Negotiated
VC ID               : 1          VC Type        : V
Peer                : 190.190.190.190 State          : L
L-Label             : 131072     R-Label        : 0
L-GID               : 0          R-GID          : 0
L-VCCV-CC           : PWE3-Controlword,MPLS-RouterAlert-label
L-VCCV-CV           : LSP ping
R-VCCV-CC           : None
R-VCCV-CV           : None
N-VCCV-CC           : None
N-VCCV-CV           : LSP ping
Flags               : mtu-set, adv-peer, local: 0x2a
Old L-Label         : 0          Old R-Label    : 0
L-Label received    : Jan 1 01:20:37.131
L-Label advertised  : Jan 1 01:20:55.022
R-Label received    : Jan 1 00:00:00.000
R-Label sent        : Jan 1 00:00:00.000
VC ID               : 50         VC Type        : E
Peer                : 190.190.190.190 State          : LR
L-Label             : 131073     R-Label        : 131073
L-GID               : 0          R-GID          : 0
L-VCCV-CC           : PWE3-Controlword,MPLS-RouterAlert-label
L-VCCV-CV           : LSP ping
R-VCCV-CC           : PWE3-Controlword,MPLS-RouterAlert-label
R-VCCV-CV           : LSP ping
N-VCCV-CC           : PWE3-Controlword
N-VCCV-CV           : LSP ping
Flags               : mtu-set, adv-peer, local, remote
: 0x6a
Old L-Label         : 0          Old R-Label    : 0
L-Label received    : Jan 1 01:20:37.131
L-Label advertised  : Jan 1 01:21:04.392
R-Label received    : Jan 1 01:21:00.590
R-Label sent        : Jan 1 01:21:00.590

The following example displays L2VPN-related information for the LDP L2VPN cross-connection associated with the VCI 333:

[local]Redback>show ldp l2vpn fec vc-id 1
VC ID  VC Type  Peer            L-Label  R-Label  L-GID    R-GID    State
1      V        190.190.190.190 131072   0        0        0        L

The following example displays detailed L2VPN-related information for the LDP L2VPN cross-connection associated with the VCI, 333:

[local]Redback>show ldp l2vpn fec vc-id 1 detail

Codes : GID - Group ID, F - Frame Relay, V - VLAN, E - Ether, A - ATM
L - Local, R - Remote, N - Negotiated
VC ID               : 1          VC Type        : V
Peer                : 190.190.190.190 State          : L
L-Label             : 131072     R-Label        : 0
L-GID               : 0          R-GID          : 0
L-VCCV-CC           : PWE3-Controlword,MPLS-RouterAlert-label
L-VCCV-CV           : LSP ping
R-VCCV-CC           : None
R-VCCV-CV           : None
N-VCCV-CC           : None
N-VCCV-CV           : LSP ping
Flags               : mtu-set, adv-peer, local: 0x2a
Old L-Label         : 0          Old R-Label    : 0
L-Label received    : Jan 1 01:20:37.131
L-Label advertised  : Jan 1 01:20:55.022
R-Label received    : Jan 1 00:00:00.000
R-Label sent        : Jan 1 00:00:00.000

1.17   show ldp neighbor

show ldp neighbor [ip-addr] [detail]

1.17.1   Purpose

Displays Label Distribution Protocol (LDP) neighbor information.

1.17.2   Command Mode

all modes

1.17.3   Syntax Description

ip-addr

Optional. Neighbor IP address.

detail

Optional. Displays detailed information.

1.17.4   Default

Displays LDP information for all neighbors.

1.17.5   Usage Guidelines

Use the show ldp neighbor command to display LDP neighbor information.

If the LDP neighbor’s transport IP address differs from its router ID, the IP address specified in the neighbor ip-addr construct must be the LDP neighbor’s transport IP address.

Note:  
By default, most show commands (in any mode) display information for the current context only or, depending on the command syntax, for all contexts. If you are an administrator for the local context, you can insert the optional context ctx-name construct, preceding the show command, to view output for the specified context without entering that context.

Note:  
By appending a space followed by the pipe ( | ) character at the end of a show command, you can filter the output using a set of modifier keywords and arguments. For more information, see Modifying Output of show Commands in the document, Using the CLI. For information about how to troubleshoot LDP signaling, see the MPLS Troubleshooting document.

1.17.6   Examples

The following example displays summary LDP neighbor information:

[local]Redback>show ldp neighbor
PeerFlags: A - LocalActiveOpen, D - Deleted, R - Reseting, E - OpenExtraDelay
           N - OpenNoDelay, P - SetMD5Passwd, T - RetainRoute, F - FlushState
           X - ExplicitNullEnabled, C - ExplicitNullStatusChanging
           G - Graceful Restart Supported, L - Session Life Extended
SHld - Session Holdtime Left, HHld - Hello Holdtime Left

NeighborAddr    LDP Identifier        State   Flag SHld HHld Interface
3.3.3.3         3.3.3.3:0             Oper    AG   82   14   3/10

The following example displays detailed LDP neighbor information:

[local]Redback>show ldp neighbor detail
PeerFlags: A - LocalActiveOpen, D - Deleted, R - Reseting, E - OpenExtraDelay
           N - OpenNoDelay, P - SetMD5Passwd, T - RetainRoute, F - FlushState
           X - ExplicitNullEnabled, C - ExplicitNullStatusChanging
           G - Graceful Restart Supported, L - Session Life Extended
SHld - Session Holdtime Left, HHld - Hello Holdtime Left
Rcvd - Hello Holdtime Received, Used - Hello Holdtime Used
Left - Hello Holdtime Left, Intv - Hello Interval Used

Neighbor Address:    83.1.1.1                 State:             Oper
  LDP Identifier:    83.1.1.1:0               Flags:             GQ
  Last Reset Reason: LDP initialized          Error:
  Recv Notification: Success                  Sent Notification: Success
  FEC Ver:           8                        ADDR Ver:          4
  TCP Conn Local:    82.1.1.1/646             Remote:            83.1.1.1/61597
  Sess Hold Expire:  88                       Next KeepAlive:    29 sec
  Rcvd Reconn Time:  60                       Rcvd Recover Time: 150
  MsgRcvd:           61                       MsgSent:           60
  Up/Down Time Since Last Chg: 00:27:55       Reset Count:       0
  lsp egress: 83.1.1.1 adjid: 0x09300013      cct:               255/3:1023:63/0/1/4
  # of Adjacency:    2
  #   Interface             I/F Address     Rcvd Used Left Intv
  1 : to-hilljack           10.1.1.1/24     15   15   10   5
  2 : none - remote         none            45   45   42   15

1.18   show ldp summary

show ldp summary

1.18.1   Purpose

Displays a summary of Label Distribution Protocol (LDP) information.

1.18.2   Command Mode

all modes

1.18.3   Syntax Description

This command has no keywords or arguments.

1.18.4   Default

None

1.18.5   Usage Guidelines

Use the show ldp summary command to display a summary of LDP information.

Note:  
By default, most show commands (in any mode) display information for the current context only or, depending on the command syntax, for all contexts. If you are an administrator for the local context, you can insert the optional context ctx-name construct, preceding the show command, to view output for the specified context without entering that context. For more information about using the context ctx-name construct, see the context command description in the Command List.

By default, most show commands (in any mode) display information for the current context only or, depending on the command syntax, for all contexts. If you are an administrator for the local context, you can insert the optional context ctx-name construct, preceding the show command, to view output for the specified context without entering that context.


Note:  
By appending a space followed by the pipe ( | ) character at the end of a show command, you can filter the output using a set of modifier keywords and arguments. For more information, see Modifying Output of show Commands in the document, Using the CLI. For information about how to troubleshoot LDP signaling, see the MPLS Troubleshooting document.

1.18.6   Examples

The following example displays a summarization of LDP information:

[local]Redback>show ldp summary
LDP Identifier:        10.18.17.102:0        Config Trans Addr: None
FEC Version:           1                     ADDR Version:      1
Label Manager version: 0                     Operational Peers: 0
Recv Only Time Left:   6                     RestartCleanup In: 0     Sec
Labels Allocated:      1                     Router State: Converging
Graceful restart enabled, Fast-reroute disabled, Track-IGP-metric disabled, Create-LSP-Circuit disabled, use-te-lsp disabled, max-session 1100

1.19   show licenses

show licenses [all]

1.19.1   Purpose

Displays a list of software licenses and their configuration status.

1.19.2   Command Mode

1.19.3   Syntax Description

all

Optional. Displays the status of all licenses.

1.19.4   Default

Displays only configured licenses.

1.19.5   Usage Guidelines

Use the show licenses command to display a list of software licenses and their configuration status.

1.19.6   Examples

The following example displays configured software licenses:

 [local]Redback>show licenses



  Software Feature            License Configured

--------------------------    ------------------

l2tp all                            YES

subscriber active 8000              YES



 Total active subscriber license configured 8000 

The following example displays all software licenses and their configuration status:

[local]Redback>show licenses all



  Software Feature            License Configured

--------------------------    ------------------

subscriber dynamic-service          NO

l2tp all                            YES

mpls                                NO

subscriber high-availibility        NO

subscriber active 8000              YES

subscriber bandwidth                NO



 Total active subscriber license configured 8000 

1.20   show link-group

show link-group [group-name] [detail]

1.20.1   Purpose

Displays link groups, circuits, and bindings.

1.20.2   Command Mode

all modes

1.20.3   Syntax Description

group-name

Optional. Name of a link group.

detail

Optional. Displays detailed information.

1.20.4   Default

When you enter this command without any optional keyword or argument, it displays a brief summary of all link groups.

1.20.5   Usage Guidelines

Use the show link-group command to display link groups, circuits, and bindings.

Note:  
By default, most show commands (in any mode) display information for the current context only or, depending on the command syntax, for all contexts. If you are an administrator for the local context, you can insert the optional context ctx-name construct, preceding the show command, to view output for the specified context without entering that context.

Note:  
By appending a space followed by the pipe ( | ) character at the end of a show command, you can filter the output using a set of modifier keywords and arguments. For more information, see Modifying Output of show Commands in the document, Using the CLI.

1.20.6   Examples

Example 1:

The following example of the show link-group command shows how to display a brief summary of all link groups in the system. In the display, the Ccct count field provides the number of constituent circuits that make up a logical or aggregated circuit in the link group. Constituent circuits are the physical ports or channels in the link group bundle:

[local]Redback>show link-group

Linkgroup        ID    Group Type    Ccct   Bindings 
lg3              28    LS    mp       1      sn1@local 
lg4              29    LS    mp       1      sn2@local 

Example 2:

The following example of the show link-group command shows how to display information for the link group named lg3:

[local]Redback>show link-group lg3

Linkgroup        ID     Group Type     Ccct  Bindings
lg3              28     LS    mp       1     sn1@local

Example 3:

The following example of the show link-group command shows how to display detailed information for the link group named lg2. In the display, the Constituent Circuits field shows the status of three constituent Gigabit Ethernet ports that make up the link group.

Notice the link group ID is 27. The system automatically sets the link group ID value:

[local]Redback>show link-group lg2 detail
Link-Group: lg2, ID   : 27 , State : Up   
----------------------------------------------------------------------------
Ccct count      : 3                              Grouping     : LoadShare 
Card Type       : ether-10-port                  Type         : ether     
Bindings        : test@mt                        Minimum-links : 2
Maximum links   : 8
Mac Address     : 00:30:88:00:77:00
Internal Handle : 255/6:1023:63/1/1/4
Description
Constituent Circuits:
  1. 4/1 (Up)| 85%
  2. 3/1 (Up)| 55%
  3. 5/1 (Down)| 0%

The output line, 1. 4/1 (Up)|85%, shows that port 4/1 is up, sending packets at 85% of the port’s capacity. The next output line, 2. 3/1 (Up)|55%, shows that port 3/1 is up, sending packets at 55% of the port’s capacity. The final output line, 3. 5/1 (Down)|0%, shows that port 5/1 is down.

1.21   show log

show log [{active | file filename}] [{all | fac log-fac-name | tdm-console}][level level] [since start-time] [until end-time]

1.21.1   Purpose

Displays information about system event logs or a previously saved log file.

