SNMP MIB Notifications

Contents

1SNMP MIB Notifications
1.1Setting up SNMP Alarm Models for Notifications

2

AAA Notifications

3

Bridge Notifications

4

DHCP Notifications

5

Entity Notifications

6

Environmental Notifications
6.1Descriptions and Object Identifiers

7

IP Pool Notifications

8

L2TP Notifications

9

L2VPN Cross-Connection (XC) Notifications

10

Link and Interface Notifications
10.1Descriptions and Object Identifiers

11

Media Gateway Notifications

12

RMON Notifications

13

Routing Notifications
13.1Descriptions and Object Identifiers

14

System Management Notifications
14.1dot1agCfmFaultAlarm Example

15

System Resource Notifications

16

System Security Notifications

17

System Services Engine (SSE) Notifications
Copyright

© Ericsson AB 2009–2011. All rights reserved. No part of this document may be reproduced in any form without the written permission of the copyright owner.

Disclaimer

The contents of this document are subject to revision without notice due to continued progress in methodology, design and manufacturing. Ericsson shall have no liability for any error or damage of any kind resulting from the use of this document.

Trademark List
SmartEdge is a registered trademark of Telefonaktiebolaget LM Ericsson.
NetOp is a trademark of Telefonaktiebolaget LM Ericsson.

1   SNMP MIB Notifications

The SmartEdge® router supports the notifications for IETF-standard Management Information Bases (MIBs) and enterprise MIBs described in the following sections.

For a list of MIBs supported by the SmartEdge router, including enterprise MIBs, see Standard SNMP MIBs.

Note:  
Simple Network Management Protocol (SNMP) examples in this document utilize the open source tool Net-SNMP. Depending on the product you use to monitor your network, the examples may appear different from your system.

1.1   Setting up SNMP Alarm Models for Notifications

You can use ALARM-MIB to create alarm models to specify the types of alarms and alarm states to raise for existing notifications. To configure an alarm model:

  1. Use the snmp alarm command to enter the SNMP alarm model command mode.
  2. Use one of the following commands to set up the SNMP alarm model with additional parameters:
  3. Use the following show commands to display information about SNMP alarm models:
    • show snmp alarm model to display information about each alarm model.
    • show snmp alarm active to display information about active alarm models.
    • show snmp alarm cleared to display information about cleared alarm models.
    • show snmp alarm stats to display general statistics about all alarm models, including how many have been configured.
  4. Enable debugging for snmp alarm models by using the debug snmp mib alarm command.

2   AAA Notifications

Table 1 lists notifications generated by the router to indicate Authentication, Authorization and Accounting (AAA) notifications as defined in the RBN-SUBSCRIBER-ACTIVE-MIB, the RBN-TACACS-MIB, and the RBN-RADIUS-MIB.

Table 1    AAA Notifications

Event and OID

Description and Cause

Recommended Action

Reporting Module

Severity(1)

Related Events and Commands

rbnRadiusAcctStateChange


1.3.6.1.4.1.2352.2.32.0.2


RBN-RADIUS-MIB

The system raises this event when a RADIUS accounting server transitions to the down state. The system clears this event when a RADIUS server transitions to the up state(2)


Cause: The connection to the RADIUS server is established (cleared) or lost (raised).

Ensure that the correct RADIUS configuration appears and that IP and link connectivity is available and free of errors between the SER and the RADIUS server.

Context

Warning

Event: None


Command: None

rbnRadiusAuthStateChange


1.3.6.1.4.1.2352.2.32.0.1


RBN-RADIUS-MIB

The system raises this event when a RADIUS authorization server transitions to the down state. The system clears this event when a RADIUS server transitions to the up state(3)


Cause: The connection to the RADIUS server is established (cleared) or lost (raised).

Ensure that the correct RADIUS configuration appears and that IP and link connectivity is available and free of errors between the SER and the RADIUS server.

Context

Warning

Event: None


Command: None

rbnSubsConfigErrorEvent


1.3.6.1.4.1.2352.2.27.3.0.1


RBN-SUBSCRIBER-ACTIVE-MIB

The system raises this event when the subscriber session receives one or more policy names from the AAA server. The policy is not defined in the node configuration, and the subscriber session is allowed to come up.


Cause: A subscriber AAA record is referring to an undefined policy on the node.

Define the policy on the node or change the policy in AAA server for the subscriber.

Context

Warning

Event: None


Command: None

rbnTacacsStateChange


1.3.6.1.4.1.2352.2.33.0.1


RBN-TACACS-MIB

The system raises this event when a TACACS+ authorization server transitions to the down state. The system clears this event when a RADIUS server transitions to the up state.(4)


Cause: The connection to the TACACS+ server is established (cleared) or lost (raised).

Ensure that the correct TACACS+ configuration appears and that IP and link connectivity is available and free of errors between the SER and the TACACS+ server.

Context

Warning

Event: None


Command: None

(1)  The recommended severity level.

(2)  If the value of the rbnRadiusAcctSrvState object is down and the value of the rbnRadiusReason object is packetTimeout, then the value of the rbnRadiusUsername object is a username. Otherwise, the value of the rbnRadiusUsername object is a zero-length string.

(3)  If the value of the rbnRadiusAuthSrvState object is down and the value of the rbnRadiusReason object is packetTimeout, the value of the rbnRadiusUsername object is a username. Otherwise, the value of the rbnRadiusUsername object is a zero-length string.

(4)  If the value of the rbnTacacsState object is down and the value of the rbnTacacsReason object is packetTimeout, the value of the rbnTacacsUserName object is a username. Otherwise, the value of the rbnTacacsUserName object is a zero-length string. If value of the rbnTacacsServerReason object is serverError, the rbnTacacsServerMsg object may contain a string from the server; otherwise, the value is a zero-length string.


Table 2 describes the objects for AAA notifications.

Table 2    AAA Objects

Notification

Object

rbnRadiusAcctStateChange


RBN-RADIUS-MIB

rbnRadiusAcctSrvState:


  • 1 unknown—The state on initial creation.

  • 2 up—The server is responding.

  • 3 down—The server is not responding.

radiusAccServerAddress


IpAddress

radiusAccClientServerPortNumber


IpAddress

rbnRadiusClientPort


Unsigned32 (1024..65535)

rbnRadiusContext


SnmpAdminString (SIZE (1..63))

rbnRadiusReason:


  • 1 Responding—The server is responding.
    Valid for a transition to up

  • 2 PacketTimeout—The server is not responding and a packet-level timeout has occurred.
    Valid for a transition to down

  • 3 serverTimeout—The server is not responding and a server-level time-out has occurred.
    Valid for a transition to down

  • 4 portDown—The physical port used to access the server has been shutdown.
    Valid for a transition to down

rbnRadiusUsername


SnmpAdminString (SIZE (0..128))

rbnRadiusAuthStateChange


RBN-RADIUS-MIB

rbnRadiusAuthSrvState:


  • 1 unknown—The state on initial creation.

  • 2 up—The server is responding.

  • 3 down—The server is not responding.

radiusAuthServerAddress


IpAddress

radiusAuthClientServerPortNumber


IpAddress

rbnRadiusClientPort


Unsigned32 (1024..65535)

rbnRadiusContext


SnmpAdminString (SIZE (1..63))

rbnRadiusReason:


  • 1 Responding—The server is responding.
    Valid for a transition to up

  • 2 PacketTimeout—The server is not responding and a packet-level timeout has occurred.
    Valid for a transition to down

  • 3 serverTimeout—The server is not responding and a server-level time-out has occurred.
    Valid for a transition to down

  • 4 portDown—The physical port used to access the server has been shutdown.
    Valid for a transition to down

rbnRadiusUsername


SnmpAdminString (SIZE (0..128))

rbnSubsConfigErrorEvent


RBN-SUBSCRIBER-ACTIVE-MIB

rbnSubsActiveCircuitHandle


Octet String (Size (8))

rbnSubsConfigErrorMsgs


SnmpAdminString

rbnTacacsStateChange


RBN-TACACS-MIB

rbnTacacsContext


SnmpAdminString (SIZE (1..63))

rbnTacacsServerIndex


Unsigned32 (1..4294967295)

rbnTacacsServerAddressType


InetAddressType:


  • 0—Unknown

  • 1—Ipv4

  • 2—Ipv6

  • 16—Dns

rbnTacacsServerAddress


Octet String (Size (0..255))

rbnTacacsServerPort


Unsigned32(0..65535)

rbnTacacsServerState


RbnTacacsState


Integer:


  • 1 unknown—The state on initial creation.

  • 2 up—The server is responding.

  • 3 down—The server is not responding.

rbnTacacsServerReason


RbnTacacsReason


Integer:


  • 1 responding—The server is responding.
    Valid for a transition to up

  • 2 packetTimeout—The server is not responding and a packet-level timeout has occurred.
    Valid for a transition to down

  • 3 serverTimeout—The server is not responding and a server-level time-out has occurred.
    Valid for a transition to down

  • 4 serverError—The server has an error resulting in a transition to down state.
    Valid for a transition to down

rbnTacacsUserName


SnmpAdminString (SIZE (0..128))

rbnTacacsServerMsg


SnmpAdminString (SIZE (0..256))

3   Bridge Notifications

Table 3 lists notifications generated by the router to indicate bridge notifications as defined in the RBN-BRIDGE-MIB.

Table 3    Bridge Notifications

Event and OID

Description and Cause

Recommended Action

Reporting Module

Severity

Related Events and Commands

rbnBridgeCctStateEvent


1.3.6.1.4.1.2352.2.42.0.1


RBN-BRIDGE-MIB

The system raises this event when a loop has been detected (which locks the bridge circuit) and clears the event when the loop is cleared.


Data traffic may be dropped during inconsistent state.


Cause: A loop among bridge circuits has been detected. One or more circuits are in inconsistent forwarding state.

If this trap raises regularly, check the bridge configuration and network connection for inconsistency.

Bridge

Warning

Event: None


Command: None

rbnBridgeNewRootEvent


1.3.6.1.4.1.2352.2.42.0.2


RBN-BRIDGE-MIB

The system raises this event when the sending agent has become the new root of the spanning tree.


Cause: The trap is sent by a bridge after its election as the new root.

None

Bridge

Informational

Event: None


Command: None

rbnBridgeTopologyChangeEvent


1.3.6.1.4.1.2352.2.42.0.3


RBN-BRIDGE-MIB

The system raises this event when configured ports on a bridge transition from the learning state to the forwarding state, or from the forwarding state to the blocking state.


Cause: The port transitions from the learning state to the forwarding state, or from the forwarding state to the blocking state

None. This is for information only.

Bridge

Informational

Event: None


Command: None

Table 4 describes the objects for bridge notifications.

Table 4    Bridge Objects

Notification

Objects and Values

rbnBridgeCctStateEvent


RBN-BRIDGE-MIB

rbnBridgeGroupName


SnmpAdminString (SIZE(1..32))

rbnBridgeCircuitDescriptor


SnmpAdminString (SIZE (1..255))

rbnBridgeCircuitStatus


Integer:


  • 1—blocked

  • 2—cleared

rbnBridgeGroupContextName


SnmpAdminString (SIZE(1..64))

rbnBridgeNewRootEvent


RBN-BRIDGE-MIB

rbnBridgeId


Integer32 (1..65535)

dot1dStpPortState


Integer:


  • 1—disabled

  • 2—blocking

  • 3—listening

  • 4—learning

  • 5—forwarding

  • 6—broken

rbnBridgeTopologyChangeEvent


RBN-BRIDGE-MIB

rbnBridgeId


Integer32 (1..65535)

dot1dStpPortState


Integer:


  • 1—disabled

  • 2—blocking

  • 3—listening

  • 4—learning

  • 5—forwarding

  • 6—broken

rbnBridgePortPreviousState


Integer:


  • 1—disabled

  • 2—blocking

  • 3—listening

  • 4—learning

  • 5—forwarding

  • 6—broken

4   DHCP Notifications

Table 5 lists notifications generated by the router to indicate Dynamic Host Configuration Protocol (DHCP) notifications as defined in the RBN-DHCP-MIB.

Table 5    DHCP Notifications

Event and OID

Description and Cause

Recommended Action

Reporting
Module

Severity

Related Events and Commands

rbnDhcpIntfThresholdFallingThresholdMet


1.3.6.1.4.1.2352.2.30.0.1


RBN-DHCP-MIB

A notification indicating that a per-interface falling threshold has been reached.

Falling threshold events are enabled if either or both of rbnDhcpIntfThresholdFallingSendTrap and rbnDhcpIntfThresholdFallingLogMessage are true.

Node
(Context)

Major

Event: None


Command: None

rbnDhcpIntfThresholdRisingThresholdMet


1.3.6.1.4.1.2352.2.30.0.2


RBN-DHCP-MIB

A notification indicating that a per-interface rising threshold has been reached.

Rising threshold events are enabled if either or both of rbnDhcpIntfThresholdRisingSendTrap and rbnDhcpIntfThresholdRisingLogMessage are true.

Node
(Context)

Major

Event: None


Command: None

rbnDhcpCtxThresholdFallingThresholdMet


1.3.6.1.4.1.2352.2.30.0.3


RBN-DHCP-MIB

The system clears this event when it reaches the threshold of a context falling.


Cause: The leases for each context are below the defined threshold.

Check if there are any connectivity problems that might prevent leases from succeeding.

Node
(Context)

Major

Event: rbnDhcpCtxThresholdRisingThresholdMet


Command: None

rbnDhcpCtxThresholdRisingThresholdMet


1.3.6.1.4.1.2352.2.30.0.4


RBN-DHCP-MIB

The system raises this event when it reaches the threshold of a context falling.


Cause: The leases for each context are below the defined threshold.

Configure more DHCP ranges if subnets become exhausted. Ensure that you configure the lease-time commands (default-lease-time, offer-lease-time, and max-lease-time) and dhcp max-addrs commands to prevent over-utilization of available addresses.

Node
(Context)

Major

Event: rbnDhcpCtxThresholdFallingThresholdMet


Command: None

rbnDhcpRangeThresholdFallingThresholdMet


1.3.6.1.4.1.2352.2.30.0.5


RBN-DHCP-MIB

The system clears this event when it reaches the per-subnet falling threshold.


Cause: The leases for each subnet are lower than the defined threshold.

Check any connectivity problems that can prevent leases from succeeding.

Node
(IP pool)

Major

Event: rbnDhcpRangeThresholdRisingThresholdMet


Command: None

rbnDhcpRangeThresholdRisingThresholdMet


1.3.6.1.4.1.2352.2.30.0.6


RBN-DHCP-MIB

The system raises this event when it reaches the per-subnet falling threshold.


Cause: The leases for each subnet are lower than the defined threshold.

One subnet may be nearing exhaustion of available IP addresses. Other subnets are available for DHCP unless you receive the context threshold alarm.

Node
(IP pool)

Major

Event: rbnDhcpRangeThresholdFallingThresholdMet


Command: None

Table 6 describes the objects for DHCP notifications.

Table 6    DHCP Objects

Notification

Objects and Values

rbnDhcpIntfThresholdFallingThresholdMet


RBN-DHCP-MIB

rbnDhcpIntfThresholdContextName


SnmpAdminString (SIZE (0..63))

rbnDhcpIntfThresholdAvailable


Unsigned32

rbnDhcpIntfThresholdFallingThreshold


Unsigned32 (0..196608)

rbnDhcpIntfThresholdRisingThresholdMet


RBN-DHCP-MIB

rbnDhcpIntfThresholdContextName


SnmpAdminString (SIZE (0..63))

rbnDhcpIntfThresholdAvailable


Unsigned32

rbnDhcpIntfThresholdRisingThreshold


Unsigned32 (0..196608)

rbnDhcpCtxThresholdFallingThresholdMet


RBN-DHCP-MIB

rbnDhcpCtxThresholdName


SnmpAdminString (SIZE (0..63))

rbnDhcpCtxThresholdAvailable


Unsigned32

rbnDhcpCtxThresholdFallingThreshold


Unsigned32 (0..196608)

rbnDhcpCtxThresholdRisingThresholdMet


RBN-DHCP-MIB

rbnDhcpCtxThresholdName


SnmpAdminString (SIZE (0..63))

rbnDhcpCtxThresholdAvailable


Unsigned32

rbnDhcpCtxThresholdRisingThreshold


Unsigned32 (0..196608)

rbnDhcpRangeThresholdFallingThresholdMet


RBN-DHCP-MIB

rbnDhcpRangeThresholdContextName


SnmpAdminString (SIZE (0..63))

rbnDhcpRangeThresholdInterfaceName


SnmpAdminString (SIZE (1..80))

rbnDhcpRangeThresholdEndAddr


IpAddress

rbnDhcpRangeThresholdAvailable


Unsigned32

rbnDhcpRangeThresholdFallingThreshold


Unsigned32 (0..196608)

rbnDhcpRangeThresholdRisingThresholdMet


RBN-DHCP-MIB

rbnDhcpRangeThresholdContextName


SnmpAdminString (SIZE (0..63))

rbnDhcpRangeThresholdInterfaceName


SnmpAdminString (SIZE (1..80))

rbnDhcpRangeThresholdEndAddr


IpAddress

rbnDhcpRangeThresholdAvailable


Unsigned32

rbnDhcpRangeThresholdRisingThreshold


Unsigned32 (0..196608)

5   Entity Notifications

Table 7 lists notifications generated by the router to indicate Entity Notifications as defined in RFC 2037, Entity MIB using SMIv2 and the RBN-CARDMON-MIB and the RBN-NOTIFY-ENHANCE-MIB.

Table 7    Entity Notifications

Event and OID

Description and Cause

Recommended Action

Reporting Module

Severity

Related Events and Commands

entConfigChange


1.3.6.1.2.1.47.2.0.1


ENTITY-MIB

The system generates this event when the entity configuration changes. It can be utilized by a Network Management System (NMS) to trigger logical and physical entity table maintenance polls.


This notification signifies that a physical entity of a chassis changed in the last 5 seconds (for example, card addition or removal), and the SNMP manager can reread the entity and act on the change.


Cause: Hardware has been inserted or removed, or a card has failed.

Use the show hardware, show diag, and show log commands to identify any failed or missing hardware.

Node

Minor

Events:


  • coldStart

  • cardAlarm


Command: None

rbnNEentConfigChange


1.3.6.1.4.1.2352.2.36.0.1


RBN-NOTIFY-ENHANCE-MIB

The system generates this event when the entity configuration changes. It can be utilized by an NMS to trigger logical and physical entity table maintenance polls.


This is an enhanced version of entConfigChange trap defined in ENTITY-MIB. Use the traps nemib {exclusive | non-exclusive} command to enable this notification.


Cause: Hardware has been inserted or removed, or a card has failed.

Use the show hardware, show diag, and show log commands to identify any failed or missing hardware.

Card on the Node

Minor

Events:


  • coldStart

  • cardAlarm


Command: traps nemib {exclusive | non-exclusive}

rbnCardAlarm


1.3.6.1.4.1.2352.2.31.0.


RBN-CARDMON-MIB

The system raises or clears this event when an event occurs on a controller or traffic card.


Cause: An alarm has been raised or cleared on a controller, system, or I/O card.

Dependent upon which notification raised and installed hardware. See individual traps for troubleshooting steps.

Device

Warning

Event: None


Command: None

rbnNECardAlarm


1.3.6.1.4.1.2352.2.36.0.2


RBN-NOTIFY-ENHANCE-MIB

The system raises or clears this event when an event occurs on a controller or traffic card.


This is an enhanced version rbnCardAlarm trap defined in the RBN-CARDMON-MIB


Cause: An alarm has been raised or cleared on a controller, system, or I/O card.

Dependent upon which notification raised and installed hardware. See individual traps for troubleshooting steps.

Card

Warning

Event: None


Command: traps nemib {exclusive | non-exclusive}

rbnSfpAlarm


1.3.6.1.4.1.2352.2.49.0.1


RBN-SFP-MIB

The system raises or clears this notification when an SFP or XFP tranceiver changes status.

This notification is cleared when the defective SFP or XFP tranceiver is replaced in the port.

Port

Major or Warning

Event: None


Command: system alarm tranceiver suppress

Table 8 describes the objects for system management notifications.

Table 8    Entity Objects

Notification

Objects and Values

entConfigChange


ENTITY-MIB

See RFC 2037, Entity MIB using SMIv2 .

rbnNEentConfigChange


RBN-NOTIFY-ENHANCE-MIB

rbnNESlot


Unsigned32 (0..255)

rbnNECardName


DisplayString (SIZE (0..255))

rbnNECardOp:


  • 1—insert

  • 2—remove

  • 3—other

sysName


DisplayString (SIZE (0..255))

rbnCardAlarm


RBN-CARDMON-MIB

rbnCardAlarmId:


  • 1—unknown

  • 2—cpFail—Circuit pack failure

  • 3—cpBackplaneFail—Circuit pack backplane failure

  • 4—diagFail—Diagnostic failure

  • 5—voltageFail—Voltage failure

  • 6—controllerSwitchFail—Controller switch failure

  • 7—controllerTempCritical—Controller temp critical

  • 8—controllerFail—Controller failure

  • 9—controllerDiagFail—Controller diag test failure

  • 10—cpPowerOnDiagFail—Circuit pack power-on—diagnostic failure

  • 11—controllerPowerOnDiagFail—Controller power-on—diagnostic failure

  • 12—cpOverheat—Circuit pack overheat

  • 13—controllerOverheat

  • 14—backplaneclkfail

  • 15—btciferror

  • 16—btcnotready

  • 17—cpbackplanedegrade

  • 18—cpcardcodemismatch

  • 19—cpmismatch

  • 20—cpmissing

  • 21—cpresetcomplete

  • 22—downloadcompleted

  • 23—downloadfailed

  • 24—syncfail

  • 25—backupfail

  • 26—controllercardcodemismatch

  • 27—controllercardtypemismatch

  • 28—controllermissing

  • 29—controlleroverheat

  • 30—controllerswitchauto

 
  • 31—controllerswitchcompleted

  • 32—controllerswitchexfailed

  • 33—controllerswitchforced

  • 34—controllerswitchmanual

  • 35—localfantrayinventfail

  • 36—localinventfail

  • 37—localbackplaneinventfail

  • 38—lostm2m

  • 39—nonvolatilememfail

  • 40—peerhwincompatible

  • 41—peerinventfail

  • 42—peermodeincompatible

  • 43—peersharedformatmismatch

  • 44—rtclockfail

  • 45—mic1missing

  • 46—mic2missing

  • 47—mic1mismatch

  • 48—mic2mismatch

  • 49—mic1voltagefailure

  • 50—mic2voltagefailure

  • 51—mic1overheat

  • 52—mic2overheat

  • 53—mic1failure

  • 54—mic2failure

  • 55—mic1podfail

  • 56—mic2podfail

  • 57—mic1diagnosticfail

  • 58—mic2diagnosticfail

  • 59—ethtransceiverrxpowerhi

  • 60—ethtransceiverrxpowerlo

 
  • 61—ethtransceivertemphi

  • 62—ethtransceivertemplo

  • 63—ethtranceivervoltagehi

  • 64—ethtranceivervoltagelo

  • 65—ethtransceiverbiashi

  • 66—ethtransceiverbiaslo

  • 67—ethtransceivertxpowerhi

  • 68—ethtransceivertxpowerlo

  • 69—ethtransceiveraux1hi

  • 70—ethtransceiveraux1lo

  • 71—ethtransceiveraux2hi

  • 72—ethtransceiveraux2lo

  • 73—ethtransceiverlvcc5hi

  • 74—ethtransceiverlvcc5lo

  • 75—ethtransceiverlvcc3hi

  • 76—ethtransceiverlvcc3lo

  • 77—ethtransceiverlvcc2hi

  • 78—ethtransceiverlvcc2lo

  • 82—aseAsp1Down

  • 83—aseAsp2Down

 

rbnCardAlarmDateAndTime


Octet String (Size (8 | 11))

rbnCardAlarmDescription


SnmpAdminString (SIZE (0..64))

rbnCardAlarmProbableCause (refer to RBN-ALARM-TC.my):

  • 1—aIS

  • 3—DegradedSignal

  • 4—FarEndReceiverFailure

  • 5—FramingError

  • 6—LossOfFrame

  • 7—LossOfPointer

  • 8—LossOfSignal

  • 9—PayloadTypeMismatch

  • 10—TransmissionError

  • 12—ExcessiveBER

  • 13—PathTraceMismatch

  • 14—Unavailable

  • 15—SignalLableMismatch

  • 17—ReceiveFailure

  • 18—TransmitFailure

  • 19—ModulationFailure

  • 20—DemodulationFailure

  • 21—LinkFailure

  • 22—ConfigurationMismatch

  • 23—ConcatenationMismatch

 

Values 27–50 are reserved for communications alarm related probable causes.


The following are used with equipment alarm:

  • 51—BackplaneFailure

  • 53—EquipmentIdDuplication

  • 54—ExternalIFDeviceProblem

  • 55—LineCardProblem

  • 56—MultiplexerProblem

  • 57—NEIdentifierDuplication

  • 58—PowerProblem

  • 59—ProcessorProblem

  • 60—ProtectionPathFailure

  • 61—ReceiverFailure

  • 62—ReplaceableUnitMissing

  • 63—ReplaceableUnitTypeMismatch

  • 64—SyncSourceMismatch

  • 65—TerminalProblem

  • 66—TimingProblem

  • 67—TransmitterFailure

  • 68—TrunkCardProblem

  • 69—ReplaceableUnitProblem

  • 70—RealTimeClockFailure

 

Values 83–100 are reserved for equipment alarm related probable causes.


The following are used with environmental alarm:

  • 101—AirCompressorFailure

  • 102—AirConditioningFailure

  • 103—AirDryerFailure

  • 104—BatteryDischarging

  • 105—BatteryFailure

  • 106—CommercialPowerFailure

  • 107—CoolingFanFailure

  • 108—EngineFailure

  • 109—FireDetectorFailure

  • 110—FuseFailure

  • 111—GeneratorFailure

  • 112—LowBatteryThreshold

  • 113—PumpFailure

  • 114—RectifierFailure

  • 115—RectifierHighVoltage

  • 116—RectifierLowVoltage

  • 117—VentilationsSystemFailure

  • 118—EnclosureDoorOpen

  • 119—ExplosiveGas

   
  • 120—Fire

  • 121—Flood

  • 122—HighHumidity

  • 123—HighTemperature

  • 124—HighWind

  • 125—IceBuildUp

  • 126—IntrusionDetection

  • 127—LowFuel

  • 128—LowHumidity

  • 129—LowCablePressure

  • 130—LowTemperature

  • 131—LowWater

  • 132—Smoke

  • 133—ToxicGas

  • 149—Customized

 

Values 137–150 are reserved for environmental alarm related probable causes.


