Copyright |
© Ericsson AB 2009–2011. All rights reserved. No part of this document may be reproduced in any form without the written permission of the copyright owner. | ||||||
Disclaimer |
The contents of this document are subject to revision without notice due to continued progress in methodology, design and manufacturing. Ericsson shall have no liability for any error or damage of any kind resulting from the use of this document. | ||||||
Trademark List |
|

1 Command Descriptions
Commands starting with “show r” through commands starting with “show z” are included.
1.1 show radius control
show radius control
1.1.1 Purpose
Displays Remote Authentication Dial-In User Service (RADIUS) server control information.
1.1.2 Command Mode
All modes
1.1.3 Syntax Description
This command has no keywords or arguments.
1.1.4 Default
None
1.1.5 Usage Guidelines
Use the show radius control command to display RADIUS server control information.
Table 1 describes the information displayed in the output of the show radius control command. The display represents a snapshot of the current status of the message processing being handled by the RADIUS server or servers.
Field |
Description |
---|---|
Number of servers |
Total number of RADIUS servers in the context or contexts |
Total slots |
Total number of possible outstanding requests for all servers in the context or contexts |
Total in waiting queue |
Number of requests waiting to be processed for all servers in the context or contexts |
Total in process queue |
Number of requests currently being processed for all servers in the context or contexts |
Server status |
Full means no more requests can be handled OK means not full |
- Note:
- By default, most show commands (in any mode) display information for the current context only or, depending on the command syntax, for all contexts. If you are an administrator for the local context, you can insert the optional context ctx-name construct, preceding the show command, to view output for the specified context without entering that context. For more information about using the context ctx-name construct, see the context command description.
- Note:
- By appending a space followed by the pipe ( | ) character at the end of a show command, you can filter the output using a set of modifier keywords and arguments. For more information, see Modifying Output of show Commands in Using the CLI.
1.1.6 Examples
The following example displays output from the show radius control command:
[local]Redback>show radius control ========================================================= Context Name: local --------------------------------------------------------- Authentication Accounting Number of servers: 1 1 Total slots: 256 256 Total in hi_waiting queue: 0 0 Total in low_waiting queue: 0 0 Total in hi_process queue: 0 0 Total in low_process queue: 0 0 Total in waiting queue: 0 0 Total in process queue: 0 0 Server status: Ok Ok
1.2 show radius counters
show radius counters
1.2.1 Purpose
Displays counters for Remote Authentication Dial-In User Service (RADIUS) access, accounting, Change of Authorization (CoA) messages, and counters related to route downloads.
1.2.2 Command Mode
all modes
1.2.3 Syntax Description
This command has no keywords or arguments.
1.2.4 Default
None
1.2.5 Usage Guidelines
Use the show radius counters command to display RADIUS access and accounting message counters. If the RADIUS server is configured as a CoA server, this command also displays CoA server counters.
Table 2 describes the counters that are displayed in the output of the show radius counters command.
Field |
Description |
---|---|
Access Messages | |
Requests sent |
Number of access request messages sent |
Requests retried |
Number of access request retry messages sent |
Requests send fail |
Number of access request messages that were sent and failed |
Requests timeout |
Number of access request messages that timed out |
Responses drop |
Number of access request messages that were dropped |
Accepts received |
Number of access accept messages received |
Rejects received |
Number of access reject messages received |
Accounting Messages | |
Requests sent |
Number of accounting request messages sent |
Requests retry |
Number of accounting request retry messages sent |
Requests send fail |
Number of accounting request messages that were sent and failed |
Requests timeout |
Number of accounting request messages that timed out |
Responses drop |
Number of accounting request messages that were dropped |
Responses received |
Number of accounting request message responses received |
CoA Messages | |
Requests received |
Number of CoA and disconnect request messages received |
Duplicate request |
Number of duplicate CoA and disconnect request messages received |
Response ACK |
Number of CoA and disconnect requests that were successful |
Response NAK |
Number of CoA and disconnect requests that were unsuccessful |
- Note:
- By default, most show commands (in any mode) display information for the current context only or, depending on the command syntax, for all contexts. If you are an administrator for the local context, you can insert the optional context ctx-name construct, preceding the show command, to view output for the specified context without entering that context. For more information about using the context ctx-name construct, see context command.
