COMMAND DESCRIPTION     23/190 82-CRA 119 1170/1-V1 Uen C

Commands: show p through show q

Copyright

© Ericsson AB 2009–2010. All rights reserved. No part of this document may be reproduced in any form without the written permission of the copyright owner.

Disclaimer

The contents of this document are subject to revision without notice due to continued progress in methodology, design and manufacturing. Ericsson shall have no liability for any error or damage of any kind resulting from the use of this document.

Trademark List

Contents

1   Command Descriptions

Commands starting with “show p” through commands starting with “show q” are included.

1.1   show pim bsr-router

1.1.1   Purpose

• Displays bootstrap router (BSR) and candidate rendezvous point (C-RP) information.

1.1.2   Command Mode

all modes

1.1.3   Syntax Description

This command has no keywords or arguments.

1.1.4   Default

None

1.1.5   Usage Guidelines

• Use the show pim bsr-router command to display BSR and C-RP information.

Note:  

By default, most show commands (in any mode) display information for the current context only or, depending on the command syntax, for all contexts. If you are an administrator for the local context, you can insert the optional context ctx-name construct, preceding the show command, to view output for the specified context without entering that context. For more information about using the context ctx-name construct, see the context command description.

Note:  

By appending a space followed by the pipe ( | ) character at the end of a show command, you can filter the output using a set of modifier keywords and arguments. For more information, see “Modifying Output of show Commands” in Using the CLI.

1.1.6   Examples

The following example displays information for all BSRs and C-RPs:

[local]Redback>show pim bsr-router

PIM Bootstrap Information

BSR address:    11.1.1.1

Uptime:         3d06h, BSR Priority: 0, Hash mask length: 0

Next Bootstrap: 00:00:37



Next Candidate RP advertisement in 00:00:42

RP: 11.1.1.1(fxp1), Group Acl:

1.2   show pim circuit

1.2.1   Purpose

• Displays circuit-specific information for Protocol Independent Multicast (PIM).

1.2.2   Command Mode

all modes

1.2.3   Syntax Description

This command has no keywords or arguments.

1.2.4   Default

None

1.2.5   Usage Guidelines

• Use the show pim circuit command to display circuit-specific information for PIM.

Note:  

By default, most show commands (in any mode) display information for the current context only or, depending on the command syntax, for all contexts. If you are an administrator for the local context, you can insert the optional context ctx-name construct, preceding the show command, to view output for the specified context without entering that context. For more information about using the context ctx-name construct, see the context command description.

Note:  

By appending a space followed by the pipe ( | ) character at the end of a show command, you can filter the output using a set of modifier keywords and arguments. For more information, see “Modifying Output of show Commands” in Using the CLI.

1.2.6   Examples

The following example displays circuit-specific information for PIM:

[local]Redback>show pim circuit

  Number of circuits: 4

    1/9:1023:63/1/1/5, fxp1, Up, recv permit/send permit/unsol permit

    1/11:1023:63/1/1/13, fxp2, Up, recv permit/send permit/unsol permit

    12/1:1:63/1/2/18, fxp3, Up, recv permit/send permit/unsol permit

    12/1:1:63/1/2/19, fxp3, Up, recv permit/send permit/unsol permit

1.3   show pim interface

1.3.1   Purpose

• Displays Protocol Independent Multicast (PIM)-enabled interface information.

1.3.2   Command Mode

all modes

1.3.3   Syntax Description

1.3.4   Default

None

1.3.5   Usage Guidelines

• Use the show pim interface command to display PIM-enabled interface information.

Note:  

By default, most show commands (in any mode) display information for the current context only or, depending on the command syntax, for all contexts. If you are an administrator for the local context, you can insert the optional context ctx-name construct, preceding the show command, to view output for the specified context without entering that context. For more information about using the context ctx-name construct, see the context command description.

Note:  

By appending a space followed by the pipe ( | ) character at the end of a show command, you can filter the output using a set of modifier keywords and arguments. For more information, see “Modifying Output of show Commands” in Using the CLI.

1.3.6   Examples

The following example displays information for all PIM-enabled interfaces:

[local]Redback>show pim interface

Address         Interface      Mode    Cct      Up   Nbr    Hello     DR      BFD
                                       Count    Dn   Count  Intvl
10.2.1.17       E1             sparse    0      Dn   0      30    10.2.1.17 Enabled
11.1.1.1        E2             sparse    0      Dn   0      30    11.1.1.1  Enabled

1.4   show pim mdt

1.4.1   Purpose

• Displays multicast domain tree (MDT) information.

1.4.2   Command Mode

all modes

1.4.3   Syntax Description

This command has no keywords or arguments.

1.4.4   Default

None

1.4.5   Usage Guidelines

Use the show pim mdt command to display MDT information.

The output from this command is context-specific.

The output in a Virtual Private Network (VPN) context shows the MDT group, the source for the VPN, and the context ID only for that VPN context. The output in local context lists MDT information for all VPNs.

Note:  

By default, most show commands (in any mode) display information for the current context only or, depending on the command syntax, for all contexts. If you are an administrator for the local context, you can insert the optional context ctx-name construct, preceding the show command, to view output for the specified context without entering that context. For more information about using the context ctx-name construct, see the context command description.

Note:  

By appending a space followed by the pipe ( | ) character at the end of a show command, you can filter the output using a set of modifier keywords and arguments. For more information, see “Modifying Output of show Commands” in Using the CLI.

1.4.6   Examples

The following example displays MDT information for a VPN-enabled context, VPN1:

[VPN1]Redback>show pim mdt

Multicast Domain Tree information

MDT Group       Interface           Source              Context

239.1.1.1       ic-local            lo1                 0x40080002

The following example displays MDT information for all VPNs:

[local]Redback>show pim mdt



Multicast Domain Tree information

MDT Group       Interface           Source              Context

239.1.1.1       ic-vpn1             lo1                 0x40080002

196.1.1.1       ic-vpn2             lo2                 0x40080003

10.10.1.1       ic-vpn3             lo3                 0x40080004

1.5   show pim neighbor

1.5.1   Purpose

• Displays Protocol Independent Multicast (PIM) neighbor information.

1.5.2   Command Mode

all modes

1.5.3   Syntax Description

This command has no keywords or arguments.

1.5.4   Default

None

1.5.5   Usage Guidelines

• Use the show pim neighbor command to display PIM neighbor information.

Note:  

By default, most show commands (in any mode) display information for the current context only or, depending on the command syntax, for all contexts. If you are an administrator for the local context, you can insert the optional context ctx-name construct, preceding the show command, to view output for the specified context without entering that context. For more information about using the context ctx-name construct, see the context command description.

Note:  

By appending a space followed by the pipe ( | ) character at the end of a show command, you can filter the output using a set of modifier keywords and arguments. For more information, see “Modifying Output of show Commands” in Using the CLI.

1.5.6   Examples

The following example displays information about all PIM neighbors:

[local]Redback>show pim neighbor

PIM Neighbor Table

Neighbor Address Interface   Uptime   Expire   DR hex    Prio hex   GenID    DR    SR intvl   Bfd Status

10.4.1.2         fxp1        00:04:10 00:01:34 0x1      0x17ac7e7a            Y          60        Up

10.5.1.4         fxp2        00:25:22 00:01:22 0x1      0x18ab6e6a            Y          60        Up

1.6   show pim ppa

1.6.1   Purpose

• Displays the Packet Processing ASIC (PPA) state from the Protocol Independent Multicast (PIM) perspective.

1.6.2   Command Mode

all modes

1.6.3   Syntax Description

This command has no keywords or arguments.

1.6.4   Default

None

1.6.5   Usage Guidelines

• Use the show pim ppa command to display the PPA state from the PIM perspective.

Note:  

By default, most show commands (in any mode) display information for the current context only or, depending on the command syntax, for all contexts. If you are an administrator for the local context, you can insert the optional context ctx-name construct, preceding the show command, to view output for the specified context without entering that context. For more information about using the context ctx-name construct, see the context command description.

Note:  

By appending a space followed by the pipe ( | ) character at the end of a show command, you can filter the output using a set of modifier keywords and arguments. For more information, see “Modifying Output of show Commands” in Using the CLI.

1.6.6   Examples

The following example displays output from the show pim ppa command:

[local]Redback>show pim ppa

Slot 2  IPCs sent  :1               Circuit enable/disable:8/0

ePPA    IPCs rcvd  :1               IPC failures:0        

        IPC blocked:NO              Num of IPCs blocked:1

        Status     :UP              Restarts: 1

        Up/Dn time :17:05:19        Multicast Interfaces:4    

        Version    :54              Goal Version:54



Slot 2  IPCs sent  :1               Circuit enable/disable:8/0

iPPA    IPCs rcvd  :1               IPC failures:0        

        IPC blocked:NO              Num of IPCs blocked:1

        Status     :UP              Restarts: 1

        Up/Dn time :17:05:19        Multicast Interfaces:4    

        Version    :54              Goal Version:54



Slot 11 IPCs sent  :1               Circuit enable/disable:14/0

ePPA    IPCs rcvd  :1               IPC failures:0        

        IPC blocked:NO              Num of IPCs blocked:1

        Status     :UP              Restarts: 1

        Up/Dn time :17:05:19        Multicast Interfaces:7    

        Version    :54              Goal Version:54

1.7   show pim rpf

1.7.1   Purpose

Displays reverse path forwarding (RPF) statistics for a specified multicast source.

1.7.2   Command Mode

all modes

1.7.3   Syntax Description

1.7.4   Default

None

1.7.5   Usage Guidelines

Use the show pim rpf command to display RPF statistics for a specified multicast source.