The following are used with processing error alarm:

  • 151—StorageCapacityProblem

  • 152—MemoryMismatch

  • 153—CorruptData

  • 154—OutOfCPUCycles

  • 155—SfwrEnvironmentProblem

  • 156—SfwrDownloadFailure

  • 157—LossOfRealTime

  • 158—Reinitialized

  • 159—OperationNotification

  • 160—OperationFailure

 

Values 168–200 are reserved for processing error alarm related probable causes.

  • 1001—LossOfTimingSource

  • 1002—ApsChannelProcessingFailure

  • 1003—ApsByteFailure

  • 1004—ApsChannelMatchFailure

  • 1005—ApsModeMismatch

  • 1007—LossOfTUMultiframeIndicator

  • 1010—PathSelectorFailure

  • 1011—BlsrDefaultKBytes

  • 1012—BlsrInconsistentAPSCodes

  • 1013—BlsrNodeIdMismatch

  • 1014—BlsrImproperAPSCodes

  • 1015—BlsrSquelching

  • 1016—BlsrInvalidNeighbour

  • 1017—BlsrInvalidRingMap

  • 1018—BlsrInvalidRingId

  • 1019—BlsrIncompleteRingConfig

  • 1020—BlsrIncompleteETConfig

  • 1021—BlsrNodeIncorrectOrientation

 

rbnCardAlarmSeverity:


  • 1—cleared

  • 2—critical

  • 3—major

  • 4—minor

  • 5—warning

rbnNECardAlarm


RBN-NOTIFY-ENHANCE-MIB

rbnCardAlarmServiceAffecting:


  • 1—yes

  • 2—no

rbnCardAlarmId:


  • 1—unknown

  • 2—cpFail—Circuit pack failure

  • 3—cpBackplaneFail—Circuit pack backplane failure

  • 4—diagFail—Diagnostic failure

  • 5—voltageFail—Voltage failure

  • 6—controllerSwitchFail—Controller switch failure

  • 7—controllerTempCritical—Controller temp critical

  • 8—controllerFail—Controller failure

  • 9—controllerDiagFail—Controller diag test failure

  • 10—cpPowerOnDiagFail—Circuit pack power-on—diagnostic failure

  • 11—controllerPowerOnDiagFail—Controller power-on—diagnostic failure

  • 12—cpOverheat—Circuit pack overheat

  • 13—controllerOverheat

  • 14—backplaneclkfail

  • 15—btciferror

  • 16—btcnotready

  • 17—cpbackplanedegrade

  • 18—cpcardcodemismatch

  • 19—cpmismatch

  • 20—cpmissing

  • 21—cpresetcomplete

  • 22—downloadcompleted

  • 23—downloadfailed

  • 24—syncfail

  • 25—backupfail

  • 26—controllercardcodemismatch

  • 27—controllercardtypemismatch

  • 28—controllermissing

  • 29—controlleroverheat

  • 30—controllerswitchauto

  • 31—controllerswitchcompleted

  • 32—controllerswitchexfailed

  • 33—controllerswitchforced

  • 34—controllerswitchmanual

  • 35—localfantrayinventfail

  • 36—localinventfail

  • 37—localbackplaneinventfail

  • 38—lostm2m

  • 39—nonvolatilememfail

  • 40—peerhwincompatible

  • 41—peerinventfail

  • 42—peermodeincompatible

  • 43—peersharedformatmismatch

  • 44—rtclockfail

  • 45—mic1missing

  • 46—mic2missing

  • 47—mic1mismatch

  • 48—mic2mismatch

  • 49—mic1voltagefailure

  • 50—mic2voltagefailure

  • 51—mic1overheat

  • 52—mic2overheat

  • 53—mic1failure

  • 54—mic2failure

  • 55—mic1podfail

  • 56—mic2podfail

  • 57—mic1diagnosticfail

  • 58—mic2diagnosticfail

  • 59—ethtransceiverrxpowerhi

  • 60—ethtransceiverrxpowerlo

 
  • 61—ethtransceivertemphi

  • 62—ethtransceivertemplo

  • 63—ethtranceivervoltagehi

  • 64—ethtranceivervoltagelo

  • 65—ethtransceiverbiashi

  • 66—ethtransceiverbiaslo

  • 67—ethtransceivertxpowerhi

  • 68—ethtransceivertxpowerlo

  • 69—ethtransceiveraux1hi

  • 70—ethtransceiveraux1lo

  • 71—ethtransceiveraux2hi

  • 72—ethtransceiveraux2lo

  • 73—ethtransceiverlvcc5hi

  • 74—ethtransceiverlvcc5lo

  • 75—ethtransceiverlvcc3hi

  • 76—ethtransceiverlvcc3lo

  • 77—ethtransceiverlvcc2hi

  • 78—ethtransceiverlvcc2lo

  • 82—aseAsp1Down

  • 83—aseAsp2Down

 

rbnCardAlarmType:


  • 1—other

  • 2—communicationsAlarm

  • 3—qualityOfServiceAlarm

  • 4—processingErrorAlarm

  • 5—equipmentAlarm

  • 6—environmentalAlarm

  • 7—integrityViolation

  • 8—operationalViolation

  • 9—physicalViolation

  • 10—securityServiceOrMechanismViolation

  • 11—timeDomainViolation

 

rbnCardAlarmDateAndTime


Date and time in the following format (with ranges):


  • year* (0..65536)

  • month (1..12)

  • day (1..31)

  • hour (0..23)

  • minutes (0..59)

  • seconds 0..60 (use 60 for leap-second)

  • deci-seconds (0..9)

  • direction from UTC ('+' / '-')

  • hours from UTC* (0..13)

  • minutes from UTC (0..59)


Example output: 1992-5-26,13:30:15.0,-4:0

rbnCardAlarmDescription


SnmpAdminString (SIZE(0..64))

 

rbnCardAlarmProbableCause (refer to RBN-ALARM-TC.my):

  • 1—aIS

  • 3—DegradedSignal

  • 4—FarEndReceiverFailure

  • 5—FramingError

  • 6—LossOfFrame

  • 7—LossOfPointer

  • 8—LossOfSignal

  • 9—PayloadTypeMismatch

  • 10—TransmissionError

  • 12—ExcessiveBER

  • 13—PathTraceMismatch

  • 14—Unavailable

  • 15—SignalLableMismatch

  • 17—ReceiveFailure

  • 18—TransmitFailure

  • 19—ModulationFailure

  • 20—DemodulationFailure

  • 21—LinkFailure

  • 22—ConfigurationMismatch

  • 23—ConcatenationMismatch

 

Values 27–50 are reserved for communications alarm related probable causes.


The following are used with equipment alarm:

  • 51—BackplaneFailure

  • 53—EquipmentIdDuplication

  • 54—ExternalIFDeviceProblem

  • 55—LineCardProblem

  • 56—MultiplexerProblem

  • 57—NEIdentifierDuplication

  • 58—PowerProblem

  • 59—ProcessorProblem

  • 60—ProtectionPathFailure

  • 61—ReceiverFailure

  • 62—ReplaceableUnitMissing

  • 63—ReplaceableUnitTypeMismatch

  • 64—SyncSourceMismatch

  • 65—TerminalProblem

  • 66—TimingProblem

  • 67—TransmitterFailure

  • 68—TrunkCardProblem

  • 69—ReplaceableUnitProblem

  • 70—RealTimeClockFailure

 

Values 83–100 are reserved for equipment alarm related probable causes.


The following are used with environmental alarm:

  • 101—AirCompressorFailure

  • 102—AirConditioningFailure

  • 103—AirDryerFailure

  • 104—BatteryDischarging

  • 105—BatteryFailure

  • 106—CommercialPowerFailure

  • 107—CoolingFanFailure

  • 108—EngineFailure

  • 109—FireDetectorFailure

  • 110—FuseFailure

  • 111—GeneratorFailure

  • 112—LowBatteryThreshold

  • 113—PumpFailure

  • 114—RectifierFailure

  • 115—RectifierHighVoltage

  • 116—RectifierLowVoltage

  • 117—VentilationsSystemFailure

  • 118—EnclosureDoorOpen

  • 119—ExplosiveGas

  • 120—Fire

   
  • 121—Flood

  • 122—HighHumidity

  • 123—HighTemperature

  • 124—HighWind

  • 125—IceBuildUp

  • 126—IntrusionDetection

  • 127—LowFuel

  • 128—LowHumidity

  • 129—LowCablePressure

  • 130—LowTemperature

  • 131—LowWater

  • 132—Smoke

  • 133—ToxicGas

  • 149—Customized

 

Values 137–150 are reserved for environmental alarm related probable causes.


The following are used with processing error alarm:

  • 151—StorageCapacityProblem

  • 152—MemoryMismatch

  • 153—CorruptData

  • 154—OutOfCPUCycles

  • 155—SfwrEnvironmentProblem

  • 156—SfwrDownloadFailure

  • 157—LossOfRealTime

  • 158—Reinitialized

  • 159—OperationNotification

  • 160—OperationFailure

 

Values 168–200 are reserved for processing error alarm related probable causes.

  • 1001—LossOfTimingSource

  • 1002—ApsChannelProcessingFailure

  • 1003—ApsByteFailure

  • 1004—ApsChannelMatchFailure

  • 1005—ApsModeMismatch

  • 1007—LossOfTUMultiframeIndicator

  • 1010—PathSelectorFailure

  • 1011—BlsrDefaultKBytes

  • 1012—BlsrInconsistentAPSCodes

  • 1013—BlsrNodeIdMismatch

  • 1014—BlsrImproperAPSCodes

  • 1015—BlsrSquelching

  • 1016—BlsrInvalidNeighbour

  • 1017—BlsrInvalidRingMap

  • 1018—BlsrInvalidRingId

  • 1019—BlsrIncompleteRingConfig

  • 1020—BlsrIncompleteETConfig

  • 1021—BlsrNodeIncorrectOrientation

 

rbnCardAlarmSeverity:


  • 1—cleared

  • 2—critical

  • 3—major

  • 4—minor

  • 5—warning

 

rbnNECardName


DisplayString (SIZE (0..255))

sysName


DisplayString (SIZE (0..255))

rbnSfpAlarm


RBN-SFP-MIB

rbnSfpAlarmCardSlot


Unsigned32

rbnSfpAlarmPort


Unsigned32

rbnAlarmId:


  • 59—ethtransceiverrxpowerhi

  • 60—ethtransceiverrxpowerlo

  • 61—ethtransceivertemphi

  • 62—ethtransceivertemplo

  • 63—ethtranceivervoltagehi

  • 64—ethtranceivervoltagelo

  • 65—ethtransceiverbiashi

  • 66—ethtransceiverbiaslo

  • 67—ethtransceivertxpowerhi

  • 68—ethtransceivertxpowerlo

  • 69—ethtransceiveraux1hi

  • 70—ethtransceiveraux1lo

  • 71—ethtransceiveraux2hi

  • 72—ethtransceiveraux2lo

  • 73— ethtransceiverlvcc5hi

  • 74—ethtransceiverlvcc5lo

  • 75—ethtransceiverlvcc3hi

  • 76—ethtransceiverlvcc3lo

  • 77—ethtransceiverlvcc2hi

  • 78—ethtransceiverlvcc2lo

 

rbnSfpAlarmSeverity


Integer


  • 1—cleared

  • 2—indeterminate

  • 3—critical

  • 4—major

  • 5—minor

  • 6—warning

 

rbnSfpAlarmType


Integer


5—equipmentAlarm

rbnSfpAlarmDateAndTime


OctetString

rbnSfpAlarmDescription


OctetString (0..64)

rbnSfpAlarmProbableCause (continued) 80—tranceiverFailure


Integer

6   Environmental Notifications

The following sections provide information about environmental notifications for the SmartEdge router.

6.1   Descriptions and Object Identifiers

Table 9 lists notifications generated by the router to indicate environmental notifications as defined in the RBN-ENVMON-MIB and the RBN-SYS-RESOURCES-MIB.

Table 9    Environmental Notifications

Event and OID

Description and Cause

Recommended Action

Reporting Module

Severity

Related Events and Commands

rbnFanStatusChange


1.3.6.1.4.1.2352.2.4.0.3


RBN-ENVMON-MIB

The system raises or clears this notification when the fan status changes. This notification is enabled by default.


Cause: The status of a fan test point, with the following values:


  • normal—the fan or fans monitored by the test point are operational.

  • failed—the fan or fans monitored by the test point have failed.

  • absent—the fan or fans monitored by this test point is not present.

  • unknown—the test point are unable to monitor the fan or fans.

If a fan has failed, replace the fan tray.

Node

Minor

Event: None


Command: None

rbnPowerStatusChange


1.3.6.1.4.1.2352.2.4.0.4


RBN-ENVMON-MIB

The system raises or clears this event when there is a change in power supply status.


Cause: The status of a power test point, with the following values:


  • normal—the power supply (or supplies) monitored by the test point is operational.

  • failed— the power supply (or supplies) monitored by the test point has failed.

  • absent—the power supply (or supplies) monitored by this test point is not present.

  • unknown— the test point is unable to monitor the power supply (or supplies).

Ensure that the power is correctly connected, clean, and within specifications.

Node

Major

Event: None


Command: None

rbnSRPowerExceededEvent


1.3.6.1.4.1.2352.2.24.0.4


RBN-SYS-RESOURCES-MIB

The system raises or clears this notification when a controller card is inserted and more power is drawn than recommended.


The circuits over the administratively down traffic card are impacted.


Cause: Power consumption on a SmartEdge router is over the recommended value when a controller card is inserted.

Remove a controller card or traffic card to clear the power exceed condition. Network design should avoid this scenario on a SmartEdge router

Node

Major

Event: None


Command: None

Table 10 describes the objects for environmental notifications.

Table 10    Environmental Objects

Notification

Objects and Values

rbnFanStatusChange


RBN-ENVMON-MIB

rbnFanStatus:


  • 1—normal

  • 2—failed

  • 3—absent

  • 4—unknown

rbnPowerStatusChange


RBN-ENVMON-MIB

rbnPowerStatus:


  • 1—normal

  • 2—failed

  • 3—absent

  • 4—unknown

rbnSRPowerExceededEvent


RBN-SYS-RESOURCES-MIB

rbnSRPowerExceededStatus:


  • 1—normal

  • 2—failed

6.1.1   rbnFanStatusChange Example

If a fan fails in the system, an SNMP management station might display the following output:

*TRAP_v2c{AgIpAddr=155.53.0.21
SysUpTime=23128610
SnmpTrapOID=rbnFanStatusChange
MgrSvrErrStat=NO_ERROR
}VARLIST{rbnFanStatusTable{INDEX=1
rbnFanStatus{TYPE=enum
NAM=failed
NUM=2
}}}%

7   IP Pool Notifications

Table 11 lists notifications generated by the router to indicate IP pool. The notifications are defined in RBN-IP-POOL-MIB.

Table 11    IP Pool Notifications

Event and OID

Description and Cause

Recommended Action

Reporting Module

Severity

Related Events and Commands

rbnIpPoolThreshholdMet


1.3.6.1.4.1.2352.2.15.0.2


RBN-IPPOOL-MIB

The system raises this event when the falling threshold of each pool in a context is reached.


Cause: The number of available IP addresses for the pool has decreased to the defined threshold.

This is an informative message; there are still more available IP addresses available unless you receive the rbnIpPoolContextThresholdMet alarm. If this is a named IP pool, verify that subscribers that use that named pool can still obtain IP addresses.

Context IP pool

Critical

Event: None


Command: None

rbnIpPoolContextThreshholdMet


1.3.6.1.4.1.2352.2.15.0.3


RBN-IPPOOL-MIB

The system raises this event when the falling threshold of the per-context IP pool is reached.


Cause: The number of available IP addresses for the context has decreased to the defined threshold.

Check for any connectivity issues that can prevent user authentication on the system.

Context

Critical

Event: None


Command: None

rbnIPPoolContextThreshholdPercentageMet


1.3.6.1.4.1.2352.2.15.0.1


RBN-IPPOOL-MIB

The system raises this event when the falling threshold of the per-context percentage is reached.


The percent (%) of available addresses for the context has decreased to the defined threshold.

Check for any connectivity issues that can prevent user authentication on the system.

Context

Major

Event: None


Command: None

rbnInetIpPoolHiFallingThrshMet


1.3.6.1.4.1.2352.2.15.0.4


RBN-IPPOOL-MIB

The system raises this event when the falling threshold high-water mark of per-pool address usage is reached. The number or percent of available prefixes for the pool has decreased to the defined threshold.

Check for any connectivity issues that can prevent user authentication on the system.

Context IP pool

Major

Event: None


Command: show ipv6 pool

rbnInetIpPoolLoFallingThrshMet


1.3.6.1.4.1.2352.2.15.0.5


RBN-IPPOOL-MIB

The system raises this event when the falling threshold low-water mark of per-pool address usage is reached. The number or percent of available prefixes for the pool has decreased to the defined threshold.

Check for any connectivity issues that can prevent user authentication on the system.

Context IP pool

Critical

Event: None


Command: show ipv6 pool

rbnInetIpPoolCtxHiFallingThrshMet


1.3.6.1.4.1.2352.2.15.0.6


RBN-IPPOOL-MIB

The system raises this event when the falling threshold high-water mark of per-context address usage is reached. The number or percent of available prefixes for the pool has decreased to the defined threshold.

Check for any connectivity issues that can prevent user authentication on the system.

Context

Major

Event: None


Command: show ipv6 pool

rbnInetIpPoolCtxLoFallingThrshMet


1.3.6.1.4.1.2352.2.15.0.7


RBN-IPPOOL-MIB

The system raises this event when the falling threshold low-water mark of per-pool address usage is reached. The number or percent of available prefixes for the pool has decreased to the defined threshold.

Check for any connectivity issues that can prevent user authentication on the system.

Context

Critical

Event: None


Command: show ipv6 pool

Table 12 describes the objects for IP pool notifications.

Table 12    IP Pool Objects

Notification

Objects and Values

rbnIpPoolThreshholdMet


RBN-IPPOOL-MIB

rbnIpPoolContextName


SnmpAdminString (SIZE (0..63))

rbnIpPoolInterfaceName


SnmpAdminString (SIZE (0..127))

rbnIpPoolMask


IpAddress

rbnIpPoolAvailable


Unsigned32

rbnIpPoolThreshold


Unsigned32 (0..65535)

rbnIpPoolContextThreshholdMet


RBN-IPPOOL-MIB

rbnIpPoolContextName


SnmpAdminString (SIZE (0..63))

rbnIpPoolContextAvailable


Unsigned32

rbnIpPoolContextThreshold


Unsigned32

rbnIPPoolContextThreshholdPercentageMet


RBN-IPPOOL-MIB

rbnIpPoolContextName


SnmpAdminString (SIZE (0..63))

rbnIpPoolContextTotalSize


Unsigned32

rbnIpPoolContextAvailable


Unsigned32

rbnIpPoolContextThresholdPercentage


Integer32 (0..100)

rbnInetIpPoolHiFallingThrshMet


RBN-IPPOOL-MIB

rbnInetIpPoolEndPrefixType


InetAddressType (2—IPv6)

rbnInetIpPoolEndPrefix


InetAddress (16 bytes)

rbnInetIpPoolEndPrefixLen


InetAddressLength (1..128)

rbnInetIpPoolInterfaceName


SnmpAdminString

rbnInetIpPoolName


SnmpAdminString

rbnInetIpPoolSize


Unsigned32

rbnInetIpPoolAvailable


Unsigned32

rbnInetIpPoolThrshType


RbnInetIpPoolThresholdType


  • 0—no setting

  • 1—absolute

  • 2—percentage

rbnInetIpPoolHiFallingThrsh


RbnInetIpPoolThreshold (0 to IP pool size)

rbnInetIpPoolLoFallingThrshMet


RBN-IPPOOL-MIB

rbnInetIpPoolEndPrefixType


InetAddressType (2—IPv6)

rbnInetIpPoolEndPrefix


InetAddress (16 bytes)

rbnInetIpPoolEndPrefixLen


InetAddressLength (1..128)

rbnInetIpPoolInterfaceName


SnmpAdminString

rbnInetIpPoolName


SnmpAdminString

rbnInetIpPoolSize


Unsigned32

rbnInetIpPoolAvailable


Unsigned32

rbnInetIpPoolThrshType


RbnInetIpPoolThresholdType


  • 0—no setting

  • 1—absolute

  • 2—percentage

rbnInetIpPoolLoFallingThrsh


RbnInetIpPoolThreshold (0 to IP pool size)

rbnInetIpPoolCtxHiFallingThrshMet


RBN-IPPOOL-MIB

rbnInetIpPoolCtxName


SnmpAdminString

rbnInetIpPoolCtxPoolSize


Unsigned32

rbnInetIpPoolCtxAvailable


Unsigned32

rbnInetIpPoolCtxThrshType


RbnInetIpPoolThresholdType


  • 0—no setting

  • 1—absolute

  • 2—percentage

rbnInetIpPoolCtxHiFallingThrsh


Unsigned32 (0 to IP pool size)

rbnInetIpPoolCtxLoFallingThrshMet


RBN-IPPOOL-MIB

rbnInetIpPoolCtxName


SnmpAdminString

rbnInetIpPoolCtxPoolSize


Unsigned32

rbnInetIpPoolCtxAvailable


Unsigned32

rbnInetIpPoolCtxThrshType


RbnInetIpPoolThresholdType


  • 0—no setting

  • 1—absolute

  • 2—percentage

rbnInetIpPoolCtxLoFallingThrsh


Unsigned32 (0 to IP pool size)

8   L2TP Notifications

Table 13 lists notifications generated by the router to indicate L2TP notifications as defined in the RBN-L2TP-MIB.

Table 13    L2TP Notifications

Event and OID

Description and Cause

Recommended Action

Reporting Module

Severity

Related Events and Commands

rbnL2tpMibTunnelStateChange2


1.3.6.1.4.1.2352.2.28.0.2


RBN-L2TP-MIB

The system raises or clears this event when the SNMP entity detects that the operational state of a tunnel has entered or moved from the established state. The value of the rbnL2tpMibTunnelState object determines the current tunnel state.


Cause: The tunnel may have been created (raised) or torn down (cleared).

Ensure that the correct tunnel configuration appears and that IP and link connectivity is available and free of errors between the two peers.

Context


L2TP Tunnel

Minor

Event: None


Command: None

Table 14 describes the objects for L2TP notifications.

Table 14    L2TP Objects

Notification

Objects and Values

rbnL2tpMibTunnelStateChange2


RBN-L2TP-MIB

rbnL2tpTCfgTunnelContext


SnmpAdminString (SIZE (0..80))

rbnL2tpMibTunnelState:


  • 0—Invalid

  • 1—Deleted

  • 2—Idle

  • 3—Created

  • 4—WaitAAA

  • 5—WaitCtlReply

  • 6—WaitCtlConn

  • 7—Established

rbnL2tpTCfgRemoteTunnelID


Unsigned32 (0..65535)

rbnL2tpMIBDisableTrap


TruthValue

9   L2VPN Cross-Connection (XC) Notifications

Table 15 lists notifications generated by the router to indicate L2VPN cross-connection (XC) notifications as defined in the RBN-L2VPN-MIB.

Table 15    L2VPN XC Notifications

Event and OID

Description and Cause

Recommended Action

Reporting Module

Severity

Related Events and Commands

rbnMplsL2VpnLdpPwStateChange


1.3.6.1.4.1.2352.2.39.0.1


RBN-L2VPN-MIB

This notification is generated when the XC state transitions operationally to up, down, or standby.

N/A.

Context

informational

Event: None


Command: show xc l2vpn detail

Table 16 describes the objects for L2VPN XC notifications.

Table 16    L2VPN XC Objects

Notification

Objects and Values

rbnMplsL2VpnLdpPwStateChange


RBN-L2VPN-MIB

rbnMplsL2VpnLdpPwStateChange


Integer:


  • 1—up

  • 2— down

  • 3—standby

10   Link and Interface Notifications

The following sections provide information about link and interface notifications for the SmartEdge router.

10.1   Descriptions and Object Identifiers

Table 17 lists notifications generated by the router to Indicate Link and Interface Notifications as described in the RBN-NOTIFY-ENHANCE-MIB and RFC 2863,The Interfaces Group MIB, and RFC 2495, Definitions of Managed Objects for the DS1, E1, DS2, and E2 Interface Types and RBN-ATM-PVC-OAM-MIB.

Table 17    Link and Interface Notifications

Event and OID

Description and Cause

Recommended Action

Reporting Module

Severity

Related Events and Commands

linkDown


1.3.6.1.6.3.1.1.5.3


IF-MIB

The system raises this notification when the link status of an interface is down.


Causes include:


  • A fiber is cut.

  • There is attenuation in the signal.

  • There is no frame structure in the signal transmitted by the upstream station.

  • The receiving end of the local station is faulty.

Check:


  • That the port is configured correctly.

  • That the no shutdown command is configured.

  • That the cables are plugged in properly.

  • If a link is down on the neighboring device.

  • If the port comes up when plugged into another working device.

  • System diagnostics for failed hardware.

Port, Circuit, or Interface

Critical

Event: linkUp


Command: None

rbnNElinkDown


1.3.6.1.4.1.2352.2.36.0.3


RBN-NOTIFY-ENHANCE-MIB

The system raises this notification when the link status of an interface is down.


This is an enhanced version of the linkDown trap defined in the IF-MIB. Use the traps nemib {exclusive | non-exclusive} and snmp server commands to enable this notification.


Causes include:


  • A fiber is cut.

  • There is attenuation in the signal.

  • There is no frame structure in the signal transmitted by the upstream station.

  • The receiving end of the local station is faulty.

Check:


  • That the port is configured correctly.

  • That the no shutdown command is configured.

  • That the cables are plugged in properly.

  • If a link is down on the neighboring device.

  • If the port comes up when plugged into another working device.

  • System diagnostics for failed hardware.

Port, Circuit, or Interface

Major

Event: rbnNElinkUp


Command: traps nemib {exclusive | non-exclusive}

linkUp


1.3.6.1.6.3.1.1.5.4


IF-MIB

The system clears this event when an interface link status is up.