- Note:
- By appending a space followed by the pipe ( | ) character at the end of a show command, you can filter the output using a set of modifier keywords and arguments. For more information, see Modifying Output of show Commands in Using the CLI.
1.2.6 Examples
The following example displays output from the show radius counters command:
[local]Redback>show radius counters ============================================================================= Server: 10.13.130.75 Port: 1812 Counter start time: May 23 17:55:30 2006 ----------------------------------------------------------------------------- Access Messages: ----------------------------------------------------------------------------- Requests sent: 0 Requests retried: 0 Requests send fail: 0 Requests timeout: 0 Responses dropped: 0 Accepts received: 0 Rejects received: 0 ============================================================================= Server: 10.13.130.75 Port: 1813 Counter start time: May 22 23:41:09 2006 ----------------------------------------------------------------------------- Accounting Messages: ----------------------------------------------------------------------------- Requests sent: 356 Requests retried: 1 Requests send fail: 0 Requests timeout: 0 Responses dropped: 0 Accepts received: 357 Rejects received: 0 ============================================================================= Server: 10.13.130.75 Port: 3799 Counter start time: May 22 23:52:35 2006 ----------------------------------------------------------------------------- CoA Messages: ----------------------------------------------------------------------------- Requests received: 12 Duplicate request: 0 Response ACK: 6 Response NAK: 6
This example displays the output for the show radius counters command with AAA route-download information.
[local]Redback>show radius counters ============================================================================= Server: 10.18.18.33 Port: 1850 Counter start time: Jun 15 23:28:07 2010 ----------------------------------------------------------------------------- Route Download Messages: ----------------------------------------------------------------------------- Requests sent: 1335 Requests retried: 0 Requests send fail: 0 Requests timeout: 0 Responses dropped: 0 Accepts received: 1334 Rejects received: 1
1.3 show radius server
show radius server
1.3.1 Purpose
Displays Remote Authentication Dial-In User Service (RADIUS) server configuration, status information, and route download server information .
1.3.2 Command Mode
all modes
1.3.3 Syntax Description
This command has no keywords or arguments.
1.3.4 Default
None
1.3.5 Usage Guidelines
Use the show radius server command to display RADIUS server configuration and status information. If the RADIUS server is configured as a Change of Authorization (CoA) server, this command also displays CoA server information.
- Note:
- By default, most show commands (in any mode) display information for the current context only or, depending on the command syntax, for all contexts. If you are an administrator for the local context, you can insert the optional context ctx-name construct, preceding the show command, to view output for the specified context without entering that context. For more information about using the context ctx-name construct, see the context command description.
- Note:
- By appending a space followed by the pipe ( | ) character at the end of a show command, you can filter the output using a set of modifier keywords and arguments. For more information, see Modifying Output of show Commands in Using the CLI.