Note:  

By default, most show commands (in any mode) display information for the current context only or, depending on the command syntax, for all contexts. If you are an administrator for the local context, you can insert the optional context ctx-name construct, preceding the show command, to view output for the specified context without entering that context. For more information about using the context ctx-name construct, see the context command description.

Note:  

By appending a space followed by the pipe ( | ) character at the end of a show command, you can filter the output using a set of modifier keywords and arguments. For more information, see “Modifying Output of show Commands” in Using the CLI.

1.7.6   Examples

The following example displays output from the show pim rpf command:

[local]Redback>show pim rpf 11.1.1.1

RPF information for 11.1.1.1

  RPF interface:    fxp1

  RPF neighbor:     102.1.1.1

  RPF route/mask:   11.1.1.0/255.255.255.0

  RPF type:         mbgp

1.8   show pim rp-hash

1.8.1   Purpose

• Displays information about the rendezvous point (RP) to which the specified Internet Group Management Protocol (IGMP) group hashes.

1.8.2   Command Mode

all modes

1.8.3   Syntax Description

1.8.4   Default

None

1.8.5   Usage Guidelines

Use the show pim rp-hash command to display information about the RP to which the specified group hashes (maps).

Note:  

By default, most show commands (in any mode) display information for the current context only or, depending on the command syntax, for all contexts. If you are an administrator for the local context, you can insert the optional context ctx-name construct, preceding the show command, to view output for the specified context without entering that context. For more information about using the context ctx-name construct, see the context command description.

Note:  

By appending a space followed by the pipe ( | ) character at the end of a show command, you can filter the output using a set of modifier keywords and arguments. For more information, see “Modifying Output of show Commands” in Using the CLI.

1.8.6   Examples

The following example displays information about the RP to which the group, 224.121.121.1, hashes:

[local]Redback>show pim rp-hash 224.121.121.1

  RP 10.6.1.2

    Info source: 10.4.1.2, via Bootstrap

         Uptime: 00:05:00, expires: 00:02:58

1.9   show pim rp mapping

1.9.1   Purpose

• Displays a group-to-rendezvous point (RP) mapping cache.

1.9.2   Command Mode

all modes

1.9.3   Syntax Description

1.9.4   Default

None

1.9.5   Usage Guidelines

• se the show pim rp mapping command to display a group-to-RP mapping cache.

Note:  

By default, most show commands (in any mode) display information for the current context only or, depending on the command syntax, for all contexts. If you are an administrator for the local context, you can insert the optional context ctx-name construct, preceding the show command, to view output for the specified context without entering that context. For more information about using the context ctx-name construct, see the context command description.

Note:  

By appending a space followed by the pipe ( | ) character at the end of a show command, you can filter the output using a set of modifier keywords and arguments. For more information, see “Modifying Output of show Commands” in Using the CLI.

1.9.6   Examples

The following example displays the group-to-RP mapping cache:

[local]Redback>show pim rp mapping

PIM Group-to-RP Mappings

Group(s) 224.24.0.0/16

  RP 10.6.1.2

    Info source: 10.4.1.2, via Bootstrap

         Uptime: 00:04:41, expires: 00:02:17

Group(s) 224.121.0.0/16

  RP 10.6.1.2

    Info source: 10.4.1.2, via Bootstrap

         Uptime: 00:04:41, expires: 00:02:17

1.10   show pim ssm

1.10.1   Purpose

Displays the Source-Specific Multicast (SSM) setting in Protocol Independent Multicast (PIM).

1.10.2   Command Mode

all modes

1.10.3   Syntax Description

This command has no keywords or arguments.

1.10.4   Default

None

1.10.5   Usage Guidelines

Use the show pim ssm command to display the SSM setting in PIM.

Note:  

By default, most show commands (in any mode) display information for the current context only or, depending on the command syntax, for all contexts. If you are an administrator for the local context, you can insert the optional context ctx-name construct, preceding the show command, to view output for the specified context without entering that context. For more information about using the context ctx-name construct, see the context command description.

Note:  

By appending a space followed by the pipe ( | ) character at the end of a show command, you can filter the output using a set of modifier keywords and arguments. For more information, see “Modifying Output of show Commands” in Using the CLI.

1.10.6   Examples

The following example displays output from the show pim ssm command:

[local]Redback>show pim ssm

Source Specific Multicast (SSM) setting

SSM address range: default (232.0.0.0/8)

1.11   show pim traffic

1.11.1   Purpose

Displays Protocol Independent Multicast (PIM) traffic statistics.

1.11.2   Command Mode

all modes

1.11.3   Syntax Description

This command has no keywords or arguments.

1.11.4   Default

None

1.11.5   Usage Guidelines

Use the show pim traffic command to display PIM traffic statistics.

Note:  

By default, most show commands (in any mode) display information for the current context only or, depending on the command syntax, for all contexts. If you are an administrator for the local context, you can insert the optional context ctx-name construct, preceding the show command, to view output for the specified context without entering that context. For more information about using the context ctx-name construct, see the context command description.

Note:  

By appending a space followed by the pipe ( | ) character at the end of a show command, you can filter the output using a set of modifier keywords and arguments. For more information, see “Modifying Output of show Commands” in Using the CLI.

1.11.6   Examples

The following example displays PIM traffic statistics:

[local]Redback>show pim traffic

PIM statistics:

 Sent:

      Total 0, Hello 217, Register 0, Register-Stop 0, Join/Prune 5,

      BSR 21, Assert 0, Graft 0, Graft-ack 0, Candidate-RP-advertisement 0

      PIMv1:  Register 0, Register-Stop 0

 Received:

      Total 0, Hello 66, Register 0, Register-Stop 0, Join/Prune 0,

      BSR 12, Assert 0, Graft 0, Graft-ack 0, Candidate-RP-advertisement 0

      PIMv1:  Register 0, Register-Stop 0, Punts 21

 Error:

      Hello 0, Register 0, Register-Stop 0, Join/Prune 0,

      BSR 0, Assert 0, Graft 0, Graft-ack 0, Candidate-RP-advertisement 0

      PIMv1:  Register 0, Register-Stop 0

      I/O errors 0, Short packets 0, Checksum 0

      Unknown type: 0

 Queue:

      Input queue size 0, Input queue overflows 0

1.12   show policy access-list

1.12.1   Purpose

Displays the status of configured policy access control lists (ACLs).

1.12.2   Command Mode

all modes

1.12.3   Syntax Description

1.12.4   Default

When entered without any optional syntax, the show policy access-list command displays information for all policy ACLs in the context, including the statements in each list.

1.12.5   Usage Guidelines

Use the show policy access-list command to display the status of configured policy ACLs.

Use the first-match acl-name construct to display the first statement in the policy ACL that is matched by the criteria that follows the first-match acl-name construct.

Table 1 lists the valid keyword substitutions for the port argument when the argument is used to specify a TCP port.

Table 2 lists the valid keyword substitutions for the port argument when the argument is used to specify a UDP port.

Table 3 lists the valid keyword substitutions for the dscp-value argument.

Note:  

By default, most show commands (in any mode) display information for the current context only or, depending on the command syntax, for all contexts. If you are an administrator for the local context, you can insert the optional context ctx-name construct, preceding the show command, to view output for the specified context without entering that context. For more information about using the context ctx-name construct, see the context command description.

Note:  

By appending a space followed by the pipe ( | ) character at the end of a show command, you can filter the output using a set of modifier keywords and arguments. For more information, see “Modifying Output of show Commands” in Using the CLI.

1.12.6   Examples

The following example displays information about the policy ACL, diff-serve:

[local]Redback>show policy access-list diff-serve



policy access-list diff-serve:

  count 4, sequences: 10 - 40 client count: 0

  modified: 00:03:08 (hh:mm:ss) ago

   seq 10 permit tcp any eq telnet class Expedited_Flow

   seq 20 permit ip any dscp eq ef class Expedited_Flow

   seq 30 permit tcp any eq ftp class Bulk_Data

   seq 40 permit udp any eq tftp class Bulk_Data

The following example displays information about the policy ACL, redirect_acl:

[local]Redback>show policy access-list redirect_acl



policy access-list redirect_acl:

  count: 3, sequences: 10 - 30, client count: 1

  modified: 00:21:34 (hh:mm:ss) ago, version: 8

   condition 101 time-range

    periodic weekdays 00:00 to 23:59 class redir2

   seq 10 permit tcp any any eq www class redir0 condition 101

   seq 20 permit tcp any any eq 81 class redir1

   seq 30 permit tcp any any eq 82 class redir2

The following example displays information about the policy ACL, qos1:

[local]Redback>show policy access-list qos1



policy access-list qos1:

  count: 1, sequences: 10 - 10, client count: 1

  modified: 00:08:35 (hh:mm:ss) ago, version: 4

   condition 100 time-range

    periodic weekdays 00:00 to 23:59 class redir2

   seq 10 permit ip host 10.3.29.3 any class CLASS1 condition 100

1.13   show port

1.13.1   Purpose

Displays a list of ports that are present or configured in the system.

1.13.2   Command Mode

all modes

1.13.3   Syntax Description

1.13.4   Default

Displays only ports that are present on the system.

1.13.5   Usage Guidelines

Use the show port command to display a list of ports that are present or configured in the system.

Table 4 describes the values for the State field that can be displayed for a given port on a SmartEdge 400 or SmartEdge 800 router.

Table 5 describes the values for the State field that can be displayed for a given port on a SmartEdge 100 router.

For more information about low-density line cards, see Configuring Cards.