1.21.2   Command Mode

all modes

1.21.3   Syntax Description

active

Optional. Displays the system event log.

file filename

Optional. Log stored in the specified filename.

fac log-fac-name

Optional. Events for the specified facility. For the supported facilities, see Table 6.

tdm-console

Optional. Displays the tdm-console event log.

level level

Optional. Only events of the specified level or of higher severity are displayed. For the supported levels, see Table 5.

since start-time

Optional. Only events that happened after the specified time are displayed. This option is useful for viewing the last portion of a log. The start-time argument is in a yyyy:mm:dd:hh:mm[:ss] format, where:


  • yyyy = year

  • mm = month

  • dd = day

  • hh = hour

  • mm = minute

  • ss = optional second

until end-time

Optional. Only events that happened before the specified time are displayed. This option is useful for viewing the last portion of a log. The end-time argument is in a yyyy:mm:dd:hh:mm[:ss] format, where:


  • yyyy = year

  • mm = month

  • dd = day

  • hh = hour

  • mm = minute

  • ss = optional second

1.21.4   Default

None

1.21.5   Usage Guidelines

Use the show log command to display information about system event logs or a previously saved log file.

The tdm-console, since, until, and level keywords are only available after specifying the active keyword or the file filename construct.

The show log active command with the tdm-console keyword displays Field Programmable Gate Array (FPGA) mismatched log messages. For example, if you power on the system or perform a system or traffic card reload, and that card’s FPGA file revision and FPGA chip revision do not match, an FPGA mismatch log message is generated.

When you enter the reload command from the command-line interface (CLI), or a reboot command from the boot ROM, the system copies its log and debug buffers into these two special files: /md/loggd_dlog.bin and /md/loggd_ddbg.bin. As an aid to debugging, you can display these files using the show log command:

show log file /md/loggd_dlog.bin
show log file /md/loggd_ddbg.bin

Table 5 lists the possible values for the level argument.

Table 5    Keywords for Event Levels

Level

Description

emergency

Logs only emergency events

alert

Logs alert and more severe events

critical

Logs critical and more severe events

error

Logs error and more severe events

warning

Logs warning and more severe events

notice

Logs notice and more severe events

informational

Logs informational and more severe events

debug

Logs all events, including debug events

Table 6 lists the possible values for the fac-name argument.

Table 6    Keywords for Facility Names

Keyword

Facility

aaa

authentication, authorization, and accounting (AAA)

aos

AOS

arp

Address Resolution Protocol (ARP)

aspha

Advanced Services Processor (ASP) Home Agent (HA)

atm

Asynchronous Transfer Mode (ATM)

bgp

Border Gateway Protocol (BGP)

bprelay

bootp relay

ccth

Ccth cct handle lib

cfm

Ethernet connectivity fault management (CFM)

chunk

chunk library

cli

command-line interface (CLI)

clibe

CLI backend engine facility

clips

clientless IP service selection (CLIPS)

cls

classifier

csm

Controller State Manager (CSM)

cspf

constrained SPF

cxtmgr

Context Manager

dbs

DBS option

dhcp

DHCP Relay

dhcpv6

DHCPv6 Manager

dhelper

DHCP Helper

dhelper6

DHCPv6 Helper

dlm

Download Manager

dns

Domain Naming System (DNS)

dot1q

dot1q (1)

dpi

Advanced Services Engine (ASP) Deep Packet Inspection (DPI) Manager

dpmon

ASP DP inspection log

engine

ASE engine log facility

epsc-general

Evolved Packet System Control (EPSC) general

epsc-gtp

EPSC GPRS Tunneling Protocol (GTP)

epsc-pmip

EPSC Proxy Mobile IP (PMIP)

epsc-session

EPSC Session

epscsim

EPSC Simulator

evlog

Event Log

fast-restart

Fast Restart Library

flow

flow(2)

fm

Feature Manager

fpm

FPM Manager

fr

Frame Relay(3)

fsm

File Server Manager (FSM)

fsmbcsim

FSSB-C Simulator

gsmp

General Switch Management Protocol (GSMP)

halib

Home Agent (HA) PG library

hr

HTTP redirect

if

interface configuration

igmp

Internet Group Management Protocol (IGMP)

ike

ASE Internet Key Exchange (IKE) log

ipc

interprocess communication (IPC)

ipcpack

IPC-pack library

ipfix

rflow export facility

ipmul

IP Multicast

iprwlock

interprocess locks

ipsec

ASE Internet Protocol Security (IPSec) log

isis

Intermediate System-to-Intermediate System (ISIS)

ism

Interface and Circuit State Manager (ISM)

isp

ISP logging library

issu

In service software upgrade (ISSU)

l2tp

Layer 2 Tunneling Protocol (L2TP)

l2vpnmgr

Layer 2 Virtual Private Network (L2VPN) configuration

lacp

L2TP access concentrator (LAC) processor

ldp

Label Distribution Protocol (LDP)

lg

link group

lm

Label Manager

log

event logger

memmgr

Memory Manager

meta

META

mgd

Media Gateway daemon

mgmd

Media Gateway Manager

mip

Mobile IP

mipsim

Mobile IP simulator

mo

MO

momi

MOMI

mpls-static

Multiprotocol Label Switching (MPLS)-STATIC

mplsmgr

MPLS configuration

ms

MPLS Static

msdp

Multicast Search Discovery Protocol (MSDP)

mtrace

multicast trace route

nat

Network Address Translation (NAT)

nd

Neighbor Discovery (ND)

netdbginfra

Netdebug Infrastructure

netdbglib

Netdebug Library

netopd

NetOp daemon

ntp

Network Time Protocol (NTP)

odd

On Demand Diagnostics

ospf

Open Shortest Path First (OSPF)

ospf3

OSPFv3

pad

PA facility

pem

privacy-enhanced mail

pim

Protocol Independent Multicast (PIM)

pm

Process Manager (PM)

ppafwd

Packet Processing ASIC (PPA) forwarding infrastructure

ppainfra

PPA infrastructure

ppaip

PPA IP

ppal2

PPA layer 2

ppal4

PPA layer 4

ppalg

PPA link group

ppamedia

PPA media

ppampls

PPA Multiprotocol Label Switching (MPLS)

ppapedgr

PPA pedgraph

ppaplat

PPA platform

ppaqos

PPA quality of service (QoS)

pparedun

PPA redundancy

ppasub

PPA subscriber

ppp

Point-to-Point Protocol (PPP)

pppint

PPP internal

pppoe

PPP over Ethernet (PPPoE)

prefixlib

IPv6 prefix library

prp

ped rule parser

qos

QoS

rbos

RBOS

rcm

Router Configuration Manager (RCM)

rdb

redundant database

rib

Routing Information Base (RIB)

rip

Routing Information Protocol (RIP)

rpl

router policy library

rpm

Router Policy Manager (RPM)

rsdb

Runtime shared database (RSDB)

rsvp

Resource Reservation Protocol (RSVP)

rtdb

Run-time Database

sctp

Stream Control Transmission Protocol (SCTP)

security

Security facility

serlib

stream serializer library

sf

system function

sftp

Secure Shell FTP (SFTP) client

sftpd

SFTP server

shmlib

shared memory library

smr

Shared memory Routing Information Base (RIB)

sm-radix

Shared memory Radix facility

smrlib

Shared memory RIB library

snmp

Simple Network Management Protocol (SNMP)

ssh

Secure Shell (SSH)

sshd

SSH daemon

ssm

SSM facility

stat

statistics

static

static route

stp

Spanning Tree Protocol (STP)

sysmgr

System Manager

sysmon

system monitoring

sysstat

system status

tacplus

TACACS+

talk

talk

tasksrv

task services

throttle

throttle library

tunnel

tunnel

vlan

Virtual LAN (VLAN) ID

vrrp

Virtual Router Redundancy Protocol (VRRP)

xcd

Cross connect process daemon

xcdlib

Cross connect process library

(1)  The SmartEdge 100 router does not support 802.1Q.

(2)  Not all controller cards support flow.

(3)  The SmartEdge 100 router does not support Frame Relay.


Note:  
By default, most show commands (in any mode) display information for the current context only or, depending on the command syntax, for all contexts. If you are an administrator for the local context, you can insert the optional context ctx-name construct before the show command to view output for the specified context without entering that context. For more information about the context ctx-name construct, see the context command description.

Note:  
By appending a space followed by the pipe ( | ) character at the end of a show command, you can filter the output using a set of modifier keywords and arguments. For more information, see Modifying Output of show Commands in the document, Using the CLI.

1.21.6   Examples

The following example displays a partial listing of the active system event log:

[local]Redback>show log
Mar 10 21:25:25: %CSM-6-CARD: card oc3-8-port INSERTED in slot 1 READY
Mar 10 21:25:26: %CSM-6-CARD: card ch-ds3-12-port INSERTED in slot 2 READY
Mar 10 21:25:26: %CSM-6-CARD: card atm-ds3-12-port INSERTED in slot 3 READY
Mar 10 21:25:26: %CSM-6-PORT: pos 1/1 link state UP, admin is UP
Mar 10 21:25:26: %CSM-6-PORT: pos 1/2 link state UP, admin is UP
Mar 10 21:25:26: %CSM-6-PORT: pos 1/3 link state UP, admin is UP
Mar 10 21:25:26: %CSM-6-PORT: pos 1/4 link state UP, admin is UP
Mar 10 21:25:26: %CSM-6-PORT: channelized-ds3 2/1 link state UP, admin is UP
Mar 10 21:25:26: %CSM-6-PORT: ds1 2/1:1 link state UP, admin is UP
Mar 10 21:25:26: %CSM-6-PORT: ds1 2/1:5 link state UP, admin is UP
Mar 10 21:25:26: %CSM-6-PORT: ds1 2/1:6 link state UP, admin is UP
Mar 10 21:25:26: %CSM-6-PORT: ds1 2/1:7 link state UP, admin is UP
Mar 10 21:25:26: %CSM-6-PORT: ds1 2/1:8 link state UP, admin is UP
Mar 10 21:25:26: %CSM-6-PORT: ds1 2/1:15 link state UP, admin is UP
Mar 10 21:25:26: %CSM-6-PORT: ds1 2/1:16 link state UP, admin is UP
.....

The following example displays only that portion of the active log that was entered after 00:00 a.m. on March 20:

[local]Redback>show log active since 2005:03:20:00:00:00
Mar 20 01:16:15: %SYSLOG-6-INFO: ftpd[79]: connection from 127.0.2.5
Mar 20 01:16:16: %SYSLOG-6-INFO: ftpd[79]: FTP LOGIN FROM 127.0.2.5 as nobody
Mar 20 01:16:37: %SYSLOG-6-INFO: ftpd[79]: put /md/rcm_41.core = 9340060 bytes

1.22   show logging

show logging [buffer | filter]

1.22.1   Purpose

Displays system logger statistics, including logger uptime, number of logged messages, number of logged filter messages, and number of logged rate-limited messages.

1.22.2   Command Mode

all modes

1.22.3   Syntax Description

buffer

Optional. Displays the logging buffer information for each log filter type.

filter

Optional. Displays the filter logging level for each log filter type.

1.22.4   Default

None

1.22.5   Usage Guidelines

Use the show logging command to display statistics about the system logger, including logger uptime, number of logged messages, number of logged filter messages, and number of logged rate-limited messages.

Note:  
By default, most show commands (in any mode) display information for the current context only or, depending on the command syntax, for all contexts. If you are an administrator for the local context, you can insert the optional context ctx-name construct before the show command to view output for the specified context without entering that context. For more information about the context ctx-name construct, see the context command description.

Note:  
By appending a space followed by the pipe ( | ) character at the end of a show command, you can filter the output using a set of modifier keywords and arguments. For more information, see Modifying Output of show Commands in the document, Using the CLI.

1.22.6   Examples

The following example displays output from the show logging command:

[local]Redback>show logging
L% Logging Information

% ===================

%         Logger Uptime : 21:23:44 Mon Jun 27 2005

%    Logger Buffer (KB) : Log:        822, Dbg:       1024

%  Logger Buffer Locked : Log:          N, Dbg:          N

%          # Logged msg : Log:       2889, Dbg:          0

%     # Logged Filtered : Log:          0, Dbg:          0

% # Logged Rate Limited : Log:          0, Dbg:          0

%                ==================

%   Logger Drop Counter : All drop counters are all ZERO

The following example displays logging levels for each filter type:

[local]Redback>show logging filter
 Console priority critical (2)

 Monitor priority critical (2)

 File priority critical (2)

 Syslog priority critical (2)

1.23   show macro

show macro [command]

1.23.1   Purpose

Displays a list of command macros defined on the system.

1.23.2   Command Mode

1.23.3   Syntax Description

command

Optional. Displays the commands in the macros.

1.23.4   Default

Macros are listed without their commands.

1.23.5   Usage Guidelines

Use the show macro command to display a list of the command macros defined on the system. Macros are also displayed when you use the online Help; in this case, the macro name is indicated by the asterisk (*) character preceding it.

Use the command keyword to display the commands in each macro.