1.3.6 Examples
The following example displays RADIUS server configuration information and status:
[local]redback#show radius server Authentication Server ============================================================================== Address Port Key State State set time ============================================================================== 155.53.129.64 1812 ******** Init Fri Mar 12 19:07:33 2010 Algorithm: first Timeout (in sec.): 5 Max retry: 1 Max outstanding: 256 Server timeout (in sec.): 60 Deadtime (in min.): 5 Accounting Server ============================================================================== Address Port Key State State set time ============================================================================== 155.53.129.64 1813 ******** Alive Fri Mar 12 19:08:02 2010 Algorithm: first Timeout (in sec.): 10 Max retry: 3 Max outstanding: 256 Server timeout (in sec.): 60 Deadtime (in min.): 5 Interim timeout: 0 Interim max retry: 0 CoA Server ============================================================================== Address Port Key State State set time ============================================================================== 1.1.1.1 3799 ******** Init Fri Mar 12 19:07:33 2010 1.1.1.2 3800 ******** Init Fri Mar 12 19:07:33 2010 1.1.1.3 3801 ******** Init Fri Mar 12 19:07:33 2010 1.1.1.4 3802 ******** Init Fri Mar 12 19:07:33 2010 1.1.1.5 3803 ******** Init Fri Mar 12 19:07:33 2010 1.1.1.6 3804 ******** Init Fri Mar 12 19:07:33 2010 1.1.1.7 3805 ******** Init Fri Mar 12 19:07:33 2010 1.1.1.8 3806 ******** Init Fri Mar 12 19:07:33 2010 1.1.1.9 3807 ******** Init Fri Mar 12 19:07:33 2010 1.1.1.10 3808 ******** Init Fri Mar 12 19:07:33 2010 1.1.1.11 3809 ******** Init Fri Mar 12 19:07:33 2010 1.1.1.12 3810 ******** Init Fri Mar 12 19:07:33 2010 1.1.1.13 3811 ******** Init Fri Mar 12 19:07:33 2010 1.1.1.14 3812 ******** Init Fri Mar 12 19:07:33 2010 1.1.1.15 3813 ******** Init Fri Mar 12 19:07:33 2010 1.1.1.16 3814 ******** Init Fri Mar 12 19:07:33 2010 1.1.1.17 3815 ******** Init Fri Mar 12 19:07:33 2010 1.1.1.18 3816 ******** Init Fri Mar 12 19:07:33 2010 1.1.1.19 3817 ******** Init Fri Mar 12 19:07:33 2010 1.1.1.20 3818 ******** Init Fri Mar 12 19:07:33 2010 1.1.1.21 3819 ******** Init Fri Mar 12 19:07:33 2010 1.1.1.22 3820 ******** Init Fri Mar 12 19:07:33 2010 1.1.1.23 3821 ******** Init Fri Mar 12 19:07:33 2010 1.1.1.24 3822 ******** Init Fri Mar 12 19:07:33 2010 1.1.1.25 3823 ******** Init Fri Mar 12 19:07:33 2010 1.1.1.26 3824 ******** Init Fri Mar 12 19:07:33 2010 1.1.1.27 3825 ******** Init Fri Mar 12 19:07:33 2010 1.1.1.28 3826 ******** Init Fri Mar 12 19:07:33 2010 1.1.1.29 3827 ******** Init Fri Mar 12 19:07:33 2010 1.1.1.30 3828 ******** Init Fri Mar 12 19:07:33 2010 1.1.1.31 3829 ******** Init Fri Mar 12 19:07:33 2010 1.1.1.32 3830 ******** Init Fri Mar 12 19:07:33 2010 1.1.1.33 3831 ******** Init Fri Mar 12 19:07:33 2010 1.1.1.34 3832 ******** Init Fri Mar 12 19:07:33 2010 1.1.1.35 3833 ******** Init Fri Mar 12 19:07:33 2010 1.1.1.36 3834 ******** Init Fri Mar 12 19:07:33 2010
The following example displays RADIUS server configuration information with AAA route download information:
[local]Redback>show radius server
Route Download Server ============================================================================== Address Port Key State State set time ============================================================================== 10.18.18.33 1850 ******** Alive Tue Jun 15 23:28:39 2010 Algorithm: first Timeout (in sec.): 10 Max retry: 3 Server timeout (in sec.): 60 Deadtime (in min.): 5
1.4 show radius statistics
show radius statistics
1.4.1 Purpose
Displays Remote Authentication Dial-In User Service (RADIUS) server statistics and statistics related to route downloads.
1.4.2 Command Mode
all modes
1.4.3 Syntax Description
This command has no keywords or arguments.
1.4.4 Default
None
1.4.5 Usage Guidelines
Use the show radius statistics command to display RADIUS server statistics.
Table 3 describes the counters that are displayed in the output of the show radius statistics command.