Note:  

By default, most show commands (in any mode) display information for the current context only or, depending on the command syntax, for all contexts. If you are an administrator for the local context, you can insert the optional context ctx-name construct, preceding the show command, to view output for the specified context without entering that context. For more information about using the context ctx-name construct, see the context command description.

Note:  

By appending a space followed by the pipe ( | ) character at the end of a show command, you can filter the output using a set of modifier keywords and arguments. For more information, see “Modifying Output of show Commands” in Using the CLI.

1.13.6   Examples

The following example displays the list of all ports that are present in a SmartEdge 800 router. In this example, the 4-port Gigabit Ethernet line card is a low-density, 2-port version; ports 2 and 4 are unavailable:

[local]Redback>show port all

Slot/Port:Ch.SubCh  Type                 State

 2/1                oc12                 Unconfigured

 2/2                oc12                 Unconfigured

 2/3                oc12                 Unconfigured

 2/4                oc12                 Unconfigured

 4/1                ethernet             Up

 4/2                ethernet             Up

 4/3                ethernet             Up

 4/4                ethernet             Up

 7/1                ethernet             Up

 9/1                ethernet             Up

 9/2                ethernet             Down - not entitled

 9/3                ethernet             Up

 9/4                ethernet             Down - not entitled

1.14   show port counters

For all other line cards and all media interface cards (MICs), the syntax is:

show port counters [persistent] [slot/port] [detail | live | queue]

1.14.1   Purpose

Displays the counters associated with system ports and channels.

1.14.2   Command Mode

all modes

1.14.3   Syntax Description

1.14.4   Default

Displays last known values of summary counters for all ports.

1.14.5   Usage Guidelines

Use the show port counters command to display counters associated with system ports with values that have been accumulated since the counters were last cleared with the clear port counters command (in exec mode) or the line card was last reloaded.

Use the persistent keyword to display the counters with values accumulated since the system was last reloaded.

Table 6 lists the range of values for the chan-num and sub-chan-num arguments for various types of channelized ports.

If you specify the optional slot, or port, or chan-num arguments, the display shows counter information for the specified line card, or port, or channel; if you specify the optional sub-chan-num argument, the output displays counter information for just that subchannel.

By default, this command displays only summary counter information for all ports with their last known values, which have been cached; cached values are updated every 60 seconds. Use the live keyword to force the system to read and display the current values for the summary counters.

Table 7 describes the summary counter information that is displayed for all port types if the detail keyword is not specified.

Table 8 describes the PPA and packet drop counters, which are displayed for all types of ports when you specify the detail keyword; the data displayed for these counters, with the exception of the rate counters, is live, not cached data.

Table 9 describes the policing counters that are displayed for all types of ports, except for Ethernet ports, when you specify the detail keyword.

Note:  

For counters for ATM ports:

• Per-queue information kept by PPA counters reflects the count since the last policy change.
• If a queuing algorithm is managed by the segmentation and reassembly controller (SARC) on an ATM line card, the counts reported by the PPA counters are zeros.

Table 10 describes the optical data that is displayed for POS and channelized optical ports when you specify the detail keyword.

Table 11 lists the general, transmit, and receive counters that are displayed for Ethernet ports when the detail keyword is specified. These counters are displayed in addition to the PPA and packet drop counters.

(1)  This field is only available for oversubscribable line cards that support propagation of QoS at the port level.

Table 12 describes the Point-to-Point Protocol (PPP) over Ethernet (PPPoE) counters that are displayed for Ethernet ports.

Table 13 describes the counters that are displayed for each queue for the ports specified by the input parameters when you specify the queue keyword. If no queue policy is attached to a port, no per-queue information is displayed.

Note:  

By default, most show commands (in any mode) display information for the current context only or, depending on the command syntax, for all contexts. If you are an administrator for the local context, you can insert the optional context ctx-name construct, preceding the show command, to view output for the specified context without entering that context. For more information about using the context ctx-name construct, see the context command description.

Note:  

By appending a space followed by the pipe ( | ) character at the end of a show command, you can filter the output using a set of modifier keywords and arguments. For more information, see “Modifying Output of show Commands” in Using the CLI. For information about troubleshooting PPPoE, see the BRAS Troubleshooting Guide.

1.14.6   Examples

The following example displays summary counter information for POS port 1 in slot 1; the detailed counters are shown after this example:

[local]Redback>show port counters 1/1

Port            Type                

1/1             pos                  

packets sent       : 49621              bytes sent         : 1091662   

packets recvd      : 49620              bytes recvd        : 1091640   

send packet rate   : 0                  send bit rate      : 16        

recv packet rate   : 0                  recv bit rate      : 16        

rate refresh interval : 60 seconds

The following example displays detailed counters for port 1 on the POS line card in slot 1:

[local]Redback>show port counters 1/1 detail



Counters for port pos 1/1 - Interval: 5d 17:58:07



PPA Port Counters

packets sent       : 49628              bytes sent         : 1091816   

packets recvd      : 49627              bytes recvd        : 1091794   

send packet rate   : 0                  send bit rate      : 16        

recv packet rate   : 0                  recv bit rate      : 16        

IP mcast pkts rcv  : 0                  IP mcast bytes rcv : 0         

IP mcast pkts sent : 0                  IP mcast bytes snt : 0         

rate refresh interval : 60 seconds

PPA Input Counters

idc other errors   : 0                  crc port errors    : 0         

idc overrun errors : 0                  idc abort errors   : 0         

no cct packets     : 0                  no cct bytes       : 0          

cct down pkts      : 0                  cct down bytes     : 0         

unknown encap pkts : 0                  unknown encap byte : 0         

unreach pkts       : 0                  unreach bytes      : 0         

media filter pkts  : 0                  media filter bytes : 0         



PPA Output Counters

WRED drop pkts     : 0                  tail drop pkts     : 0         

adj drop pkts      : 0                  adj drop bytes     : 0         



Packet Drop Counters

not IPv4 drop pkts : 0                  bad IP checksum    : 0         

unhandled IP optns : 0                  link layer bcast   : 0         

bad IP length      : 0                   



Policing Counters

conform pkts       : 0                  conform bytes      : 0         

conform drop pkts  : 0                  conform drop bytes : 0         

exceed pkts        : 0                  exceed bytes       : 0         

exceed drop pkts   : 0                  exceed drop bytes  : 0         



Packet-Over-Sonet physical layer statistics

Active Alarms              : NONE



Sonet Section

     LOS : 0                  LOF : 0                  BIP-B1 : 0



Sonet Line

     AIS : 0                  RDI : 0                  BIP-B2 : 158

    FEBE : 111



Sonet Path

     AIS : 0                  RDI : 0                  BIP-B3 : 0

    FEBE : 0                  LOP : 0                 

Received Sonet Overhead

      F1 : 0x0                 K1 : 0x0                    K2 : 0x0

      S1 : 0x0                 C2 : 0x16                



Transmitted Sonet Overhead

      F1 : 0x0                 K1 : 0x0                    K2 : 0x0

      S1 : 0x0                 C2 : 0x16 

The following example displays detailed counters for port 1 on the Ethernet line card in slot 5:

[local]Redback>show port counters 5/1 detail

Counters for port ethernet 5/1 - Interval: 5d 15:05:38



PPA Port Counters

packets sent       : 3                  bytes sent         : 126       

packets recvd      : 0                  bytes recvd        : 0         

send packet rate   : 0                  send bit rate      : 0         

recv packet rate   : 0                  recv bit rate      : 0         

IP mcast pkts rcv  : 0                  IP mcast bytes rcv : 0         

IP mcast pkts sent : 0                  IP mcast bytes snt : 0         

rate refresh interval : 60 seconds



PPA Input Error Counters

idc other errors   : 0                  crc port errors    : 0         

idc overrun errors : 0                  idc abort errors   : 0         

no cct packets     : 0                  no cct bytes       : 0         

cct down pkts      : 0                  cct down bytes     : 0         

unknown encap pkts : 0                  unknown encap byte : 0         

unreach pkts       : 0                  unreach bytes      : 0         

media filter pkts  : 0                  media filter bytes : 0         



PPA Output Error Counters

WRED drop pkts     : 0                  tail drop pkts     : 0         

adj drop pkts      : 0                  adj drop bytes     : 0         



Packet Drop Counters

not IPv4 drop pkts : 0                  bad IP checksum    : 0         

unhandled IP optns : 0                  link layer bcast   : 0         

bad IP length      : 0                   



General Counters

packets sent       : 3                  packets recvd      : 0         

bytes sent         : 192                bytes recvd        : 0         

mcast pkts sent    : 0                  mcast pkts recvd   : 0         

bcast pkts sent    : 3                  bcast pkts recvd   : 0         

dropped pkts out   : 0                  dropped pkts in    : 0         

pending pkts out   : 0                  pending pkts in    : 0         

port drops out     : 0                  port drops in      : 0         



Transmit Counters

jabber             : 0                  error pkts sent    : 0         

false carrier      : 0                  error bytes sent   : 0         

late collision     : 0                  eth 64 octets      : 3         

underflow          : 0                  eth 65-127 octs    : 0         

regular collision  : 0                  eth 128-255 octs   : 0         

single collision   : 0                  eth 256-511 octs   : 0         

multiple colls     : 0                  eth 512-1023 octs  : 0         

excessive colls    : 0                  eth 1024-1518 octs : 0         

deferred           : 0                  eth > 1518 octs    : 0         

flow control       : 0                   



Receive Counters

runt frames        : 0                  overflows          : 0         

undersized frames  : 0                  eth 64 octets      : 0         

oversized frames   : 0                  eth 65-127 octs    : 0         

crc errors         : 0                  eth 128-255 octs   : 0         

alignment errors   : 0                  eth 256-511 octs   : 0         

symbol errors      : 0                  eth 512-1023 octs  : 0         

error pkts rcvd    : 0                  eth 1024-1518 octs : 0         

error bytes rcvd   : 0                  eth > 1518 octs    : 0         

flow control       : 0 

The following example displays detailed counters for port 1 on the ATM line card in slot 5:

[local]Redback>show port counters 5/1 detail

Counters for port atm 3/1 - Interval: 5d 15:03:28

PPA Port Counters
packets sent       : 0                  bytes sent         : 0         
packets recvd      : 0                  bytes recvd        : 0         
send packet rate   : 0                  send bit rate      : 0         
recv packet rate   : 0                  recv bit rate      : 0         
IP mcast pkts rcv  : 0                  IP mcast bytes rcv : 0         
IP mcast pkts sent : 0                  IP mcast bytes snt : 0         
rate refresh interval : 60 seconds

PPA Input Counters
idc other errors   : 0                  crc port errors    : 0         
idc overrun errors : 0                  idc abort errors   : 0         
no cct packets     : 0                  no cct bytes       : 0         
cct down pkts      : 0                  cct down bytes     : 0         
unknown encap pkts : 0                  unknown encap byte : 0         
unreach pkts       : 0                  unreach bytes      : 0         
media filter pkts  : 0                  media filter bytes : 0         

PPA Output Counters
WRED drop pkts     : 0                  tail drop pkts     : 0         
adj drop pkts      : 0                  adj drop bytes     : 0         

Packet Drop Counters
not IPv4 drop pkts : 0                  bad IP checksum    : 0         
unhandled IP optns : 0                  link layer bcast   : 0         
bad IP length      : 0                   

Policing Counters
conform pkts       : 0                  conform bytes      : 0         
conform drop pkts  : 0                  conform drop bytes : 0         
exceed pkts        : 0                  exceed bytes       : 0         
exceed drop pkts   : 0                  exceed drop bytes  : 0 

1.15   show port detail

1.15.1   Purpose

Displays the medium access control (MAC) address and other lower-layer settings of a single port, all ports on a card, or all ports in the system.

1.15.2   Command Mode

all modes

1.15.3   Syntax Description

1.15.4   Default

Displays information for configured ports in the system.

1.15.5   Usage Guidelines

Use the show port detail command to display the medium access control (MAC) address and other lower-layer settings of a single port, all ports on a card, or all ports in the system.

Note:  

If a port is not configured, the show port detail command does not work and the system reports the error log: Port <s>/<p> is not configured.

If you do not include any arguments, the output includes all ports present or configured in the system.

Table 15 lists the output fields for the show port command (in any mode) with the detail keyword. Not all fields apply to all types of ports; the “Type” and “Slot/Port” field names are not displayed in the output.

(1)  Small form-factor pluggable (SFP) transceivers are supported only on the Gigabit Ethernet, the ATM OC, and the POS OC line cards.

(2)  Gigabit interface converter (GBIC) transceivers are supported only on first and second versions of the Gigabit Ethernet line cards.

(3)  10-Gbps SFP (OC192 XFP) transceivers are supported only on the 10 Gigabit Ethernet (10GE) line card.

(4)  This field is only applicable for the 10G LAN-PHY port type.

(5)  Only supported in hsvc-fair mode on the 8-port ATM OC-3c/STM-1c (atm-oc3e-8-port) and 2-port ATM OC-12c/STM-4c (atm-oc12e-2-port) cards. When executed in vc-fair mode, an error message occurs if executed with any value other than 150 Mbps.

(6)  When Payload line-Rate (150 Mbps) is selected, the actual line-rate received is 149.76 Mbps.

(7)  This field is only applicable for the line cards that support WAN-PHY mode.

(8)  Measured or reported values meet or exceed the transceiver specifications that are documented in Transceivers for SmartEdge line cards.

Note:  

By default, most show commands (in any mode) display information for the current context only or, depending on the command syntax, for all contexts. If you are an administrator for the local context, you can insert the optional context ctx-name construct, preceding the show command, to view output for the specified context without entering that context. For more information about using the context ctx-name construct, see the context command description.

Note:  

By appending a space followed by the pipe ( | ) character at the end of a show command, you can filter the output using a set of modifier keywords and arguments. For more information, see “Modifying Output of show Commands” in Using the CLI.

1.15.6   Examples

[local]Redback>show port 1/1 detail
pos 1/1 state is Down
Description                : 
Line state                 : Down
Admin state                : Down
Media type                 : Sonet OC12 (SM)
Encapsulation              : cisco-hdlc
MTU size                   : 4470 Bytes
Loopback                   : none
Framing                    : sonet
Speed                      : 622080 kbps
Scramble                   : ON
Crc                        : 32
Tx C2 byte                 : 0x16
Rx C2 byte                 : 0x16
Line SF BER                : 10E-4
Line SD BER                : 10E-7
Keepalive                  : Set (10 sec)
Active Alarms              : N/A
Path Alarms                : N/A
SFP / Media Type           : CWDM / MM
Tx path-trace              : 
    73757065 72636f6d 6d370000 00000000  supercomm7......
    00000000 00000000 00000000 00000000  ................
    00000000 00000000 00000000 00000000  ................
    00000000 00000000 00000000 00000d0a  ................
Rx path-trace        : 
    00000000 00000000 00000000 00000000  ................
    00000000 00000000 00000000 00000000  ................
    00000000 00000000 00000000 00000000  ................
    00000000 00000000 00000000 00000000  ................

[local]Redback(config-atm-oc)#show port 10/1 detail

atm 10/1 state is Down
Description :
Line state                 : Down
Admin state                : Down
Link Dampening             : enabled
Link up delay              : 11000
Link down delay            : 2200
Restart link up delay      : 400
Undampened line state      : Down
Dampening Count            : 0
Media type                 : Sonet OC12 (SM)
Encapsulation              : atm
NAS Port Type              :
Loopback                   : none
Framing                    : sonet
Speed                      : 622.08 Mbps
Bandwidth                  : 599.04 Mbps
Tx C2 byte                 : 0x13
Rx C2 byte                 : 0x13
Line SF BER                : 10E-4
Line SD BER                : 10E-7
ATM MTU size               : 65527 Bytes
MTU size                   : 4470 Bytes
ATM Payload Scramble       : ON
Over Subscription Rate     : Unlimited
MAC address                : 00:30:88:01:08:18
Clock Source               : card-reference
CCOD Mode                  : default
Report Only Alarms
  Path Alarms (report only): Payload label mismatch (PLM)
                             Path un-equipped (UNEQ-P)
Active Alarms              : N/A
Path Alarms                : N/A
Path Trace Length          : 64 (62 + 2 framing)
Tx Path Trace              :
    52656462 61636b00 00000000 00000000  Redback.........
    00000000 00000000 00000000 00000000  ................
    00000000 00000000 00000000 00000000  ................
    00000000 00000000 00000000 00000d0a  ................
Rx Path Trace              :
    00000000 00000000 00000000 00000000  ................
    00000000 00000000 00000000 00000000  ................
    00000000 00000000 00000000 00000000  ................
    00000000 00000000 00000000 00000000  ................

[local]Redback>show port 3/1 detail

atm 3/1 state is Up
Description                : ATM port for Multiprotocol circuits
Line state                 : Up
Admin state                : Up
Media type                 : ds3
Encapsulation              : atm
ATM MTU size               : 65527 Bytes
MTU size                   : 5000 Bytes
Loopback                   : none
Framing                    : c-bit
Framing Mode               : ADM
Speed                      : 44.736 Mbps
Bandwidth                  : 44.21 Mbps
Clock Source               : global-reference
Equipment Loopback         : network
Cable Length               : 349 feet (short)
ATM Payload Scramble       : ON
Over Subscription Rate     : Unlimited
MAC address                : 00:00:00:00:00:00
Active Alarms              : NONE
FEAC code received         : NONE

[local]Redback>show port 9/2 detail
ethernet 9/2 state is Down
Description               :
Line state                :Down not entitled
Admin state               :Up
Encapsulation             :ethernet
MTU size                  :1500 Bytes
Speed                     :1000 Mbits/sec
Duplex mode               :full
MAC address               :00:30:88:00:13:1b
Media type                :1000Base-TX
Flow control              :on
Loopback                  :off

[local]Redback>show port 6/1 detail

atm 6/1 state is Up
Description                : ATM port for Multiprotocol circuits
Line state                 : Up
Admin state                : Up
Media type                 : Sonet OC3 (SM)
Encapsulation              : atm
Loopback                   : none
Framing                    : sonet
Speed                      : 155.52 Mbps
Bandwidth                  : 149.76 Mbps
Qos Rate Maximum           : 50 Mbps
Tx C2 byte                 : 0x13
Rx C2 byte                 : 0x1
Line SF BER                : 10E-5
Line SD BER                : 10E-8
ATM MTU size               : 65519 Bytes
MTU size                   : 5000 Bytes
ATM Payload Scramble       : ON
Over Subscription Rate     : Unlimited
MAC address                : 00:00:00:00:00:00
Active Alarms              : NONE

ethernet 5/1 state is Down 
Description : 
Line state : Down 
Admin state : Down 
Link Dampening             : enabled
Link up delay              : 11000
Link down delay            : 2200
Restart link up delay      : 400
Undampened line state : Down 
Dampening Count : 0 
Encapsulation : ethernet 
MTU size : 1500 Bytes 
NAS Port Type : 
PPPoE pado delay : Set(2 sec)
Speed : 1 Gbps 
Duplex mode : full 
MAC address : 00:30:88:01:64:b5 
Media type : 1000Base-LX 
Flow control :rx state:    real time state 
Auto-negotiation : off state: n/a
Link Distance : N/A 
Loopback : off 
Wavelength : 1310.00 nm 
Diag Monitor : Yes 
TX Fault : LOW-PWR-ALARM 
RX Fault : LOS-Fault 
TX Pwr measured[dbm] : -40.00 
RX Pwr measured[dbm] : -40.00 