Causes include:


  • The no shutdown command was configured on the port.

  • A cable was plugged in.

  • A port bounce occurred.

  • The system came back online.

None; this is an informative message.

Port, Circuit, or Interface

Minor

Event: LinkDown


Command: None

rbnNElinkUp


1.3.6.1.4.1.2352.2.36.0.4


RBN-NOTIFY-ENHANCE-MIB

The system clears this event when an interface link status is up.


This is an enhanced version of the linkUp trap defined in the IF-MIB. Use the traps nemib {exclusive | non-exclusive} or the snmp server commands to enable this notification.


Causes include:


  • The no shutdown command was configured on the port.

  • A cable was plugged in.

  • A port bounce occurred.

  • The system came back online.

None; this is an informative message.

Port, Circuit, or Interface

Minor

Event: rbnNElinkDown


Command: traps nemib {exclusive | non-exclusive}

dsx1LineStatusChange


1.3.6.1.2.1.10.18.15.0.1


DS1-MIB

The system raises or clears this event when the interface line status changes.


Causes include:


  • The configuration was added or modified for the circuit.

  • The circuit bounced.

Check the circuit and port counters for increased errors that can explain the cause of the bounce.

Node

Minor

Event: None


Command: None

rbnNEdsx1LineStatusChange


1.3.6.1.4.1.2352.2.36.0.5


RBN-NOTIFY-ENHANCE-MIB

The system raises or clears this event when the interface line status changes.


This is an enhanced version of the dsx1LineStatusChange trap defined in the DS1-MIB. Use the traps nemib {exclusive | non-exclusive} command to enable this notification.


Causes include:


  • The configuration was added or modified for the circuit.

  • The circuit bounced.

Check the circuit and port counters for increased errors that can explain the cause of the bounce.

Port

Minor

Event: None


Command: traps nemib {exclusive | non-exclusive}

dsx3LineStatusChange


1.3.6.1.2.1.10.30.15.0.1


DS3-MIB

The system raises or clears this event when the interface line status changes.


Causes include:


  • The configuration was added or modified for the circuit.

  • The circuit bounced.

Check the circuit and port counters for any increased errors that might explain the cause of the bounce.

Node

Minor

Event: None


Command: None

rbnNEdsx3LineStatusChange


1.3.6.1.4.1.2352.2.36.0.6


RBN-NOTIFY-ENHANCE-MIB

The system raises or clears this event when the interface line status changes.


This is an enhanced version of the dsx3LineStatusChange trap defined in the DS3-MIB. Use the traps nemib {exclusive | non-exclusive} command to enable this notification.


Causes include:


  • The configuration was added or modified for the circuit.

  • The circuit bounced.

Check the circuit and port counters for any increased errors that might explain the cause of the bounce.

Port

Minor

Event: None


Command: traps nemib {exclusive | non-exclusive}

rbnAtmPvcOamStatusStateChange


1.3.6.1.4.1.2352.2.19.0.1


RBN-ATM-PVC-OAM-MIB

The system raises or clears this event when the value changes. The notification raises when the rbnAtmPvcOamStatusState object transitions from oamUp to oamDown and clears when it transitions from any of the oamDown to oamUp.


Cause: The status of an ATM PVC changed due to an ATM PVC OAM function.

Check circuit counters for errors on PVCs. If errors increase, identify the source of the errors and check the configuration and hardware diagnostics for correct operation.

Node

Major

Events: None


Command: None

Table 18 describes the objects for link and interface notifications.

Table 18    Link and Interface Objects

Notification

Objects and Values

linkDown


IF-MIB


RFC 2863, The Interfaces Group MIB

ifIndex


Integer32 (1..2147483647)

ifAdminStatus:


  • 1—up—Ready to pass packets

  • 2—down

  • 3—testing—In test mode

ifOperStatus:


  • 1—up—Ready to pass packets

  • 2—down

  • 3—testing—In test mode

  • 4—unknown—Status can not be determined

  • 5—dormant

  • 6—notPresent—Component is missing

  • 7—lowerLayerDown—Down due to lower-layer interface state

rbnNElinkDown


RBN-NOTIFY-ENHANCE-MIB

ifIndex


Integer32 (1..2147483647)

ifAdminStatus:


  • 1—up—Ready to pass packets

  • 2—down

  • 3—testing—In test mode

ifOperStatus:


  • 1—up—Ready to pass packets

  • 2—down

  • 3—testing—In test mode

  • 4—unknown—Status cannot be determined

  • 5—dormant

  • 6—notPresent—Component is missing

  • 7—lowerLayerDown—Down due to lower-layer interface state

ifSpeed


Gauge32

ifHighSpeed


Gauge32

rbnNECircuitId


DisplayString (SIZE (0..255))

sysName


DisplayString (SIZE (0–255))

linkUp


IF-MIB

See RFC 2863, The Interfaces Group MIB


ifIndex


Integer32 (1..2147483647)

ifAdminStatus:


  • 1—up—Ready to pass packets

  • 2—down

  • 3—testing—In test mode

ifOperStatus:


  • 1—up—Ready to pass packets

  • 2—down

  • 3—testing—In test mode

  • 4—unknown—Status can not be determined

  • 5—dormant

  • 6—notPresent—Component is missing

  • 7—lowerLayerDown—Down due to state of lower-layer interfaces

rbnNElinkUp


RBN-NOTIFY-ENHANCE-MIB

ifIndex


Integer32 (1..2147483647)

ifAdminStatus:


  • 1—up—Ready to pass packets

  • 2—down

  • 3—testing—In test mode

ifOperStatus:


  • 1—up—Ready to pass packets

  • 2—down

  • 3—testing—In test mode

  • 4—unknown—Status can not be determined

  • 5—dormant

  • 6—notPresent—Component is missing

  • 7—lowerLayerDown—Down due to state of lower-layer interfaces

ifSpeed


Gauge32

ifHighSpeed


Gauge32

rbnNECircuitId


DisplayString (SIZE (0..255))

sysName


DisplayString (SIZE (0..255))

dsx1LineStatusChange


DS1-MIB

RFC 2495, Definitions of Managed Objects for the DS1, E1, DS2, and E2 Interface Types


dsx1LineStatus—The various bit positions are:


  • 1—dsx1NoAlarm
    No alarm present

  • 2—dsx1RcvFarEndLOF
    Far-end LOF (Yellow Alarm)

  • 4—dsx1XmtFarEndLOF
    Near end sending LOF Indication

  • 8—dsx1RcvAIS
    Far end sending AIS

  • 16—dsx1XmtAIS
    Near end sending AIS

  • 32—dsx1LossOfFrame
    Near-end LOF (Red Alarm)

  • 64—dsx1LossOfSignal
    Near-end loss of signal

  • 128—dsx1LoopbackState
    Near end is looped

  • 256—dsx1T16AIS
    E1 TS16 AIS

  • 512—dsx1RcvFarEndLOMF
    Far end sending TS16 LOMF

  • 1024—dsx1XmtFarEndLOMF
    Near end sending TS16 LOMF

  • 2048—dsx1RcvTestCode
    Near end detects a test code

  • 4096—dsx1OtherFailure
    Any line status not defined here

  • 8192—dsx1UnavailSigState
    Near end in unavailable signal state

  • 16384—dsx1NetEquipOOS
    Carrier equipment out of service

  • 32768—dsx1RcvPayloadAIS
    DS2 payload AIS

  • 65536—dsx1Ds2PerfThreshold
    DS2 performance threshold exceeded

 

dsx1LineStatusLastChange


TimeStamp

rbnNEdsx1LineStatusChange


dsx1LineStatus—The various bit positions are:


RBN-NOTIFY-ENHANCE-MIB

  • 1—dsx1NoAlarm
    No alarm present

  • 2—dsx1RcvFarEndLOF
    Far-end LOF (Yellow Alarm)

  • 4—dsx1XmtFarEndLOF
    Near end sending LOF Indication

  • 8—dsx1RcvAIS
    Far end sending AIS

  • 16—dsx1XmtAIS
    Near end sending AIS

  • 32—dsx1LossOfFrame
    Near-end LOF (Red Alarm)

  • 64—dsx1LossOfSignal
    Near-end loss Of signal

  • 128—dsx1LoopbackState
    Near end is looped

  • 256—dsx1T16AIS
    E1 TS16 AIS

  • 512—dsx1RcvFarEndLOMF
    Far end sending TS16 LOMF

  • 1024—dsx1XmtFarEndLOMF
    Near end sending TS16 LOMF

  • 2048—dsx1RcvTestCode
    Near end detects a test code

  • 4096—dsx1OtherFailure
    any line status not defined here

  • 8192—dsx1UnavailSigState
    Near end in unavailable signal state

  • 16384—dsx1NetEquipOOS
    Carrier equipment out of service

  • 32768—dsx1RcvPayloadAIS
    DS2 payload AIS

  • 65536—dsx1Ds2PerfThreshold
    DS2 performance threshold exceeded

 

dsx1LineStatusLastChange


TimeStamp

 

rbnDsx1AlarmSeverity:


  • cleared

  • critical

  • major

  • minor

  • warning

rbnDsx1AlarmServiceAffecting:


  • yes

  • no

rbnNECircuitId


DisplayString (SIZE (0..255))

sysName


DisplayString (SIZE (0..255))

dsx3LineStatusChange


DS3-MIB

RFC 2496, Definitions of Managed Objects for the DS3/E3 Interface Type


dsx3LineStatus—The various bit positions are:


  • 1—dsx1NoAlarm
    No alarm present

  • 2—dsx1RcvFarEndLOF
    Receiving Yellow or Remote Alarm Indication

  • 4—dsx3XmitRAIAlarm
    Transmitting Yellow or Remote Alarm Indication

  • 8—dsx3RcvAIS
    Receiving AIS failure state

  • 16—dsx3XmitAIS
    Transmitting AIS

  • 32—dsx3LOF
    Receiving LOF failure state

  • 64—dsx3LOS
    Receiving LOS failure state

  • 128—dsx3LoopbackState
    Looping the received signal

  • 256—dsx3RcvTestCode
    Receiving a test pattern

  • 512—dsx3OtherFailure
    any line status not defined here

  • 1024—dsx3UnavailSigState
    Near end in unavailable signal state

  • 2048—dsx3NetEquipOOS
    Carrier equipment out of service

dsx3LineStatusLastChange


TimeStamp

rbnNEdsx3LineStatusChange


RBN-NOTIFY-ENHANCE-MIB

dsx3LineStatus—The various bit positions are:


  • 1—dsx3NoAlarm
    No alarm present

  • 2—dsx3RcvRAIFailure
    Receiving Yellow or Remote Alarm Indication

  • 4—dsx3XmitRAIAlarm
    Transmitting Yellow or Remote Alarm Indication

  • 8—dsx3RcvAIS
    Receiving AIS failure state

  • 16—dsx3XmitAIS
    Transmitting AIS

  • 32—dsx3LOF
    Receiving LOF failure state

  • 64—dsx3LOS
    Receiving LOS failure state

  • 128—dsx3LoopbackState
    Looping the received signal

  • 256—dsx3RcvTestCode
    Receiving a test pattern

  • 512—dsx3OtherFailure
    any line status not defined here

  • 1024—dsx3UnavailSigState
    Near End in unavailable signal state

  • 2048—dsx3NetEquipOOS
    Carrier equipment out of service

 

dsx3LineStatusLastChange


TimeStamp

rbnDsx3AlarmSeverity:


  • 1—cleared

  • 2—critical

  • 3—major

  • 4—minor

  • 5—warning

 

rbnDsx3AlarmServiceAffecting:


  • 1—yes

  • 2—no

rbnNECircuitId


DisplayString (SIZE (0..255))

sysName


DisplayString (SIZE (0..255))

rbnAtmPvcOamStatusStateChange


RBN-ATM-PVC-OAM-MIB

rbnAtmPvcOamStatusState:


  • 1—noOam

  • 2—oamUp—The ATM PVC OAM function is active, and no failure condition is detected on the circuit.

  • 3—oamDownLoopback—The ATM PVC OAM function is active, and F5 OAM loopback cell management has detected a fault on the circuit.

  • 4—oamDownAis—The ATM PVC OAM function is active, and the system received a VC-AIS cell, which indicates a fault on the circuit.

  • 5—oamDownRdi—The ATM PVC OAM function is active, and the system received a VC-RDI cell, which indicates a fault on the circuit.

10.1.1   rbnNElinkUp Example

If Port 12/8 in SmartEdge-Lab1 system becomes operational, the CLI displays the following output:

2008-05-06 16:06:14 SE-Lab1 [10.192.16.214]:
SNMPv2-MIB::sysUpTime.0 = Timeticks: (285745234) 33 days, 1:44:12.34
SNMPv2-MIB::snmpTrapOID.0 = OID: SNMPv2-SMI::enterprises.2352.2.36.0.4
IF-MIB::ifIndex.13 = INTEGER: 13
IF-MIB::ifAdminStatus.13 = INTEGER: up(1) 
IF-MIB::ifOperStatus.13 = INTEGER: up(1)
IF-MIB::ifSpeed.13 = Gauge32: 100000000 
IF-MIB::ifHighSpeed.13 = Gauge32: 100
SNMPv2-SMI::enterprises.2352.2.36.1.1.4.0 = STRING: "12-8"
SNMPv2-MIB::sysName.0 = STRING: SE-Lab1

10.1.2   rbnNElinkDown Example

If Port 5/2 in SmartEdge-Lab1 system becomes operational, the CLI might display the following output:

2008-05-06 16:05:53 SE-Lab1 [10.192.16.214]:
SNMPv2-MIB::sysUpTime.0 = Timeticks: (285743090) 33 days, 1:43:50.90
SNMPv2-MIB::snmpTrapOID.0 = OID: SNMPv2-SMI::enterprises.2352.2.36.0.3
IF-MIB::ifIndex.13 = INTEGER: 13
IF-MIB::ifAdminStatus.13 = INTEGER: up(1)
IF-MIB::ifOperStatus.13 = INTEGER: up(1)
IF-MIB::ifSpeed.13 = Gauge32: 10000000 
IF-MIB::ifHighSpeed.13 = Gauge32: 10
SNMPv2-SMI::enterprises.2352.2.36.1.1.4.0 = STRING: "12-8"
SNMPv2-MIB::sysName.0 = STRING: SE-Lab1

11   Media Gateway Notifications

Table 19 lists notifications generated by the router to monitor Media Gateway status.

Table 19    Media Gateway Notifications

Event and OID

Description and Cause

Recommended Action

Reporting Module

Severity

Related Events and Commands

rbnH248LinkStatusAlarm


1.3.6.1.4.1.2352.2.52.0.1

The H.248 link for a Media Gateway Controller (MGC) Group was down for more than the configured timeout with major severity (rbnMGEventSeverity).


Contains the following objects:


  • rbnMGEventDateAndTime

  • rbnMGEventSeverity

  • rbnMGEventSender

  • rbnMGEventType

  • rbnMGEventProbableCause

  • rbnMGEventInformation


The notification is sent with a rbnMGEventSeverity value of clear when the link state is restored to the Up state or is obsoleted due to a configuration change.

See rbnMGEventProbableCause

Node

See rbnMGEventSeverity

Configure the timeout value with the alarms h248-link-status command in global configuration mode; the default is 30 seconds.

12   RMON Notifications

Table 20 lists notifications generated by the router to indicate RMON notifications as defined in RFC 2819, Remote Network Monitoring Management Information Base.

Table 20    RMON Notifications

Event and OID

Description and Cause

Recommended Action

Reporting Module

Severity

Related Events and Commands

fallingAlarm


1.3.6.1.2.1.16.0.2


RMON-MIB

The system clears this notification when remote monitoring (RMON) falls.


Cause: The value of a MIB object decreases. For example, you can monitor whether the temperature of the router decreases.

Dependent upon which MIB object you set up for this notification to monitor.

Node

Warning

Events: risingAlarm


Commands: None.

risingAlarm


1.3.6.1.2.1.16.0.1


RMON-MIB

The system raises this notification when remote monitoring (RMON) rises.


Cause: The value of a MIB object increases. For example, you can monitor an error counter to determine if errors increase.

Dependent upon which MIB object you set up for this notification to monitor.

Node

Warning

Events: fallingAlarm


Commands: None.

Table 21 describes the objects for RMON notifications.

Table 21    RMON Objects

Notification

Objects and Values

fallingAlarm


RMON-MIB

See RFC 2819, Remote Network Monitoring Management Information Base


alarmIndex

alarmVariable


Object Identifier

alarmSampleType:


  • 1—absoluteValue

  • 2—deltaValue

alarmValue


Integer32

alarmRisingThreshold


Integer32

risingAlarm


RMON-MIB

See RFC 2819, Remote Network Monitoring Management Information Base


alarmIndex


Integer32

alarmVariable


Object Identifier

alarmSampleType:


  • 1—absoluteValue

  • 2—deltaValue

alarmValue


Integer32

alarmRisingThreshold


Integer32

13   Routing Notifications

The following sections provide information about routing notifications for the SmartEdge router.

13.1   Descriptions and Object Identifiers

Table 22 lists notifications generated by the router to indicate routing notifications as defined in RFC 4273, Definitions of Managed Objects for BGP-4 and RFC 4750, OSPF Version 2 MIB.

Table 22    Routing Notifications

Event and OID

Description and Cause

Recommended Action

Reporting Module

Severity

Related Events and Commands

bgpBackwardTransNotification


1.3.6.1.2.1.15.0.2


BGP4-MIB

The system raises this event when BGP FSM moves from a higher-numbered state to a lower-numbered state.


Possible causes:


  • Port flapping

  • Other problem establishing a BGP neighbor.

Ensure that BGP is correctly configured and that there are no errors in IP and link connectivity between neighboring devices.

BGP

Minor

Event: bgpEstablishedNotification


Command: None

bgpEstablished Notification


1.3.6.1.2.1.15.0.1


BGP4-MIB

The system clears this event when BGP FSM enters the established state.


Cause: Neighbor relationship between BGP peers is established.

None; this is for information only.

BGP

Minor

Event: bgpBackwardTransNotification


Command: None

mplsL3VpnVrfUp


1.3.6.1.2.1.10.166.11.0 .1


MPLS-L3VPN-STD-MIB

This system raises this event when:


  • No interface is associated with this Virtual Routing and Forwarding (VRF) and the ifOperStatus of the first following interface changed to up (1).

  • One interface is associated with this VRF and the ifOperStatus of the interface changed to up (1).

  • Multiple interfaces are associated with this VRF, the ifOperStatus of all interfaces is down (2), except the first, which changed to up (1).

Ensure that the correct number of interfaces are associated with the VRF and that the operational status is correct.

Node

Informational

Event: linkUp, linkDown, mplsL3vpnvrfUp, mplsL3VpnVrfDown


Commands: show ip interface; show bindings

mplsL3VpnVrfDown


1.3.6.1.2.1.10.166.11.0.2


MPLS-L3VPN-STD-MIB

The system raises this event when:


  • One interface is associated with this VRF and the ifOperStatus of the interface changed from up (1) to down (2)

  • Multiple interfaces are associated with this VRF and the ifOperStatus of all interfaces is equal to up (1), except one, which changes from up (1) to down (2).

  • The last interface with ifOperStatus equal to up (1) is disassociated from a VRF

Ensure that the correct number of interfaces are associated with the VRF and that the operational status is correct.

Node

Informational

Event: linkUp, linkDown, mplsL3vpnvrfUp, mplsL3VpnVrfDown


Commands: show ip interface; show bindings

mplsL3VpnVrfRouteMidThreshExceeded


1.3.6.1.2.1.10.166.11.0.3


MPLS-L3VPN-STD-MIB

This notification is generated when the number of routes contained by the specified VRF exceeds the value indicated by mplsL3VpnVrfMidRouteThreshold.

A single notification MUST be generated when this threshold is exceeded, and no other notifications of this type should be issued until the value f mplsL3VpnVrfPerfCurrNumRoutes has fallen below that of mplsL3VpnVrfConfMidRteThresh.

Node

Informational

Event: None.


Commands: snmp server traps mplsl3vpn; ip | ipv6 maximum-routes vpn.

mplsL3VpnVrfNumVrfRouteMaxThreshExceeded


1.3.6.1.2.1.10.166.11.0.4


MPLS-L3VPN-STD-MIB

This notification is generated when the number of routes contained by the specified VRF exceeds or attempts to exceed the maximum allowed value as indicated by mplsL3VpnVrfMaxRouteThreshold. In cases where mplsL3VpnVrfConfHighRteThresh is set to the same value as mplsL3VpnVrfConfMaxRoutes, mplsL3VpnVrfConfHighRteThresh need not be exceeded; rather, just reached for this notification to be issued.


The default value is 0 minutes.

If this value is set to 0, the agent should only issue a single notification at the time that the maximum threshold has been reached, and should not issue any more notifications until the value of routes has fallen below the configured threshold value.

Node

Informational

Event: None.


Commands: snmp server traps mplsl3vpn; ip | ipv6 maximum-routes vpn.

mplsL3VpnNumVrfRouteMaxThreshCleared


1.3.6.1.2.1.10.166.11.0.6


MPLS-L3VPN-STD-MIB

This notification is generated only after the number of routes contained by the specified VRF exceeds or attempts to exceed the maximum allowed value as indicated by mplsVrfMaxRouteThreshold, and then falls below this value. The emission of this notification informs the operator that the error condition has been cleared without the operator having to query the device.

A single notification will be issued to indicate the first instance of the error condition as well as the first time the error condition is cleared.

Node

Informational

Event: None.


Commands: snmp server traps mplsl3vpn; ip | ipv6 maximum-routes vpn.

ospfIfStateChange


1.3.6.1.2.1.14.16.2.1


OSPF-MIB

The system raises this trap when a change in the state of a nonvirtual OSPF interface occurs.


Cause: This trap is generated when the interface state regresses (for example when it transitions DR to Down) or progresses to one of the following terminal states:


  • Point-to-Point

  • DR Other

  • DR

  • Backup

If the transition is to a lower state, for example the down state, determine whether the state transition was expected or represents a problem in your OSPF network.

OSPF

Informational

Event: None


Command: show ospf interface

ospfVirtIfStateChange


1.3.6.1.2.1.14.16.2.1


OSPF-MIB

The system raises this event when the state of an OSPF virtual interface changes.


Cause: The interface state changes from Point-to-Point to Down or to a terminal state (for example, Point-to-Point state).

If the transition is to a lower state, for example the down state, determine whether the state transition was expected or represents a problem in your OSPF network.

OSPF

Informational

Event: None


Command: show ospf interface

ospfNbrStateChange


1.3.6.1.2.1.14.16.2.2


OSPF-MIB

The system raises this notification when there has been a change in the state of a nonvirtual OSPF neighbor.


Cause: The neighbor state regresses (for example, changes from the attempt state or full state to one way or down state) or progresses to a terminal state (for example to a two-way state or full state). When a neighbor transitions from or to the full state on non-broadcast multi-access and broadcast networks, the trap should be generated by the designated router. A designated router transitioning to Down will be noted by ospfIfStateChange.

If the transition is to a lower state, for example the down state, determine whether the state transition was expected or represents a problem in your OSPF network.

OSPF

Informational

Event: None


Command: show ospf neighbor

ospfVirtNbrStateChange


1.3.6.1.2.1.14.16.2.3


OSPF-MIB

The system raises this notification when the state of an OSPF virtual neighbor changes.


Cause: The system generates this notification when the neighbor state regresses (for example, from the attempt or full state to the one-way or down state) or progresses to a terminal state (for example, the full state).

If the transition is to a lower state, for example the down state, determine whether the state transition was expected or represents a problem in your OSPF network.

OSPF

Informational

Event: None


Command: show ospf neighbor

ospfIfConfigError


1.3.6.1.2.1.14.16.2.4


OSPF-MIB

The system raises this notification when a nonvirtual interface receives a packet from a router with configuration parameters that conflict with the receiving router's configuration parameters.(1)

Confirm that the configuration of the sending and receiving router is correct.

OSPF

Informational

Event: None


Command: show ospf interface detail; show ospf malform

ospfVirtIfConfigError


1.3.6.1.2.1.14.16.2.5


OSPF-MIB

The system raises this notification when a virtual interface receives a packet from a router with configuration parameters that conflict with the receiving router's configuration parameters.(2)

Confirm that the configuration of the sending and receiving router is correct.

OSPF

Informational

Event: None


Command: show ospf interface detail; show ospf malform

ospfIfAuthFailure


1.3.6.1.2.1.14.16.2.6


OSPF-MIB

The system raises this notification when a nonvirtual interface receives a packet from a router with a authentication key or authentication type that conflicts with the authentication key or authentication type of the receiving router.

Confirm that the authentication key and authentication type of the sending and receiving router are correct.

OSPF

Informational

Event: None


Command: show ospf interface detail; show ospf malform

ospfVirtIfAuthFailure


1.3.6.1.2.1.14.16.2.7


OSPF-MIB

The system raises this notification when a non virtual interface receives a packet from a router with a authentication key or authentication type that conflicts with the authentication key or authentication type of the receiving router.

Confirm that the authentication key and authentication type of the sending and receiving router are correct.

OSPF

Informational

Event: None


Command: show ospf interface detail; show ospf malform

ospfIfRxBadPacket


1.3.6.1.2.1.14.16.2.8


OSPF-MIB

The system raises this event when a virtual interface receives an OSPF packet that cannot be parsed.

Determine whether the packet received in error is expected or represents a problem in your OSPF network.

OSPF

Informational

Event: None


Command: show ospf malform

ospfVirtIfRxBadPacket


1.3.6.1.2.1.14.16.2.9


OSPF-MIB

The system raises this event when a nonvirtual interface receives an OSPF packet that cannot be parsed.

Determine whether the packet received in error is expected or represents a problem in your OSPF network.

OSPF

Informational

Event: None


Command: show ospf malform

ospfTxRetransmit


1.3.6.1.2.1.14.16.2.10


OSPF-MIB

The system raises this event when a nonvirtual interface retransmits an OSPF packet. All packets that may be retransmitted are associated with an LSDB entry.

Use the LS type, LS ID, and router ID to identify the LSDB entry.

OSPF

Informational

Event: None


Command: show ospf database

ospfVirtIfTxRetransmit


1.3.6.1.2.1.14.16.2.11


OSPF-MIB

The system raises this event when a virtual interface retransmits an OSPF packet. All packets that may be retransmitted are associated with an LSDB entry.