Field |
Description |
---|---|
Authentication Servers |
|
Requests send |
Number of access request messages sent. |
Requests re-send |
Number of access-requests sent more than one time by the SmartEdge® router to the RADIUS servers (NetOp™ PM) because the timeout set (command radius timeout) in the configuration is over |
Requests timeout |
Number of access request messages that timed out |
Requests send fail |
Number of access request messages that were sent and failed |
Requests accepted |
Number of access-accepts received by the SmartEdge router from the RADIUS servers (NetOp PM) |
Requests rejected |
Number of access-rejects received by the SmartEdge router from the RADIUS servers (NetOp PM) |
Response dropped |
Number of access request messages that were dropped |
Req in process |
Total number of access-requests outstanding from the SmartEdge router . |
Req in waiting |
Number of subscribers waiting for an available slot to send the access-request to the RADIUS servers. |
Server slots |
Total number of simultaneous access-requests that can out stand from the SmartEdge router . |
Capacity |
Percentage of server slots currently in use. |
Server marked dead |
Number of RADIUS servers known as dead at the moment the show command was typed. |
Accounting Servers |
|
Requests send |
Number of access request messages sent. |
Requests re-send |
Number of access-requests sent more than one time by the SmartEdge router to the RADIUS servers (NetOp PM) because the timeout set (command radius timeout) in the configuration is over |
Requests timeout |
Number of access request messages that timed out |
Requests send fail |
Number of access request messages that were sent and failed |
Requests accepted |
Number of access-accepts received by the SmartEdge router from the RADIUS servers (NetOp PM) |
Requests rejected |
Number of access-rejects received by the SmartEdge router from the RADIUS servers (NetOp PM) |
Response dropped |
Number of access request messages that were dropped |
Req in process |
Total number of access-requests outstanding from the SmartEdge router . |
Req in waiting |
Number of subscribers waiting for an available slot to send the access-request to the RADIUS servers. |
Server slots |
Total number of simultaneous access-requests that can out stand from the SmartEdge router . |
Capacity |
Percentage of server slots currently in use. |
Server marked dead |
Number of RADIUS servers known as dead at the moment the show command was typed. |
- Note:
- By default, most show commands (in any mode) display information for the current context only or, depending on the command syntax, for all contexts. If you are an administrator for the local context, you can insert the optional context ctx-name construct, preceding the show command, to view output for the specified context without entering that context. For more information about using the context ctx-name construct, see the context command description.
- Note:
- By appending a space followed by the pipe ( | ) character at the end of a show command, you can filter the output using a set of modifier keywords and arguments. For more information, see Modifying Output of show Commands in Using the CLI.
1.4.6 Examples
The following example displays RADIUS statistics:
[local]Redback>show radius statistics ============================================================================= Server: 155.53.129.64 Port: 1812 Counter start time: Mar 12 20:50:57 2010 ----------------------------------------------------------------------------- Access Messages: ----------------------------------------------------------------------------- Requests sent: 0 Requests retried: 0 Requests send fail: 0 Requests timeout: 0 Responses dropped: 0 Accepts received: 0 Rejects received: 0 ============================================================================= Server: 155.53.129.64 Port: 1813 Counter start time: Mar 12 20:50:57 2010 ----------------------------------------------------------------------------- Accounting Messages: ----------------------------------------------------------------------------- Requests sent: 0 Requests retried: 1 Requests send fail: 0 Requests timeout: 0 Responses dropped: 0 Accepts received: 1 Rejects received: 0 ============================================================================= Server: 