[local]Redback>show port 3/1 detail
atm 3/1 state is Up
Description                : ATM port for Multiprotocol circuits
Line state                 : Up
Admin state                : Up
Media type                 : Sonet OC3 (SM)
Encapsulation              : atm
Auto-negotiation : on state: unknown
Flc negotiated set : tx-rx-or-rx-only state: real time state
force : disabled state: inactive
Flow-control : tx&rx state: n/a

[local]Redback>show port 1/1 detail

atm 14/1 state is Up  
Description                :
Line state                 : Up  
Admin state                : Up
Link Dampening             : enabled
Link up delay              : 11000
Link down delay            : 2200
Restart link up delay      : 400
Undampened line state      : Up
Dampening Count            : 0
Media type                 : Sonet OC3 
Encapsulation              : atm
NAS Port Type              : 
Loopback                   : none
Framing                    : sonet
Speed                      : 155.52 Mbps
Bandwidth                  : 149.76 Mbps
Qos Rate Maximum           : Line-Rate
Tx C2 byte                 : 0x13
Rx C2 byte                 : 0x13
Line SF BER                : 10E-4
Line SD BER                : 10E-7
ATM MTU size               : 65527 Bytes
MTU size                   : 4470 Bytes
ATM Payload Scramble       : ON
Over Subscription Rate     : Unlimited
MAC address                : 00:d0:b6:ff:5b:5d
Clock Source               : card-reference
CCOD Mode                  : default
SFP Transceiver Status
Wavelength                : 1310.00 nm
Diag Monitor              : Yes  
Tx Fault                  : No Fault 
Rx Fault                  : No Fault     
Tx Pwr measured[dbm]      : -11.51 
Rx Pwr measured[dbm]      : -10.77 
Temperature               : 39 C     
Vcc Measured              : 3.23 V     
APS Group Name             : N/A
Report Only Alarms 
  Path Alarms (report only): NONE
Active Alarms              : NONE
Path Alarms                : NONE
Path Trace Length          : 64 (62 + 2 framing)
Tx Path Trace              : 
    6c616479 62756700 00000000 00000000  ladybug.........
    00000000 00000000 00000000 00000000  ................
    00000000 00000000 00000000 00000000  ................
    00000000 00000000 00000000 00000000  ................
Rx Path Trace              : 
    00000000 00000000 00000000 00000000  ................
    00000d0a 526f7574 65725465 73746572  ....RouterTester
    2e20506f 72742031 30332f31 2e000000  . Port 103/1....
    00000000 00000000 00000000 00000000  ................

The following example displays detailed port information for port 2 on a ge4-20-port line card in slot 2:

[local]Redback>show port 2/2 detail
ethernet 2/2 state is Up
Description                :
Line state                 : Up
Admin state                : Up
Link Dampening             : enabled
Link up delay              : 11000
Link down delay            : 2200
Restart link up delay      : 400
Undampened line state      : Up
Dampening Count            : 0
Encapsulation              : ethernet
MTU size                   : 1500 Bytes
NAS Port Type              :
MAC address                : 00:30:88:03:ae:6f
Media type                 : 1000Base-SX
Auto-negotiation           : on                 state: success
Duplex negotiated set      : full               state: full
Flc negotiated set         : tx&rx-or-rx-only   state: rx
force                      : disabled           state: inactive
Speed negotiated set       : 1 Gbps             state: 1 Gbps
Flow control               : rx                 state: n/a
Speed                      : 1 Gbps             state: n/a
Duplex mode                : full               state: n/a
Link Distance              : N/A
Loopback                   : off
SFP Transceiver Status
Wavelength                 : 850.00 nm
Diag Monitor               : Yes
Tx Fault                   : No Fault
Rx Fault                   : No Fault
Tx Pwr measured[dbm]       : -4.58
Rx Pwr measured[dbm]       : -3.76
Temperature                : 30 C
Vcc Measured               : 3.15 V
Active Alarms              : NONE

[local]Redback>show port 2

Slot/Port:Ch:SubCh  Type                 State
2/1                 ethernet             Up
2/2                 ethernet             Up
2/3                 ethernet             Up
2/4                 ethernet             Up
2/5                 ethernet             Up
2/6                 ethernet             Up
2/7                 ethernet             Down
2/8                 ethernet             Up
2/9                 ethernet             Up
2/10                ethernet             Up
2/11                ethernet             Up
2/12                ethernet             Down
2/13                ethernet             Up
2/14                ethernet             Up
2/15                ethernet             Up
2/16                ethernet             Up
2/17                ethernet             Up
2/18                ethernet             Up
2/19                ethernet             Down
2/20                ethernet             Up
7/1                 ethernet             Up

[local]Redback#show port 11/1 detail
ethernet 11/1 state is No card
Description                :
Line state                 : No card
Admin state                : Up
Link Dampening             : disabled
Undampened line state      : No card
Dampening Count            : 0
Encapsulation              : ethernet
MTU size                   : 1500 Bytes
NAS Port Type              :
NAS-Port-Id                :
Optical Transport          : None
Physical layer             : lan-phy
Media type                 : Unknown
Flow control               : on
Clock-Source               : local
Link Distance              : N/A
Loopback                   : off
Active Alarms              : NONE

[local]Redback#show port 11/1 detail
ethernet 11/1 state is No card
Description                :
Line state                 : No card
Admin state                : Up 
Link Dampening             : disabled
Undampened line state      : No card
Dampening Count            : 0
Encapsulation              : ethernet
MTU size                   : 1500 Bytes
NAS Port Type              :
NAS-Port-Id                :
Physical layer             : wan-phy
Media type                 : Unknown
Flow control               : on
Clock-Source               : local
Link Distance              : N/A
Loopback                   : none
Framing                    : sonet
Line SF BER                : 10E-4
Line SD BER                : 10E-7
Active Alarms              : NONE
Path Alarms                : NONE
Tx path-trace              :
    52656462 61636b00 00000000 00000000  Redback.........
Rx path-trace              :
    00000000 00000000 00000000 00000000  ................

1.16   show port perf-monitor

1.16.1   Purpose

Displays configuration information and performance-monitoring (PM) statistics for one or more ports, channels, or subchannels.

1.16.2   Command Mode

all modes

1.16.3   Syntax Description

1.16.4   Default

If no optional arguments or keywords are specified, data is for the near end.

1.16.5   Usage Guidelines

Use the show port perf-monitor command to display configuration information and PM statistics for one or more ports, channels, or subchannels.

• Table 16 lists the statistical data fields that are displayed with this command; not all fields are displayed for all types of channels and ports. If you specify the detail keyword, the same statistical data fields are displayed, but with the description instead of the abbreviation.

  Note:  

  Performance monitoring is not available for the Ethernet port type.

  
  
  • If sub-chan-num is not specified, the PM statistics are displayed for the channel specified by chan-num, and not for the individual subchannels; if sub-chan-num is specified, then the PM statistics are displayed for that channel only.
  • If you specify the far keyword for an ATM DS-3 or OC port, section data is not displayed.
  • If you have not enabled the Synchronous Optical Network (SONET) path trace and monitoring features for a first-generation ATM OC line card with the sonet eu command (in card configuration mode), path data is not displayed; it is not necessary to enter the sonet eu command for a second-generation ATM OC line card or an ATM DS-3 line card. To determine if a card has SONET path trace and monitoring features enabled, enter the show chassis command (in any mode), and check for the N flag in the Flags column.
  • Some test equipment can generate time division multiplexing (TDM) code errors such that an E3 port interprets them as a mix of excessive zeros (EXZ) and bipolar violation (BPV) errors, which usually occur in pairs; however, the E3 port considers them a single LCV error as does most legacy equipment.
• For definitions of the output status fields, see Table 15 in the description of the show port detail command.
• Data is displayed in 15-minute intervals; data for the current interval reflects the elapsed time in the interval. The same data is displayed in both the standard and detailed formats. If you do not specify the detail keyword, the data is shown in tabular format with the abbreviated field names; with the detail keyword, it is present in text format with the field descriptions.
• The SmartEdge 100 router limits the value of the slot argument to 2.

  The value for the port argument on the SmartEdge 100 router depends on the MIC slot in which the ATM OC MIC is installed.

• Table 17 lists the range of values for the chan-num and sub-chan-num arguments for various types of channelized ports.
•  

  Note:  

  By appending a space followed by the pipe ( | ) character at the end of a show command, you can filter the output using a set of modifier keywords and arguments. For more information, see “Modifying Output of show Commands” in Using the CLI.

  
  

(1)  Performance monitoring is not available for the Ethernet port type.