Use the LS type, LS ID, and Router ID to identify the LSDB entry.

OSPF

Informational

Event: None


Command: show ospf database

ospfOriginateLsa


1.3.6.1.2.1.14.16.2.12


OSPF-MIB

The system raises this trap when the router originates a new LSA.


Cause: An LSA is originated or resent due to a topology change.

Determine whether the change to Link State Advertisement (LSA) was expected or represents a problem in your OSPF network.

OSPF

Informational

Event: None


Command: show ospf database

ospfMaxAgeLsa


1.3.6.1.2.1.14.16.2.13


OSPF-MIB

The system raises this event when one of the LSAs in the router’s link database has aged to the maximum age (3,600 seconds) as identified in the object MaxAge.

Determine whether the Link State Advertisement (LSA) withdrawal was expected or represents a problem in your OSPF network.

OSPF

Informational

Event: None


Command: show ospf database

vrrpTrapNewMaster


1.3.6.1.2.1.68.0.1


VRRP-MIB

The sending agent has transitioned to the Master state.


This trap is disabled by default. Enable this trap in the CLI by using the snmp server traps vrrpmib command or setting the vrrpNotificationCntl SNMP object.

N/A

SNMP

Informational

Event: vNone


Command: show vrrp statistics

vrrpTrapAuthFailure


1.3.6.1.2.1.68.0.2


VRRP-MIB

The authentication key or authentication type of an incoming packet conflicts with the authentication key or authentication type of the specified VRRP router.


This trap is disabled by default and has to be enabled in CLI or through MIB by using the snmp server traps vrrpmib command or setting the vrrpNotificationCntl SNMP object.

Determine whether the backup VRRP router uses the same authentication type and key as the Master VRRP. Correct the authentication type and key if needed.

SNMP

Informational

Event: vrrpTrapNewMaster


Command: show vrrp statistics

(1)  the optionMismatch event causes a trap only if it prevents an adjacency from forming.

(2)  the optionMismatch event causes a trap only if it prevents an adjacency from forming.


Table 23 describes the objects for routing notifications.

Table 23    Routing Objects

Notification

Objects and Values

bgpBackwardTransNotification


BGP4-MIB

See RFC 4273, Definitions of Managed Objects for BGP-4


bgpPeerRemoteAddr


IpAddress

bgpPeerLastError


Error code and subcode seen by the peer


Octet String (Size (2))

bgpPeerState:


  • 1—idle

  • 2—connect

  • 3—active

  • 4—opensent

  • 5—openconfirm

  • 6—established

bgpEstablished Notification


BGP4-MIB

See RFC 4273, Definitions of Managed Objects for BGP-4


bgpPeerRemoteAddr


IpAddress

bgpPeerLastError


Error code and subcode seen by the peer


Octet String (Size (2))

bgpPeerState:


  • 1—idle

  • 2—connect

  • 3—active

  • 4—opensent

  • 5—openconfirm

  • 6—established

mplsL3VpnVrfUp


MPLS-L3VPN-STD-MIB

mplsL3VpnIfConfRowStatus


  • 1—active

  • 2—notInService

  • 3—notReady

  • 4—createAndGo

  • 5—createAndWait

  • 6—destroy

mplsL3VpnVrfOperStatus


  • 1—up

  • 2—down

mplsL3VpnVrfDown


MPLS-L3VPN-STD-MIB

mplsL3VpnIfConfRowStatus


  • 1—active

  • 2—notInService

  • 3—notReady

  • 4—createAndGo

  • 5—createAndWait

  • 6—destroy

mplsL3VpnVrfOperStatus


  • 1—up

  • 2—down

mplsL3VpnVrfRouteMidThreshExceeded


MPLS-L3VPN-STD-MIB

mplsL3VpnVrfPerfCurrNumRoutes


Gauge32


Integer (0..4294967295)

mplsL3VpnVrfConfMidRteThresh


Unsigned32


Integer (0..4294967295)

mplsL3VpnVrfNumVrfRouteMaxThreshExceeded


MPLS-L3VPN-STD-MIB

mplsL3VpnVrfPerfCurrNumRoutes


Gauge32


Integer (0..4294967295)

mplsL3VpnVrfConfHighRteThresh


Unsigned32


Integer (0..4294967295)

mplsL3VpnNumVrfRouteMaxThreshCleared


MPLS-L3VPN-STD-MIB

mplsL3VpnVrfPerfCurrNumRoutes


Gauge32


Integer (0..4294967295)

mplsL3VpnVrfConfHighRteThresh


Unsigned32


Integer (0..4294967295)

ospfIfStateChange


OSPF-MIB

See RFC 4750,


OSPF Version 2 MIB


ospfRouterId—The originator of the trap

ospfIfIpAddress


IpAddress

ospfAddressLessIf


Integer32 (0..2147483647)

ospfIfState:


  • 1—down

  • 2—loopback

  • 3—waiting

  • 4—pointToPoint

  • 5—designatedRouter

  • 6—backupDesignatedRouter

  • 7—otherDesignatedRouter

ospfNbrStateChange


OSPF-MIB

See RFC 4750, OSPF Version 2 MIB


ospfRouterId


IpAddress

ospfNbrIpAddr


IpAddress

ospfNbrAddressLessIndex


Integer32 (0..2147483647)

ospfNbrRtrId


IpAddress

ospfNbrState:


  • 1—down

  • 2—attempt

  • 3—init

  • 4—twoWay

  • 5—exchangeStart

  • 6—exchange

  • 7—loading

  • 8—full

ospfVirtIfStateChange


OSPF-MIB

ospfRouterId


IpAddress

ospfVirtIfAreaId


IpAddress

ospfVirtIfNeighbor


IpAddress

ospfVirtIfState:


  • 1—down

  • 4—pointToPoint

ospfVirtNbrStateChange


OSPF-MIB

ospfRouterId


IpAddress

ospfVirtNbrArea


IpAddress

ospfVirtNbrRtrId


IpAddress

ospfVirtNbrState


Integer:


  • 1—down

  • 2—attempt

  • 3—init

  • 4—twoWay

  • 5—exchangeStart

  • 6—exchange

  • 7—loading

  • 8—full

ospfIfConfigError


OSPF-MIB

ospfRouterId


IpAddress

ospfIfIpAddress


IpAddress

ospfAddressLessIf


InterfaceIndexOrZero

ospfPacketSrc


IpAddress

ospfConfigErrorType


Integer:


  • 1—badVersion

  • 2—areaMismatch

  • 3—unknownNbmaNbr

  • 4—unknownVirtualNbr

  • 7—netMaskMismatch

  • 8—helloIntervalMismatch

  • 9—deadIntervalMismatch

  • 10—optionMismatch

  • 11—mtuMismatch

  • 12—duplicateRouterId

  • 13—noError

ospfPacketType


Integer:


  • 1—hello

  • 2—dbDescript

  • 3—lsReq

  • 4—lsUpdate

  • 5—lsAck

  • 6—nullPacket

ospfVirtIfConfigError


OSPF-MIB

ospfRouterId


IpAddress

ospfVirtIfAreaId


IpAddress

ospfVirtIfNeighbor


IpAddress

ospfConfigErrorType


Integer:


  • 1—badVersion

  • 2—areaMismatch

  • 3—unknownNbmaNbr

  • 4—unknownVirtualNbr

  • 7—netMaskMismatch

  • 8—helloIntervalMismatch

  • 9—deadIntervalMismatch

  • 10—optionMismatch

  • 11—mtuMismatch

  • 12—duplicateRouterId

  • 13—noError

ospfPacketType


Integer:


  • 1—hello

  • 2—dbDescript

  • 3—lsReq

  • 4—lsUpdate

  • 5—lsAck

  • 6—nullPacket

ospfIfAuthFailure


OSPF-MIB

ospfRouterId


IpAddress

ospfAddressLessIf


InterfaceIndexOrZero

ospfPacketSrc


IpAddress

ospfConfigErrorType


Integer:


  • 5—authTypeMismatch

  • 6—authFailure

ospfPacketType


Integer:


  • 1—hello

  • 2—dbDescript

  • 3—lsReq

  • 4—lsUpdate

  • 5—lsAck

  • 6—nullPacket

ospfVirtIfAuthFailure


OSPF-MIB

ospfRouterId


IpAddress

ospfVirtIfAreaId


IpAddress

ospfVirtIfNeighbor


IpAddress

ospfConfigErrorType


Integer:


  • 5—authTypeMismatch

  • 6—authFailure

ospfPacketType


Integer:


  • 1—hello

  • 2—dbDescript

  • 3—lsReq

  • 4—lsUpdate

  • 5—lsAck

  • 6—nullPacket

ospfIfRxBadPacket


OSPF-MIB

ospfRouterId


IpAddress

ospfIfIpAddress


IpAddress

ospfAddressLessIf


InterfaceIndexOrZero

ospfPacketSrc


IpAddress

ospfPacketType


Integer:


  • 1—hello

  • 2—dbDescript

  • 3—lsReq

  • 4—lsUpdate

  • 5—lsAck

  • 6—nullPacket

ospfVirtIfRxBadPacket


OSPF-MIB

ospfRouterId


IpAddress

ospfVirtIfAreaId


IpAddress

ospfVirtIfNeighbor


IpAddress

ospfPacketType


Integer:


  • 1—hello

  • 2—dbDescript

  • 3—lsReq

  • 4—lsUpdate

  • 5—lsAck

  • 6—nullPacket

ospfTxRetransmit


OSPF-MIB

ospfRouterId


IpAddress

ospfIfIpAddress


IpAddress

ospfAddressLessIf


InterfaceIndexOrZero

ospfNbrRtrId


IpAddress

ospfPacketType


Integer:


  • 2—dbDescript

  • 3—lsReq

  • 4—lsUpdate

ospfLsdbType


Integer:


  • 1—routerLink

  • 2—networkLink

  • 3—summaryLink

  • 4—asSummaryLink

  • 5—asExternalLink

  • 6—multicastLink

  • 7—nssaExternalLink

  • 10—areaOpaqueLink

ospfLsdbLsid


IpAddress

ospfLsdbRouterId


IpAddress

ospfVirtIfTxRetransmit


OSPF-MIB

ospfRouterId


IpAddress

ospfVirtIfAreaId


IpAddress

ospfVirtIfNeighbor


IpAddress

ospfPacketType


Integer:


  • 2—dbDescript

  • 3—lsReq

  • 4—lsUpdate

ospfLsdbType


Integer:


  • 1—routerLink

  • 2—networkLink

  • 3—summaryLink

  • 4—asSummaryLink

  • 5—asExternalLink

  • 6—multicastLink

  • 7—nssaExternalLink

  • 10—areaOpaqueLink

ospfLsdbLsid


IpAddress

ospfLsdbRouterId


IpAddress

ospfOriginateLsa


OSPF-MIB

ospfRouterId


IpAddress

ospfLsdbAreaId


IpAddress

ospfLsdbType


Integer:


  • 1—routerLink

  • 2—networkLink

  • 3—summaryLink

  • 4—asSummaryLink

  • 5—asExternalLink

  • 6—multicastLink

  • 7—nssaExternalLink

  • 10—areaOpaqueLink

ospfLsdbLsid


IpAddress

ospfLsdbRouterId


IpAddress

ospfMaxAgeLsa


OSPF-MIB

ospfRouterId


IpAddress

ospfLsdbAreaId


IpAddress

ospfLsdbType


Integer:


  • 1—routerLink

  • 2—networkLink

  • 3—summaryLink

  • 4—asSummaryLink

  • 5—asExternalLink

  • 6—multicastLink

  • 7—nssaExternalLink

  • 10—areaOpaqueLink

ospfLsdbLsid


IpAddress

ospfLsdbRouterId


IpAddress

vrrpTrapNewMaster


VRRP-MIB

vrrpOperMasterIpAddr


IpAddress

vrrpTrapAuthFailure


VRRP-MIB

vrrpTrapPacketSrc


IpAddress

vrrpTrapAuthErrorType


Integer:


  • 1—invalidAuthType

  • 2—authTypeMismatch

  • 3—authFailure

13.1.1   ospfNbrStateChange Example

If the OSPF neighbor state changes to the initial state for neighbor router 2.2.2.2, the CLI output displays:

From: 10.12.129.18
sysUpTime.0 = 00:15:58.54
snmpTrapOID.0 = ospfNbrStateChange
ospfRouterId.2.2.2.2.0 = 22.22.22.22
ospfNbrIpAddr.2.2.2.2.0 = 2.2.2.2
ospfNbrAddressLessIndex.2.2.2.2.0 = 0
ospfNbrRtrId.2.2.2.2.0 = 11.11.11.11
ospfNbrState.2.2.2.2.0 = exchangeStart(5)

13.1.2   vrrpTrapNewMaster Example

If the VRRP state transitions to Master for router 2.2.2.2, the CLI output displays:

From: 2.2.2.2
sysUpTime.0 = 01:34:47.59
snmpTrapOID.0 = vrrpTrapNewMaster
vrrpOperMasterIpAddr.67108865.3 = 10.1.1.1

13.1.3   Enable Notifications for VRRP-MIB Example

To enable notifications for VRRP-MIB by using the CLI, enter the following commands:

[local]jazz#config
[local]jazz(config)#snmp server
[local]jazz(config-snmp-server)#traps vrrpmib

To enable the VRRP-MIB notifications by using your SNMP management tool, set the vrrpNotificationCntl object to 1: enabled. To disable VRRP-MIB notifications by using the SNMP management tool, set the vrrpNotificationCntl object to 2: disabled.

13.1.4   vrrpTrapAuthFailure Example

If the authentication key or authentication type of an inbound VRRP packet from VRRP router 1.1.1.10 conflicts with the authentication key or authentication type of VRRP router 2.2.2.2, the CLI displays the following output:

From: 2.2.2.2
sysUpTime.0 = 01:15:37.98
snmpTrapOID.0 = vrrpTrapAuthFailure
vrrpTrapPacketSrc = 1.1.1.10
vrrpTrapAuthErrorType = authFailure(3)

14   System Management Notifications

Table 24 lists notifications generated by the router to indicate system management notifications as defined in RFC 3418, Management Information Base (MIB) for the Simple Network Management Protocol (SNMP).

Table 24    System Management Notifications

Event and OID

Description and Cause

Recommended Action

Reporting Module

Severity

Related Events and Commands

authenticationFailure


1.3.6.1.6.3.1.1.5.5


SNMPv2-MIB

The system raises this event when it could not authenticate the address of a protocol message.


Cause: A device attempted to connect by using the incorrect community string.

Use access lists to only allow SNMP connections from trusted sources. Verify that the SNMP community string uses the correct configuration.

SNMP agent

Warning

Event: none.


Command: none.

coldStart


1.3.6.1.6.3.1.1.5.1


SNMPv2-MIB

The system raises this event when the SNMP agent restarts.


Cause: One of the following can cause SNMP to restart:


  • Process restart

  • XCRP switchover

  • Chassis reload

Determine whether the SNMP process restarted or if the XCRP performed a switchover. Send the output from the show tech and show crashfiles commands to customer support.

SNMP agent

Critical

Event: none.


Command: none.

pingProbeFailed


1.3.6.1.2.1.80.0.1


PING-MIB

Generated when a probe failure is detected, when the corresponding pingCtlTrapGeneration object is set to probeFailure(0), subject to the value of pingCtlTrapProbeFailureFilter. The object pingCtlTrapProbeFailureFilter can be used to specify the number of consecutive probe failures that are required before this notification can be generated.

Walk pingProbeHistoryTable to get details.

Node

Informational

Event: none


Command: none.

pingTestFailed


1.3.6.1.2.1.80.0.2


PING-MIB

The system raises this event when a ping test fails.


Cause: The corresponding pingCtlTrapGeneration object is set to testFailure(1). The pingCtlTrapTestFailureFilter object specifies the number of probes in a test that must fail in order to consider the test failed.

Walk pingProbeHistoryTable to get details.

Node

Informational

Event: none


Command: none.

pingTestCompleted


1.3.6.1.2.1.80.0.3


PING-MIB

Generated when a ping test completes.


Cause: The corresponding pingCtlTrapGeneration object is set to testCompletion(2).

None.

Node

Informational

Event: none.


Command: show snmp ping, snmp ping.

traceRoutePathChange


1.3.6.1.2.1.81.0.1


TRACEROUTE-MIB

Generated when the path to a target has changed.

None.

Node

Informational

Event: none. Command: show snmp traceroute, snmp traceroute.

traceRouteTestFailed


1.3.6.1.2.1.81.0.2


TRACEROUTE-MIB

Generated when the path to a target could not be determined.

None.

Node

Informational

Event: none. Command: show snmp traceroute, snmp traceroute.

traceRouteTestCompleted


1.3.6.1.2.1.81.0.3


TRACEROUTE-MIB

Generated when the path to a target is determined.

None.

Node

Informational

Event: none. Command: show snmp traceroute, snmp traceroute.

dot1agCfmFaultAlarm


1.3.111.2.802.1.1.8.0.1


IEEE8021-CFM-MIB

The system raises this alarm when a maintenance association endpoint (MEP) has a persistent defect condition.


Cause: The MEP has a persistent defect condition.

After you receive the notification, identify the system from the network source address of the notification. Identify the MEP reporting the defect from the indices in the OID of the dot1agCfmMepHighestPrDefect variable in the notification.


The dot1agCfmMdIndex in the OID identifies the maintenance domain in which in the MEP exists.


The value of the dot1agCfmMaIndex object identifies the MEP's maintenance association


The value of the dot1agCfmMepIdentifier object identifies the CFM database MEPID of the MEP reporting this defect.


Only 1 local MEP is allowed per maintenance association in a working condition.


A defect to A raised trap is caused by a remote MEP. The local MEP reporting the defect is present in the identifier along with the highest defect for the MEP. The remote MEP id is not in the trap content and the remote MEP causing the error can be found only from the show logs.


The defect condition is the value of the dot1agCfmMepHighestPrDefect variable and is raised by the MEP whenever it loses or restores contact with one or more other MEPs.

CFM

Warning

Event: none


Command: none

rbnBulkStatsTrfrFail2


1.3.6.1.4.1.2352.2.21.0.2


RBN-BULKSTATS-MIB

The system raises this when bulkstats data does not transfer to the receiver


Cause: The SmartEdge router could not reach the server for the bulkstats transfer.

Verify that IP and link connectivity are up for the SmartEdge router and server. Verify that the protocol in use (for example, FTP) is not being blocked and that those services are correctly configured on the SmartEdge router and server.

Node

Major

Event: none


Command: none.

Table 25 describes the objects for system management notifications.

Table 25    System Management Notification Objects

Notification

Objects and Values

authenticationFailure


SNMPv2-MIB

See RFC 3418, Management Information Base (MIB) for the Simple Network Management Protocol (SNMP)

coldStart


SNMPv2-MIB

See RFC 3418, Management Information Base (MIB) for the Simple Network Management Protocol (SNMP)

dot1agCfmFaultAlarm


IEEE8021-CFM-MIB

dot1agCfmMepHighestPrDefect


Dot1agCfmHighestDefectPri


  • 0—none

  • 1—defRDICCM

  • 2—defMACstatus

  • 3—defRemoteCCM

  • 4—defErrorCCM

  • 5—defXconCCM

pingProbeFailed


PING-MIB

pingCtlTargetAddressType


InetAddressType


Default is 0.


  • 0—unknown

  • 1—ipv4

  • 16—dns

 

pingCtlTargetAddress


InetAddress


Octet String (Size (0..255))

 

pingResultsOperStatus


Integer:


  • 1—enabled

  • 2—disabled

  • 3—completed

 

pingResultsIpTargetAddressType


InetAddressType


Default is 0.


  • 0—unknown

  • 1—ipv4

 

pingResultsIpTargetAddress


InetAddress


Octet String (Size (0..255))

pingResultsMinRtt


Unsigned32


Integer (0..4294967295)

pingResultsMaxRtt


Unsigned32


Integer (0..4294967295)

pingResultsAverageRtt


Unsigned32


Integer (0..4294967295)

pingResultsProbeResponses


Gauge32


Integer (0..4294967295)

pingResultsSentProbes


Gauge32


Integer (0..4294967295)

pingResultsRttSumOfSquares


Unsigned32


Integer (0..4294967295)

pingResultsLastGoodProbe


DateAndTime


Octet String (SIZE (11))

pingTestFailed


PING-MIB

pingCtlTargetAddressType


InetAddressType


Default is 0.


  • 0—unknown

  • 1—ipv4

  • 16—dns

 

pingCtlTargetAddress


InetAddress


Octet String (Size (0..255))

 

pingResultsOperStatus:


3—completed

 

pingResultsIpTargetAddressType


InetAddressType


Default is 0.


  • 0—unknown

  • 1—ipv4

 

pingResultsIpTargetAddress


InetAddress


Octet String (Size (0..255))

pingResultsMinRtt


Unsigned32


Implicit Integer (0..4294967295)

pingResultsMaxRtt


Unsigned32


Implicit Integer (0..4294967295)

pingResultsAverageRtt


Unsigned32


Implicit Integer (0..4294967295)

pingResultsProbeResponses


Gauge32


Implicit Integer (0..4294967295)

pingResultsSentProbes


Gauge32


Implicit Integer (0..4294967295)

pingResultsRttSumOfSquares


Unsigned32


Implicit Integer (0..4294967295)

pingResultsLastGoodProbe


DateAndTime


Octet String (SIZE (11))

pingTestCompleted


PING-MIB

pingCtlTargetAddressType


InetAddressType


Default is 0.


  • 0—unknown

  • 1—ipv4

  • 16—dns

 

pingCtlTargetAddress


InetAddress


Octet String (Size (0..255))

 

pingResultsOperStatus


3—completed

 

pingResultsIpTargetAddressType


InetAddressType


Default is 0.


  • 0—unknown

  • 1—ipv4

 

pingResultsIpTargetAddress


InetAddress


Octet String (Size (0..255))

 

pingResultsMinRtt


Unsigned32


Implicit Integer (0..4294967295)

pingResultsMaxRtt


Unsigned32


Implicit Integer (0..4294967295)

pingResultsAverageRtt


Unsigned32


Implicit Integer (0..4294967295)

pingResultsProbeResponses


Gauge32


Implicit Integer (0..4294967295)

pingResultsSentProbes


Gauge32


Implicit Integer (0..4294967295)

pingResultsRttSumOfSquares


Unsigned32


Implicit Integer (0..4294967295)

pingResultsLastGoodProbe


DateAndTime


Octet String (SIZE (11))

traceRoutePathChange


TRACEROUTE-MIB

traceRouteCtlTargetAddressType


InetAddressType


  • 0—unknown

  • 1—ipv4

  • 16—dns

traceRouteCtlTargetAddress


InetAddress


Octet String (Size (0..255))

traceRouteResultsIpTgtAddrType


InetAddressType


  • 0—unknown

  • 1—ipv4

  • 16—dns

traceRouteResultsIpTgtAddr


InetAddress


Octet String (Size (0..255))

traceRouteTestFailed


TRACEROUTE-MIB

traceRouteCtlTargetAddressType


InetAddressType


  • 0—unknown

  • 1—ipv4

  • 16—dns

traceRouteCtlTargetAddress


InetAddress


Octet String (Size (0..255))

traceRouteResultsIpTgtAddrType


InetAddressType


  • 0—unknown

  • 1—ipv4

traceRouteResultsIpTgtAddr


InetAddress


Octet String (Size (0..255))

traceRouteTestCompleted


TRACEROUTE-MIB

traceRouteCtlTargetAddressType


InetAddressType


  • 0—unknown

  • 1—ipv4

  • 16—dns

traceRouteCtlTargetAddress


InetAddress


Octet String (Size (0..255))

traceRouteResultsIpTgtAddrType


InetAddressType


  • 0—unknown

  • 1—ipv4

traceRouteResultsIpTgtAddr


InetAddress


Octet String (Size (0..255))

rbnBulkStatsTrfrFail2


RBN-BULKSTATS-MIB

rbnBulkStatsLastTrfrIpAddrType2


InetAddressType


Integer


  • 0—unknown

  • 1—ipv4

  • 2—ipv6

  • 16—dns

rbnBulkStatsLastTrfrIpAddr2


InetAddress


Octet String (Size (0..255))

rbnBulkStatsLastTrfrStatus2


Integer:


  • 1—none

  • 2—success

  • 3—genError

  • 4—loginFailed

  • 5—badFilename

  • 6—remoteHostFailed

  • 7—other

14.1   dot1agCfmFaultAlarm Example

If you want to determine whether a maintenance association endpoint (MEP) has a persistent defect condition, an SNMP management station might display the following output for the dot1agCfmFaultAlarm notification. In this case, there is no persistent defect condition because dot1agCfmMepHighestPrDefect.1.1.0 is set to none(0), which means that no defect is present:

Community: public@local
From: 10.12.129.29
sysUpTime.0 = 04:17:04.81
snmpTrapOID.0 = dot1agCfmFaultAlarm
dot1agCfmMepHighestPrDefect.1.1.0 = none(0)

15   System Resource Notifications

Table 26 lists notifications generated by the router to indicate system resource notifications as defined in the RBN-CONFIG-MIB and the RBN-SYS-RESOURCES-MIB.

Table 26    System Resource Notifications

Event and OID

Description and Cause

Recommended Action

Reporting Module

Severity

Related Events and Commands

rbnSRProcessEvent


1.3.6.1.4.1.2352.2.24.0.1


RBN-SYS-RESOURCES-MIB

The system raises this event when a process stops and clears this event when it begins.


A process may have terminated and impact the associated services unless the process is restarted.


Cause: A process restarted.

Use the show crashfiles command to check the crash files. Use the show tech command to show the crash files to customer support for investigation.


A process may have terminated unexpectedly. Debug the system if the process does not restart automatically.

Controller

Major

Event: None


Command: None

rbnSRStorageFailedEvent


1.3.6.1.4.1.2352.2.24.0.3


RBN-SYS-RESOURCES-MIB

The system raises this event when the value of the rbnSRStorageStatus object for a device changes to failed.


Possible causes:


  • Card exceeded the supported number of times it can read and write data

  • Other hardware failure

Replace the flash card.

Controller

Warning

Event: None


Command: None

rbnSRSwitchoverEvent


1.3.6.1.4.1.2352.2.24.0.2


RBN-SYS-RESOURCES-MIB

The system raises this event when an XCRP switchover occurs.