Note:  
By default, most show commands (in any mode) display information for the current context only or, depending on the command syntax, for all contexts. If you are an administrator for the local context, you can insert the optional context ctx-name construct before the show command to view output for the specified context without entering that context. For more information about the context ctx-name construct, see the context command description.

Note:  
By appending a space followed by the pipe ( | ) character at the end of a show command, you can filter the output using a set of modifier keywords and arguments. For more information, see Modifying Output of show Commands in the document, Using the CLI.

1.23.6   Examples

The following example displays the macros defined on the system:

[local]Redback>show macro
Macro            Mode              
show-all-port    inherit               
show-alot        inherit              

1.24   show malicious-traffic

show malicious-traffic [counters | log [file filename]]

1.24.1   Purpose

Displays malicious traffic information.

1.24.2   Command Mode

All modes

1.24.3   Syntax Description

counters

Displays malicious-traffic counter information.

log

Displays malicious-traffic log information.

log file filename

Displays malicious-traffic log information for a specified file. Specify the name of a file for which to display log information.

1.24.4   Default

None

1.24.5   Usage Guidelines

Use the show malicious-traffic command to display malicious traffic information.

Note:  
When using the show malicious-traffic file command from a non-local context, only files configured for that context can be viewed.

For information about detecting and monitoring malicious traffic, see Configuring Malicious Traffic Detection and Monitoring.

1.24.6   Examples

The following example displays output from the show malicious-traffic counters command from context configuration mode:

[local]Redback(config-ctx)#show malicious-traffic counters

Context Name        : local             Context ID          : 0x40080001
Alarm Raised        : N                 Next Counter Update : 0 secs.

Total Malicious Pkts: 10

Malformed-IP        : 10                Malformed-L4        : 0
 Invalid IP Length  : 10                 Invalid Checksum   : 0
 Invalid IP Checksum: 0                  Invalid L4 Length  : 0
 Invalid IP Version : 0
 Invalid IP Options : 0

Filtered            : 0                 Spoofed             : 0
 Filtered Drops     : 0                  RPF Failures       : 0
                                         Null Route         : 0

Reassembly          : 0                 Other               : 0
 Reassembly Failures: 0                  Realm Drops        : 0

The following example displays output from the show malicious-traffic log command:

Mar 16 18:05:43.000: [0001] [3/8:1023:63/1/1/20510] [inv ip vers] Length 252  00:00:0a:01:01:02 -> 00:30:8
8:12:78:ac (1500 00ee 0000 0000 4011 e3fb c001 0102 0500 0001)
Mar 16 18:05:43.000: [0001] [3/8:1023:63/1/1/20510] [inv ip vers] Length 252  00:00:0a:01:01:02 -> 00:30:8
8:12:78:ac (1500 00ee 0000 0000 4011 e3fb c001 0102 0500 0001)
Mar 16 18:05:43.000: [0001] [3/8:1023:63/1/1/20510] [inv ip vers] Length 252  00:00:0a:01:01:02 -> 00:30:8
8:12:78:ac (1500 00ee 0000 0000 4011 e3fb c001 0102 0500 0001)
Mar 16 18:05:43.000: [0001] [3/8:1023:63/1/1/20510] [inv ip vers] Length 252  00:00:0a:01:01:02 -> 00:30:8
8:12:78:ac (1500 00ee 0000 0000 4011 e3fb c001 0102 0500 0001)
Mar 16 18:05:43.000: [0001] [3/8:1023:63/1/1/20510] [inv ip vers] Length 252  00:00:0a:01:01:02 -> 00:30:8
8:12:78:ac (1500 00ee 0000 0000 4011 e3fb c001 0102 0500 0001)
Mar 16 18:05:43.000: [0001] [3/8:1023:63/1/1/20510] [inv ip vers] Length 252  00:00:0a:01:01:02 -> 00:30:8
8:12:78:ac (1500 00ee 0000 0000 4011 e3fb c001 0102 0500 0001)
Mar 16 18:05:43.000: [0001] [3/8:1023:63/1/1/20510] [inv ip vers] Length 252  00:00:0a:01:01:02 -> 00:30:8
8:12:78:ac (1500 00ee 0000 0000 4011 e3fb c001 0102 0500 0001)
Mar 16 18:05:43.000: [0001] [3/8:1023:63/1/1/20510] [inv ip vers] Length 252  00:00:0a:01:01:02 -> 00:30:8
8:12:78:ac (1500 00ee 0000 0000 4011 e3fb c001 0102 0500 0001)
Mar 16 18:05:43.000: [0001] [3/8:1023:63/1/1/20510] [inv ip vers] Length 252  00:00:0a:01:01:02 -> 00:30:8
8:12:78:ac (1500 00ee 0000 0000 4011 e3fb c001 0102 0500 0001)
Mar 16 18:05:43.000: [0001] [3/8:1023:63/1/1/20510] [inv ip vers] Length 252  00:00:0a:01:01:02 -> 00:30:8
8:12:78:ac (1500 00ee 0000 0000 4011 e3fb c001 0102 0500 0001)
Mar 16 18:05:43.000: [0001] [3/8:1023:63/1/1/20510] [inv ip vers] Length 252  00:00:0a:01:01:02 -> 00:30:8
8:12:78:ac (1500 00ee 0000 0000 4011 e3fb c001 0102 0500 0001)
Mar 16 18:05:43.000: [0001] [3/8:1023:63/1/1/20510] [inv ip vers] Length 252  00:00:0a:01:01:02 -> 00:30:8
8:12:78:ac (1500 00ee 0000 0000 4011 e3fb c001 0102 0500 0001)
Mar 16 18:05:43.000: [0001] [3/8:1023:63/1/1/20510] [inv ip vers] Length 252  00:00:0a:01:01:02 -> 00:30:8
8:12:78:ac (1500 00ee 0000 0000 4011 e3fb c001 0102 0500 0001)
Mar 16 18:05:43.000: [0001] [3/8:1023:63/1/1/20510] [inv ip vers] Length 252  00:00:0a:01:01:02 -> 00:30:8
8:12:78:ac (1500 00ee 0000 0000 4011 e3fb c001 0102 0500 0001)
Mar 16 18:05:43.000: [0001] [3/8:1023:63/1/1/20510] [inv ip vers] Length 252  00:00:0a:01:01:02 -> 00:30:8
8:12:78:ac (1500 00ee 0000 0000 4011 e3fb c001 0102 0500 0001)

1.25   show memory

show memory

1.25.1   Purpose

Displays system memory statistics.

1.25.2   Command Mode

all modes

1.25.3   Syntax Description

This command has no keywords or arguments.

1.25.4   Default

None

1.25.5   Usage Guidelines

Use the show memory command to display statistics about the available and allocated memory in the system memory partition, which is useful for determining if the system is running low on available memory.

Note:  
By default, most show commands (in any mode) display information for the current context only or, depending on the command syntax, for all contexts. If you are an administrator for the local context, you can insert the optional context ctx-name construct before the show command to view output for the specified context without entering that context. For more information about the context ctx-name construct, see the context command description.

Note:  
By appending a space followed by the pipe ( | ) character at the end of a show command, you can filter the output using a set of modifier keywords and arguments. For more information, see Modifying Output of show Commands in the document, Using the CLI.

1.25.6   Examples

The following example displays output from the show memory command:

[local]Redback>show memory
Memory:total 60556k, Used 22836k, Free 32660k 

1.26   show mobile-ip

show mobile-ip [all] [detail]

1.26.1   Purpose

Displays Mobile IP information for the foreign-agent (FA) or home-agent (HA) instances depending on the instance configured on the current context.

1.26.2   Command Mode

1.26.3   Syntax Description

all

Optional. Displays Mobile IP information for the FA and HA instances, including all error counters.

detail

Optional. Displays detailed Mobile IP information for the FA or HA instance in the current context.

1.26.4   Default

None

1.26.5   Usage Guidelines

Use the show mobile-ip command to display for the FA or HA instances in one or more contexts.

Note:  
By default, most show commands (in any mode) display information for the current context only or, depending on the command syntax, for all contexts. If you are an administrator for the local context, you can insert the optional context ctx-name construct, preceding the show command, to view output for the specified context without entering that context.

Note:  
By appending a space followed by the pipe ( | ) character at the end of a show command, you can filter the output using a set of modifier keywords and arguments. For more information, see Modifying Output of show Commands in the document, Using the CLI.

1.26.6   Examples

The following example shows how to display Mobile IP information for the local context:

[local]Redback>show mobile-ip

::::: Mobile IP Context : local  :::::



Home-Agent Service:

   Agent state               : Active

   Authentication            : DYNO-HMAC-MD5

   Key Derivation            : WiMAX HA Root Key

   Replay tolerance          : 7 seconds

   FA peer count             : 1

   REG max. lifetime         : 1800

   Dynamic Tunnel Profile    : Default

   Last Resort Interface     : subif

   Local Address(es):

      1.1.1.1

   Bindings registered: 0



::::: Mobile IP Global Error Counters :::::

     Invalid IP hdr        :  0              Invalid ICMP hdr      : 0

     Unknown Packets       :  0              Invalid pkt len       : 0

     Invalid TTL           :  0              Invalid ICMP chksum   : 0

     Invalid instance drops:  0              Invalid intf drops    : 0

     Invalid circuit drops :  0              Invalid context drops : 0

     Invalid L2 info drops :  0              Throttling drops      : 0

     Mgmt port UDP drops   :  0              Mgmt port ICMP drops  : 0

     Non-acc intf req drops:  0              No tunnel found drops : 0

     Dyn tnl bind I/F drops:  0

The following example shows how to display detailed Mobile IP information for the local context:

[local]Redback>show mobile-ip detail

::::: Mobile IP Context : local  :::::



Home-Agent Service:

   Agent state             : Active

   Authentication          : DYNO-HMAC-MD5

   Key Derivation          : WiMAX HA Root Key

   Replay tolerance        : 7 seconds

   FA peer count           : 1

   REG max. lifetime       : 1800

   Dynamic Tunnel Profile  : prof2

   Last Resort Interface   : subif

   Local Address(es):

      1.1.1.1

   Binding info

     Registered     : 0        Pending        : 0

   Registration Requests

     Received       : 1               Dropped        : 0

     New requests   : 0               Renewals       : 1

   Registration Replies

     Accepted       : 0               Rejected       : 0

   Deregistration Requests

     Received       : 0               Dropped        : 0

   Deregistration Replies

     Accepted       : 0               Rejected       : 0

   Registration Revocations

     Received       : 0               Sent           : 0

     Ack Received   : 0               Ack Sent       : 0

     Recv errors    : 0

   Registration request deny counters:

     Unspecified           : 0         Admin prohibited      : 0

     Insuff resource       : 0         MN-FA Auth failure    : 0

     ID Mismatch           : 0         FA-HA Auth failure    : 0

     Lifetime too long     : 0         Poorly formed req     : 0

     Encap unavailable     : 0         Missing NAI           : 0

     CVSEs from MN unsupptd: 0         NVSEs from MN ignored : 0

     CVSEs from FA unsupptd: 0         NVSEs from FA ignored : 0

   Registration Revocation deny counters:

     Poorly formed request : 0         Missing Home Address  : 0

     Bad Home Agent Addr   : 0         Bad Foreign Agent Addr: 0

     HA Role recv by HA    : 0         No FA-HA Auth Config  : 0

     FA-HA Auth Failure    : 0         Rev Replay Protect    : 0

     No Matching Binding   : 0         Binding HA Mismatch   : 0

     Binding CoA Mismatch  : 0         Rev Not Negotiated    : 0

   Registration Revocation Ack deny counters:

     Poorly formed reply   : 0         No FA-HA Auth Config  : 0

     FA-HA Auth Failure    : 0         No matching Rev Req   : 0

   AAA-AUTH Counters:

     New RRQ Auth Success  : 0         New RRQ Auth Failure  : 0

     Re-RRQ Auth Success   : 0         Re-RRQ Auth Failure   : 1

     De-RRQ Auth Success   : 0         De-RRQ Auth Failure   : 0

     Auth Resp Success     : 0         Auth Resp Failure     : 0

     Auth Resp TLV Error   : 0         Auth Resp Key Too Long: 0

     Pending Auth Req      : 0         Pending Session Down  : 0

     Session UP Sent       : 0         Session DOWN Sent     : 1

     Auth Req Sent         : 0         COA Resp Rcvd         : 0

     Auth Req Holdoff      : 0         Session UP Holdoff    : 0

     Session DOWN Holdoff  : 0         Auth Drop No NAI      : 0

   MIP Internal Counters:

     Reg Life-time-out     : 1         No Resource           : 0

     Home-Slot moves       : 0         NAI Collision         : 0

     Home-Slot MV RateLimt : 0         Sess Dwn No Home-Slot : 0

     Home-Slot Egress      : 0         Home-Slot Non-egress  : 0



::::: Mobile IP Global Error Counters :::::

     Invalid IP hdr        : 0         Invalid ICMP hdr      : 0

     Unknown Packets       : 0         Invalid pkt len       : 0

     Invalid TTL           : 0         Invalid ICMP chksum   : 0

     Invalid instance drops: 0         Invalid intf drops    : 0

     Invalid circuit drops : 0         Invalid context drops : 0

     Invalid L2 info drops : 0         Throttling drops      : 0

     Mgmt port UDP drops   : 0         Mgmt port ICMP drops  : 0

     Non-acc intf req drops: 0         No tunnel found drops : 0

     Dyn tnl bind I/F drops: 0

1.27   show mobile-ip binding

To display the bindings of a mobile node (MN) identified by its IP address in its home domain (HoA) use the following syntax:

show mobile-ip binding home-ip-addr

To display the bindings of an MN identified by its Network Access Identifier (NAI) use the following syntax:

show mobile-ip binding nai nai

To display the bindings of MNs without active sessions use the following syntax:

show mobile-ip binding no-session [detail]

To display the binding information of all mobile nodes (MNs) or just the MNs meeting some combination of local information; namely, the IP address of the home agent (HA), the IP address of the foreign agent (FA) peer, and the local circuit-handle use the following syntax:

show mobile-ip binding [local-address local-ip-addr] [{circuit circuit-handle} | {foreign-agent-peer fa-ip-addr}] [detail]

1.27.1   Purpose

Displays Mobile IP binding information.