1.1.1.1 Port: 3799 Counter start time: Mar 12 20:50:57 2010 ----------------------------------------------------------------------------- CoA Messages: ----------------------------------------------------------------------------- Requests received: 0 Duplicate request: 0 Response ACK: 0 Response NAK: 0 ============================================================================= Server: 1.1.1.2 Port: 3800 Counter start time: Mar 12 20:50:57 2010 ----------------------------------------------------------------------------- CoA Messages: ----------------------------------------------------------------------------- Requests received: 0 Duplicate request: 0 Response ACK: 0 Response NAK: 0 ============================================================================= Server: 1.1.1.3 Port: 3801 Counter start time: Mar 12 20:50:57 2010 ----------------------------------------------------------------------------- CoA Messages: ----------------------------------------------------------------------------- Requests received: 0 Duplicate request: 0
The following example displays RADIUS statistics including AAA route download information:
[local]Redback>show radius ststistics ============================================================================== Context: local ============================================================================== Authentication Servers: Requests send: 0 Requests re-send: 0 Request timeout: 0 Requests send fail: 0 Requests accepted: 0 Requests rejected: 0 Response dropped: 0 Req in process: 0 Req in waiting: 0 Req in high wait queue: 0 Req in low wait queue: 0 Server slots 0 Capacity: 0% Server marked dead: 0 Accounting Servers: Requests send: 0 Requests re-send: 0 Request timeout: 0 Requests send fail: 0 Requests accepted: 0 Requests rejected: 0 Response dropped: 0 Req in process: 0 Req in waiting: 0 Req in high wait queue: 0 Req in low wait queue: 0 Server slots 0 Capacity: 0% Server marked dead: 0 Route Download Servers: Requests send: 1335 Requests re-send: 0 Request timeout: 0 Requests send fail: 0 Requests accepted: 1334 Requests rejected: 1 Response dropped: 0 Req in process: 0 Req in waiting: 0 Req in high wait queue: 0 Req in low wait queue: 0 Server slots 256 Capacity: 0% Server marked dead: 0 CoA Servers: Requests received: 0 Duplicate requests: 0 Response ACK: 0 Response NAK: 0 Send Details: Subscriber authentication: Request send: 0 Request retransmit: 0 Response received: 0 Server busy: 0 Server not ready: 0 No server: 0 Server marked dead: 0 Bad attribute: 0 Socket error: 0 Send accept to AAAd: 0 Send reject to AAAd: 0 Send meth fail to AAAd: 0 Internal error: 0 Unknown attribute: 0 No route: 0 Authorization: Request send: 0 Request retransmit: 0 Response received: 0 Server busy: 0 Server not ready: 0 No server: 0 Server marked dead: 0 Bad attribute: 0 Socket error: 0 Send accept to AAAd: 0 Send reject to AAAd: 0 Send meth fail to AAAd: 0 Internal error: 0 Unknown attribute: 0 No route: 0 Subscriber accounting: Request send: 0 Request retransmit: 0 Response received: 0 Server busy: 0 Server not ready: 0 No server: 0 Server marked dead: 0 Bad attribute: 0 Socket error: 0 Accounting accepted: 0 Accounting timeout: 0 Internal error: 0 Unknown attribute: 0 No route: 0 L2tp accounting: Request send: 0 Request retransmit: 0 Response received: 0 Server busy: 0 Server not ready: 0 No server: 0 Server marked dead: 0 Bad attribute: 0 Socket error: 0 Accounting accepted: 0 Accounting timeout: 0 Internal error: 0 Unknown attribute: 0 No route: 0 Accounting On/Off: Request send: 0 Request retransmit: 0 Response received: 0 Server busy: 0 Server not ready: 0 No server: 0 Server marked dead: 0 Bad attribute: 0 Socket error: 0 Accounting accepted: 0 Accounting timeout: 0 Internal error: 0 Unknown attribute: 0 No route: 0 Event accounting: Request send: 0 Request retransmit: 0 Response received: 0 Server busy: 0 Server not ready: 0 No server: 0 Server marked dead: 0 Bad attribute: 0 Socket error: 0 Accounting accepted: 0 Accounting timeout: 0 Internal error: 0 Unknown attribute: 0 No route: 0 Route download: Request send: 1335 Request retransmit: 0 Response received: 1335 Server busy: 0 Server not ready: 0 No server: 0 Server marked dead: 0 Bad attribute: 0 Socket error: 0 Send accept to