1.16.6   Examples

The following example displays the configuration information and PM statistics for port 1 on the ATM DS-3 line card in slot 3:

[local]Redback>show port perf-monitor 3/1

atm 3/1 state is Up
Description                :
Line state                 : Up
Admin state                : Up
Media type                 : ds3
Encapsulation              : atm
ATM MTU size               : 65527 Bytes
MTU size                   : 4470 Bytes
Loopback                   : none
Framing                    : c-bit
Framing Mode               : ADM
Speed                      : 44.736 Mbps
Bandwidth                  : 44.21 Mbps
Clock Source               : global-reference
Equipment Loopback         : customer
Cable Length               : 349 feet (short)
ATM Payload Scramble       : ON
Over Subscription Rate     : Unlimited
MAC address                : 00:30:88:12:05:01
Active Alarms              : NONE
FEAC code received         : NONE

ATMDS3 PM DATA DISPLAY

INTERVAL      LCV   PCV   CCV   PES  PSES  SEFS   UAS   LES   CES  CSES
348             0     0     0     0     0     0     0     0     0     0
Total           0     0     0     0     0     0     0     0     0     0
24 Hours        0     0     0     0     0     0     0     0     0     0

             PLCP   PLCP
INTERVAL     SEFS   UAS  LCDS
348             0     0     0
Total           0     0     0
24 Hours        0     0     0

The following example displays the configuration information and PM statistics for port 1 on the 4-port ATM OC-3/STM-1c line card in slot 11:

[local]Redback>show port perf-monitor 11/1

atm 11/1 state is Up
Description                :
Line state                 : Up
Admin state                : Up
Media type                 : Sonet OC3 (SM)
Encapsulation              : atm
Loopback                   : none
Framing                    : sonet
Speed                      : 155.52 Mbps
Bandwidth                  : 149.76 Mbps
Qos Rate Maximum           : 50 Mbps
Tx C2 byte                 : 0x13
Rx C2 byte                 : 0x13
Line SF BER                : 10E-4
Line SD BER                : 10E-7
ATM MTU size               : 65527 Bytes
MTU size                   : 4470 Bytes
ATM Payload Scramble       : ON
Over Subscription Rate     : Unlimited
MAC address                : 00:30:88:00:3f:08
Clock Source               : global-reference
Active Alarms              : NONE
Path Alarms                : NONE
Path Trace Length          : 64 (62 + 2 framing)
Tx Path Trace              :
    6b696d62 65726c79 00000000 00000000  kimberly........
    00000000 00000000 00000000 00000000  ................
    00000000 00000000 00000000 00000000  ................
    00000000 00000000 00000000 00000d0a  ................
Rx Path Trace              :
    6b696d62 65726c79 00000000 00000000  kimberly........
    00000000 00000000 00000000 00000000  ................
    00000000 00000000 00000000 00000000  ................
    00000000 00000000 00000000 00000d0a  ................

Path and Line Data
INTERVAL      PCV  PSES  PUAS   PES  LCDS   LCV  LSES  LUAS   LES
147             0     1     0     1     1     0     1     0     1
Total           0     1     0     1     1     0     1     0     1
24 Hours        0     1     0     1     1     0     1     0     1

Section Data
INTERVAL      SCV  SSES SSEFS   SES
147             0     1     1     1
Total           0     1     1     1
24 Hours        0     1     1     1

The following example displays the configuration information and PM statistics for a DS-1 channel on a port on a channelized DS-3 line card:

[local]Redback>show port perf-monitor 2/1:15
ds1 2/1:15 state is Up
Description                : 
Line state                 : Up
Admin state                : Up
Encapsulation              : cisco-hdlc
MTU size                   : 1500 Bytes
Loopback                   : none
Framing                    : ESF
Crc                        : 16
Clock Source               : global-reference
Idle Character             : flags
Timeslot                   : 1-24
Timeslot Speed             : 64
Yellow Alarm Detection     : ON
Yellow Alarm Generation    : ON
Invert Data                : OFF
Keepalive                  : Set (10 sec)
Equipment Loopback         : customer
Active Alarms              : NONE

INTERVAL      LCV   PCV   CSS  SEFS   LES    DM    ES   BES   SES   UAS
219             0     0     0     0     0     0     0     0     0     0
00:30-00:45     0     0     0     0     0     0     0     0     0     0
00:15-00:30     0     0     0     0     0     0     0     0     0     0
00:00-00:15     0     0     0     0     0     0     0     0     0     0
23:45-00:00     0     0     0     0     0     0     0     0     0     0
23:30-23:45     0     0     0     0     0     0     0     0     0     0
23:15-23:30     0     0     0     0     0     0     0     0     0     0
23:00-23:15     0     0     0     0     0     0     0     0     0     0
22:45-23:00     0     0     0     0     0     0     0     0     0     0
22:30-22:45     0     0     0     0     0     0     0     0     0     0
22:15-22:30     0     0     0     0     0     0     0     0     0     0
22:00-22:15     0     0     0     0     0     0     0     0     0     0
21:45-22:00     0     0     0     0     0     0     0     0     0     0
21:30-21:45     0     0     0     0     0     0     0     0     0     0
21:15-21:30     0     0     0     0     0     0     0     0     0     0
21:00-21:15     0     0     0     0     0     0     0     0     0     0
20:45-21:00     0     0     0     0     0     0     0     0     0     0
20:30-20:45     0     0     0     0     0     0     0     0     0     0
20:15-20:30     0     0     0     0     0     0     0     0     0     0
20:00-20:15     0     0     0     0     0     0     0     0     0     0
19:45-20:00     0     0     0     0     0     0     0     0     0     0
19:30-19:45     0     0     0     0     0     0     0     0     0     0
19:15-19:30     0     0     0     0     0     0     0     0     0     0
19:00-19:15     0     0     0     0     0     0     0     0     0     0
18:45-19:00     0     0     0     0     0     0     0     0     0     0
18:30-18:45     0     0     0     0     0     0     0     0     0     0
18:15-18:30     0     0     0     0     0     0     0     0     0     0
18:00-18:15     0     0     0     0     0     0     0     0     0     0
17:45-18:00     0     0     0     0     0     0     0     0     0     0
17:30-17:45     0     0     0     0     0     0     0     0     0     0
17:15-17:30     0     0     0     0     0     0     0     0     0     0
17:00-17:15     0     0     0     0     0     0     0     0     0     0
16:45-17:00     0     0     0     0     0     0     0     0     0     0
Total           0     0     0     0     0     0     0     0     0     0
24 Hours        0     0     0     0     0     0     0     0     0     0

1.17   show port transceiver

1.17.1   Purpose

Displays detailed information about the transceivers installed in the SmartEdge router, including their current status.

1.17.2   Command Mode

all modes

1.17.3   Syntax Description

1.17.4   Default

Displays a list of transceivers ports that are present or configured in the system.

1.17.5   Usage Guidelines

Use the show port transceiver command to display detailed information about the transceivers installed in the router, including their current status.

Table 18 describes the values for the State field that can be displayed for a given SFP or XFP transceiver port on a SmartEdge 1200, SmartEdge 800, or SmartEdge 400 router.

(1)  Use part number XFP-OC192-LR2 when ordering the XFP transceivers with 10GE ZR functionality.

(2)  In Releases 6.1.4 and 6.1.5, 10GE DWDM XFP transceivers support only ITU channels 35,36,37,53,and 54.

(3)  In Release 6.4.1, OTN-DWDM XFP transceivers support only ITU channels 35,36,37,53,and 54.

(4)  See Alarms and Probable Causes for the lists of alarms and warnings supported by the SFP and XFP transceivers.

(5)  See Table 19 for a list of auxiliary input types monitored by each auxiliary A/D channel of the XFP transceivers.

(6)  The Transceiver alarms will only be indicated here if “[no] system alarm transceiver suppress” has been configured.

Table 19 lists describes which quantities are monitored by each auxiliary A/D channel.

1.17.6   Examples

Example 1:

The following example displays the data and status for an SFP transceiver. The asterisk beside -13.01* in the Rx Pwr row indicates that the measured value is out of bounds of the Receive Power threshold and has caused a "Transceiver Receive Power Low Alarm.":

[local]Redback#show port 11/3 transceiver


SFP / Media Type        : SX / MM

Redback Approved        : YES

Diagnostic Monitoring   : YES

CLEI code               : VAUIAAWEAA

Serial Number           : F72247020031

Wavelength              : 850.00 [nm]


                                     High          High         Low          Low

                         Measured    Alarm         Warning      Alarm        Warning

------------------------------------------------------------------------------------

Tx Pwr [dbm]             -3.55      -1.00         -2.00         -9.50         -9.00

Rx Pwr [dbm]            -40.00       0.00         -1.00         -13.01*       -12.00

Temperature[C]           33          95            90           -5             0

Laser Bias Current [mA]  7.61        16.00         15.00         2.00          3.00

Vcc [V]                  3.26        3.63           3.58         2.97          3.02


Active Alarms          : Link down

                         Transceiver Receive Power Low Alarm

Example 2:

The following example displays the data and status for an XFP transceiver:

[local]Redback#show port 11/3 transceiver


XFP / Media Type        : LR / SM

Redback Approved        : NO

Diagnostic Monitoring   : YES

CLEI code               : IPUIANWCAA

Serial Number           : UDE03CT

Wavelength              : 1307.00[nm]


                                     High          High         Low          Low

                         Measured    Alarm         Warning      Alarm        Warning

------------------------------------------------------------------------------------

Tx Pwr [dbm]              -1.98       1.50         1.00         -7.00        -6.00

Rx Pwr [dbm]              -40.00      2.50         2.00         -20.00       -18.01

Temperature[C]             19         83           80           -13          -10

Laser Bias Current [mA]    35.00      80.00        75.00         15.00        20.00

AUX1 +3.3V Supply Voltage  3.31       3.63         3.50          3.00         3.10

AUX2 N/A                   N/A        N/A          N/A           N/A          N/A


Active Alarms          : Link down

1.18   show ppp

1.18.1   Purpose

Displays the states of one or more Point-to-Point Protocol (PPP) sessions.