1.27.2   Command Mode

1.27.3   Syntax Description

home-ip-addr

Displays the bindings information of an MN identified by its home domain IP address.

nai nai

Displays the bindings information of an MN identified by its NAI.

no-session

Displays the bindings information of MNs without active sessions.

local-address ip-addr

Displays the bindings information of an MN identified by the local IP address of its HA.

foreign-agent-peer fa-ip-addr

Displays the bindings information of an MN identified by the IP address of its FA.

circuit circuit-handle

Displays the bindings information of an MN identified by the local circuit handle.

detail

Displays detailed information.

1.27.4   Default

When entered without any optional syntax, the show mobile-ip binding command displays Mobile IP binding information for all FA peers for an HA instance.

1.27.5   Usage Guidelines

Use the show mobile-ip binding command to display Mobile IP binding.

Note:  
By default, most show commands (in any mode) display information for the current context only or, depending on the command syntax, for all contexts. If you are an administrator for the local context, you can insert the optional context ctx-name construct, preceding the show command, to view output for the specified context without entering that context.

Note:  
By appending a space followed by the pipe ( | ) character at the end of a show command, you can filter the output using a set of modifier keywords and arguments. For more information, see Modifying Output of show Commands in the document, Using the CLI.

1.27.6   Examples

The following example shows how to display Mobile IP bindings:

[local]Redback#show mobile-ip binding 
Binding         NAI (truncated)  Home Agent   Foreign Agent 
2.2.2.31        user1@rback      1.1.1.1      1.1.1.2

The following example shows how to display detailed Mobile IP bindings:

[local]Reback#show mobile-ip binding detail 
::::: Mobile IP Binding  16.1.1.3 :::::
   NAI            : Mobilesubs
   Home Agent     : 17.1.1.1         Foreign Agent   : 1.1.1.1
   FA Tunnel Cct  : ipip 23          FA Tunnel Intf : tun4
   Lifetime (secs): 1800             Rem lifetime   : 1167
   Up time        : 20:25:35         Registration Id: ca92d673.290025ae
   UDP port       : 434              Reg Flags      : ......T.
   Home Slot      : 3                Home Slot Moves: 0
   Re-Reg         : 45               CoA Moves      : 0
   Re-Reg-drops   : 0                Revocation     : Disabled
   Primary SPI    : 256
   Primary Key    : 0x61626162616261626162616261626162
   Bind Circuit   : 255/26:1023:63/11/1/8
   Tunnel Circuit : 255/24:1023:63/1/1/23

1.28   show mobile-ip binding pending

show mobile-ip binding pending [local-address local-ip-addr] [{circuit circuit-handle} | {foreign-agent-peer fa-ip-addr}] [detail]

1.28.1   Purpose

Displays the binding information of all mobile nodes (MNs) pending registration or just the pending MNs meeting some combination of local information; namely, the IP address of its home agent (HA), the IP address of its foreign agent (FA) peer, the local circuit-handle.

1.28.2   Command Mode

1.28.3   Syntax Description

local-address ip-addr

Displays the pending registration information of an MN identified by the local IP address of its HA.

foreign-agent-peer fa-ip-addr

Displays the pending registration information of an MN identified by the IP address of its FA.

circuit circuit-handle

Displays the pending registration information of an MN identified by the local circuit handle.

detail

Displays detailed information.

1.28.4   Default

When entered without any optional syntax, the show mobile-ip binding pending command displays Mobile IP pending visitor registration information for one or more FA peers and the HA instance.

1.28.5   Usage Guidelines

Use the show mobile-ip binding pending command to display Mobile IP pending registration information for a FA peer and HA instance

Note:  
By default, most show commands (in any mode) display information for the current context only or, depending on the command syntax, for all contexts. If you are an administrator for the local context, you can insert the optional context ctx-name construct, preceding the show command, to view output for the specified context without entering that context.

Note:  
By appending a space followed by the pipe ( | ) character at the end of a show command, you can filter the output using a set of modifier keywords and arguments. For more information, see Modifying Output of show Commands in the document, Using the CLI.

1.28.6   Examples

The following example shows how to display detailed Mobile IP pending visitor registration information:

[local]Redback#show mobile-ip binding pending detail



::::: Mobile IP Binding  0.0.0.0  :::::

   NAI            : user1@rbak

   Home Agent     : 17.1.1.1      Foreign Agent   : 1.1.1.1

   FA Tunnel Cct  : null 34       FA Tunnel Intf   : tun4

   Lifetime (secs): 1800          Rem lifetime   : 1782

   Up time        : 00:00:18      Registration Id: ca411676.470bfe48

   UDP port       : 0             Reg Flags      : ......T.

   Home Slot      : 1             Home Slot Moves: 0

   Re-Reg         : 0             CoA Moves      : 0

   Re-Reg-drops   : 0             Revocation     : Disabled

   Primary SPI    : 0

   Primary Key    :

   Bind Circuit   : 5/1:1:3/0/0/0

   Tunnel Circuit : 255/24:1023:63/1/1/34


The following example shows how to display Mobile IP pending visitor registration information:

[local]Redback#show mobile-ip binding pending



Binding   NAI (truncated)   Home Agent   Foreign Agent

0.0.0.0   user1@rbak        17.1.1.1     1.1.1.1

[local]Redback#

1.29   show mobile-ip care-of-address

show mobile-ip care-of-address [{if-name | detail}]

1.29.1   Purpose

Displays Mobile IP information for the care-of addresses (CoAs) for a foreign-agent (FA) instance.

1.29.2   Command Mode

1.29.3   Syntax Description

if-name

Optional. Displays Mobile IP CoA information for the specified CoA interface.

detail

Optional. Displays detailed Mobile IP CoA information.

1.29.4   Default

When entered without any optional syntax, the show mobile-ip care-of-address command displays CoA information for all CoAs for an FA instance.

1.29.5   Usage Guidelines

Use the show mobile-ip care-of-address command to display Mobile IP information for the CoA interfaces for an FA instance.

Note:  
By default, most show commands (in any mode) display information for the current context only or, depending on the command syntax, for all contexts. If you are an administrator for the local context, you can insert the optional context ctx-name construct, preceding the show command, to view output for the specified context without entering that context.

Note:  
By appending a space followed by the pipe ( | ) character at the end of a show command, you can filter the output using a set of modifier keywords and arguments. For more information, see Modifying Output of show Commands in the document, Using the CLI.

1.29.6   Examples

The following example shows how to display information for all CoAs for an FA instance:

[local]Redback>show mobile-ip care-of-address
Interface                            Care-of-Address       Status

home-agent-access                    14.1.1.1              Up

The following example shows how to display detailed information for all CoAs for an FA instance:

[local]Redback>show mobile-ip care-of-address detail
:::: Mobile IP CoA Interface : home-agent-access ::::

  CoA address    : 14.1.1.1          CoA Oper state : Up

  Circuit        : 3/4               Cct handle     : 3/4:1023:63/1/1/7

  Tunnels cnt    : 1                 Tunnels Up     : 1              

  Visitor cnt    : 1                 Pending cnt    : 0              

  State chg cnt  : 0 

1.30   show mobile-ip debug

show mobile-ip debug

1.30.1   Purpose

Displays the Mobile IP debug settings.

1.30.2   Command Mode

1.30.3   Syntax Description

This command has no keywords or arguments.

1.30.4   Default

None

1.30.5   Usage Guidelines

Use the show mobile-ip debug command to display the Mobile IP debug settings.

Note:  
By default, most show commands (in any mode) display information for the current context only or, depending on the command syntax, for all contexts. If you are an administrator for the local context, you can insert the optional context ctx-name construct, preceding the show command, to view output for the specified context without entering that context.

Note:  
By appending a space followed by the pipe ( | ) character at the end of a show command, you can filter the output using a set of modifier keywords and arguments. For more information, see Modifying Output of show Commands in the document, Using the CLI.

1.30.6   Examples

The following example shows how to enable the generation of debug messages for reg-request packets and then display the settings:

[local]Redback>debug mobile-ip packet type reg-request

[local]Redback>show mobile-ip debug 


:::: MIP Debug Types/Filters ::::

Type                     Filter

Packet Send              Type: Reg Request

Packet Receive           Type: Reg Request

1.31   show mobile-ip dynamic-key

show mobile-ip dynamic-key [all]

1.31.1   Purpose

For Mobile IP, displays WiMAX dynamic authentication keys used by an home-agent or foreign-agent instance.

1.31.2   Command Mode

1.31.3   Syntax Description

all

Optional. Displays information about WiMAX dynamic authentication keys derived from HA and FA instances for all contexts.

1.31.4   Default

When entered without any optional syntax, the show mobile-ip dynamic-key command, displays WiMAX dynamic authentication key information derived from an HA or FA instance within a context.

1.31.5   Usage Guidelines

Use the show mobile-ip dynamic key command to display WiMAX dynamic authentication keys derived from an HA or FA instance.

Note:  
By default, most show commands (in any mode) display information for the current context only or, depending on the command syntax, for all contexts. If you are an administrator for the local context, you can insert the optional context ctx-name construct, preceding the show command, to view output for the specified context without entering that context.

Note:  
By appending a space followed by the pipe ( | ) character at the end of a show command, you can filter the output using a set of modifier keywords and arguments. For more information, see Modifying Output of show Commands in the document, Using the CLI.

1.31.6   Examples

The following example shows how to display information about WiMAX dynamic authentication keys for the HA and FA instance in all contexts:

[local]Redback>show mobile-ip dynamic-keys all

::: Home Agent : local                Dynamic Keys   : wimax :::

SPI            : 270                  Time Remaining : 00:01:18 

Care-of-Addr   : 1.1.1.2              Home-Agent     : 1.1.1.1 

Key (hex)      : E845BC8929D45AF0FB546B1E864D8222FCA236D8



::: Foreign Agent : fa-ctx Dynamic Keys : wimax proprietary :::

SPI            : 271                  Time Remaining : 01:39:38

Care-of-Addr   : 1.1.1.2              Home-Agent     : 1.1.1.1 

Key (hex)      : E845BC8929D45AF0FB546B1E864D8222FCA236D8

SPI            : 270                  Time Remaining : 01:39:38 

Care-of-Addr   : 1.1.1.2              Home-Agent     : 1.1.1.1

Key (hex)      : E845BC8929D45AF0FB546B1E864D8222FCA236D8

The following example shows how to display information about WiMAX dynamic authentication keys from the HA instance:

[local]Redback>show mobile-ip dynamic-keys

::: Home Agent : local                Dynamic Keys   : wimax :::

SPI            : 270                  Time Remaining : 00:01:18 

Care-of-Addr   : 1.1.1.2              Home-Agent     : 1.1.1.1 

Key (hex)      : E845BC8929D45AF0FB546B1E864D8222FCA236D8


1.32   show mobile-ip dynamic-tunnel-profile

show mobile-ip dynamic-tunnel-profile [ profile-name] [detail]

1.32.1   Purpose

Displays information about dynamic tunnel profiles in that context.

1.32.2   Command Mode

1.32.3   Syntax Description

profile-name

Optional. Name of a dynamic tunnel profile.

detail

Optional. Displays detailed information about all Mobile IP dynamic tunnel profiles.