AAAd: 1334 Send reject to AAAd: 0 Send meth fail to AAAd: 0 Internal error: 0 Unknown attribute: 0 No route: 0 Receive Details: No match request: 0 No match server: 0 Invalid packet: 0 Bogus packet: 0 Dup response packet: 0 ------------------------------------------------------------------------------ Global radius statistics: Send Details: Subscriber authentication: Request send: 0 Request retransmit: 0 Response received: 0 Server busy: 0 Server not ready: 0 No server: 0 Server marked dead: 0 Bad attribute: 0 Socket error: 0 Send accept to AAAd: 0 Send reject to AAAd: 0 Send meth fail to AAAd: 0 Internal error: 0 Unknown attribute: 0 No route: 0 Authorization: Request send: 0 Request retransmit: 0 Response received: 0 Server busy: 0 Server not ready: 0 No server: 0 Server marked dead: 0 Bad attribute: 0 Socket error: 0 Send accept to AAAd: 0 Send reject to AAAd: 0 Send meth fail to AAAd: 0 Internal error: 0 Unknown attribute: 0 No route: 0 Subscriber accounting: Request send: 0 Request retransmit: 0 Response received: 0 Server busy: 0 Server not ready: 0 No server: 0 Server marked dead: 0 Bad attribute: 0 Socket error: 0 Accounting accepted: 0 Accounting timeout: 0 Internal error: 0 Unknown attribute: 0 No route: 0 L2tp accounting: Request send: 0 Request retransmit: 0 Response received: 0 Server busy: 0 Server not ready: 0 No server: 0 Server marked dead: 0 Bad attribute: 0 Socket error: 0 Accounting accepted: 0 Accounting timeout: 0 Internal error: 0 Unknown attribute: 0 No route: 0 Accounting On/Off: Request send: 0 Request retransmit: 0 Response received: 0 Server busy: 0 Server not ready: 0 No server: 0 Server marked dead: 0 Bad attribute: 0 Socket error: 0 Accounting accepted: 0 Accounting timeout: 0 Internal error: 0 Unknown attribute: 0 No route: 0 Event accounting: Request send: 0 Request retransmit: 0 Response received: 0 Server busy: 0 Server not ready: 0 No server: 0 Server marked dead: 0 Bad attribute: 0 Socket error: 0 Accounting accepted: 0 Accounting timeout: 0 Internal error: 0 Unknown attribute: 0 No route: 0 Route download: Request send: 0 Request retransmit: 0 Response received: 0 Server busy: 0 Server not ready: 0 No server: 0 Server marked dead: 0 Bad attribute: 0 Socket error: 0 Send accept to AAAd: 0 Send reject to AAAd: 0 Send meth fail to AAAd: 0 Internal error: 0 Unknown attribute: 0 No route: 0 Receive Details: No match request: 0 No match server: 0 Invalid packet: 0 Bogus packet: 0 Dup response packet: 0
1.5 show rate-limit card
show rate-limit card {all | slot} dhcp {counter | log}
1.5.1 Purpose
Displays dropped Dynamic Host Configuration Protocol (DHCP) packet information for one or more traffic cards.
1.5.2 Command Mode
all modes
1.5.3 Syntax Description
all |
Displays DHCP packet information for all traffic cards. |
slot |
Slot number of a specific traffic card. |
counter |
Displays the count of dropped DHCP packets for one or all traffic cards. |
log |
Displays the log messages for dropped DHCP packets for one or all traffic cards. |
1.5.4 Default
None
1.5.5 Usage Guidelines
Use the show rate-limit card command to display DHCP packet information for packets dropped because of rate limiting.
Use the counter keyword to display the count of dropped DHCP packets for one or all traffic cards.
Use the log keyword to display the log messages for dropped DHCP packets for one or all traffic cards.
- Note:
- This command always displays a slot number unless no active traffic cards are present. If the resolution of the IP address is the Ethernet management port, the output might display a slot number.
- Note:
- By default, most show commands (in any mode) display information for the current context only or, depending on the command syntax, for all contexts. If you are an administrator for the local context, you can insert the optional context ctx-name construct, preceding the show command, to view output for the specified context without entering that context. For more information about using the context ctx-name construct, see the context command description.
- Note:
- By appending a space followed by the pipe ( | ) character at the end of a show command, you can filter the output using a set of modifier keywords and arguments. For more information, see Modifying Output of show Commands in Using the CLI.