1.18.2   Command Mode

all modes

1.18.3   Syntax Description

1.18.4   Default

Displays information for all PPP sessions in the current context.

1.18.5   Usage Guidelines

Use the show ppp command to display the states of one or more PPP sessions. For information about troubleshooting PPP, see the BRAS Troubleshooting Guide.

Note:  

The SmartEdge 100 router limits the value of the slot argument to 2.

Note:  

The value for the port argument on the SmartEdge 100 router is one of the following:

• For a native port, it is 1 or 2.
• For a MIC port, it depends on the MIC and MIC slot in which it is installed.

Note:  

The value for the port argument on the SmartEdge 100 router depends on the MIC slot in which the ATM OC MIC is installed.

Table 20 lists the range of values for the chan-num and sub-chan-num arguments for various types of channelized ports.

Table 21 lists the output fields for the show ppp command with the detail keyword.

Note:  

By default, most show commands (in any mode) display information for the current context only or, depending on the command syntax, for all contexts. If you are an administrator for the local context, you can insert the optional context ctx-name construct, preceding the show command, to view output for the specified context without entering that context. For more information about using the context ctx-name construct, see the context command description.

Note:  

By appending a space followed by the pipe ( | ) character at the end of a show command, you can filter the output using a set of modifier keywords and arguments. For more information, see “Modifying Output of show Commands” in Using the CLI.

1.18.6   Examples

The following example shows how to display summary output for PPP sessions in the current context:

[local]Redback>show ppp summary

Wed Jun 30 21:54:29 2005

               Number    LCP    IPCP   NLCP  MPLSCP

Circuit Type   Circuit   Open   Open   Open  Open

------------   -------   ----   ----   ----  ------

 mp circuits   2         2      2      0     0

ppp circuits   2         2      2      0     0



Total circuits: 4  up: 4  down: 0

The following example shows how to display detailed information for PPP sessions that are up for all ports on the line card in slot 11:

[local]Redback>show ppp 11 up detail



Wed Jun 30 16:59:38 2005

                                           LCP      IPCP     NLCP     MPLSCP 

Port/Circuit                         Unit  State    State    State    State  

------------------------------------ ----- -------- -------- -------- --------

11/1:1                                   2 Opened   Opened   Initial  

 Initial Context: local

11/2:1                                   3 Opened   Opened   Initial  

 Initial Context: remote

The following example displays output for all PPP sessions in all contexts:

[local]Redback>show ppp all 

Wed Jun 30 21:47:57 2005

                                           LCP      IPCP     NLCP     MPLSCP  

Port/Circuit                         Unit  State    State    State    State   

------------------------------------ ----- -------- -------- -------- --------

6/3                                      4 Opened   Opened   Initial  Initial 

6/4                                      5 Opened   Opened   Initial  Initial 

10/1:1                                   0 Opened   -ML-     -ML-     -ML-    

10/7:1                                   1 Opened   -ML-     -ML-     -ML-    

Link share MP                            2 N/A      Opened   Initial  Initial 

Link share MP                            3 N/A      Opened   Initial  Initial 



Total circuits: 4  up: 4  down: 0

1.19   show ppp counters

1.19.1   Purpose

Displays statistics for Point-to-Point Protocol (PPP) packets and session counters on the system.

1.19.2   Command Mode

all modes

1.19.3   Syntax Description

1.19.4   Default

If no keyword is specified, the global PPP counters are displayed.

1.19.5   Usage Guidelines

Use the show ppp counters command to display statistics for PPP packets and session counters on the system.

Note:  

By default, most show commands (in any mode) display information for the current context only or, depending on the command syntax, for all contexts. If you are an administrator for the local context, you can insert the optional context ctx-name construct, preceding the show command, to view output for the specified context without entering that context. For more information about using the context ctx-name construct, see the context command description.

Note:  

By appending a space followed by the pipe ( | ) character at the end of a show command, you can filter the output using a set of modifier keywords and arguments. For more information, see “Modifying Output of show Commands” in Using the CLI. For information about troubleshooting PPP, see the BRAS Troubleshooting Guide.

1.19.6   Examples

The following example shows how to display the context-specific PPP counters for the current context:

[local]Redback>show ppp counters context

Last cleared: Never

     received: bytes 260, packets 26,

               unsupported packets 0

         sent: bytes 260, packets 26

LCP echo request      : received 26, sent 0, dropped 0

LCP echo response     : received 0, sent 26, dropped 0

LCP protocol reject   : received 0, sent 0, dropped 0

The following example shows how to display global PPP counters:

[local]Redback>show ppp counters



Wed Jun 30 21:56:07 2005

Packet--------------------------------------------------------

 In                       285      Out                     287

Session-------------------------------------------------------

 LCP Up                    72      LCP Down                 68

 IPCP Up                   12      IPCP Down                 6

 Authen Success             0      Authen Failure            0

 Session Up                 0      Session Down              0

SessionControl------------------------------------------------

 Starting                   0      Authenticating            0

 Pended (current)           0      Pended (total)            0

 Packet Drop

  Session pended            0      At Limit                  0

Timeout-------------------------------------------------------

 ConfReq                   85      TermReq                  19

 CHAP Challenge             0      UPAP Listen               0

PacketDropIn--------------------------------------------------

 Session is Down           17      Bad FSM State            32

The following example shows how to display detailed information for global PPP counters:

[local]Redback>show ppp counters detail

Packet--------------------------------------------------------

 In                        40     Out                      40

  ConfReq                  24      ConfReq                 10

  ConfAck                  10      ConfAck                 10

  ConfNak                   0      ConfNak                  4

  ConfRej                   0      ConfRej                 10

  TermReq                   4      TermReq                  2

  TermAck                   2      TermAck                  4

  Authen Proto              6      Authen Proto             6

  other                     0      other                    0

Session-------------------------------------------------------

 LCP Up                     6     LCP Down                  6

 IPCP Up                    4     IPCP Down                 4

 Authen Success             4     Authen Failure            2

 Session Up                 4     Session Down              6

SessionControl------------------------------------------------

 Starting                   0     Authenticating            0

 Pended (current)           0     Pended (total)            0

 Packet Drop

 Session pended             0     At Limit                  0

Timeout-------------------------------------------------------

 ConfReq                    0     TermReq                   4

 CHAP Challenge             0     UPAP Listen               0

PacketDropIn--------------------------------------------------

 Session is Down            1     Bad FSM State             0

DownCause-----------------------------------------------------

 Rcvd TermReq               4     Rcvd PPPoE PADT           0

 No ConfReq Resp            0     No Echo Resp              0

 Authen Failed              2     Session Down              0

 LCP Down                   0     Circuit Down              0

 Port Down                  0     Port Delete               0

1.20   show ppp multilink

1.20.1   Purpose

Displays information for Multilink Point-to-Point Protocol (MP) bundles.

1.20.2   Command Mode

all modes

1.20.3   Syntax Description

1.20.4   Default

When used without any optional constructs, displays information about all MP bundles in the current context.

1.20.5   Usage Guidelines

Use the show ppp multilink command to display information for MP bundles.

Use the bundle-name argument to specify an MP bundle configured with DS-1 channels, E1 channels, or E1 ports; use the mp sess-id construct to specify an MP bundle created by the system on a PPP-encapsulated or PPP over Ethernet (PPPoE)-encapsulated circuit.

To determine the session ID for an MP bundle, use the show ppp all or show circuit command (in any mode).

Note:  

By default, most show commands (in any mode) display information for the current context only or, depending on the command syntax, for all contexts. If you are an administrator for the local context, you can insert the optional context ctx-name construct, preceding the show command, to view output for the specified context without entering that context. For more information about using the context ctx-name construct, see the context command description.

Note:  

By appending a space followed by the pipe ( | ) character at the end of a show command, you can filter the output using a set of modifier keywords and arguments. For more information, see “Modifying Output of show Commands” in Using the CLI. For information about troubleshooting PPP, see the BRAS Troubleshooting Guide.

1.20.6   Examples

The following example shows how to display information for any MP bundle:

[local]Redback>show ppp multilink

Bundle Name: bar             

  Link Count: 2  Username: (null)

  Our MRRU: 1524 Peer MRRU: 1524

  Our Endpoint-Discriminator: class-1 Redback

  Peer Endpoint-Discriminator: class-1 Redback

Member Links      Status

  5/3             active

  5/1             active

The Link Count field displays the number of links that are up.