1.32.4   Default

When entered without any optional syntax, the show mobile-ip dynamic-tunnel-profile command displays all dynamic tunnels within a context and their status (in use or not in use).

1.32.5   Usage Guidelines

Use the show mobile-ip dynamic-tunnel-profile command to display information about a specific dynamic tunnel profile. Use the optional profile-name argument to display information about a specific dynamic tunnel profile.

Note:  
By default, most show commands (in any mode) display information for the current context only or, depending on the command syntax, for all contexts. If you are an administrator for the local context, you can insert the optional context ctx-name construct, preceding the show command, to view output for the specified context without entering that context.

Note:  
By appending a space followed by the pipe ( | ) character at the end of a show command, you can filter the output using a set of modifier keywords and arguments. For more information, see Modifying Output of show Commands in the document, Using the CLI .

1.32.6   Examples

The following example shows how to display the state for all dynamic tunnel profiles:

[local]Redback>show mobile-ip dynamic-tunnel-profile 
::::: Mobile IP Dynamic Tunnel Profiles :::::

     Profile            Status

     prof1              In-use           

     prof2              Not-in-use

The following example shows how to display detailed information for all dynamic tunnel profiles :

[local]Redback>show mobile-ip dynamic-tunnel-profile detail

::::: Mobile IP Dynamic Tunnel Profile: prof1 :::::

     Status             : In-use       Clear-DF       : Set

     Hold-time (secs)   : 60           Timeout (secs) : 10

     GRE MTU            : 1468         IPIP MTU:      : 1200

    


::::: Mobile IP Dynamic Tunnel Profile: prof2 :::::

     Status             : In-use       Clear-DF       : Not-Set

     Hold-time (secs)   : 60           Timeout (secs) : 10

     GRE MTU            : 1468         IPIP MTU:      : 1480

The following example shows how to display information about dynamic tunnel profile prof1:

[local]Redback>show mobile-ip dynamic-tunnel-profile prof1

::::: Mobile IP Dynamic Tunnel Profile: prof1 :::::

     Status:    In-use :                Clear-DF       : Set

     Hold-time (secs)  : 60             Timeout (secs) : 10

     GRE MTU           : 1468           IPIP MTU:      : 1200

     

1.33   show mobile-ip foreign-agent-peer

show mobile-ip foreign-agent-peer [ip-addr] | [detail]

1.33.1   Purpose

Displays information for one or all foreign-agent (FA) peers for a home-agent (HA) instance.

1.33.2   Command Mode

1.33.3   Syntax Description

ip-addr

Optional. IP address for the FA peer to be displayed.

detail

Optional. Displays detailed Mobile IP FA peer information.

1.33.4   Default

When entered without any optional syntax, the show mobile-ip foreign-agent-peer command displays information for all FA peers.

1.33.5   Usage Guidelines

Use the show mobile-ip foreign-agent-peer command to display information for one or all FA peers for an HA instance. The display includes information for all tunnels to the FA peers.

Note:  
By default, most show commands (in any mode) display information for the current context only or, depending on the command syntax, for all contexts. If you are an administrator for the local context, you can insert the optional context ctx-name construct, preceding the show command, to view output for the specified context without entering that context.

Note:  
By appending a space followed by the pipe ( | ) character at the end of a show command, you can filter the output using a set of modifier keywords and arguments. For more information, see Modifying Output of show Commands in the document, Using the CLI.

1.33.6   Examples

The following example shows how to display Mobile IP FA peer information for an home-agent (HA) instance:

[local]Redback>show mobile-ip foreign-agent-peer


Foreign-Agent   Bindings     Pending   Tnls  (Up)   State
1.1.1.2         429          0         1     (1 )   Active

The following example shows how to display detailed Mobile IP FA peer information for an home-agent (HA) instance:

[local]Redback>show mobile-ip foreign-agent-peer detail


::::: Mobile IP Foreign Agent Peer: 1.1.1.2  :::::
   Agent state    : Active          Tunnel cnt (Up): 1 (1)
   Binding cnt    : 0               Pending cnt    : 0
   Authentication : DYNO-HMAC-MD5   Key Derivation : WiMAX HA Root Key
   Type           : Static
   Dynamic Tunnel Profile  : Default
   Last Resort Interface   : None
   Registration Requests
     Received       : 3               Dropped        : 0
     New requests   : 3               Renewals       : 0
   Registration Replies
     Accepted       : 1               Rejected       : 1
   Deregistration Requests
     Received       : 0               Dropped        : 0
     Deregistration Replies
     Accepted       : 0               Rejected       : 0
   Registration Revocations
     Received       : 0               Sent           : 0
     Ack Received   : 0               Ack Sent       : 0
     Recv errors    : 0 Tunnel: IPIP 4  ( Intf: @ )    Tnl dest (CoA)   : 1.1.1.2         Tnl src (HA)   : 1.1.1.1@local    Admin state      : Up                Oper State   : Up
   Cct state        : Up                Cct handle   : 255/24:1023:63/0/1/4    Binding count    : 0                 Home Slot Mask  : 0x01
   Agent state     : Active             Tunnel cnt (Up): 1 (1) 

1.34   show mobile-ip home-agent-peer

show mobile-ip home-agent-peer [ip-addr] | [detail]

1.34.1   Purpose

Displays Mobile IP information for one or all home-agent (HA) peers for a foreign-agent (FA) instance.

1.34.2   Command Mode

1.34.3   Syntax Description

ip-addr

Optional. IP address for an HA peer to be displayed.

detail

Optional. Displays detailed Mobile IP HA peer information.

1.34.4   Default

When entered without any optional syntax, the show mobile-ip home-agent-peer command displays Mobile IP HA information for all HA peers for an FA instance.

1.34.5   Usage Guidelines

Use the show mobile-ip home-agent-peer command to display Mobile IP information for one or all HA peers for an FA instance. The display includes information for all tunnels to the HA peers.

Note:  
By default, most show commands (in any mode) display information for the current context only or, depending on the command syntax, for all contexts. If you are an administrator for the local context, you can insert the optional context ctx-name construct, preceding the show command, to view output for the specified context without entering that context.

Note:  
By appending a space followed by the pipe ( | ) character at the end of a show command, you can filter the output using a set of modifier keywords and arguments. For more information, see Modifying Output of show Commands in the document, Using the CLI.

1.34.6   Examples

The following example shows how to display Mobile IP HA peer information for all HA peers:

[local]Redback>show mobile-ip home-agent-peer

Home-Agent       Visitors Pending  Tnls (Up)  State    
14.1.1.2         1        0        2    (1 )  Active

The following example shows how to display detailed Mobile IP HA peer information for all HA peers:

[local]Redback>show mobile-ip home-agent-peer detail

::::: Mobile IP Home Agent Peer: 1.1.1.1  :::::    Agent state: Active     Tunnel cnt (Up): 2 (1) 
   VPN context id          : 0x40080004      context name   : fa-ctx
   Visitors cnt            : 0               Pending cnt    : 0 
   Authentication          : DYNO-HMAC-MD5   Key Derivation : WiMAX Proprietary
   Type           : Static
   Dynamic Tunnel Profile  : Default
   Last Resort Interface   : None
   Last Resort Interface   : None  
   Registration Requests
     Received       : 4               Relayed        : 3 
     New requests   : 4               Renewals       : 0 
     Dropped        : 0
   Registration Replies
     Received       : 2               Relayed        : 1 
     Total sent     : 0               Recv errors    : 0 
   Deregistration Requests      Received       : 0               Relayed        : 0 
     Dropped        : 0
   Deregistration Replies
     Received       : 0               Relayed        : 0 
     Total sent     : 0               Recv errors    : 0 
   Registration Revocations
     Received       : 0               Sent           : 0 
     Ack Received   : 0               Ack Sent       : 0 
     Recv errors    : 0 

Tunnel: IPIP 3  ( Intf: ha-tnl-if@fa-ctx )
    Tnl dest (HA)  : 1.1.1.1          Tnl src (CoA)  : 1.1.1.2@fa-ctx
    Admin state    : Up               per State      : Up
    Cct state      : Up               Cct handle     : 255/24:1023:63/0/1/3
    Visitor count  : 0  
Tunnel: GRE 1  ( Intf:  )
    Tnl dest (HA)  : 1.1.1.1          Tnl src (CoA)  : 1.1.1.2@fa-ctx
    Admin state    : Up               Oper State     : Down
    Cct state      : Up               Cct handle     : 255/4:1023:63/0/1/1
    Visitor count  : 0 

1.35   show mobile-ip interface

show mobile-ip interface [if-name] | [detail]

1.35.1   Purpose

Displays information for one or all Mobile IP interfaces.

1.35.2   Command Mode

1.35.3   Syntax Description

if-name

Optional. Name of the interface for which Mobile IP information is displayed.

detail

Optional. Displays detailed Mobile IP interface information.

1.35.4   Default

When entered without any optional syntax, the show mobile-ip interface command displays information for all Mobile IP interfaces.

1.35.5   Usage Guidelines

Use the show mobile-ip interface command to display information for one or all Mobile IP interfaces.

Note:  
By default, most show commands (in any mode) display information for the current context only or, depending on the command syntax, for all contexts. If you are an administrator for the local context, you can insert the optional context ctx-name construct, preceding the show command, to view output for the specified context without entering that context.

Note:  
By appending a space followed by the pipe ( | ) character at the end of a show command, you can filter the output using a set of modifier keywords and arguments. For more information, see Modifying Output of show Commands in the document, Using the CLI.

1.35.6   Examples

The following example shows how to display information for all interfaces used by Mobile IP services:

[local]Redback>show mobile-ip interface



Interface       Circuit                Service Visitors Pndg State

foreign-sub     3/2                    FA      1        0    Up

The following example shows how to display detailed information for all interfaces:

[local]Redback>show mobile-ip interface detail
Mobile IP Interface : foreign-sub 

  Service type: FA                   Oper state     : Up             

  Circuit     : 3/2                  Cct handle     : 3/2:1023:63/1/1/3

  Cct state   : Up                   

  Visitor info

    Registered     : 1               Pending        : 0 

  Agent Advertisements

    Adv lifetime   : 1800            Reg Lifetime   : 1800 

    Min interval   : 450             Max interval   : 600 

    Seq number     : 172             Adv flags      : R..F.G.T.. 

    Elapsed time   : 00:06:42        Next adv (sec) : 96

    Sent           : 173             Sent on Solicit: 0 

    Sent Revocation: 0              

  Agent Solicitations

    Received       : 0               Recv errors    : 0 

  Registration Requests

    Received       : 800             Relayed        : 800 

    New requests   : 0               Renewals       : 0 

  Registration Replies

    Received       : 0               Relayed        : 800 

    Total sent     : 0               Recv errors    : 0 

  Registration Revocations

    Received       : 0               Sent           : 0 

    Ack Received   : 0               Ack Sent       : 0 

    Recv errors    : 0              

  IEEE LLC XID

    Received       : 0               Errors         : 0 

1.36   show mobile-ip local-address

show mobile-ip local-address [interface-name [context-name]] detail

1.36.1   Purpose

Displays home agent (HA) instance local address information for the specified interface or all local address interfaces.

1.36.2   Command Mode

1.36.3   Syntax Description

interface-name

Optional. Name of an interface to be displayed.

context-name

Optional. Name of a context to be displayed.

detail

Optional. Displays detailed local address information.

1.36.4   Default

When entered without any optional syntax, the show mobile-ip local-address command displays all local address interfaces for the HA instance.

1.36.5   Usage Guidelines

Use the show mobile-ip local-address command to display local address information for the specified interface or all local address interfaces for the HA instance.

Note:  
By default, most show commands (in any mode) display information for the current context only or, depending on the command syntax, for all contexts. If you are an administrator for the local context, you can insert the optional context ctx-name construct, preceding the show command, to view output for the specified context without entering that context.

Note:  
By appending a space followed by the pipe ( | ) character at the end of a show command, you can filter the output using a set of modifier keywords and arguments. For more information, see Modifying Output of show Commands in the document, Using the CLI.

1.36.6   Examples

The following example shows how to display information about the Mobile IP services local address for an HA instance:

[local]Redback#show mobile-ip local-address



Interface 		    Local-Address   Status

to_fa         1.1.1.1         Up

1.37   show mobile-ip log

show mobile-ip log [aaa [error | rx | tx] | [error | ism | rx | tx] | malformed]

1.37.1   Purpose

Displays log information for Interface and Circuit State Manager (ISM) events or malformed packets events. It also displays authentication, authorization, and accounting (AAA) events.