1.5.6 Examples
The following example displays the count of dropped DHCP packets for the traffic card in slot 1:
[local]Redback>show rate-limit card 1 dhcp counter Slot 1 Ingress: card rate-limit 1060236 packets
The following example displays the log messages for the traffic card in slot 1:
[local]Redback>show rate-limit card 1 dhcp log Slot 1 Ingress: current index: 103 000 src-ip-addr 2.1.1.2 src-mac-addr 00 00 03 00 03 00 circuit 1/3:1023:63/1/1/5 001 src-ip-addr 2.1.1.2 src-mac-addr 00 00 03 00 03 00 circuit 1/3:1023:63/1/1/5 002 src-ip-addr 2.1.1.2 src-mac-addr 00 00 03 00 03 00 circuit 1/3:1023:63/1/1/5 003 src-ip-addr 2.1.1.2 src-mac-addr 00 00 03 00 03 00 circuit 1/3:1023:63/1/1/5 004 src-ip-addr 2.1.1.2 src-mac-addr 00 00 03 00 03 00 circuit 1/3:1023:63/1/1/5 005 src-ip-addr 2.1.1.2 src-mac-addr 00 00 03 00 03 00 circuit 1/3:1023:63/1/1/5
1.6 show rcm
show rcm {memory | session}
1.6.1 Purpose
Displays Router Configuration Manager (RCM) information.
1.6.2 Command Mode
all configuration modes
1.6.3 Syntax Description
memory |
Displays RCM memory usage. |
session |
Displays RCM session information. |
1.6.4 Default
None
1.6.5 Usage Guidelines
Use the show rcm command to display RCM information.
- Note:
- By default, most show commands (in any mode) display information for the current context only or, depending on the command syntax, for all contexts. If you are an administrator for the local context, you can insert the optional context ctx-name construct before the show command to view output for the specified context without entering that context. For more information about the context ctx-name construct, see the context command description.
- Note:
- By appending a space followed by the pipe ( | ) character at the end of a show command, you can filter the output using a set of modifier keywords and arguments. For more information, see Modifying Output of show Commands in Using the CLI.
1.6.6 Examples
The following example displays output from the show rcm command with the memory keyword:
[local]Redback>show rcm memory
Displaying memory usage by RCM: Internal chunk memory : 125200 bytes Dynamically memory allocated by all : 13844 bytes Memory allocated for msg by RCM components : 0 bytes
The following example displays output from the show rcm command with the session keyword:
[local]Redback>show rcm session
CLI pid State Trans ID Waiting on ------------------------------------------------------------------- 13117 Not in transaction N/A None 13059 Not in transaction N/A None 12610 In transaction 3062 None
1.7 show redundancy
show redundancy
1.7.1 Purpose
Displays the state of the standby controller card and verifies whether it is ready to become active. It also displays AAA route information.
1.7.2 Command Mode
All modes
1.7.3 Syntax Description
This command has no keywords or arguments.
1.7.4 Default
None
1.7.5 Usage Guidelines
Use the show redundancy command to display the state of the standby controller card and to verify whether it is ready to become active.
- Note:
- The SmartEdge 100 router does not support this command; the chassis has only one controller carrier card.
- Note:
- By default, most show commands (in any mode) display information for the current context only or, depending on the command syntax, for all contexts. If you are an administrator for the local context, you can insert the optional context ctx-name construct, preceding the show command, to view output for the specified context without entering that context. For more information about using the context ctx-name construct, see the context command description.
- Note:
- By appending a space followed by the pipe ( | ) character at the end of a show command, you can filter the output using a set of modifier keywords and arguments. For more information, see Modifying Output of show Commands in Using the CLI.
1.7.6 Examples
The following example displays the state of the controller cards:
[local]Redback>show redundancy
--------------------------------- This XCRP is active --------------------------------- Firmware in sync? : YES Software Release in sync? : YES Database in sync? : YES Mate-to-Mate link up? : YES Standby Ready? : YES
If you have configured AAA route download, you will see AAA routes information when you issue the show redundancy command:
[local]Redback>show redundancy
--------------------------------- This XCRP is active --------------------------------- STANDBY XCRP READY? : YES VxWorks in sync? : YES Database in sync? : YES Software Release in sync? : YES Firmware in sync? : YES Mate-to-Mate link up? : YES ARP SUCCESS CSM SUCCESS ISM SUCCESS RDB SUCCESS SM AAA DSLline SUCCESS SM AAA RD Info SUCCESS SM AAA Routes SUCCESS SM AAA Session SUCCESS SM AAA Strings SUCCESS SM DOT1Q SUCCESS SM ISM2 SUCCESS SM LDP ADJ SUCCESS SM LDP CTX SUCCESS SM LDP PEER SUCCESS SM LM SUCCESS SM OSPF SUCCESS SM RCM SUCCESS SM RIB SUCCESS SM STATD SUCCESS
1.8 show release
show release
1.8.1 Purpose
Displays release and installation information for the software images currently installed on the system.