The following example shows how to display information for all link groups in all contexts:

[local]Redback>show ppp multilink all

Bundle Name: bar             

  Link Count: 2  Username: (null)

  Our MRRU: 1524 Peer MRRU: 1524

  Our Endpoint-Discriminator: class-1 Redback

  Peer Endpoint-Discriminator: class-1 Redback

 

  Member Links     Status

  5/3              active

  5/1              active

 

Bundle Name: bar2            

  Link Count: 2  Username: (null)

  Our MRRU: 1524 Peer MRRU: 1524

  Our Endpoint-Discriminator: class-1 Redback

  Peer Endpoint-Discriminator: class-1 Redback

 

  Member Links     Status

  5/4              active

  5/2              active

The following example shows how to display summary information only:

[local]Redback>show ppp multilink summary

Wed Jun 30 06:38:05 2005

               NUMBER    LCP    IPCP   NLCP

CIRCUIT TYPE   CIRCUIT   OPEN   OPEN   OPEN

------------   -------   ----   ----   ----

 mp circuits   24        24     3      0   

ppp circuits   0         0      0      0   



Total circuits: 24  up: 24  down: 0

The following example shows how to display information for the bar MP bundle, which is a link group of E1 ports:

[local]Redback>show ppp multilink bundle bar

Bundle Name: bar             

  Link Count: 2  Username: (null)

  Our MRRU: 1524 Peer MRRU: 1524

  Our Endpoint-Discriminator: class-1 Redback

  Peer Endpoint-Discriminator: class-1 Redback

 

  Member Links      Status

  5/3               active

  5/1               active

The following example shows how to display information for an MP bundle on an ATM PVC, using its session ID:

[local]Redback>show ppp multilink bundle mp 1

Bundle Name: MP 1            

  Link Count: 1  Username: a-32@local

  Our MRRU: 1524 Peer MRRU: 1524

  LFI Fragment-Threshold: 256

  Our Endpoint-Discriminator: class-3 00:30:88:00:04:5b

  Peer Endpoint-Discriminator: class-2 10.12.48.103

 

  Member Links                         Status

  3/1 vpi-vci 0 32                     active

The following example shows how to display information about the MP bundle named abc. Because the command includes the detail keyword, the output provides both the bundle handle (Acct handle) and circuit handle (cct handle) information. Note also that 6/1:1:1 under Member Links provides the port/slot:channel:subchannel of the master link:

[local]Redback>show ppp multilink bundle abc detail

Bundle Name: abc

   Link Count: 1  Username:

   Our MRRU: 1500  Peer MRRU: 1500

   Our Endpoint-Discriminator: class-1 dino

   Peer Endpoint-Discriminator: class-1 dino

   Acct handle: 255/7:1023:63/1/1/2


   Member Links                         Status

   6/1:1:1                              active (master)

   cct handle  : 6/1:1:1/1/1/19

1.21   show pppoe

1.21.1   Purpose

Displays Point-to-Point Protocol over Ethernet (PPPoE) information for one or more subscriber circuits.

1.21.2   Command Mode

• all modes

1.21.3   Syntax Description

1.21.4   Default

None

1.21.5   Usage Guidelines

Use the show pppoe command to display PPPoE-related information for one or more circuits.

Note:  

The SmartEdge 100 router limits the value of the slot argument to 2.

Note:  

The value for the port argument on the SmartEdge 100 router is one of the following:

• For a native port, it is 1 or 2.
• For a MIC port, it depends on the MIC and MIC slot in which it is installed.

Table 22 lists the values for the circuit-id argument.

Note:  

By default, most show commands (in any mode) display information for the current context only or, depending on the command syntax, for all contexts. If you are an administrator for the local context, you can insert the optional context ctx-name construct, preceding the show command, to view output for the specified context without entering that context. For more information about using the context ctx-name construct, see the context command description.

Note:  

By appending a space followed by the pipe ( | ) character at the end of a show command, you can filter the output using a set of modifier keywords and arguments. For more information, see “Modifying Output of show Commands” in Using the CLI. For information about troubleshooting PPPoE, see the BRAS Troubleshooting Guide.

1.21.6   Examples

The following example shows how to display summary information:

[local]Redback>show pppoe summary

               NUMBER

CIRCUIT TYPE   CIRCUIT   UP    DOWN

------------   ------- ------ ------

ATM            3         3        0

ETHERNET       0         0        0

DOT1Q          0         0        0

Total circuits: 3 up: 3 down: 0

The following example shows how to display services information:

[local]Redback>show pppoe services

Context: local

Number of domains: 2

        Domain: adsl (not advertise)

        Domain: redback (not advertise)

Context: one

Number of domains: 1

        Domain: pppoe (not advertise)

The following example shows how to display information for all PPPoE circuits in the local context:

[local]Redback>show pppoe

Wed Jun 30 01:38:42 2005

Circuit                             MAC address       Subscriber

----------------------------------------------------------------------

3/1 vpi-vci 0 32 pppoe 2001         00:10:67:00:2a:01 a-32@local

3/1 vpi-vci 0 33 pppoe 2002         00:10:67:00:2a:02 a-33@local

3/1 vpi-vci 0 34 pppoe 2003         00:10:67:00:2a:03 a-34@local

1.22   show pppoe counters

1.22.1   Purpose

Displays summary or detailed statistics for all Point-to-Point Protocol (PPP) over Ethernet (PPPoE)-encapsulated circuits.

1.22.2   Command Mode

all modes

1.22.3   Syntax Description

1.22.4   Default

None

1.22.5   Usage Guidelines

Use the show pppoe counters command to display summary or detailed statistics for all PPPoE-encapsulated circuits.

Note:  

By default, most show commands (in any mode) display information for the current context only or, depending on the command syntax, for all contexts. If you are an administrator for the local context, you can insert the optional context ctx-name construct, preceding the show command, to view output for the specified context without entering that context. For more information about using the context ctx-name construct, see the context command description.

Note:  

By appending a space followed by the pipe ( | ) character at the end of a show command, you can filter the output using a set of modifier keywords and arguments. For more information, see “Modifying Output of show Commands” in Using the CLI. For information about troubleshooting PPPoE, see the BRAS Troubleshooting Guide.

1.22.6   Examples

The following example shows how to display summary statistics:

[local]Redback>show pppoe counters

Wed Jun 30 01:37:25 2005

PPPoE PAD counters:

-------------------

sent packets             : 4000         recv packets : 4000

dropped packets          : 0

PADI packets             : 2000         PADO packets : 2000

PADR packets             : 2000         PADS packets : 2000

PADT packets             : 0            PADM packets : 0

PADN packets             : 0

The following example shows how to display detailed statistics:

[local]Redback>show pppoe counters detail

Wed Jun 30 08:30:40 2005



PPPoE PAD counters:

-------------------

sent packets             : 4000         recv packets             : 4000

dropped packets          : 0         

PADI packets             : 2000         PADO packets             : 2000

PADR packets             : 2000         PADS packets             : 2000

PADT packets             : 0            PADM packets             : 0   

PADN packets             : 0         



PPPoE invalid discovery packet counters:

----------------------------------------

invalid version/type     : 0            invalid length           : 0   

invalid tag length       : 0            unknown code             : 0   

PADIs non-zero sess-id   : 0            PADRs non-zero sess-id   : 0   

PADT, bad MAC addr       : 0            bad encaps               : 0   

PADR, max sess reached   : 0            PADR, same MAC           : 0   

tags not added, large pkt: 0            recv on down circuit     : 0   

invalid tag name         : 0            invalid tag name accepted: 0   

circuit not created      : 0            circuit not init         : 0   

packet on virtual circuit: 0            non subscriber circuit   : 0   

unknown circuit          : 0            proc restart drops       : 0   



PPPoE virtual circuit counters:

-------------------------------

created virtual circuits : 0            deleted virtual circuits : 0   

combined circuits used   : 4000         combined circuits reset  : 2000

create failed            : 0            delete failed            : 0   

create fail, rcct used   : 0            create fail, no cct      : 0   

create fail, cct init    : 0            create fail, vcct exists : 0   

circuit lookup failures  : 0         



PPPoE PADM error counters:

--------------------------

malformed URLs           : 0            too long expanded URLs   : 0   

too long MOTMs           : 0            bad expansion char       : 0   

PADX on bad circuit      : 0         



PPPoE session counters:

-----------------------

session down cplt recv   : 2000         session down cplt proc   : 2000

stale entry cleanup      : 0            bad state entry cleanup  : 0   

session down sent        : 0 

1.23   show privilege

1.23.1   Purpose

Displays the current privilege level for the current exec session.

1.23.2   Command Mode

• all modes

1.23.3   Syntax Description

This command has no keywords or arguments.

1.23.4   Default

None

1.23.5   Usage Guidelines

Use the show privilege command to display the current (administrator) privilege level for the current exec session.

If you are an administrator at privilege level 10 or higher, you can determine the privilege level of any given command at your level or lower by recursively entering the enable and show ? commands.

For example, if an administer at privilege level 15 enters the show privilege command, all commands at privilege level 15 and lower are listed. If the administrator then enters the enable command for privilege level 14 and the show privilege command again, all commands at privilege level 14 and lower are listed. The administrator can repeat these steps at levels 13, 12, and so on until all privilege levels are listed.

Be aware that this method lists the current privilege levels, which could be different from the default privilege levels. See the privilege command in the Command List for more information.

Note:  

By default, most show commands (in any mode) display information for the current context only or, depending on the command syntax, for all contexts. If you are an administrator for the local context, you can insert the optional context ctx-name construct, preceding the show command, to view output for the specified context without entering that context. For more information about using the context ctx-name construct, see the context command description.

Note:  

By appending a space followed by the pipe ( | ) character at the end of a show command, you can filter the output using a set of modifier keywords and arguments. For more information, see “Modifying Output of show Commands” in Using the CLI.

1.23.6   Examples

The following example displays output from the show privilege command:

[local]Redback>show privilege

Current privilege level is 6

1.24   show process

1.24.1   Purpose

Displays current status of one or all processes running on the system.

1.24.2   Command Mode

all configuration modes

1.24.3   Syntax Description

1.24.4   Default

When used without any optional constructs, this command displays summary status of all tasks running.

1.24.5   Usage Guidelines

Use the show process command to display current information on a specific category of processes, or on all running processes.

Table 23 lists the keywords for the processes supported by this command.

(1)  The SmartEdge 100 router does not support 802.1Q.

(2)  Not all controller cards support flow.

(3)  The SmartEdge 100 router does not support Frame Relay.

Note:  

By default, most show commands (in any mode) display information for the current context only or, depending on the command syntax, for all contexts. If you are an administrator for the local context, you can insert the optional context ctx-name construct, preceding the show command, to view output for the specified context without entering that context. For more information about using the context ctx-name construct, see the context command description.