1.37.2   Command Mode

1.37.3   Syntax Description

aaa

Optional. Displays AAA log.

error

Optional. Displays errors that occurred when sending or receiving events between Mobile IP and an AAA server or a FA instance, a HA instance, and an ISM.

rx

Optional. Displays all events received from ISM or AAA.

tx

Optional. Displays all events sent to ISM or AAA.

ism

Optional. Displays ISM log.

malformed

Optional. Displays malformed packet log. The malformed packets are displayed in hexadecimal format.

1.37.4   Default

None

1.37.5   Usage Guidelines

Use the show mobile-ip log command to display logging information for AAA events, ISM events, or malformed packets events.

Note:  
By default, most show commands (in any mode) display information for the current context only or, depending on the command syntax, for all contexts. If you are an administrator for the local context, you can insert the optional context ctx-name construct, preceding the show command, to view output for the specified context without entering that context.

Note:  
By appending a space followed by the pipe ( | ) character at the end of a show command, you can filter the output using a set of modifier keywords and arguments. For more information, see Modifying Output of show Commands in the document, Using the CLI.

1.37.6   Examples

The following displays log information for AA:

[local]Redback#show mobile-ip log aaa

MIP AAA log messages (6 total entries):



    0:  Jul 6 10:57:42 MIP AAA TX, rc: 0



        MIP AAA Event: Verify Subscriber EOF, reason: 0

        cct_handle: Cct invalid, aaa_idx: 0

        IP Addr: 0.0.0.0, nai: None

        ctx id: 0x0



    1:  Jul 6 10:57:42 MIP AAA RX, rc: 0



        MIP AAA Event: Verify EOF, reason: 0

        cct_handle: Cct invalid, aaa_idx: 0

        IP Addr: 0.0.0.0, nai: None

        ctx id: 0x0, rcv_ctx_id: 0x0



    2:  Jul 6 10:58:31 MIP AAA TX, rc: 1



        MIP AAA Event: Auth Request , reason: 0

        cct_handle: 255/26:1023:63/11/1/1, aaa_idx: 0

        IP Addr: 0.0.0.0, nai: shah1

        ctx id: 0x40080001



    3:  Jul 6 10:58:31 MIP AAA RX, rc: 0



        MIP AAA Event: Auth Ok, reason: 0

        cct_handle: 255/26:1023:63/11/1/1, aaa_idx: 1610612755

        IP Addr: 2.2.2.31, nai: shah1

        ctx id: 0x40080001, rcv_ctx_id: 0x40080001



    4:  Jul 6 10:58:31 MIP AAA TX, rc: 0



        MIP AAA Event: Session UP , reason: 0

        cct_handle: 255/26:1023:63/11/1/1, aaa_idx: 1610612755

        IP Addr: 0.0.0.0, nai: None

        ctx id: 0x0



    5:  Jul 6 11:02:40 MIP AAA TX, rc: 0



        MIP AAA Event: Session Down , reason: 0

        cct_handle: 255/26:1023:63/11/1/1, aaa_idx: 1610612755

        IP Addr: 0.0.0.0, nai: None

        ctx id: 0x40080001

1.38   show mobile-ip statistics tunnel

show mobile-ip statistics tunnel

1.38.1   Purpose

Displays statistics related to client interaction between Mobile IP and the tunnel manager.

1.38.2   Command Mode

1.38.3   Syntax Description

This command has no keywords or arguments.

1.38.4   Default

None

1.38.5   Usage Guidelines

Use the show mobile-ip statistics tunnel command to display statistics related to client interaction between Mobile IP and the tunnel manager in support of dynamic tunnel management. The statistics includes counters for messages and events related to dynamic tunnel creation, modification, and deletion.

Note:  
By default, most show commands (in any mode) display information for the current context only or, depending on the command syntax, for all contexts. If you are an administrator for the local context, you can insert the optional context ctx-name construct, preceding the show command, to view output for the specified context without entering that context.

Note:  
By appending a space followed by the pipe ( | ) character at the end of a show command, you can filter the output using a set of modifier keywords and arguments. For more information, see Modifying Output of show Commands in the document, Using the CLI.

1.38.6   Examples

The following example shows how to display statistics related to tunnel manager interaction in support of dynamic tunnel management:

[local]Redback>show mobile-ip statistics tunnel

Mobile IP tunnel statistics

IPC Msgs In              : 0         Reg Msgs Sent           : 3

Reg Msgs Send Failed     : 1         De-reg Msgs Sent        : 0

De-reg Msgs Send Failed  : 0         EOF Msgs Sent           : 2

EOF Msgs Send Failed     : 0         Tnl Add Msgs Sent       : 0

Tnl Add Msgs Send Failed : 0         Tnl Del Msgs Sent       : 0

Tnl Del Msgs Send Failed : 0         Tnl Set Msgs Sent       : 0

Tnl Set Msgs Send Failed : 0         Process Down            : 0

Process Up               : 1         Pending Events          : 0

Pending Tunnel Add       : 0

1.39   show mobile-ip tunnel

show mobile-ip tunnel [all-contexts] [static | dynamic] [details]

1.39.1   Purpose

Displays information about static and dynamic tunnels used for Mobile IP services.

1.39.2   Command Mode

1.39.3   Syntax Description

all-contexts

Optional. Display information about static and dynamic tunnels used for Mobile IP services in all contexts.

static

Optional. Display information about static tunnels used for Mobile IP services within a context.

dynamic

Optional. Display information about dynamic tunnels used for Mobile IP services within a context.

details

Optional. Display detailed information about static and dynamic tunnels used for Mobile IP services within a context.

1.39.4   Default

Displays information about static and dynamic tunnels for Mobile IP within a context.

1.39.5   Usage Guidelines

Use the show mobile-ip tunnel command to display information about static and dynamic tunnels used for Mobile IP services. When entered without any optional syntax, the show mobile-ip tunnel command displays information about static and dynamic tunnels registered with Mobile IP in the context within which you issue this command. Dynamic and static options display relevant information within a context (unless the all-contexts keyword is specified).

Note:  
By default, most show commands (in any mode) display information for the current context only or, depending on the command syntax, for all contexts. If you are an administrator for the local context, you can insert the optional context ctx-name construct, preceding the show command, to view output for the specified context without entering that context.

Note:  
By appending a space followed by the pipe ( | ) character at the end of a show command, you can filter the output using a set of modifier keywords and arguments. For more information, see Modifying Output of show Commands in the document, Using the CLI.

1.39.6   Examples

The following example shows how to display detailed information about tunnels used for Mobile IP services:

[local]Redback>show mobile-ip tunnel detail 
Tunnel: IPIP 1  ( Interface: subif@local )
    Remote IP      : 1.1.1.2        Local IP       : 1.1.1.1@local
    Admin state    : Up             Oper State     : Up
    Cct state      : Up             Cct handle     :255/24:1023:63/0/1/1
    Tnl State      : Up             Tnl time left  : N/A
    Pndg req cnt   : 0              Binding count  : 1
    Home Slot Mask : 0x01 Tunnel: GRE 4  ( Interface: Unbound )
    Remote IP      : 1.1.1.2         Local IP      : 1.1.1.1@local
    Admin state    : Down            Oper State    : Down
    Cct state      : Up              Cct handle    : 255/4:1023:63/0/1/4
    Tnl State      : Initial         Tnl time left : N/A
    Pndg req cnt   : 0               Binding count : 0
    Home Slot Mask : 0x01

The following example shows how to display detailed information about static tunnels used for Mobile IP services:

[local]Redback>show mobile-ip tunnel static detail 
Tunnel: GRE 4  ( Interface: Unbound )
    Remote IP      : 1.1.1.2         Local IP      : 1.1.1.1@local
    Admin state    : Down            Oper State    : Down
    Cct state      : Up              Cct handle    : 255/4:1023:63/0/1/4
    Tnl State      : Initial         Tnl time left : N/A
    Pndg req cnt   : 0               Binding count : 0
    Home Slot Mask : 0x01

The following example shows how to display detailed information about dynamic tunnels used for Mobile IP services:

[local]Redback>show mobile-ip tunnel dynamic detail 
Tunnel: IPIP 1  ( Interface: subif@local )
    Remote IP      : 1.1.1.2         Local IP      : 1.1.1.1@local
    Admin state    : Up              Oper State    : Up
    Cct state      : Up              Cct handle    :255/24:1023:63/0/1/1
    Tnl State      : Up              Tnl time left : N/A
    Pndg req cnt   : 0               Binding count : 1
    Home Slot Mask : 0x01

The following example shows how to display detailed information about all dynamic tunnels used for Mobile IP services in all contexts:

[local]Redback>show mobile-ip tunnel all-contexts dynamic detail  

Tunnel: IPIP 1  ( Interface: subif@local )

    Remote IP      : 1.1.1.2       Local IP     : 1.1.1.1@local

    Admin state    : Up            Oper State   : Up

    Cct state      : Up            Cct handle   : 255/24:1023:63/0/1/1

    Tnl State      : Up            Tnl time left: N/A

    Pndg req cnt   : 0             Binding count: 1

    Home Slot Mask : 0x01

Tunnel: IPIP 2   Interface: foo1@fa-ctx )

    Remote IP      : 1.1.1.1       Local IP     : 1.1.1.2@fa-ctx

    Admin state    : Up            Oper State   : Up

    Cct state      : Up            Cct handle   : 255/24:1023:63/0/1/2

    Tnl State      : Up            Tnl time left: N/A

    Pndg req cnt   : 0             Visitor count: 1

1.40   show mobile-ip visitor

To display a specific registered visitor, the command syntax is:

show mobile-ip visitor {{mac-address mac-addr} | {nai string} | {circuit circuit-handle}}

To display registered visitors with inactive sessions, the command syntax is:

show mobile-ip visitor inactive

To display registered visitors having a specific IP address in the home domain (HoA) and optionally, a specific home-agent (HA) address, the command syntax is:

show mobile-ip visitor ip-addr [home-agent-peer ha-ip-addr]

To display registered visitors for a care-of-address (CoA) interface, a HA peer address, or a Mobile IP interface, the command syntax is:

show mobile-ip visitor [care-of-address coa-ip-addr] [home-agent-peer ha-ip-addr] [interface if-name] [detail]

1.40.1   Purpose

Displays a list of Mobile IP visitors on a foreign-agent (FA) instance.

1.40.2   Command Mode

1.40.3   Syntax Description

mac-address mac-addr

Displays the information for visitor identified by its Medium Access Control (MAC) address.

nai string

Displays the information for visitor identified by its Network Access Identifier (NAI).

circuit circuit-handle

Displays the information for visitor identified by the local circuit handle.

inactive

Displays the information for visitors with inactive sessions.

ip-addr

Home address (HoA) of the visitor to be displayed.

home-agent-peer ip-addr

HA peer IP address for visitors to be displayed.

care-of-address coa-ip-addr

IP address for a CoA interface for visitors for the care-of-address and interface to be displayed.

interface if-name

Name of access interface of visitors to be displayed.

detail

Displays detailed Mobile IP visitor information.

1.40.4   Default

When entered without any optional syntax, the show mobile-ip visitor command displays all visitors to an FA instance.

1.40.5   Usage Guidelines

Use the show mobile-ip visitor command to display a list of Mobile IP visitors to an FA instance.

Use the optional constructs to filter the list by:

The list does not include those visitors with pending registrations. For information about the visitors and pending registrations, see the show mobile-ip visitor pending command.

The following table describes some of the fields displayed by the show mobile-ip visitor detail command.

Table 7    Fields Displayed by the show mobile-ip visitor detail Command

Field Name

Information Displayed

Home Slot

The Home Slot field displays the slot of the FA subscriber circuit. The slot on which the FA subscriber circuits gets created is referred to as the home slot. This slot is typically the slot associated with the access circuit via which the MN registered for the very first time.

Home Slot Moves

The Home Slot Moves field displays the number of times a subscriber circuit's home slot changed. The Home Slot assigned to the subscriber circuit may be changed if the currently assigned slot fails. The change in home slot is referred to as a home slot move.

Visitor Circuit

This field displays the visitor circuit handle which is the internal identifier assigned to the FA subscriber circuit; that is, the identifier assigned to the visitor circuit.

State

The State field displays whether the subscriber session on the visitor circuit is up or down.

Note:  
By default, most show commands (in any mode) display information for the current context only or, depending on the command syntax, for all contexts. If you are an administrator for the local context, you can insert the optional context ctx-name construct, preceding the show command, to view output for the specified context without entering that context.

Note:  
By appending a space followed by the pipe ( | ) character at the end of a show command, you can filter the output using a set of modifier keywords and arguments. For more information, see Modifying Output of show Commands in the document, Using the CLI.