Cause: The XCRP was manually switched over, or automatically switched over, to recover from an error.

Use the show crashfiles command to check the crash files. Use the show tech command to show the crash files to customer support for investigation.

Controller

Informational

Event: None


Command: None

rcfJobCompleted


1.3.6.1.4.1.2352.2.13.0.1


RBN-CONFIG-FILE-MIB

The system raises this event when it completes a configuration job.


Cause: The configuration has completed loading.

None; this is for information only.

Controller

Minor

Event: None


Command: None

Table 27 describes the objects for system resource notifications.

Table 27    System Resource Objects

Notification

Objects and Values

rbnSRProcessEvent


RBN-SYS-RESOURCES-MIB

rbnSRProcessNotifyPID


Unsigned32 (0..2147483647)

rbnSRProcessNotifyEventCause


Integer:


  • 1—firstStart

  • 2—hangup

  • 3—interrupt

  • 4—quit

  • 5—illegalInstruction

  • 6—traceTrap

  • 7—abort

  • 8—emt

  • 9—floatingPointException

  • 10—kill

  • 11—busError

  • 12—segmentFault

  • 13—systemCallError

  • 14—pipeError

  • 15—alarmClock

  • 16—softwareTermination

  • 17—urgentConditionOnIOChannel

  • 18—stopNotFromTty

  • 19—stopFromTty

  • 20—continueStopped

  • 21—childExit

  • 22—ttyInput

  • 23—ttyOutput

  • 24—inputOutput

  • 25—exceededCpuTime

  • 26—exceededFileSize

  • 27—virtualAlarm

  • 28—profilingAlarm

  • 29—windowResize

  • 30—infoRequest

  • 31—userDefined1

  • 32—userDefined2

  • 33—powerFailRestart

  • 34—unknown

rbnSRProcessNotifyEventType:


  • 1—death

  • 2—birth

rbnSRProcessNumOfSpawn


Unsigned32 (0..2147483647)

rbnSRStorageFailedEvent


RBN-SYS-RESOURCES-MIB

rbnSRStorageDescr


SnmpAdminString (SIZE (0..64))

rbnSRStorageMedia:


  • 1—other

  • 2—hardDisk

  • 3—flashMemory

rbnSRStorageSlot


Unsigned32 (0..255)

rbnSRSwitchoverEvent


RBN-SYS-RESOURCES-MIB

N/A

rcfJobCompleted


RBN-CONFIG-FILE-MIB

rcfJobResult:


  • 0—success

  • 1—other

  • 2—noMemory

  • 3—parse

  • 4—io

  • 5—access

rcfJobErrorMsgs


SnmpAdminString


Octet String (SIZE (0..255))

16   System Security Notifications

Table 28 lists notifications generated by the router to monitor malicious packets. For this function, the router samples data at the start and end of the interval configured using the interval command in malicious-traffic configuration mode. The difference between the start and end of the interval is called the delta value.

Table 28    System Security Notifications

Event and OID

Description and Cause

Recommended Action

Reporting Module

Severity

Related Events and Commands

rbnMaliciousPktsThresholdHi


1.3.6.1.4.1.2352.5.54.1.1.3

This high-threshold alarm is sent when the context-wide rbnMaliciousPktsCounter (aggregate drop counter) reaches or exceeds the configured high watermark within the configured interval.

None.

Node

Warning

Event: None


Command: Set the high threshold with the threshold high low command in malicious-traffic configuration mode.

rbnMaliciousPktsThresholdLow


1.3.6.1.4.1.2352.5.54.1.1.4

This low-threshold alarm is sent when the context-wide rbnMaliciousPktsCounter (aggregate drop counter) reaches or falls below the configured low watermark.

None.

Node

Warning

Event: None


Command: Set the low threshold with the threshold high low command in malicious-traffic configuration mode.

17   System Services Engine (SSE) Notifications

Table 29 lists notifications generated by the router to indicate system resource events as defined in the RBN-SSE-MIB.

Table 29    System Services Engine (SSE) Notifications

Event and OID

Description and Cause

Recommended Action

Reporting Module

Severity

Related Events and Commands

rbnSseFsgSwitchManual


1.3.6.1.4.1.2352.2.48.0.1


RBN-SSE-MIB

The system raises this event when the file server group manual switch is in progress.


Probable Cause: Operation Notification

Determine whether the manual switch was intentional.

Node

Major

Event: None


Command: None

rbnSseFsgSwitchAuto


1.3.6.1.4.1.2352.2.48.0.2


RBN-SSE-MIB

The system raises this event when the file server group automatic switch is in progress.


Probable Cause: Operation Notification

Determine whether the automatic switch was the result of an intended process.

Node

Warning

Event: None


Command: None

rbnSseFsgSwitchCompleted


1.3.6.1.4.1.2352.2.48.0.3


RBN-SSE-MIB

The system raises this event when the file server group switch completed.


Probable Cause: Operation Notification

None. Informational only.

Node

Warning

Event: None


Command: None

rbnSseFsgSwitchFail


1.3.6.1.4.1.2352.2.48.0.4


RBN-SSE-MIB

The system raises this event when the file server group switch failed.


Probable Cause: Operation Notification

Determine the cause of the failure.

Node

Major

Event: None


Command: None

rbnSseFsgSwitchWtr


1.3.6.1.4.1.2352.2.48.0.5


RBN-SSE-MIB

The system raises this event when the file server group automatic switch is waiting to be restored.


Probable Cause: Configuration or customization error

Determine if the automatic switch is waiting as a result of a stalled system or process.

Node

Warning

Event: None


Command: None

rbnSseFsgNotOperational


1.3.6.1.4.1.2352.2.48.0.6


RBN-SSE-MIB

The system raises this event when the file server group is not operational.


Probable Cause: Database Inconsistency

Determine if the file server group should be operational and, if so, what is causing the file server group to not be operational.

Node

Major

Event: None


Command: None

rbnSseFsgBlockDeviceFail


1.3.6.1.4.1.2352.2.48.0.7


RBN-SSE-MIB

The system raises this event when the file server group block device failed.


Probable Cause: Operation Failure

Determine the reason for the failure.

Node

Major

Event: None


Command: None

rbnSseFsgPartitionNotOperational


1.3.6.1.4.1.2352.2.48.0.8


RBN-SSE-MIB

The system raises this event when the file server group partition is not operational.


Probable Cause: Database inconsistency

Determine why the partition is not operational.

Node

Major

Event: None


Command: None

rbnSseFsgParitionDataSyncing


1.3.6.1.4.1.2352.2.48.0.9


RBN-SSE-MIB

The system raises this event when the file server group partition data sync is in progress.


Probable Cause: Configuration or customization error.

Determine whether the data sync is intentional.

Node

Warning

Event: None


Command: None

rbnSseFsgParitionDataSyncFail


1.3.6.1.4.1.2352.2.48.0.10


RBN-SSE-MIB

The system raises this event when the file server group partition data sync failed.


Probable Cause: Operation Failure

Determine why the partition data sync failed.

Node

Major

Event: None


Command: None

rbnSseFsgPartitionFull


1.3.6.1.4.1.2352.2.48.0.11


RBN-SSE-MIB

The system raises this event when the file server group partition is full


Probable Cause: Operation Notification

Determine why the partition is full and clean out entries or add more space to the partition.

Node

Major

Event: None


Command: None

rbnSseFsgPartitionLow


1.3.6.1.4.1.2352.2.48.0.12


RBN-SSE-MIB

The system raises this event when the file server group partition is low in space.


Probable Cause: Operation Notification

Determine why the partition is low in space and clean out entries or add more space to the partition.

Node

Warning

Event: None


Command: None

rbnSseFsgPartitionNotOperStandby


1.3.6.1.4.1.2352.2.48.0.13


RBN-SSE-MIB

The system raises this event when the file server group partition is not ready at standby


Probable Cause: Database Inconsistency

Determine why the partition is not ready at standby.

Node

Major

Event: None


Command: None

Table 30 describes the objects for system resource notifications.

Table 30    System Services Engine (SSE) Objects

Notification

Objects and Values

rbnSseFsgSwitchManual


RBN-SSE-MIB

rbnSseAlarmDateAndTime


DateAndTime

rbnSseAlarmSeverity


Integer:


  • 1—cleared

  • 2—indeterminate

  • 3—critical

  • 4—major

  • 5—minor

  • 6—warning

 

rbnSseAlarmProbableCause


Integer:


  • 1—aIS

  • 2—callSetUpFailure

  • 3—degradedSignal

  • 4—farEndReceiverFailure

  • 5—framingError

  • 6—lossOfFrame

  • 7—lossOfPointer

  • 8—lossOfSignal

  • 9—payloadTypeMismatch

  • 10—transmissionError

  • 11—remoteAlarmInterface

  • 12—excessiveBER

  • 13—pathTraceMismatch

  • 14—unavailable

  • 15—signalLabelMismatch

  • 16—lossOfMultiFrame

  • 17—receiveFailure

  • 18—transmitFailure

  • 19—modulationFailure

  • 20—demodulationFailure

  • 21—broadcastChannelFailure

  • 22—connectionEstablishmentError

  • 23—invalidMessageReceived

  • 24—localNodeTransmissionError

  • 25—remoteNodeTransmissionError

  • 26—routingFailure

  • 51—backplaneFailure

  • 52—dataSetProblem

  • 53—equipmentIdentifierDuplication

  • 54—externalIFDeviceProblem

  • 55—lineCardProblem

  • 56—multiplexerProblem

  • 57—nEIdentifierDuplication

  • 58—powerProblem

  • 59—processorProblem

  • 60—protectionPathFailure

  • 61—receiverFailure

  • 62—replaceableUnitMissing

  • 63—replaceableUnitTypeMismatch

  • 64—synchronizationSourceMismatch

  • 65—terminalProblem

  • 66—timingProblem

  • 67—transmitterFailure

  • 68—trunkCardProblem

  • 69—replaceableUnitProblem

  • 70—realTimeClockFailure

  • 71—antennaFailure

  • 72—batteryChargingFailure

  • 73—diskFailure

  • 74—frequencyHoppingFailure

  • 75—iODeviceError

  • 76—lossOfSynchronisation

  • 77—lossOfRedundancy

  • 78—powerSupplyFailure

  • 79—signalQualityEvaluationFailure

  • 80—tranceiverFailure

  • 81—protectionMechanismFailure

  • 82—protectingResourceFailure

 
  • 101—airCompressorFailure

  • 102—airConditioningFailure

  • 103—airDryerFailure

  • 104—batteryDischarging

  • 105—batteryFailure

  • 106—commercialPowerFailure

  • 107—coolingFanFailure

  • 108—engineFailure

  • 109—fireDetectorFailure

  • 110—fuseFailure

  • 111—generatorFailure

  • 112—lowBatteryThreshold

  • 113—pumpFailure

  • 114—rectifierFailure

  • 115—rectifierHighVoltage

  • 116—rectifierLowFVoltage

  • 117—ventilationsSystemFailure

  • 118—enclosureDoorOpen

  • 119—explosiveGas120—fire

  • 121—flood

  • 122—highHumidity

  • 123—highTemperature

  • 124—highWind

  • 125—iceBuildUp

  • 126—intrusionDetection

  • 127—lowFuel

  • 128—lowHumidity

  • 129—lowCablePressure

  • 130—lowTemperatue

  • 131—lowWater

  • 132—smoke

  • 133—toxicGas

  • 134—coolingSystemFailure

  • 135—externalEquipmentFailure

  • 136—externalPointFailure

  • 151—storageCapacityProblem

  • 152—memoryMismatch

  • 153—corruptData

  • 154—outOfCPUCycles

  • 155—sfwrEnvironmentProblem

  • 156—sfwrDownloadFailure

  • 157—lossOfRealTimel

  • 158—applicationSubsystemFailure

  • 159—configurationOrCustomisationError

  • 160—databaseInconsistency

 
  • 161—fileError

  • 162—outOfMemory

  • 163—softwareError

  • 164—timeoutExpired

  • 165—underlayingResourceUnavailable

  • 166—versionMismatch

  • 201—bandwidthReduced

  • 202—congestion

  • 203—excessiveErrorRate

  • 204—excessiveResponseTime

  • 205—excessiveRetransmissionRate

  • 206—reducedLoggingCapability

  • 207—systemResourcesOverload

  • 500—adapterError

  • 501—applicationSubsystemFailture

  • 502—bandwidthReducedX733

  • 503—callEstablishmentError

  • 504—communicationsProtocolError

  • 505—communicationsSubsystemFailure

  • 506—configurationOrCustomizationError

  • 507—congestionX733

  • 508—coruptData

  • 509—cpuCyclesLimitExceeded

  • 510—dataSetOrModemError

  • 511—degradedSignalX733

  • 512—dteDceInterfaceError

  • 513—enclosureDoorOpenX733

  • 514—equipmentMalfunction

  • 515—excessiveVibration

  • 516—fileErrorX733

  • 517—fireDetected

  • 518—framingErrorX733

  • 519—heatingVentCoolingSystemProblem

  • 520—humidityUnacceptable

  • 521—inputOutputDeviceError

  • 522—inputDeviceError

  • 523—lanError

  • 524—leakDetected

  • 525—localNodeTransmissionErrorX733

  • 526—lossOfFrameX733

  • 527—lossOfSignalX733

  • 528—materialSupplyExhausted

  • 529—multiplexerProblemX733

  • 530—outOfMemoryX733

 
  • 531—ouputDeviceError

  • 532—performanceDegraded

  • 533—powerProblems

  • 534—pressureUnacceptable

  • 535—processorProblems

  • 536—pumpFailureX733

  • 537—queueSizeExceeded

  • 538—receiveFailureX733

  • 539—receiverFailureX733

  • 540—remoteNodeTransmissionErrorX733

  • 541—resourceAtOrNearingCapacity

  • 542—responseTimeExecessive

  • 543—retransmissionRateExcessive

  • 544—softwareErrorX733

  • 545—softwareProgramAbnormallyTerminated

  • 546—softwareProgramError

  • 547—storageCapacityProblemX733

  • 548—temperatureUnacceptable

  • 549—thresholdCrossed

  • 550—timingProblemX733

  • 551—toxicLeakDetected

  • 552—transmitFailureX733

  • 553—transmiterFailure

  • 554—underlyingResourceUnavailable

  • 555—versionMismatchX733

  • 600—authenticationFailure

  • 601—breachOfConfidentiality

  • 602—cableTamper

  • 603—delayedInformation

  • 604—denialOfService

  • 605—duplicateInformation

  • 606—informationMissing

  • 607—informationModificationDetectede

  • 608—informationOutOfSequence

  • 609—keyExpired

  • 610—nonRepudiationFailure

  • 611—outOfHoursActivity

  • 612—outOfServic

  • 613—proceduralError

  • 614—unauthorizedAccessAttempt

  • 615—unexpectedInformation

  • 1024—other

 

rbnSseEventType


Integer:


  • 1—other

  • 2—communicationsAlarm

  • 3—qualityOfServiceAlarm

  • 4—processingErrorAlarm

  • 5—equipmentAlarm

  • 6—environmentalAlarm

  • 7—integrityViolation

  • 8—operationalViolation

  • 9—physicalViolation

  • 10—securityServiceOrMechanismViolation

  • 11—timeDomainViolation

 

rbnSseAlarmDescription


SnmpAdminString


SIZE(0..64)

 

rbnFSGroupState


Integer:


  • 0—unknown

  • 1—up

  • 2—down

  • 3—partial

  • 4—stale

  • 5— noCard

  • 6—unassigned

rbnSseFsgSwitchAuto


RBN-SSE-MIB

rbnSseAlarmDateAndTime


DateAndTime

rbnSseAlarmSeverity


Integer:


  • 1—cleared

  • 2— indeterminate

  • 3—critical

  • 4—major

  • 5—minor

  • 6—warning

 

rbnSseAlarmProbableCause


Integer:


  • 1—aIS

  • 2—callSetUpFailure

  • 3—degradedSignal

  • 4—farEndReceiverFailure

  • 5—framingError

  • 6—lossOfFrame

  • 7—lossOfPointer

  • 8—lossOfSignal

  • 9—payloadTypeMismatch

  • 10—transmissionError

  • 11—remoteAlarmInterface

  • 12—excessiveBER

  • 13—pathTraceMismatch

  • 14—unavailable

  • 15—signalLabelMismatch

  • 16—lossOfMultiFrame

  • 17—receiveFailure

  • 18—transmitFailure

  • 19—modulationFailure

  • 20—demodulationFailure

  • 21—broadcastChannelFailure

  • 22—connectionEstablishmentError

  • 23—invalidMessageReceived

  • 24—localNodeTransmissionError

  • 25—remoteNodeTransmissionError

  • 26—routingFailure

  • 51—backplaneFailure

  • 52—dataSetProblem

  • 53—equipmentIdentifierDuplication

  • 54—externalIFDeviceProblem

  • 55—lineCardProblem

  • 56—multiplexerProblem

  • 57—nEIdentifierDuplication

  • 58—powerProblem

  • 59—processorProblem

  • 60—protectionPathFailure

  • 61—receiverFailure

  • 62—replaceableUnitMissing

  • 63—replaceableUnitTypeMismatch

  • 64—synchronizationSourceMismatch

  • 65—terminalProblem

  • 66—timingProblem

  • 67—transmitterFailure

  • 68—trunkCardProblem

  • 69—replaceableUnitProblem

  • 70—realTimeClockFailure

  • 71—antennaFailure

  • 72—batteryChargingFailure

  • 73—diskFailure

  • 74—frequencyHoppingFailure

  • 75—iODeviceError

  • 76—lossOfSynchronisation

  • 77—lossOfRedundancy

  • 78—powerSupplyFailure

  • 79—signalQualityEvaluationFailure

  • 80—tranceiverFailure

  • 81—protectionMechanismFailure

  • 82—protectingResourceFailure

 
  • 101—airCompressorFailure

  • 102—airConditioningFailure

  • 103—airDryerFailure

  • 104—batteryDischarging

  • 105—batteryFailure

  • 106—commercialPowerFailure

  • 107—coolingFanFailure

  • 108—engineFailure

  • 109—fireDetectorFailure

  • 110—fuseFailure

  • 111—generatorFailure

  • 112—lowBatteryThreshold

  • 113—pumpFailure

  • 114—rectifierFailure

  • 115—rectifierHighVoltage

  • 116—rectifierLowFVoltage

  • 117—ventilationsSystemFailure

  • 118—enclosureDoorOpen

  • 119—explosiveGas120—fire

  • 121—flood

  • 122—highHumidity

  • 123—highTemperature

  • 124—highWind

  • 125—iceBuildUp

  • 126—intrusionDetection

  • 127—lowFuel

  • 128—lowHumidity

  • 129—lowCablePressure

  • 130—lowTemperatue

  • 131—lowWater

  • 132—smoke

  • 133—toxicGas

  • 134—coolingSystemFailure

  • 135—externalEquipmentFailure

  • 136—externalPointFailure

  • 151—storageCapacityProblem

  • 152—memoryMismatch

  • 153—corruptData

  • 154—outOfCPUCycles

  • 155—sfwrEnvironmentProblem

  • 156—sfwrDownloadFailure

  • 157—lossOfRealTimel

  • 158—applicationSubsystemFailure

  • 159—configurationOrCustomisationError

  • 160—databaseInconsistency

 
  • 161—fileError

  • 162—outOfMemory

  • 163—softwareError

  • 164—timeoutExpired

  • 165—underlayingResourceUnavailable

  • 166—versionMismatch

  • 201—bandwidthReduced

  • 202—congestion

  • 203—excessiveErrorRate

  • 204—excessiveResponseTime

  • 205—excessiveRetransmissionRate

  • 206—reducedLoggingCapability

  • 207—systemResourcesOverload

  • 500—adapterError

  • 501—applicationSubsystemFailture

  • 502—bandwidthReducedX733

  • 503—callEstablishmentError

  • 504—communicationsProtocolError

  • 505—communicationsSubsystemFailure

  • 506—configurationOrCustomizationError

  • 507—congestionX733

  • 508—coruptData

  • 509—cpuCyclesLimitExceeded

  • 510—dataSetOrModemError

  • 511—degradedSignalX733

  • 512—dteDceInterfaceError

  • 513—enclosureDoorOpenX733

  • 514—equipmentMalfunction

  • 515—excessiveVibration

  • 516—fileErrorX733

  • 517—fireDetected

  • 518—framingErrorX733

  • 519—heatingVentCoolingSystemProblem

  • 520—humidityUnacceptable

  • 521—inputOutputDeviceError

  • 522—inputDeviceError

  • 523—lanError

  • 524—leakDetected

  • 525—localNodeTransmissionErrorX733

  • 526—lossOfFrameX733

  • 527—lossOfSignalX733

  • 528—materialSupplyExhausted

  • 529—multiplexerProblemX733

  • 530—outOfMemoryX733

 
  • 531—ouputDeviceError

  • 532—performanceDegraded

  • 533—powerProblems

  • 534—pressureUnacceptable

  • 535—processorProblems

  • 536—pumpFailureX733

  • 537—queueSizeExceeded

  • 538—receiveFailureX733

  • 539—receiverFailureX733

  • 540—remoteNodeTransmissionErrorX733

  • 541—resourceAtOrNearingCapacity

  • 542—responseTimeExecessive

  • 543—retransmissionRateExcessive

  • 544—softwareErrorX733

  • 545—softwareProgramAbnormallyTerminated

  • 546—softwareProgramError

  • 547—storageCapacityProblemX733

  • 548—temperatureUnacceptable

  • 549—thresholdCrossed

  • 550—timingProblemX733

  • 551—toxicLeakDetected

  • 552—transmitFailureX733

  • 553—transmiterFailure

  • 554—underlyingResourceUnavailable

  • 555—versionMismatchX733

  • 600—authenticationFailure

  • 601—breachOfConfidentiality

  • 602—cableTamper

  • 603—delayedInformation

  • 604—denialOfService

  • 605—duplicateInformation

  • 606—informationMissing

  • 607—informationModificationDetectede

  • 608—informationOutOfSequence

  • 609—keyExpired

  • 610—nonRepudiationFailure

  • 611—outOfHoursActivity

  • 612—outOfServic

  • 613—proceduralError

  • 614—unauthorizedAccessAttempt

  • 615—unexpectedInformation

  • 1024—other

 

rbnSseEventType


Integer:


  • 1—other

  • 2—communicationsAlarm

  • 3—qualityOfServiceAlarm

  • 4—processingErrorAlarm

  • 5—equipmentAlarm

  • 6—environmentalAlarm

  • 7—integrityViolation

  • 8—operationalViolation

  • 9—physicalViolation

  • 10—securityServiceOrMechanismViolation

  • 11—timeDomainViolation

rbnSseAlarmDescription


SnmpAdminString


SIZE(0..64)

rbnFSGroupState


Integer:


  • 0—unknown

  • 1—up

  • 2—down

  • 3—partial

  • 4—stale

  • 5— noCard

  • 6—unassigned

rbnSseFsgSwitchCompleted


RBN-SSE-MIB

rbnSseAlarmDateAndTime


DateAndTime

rbnSseAlarmSeverity


Integer:


  • 1—cleared

  • 2— indeterminate

  • 3—critical

  • 4—major

  • 5—minor

  • 6—warning

 

rbnSseAlarmProbableCause


Integer:


  • 1—aIS

  • 2—callSetUpFailure

  • 3—degradedSignal

  • 4—farEndReceiverFailure

  • 5—framingError

  • 6—lossOfFrame

  • 7—lossOfPointer

  • 8—lossOfSignal

  • 9—payloadTypeMismatch

  • 10—transmissionError

  • 11—remoteAlarmInterface

  • 12—excessiveBER

  • 13—pathTraceMismatch

  • 14—unavailable

  • 15—signalLabelMismatch

  • 16—lossOfMultiFrame

  • 17—receiveFailure

  • 18—transmitFailure

  • 19—modulationFailure

  • 20—demodulationFailure

  • 21—broadcastChannelFailure

  • 22—connectionEstablishmentError

  • 23—invalidMessageReceived

  • 24—localNodeTransmissionError

  • 25—remoteNodeTransmissionError

  • 26—routingFailure

  • 51—backplaneFailure

  • 52—dataSetProblem

  • 53—equipmentIdentifierDuplication

  • 54—externalIFDeviceProblem

  • 55—lineCardProblem

  • 56—multiplexerProblem

  • 57—nEIdentifierDuplication

  • 58—powerProblem

  • 59—processorProblem

  • 60—protectionPathFailure

  • 61—receiverFailure

  • 62—replaceableUnitMissing

  • 63—replaceableUnitTypeMismatch

  • 64—synchronizationSourceMismatch

  • 65—terminalProblem

  • 66—timingProblem

  • 67—transmitterFailure

  • 68—trunkCardProblem

  • 69—replaceableUnitProblem

  • 70—realTimeClockFailure

  • 71—antennaFailure

  • 72—batteryChargingFailure

  • 73—diskFailure

  • 74—frequencyHoppingFailure

  • 75—iODeviceError

  • 76—lossOfSynchronisation

  • 77—lossOfRedundancy

  • 78—powerSupplyFailure

  • 79—signalQualityEvaluationFailure

  • 80—tranceiverFailure

  • 81—protectionMechanismFailure

  • 82—protectingResourceFailure

 
  • 101—airCompressorFailure

  • 102—airConditioningFailure

  • 103—airDryerFailure

  • 104—batteryDischarging

  • 105—batteryFailure

  • 106—commercialPowerFailure

  • 107—coolingFanFailure

  • 108—engineFailure

  • 109—fireDetectorFailure

  • 110—fuseFailure

  • 111—generatorFailure

  • 112—lowBatteryThreshold

  • 113—pumpFailure

  • 114—rectifierFailure

  • 115—rectifierHighVoltage

  • 116—rectifierLowFVoltage

  • 117—ventilationsSystemFailure

  • 118—enclosureDoorOpen

  • 119—explosiveGas120—fire

  • 121—flood

  • 122—highHumidity

  • 123—highTemperature

  • 124—highWind

  • 125—iceBuildUp

  • 126—intrusionDetection

  • 127—lowFuel

  • 128—lowHumidity

  • 129—lowCablePressure

  • 130—lowTemperatue

  • 131—lowWater

  • 132—smoke

  • 133—toxicGas

  • 134—coolingSystemFailure

  • 135—externalEquipmentFailure

  • 136—externalPointFailure

  • 151—storageCapacityProblem

  • 152—memoryMismatch

  • 153—corruptData

  • 154—outOfCPUCycles

  • 155—sfwrEnvironmentProblem

  • 156—sfwrDownloadFailure

  • 157—lossOfRealTimel

  • 158—applicationSubsystemFailure

  • 159—configurationOrCustomisationError

  • 160—databaseInconsistency

 
  • 161—fileError

  • 162—outOfMemory

  • 163—softwareError

  • 164—timeoutExpired

  • 165—underlayingResourceUnavailable

  • 166—versionMismatch

  • 201—bandwidthReduced

  • 202—congestion

  • 203—excessiveErrorRate

  • 204—excessiveResponseTime

  • 205—excessiveRetransmissionRate

  • 206—reducedLoggingCapability

  • 207—systemResourcesOverload

  • 500—adapterError

  • 501—applicationSubsystemFailture

  • 502—bandwidthReducedX733

  • 503—callEstablishmentError

  • 504—communicationsProtocolError

  • 505—communicationsSubsystemFailure

  • 506—configurationOrCustomizationError

  • 507—congestionX733

  • 508—coruptData

  • 509—cpuCyclesLimitExceeded

  • 510—dataSetOrModemError

  • 511—degradedSignalX733

  • 512—dteDceInterfaceError

  • 513—enclosureDoorOpenX733

  • 514—equipmentMalfunction

  • 515—excessiveVibration

  • 516—fileErrorX733

  • 517—fireDetected

  • 518—framingErrorX733

  • 519—heatingVentCoolingSystemProblem

  • 520—humidityUnacceptable

  • 521—inputOutputDeviceError

  • 522—inputDeviceError

  • 523—lanError

  • 524—leakDetected

  • 525—localNodeTransmissionErrorX733

  • 526—lossOfFrameX733

  • 527—lossOfSignalX733

  • 528—materialSupplyExhausted

  • 529—multiplexerProblemX733

  • 530—outOfMemoryX733

 
  • 531—ouputDeviceError

  • 532—performanceDegraded

  • 533—powerProblems

  • 534—pressureUnacceptable

  • 535—processorProblems

  • 536—pumpFailureX733

  • 537—queueSizeExceeded

  • 538—receiveFailureX733

  • 539—receiverFailureX733

  • 540—remoteNodeTransmissionErrorX733

  • 541—resourceAtOrNearingCapacity

  • 542—responseTimeExecessive

  • 543—retransmissionRateExcessive

  • 544—softwareErrorX733

  • 545—softwareProgramAbnormallyTerminated

  • 546—softwareProgramError

  • 547—storageCapacityProblemX733

  • 548—temperatureUnacceptable

  • 549—thresholdCrossed

  • 550—timingProblemX733

  • 551—toxicLeakDetected

  • 552—transmitFailureX733

  • 553—transmiterFailure

  • 554—underlyingResourceUnavailable

  • 555—versionMismatchX733

  • 600—authenticationFailure

  • 601—breachOfConfidentiality

  • 602—cableTamper

  • 603—delayedInformation

  • 604—denialOfService

  • 605—duplicateInformation

  • 606—informationMissing

  • 607—informationModificationDetectede

  • 608—informationOutOfSequence

  • 609—keyExpired

  • 610—nonRepudiationFailure

  • 611—outOfHoursActivity

  • 612—outOfServic

  • 613—proceduralError

  • 614—unauthorizedAccessAttempt

  • 615—unexpectedInformation

  • 1024—other

 

rbnSseEventType


Integer:


  • 1—other

  • 2—communicationsAlarm

  • 3—qualityOfServiceAlarm

  • 4—processingErrorAlarm

  • 5—equipmentAlarm

  • 6—environmentalAlarm

  • 7—integrityViolation

  • 8—operationalViolation

  • 9—physicalViolation

  • 10—securityServiceOrMechanismViolation

  • 11—timeDomainViolation

rbnSseAlarmDescription


SnmpAdminString


SIZE(0..64)

rbnFSGroupState


Integer:


  • 0—unknown

  • 1—up

  • 2—down

  • 3—partial

  • 4—stale

  • 5— noCard

  • 6—unassigned

rbnSseFsgSwitchFail


RBN-SSE-MIB

rbnSseAlarmDateAndTime


DateAndTime

rbnSseAlarmSeverity


Integer:


  • 1—cleared

  • 2— indeterminate

  • 3—critical

  • 4—major

  • 5—minor

  • 6—warning

 

rbnSseAlarmProbableCause


Integer:


  • 1—aIS

  • 2—callSetUpFailure

  • 3—degradedSignal

  • 4—farEndReceiverFailure

  • 5—framingError

  • 6—lossOfFrame

  • 7—lossOfPointer

  • 8—lossOfSignal

  • 9—payloadTypeMismatch

  • 10—transmissionError

  • 11—remoteAlarmInterface

  • 12—excessiveBER

  • 13—pathTraceMismatch

  • 14—unavailable

  • 15—signalLabelMismatch

  • 16—lossOfMultiFrame

  • 17—receiveFailure

  • 18—transmitFailure

  • 19—modulationFailure

  • 20—demodulationFailure

  • 21—broadcastChannelFailure

  • 22—connectionEstablishmentError

  • 23—invalidMessageReceived

  • 24—localNodeTransmissionError

  • 25—remoteNodeTransmissionError

  • 26—routingFailure

  • 51—backplaneFailure

  • 52—dataSetProblem

  • 53—equipmentIdentifierDuplication

  • 54—externalIFDeviceProblem

  • 55—lineCardProblem

  • 56—multiplexerProblem

  • 57—nEIdentifierDuplication

  • 58—powerProblem

  • 59—processorProblem

  • 60—protectionPathFailure

  • 61—receiverFailure

  • 62—replaceableUnitMissing

  • 63—replaceableUnitTypeMismatch

  • 64—synchronizationSourceMismatch

  • 65—terminalProblem

  • 66—timingProblem

  • 67—transmitterFailure

  • 68—trunkCardProblem

  • 69—replaceableUnitProblem

  • 70—realTimeClockFailure

  • 71—antennaFailure

  • 72—batteryChargingFailure

  • 73—diskFailure

  • 74—frequencyHoppingFailure

  • 75—iODeviceError

  • 76—lossOfSynchronisation

  • 77—lossOfRedundancy

  • 78—powerSupplyFailure

  • 79—signalQualityEvaluationFailure

  • 80—tranceiverFailure

  • 81—protectionMechanismFailure

  • 82—protectingResourceFailure

 
  • 101—airCompressorFailure

  • 102—airConditioningFailure

  • 103—airDryerFailure

  • 104—batteryDischarging

  • 105—batteryFailure

  • 106—commercialPowerFailure

  • 107—coolingFanFailure

  • 108—engineFailure

  • 109—fireDetectorFailure

  • 110—fuseFailure

  • 111—generatorFailure

  • 112—lowBatteryThreshold

  • 113—pumpFailure

  • 114—rectifierFailure

  • 115—rectifierHighVoltage

  • 116—rectifierLowFVoltage

  • 117—ventilationsSystemFailure

  • 118—enclosureDoorOpen

  • 119—explosiveGas120—fire

  • 121—flood

  • 122—highHumidity

  • 123—highTemperature

  • 124—highWind

  • 125—iceBuildUp

  • 126—intrusionDetection

  • 127—lowFuel

  • 128—lowHumidity

  • 129—lowCablePressure

  • 130—lowTemperatue

  • 131—lowWater

  • 132—smoke

  • 133—toxicGas

  • 134—coolingSystemFailure

  • 135—externalEquipmentFailure

  • 136—externalPointFailure

  • 151—storageCapacityProblem

  • 152—memoryMismatch

  • 153—corruptData

  • 154—outOfCPUCycles

  • 155—sfwrEnvironmentProblem

  • 156—sfwrDownloadFailure

  • 157—lossOfRealTimel

  • 158—applicationSubsystemFailure

  • 159—configurationOrCustomisationError

  • 160—databaseInconsistency

 
  • 161—fileError

  • 162—outOfMemory

  • 163—softwareError

  • 164—timeoutExpired

  • 165—underlayingResourceUnavailable

  • 166—versionMismatch

  • 201—bandwidthReduced

  • 202—congestion

  • 203—excessiveErrorRate

  • 204—excessiveResponseTime

  • 205—excessiveRetransmissionRate

  • 206—reducedLoggingCapability

  • 207—systemResourcesOverload

  • 500—adapterError

  • 501—applicationSubsystemFailture

  • 502—bandwidthReducedX733

  • 503—callEstablishmentError

  • 504—communicationsProtocolError

  • 505—communicationsSubsystemFailure

  • 506—configurationOrCustomizationError

  • 507—congestionX733

  • 508—coruptData

  • 509—cpuCyclesLimitExceeded

  • 510—dataSetOrModemError

  • 511—degradedSignalX733

  • 512—dteDceInterfaceError

  • 513—enclosureDoorOpenX733

  • 514—equipmentMalfunction

  • 515—excessiveVibration

  • 516—fileErrorX733

  • 517—fireDetected

  • 518—framingErrorX733

  • 519—heatingVentCoolingSystemProblem

  • 520—humidityUnacceptable

  • 521—inputOutputDeviceError

  • 522—inputDeviceError

  • 523—lanError

  • 524—leakDetected

  • 525—localNodeTransmissionErrorX733

  • 526—lossOfFrameX733

  • 527—lossOfSignalX733

  • 528—materialSupplyExhausted

  • 529—multiplexerProblemX733

  • 530—outOfMemoryX733

 
  • 531—ouputDeviceError

  • 532—performanceDegraded

  • 533—powerProblems

  • 534—pressureUnacceptable

  • 535—processorProblems

  • 536—pumpFailureX733

  • 537—queueSizeExceeded

  • 538—receiveFailureX733

  • 539—receiverFailureX733

  • 540—remoteNodeTransmissionErrorX733

  • 541—resourceAtOrNearingCapacity

  • 542—responseTimeExecessive

  • 543—retransmissionRateExcessive

  • 544—softwareErrorX733

  • 545—softwareProgramAbnormallyTerminated

  • 546—softwareProgramError

  • 547—storageCapacityProblemX733

  • 548—temperatureUnacceptable

  • 549—thresholdCrossed

  • 550—timingProblemX733

  • 551—toxicLeakDetected

  • 552—transmitFailureX733

  • 553—transmiterFailure

  • 554—underlyingResourceUnavailable

  • 555—versionMismatchX733

  • 600—authenticationFailure

  • 601—breachOfConfidentiality

  • 602—cableTamper

  • 603—delayedInformation

  • 604—denialOfService

  • 605—duplicateInformation

  • 606—informationMissing

  • 607—informationModificationDetectede

  • 608—informationOutOfSequence

  • 609—keyExpired

  • 610—nonRepudiationFailure

  • 611—outOfHoursActivity

  • 612—outOfServic

  • 613—proceduralError

  • 614—unauthorizedAccessAttempt

  • 615—unexpectedInformation

  • 1024—other

 

rbnSseEventType


Integer:


  • 1—other

  • 2—communicationsAlarm

  • 3—qualityOfServiceAlarm

  • 4—processingErrorAlarm

  • 5—equipmentAlarm

  • 6—environmentalAlarm

  • 7—integrityViolation

  • 8—operationalViolation

  • 9—physicalViolation

  • 10—securityServiceOrMechanismViolation

  • 11—timeDomainViolation

 

rbnSseAlarmDescription


SnmpAdminString


SIZE(0..64)

 

rbnFSGroupState


Integer:


  • 0—unknown

  • 1—up

  • 2—down

  • 3—partial

  • 4—stale

  • 5— noCard

  • 6—unassigned

rbnSseFsgSwitchWtr


RBN-SSE-MIB

rbnSseAlarmDateAndTime


DateAndTime

rbnSseAlarmSeverity


Integer:


  • 1—cleared

  • 2— indeterminate

  • 3—critical

  • 4—major

  • 5—minor

  • 6—warning

 

rbnSseAlarmProbableCause


Integer:


  • 1—aIS

  • 2—callSetUpFailure

  • 3—degradedSignal

  • 4—farEndReceiverFailure

  • 5—framingError

  • 6—lossOfFrame

  • 7—lossOfPointer

  • 8—lossOfSignal

  • 9—payloadTypeMismatch

  • 10—transmissionError

  • 11—remoteAlarmInterface

  • 12—excessiveBER

  • 13—pathTraceMismatch

  • 14—unavailable

  • 15—signalLabelMismatch

  • 16—lossOfMultiFrame

  • 17—receiveFailure

  • 18—transmitFailure

  • 19—modulationFailure

  • 20—demodulationFailure

  • 21—broadcastChannelFailure

  • 22—connectionEstablishmentError

  • 23—invalidMessageReceived

  • 24—localNodeTransmissionError

  • 25—remoteNodeTransmissionError

  • 26—routingFailure

  • 51—backplaneFailure

  • 52—dataSetProblem

  • 53—equipmentIdentifierDuplication

  • 54—externalIFDeviceProblem

  • 55—lineCardProblem

  • 56—multiplexerProblem

  • 57—nEIdentifierDuplication

  • 58—powerProblem

  • 59—processorProblem

  • 60—protectionPathFailure

  • 61—receiverFailure

  • 62—replaceableUnitMissing

  • 63—replaceableUnitTypeMismatch

  • 64—synchronizationSourceMismatch

  • 65—terminalProblem

  • 66—timingProblem

  • 67—transmitterFailure

  • 68—trunkCardProblem

  • 69—replaceableUnitProblem

  • 70—realTimeClockFailure

  • 71—antennaFailure

  • 72—batteryChargingFailure

  • 73—diskFailure

  • 74—frequencyHoppingFailure

  • 75—iODeviceError

  • 76—lossOfSynchronisation

  • 77—lossOfRedundancy

  • 78—powerSupplyFailure

  • 79—signalQualityEvaluationFailure

  • 80—tranceiverFailure

  • 81—protectionMechanismFailure

  • 82—protectingResourceFailure

 
  • 101—airCompressorFailure

  • 102—airConditioningFailure

  • 103—airDryerFailure

  • 104—batteryDischarging

  • 105—batteryFailure

  • 106—commercialPowerFailure

  • 107—coolingFanFailure

  • 108—engineFailure

  • 109—fireDetectorFailure

  • 110—fuseFailure

  • 111—generatorFailure

  • 112—lowBatteryThreshold

  • 113—pumpFailure

  • 114—rectifierFailure

  • 115—rectifierHighVoltage

  • 116—rectifierLowFVoltage

  • 117—ventilationsSystemFailure

  • 118—enclosureDoorOpen

  • 119—explosiveGas120—fire

  • 121—flood

  • 122—highHumidity

  • 123—highTemperature

  • 124—highWind

  • 125—iceBuildUp

  • 126—intrusionDetection

  • 127—lowFuel

  • 128—lowHumidity

  • 129—lowCablePressure

  • 130—lowTemperatue

  • 131—lowWater

  • 132—smoke

  • 133—toxicGas

  • 134—coolingSystemFailure

  • 135—externalEquipmentFailure

  • 136—externalPointFailure

  • 151—storageCapacityProblem

  • 152—memoryMismatch

  • 153—corruptData

  • 154—outOfCPUCycles

  • 155—sfwrEnvironmentProblem

  • 156—sfwrDownloadFailure

  • 157—lossOfRealTimel

  • 158—applicationSubsystemFailure

  • 159—configurationOrCustomisationError

  • 160—databaseInconsistency

 
  • 161—fileError

  • 162—outOfMemory

  • 163—softwareError

  • 164—timeoutExpired

  • 165—underlayingResourceUnavailable

  • 166—versionMismatch

  • 201—bandwidthReduced

  • 202—congestion

  • 203—excessiveErrorRate

  • 204—excessiveResponseTime

  • 205—excessiveRetransmissionRate

  • 206—reducedLoggingCapability

  • 207—systemResourcesOverload

  • 500—adapterError

  • 501—applicationSubsystemFailture

  • 502—bandwidthReducedX733

  • 503—callEstablishmentError

  • 504—communicationsProtocolError

  • 505—communicationsSubsystemFailure

  • 506—configurationOrCustomizationError

  • 507—congestionX733

  • 508—coruptData

  • 509—cpuCyclesLimitExceeded

  • 510—dataSetOrModemError

  • 511—degradedSignalX733

  • 512—dteDceInterfaceError

  • 513—enclosureDoorOpenX733

  • 514—equipmentMalfunction

  • 515—excessiveVibration

  • 516—fileErrorX733

  • 517—fireDetected

  • 518—framingErrorX733

  • 519—heatingVentCoolingSystemProblem

  • 520—humidityUnacceptable

  • 521—inputOutputDeviceError

  • 522—inputDeviceError

  • 523—lanError

  • 524—leakDetected

  • 525—localNodeTransmissionErrorX733

  • 526—lossOfFrameX733

  • 527—lossOfSignalX733

  • 528—materialSupplyExhausted

  • 529—multiplexerProblemX733

  • 530—outOfMemoryX733

 
  • 531—ouputDeviceError

  • 532—performanceDegraded

  • 533—powerProblems

  • 534—pressureUnacceptable

  • 535—processorProblems

  • 536—pumpFailureX733

  • 537—queueSizeExceeded

  • 538—receiveFailureX733

  • 539—receiverFailureX733

  • 540—remoteNodeTransmissionErrorX733

  • 541—resourceAtOrNearingCapacity

  • 542—responseTimeExecessive

  • 543—retransmissionRateExcessive

  • 544—softwareErrorX733

  • 545—softwareProgramAbnormallyTerminated

  • 546—softwareProgramError

  • 547—storageCapacityProblemX733

  • 548—temperatureUnacceptable

  • 549—thresholdCrossed

  • 550—timingProblemX733

  • 551—toxicLeakDetected

  • 552—transmitFailureX733

  • 553—transmiterFailure

  • 554—underlyingResourceUnavailable

  • 555—versionMismatchX733

  • 600—authenticationFailure

  • 601—breachOfConfidentiality

  • 602—cableTamper

  • 603—delayedInformation

  • 604—denialOfService

  • 605—duplicateInformation

  • 606—informationMissing

  • 607—informationModificationDetectede

  • 608—informationOutOfSequence

  • 609—keyExpired

  • 610—nonRepudiationFailure

  • 611—outOfHoursActivity

  • 612—outOfServic

  • 613—proceduralError

  • 614—unauthorizedAccessAttempt

  • 615—unexpectedInformation

  • 1024—other

 

rbnSseEventType


Integer:


  • 1—other

  • 2—communicationsAlarm

  • 3—qualityOfServiceAlarm

  • 4—processingErrorAlarm

  • 5—equipmentAlarm

  • 6—environmentalAlarm

  • 7—integrityViolation

  • 8—operationalViolation

  • 9—physicalViolation

  • 10—securityServiceOrMechanismViolation

  • 11—timeDomainViolation

 

rbnSseAlarmDescription


SnmpAdminString


SIZE(0..64)

 

rbnFSGroupState


Integer:


  • 0—unknown

  • 1—up

  • 2—down

  • 3—partial

  • 4—stale

  • 5— noCard

  • 6—unassigned

rbnSseFsgNotOperational


RBN-SSE-MIB

rbnSseAlarmDateAndTime


DateAndTime

 

rbnSseAlarmSeverity


Integer:


  • 1—cleared

  • 2— indeterminate

  • 3—critical

  • 4—major

  • 5—minor

  • 6—warning

 

rbnSseAlarmProbableCause


Integer:


  • 1—aIS

  • 2—callSetUpFailure

  • 3—degradedSignal

  • 4—farEndReceiverFailure

  • 5—framingError

  • 6—lossOfFrame

  • 7—lossOfPointer

  • 8—lossOfSignal

  • 9—payloadTypeMismatch

  • 10—transmissionError

  • 11—remoteAlarmInterface

  • 12—excessiveBER

  • 13—pathTraceMismatch

  • 14—unavailable

  • 15—signalLabelMismatch

  • 16—lossOfMultiFrame

  • 17—receiveFailure

  • 18—transmitFailure

  • 19—modulationFailure

  • 20—demodulationFailure

  • 21—broadcastChannelFailure

  • 22—connectionEstablishmentError

  • 23—invalidMessageReceived

  • 24—localNodeTransmissionError

  • 25—remoteNodeTransmissionError

  • 26—routingFailure

  • 51—backplaneFailure

  • 52—dataSetProblem

  • 53—equipmentIdentifierDuplication

  • 54—externalIFDeviceProblem

  • 55—lineCardProblem

  • 56—multiplexerProblem

  • 57—nEIdentifierDuplication

  • 58—powerProblem

  • 59—processorProblem

  • 60—protectionPathFailure

  • 61—receiverFailure

  • 62—replaceableUnitMissing

  • 63—replaceableUnitTypeMismatch

  • 64—synchronizationSourceMismatch

  • 65—terminalProblem

  • 66—timingProblem

  • 67—transmitterFailure

  • 68—trunkCardProblem

  • 69—replaceableUnitProblem

  • 70—realTimeClockFailure

  • 71—antennaFailure

  • 72—batteryChargingFailure

  • 73—diskFailure

  • 74—frequencyHoppingFailure

  • 75—iODeviceError

  • 76—lossOfSynchronisation

  • 77—lossOfRedundancy

  • 78—powerSupplyFailure

  • 79—signalQualityEvaluationFailure

  • 80—tranceiverFailure

  • 81—protectionMechanismFailure

  • 82—protectingResourceFailure

 
  • 101—airCompressorFailure

  • 102—airConditioningFailure

  • 103—airDryerFailure

  • 104—batteryDischarging

  • 105—batteryFailure

  • 106—commercialPowerFailure

  • 107—coolingFanFailure

  • 108—engineFailure

  • 109—fireDetectorFailure

  • 110—fuseFailure

  • 111—generatorFailure

  • 112—lowBatteryThreshold

  • 113—pumpFailure

  • 114—rectifierFailure

  • 115—rectifierHighVoltage

  • 116—rectifierLowFVoltage

  • 117—ventilationsSystemFailure

  • 118—enclosureDoorOpen

  • 119—explosiveGas120—fire

  • 121—flood

  • 122—highHumidity

  • 123—highTemperature

  • 124—highWind

  • 125—iceBuildUp

  • 126—intrusionDetection

  • 127—lowFuel

  • 128—lowHumidity

  • 129—lowCablePressure

  • 130—lowTemperatue

  • 131—lowWater

  • 132—smoke

  • 133—toxicGas

  • 134—coolingSystemFailure

  • 135—externalEquipmentFailure

  • 136—externalPointFailure

  • 151—storageCapacityProblem

  • 152—memoryMismatch

  • 153—corruptData

  • 154—outOfCPUCycles

  • 155—sfwrEnvironmentProblem

  • 156—sfwrDownloadFailure

  • 157—lossOfRealTimel

  • 158—applicationSubsystemFailure

  • 159—configurationOrCustomisationError

  • 160—databaseInconsistency

 
  • 161—fileError

  • 162—outOfMemory

  • 163—softwareError

  • 164—timeoutExpired

  • 165—underlayingResourceUnavailable

  • 166—versionMismatch

  • 201—bandwidthReduced

  • 202—congestion

  • 203—excessiveErrorRate

  • 204—excessiveResponseTime

  • 205—excessiveRetransmissionRate

  • 206—reducedLoggingCapability

  • 207—systemResourcesOverload

  • 500—adapterError

  • 501—applicationSubsystemFailture

  • 502—bandwidthReducedX733

  • 503—callEstablishmentError

  • 504—communicationsProtocolError

  • 505—communicationsSubsystemFailure

  • 506—configurationOrCustomizationError

  • 507—congestionX733

  • 508—coruptData

  • 509—cpuCyclesLimitExceeded

  • 510—dataSetOrModemError

  • 511—degradedSignalX733

  • 512—dteDceInterfaceError

  • 513—enclosureDoorOpenX733

  • 514—equipmentMalfunction

  • 515—excessiveVibration

  • 516—fileErrorX733

  • 517—fireDetected

  • 518—framingErrorX733

  • 519—heatingVentCoolingSystemProblem

  • 520—humidityUnacceptable

  • 521—inputOutputDeviceError

  • 522—inputDeviceError

  • 523—lanError

  • 524—leakDetected

  • 525—localNodeTransmissionErrorX733

  • 526—lossOfFrameX733

  • 527—lossOfSignalX733

  • 528—materialSupplyExhausted

  • 529—multiplexerProblemX733

  • 530—outOfMemoryX733

 
  • 531—ouputDeviceError

  • 532—performanceDegraded

  • 533—powerProblems

  • 534—pressureUnacceptable

  • 535—processorProblems

  • 536—pumpFailureX733

  • 537—queueSizeExceeded

  • 538—receiveFailureX733

  • 539—receiverFailureX733

  • 540—remoteNodeTransmissionErrorX733

  • 541—resourceAtOrNearingCapacity

  • 542—responseTimeExecessive

  • 543—retransmissionRateExcessive

  • 544—softwareErrorX733

  • 545—softwareProgramAbnormallyTerminated

  • 546—softwareProgramError

  • 547—storageCapacityProblemX733

  • 548—temperatureUnacceptable

  • 549—thresholdCrossed

  • 550—timingProblemX733

  • 551—toxicLeakDetected

  • 552—transmitFailureX733

  • 553—transmiterFailure

  • 554—underlyingResourceUnavailable

  • 555—versionMismatchX733

  • 600—authenticationFailure

  • 601—breachOfConfidentiality

  • 602—cableTamper

  • 603—delayedInformation

  • 604—denialOfService

  • 605—duplicateInformation

  • 606—informationMissing

  • 607—informationModificationDetectede

  • 608—informationOutOfSequence

  • 609—keyExpired

  • 610—nonRepudiationFailure

  • 611—outOfHoursActivity

  • 612—outOfServic

  • 613—proceduralError

  • 614—unauthorizedAccessAttempt

  • 615—unexpectedInformation

  • 1024—other

 

rbnSseEventType


INTEGER


  • 1—other

  • 2—communicationsAlarm

  • 3—qualityOfServiceAlarm

  • 4—processingErrorAlarm

  • 5—equipmentAlarm

  • 6—environmentalAlarm

  • 7—integrityViolation

  • 8—operationalViolation

  • 9—physicalViolation

  • 10—securityServiceOrMechanismViolation

  • 11—timeDomainViolation

 

rbnSseAlarmDescription


SnmpAdminString


SIZE(0..64)