1.40.6   Examples

The following example shows how to display information for all Mobile IP visitors to an FA instance. The visitor circuit ID in the Visitor-Cct field is 3:

[local]Redback>show mobile-ip visitor
Visitor    NAI      Home Agent    Care-of-Address Visitor-Cct
2.2.2.3    user1    14.1.1.2      14.1.1.1        MIP-FA 3 

The show mobile-ip visitor detail command displays detailed information for all Mobile IP visitors; however, in this example only one visitor, namely NAI abc@rback is found:

[local]Redback>show mobile-ip visitor detail

::::: Mobile IP Visitor  2.2.2.1  :::::
MAC-address    : 01:00:5e:00:00:01  NAI          : abc@rback
Access Intf    : to_mn            Access Circuit : 3/2:1023:63/1/1/5
Home Agent     : 1.1.1.1          Care-of Address: 1.1.1.2
HA Tunnel Cct  : ipip 3           HA Tunnel Intf : ha-tnl-if
Lifetime (secs): 1800             Rem lifetime   : 1442
Up time        : 00:06:57         Registration Id: cd52a8be.3
UDP port       : 4060             Reg Flags      : .B....T.
Home Slot      : 3                Home Slot Moves: 0
Visitor SPG    : 0                Visitor Circuit: 255/29:1023:63/11/2/3
Revocation     : Disabled
Tunnel Circuit : 255/24:1023:63/0/1/3
State          : Up

1.41   show mobile-ip visitor pending

show mobile-ip visitor pending [home-agent-peer ha-ip-addr] [care-of-address coa-ip-addr] [interface if-name] [detail]

1.41.1   Purpose

Displays a list of pending Mobile IP visitors on a foreign-agent (FA) instance.

1.41.2   Command Mode

1.41.3   Syntax Description

home-agent-peer ha-ip-addr

Optional. IP address for a home-agent (HA) peer for pending visitors.

care-of-address coa-ip-addr

Optional. IP address for a care-of-address (CoA) peer for pending visitors to be displayed for the CoA and HA peer.

interface if-name

Name of access interface of pending visitors to be displayed.

detail

Optional. Displays detailed Mobile IP pending visitor information.

1.41.4   Default

When entered without any optional syntax, the show mobile-ip visitor pending command displays all pending visitors on an FA instance.

1.41.5   Usage Guidelines

Use the show mobile-ip visitor pending command to display a list of pending Mobile IP visitors to an FA instance.

Use the optional home-agent-peer ha-ip-addr or care-of-address coa-ip-addr construct to list only the pending registrations for a specific HA peer or CoA peer, respectively.

The list does not include visitors whose registration is not pending.

Note:  
By default, most show commands (in any mode) display information for the current context only or, depending on the command syntax, for all contexts. If you are an administrator for the local context, you can insert the optional context ctx-name construct, preceding the show command, to view output for the specified context without entering that context.

Note:  
By appending a space followed by the pipe ( | ) character at the end of a show command, you can filter the output using a set of modifier keywords and arguments. For more information, see Modifying Output of show Commands in the document, Using the CLI.

1.41.6   Examples

The following example shows how to display all pending Mobile IP visitors to an FA instance:

[local]Redback>show mobile-ip visitor pending
Visitor    NAI      Home Agent      Care-of-Address Access Cct     

2.2.2.4    user1    14.1.1.2        14.1.1.1        3/2 

The following example shows how to display detailed information for all pending Mobile IP visitors to an FA instance:

[local]Redback>show mobile-ip visitor pending detail
::::: Mobile IP Visitor  2.2.2.4  :::::

  MAC-address    : 01:00:5e:00:00:01  NAI            : user1

  Access Circuit : 3/2                Access Intf    : foreign-sub

  Home Agent     : 14.1.1.2           Care-of Address: 14.1.1.1

  HA Tunnel Cct  : gre 2              HA Tunnel Intf : gre-tunnel

  Lifetime (secs): 1800               Ageout (secs)  : 4

  Up time        : 00:00:03           Registration Id: c9c844efd.2

  UDP port       : 4060               Reg Flags      : SB..G.T.

1.42   show mpls

show mpls {detail | interface [detail] | ism [detail] | label-mapping [space-id | bgp [detail] | detail | ldp [detail] | mpls-static [detail] | rsvp [detail]] | log {ism_tx | {msg_rx | msg_tx} [bgp | ldp | mpls-static | rsvp] | ppa_tx | rib_tx} | lsp [address ip-addr [detail] | bypass | detail | ldp [detail] | mpls-static [detail] | rsvp [detail]] | summary}

1.42.1   Purpose

Displays label manager (LM) information.

1.42.2   Command Mode

all modes

1.42.3   Syntax Description

detail

Displays detailed Multiprotocol Label Switching (MPLS) information. When used as an option, displays detailed information for the specified LM subset.

interface

Displays MPLS interface information.

ism

Displays Interface and Circuit State Manager (ISM) statistics.

label-mapping

Displays label mapping information.

space-id

Optional. Label space ID number. When specified, displays label mapping information only for the specified label space. The range of values is 0 to 65,535.

bgp

Optional. When used with the label mapping keyword, displays only Border Gateway Protocol (BGP) label mapping information. When used with the log msg_rx construct, or the log msg_tx keyword, displays only event logging information sent to, or received from, BGP clients. When used with the lsp keyword, displays label-switched path (LSP) information only for BGP entries.

ldp

Optional. When used with the label mapping keyword, displays only Label Distribution Protocol (LDP) label mapping information. When used with the log msg_rx construct, or the log msg_tx keyword, displays only event logging information sent to, or received from, LDP clients. When used with the lsp keyword, displays LSP information only for LDP entries.

mpls-static

Optional. When used with the label mapping keyword, displays only MPLS static LSP mapping information. When used with the log msg_rx construct, or the log msg_tx keyword, displays only event logging information sent to, or received from, MPLS static clients. When used with the lsp keyword, displays LSP information only for MPLS static entries.

rsvp

Optional. When used with the label mapping keyword, displays only Resource Reservation Protocol (RSVP) label mapping information. When used with the log msg_rx construct, or the log msg_tx keyword, displays only event logging information sent to, or received from, RSVP clients. When used with the lsp keyword, displays LSP information only for RSVP entries.

log

Displays event logging information.

ism_tx

Displays event messages sent to the ISM.

msg_rx

Displays event messages received by clients.

msg_tx

Displays event messages sent to clients.

ppa_tx

Displays event messages sent to Packet Processing ASICs (PPAs).

rib_tx

Displays event messages sent to the Routing Information Base (RIB).

lsp

Displays LSP information.

address ip-addr

Optional. Displays information for LSPs with the specified endpoint.

bypass

Optional. Displays bypass LSP information.

summary

Displays summary MPLS information.

1.42.4   Default

None

1.42.5   Usage Guidelines

Use the show mpls command to display LM information.

Note:  
By default, most show commands (in any mode) display information for the current context only or, depending on the command syntax, for all contexts. If you are an administrator for the local context, you can insert the optional context ctx-name construct, preceding the show command, to view output for the specified context without entering that context.

Note:  
By appending a space followed by the pipe ( | ) character at the end of a show command, you can filter the output using a set of modifier keywords and arguments. For more information, see Modifying Output of show Commands in the document, Using the CLI. For information about troubleshooting MPLS, see the MPLS Troubleshooting document.

1.42.6   Examples

The following example displays LM information:

[local]Redback>show mpls



Context id:            : 0x40080001

Traffic-eng flags:     : default-te

Feature path flags:    : 

The following example displays ISM statistics:

[local]Redback>show mpls ism



 ISM Statistics:

  Total events: ipc rcvd: 0, ipc err 0, unknown event 0



   ID: I/F   : state 3, cfg 1, IP cfg 1,

       Cct   : state 0, Cct cfg 0

       Port  : state 0, Port cfg 0

       Lg    : cfg 0

       L2tp  : sesscfg 0

       Hdr   : only 1

       GrpMac: cfg 0



   CCT SUBID: down 0, up 0, create 0, del 0, par_up 0

         CFG: eth 0, ocn 0, 1q 0, tun 0, fr 0, ppp 0

              atm 0, lm 0, l2tp 0, cfg 0

      LG CFG: hdlc 0, eth 0

         SUB: clear 0, down 0, down_cplt 0



   I/F SUBID: down 0, up 1, create 1, del 0, bind 1, unbind 0

         CFG: cfg 1, ipcfg 1



   PORT SUBID: down 0, up 0, del 0

          CFG: eth 0, stsn 0



   LG SUBID: grp cfg 0, ungrp cfg 0, prot grp cfg 0

             prot cct cfg 0, prot grp action 0



   L2TPSESS SUBID: cfg 0



   GRPMAC: UCAST: reg 0, dereg 0

           MCAST: reg 0, dereg 0

The following example displays label mapping information:

[local]Redback>show mpls label-mapping



Codes : S - MPLS-Static, R - RSVP, L - LDP, B - BGP



Type    In Label  Action    Direct Next hop     Out Label 

S       125       pop                           0         

S       25        swap      10.2.1.2            35        

S       135       swap      10.1.1.2            125       

R       262144    php       10.2.1.2            3         

R       262145    php       10.1.1.2            3         

The following example displays event messages sent to the ISM:

[local]Redback>show mpls log ism_tx



There are total of 3 log entries in buffer



    1:  Mar 29 13:26:47

        IPC_ISM2_CLIENT_REG: for intf_grid 10000001



    2:  Mar 29 13:26:47

        ISM2_EVENT_E_CCT_CREATE: cct handle 255/3:1023:63/2/1/2

        cct_hdr_flags 4

        ISM2_EVENT_E_CCT_LMCFG: cct handle 255/3:1023:63/2/1/2,

        cct_hdr_flags 0, lm_flags 0, context_id 40080001,

        ls_egress 10.2.1.2, intf_grid 0, adj_id 300011, slot 2,ver 1

        ISM2_EVENT_E_CCT_UP: cct handle 255/3:1023:63/2/1/2

        cct_hdr_flags 0



    3:  Mar 29 13:26:47

        ISM2_EVENT_E_CCT_CREATE: cct handle 255/14:1023:63/2/1/1

        cct_hdr_flags 4

        ISM2_EVENT_E_CCT_LMCFG: cct handle 255/14:1023:63/2/1/1,

        cct_hdr_flags 0, lm_flags 0, context_id 40080001,

        ls_egress 0.0.0.0, intf_grid 0, adj_id 0, slot 0,ver 1

        ISM2_EVENT_E_CCT_UP: cct handle 255/14:1023:63/2/1/1

        cct_hdr_flags 0

The following example displays event messages received by clients:

[local]Redback>show mpls log msg_rx



There are total of 4 log entries in buffer



    1:  Mar 29 13:26:47  from: MPLS-STATIC

        REGISTER



    2:  Mar 29 13:26:47  from: RSVP

        REGISTER



    3:  Mar 29 13:26:47  from: MPLS-STATIC

        SET NEXTHOP:

        Egress 10.2.1.2, context 0x40080001

        nhop count 1 proto 1 flags 0x0,

        fec_type 1, ribtbl_id 40090001, lsp_prlen 32

        nhop 1:: LSP Alloc:

          upstream label 0

          ls_context 40080001, ls_spcid 0

          LSP tnlid 1, LSP cct 255/3:1023:63/2/1/2

          out cct 3/7:1023:63/1/1/5, encap-type 1000000

          lcontext 0, ltblid 0

          ip addr 10.1.1.1, out intf grid 10000001, flags 2

          nhop_adjid 0, nhop alt adjid 0, bypass label 0 

          out lbl stack cnt 1

          Label stack:

                label 25, action: PUSH



    4:  Mar 29 13:26:47  from: MPLS-STATIC

        SET NEXTHOP:

        Egress 0.0.0.0, context 0x0

        nhop count 1 proto 1 flags 0x0,

        fec_type 0, ribtbl_id 0, lsp_prlen 0

        nhop 1:: Label Alloc:

          upstream label 125

          ls_context 40080001, ls_spcid 0

          LSP tnlid 0, LSP cct Cct invalid

          out cct Cct invalid, encap-type 0

          lcontext 0, ltblid 0

          ip addr 0.0.0.0, out intf grid 0, flags 1

          nhop_adjid 0, nhop alt adjid 0, bypass label 0 

          out lbl stack cnt 1

          Label stack:

                label 0, action: POP

The following example displays event messages sent by PPAs:

[local]Redback>show mpls log ppa_tx



There are total of 3 log entries in buffer



    1:  Mar 29 13:26:47

        LMSG_UPD_CIRCUIT: slot 3, asid IPPA, circuit 3/7:1023:63/1/1/5,

        sense 1, ls_context 40080001, ls_spcid 0, flags 0,

        ver 1, type 3, len 32



    2:  Mar 29 13:26:47

        LMSG_UPD_LBLSW: slot 3, asid IPPA, context 40080001,

        spcid 0, label 125, action pop, adj_id 0,

        nexthop cct Cct invalid,

        alternative adj_id 0, bypass label 0, 

        alternative lsp cct Cct invalid, bypass_action NONE, 

        lookup_ctx 0, lookup_tblid 0, sw_push_lbl 0

        flags 0, ver 1, type 1, len 68



    3:  Mar 29 13:26:47

        LMSG_UPD_ADJ: slot 3, asid EPPA, dcnhop 10.1.1.1, adj_id 0,

        nhcc 3/7:1023:63/1/1/5, lspcct 255/3:1023:63/2/1/2, 

        dcnhop encaps 1000000, context 40080001, inst 0,

        flags 2, lbl stack cnt 1, ver 1, type 2, len 60

The following example displays event messages sent by the RIB:

[local]Redback>show mpls log rib_tx



There are total of 1 log entries in buffer



  1:  Mar 29 13:26:47

      ADD, flags 0x22, prefix 10.2.1.2, len 32

      context 40080001 dist 7 nhop, cnt 1

      nhop 0:: add 0.0.0.0, intf grid 4f010003, cct 255/3:1023:63/2/1/2

The following example displays LSP information:

[local]Redback>show mpls lsp



Codes : S - MPLS-Static, R - RSVP, L - LDP, B - BGP



Type Endpoint         Direct Next-hop  Out Label    LSP Circuit

R    10.2.1.2/32      10.1.1.1         0            255/3:1023:63/2/1/3

R    10.2.1.2/32      10.1.1.1         262144       255/3:1023:63/2/1/1

S    10.2.1.2/32      10.1.1.1         25           255/3:1023:63/2/1/2

The following example displays summary label manager information:

[local]Redback>show mpls summary



LSPs: 1

1.43   show mpls interface

show mpls interface

1.43.1   Purpose

Displays Multiprotocol Label Switching (MPLS) interface information.

1.43.2   Command Mode

all modes

1.43.3   Syntax Description

This command has no keywords or arguments.

1.43.4   Default

None

1.43.5   Usage Guidelines

Use the show mpls interface command to display MPLS interface information.

Note:  
By default, most show commands (in any mode) display information for the current context only or, depending on the command syntax, for all contexts. If you are an administrator for the local context, you can insert the optional context ctx-name construct, preceding the show command, to view output for the specified context without entering that context.

Note:  
By appending a space followed by the pipe ( | ) character at the end of a show command, you can filter the output using a set of modifier keywords and arguments. For more information, see Modifying Output of show Commands in the document, Using the CLI. For information about troubleshooting MPLS, see the MPLS Troubleshooting document.

1.43.6   Examples

The following example displays output from the show mpls interface command:

[local]Redback>show mpls interface
  --- All MPLS Interfaces ---



Inst Address/Mask       Name        Enabled  State  Bound to

1    1.1.1.1/24         one         Yes      Up     7/4

1.44   show mpls-static label-action

show mpls-static label-action [lsp-name] [detail]

1.44.1   Purpose

Displays label action information.

1.44.2   Command Mode

all modes

1.44.3   Syntax Description

lsp-name

Optional. Name of a label-switched path (LSP) for which label action information is displayed.

detail

Optional. Displays detailed label action information for the specified LSP or all LSPs.

1.44.4   Default

Displays information for all label actions.

1.44.5   Usage Guidelines

Use the show mpls-static label-action command to display label action information.

Use the lsp-name argument to display label action information only for a specific LSP.

Use the detail keyword to display the detailed label action information; otherwise, the summary information is displayed.

Note:  
By default, most show commands (in any mode) display information for the current context only or, depending on the command syntax, for all contexts. If you are an administrator for the local context, you can insert the optional context ctx-name construct, preceding the show command, to view output for the specified context without entering that context.

Note:  
By appending a space followed by the pipe ( | ) character at the end of a show command, you can filter the output using a set of modifier keywords and arguments. For more information, see Modifying Output of show Commands in the document, Using the CLI. For information about troubleshooting MPLS, see the MPLS Troubleshooting document.

1.44.6   Examples

The following example displays label action information:

[local]Redback>show mpls-static label-action



In-label  Action      Out-label Nhop            State       

25        swap        35        10.2.1.2        Up          

135       swap        125       10.1.1.2        Up          

35        pop                                   Up          

The following example displays detailed label action information:

[local]Redback>show mpls-static label-action detail



In-label            : 125        Action         : pop

Out-label           : 0          Nhop           : 0.0.0.0

State               : Up        

Outgoing circuit    : N/A

Outgoing intf grid  : 0x0

1.45   show mpls-static lsp

show mpls-static lsp [detail]

1.45.1   Purpose

Displays Multiprotocol Label Switching (MPLS) static label-switched path (LSP) information.

1.45.2   Command Mode

all modes

1.45.3   Syntax Description

detail

Optional. Displays detailed information.

1.45.4   Default

Displays summary information for all static LSPs.

1.45.5   Usage Guidelines

Use the show mpls-static lsp command to display MPLS LSP information.

Use the detail keyword to display the detailed LSP information; otherwise, the summary information is displayed.

Note:  
By default, most show commands (in any mode) display information for the current context only or, depending on the command syntax, for all contexts. If you are an administrator for the local context, you can insert the optional context ctx-name construct, preceding the show command, to view output for the specified context without entering that context.

Note:  
By appending a space followed by the pipe ( | ) character at the end of a show command, you can filter the output using a set of modifier keywords and arguments. For more information, see Modifying Output of show Commands in the document, Using the CLI. For information about troubleshooting MPLS, see the MPLS Troubleshooting document.

1.45.6   Examples

The following example displays summary information for a static LSP:

[local]Redback>show mpls-static lsp



                 Static LSPs



LSP              ID     Next-hop      Out-Label   Endpoint        State

W-E-stat         1      10.1.1.1      25          10.2.1.2        Up

The following example displays detailed information for a static LSP:

[local]Redback>show mpls-static lsp detail



                 Static LSPs



LSP              ID     Next-hop      Out-Label   Endpoint        State



              --- Static label-switched-path W-E-stat ---



Tunnel id           : 1

Endpoint            : 10.2.1.2            Next Hop         : 10.1.1.1

State               : Up                  Out Label        : 25

LSP Circuit         : 255/3:1023:63/2/1/2

Outgoing Circuit    : 3/7:1023:63/1/1/5

Outgoing Intf grid  : 0x10000001

1.46   show msdp peer

show msdp peer peer-addr

1.46.1   Purpose

Displays configured Multicast Source Discovery Protocol (MSDP) peer information.

1.46.2   Command Mode

all modes

1.46.3   Syntax Description

peer-addr

IP address of an MSDP peer.

1.46.4   Default

None

1.46.5   Usage Guidelines

Use the show msdp peer command to display configured MSDP peer information.

Use the peer-addr argument to display information for only a specific peer.

Note:  
By default, most show commands (in any mode) display information for the current context only or, depending on the command syntax, for all contexts. If you are an administrator for the local context, you can insert the optional context ctx-name construct, preceding the show command, to view output for the specified context without entering that context.

Note:  
By appending a space followed by the pipe ( | ) character at the end of a show command, you can filter the output using a set of modifier keywords and arguments. For more information, see Modifying Output of show Commands in the document, Using the CLI.

1.46.6   Examples

The following example displays MSDP peer information for the peer, 10.200.1.1:

[local]Redback>show msdp peer 10.200.1.1
Peer 10.200.1.1                   Our TCP source: 10.200.1.2 (lo1)

  State       : Established 

  Elapsed     : 00:03:20             TTL threshold: 0

  Resets      : 2                    Last reset reason: Remote close

  Holdtime    : 00:01:10             Last heard/sent: 00:00:19/00:00:19

  Reconnect   : 00:00:00             Keepalive: 00:00:40

  Mesh Group  :                     

  Default Peer: No        

  I/O queue size: 0/0

  SA Input Filter ACL : 

  SA Output Filter ACL: 



  Message counters

  Last cleared : 00:17:26  

  Total  Messages received/sent: 8/8

  RPF failures : 0

  Notification messages received/sent : 0/0

  Keepalive messages received/sent : 8/8

  SA messages received/sent : 0/0

  SA Response received/sent : 0/0

  SA Request received/sent : 0/0

  Data packets from/to peer : 0/0

  Data packets from/to PIM : 0/0

1.47   show msdp sa-cache

show msdp sa-cache [group-addr [src-addr]] | [as {asn | nn:nn}] | [count] [peer peer-addr] | [rp rp-addr]

1.47.1   Purpose

Displays Multicast Source Discovery Protocol (MSDP) source active (SA) messages cached on the router.

1.47.2   Command Mode

all modes

1.47.3   Syntax Description

group-addr

Optional. IP address of the Internet Group Management Protocol (IGMP) group.

src-addr

Optional. IP address of the multicast source that is transmitting to the group. A source does not need to be a member of the group.

asasn

Optional. Autonomous system number (ASN), in integer format, from which MSDP SA cache entries have been learned. The range of values is 1 to 65,535. The subrange, 64,512 to 65,535, is reserved for private autonomous systems.

as nn:nn

Optional. ASN, in 4-byte integer format, from which MSDP SA cache entries have been learned. With 4-byte integer format, the first nn indicates the two higher-order bytes, and the second nn denotes the two lower-order bytes.

count

Optional. Number of SA cache entries.

peer peer-addr

Optional. Peer IP address from which MSDP SA cache entries have been learned.

rp rp-addr

Optional. Rendezvous point IP address from which MSDP SA cache entries have been learned.

1.47.4   Default

None

1.47.5   Usage Guidelines

Use the show msdp sa-cache command to display MSDP SA messages cached on the router.

Use the group-addr argument to display all MSDP SA cache entries for a specific IGMP group.

Use the group-addr and src-addrarguments together to display MSDP SA cache entries for the (S, G) pair.

Use the asasn or as nn:nnconstruct to display MSDP SA cache entries learned from the specified autonomous system.

Use the count keyword to display the number of SA messages cached from the RP and peers.

Use the peer peer-addr construct to display MSDP SA cache entries learned from the specified peer address.

Use the rprp-addr construct to display MSDP SA cache entries learned from the specified RP address.

Note:  
By default, most show commands (in any mode) display information for the current context only or, depending on the command syntax, for all contexts. If you are an administrator for the local context, you can insert the optional context ctx-name construct, preceding the show command, to view output for the specified context without entering that context.

Note:  
By appending a space followed by the pipe ( | ) character at the end of a show command, you can filter the output using a set of modifier keywords and arguments. For more information, see Modifying Output of show Commands in the document, Using the CLI.

1.47.6   Examples

The following example displays output from the show msdp sa-cache command:

[local]Redback>show msdp sa-cache
MSDP Source-Active Cache
(11.1.1.21, 224.132.1.1), RP 10.200.1.2, AS ?, Peer 10.200.1.2, 00:02:51/00:04:09
(11.1.1.21, 224.138.1.1), RP 10.200.1.2, AS ?, Peer 10.200.1.2, 00:02:51/00:04:09
(11.1.1.21, 224.135.1.1), RP 10.200.1.2, AS ?, Peer 10.200.1.2, 00:02:51/00:04:09

1.48   show msdp summary

show msdp summary

1.48.1   Purpose

Displays configured Multicast Source Discovery Protocol (MSDP) peer summary information.

1.48.2   Command Mode

all modes

1.48.3   Syntax Description

This command has no keywords or arguments.

1.48.4   Default

None

1.48.5   Usage Guidelines

Use the show msdp summary command to display configured MSDP peer summary information.

Note:  
By default, most show commands (in any mode) display information for the current context only or, depending on the command syntax, for all contexts. If you are an administrator for the local context, you can insert the optional context ctx-name construct, preceding the show command, to view output for the specified context without entering that context.

Note:  
By appending a space followed by the pipe ( | ) character at the end of a show command, you can filter the output using a set of modifier keywords and arguments. For more information, see Modifying Output of show Commands in the document, Using the CLI.

1.48.6   Examples

The following example displays summary information for all configured MSDP peers:

[local]Redback>show msdp summary
* - Default Peer

  Peer Address    Interface     State          Uptime/     Reset     AS

                                               Downtime    count

  10.200.1.3      lo1           Established    00:16:27    0         ?

  10.200.1.4      lo1           Established    00:16:17    0         ?

  10.200.1.1      lo1           Established    00:02:36    2         ?