 

rbnFSGroupState


Integer:


  • 0—unknown

  • 1—up

  • 2—down

  • 3—partial

  • 4—stale

  • 5— noCard

  • 6—unassigned

rbnSseFsgBlockDeviceFail


RBN-SSE-MIB

rbnSseAlarmDateAndTime


DateAndTime

 

rbnSseAlarmSeverity


Integer:


  • 1—cleared

  • 2— indeterminate

  • 3—critical

  • 4—major

  • 5—minor

  • 6—warning

 

rbnSseAlarmProbableCause


Integer:


  • 1—aIS

  • 2—callSetUpFailure

  • 3—degradedSignal

  • 4—farEndReceiverFailure

  • 5—framingError

  • 6—lossOfFrame

  • 7—lossOfPointer

  • 8—lossOfSignal

  • 9—payloadTypeMismatch

  • 10—transmissionError

  • 11—remoteAlarmInterface

  • 12—excessiveBER

  • 13—pathTraceMismatch

  • 14—unavailable

  • 15—signalLabelMismatch

  • 16—lossOfMultiFrame

  • 17—receiveFailure

  • 18—transmitFailure

  • 19—modulationFailure

  • 20—demodulationFailure

  • 21—broadcastChannelFailure

  • 22—connectionEstablishmentError

  • 23—invalidMessageReceived

  • 24—localNodeTransmissionError

  • 25—remoteNodeTransmissionError

  • 26—routingFailure

  • 51—backplaneFailure

  • 52—dataSetProblem

  • 53—equipmentIdentifierDuplication

  • 54—externalIFDeviceProblem

  • 55—lineCardProblem

  • 56—multiplexerProblem

  • 57—nEIdentifierDuplication

  • 58—powerProblem

  • 59—processorProblem

  • 60—protectionPathFailure

  • 61—receiverFailure

  • 62—replaceableUnitMissing

  • 63—replaceableUnitTypeMismatch

  • 64—synchronizationSourceMismatch

  • 65—terminalProblem

  • 66—timingProblem

  • 67—transmitterFailure

  • 68—trunkCardProblem

  • 69—replaceableUnitProblem

  • 70—realTimeClockFailure

  • 71—antennaFailure

  • 72—batteryChargingFailure

  • 73—diskFailure

  • 74—frequencyHoppingFailure

  • 75—iODeviceError

  • 76—lossOfSynchronisation

  • 77—lossOfRedundancy

  • 78—powerSupplyFailure

  • 79—signalQualityEvaluationFailure

  • 80—tranceiverFailure

  • 81—protectionMechanismFailure

  • 82—protectingResourceFailure

 
  • 101—airCompressorFailure

  • 102—airConditioningFailure

  • 103—airDryerFailure

  • 104—batteryDischarging

  • 105—batteryFailure

  • 106—commercialPowerFailure

  • 107—coolingFanFailure

  • 108—engineFailure

  • 109—fireDetectorFailure

  • 110—fuseFailure

  • 111—generatorFailure

  • 112—lowBatteryThreshold

  • 113—pumpFailure

  • 114—rectifierFailure

  • 115—rectifierHighVoltage

  • 116—rectifierLowFVoltage

  • 117—ventilationsSystemFailure

  • 118—enclosureDoorOpen

  • 119—explosiveGas120—fire

  • 121—flood

  • 122—highHumidity

  • 123—highTemperature

  • 124—highWind

  • 125—iceBuildUp

  • 126—intrusionDetection

  • 127—lowFuel

  • 128—lowHumidity

  • 129—lowCablePressure

  • 130—lowTemperatue

  • 131—lowWater

  • 132—smoke

  • 133—toxicGas

  • 134—coolingSystemFailure

  • 135—externalEquipmentFailure

  • 136—externalPointFailure

  • 151—storageCapacityProblem

  • 152—memoryMismatch

  • 153—corruptData

  • 154—outOfCPUCycles

  • 155—sfwrEnvironmentProblem

  • 156—sfwrDownloadFailure

  • 157—lossOfRealTimel

  • 158—applicationSubsystemFailure

  • 159—configurationOrCustomisationError

  • 160—databaseInconsistency

 
  • 161—fileError

  • 162—outOfMemory

  • 163—softwareError

  • 164—timeoutExpired

  • 165—underlayingResourceUnavailable

  • 166—versionMismatch

  • 201—bandwidthReduced

  • 202—congestion

  • 203—excessiveErrorRate

  • 204—excessiveResponseTime

  • 205—excessiveRetransmissionRate

  • 206—reducedLoggingCapability

  • 207—systemResourcesOverload

  • 500—adapterError

  • 501—applicationSubsystemFailture

  • 502—bandwidthReducedX733

  • 503—callEstablishmentError

  • 504—communicationsProtocolError

  • 505—communicationsSubsystemFailure

  • 506—configurationOrCustomizationError

  • 507—congestionX733

  • 508—coruptData

  • 509—cpuCyclesLimitExceeded

  • 510—dataSetOrModemError

  • 511—degradedSignalX733

  • 512—dteDceInterfaceError

  • 513—enclosureDoorOpenX733

  • 514—equipmentMalfunction

  • 515—excessiveVibration

  • 516—fileErrorX733

  • 517—fireDetected

  • 518—framingErrorX733

  • 519—heatingVentCoolingSystemProblem

  • 520—humidityUnacceptable

  • 521—inputOutputDeviceError

  • 522—inputDeviceError

  • 523—lanError

  • 524—leakDetected

  • 525—localNodeTransmissionErrorX733

  • 526—lossOfFrameX733

  • 527—lossOfSignalX733

  • 528—materialSupplyExhausted

  • 529—multiplexerProblemX733

  • 530—outOfMemoryX733

 
  • 531—ouputDeviceError

  • 532—performanceDegraded

  • 533—powerProblems

  • 534—pressureUnacceptable

  • 535—processorProblems

  • 536—pumpFailureX733

  • 537—queueSizeExceeded

  • 538—receiveFailureX733

  • 539—receiverFailureX733

  • 540—remoteNodeTransmissionErrorX733

  • 541—resourceAtOrNearingCapacity

  • 542—responseTimeExecessive

  • 543—retransmissionRateExcessive

  • 544—softwareErrorX733

  • 545—softwareProgramAbnormallyTerminated

  • 546—softwareProgramError

  • 547—storageCapacityProblemX733

  • 548—temperatureUnacceptable

  • 549—thresholdCrossed

  • 550—timingProblemX733

  • 551—toxicLeakDetected

  • 552—transmitFailureX733

  • 553—transmiterFailure

  • 554—underlyingResourceUnavailable

  • 555—versionMismatchX733

  • 600—authenticationFailure

  • 601—breachOfConfidentiality

  • 602—cableTamper

  • 603—delayedInformation

  • 604—denialOfService

  • 605—duplicateInformation

  • 606—informationMissing

  • 607—informationModificationDetectede

  • 608—informationOutOfSequence

  • 609—keyExpired

  • 610—nonRepudiationFailure

  • 611—outOfHoursActivity

  • 612—outOfServic

  • 613—proceduralError

  • 614—unauthorizedAccessAttempt

  • 615—unexpectedInformation

  • 1024—other

 

rbnSseEventType


Integer:


  • 1—other

  • 2—communicationsAlarm

  • 3—qualityOfServiceAlarm

  • 4—processingErrorAlarm

  • 5—equipmentAlarm

  • 6—environmentalAlarm

  • 7—integrityViolation

  • 8—operationalViolation

  • 9—physicalViolation

  • 10—securityServiceOrMechanismViolation

  • 11—timeDomainViolation

 

rbnSseAlarmDescription


SnmpAdminString


SIZE(0..64)

 

rbnFSGroupState


Integer:


  • 0—unknown

  • 1—up

  • 2—down

  • 3—partial

  • 4—stale

  • 5— noCard

  • 6—unassigned

rbnSseFsgPartitionNotOperational


RBN-SSE-MIB

rbnSseAlarmDateAndTime


DateAndTime

 

rbnSseAlarmSeverity


Integer:


  • 1—cleared

  • 2— indeterminate

  • 3—critical

  • 4—major

  • 5—minor

  • 6—warning

 

rbnSseAlarmProbableCause


Integer:


  • 1—aIS

  • 2—callSetUpFailure

  • 3—degradedSignal

  • 4—farEndReceiverFailure

  • 5—framingError

  • 6—lossOfFrame

  • 7—lossOfPointer

  • 8—lossOfSignal

  • 9—payloadTypeMismatch

  • 10—transmissionError

  • 11—remoteAlarmInterface

  • 12—excessiveBER

  • 13—pathTraceMismatch

  • 14—unavailable

  • 15—signalLabelMismatch

  • 16—lossOfMultiFrame

  • 17—receiveFailure

  • 18—transmitFailure

  • 19—modulationFailure

  • 20—demodulationFailure

  • 21—broadcastChannelFailure

  • 22—connectionEstablishmentError

  • 23—invalidMessageReceived

  • 24—localNodeTransmissionError

  • 25—remoteNodeTransmissionError

  • 26—routingFailure

  • 51—backplaneFailure

  • 52—dataSetProblem

  • 53—equipmentIdentifierDuplication

  • 54—externalIFDeviceProblem

  • 55—lineCardProblem

  • 56—multiplexerProblem

  • 57—nEIdentifierDuplication

  • 58—powerProblem

  • 59—processorProblem

  • 60—protectionPathFailure

  • 61—receiverFailure

  • 62—replaceableUnitMissing

  • 63—replaceableUnitTypeMismatch

  • 64—synchronizationSourceMismatch

  • 65—terminalProblem

  • 66—timingProblem

  • 67—transmitterFailure

  • 68—trunkCardProblem

  • 69—replaceableUnitProblem

  • 70—realTimeClockFailure

  • 71—antennaFailure

  • 72—batteryChargingFailure

  • 73—diskFailure

  • 74—frequencyHoppingFailure

  • 75—iODeviceError

  • 76—lossOfSynchronisation

  • 77—lossOfRedundancy

  • 78—powerSupplyFailure

  • 79—signalQualityEvaluationFailure

  • 80—tranceiverFailure

  • 81—protectionMechanismFailure

  • 82—protectingResourceFailure

 
  • 101—airCompressorFailure

  • 102—airConditioningFailure

  • 103—airDryerFailure

  • 104—batteryDischarging

  • 105—batteryFailure

  • 106—commercialPowerFailure

  • 107—coolingFanFailure

  • 108—engineFailure

  • 109—fireDetectorFailure

  • 110—fuseFailure

  • 111—generatorFailure

  • 112—lowBatteryThreshold

  • 113—pumpFailure

  • 114—rectifierFailure

  • 115—rectifierHighVoltage

  • 116—rectifierLowFVoltage

  • 117—ventilationsSystemFailure

  • 118—enclosureDoorOpen

  • 119—explosiveGas120—fire

  • 121—flood

  • 122—highHumidity

  • 123—highTemperature

  • 124—highWind

  • 125—iceBuildUp

  • 126—intrusionDetection

  • 127—lowFuel

  • 128—lowHumidity

  • 129—lowCablePressure

  • 130—lowTemperatue

  • 131—lowWater

  • 132—smoke

  • 133—toxicGas

  • 134—coolingSystemFailure

  • 135—externalEquipmentFailure

  • 136—externalPointFailure

  • 151—storageCapacityProblem

  • 152—memoryMismatch

  • 153—corruptData

  • 154—outOfCPUCycles

  • 155—sfwrEnvironmentProblem

  • 156—sfwrDownloadFailure

  • 157—lossOfRealTimel

  • 158—applicationSubsystemFailure

  • 159—configurationOrCustomisationError

  • 160—databaseInconsistency

 
  • 161—fileError

  • 162—outOfMemory

  • 163—softwareError

  • 164—timeoutExpired

  • 165—underlayingResourceUnavailable

  • 166—versionMismatch

  • 201—bandwidthReduced

  • 202—congestion

  • 203—excessiveErrorRate

  • 204—excessiveResponseTime

  • 205—excessiveRetransmissionRate

  • 206—reducedLoggingCapability

  • 207—systemResourcesOverload

  • 500—adapterError

  • 501—applicationSubsystemFailture

  • 502—bandwidthReducedX733

  • 503—callEstablishmentError

  • 504—communicationsProtocolError

  • 505—communicationsSubsystemFailure

  • 506—configurationOrCustomizationError

  • 507—congestionX733

  • 508—coruptData

  • 509—cpuCyclesLimitExceeded

  • 510—dataSetOrModemError

  • 511—degradedSignalX733

  • 512—dteDceInterfaceError

  • 513—enclosureDoorOpenX733

  • 514—equipmentMalfunction

  • 515—excessiveVibration

  • 516—fileErrorX733

  • 517—fireDetected

  • 518—framingErrorX733

  • 519—heatingVentCoolingSystemProblem

  • 520—humidityUnacceptable

  • 521—inputOutputDeviceError

  • 522—inputDeviceError

  • 523—lanError

  • 524—leakDetected

  • 525—localNodeTransmissionErrorX733

  • 526—lossOfFrameX733

  • 527—lossOfSignalX733

  • 528—materialSupplyExhausted

  • 529—multiplexerProblemX733

  • 530—outOfMemoryX733

 
  • 531—ouputDeviceError

  • 532—performanceDegraded

  • 533—powerProblems

  • 534—pressureUnacceptable

  • 535—processorProblems

  • 536—pumpFailureX733

  • 537—queueSizeExceeded

  • 538—receiveFailureX733

  • 539—receiverFailureX733

  • 540—remoteNodeTransmissionErrorX733

  • 541—resourceAtOrNearingCapacity

  • 542—responseTimeExecessive

  • 543—retransmissionRateExcessive

  • 544—softwareErrorX733

  • 545—softwareProgramAbnormallyTerminated

  • 546—softwareProgramError

  • 547—storageCapacityProblemX733

  • 548—temperatureUnacceptable

  • 549—thresholdCrossed

  • 550—timingProblemX733

  • 551—toxicLeakDetected

  • 552—transmitFailureX733

  • 553—transmiterFailure

  • 554—underlyingResourceUnavailable

  • 555—versionMismatchX733

  • 600—authenticationFailure

  • 601—breachOfConfidentiality

  • 602—cableTamper

  • 603—delayedInformation

  • 604—denialOfService

  • 605—duplicateInformation

  • 606—informationMissing

  • 607—informationModificationDetectede

  • 608—informationOutOfSequence

  • 609—keyExpired

  • 610—nonRepudiationFailure

  • 611—outOfHoursActivity

  • 612—outOfServic

  • 613—proceduralError

  • 614—unauthorizedAccessAttempt

  • 615—unexpectedInformation

  • 1024—other

 

rbnSseEventType


Integer:


  • 1—other

  • 2—communicationsAlarm

  • 3—qualityOfServiceAlarm

  • 4—processingErrorAlarm

  • 5—equipmentAlarm

  • 6—environmentalAlarm

  • 7—integrityViolation

  • 8—operationalViolation

  • 9—physicalViolation

  • 10—securityServiceOrMechanismViolation

  • 11—timeDomainViolation

 

rbnSseAlarmDescription


SnmpAdminString


SIZE(0..64)

 

rbnFSGroupState


Integer:


  • 0—unknown

  • 1—up

  • 2—down

  • 3—partial

  • 4—stale

  • 5— noCard

  • 6—unassigned

rbnSseFsgParitionDataSyncing


RBN-SSE-MIB

rbnSseAlarmDateAndTime


DateAndTime

 

rbnSseAlarmSeverity


Integer:


  • 1—cleared

  • 2— indeterminate

  • 3—critical

  • 4—major

  • 5—minor

  • 6—warning

 

rbnSseAlarmProbableCause


Integer:


  • 1—aIS

  • 2—callSetUpFailure

  • 3—degradedSignal

  • 4—farEndReceiverFailure

  • 5—framingError

  • 6—lossOfFrame

  • 7—lossOfPointer

  • 8—lossOfSignal

  • 9—payloadTypeMismatch

  • 10—transmissionError

  • 11—remoteAlarmInterface

  • 12—excessiveBER

  • 13—pathTraceMismatch

  • 14—unavailable

  • 15—signalLabelMismatch

  • 16—lossOfMultiFrame

  • 17—receiveFailure

  • 18—transmitFailure

  • 19—modulationFailure

  • 20—demodulationFailure

  • 21—broadcastChannelFailure

  • 22—connectionEstablishmentError

  • 23—invalidMessageReceived

  • 24—localNodeTransmissionError

  • 25—remoteNodeTransmissionError

  • 26—routingFailure

  • 51—backplaneFailure

  • 52—dataSetProblem

  • 53—equipmentIdentifierDuplication

  • 54—externalIFDeviceProblem

  • 55—lineCardProblem

  • 56—multiplexerProblem

  • 57—nEIdentifierDuplication

  • 58—powerProblem

  • 59—processorProblem

  • 60—protectionPathFailure

  • 61—receiverFailure

  • 62—replaceableUnitMissing

  • 63—replaceableUnitTypeMismatch

  • 64—synchronizationSourceMismatch

  • 65—terminalProblem

  • 66—timingProblem

  • 67—transmitterFailure

  • 68—trunkCardProblem

  • 69—replaceableUnitProblem

  • 70—realTimeClockFailure

  • 71—antennaFailure

  • 72—batteryChargingFailure

  • 73—diskFailure

  • 74—frequencyHoppingFailure

  • 75—iODeviceError

  • 76—lossOfSynchronisation

  • 77—lossOfRedundancy

  • 78—powerSupplyFailure

  • 79—signalQualityEvaluationFailure

  • 80—tranceiverFailure

  • 81—protectionMechanismFailure

  • 82—protectingResourceFailure

 
  • 101—airCompressorFailure

  • 102—airConditioningFailure

  • 103—airDryerFailure

  • 104—batteryDischarging

  • 105—batteryFailure

  • 106—commercialPowerFailure

  • 107—coolingFanFailure

  • 108—engineFailure

  • 109—fireDetectorFailure

  • 110—fuseFailure

  • 111—generatorFailure

  • 112—lowBatteryThreshold

  • 113—pumpFailure

  • 114—rectifierFailure

  • 115—rectifierHighVoltage

  • 116—rectifierLowFVoltage

  • 117—ventilationsSystemFailure

  • 118—enclosureDoorOpen

  • 119—explosiveGas120—fire

  • 121—flood

  • 122—highHumidity

  • 123—highTemperature

  • 124—highWind

  • 125—iceBuildUp

  • 126—intrusionDetection

  • 127—lowFuel

  • 128—lowHumidity

  • 129—lowCablePressure

  • 130—lowTemperatue

  • 131—lowWater

  • 132—smoke

  • 133—toxicGas

  • 134—coolingSystemFailure

  • 135—externalEquipmentFailure

  • 136—externalPointFailure

  • 151—storageCapacityProblem

  • 152—memoryMismatch

  • 153—corruptData

  • 154—outOfCPUCycles

  • 155—sfwrEnvironmentProblem

  • 156—sfwrDownloadFailure

  • 157—lossOfRealTimel

  • 158—applicationSubsystemFailure

  • 159—configurationOrCustomisationError

  • 160—databaseInconsistency

 
  • 161—fileError

  • 162—outOfMemory

  • 163—softwareError

  • 164—timeoutExpired

  • 165—underlayingResourceUnavailable

  • 166—versionMismatch

  • 201—bandwidthReduced

  • 202—congestion

  • 203—excessiveErrorRate

  • 204—excessiveResponseTime

  • 205—excessiveRetransmissionRate

  • 206—reducedLoggingCapability

  • 207—systemResourcesOverload

  • 500—adapterError

  • 501—applicationSubsystemFailture

  • 502—bandwidthReducedX733

  • 503—callEstablishmentError

  • 504—communicationsProtocolError

  • 505—communicationsSubsystemFailure

  • 506—configurationOrCustomizationError

  • 507—congestionX733

  • 508—coruptData

  • 509—cpuCyclesLimitExceeded

  • 510—dataSetOrModemError

  • 511—degradedSignalX733

  • 512—dteDceInterfaceError

  • 513—enclosureDoorOpenX733

  • 514—equipmentMalfunction

  • 515—excessiveVibration

  • 516—fileErrorX733

  • 517—fireDetected

  • 518—framingErrorX733

  • 519—heatingVentCoolingSystemProblem

  • 520—humidityUnacceptable

  • 521—inputOutputDeviceError

  • 522—inputDeviceError

  • 523—lanError

  • 524—leakDetected

  • 525—localNodeTransmissionErrorX733

  • 526—lossOfFrameX733

  • 527—lossOfSignalX733

  • 528—materialSupplyExhausted

  • 529—multiplexerProblemX733

  • 530—outOfMemoryX733

 
  • 531—ouputDeviceError

  • 532—performanceDegraded

  • 533—powerProblems

  • 534—pressureUnacceptable

  • 535—processorProblems

  • 536—pumpFailureX733

  • 537—queueSizeExceeded

  • 538—receiveFailureX733

  • 539—receiverFailureX733

  • 540—remoteNodeTransmissionErrorX733

  • 541—resourceAtOrNearingCapacity

  • 542—responseTimeExecessive

  • 543—retransmissionRateExcessive

  • 544—softwareErrorX733

  • 545—softwareProgramAbnormallyTerminated

  • 546—softwareProgramError

  • 547—storageCapacityProblemX733

  • 548—temperatureUnacceptable

  • 549—thresholdCrossed

  • 550—timingProblemX733

  • 551—toxicLeakDetected

  • 552—transmitFailureX733

  • 553—transmiterFailure

  • 554—underlyingResourceUnavailable

  • 555—versionMismatchX733

  • 600—authenticationFailure

  • 601—breachOfConfidentiality

  • 602—cableTamper

  • 603—delayedInformation

  • 604—denialOfService

  • 605—duplicateInformation

  • 606—informationMissing

  • 607—informationModificationDetectede

  • 608—informationOutOfSequence

  • 609—keyExpired

  • 610—nonRepudiationFailure

  • 611—outOfHoursActivity

  • 612—outOfServic

  • 613—proceduralError

  • 614—unauthorizedAccessAttempt

  • 615—unexpectedInformation

  • 1024—other

 

rbnSseEventType


Integer:


  • 1—other

  • 2—communicationsAlarm

  • 3—qualityOfServiceAlarm

  • 4—processingErrorAlarm

  • 5—equipmentAlarm

  • 6—environmentalAlarm

  • 7—integrityViolation

  • 8—operationalViolation

  • 9—physicalViolation

  • 10—securityServiceOrMechanismViolation

  • 11—timeDomainViolation

 

rbnSseAlarmDescription


SnmpAdminString


SIZE(0..64)

 

rbnFSGroupState


Integer:


  • 0—unknown

  • 1—up

  • 2—down

  • 3—partial

  • 4—stale

  • 5— noCard

  • 6—unassigned

rbnSseFsgParitionDataSyncFail


RBN-SSE-MIB

rbnSseAlarmDateAndTime


DateAndTime

 

rbnSseAlarmSeverity


Integer:


  • 1—cleared

  • 2— indeterminate

  • 3—critical

  • 4—major

  • 5—minor

  • 6—warning

 

rbnSseAlarmProbableCause


Integer:


  • 1—aIS

  • 2—callSetUpFailure

  • 3—degradedSignal

  • 4—farEndReceiverFailure

  • 5—framingError

  • 6—lossOfFrame

  • 7—lossOfPointer

  • 8—lossOfSignal

  • 9—payloadTypeMismatch

  • 10—transmissionError

  • 11—remoteAlarmInterface

  • 12—excessiveBER

  • 13—pathTraceMismatch

  • 14—unavailable

  • 15—signalLabelMismatch

  • 16—lossOfMultiFrame

  • 17—receiveFailure

  • 18—transmitFailure

  • 19—modulationFailure

  • 20—demodulationFailure

  • 21—broadcastChannelFailure

  • 22—connectionEstablishmentError

  • 23—invalidMessageReceived

  • 24—localNodeTransmissionError

  • 25—remoteNodeTransmissionError

  • 26—routingFailure

  • 51—backplaneFailure

  • 52—dataSetProblem

  • 53—equipmentIdentifierDuplication

  • 54—externalIFDeviceProblem

  • 55—lineCardProblem

  • 56—multiplexerProblem

  • 57—nEIdentifierDuplication

  • 58—powerProblem

  • 59—processorProblem

  • 60—protectionPathFailure

  • 61—receiverFailure

  • 62—replaceableUnitMissing

  • 63—replaceableUnitTypeMismatch

  • 64—synchronizationSourceMismatch

  • 65—terminalProblem

  • 66—timingProblem

  • 67—transmitterFailure

  • 68—trunkCardProblem

  • 69—replaceableUnitProblem

  • 70—realTimeClockFailure

  • 71—antennaFailure

  • 72—batteryChargingFailure

  • 73—diskFailure

  • 74—frequencyHoppingFailure

  • 75—iODeviceError

  • 76—lossOfSynchronisation

  • 77—lossOfRedundancy

  • 78—powerSupplyFailure

  • 79—signalQualityEvaluationFailure

  • 80—tranceiverFailure

  • 81—protectionMechanismFailure

  • 82—protectingResourceFailure

 
  • 101—airCompressorFailure

  • 102—airConditioningFailure

  • 103—airDryerFailure

  • 104—batteryDischarging

  • 105—batteryFailure

  • 106—commercialPowerFailure

  • 107—coolingFanFailure

  • 108—engineFailure

  • 109—fireDetectorFailure

  • 110—fuseFailure

  • 111—generatorFailure

  • 112—lowBatteryThreshold

  • 113—pumpFailure

  • 114—rectifierFailure

  • 115—rectifierHighVoltage

  • 116—rectifierLowFVoltage

  • 117—ventilationsSystemFailure

  • 118—enclosureDoorOpen

  • 119—explosiveGas120—fire

  • 121—flood

  • 122—highHumidity

  • 123—highTemperature

  • 124—highWind

  • 125—iceBuildUp

  • 126—intrusionDetection

  • 127—lowFuel

  • 128—lowHumidity

  • 129—lowCablePressure

  • 130—lowTemperatue

  • 131—lowWater

  • 132—smoke

  • 133—toxicGas

  • 134—coolingSystemFailure

  • 135—externalEquipmentFailure

  • 136—externalPointFailure

  • 151—storageCapacityProblem

  • 152—memoryMismatch

  • 153—corruptData

  • 154—outOfCPUCycles

  • 155—sfwrEnvironmentProblem

  • 156—sfwrDownloadFailure

  • 157—lossOfRealTimel

  • 158—applicationSubsystemFailure

  • 159—configurationOrCustomisationError

  • 160—databaseInconsistency

 
  • 161—fileError

  • 162—outOfMemory

  • 163—softwareError

  • 164—timeoutExpired

  • 165—underlayingResourceUnavailable

  • 166—versionMismatch

  • 201—bandwidthReduced

  • 202—congestion

  • 203—excessiveErrorRate

  • 204—excessiveResponseTime

  • 205—excessiveRetransmissionRate

  • 206—reducedLoggingCapability

  • 207—systemResourcesOverload

  • 500—adapterError

  • 501—applicationSubsystemFailture

  • 502—bandwidthReducedX733

  • 503—callEstablishmentError

  • 504—communicationsProtocolError

  • 505—communicationsSubsystemFailure

  • 506—configurationOrCustomizationError

  • 507—congestionX733

  • 508—coruptData

  • 509—cpuCyclesLimitExceeded

  • 510—dataSetOrModemError

  • 511—degradedSignalX733

  • 512—dteDceInterfaceError

  • 513—enclosureDoorOpenX733

  • 514—equipmentMalfunction

  • 515—excessiveVibration

  • 516—fileErrorX733

  • 517—fireDetected

  • 518—framingErrorX733

  • 519—heatingVentCoolingSystemProblem

  • 520—humidityUnacceptable

  • 521—inputOutputDeviceError

  • 522—inputDeviceError

  • 523—lanError

  • 524—leakDetected

  • 525—localNodeTransmissionErrorX733

  • 526—lossOfFrameX733

  • 527—lossOfSignalX733

  • 528—materialSupplyExhausted

  • 529—multiplexerProblemX733

  • 530—outOfMemoryX733

 
  • 531—ouputDeviceError

  • 532—performanceDegraded

  • 533—powerProblems

  • 534—pressureUnacceptable

  • 535—processorProblems

  • 536—pumpFailureX733

  • 537—queueSizeExceeded

  • 538—receiveFailureX733

  • 539—receiverFailureX733

  • 540—remoteNodeTransmissionErrorX733

  • 541—resourceAtOrNearingCapacity

  • 542—responseTimeExecessive

  • 543—retransmissionRateExcessive

  • 544—softwareErrorX733

  • 545—softwareProgramAbnormallyTerminated

  • 546—softwareProgramError

  • 547—storageCapacityProblemX733

  • 548—temperatureUnacceptable

  • 549—thresholdCrossed

  • 550—timingProblemX733

  • 551—toxicLeakDetected

  • 552—transmitFailureX733

  • 553—transmiterFailure

  • 554—underlyingResourceUnavailable

  • 555—versionMismatchX733

  • 600—authenticationFailure

  • 601—breachOfConfidentiality

  • 602—cableTamper

  • 603—delayedInformation

  • 604—denialOfService

  • 605—duplicateInformation

  • 606—informationMissing

  • 607—informationModificationDetectede

  • 608—informationOutOfSequence

  • 609—keyExpired

  • 610—nonRepudiationFailure

  • 611—outOfHoursActivity

  • 612—outOfServic

  • 613—proceduralError

  • 614—unauthorizedAccessAttempt

  • 615—unexpectedInformation

  • 1024—other

 

rbnSseEventType


Integer:


  • 1—other

  • 2—communicationsAlarm

  • 3—qualityOfServiceAlarm

  • 4—processingErrorAlarm

  • 5—equipmentAlarm

  • 6—environmentalAlarm

  • 7—integrityViolation

  • 8—operationalViolation

  • 9—physicalViolation

  • 10—securityServiceOrMechanismViolation

  • 11—timeDomainViolation

 

rbnSseAlarmDescription


SnmpAdminString


SIZE(0..64)

 

rbnFSGroupState


Integer:


  • 0—unknown

  • 1—up

  • 2—down

  • 3—partial

  • 4—stale

  • 5— noCard

  • 6—unassigned

rbnSseFsgPartitionFull


RBN-SSE-MIB

rbnSseAlarmDateAndTime


DateAndTime

 

rbnSseAlarmSeverity


Integer:


  • 1—cleared

  • 2— indeterminate

  • 3—critical

  • 4—major

  • 5—minor

  • 6—warning

 

rbnSseAlarmProbableCause


Integer:


  • 1—aIS

  • 2—callSetUpFailure

  • 3—degradedSignal

  • 4—farEndReceiverFailure

  • 5—framingError

  • 6—lossOfFrame

  • 7—lossOfPointer

  • 8—lossOfSignal

  • 9—payloadTypeMismatch

  • 10—transmissionError

  • 11—remoteAlarmInterface

  • 12—excessiveBER

  • 13—pathTraceMismatch

  • 14—unavailable

  • 15—signalLabelMismatch

  • 16—lossOfMultiFrame

  • 17—receiveFailure

  • 18—transmitFailure

  • 19—modulationFailure

  • 20—demodulationFailure

  • 21—broadcastChannelFailure

  • 22—connectionEstablishmentError

  • 23—invalidMessageReceived

  • 24—localNodeTransmissionError

  • 25—remoteNodeTransmissionError

  • 26—routingFailure

  • 51—backplaneFailure

  • 52—dataSetProblem

  • 53—equipmentIdentifierDuplication

  • 54—externalIFDeviceProblem

  • 55—lineCardProblem

  • 56—multiplexerProblem

  • 57—nEIdentifierDuplication

  • 58—powerProblem

  • 59—processorProblem

  • 60—protectionPathFailure

  • 61—receiverFailure

  • 62—replaceableUnitMissing

  • 63—replaceableUnitTypeMismatch

  • 64—synchronizationSourceMismatch

  • 65—terminalProblem

  • 66—timingProblem

  • 67—transmitterFailure

  • 68—trunkCardProblem

  • 69—replaceableUnitProblem

  • 70—realTimeClockFailure

  • 71—antennaFailure

  • 72—batteryChargingFailure

  • 73—diskFailure

  • 74—frequencyHoppingFailure

  • 75—iODeviceError

  • 76—lossOfSynchronisation

  • 77—lossOfRedundancy

  • 78—powerSupplyFailure

  • 79—signalQualityEvaluationFailure

  • 80—tranceiverFailure

  • 81—protectionMechanismFailure

  • 82—protectingResourceFailure

 
  • 101—airCompressorFailure

  • 102—airConditioningFailure

  • 103—airDryerFailure

  • 104—batteryDischarging

  • 105—batteryFailure

  • 106—commercialPowerFailure

  • 107—coolingFanFailure

  • 108—engineFailure

  • 109—fireDetectorFailure

  • 110—fuseFailure

  • 111—generatorFailure

  • 112—lowBatteryThreshold

  • 113—pumpFailure

  • 114—rectifierFailure

  • 115—rectifierHighVoltage

  • 116—rectifierLowFVoltage

  • 117—ventilationsSystemFailure

  • 118—enclosureDoorOpen

  • 119—explosiveGas120—fire

  • 121—flood

  • 122—highHumidity

  • 123—highTemperature

  • 124—highWind

  • 125—iceBuildUp

  • 126—intrusionDetection

  • 127—lowFuel

  • 128—lowHumidity

  • 129—lowCablePressure

  • 130—lowTemperatue

  • 131—lowWater

  • 132—smoke

  • 133—toxicGas

  • 134—coolingSystemFailure

  • 135—externalEquipmentFailure

  • 136—externalPointFailure

  • 151—storageCapacityProblem

  • 152—memoryMismatch

  • 153—corruptData

  • 154—outOfCPUCycles

  • 155—sfwrEnvironmentProblem

  • 156—sfwrDownloadFailure

  • 157—lossOfRealTimel

  • 158—applicationSubsystemFailure

  • 159—configurationOrCustomisationError

  • 160—databaseInconsistency

 
  • 161—fileError

  • 162—outOfMemory

  • 163—softwareError

  • 164—timeoutExpired

  • 165—underlayingResourceUnavailable

  • 166—versionMismatch

  • 201—bandwidthReduced

  • 202—congestion

  • 203—excessiveErrorRate

  • 204—excessiveResponseTime

  • 205—excessiveRetransmissionRate

  • 206—reducedLoggingCapability

  • 207—systemResourcesOverload

  • 500—adapterError

  • 501—applicationSubsystemFailture

  • 502—bandwidthReducedX733

  • 503—callEstablishmentError

  • 504—communicationsProtocolError

  • 505—communicationsSubsystemFailure

  • 506—configurationOrCustomizationError

  • 507—congestionX733

  • 508—coruptData

  • 509—cpuCyclesLimitExceeded

  • 510—dataSetOrModemError

  • 511—degradedSignalX733

  • 512—dteDceInterfaceError

  • 513—enclosureDoorOpenX733

  • 514—equipmentMalfunction

  • 515—excessiveVibration

  • 516—fileErrorX733

  • 517—fireDetected

  • 518—framingErrorX733

  • 519—heatingVentCoolingSystemProblem

  • 520—humidityUnacceptable

  • 521—inputOutputDeviceError

  • 522—inputDeviceError

  • 523—lanError

  • 524—leakDetected

  • 525—localNodeTransmissionErrorX733

  • 526—lossOfFrameX733

  • 527—lossOfSignalX733

  • 528—materialSupplyExhausted

  • 529—multiplexerProblemX733

  • 530—outOfMemoryX733

 
  • 531—ouputDeviceError

  • 532—performanceDegraded

  • 533—powerProblems

  • 534—pressureUnacceptable

  • 535—processorProblems

  • 536—pumpFailureX733

  • 537—queueSizeExceeded

  • 538—receiveFailureX733

  • 539—receiverFailureX733

  • 540—remoteNodeTransmissionErrorX733

  • 541—resourceAtOrNearingCapacity

  • 542—responseTimeExecessive

  • 543—retransmissionRateExcessive

  • 544—softwareErrorX733

  • 545—softwareProgramAbnormallyTerminated

  • 546—softwareProgramError

  • 547—storageCapacityProblemX733

  • 548—temperatureUnacceptable

  • 549—thresholdCrossed

  • 550—timingProblemX733

  • 551—toxicLeakDetected

  • 552—transmitFailureX733

  • 553—transmiterFailure

  • 554—underlyingResourceUnavailable

  • 555—versionMismatchX733

  • 600—authenticationFailure

  • 601—breachOfConfidentiality

  • 602—cableTamper

  • 603—delayedInformation

  • 604—denialOfService

  • 605—duplicateInformation

  • 606—informationMissing

  • 607—informationModificationDetectede

  • 608—informationOutOfSequence

  • 609—keyExpired

  • 610—nonRepudiationFailure

  • 611—outOfHoursActivity

  • 612—outOfServic

  • 613—proceduralError

  • 614—unauthorizedAccessAttempt

  • 615—unexpectedInformation

  • 1024—other

 

rbnSseEventType


Integer:


  • 1—other

  • 2—communicationsAlarm

  • 3—qualityOfServiceAlarm

  • 4—processingErrorAlarm

  • 5—equipmentAlarm

  • 6—environmentalAlarm

  • 7—integrityViolation

  • 8—operationalViolation

  • 9—physicalViolation

  • 10—securityServiceOrMechanismViolation

  • 11—timeDomainViolation

 

rbnSseAlarmDescription


SnmpAdminString


SIZE(0..64)

 

rbnFSGroupState


Integer:


  • 0—unknown

  • 1—up

  • 2—down

  • 3—partial

  • 4—stale

  • 5— noCard

  • 6—unassigned

rbnSseFsgPartitionLow


RBN-SSE-MIB

rbnSseAlarmDateAndTime


DateAndTime

rbnSseAlarmSeverity


Integer:


  • 1—cleared

  • 2— indeterminate

  • 3—critical

  • 4—major

  • 5—minor

  • 6—warning

 

rbnSseAlarmProbableCause


Integer:


  • 1—aIS

  • 2—callSetUpFailure

  • 3—degradedSignal

  • 4—farEndReceiverFailure

  • 5—framingError

  • 6—lossOfFrame

  • 7—lossOfPointer

  • 8—lossOfSignal

  • 9—payloadTypeMismatch

  • 10—transmissionError

  • 11—remoteAlarmInterface

  • 12—excessiveBER

  • 13—pathTraceMismatch

  • 14—unavailable

  • 15—signalLabelMismatch

  • 16—lossOfMultiFrame

  • 17—receiveFailure

  • 18—transmitFailure

  • 19—modulationFailure

  • 20—demodulationFailure

  • 21—broadcastChannelFailure

  • 22—connectionEstablishmentError

  • 23—invalidMessageReceived

  • 24—localNodeTransmissionError

  • 25—remoteNodeTransmissionError

  • 26—routingFailure

  • 51—backplaneFailure

  • 52—dataSetProblem

  • 53—equipmentIdentifierDuplication

  • 54—externalIFDeviceProblem

  • 55—lineCardProblem

  • 56—multiplexerProblem

  • 57—nEIdentifierDuplication

  • 58—powerProblem

  • 59—processorProblem

  • 60—protectionPathFailure

  • 61—receiverFailure

  • 62—replaceableUnitMissing

  • 63—replaceableUnitTypeMismatch

  • 64—synchronizationSourceMismatch

  • 65—terminalProblem

  • 66—timingProblem

  • 67—transmitterFailure

  • 68—trunkCardProblem

  • 69—replaceableUnitProblem

  • 70—realTimeClockFailure

  • 71—antennaFailure

  • 72—batteryChargingFailure

  • 73—diskFailure

  • 74—frequencyHoppingFailure

  • 75—iODeviceError

  • 76—lossOfSynchronisation

  • 77—lossOfRedundancy

  • 78—powerSupplyFailure

  • 79—signalQualityEvaluationFailure

  • 80—tranceiverFailure

  • 81—protectionMechanismFailure

  • 82—protectingResourceFailure

 
  • 101—airCompressorFailure

  • 102—airConditioningFailure

  • 103—airDryerFailure

  • 104—batteryDischarging

  • 105—batteryFailure

  • 106—commercialPowerFailure

  • 107—coolingFanFailure

  • 108—engineFailure

  • 109—fireDetectorFailure

  • 110—fuseFailure

  • 111—generatorFailure

  • 112—lowBatteryThreshold

  • 113—pumpFailure

  • 114—rectifierFailure

  • 115—rectifierHighVoltage

  • 116—rectifierLowFVoltage

  • 117—ventilationsSystemFailure

  • 118—enclosureDoorOpen

  • 119—explosiveGas120—fire

  • 121—flood

  • 122—highHumidity

  • 123—highTemperature

  • 124—highWind

  • 125—iceBuildUp

  • 126—intrusionDetection

  • 127—lowFuel

  • 128—lowHumidity

  • 129—lowCablePressure

  • 130—lowTemperatue

  • 131—lowWater

  • 132—smoke

  • 133—toxicGas

  • 134—coolingSystemFailure

  • 135—externalEquipmentFailure

  • 136—externalPointFailure

  • 151—storageCapacityProblem

  • 152—memoryMismatch

  • 153—corruptData

  • 154—outOfCPUCycles

  • 155—sfwrEnvironmentProblem

  • 156—sfwrDownloadFailure

  • 157—lossOfRealTimel

  • 158—applicationSubsystemFailure

  • 159—configurationOrCustomisationError

  • 160—databaseInconsistency

 
  • 161—fileError

  • 162—outOfMemory

  • 163—softwareError

  • 164—timeoutExpired

  • 165—underlayingResourceUnavailable

  • 166—versionMismatch

  • 201—bandwidthReduced

  • 202—congestion

  • 203—excessiveErrorRate

  • 204—excessiveResponseTime

  • 205—excessiveRetransmissionRate

  • 206—reducedLoggingCapability

  • 207—systemResourcesOverload

  • 500—adapterError

  • 501—applicationSubsystemFailture

  • 502—bandwidthReducedX733

  • 503—callEstablishmentError

  • 504—communicationsProtocolError

  • 505—communicationsSubsystemFailure

  • 506—configurationOrCustomizationError

  • 507—congestionX733

  • 508—coruptData

  • 509—cpuCyclesLimitExceeded

  • 510—dataSetOrModemError

  • 511—degradedSignalX733

  • 512—dteDceInterfaceError

  • 513—enclosureDoorOpenX733

  • 514—equipmentMalfunction

  • 515—excessiveVibration

  • 516—fileErrorX733

  • 517—fireDetected

  • 518—framingErrorX733

  • 519—heatingVentCoolingSystemProblem

  • 520—humidityUnacceptable

  • 521—inputOutputDeviceError

  • 522—inputDeviceError

  • 523—lanError

  • 524—leakDetected

  • 525—localNodeTransmissionErrorX733

  • 526—lossOfFrameX733

  • 527—lossOfSignalX733

  • 528—materialSupplyExhausted

  • 529—multiplexerProblemX733

  • 530—outOfMemoryX733

 
  • 531—ouputDeviceError

  • 532—performanceDegraded

  • 533—powerProblems

  • 534—pressureUnacceptable

  • 535—processorProblems

  • 536—pumpFailureX733

  • 537—queueSizeExceeded

  • 538—receiveFailureX733

  • 539—receiverFailureX733

  • 540—remoteNodeTransmissionErrorX733

  • 541—resourceAtOrNearingCapacity

  • 542—responseTimeExecessive

  • 543—retransmissionRateExcessive

  • 544—softwareErrorX733

  • 545—softwareProgramAbnormallyTerminated

  • 546—softwareProgramError

  • 547—storageCapacityProblemX733

  • 548—temperatureUnacceptable

  • 549—thresholdCrossed

  • 550—timingProblemX733

  • 551—toxicLeakDetected

  • 552—transmitFailureX733

  • 553—transmiterFailure

  • 554—underlyingResourceUnavailable

  • 555—versionMismatchX733

  • 600—authenticationFailure

  • 601—breachOfConfidentiality

  • 602—cableTamper

  • 603—delayedInformation

  • 604—denialOfService

  • 605—duplicateInformation

  • 606—informationMissing

  • 607—informationModificationDetectede

  • 608—informationOutOfSequence

  • 609—keyExpired

  • 610—nonRepudiationFailure

  • 611—outOfHoursActivity

  • 612—outOfServic

  • 613—proceduralError

  • 614—unauthorizedAccessAttempt

  • 615—unexpectedInformation

  • 1024—other

 

rbnSseEventType


Integer:


  • 1—other

  • 2—communicationsAlarm

  • 3—qualityOfServiceAlarm

  • 4—processingErrorAlarm

  • 5—equipmentAlarm

  • 6—environmentalAlarm

  • 7—integrityViolation

  • 8—operationalViolation

  • 9—physicalViolation

  • 10—securityServiceOrMechanismViolation

  • 11—timeDomainViolation

 

rbnSseAlarmDescription


SnmpAdminString


SIZE(0..64)

 

rbnFSGroupState


Integer:


  • 0—unknown

  • 1—up

  • 2—down

  • 3—partial

  • 4—stale

  • 5— noCard

  • 6—unassigned

rbnSseFsgPartitionNotOperStandby


RBN-SSE-MIB

rbnSseAlarmDateAndTime


DateAndTime

 

rbnSseAlarmSeverity


Integer:


  • 1—cleared

  • 2— indeterminate

  • 3—critical

  • 4—major

  • 5—minor

  • 6—warning

 

rbnSseAlarmProbableCause


Integer:


  • 1—aIS

  • 2—callSetUpFailure

  • 3—degradedSignal

  • 4—farEndReceiverFailure

  • 5—framingError

  • 6—lossOfFrame

  • 7—lossOfPointer

  • 8—lossOfSignal

  • 9—payloadTypeMismatch

  • 10—transmissionError

  • 11—remoteAlarmInterface

  • 12—excessiveBER

  • 13—pathTraceMismatch

  • 14—unavailable

  • 15—signalLabelMismatch

  • 16—lossOfMultiFrame

  • 17—receiveFailure

  • 18—transmitFailure

  • 19—modulationFailure

  • 20—demodulationFailure

  • 21—broadcastChannelFailure

  • 22—connectionEstablishmentError

  • 23—invalidMessageReceived

  • 24—localNodeTransmissionError

  • 25—remoteNodeTransmissionError

  • 26—routingFailure

  • 51—backplaneFailure

  • 52—dataSetProblem

  • 53—equipmentIdentifierDuplication

  • 54—externalIFDeviceProblem

  • 55—lineCardProblem

  • 56—multiplexerProblem

  • 57—nEIdentifierDuplication

  • 58—powerProblem

  • 59—processorProblem

  • 60—protectionPathFailure

  • 61—receiverFailure

  • 62—replaceableUnitMissing

  • 63—replaceableUnitTypeMismatch

  • 64—synchronizationSourceMismatch

  • 65—terminalProblem

  • 66—timingProblem

  • 67—transmitterFailure

  • 68—trunkCardProblem

  • 69—replaceableUnitProblem

  • 70—realTimeClockFailure

  • 71—antennaFailure

  • 72—batteryChargingFailure

  • 73—diskFailure

  • 74—frequencyHoppingFailure

  • 75—iODeviceError

  • 76—lossOfSynchronisation

  • 77—lossOfRedundancy

  • 78—powerSupplyFailure

  • 79—signalQualityEvaluationFailure

  • 80—tranceiverFailure

  • 81—protectionMechanismFailure

  • 82—protectingResourceFailure

 
  • 101—airCompressorFailure

  • 102—airConditioningFailure

  • 103—airDryerFailure

  • 104—batteryDischarging

  • 105—batteryFailure

  • 106—commercialPowerFailure

  • 107—coolingFanFailure

  • 108—engineFailure

  • 109—fireDetectorFailure

  • 110—fuseFailure

  • 111—generatorFailure

  • 112—lowBatteryThreshold

  • 113—pumpFailure

  • 114—rectifierFailure

  • 115—rectifierHighVoltage

  • 116—rectifierLowFVoltage

  • 117—ventilationsSystemFailure

  • 118—enclosureDoorOpen

  • 119—explosiveGas120—fire

  • 121—flood

  • 122—highHumidity

  • 123—highTemperature

  • 124—highWind

  • 125—iceBuildUp

  • 126—intrusionDetection

  • 127—lowFuel

  • 128—lowHumidity

  • 129—lowCablePressure

  • 130—lowTemperatue

  • 131—lowWater

  • 132—smoke

  • 133—toxicGas

  • 134—coolingSystemFailure

  • 135—externalEquipmentFailure

  • 136—externalPointFailure

  • 151—storageCapacityProblem

  • 152—memoryMismatch

  • 153—corruptData

  • 154—outOfCPUCycles

  • 155—sfwrEnvironmentProblem

  • 156—sfwrDownloadFailure

  • 157—lossOfRealTimel

  • 158—applicationSubsystemFailure

  • 159—configurationOrCustomisationError

  • 160—databaseInconsistency

 
  • 161—fileError

  • 162—outOfMemory

  • 163—softwareError

  • 164—timeoutExpired

  • 165—underlayingResourceUnavailable

  • 166—versionMismatch

  • 201—bandwidthReduced

  • 202—congestion

  • 203—excessiveErrorRate

  • 204—excessiveResponseTime

  • 205—excessiveRetransmissionRate

  • 206—reducedLoggingCapability

  • 207—systemResourcesOverload

  • 500—adapterError

  • 501—applicationSubsystemFailture

  • 502—bandwidthReducedX733

  • 503—callEstablishmentError

  • 504—communicationsProtocolError

  • 505—communicationsSubsystemFailure

  • 506—configurationOrCustomizationError

  • 507—congestionX733

  • 508—coruptData

  • 509—cpuCyclesLimitExceeded

  • 510—dataSetOrModemError

  • 511—degradedSignalX733

  • 512—dteDceInterfaceError

  • 513—enclosureDoorOpenX733

  • 514—equipmentMalfunction

  • 515—excessiveVibration

  • 516—fileErrorX733

  • 517—fireDetected

  • 518—framingErrorX733

  • 519—heatingVentCoolingSystemProblem

  • 520—humidityUnacceptable

  • 521—inputOutputDeviceError

  • 522—inputDeviceError

  • 523—lanError

  • 524—leakDetected

  • 525—localNodeTransmissionErrorX733

  • 526—lossOfFrameX733

  • 527—lossOfSignalX733

  • 528—materialSupplyExhausted

  • 529—multiplexerProblemX733

  • 530—outOfMemoryX733

 
  • 531—ouputDeviceError

  • 532—performanceDegraded

  • 533—powerProblems

  • 534—pressureUnacceptable

  • 535—processorProblems

  • 536—pumpFailureX733

  • 537—queueSizeExceeded

  • 538—receiveFailureX733

  • 539—receiverFailureX733

  • 540—remoteNodeTransmissionErrorX733

  • 541—resourceAtOrNearingCapacity

  • 542—responseTimeExecessive

  • 543—retransmissionRateExcessive

  • 544—softwareErrorX733

  • 545—softwareProgramAbnormallyTerminated

  • 546—softwareProgramError

  • 547—storageCapacityProblemX733

  • 548—temperatureUnacceptable

  • 549—thresholdCrossed

  • 550—timingProblemX733

  • 551—toxicLeakDetected

  • 552—transmitFailureX733

  • 553—transmiterFailure

  • 554—underlyingResourceUnavailable

  • 555—versionMismatchX733

  • 600—authenticationFailure

  • 601—breachOfConfidentiality

  • 602—cableTamper

  • 603—delayedInformation

  • 604—denialOfService

  • 605—duplicateInformation

  • 606—informationMissing

  • 607—informationModificationDetectede

  • 608—informationOutOfSequence

  • 609—keyExpired

  • 610—nonRepudiationFailure

  • 611—outOfHoursActivity

  • 612—outOfServic

  • 613—proceduralError

  • 614—unauthorizedAccessAttempt

  • 615—unexpectedInformation

  • 1024—other

 

rbnSseEventType


Integer:


  • 1—other

  • 2—communicationsAlarm

  • 3—qualityOfServiceAlarm

  • 4—processingErrorAlarm

  • 5—equipmentAlarm

  • 6—environmentalAlarm

  • 7—integrityViolation

  • 8—operationalViolation

  • 9—physicalViolation

  • 10—securityServiceOrMechanismViolation

  • 11—timeDomainViolation

 

rbnSseAlarmDescription


SnmpAdminString


SIZE(0..64)

 

rbnFSGroupState


Integer:


  • 0—unknown

  • 1—up

  • 2—down

  • 3—partial

  • 4—stale

  • 5— noCard

  • 6—unassigned