1.8.2 Command Mode
All modes
1.8.3 Syntax Description
This command has no keywords or arguments.
1.8.4 Default
None
1.8.5 Usage Guidelines
Use the show release command to display the release and installation information for the software images on the system and the partitions in which they are installed. The active image shows the software that is currently loaded in the system, and the alternate image shows the alternate image available on the system.
- Note:
- By default, most show commands (in any mode) display information for the current context only or, depending on the command syntax, for all contexts. If you are an administrator for the local context, you can insert the optional context ctx-name construct before the show command to view output for the specified context without entering that context. For more information about the context ctx-name construct, see the context command description.
- Note:
- By appending a space followed by the pipe ( | ) character at the end of a show command, you can filter the output using a set of modifier keywords and arguments. For more information, see Modifying Output of show Commands in Using the CLI.
1.8.6 Examples
The following example displays the release and installation information for the installed software images:
[local]Redback>show release
Installed releases: p02: active (will be booted after next reload) ---------------------------------------------- Version SEOS-5.0.5-Release Built on Mon Jan 02 10:00:01 PST 2006 Copyright (C) 1998-2006, Redback Networks Inc. All rights reserved. p01: alternate -------------- Version SEOS-5.0.5-Release Built on Mon Jan 16 10:00:01 PDT 2006 Copyright (C) 1998-2006, Redback Networks Inc. All rights reserved.
1.9 show rip debug
show rip debug
1.9.1 Purpose
Displays enabled Routing Information Protocol (RIP) debug settings.
1.9.2 Command Mode
all modes
1.9.3 Syntax Description
This command has no keywords or arguments.
1.9.4 Default
None
1.9.5 Usage Guidelines
Use the show rip debug command to display enabled RIP debug settings.
- Note:
- By default, most show commands (in any mode) display information for the current context only or, depending on the command syntax, for all contexts. If you are an administrator for the local context, you can insert the optional context ctx-name construct, preceding the show command, to view output for the specified context without entering that context. For more information about using the context ctx-name construct, see the context command description.
- Note:
- By appending a space followed by the pipe ( | ) character at the end of a show command, you can filter the output using a set of modifier keywords and arguments. For more information, see Modifying Output of show Commands in Using the CLI.
1.9.6 Examples
The following example displays output from the show rip debug command:
[local]Redback>show rip debug
RIP debug flags: REQUEST_RECV REQUEST_SEND RESPONSE_RECV RESPONSE_SEND PACKET_GENERAL RIP debug detail flags:
1.10 show rip instance
1.10.1 Purpose
Displays information for all Routing Information Protocol (RIP) instances, or only for a particular RIP instance.
1.10.2 Command Mode
all modes
1.10.3 Syntax Description
instance |
Optional. RIP instance name. |
1.10.4 Default
When entered without the optional instance argument, this command displays information for all configured RIP instances.
1.10.5 Usage Guidelines
Use the show rip instance command to display information for all RIP instances, or only for a particular RIP instance.
- Note:
- By default, most show commands (in any mode) display information for the current context only or, depending on the command syntax, for all contexts. If you are an administrator for the local context, you can insert the optional context ctx-name construct, preceding the show command, to view output for the specified context without entering that context. For more information about using the context ctx-name construct, see the context command description.
- Note:
- By appending a space followed by the pipe ( | ) character at the end of a show command, you can filter the output using a set of modifier keywords and arguments. For more information, see Modifying Output of show Commands in Using the CLI.
1.10.6 Examples
The following example displays output from the show rip instance command:
[local]Redback>show rip instance
Fl - Instance Flags: (O - Default information originate), P - Maximum paths TH - Flash update threshold, DM - Default metric, Dis - Admin distance Dl - Output delay, TableVer - Routing table version, Upd - Update Inv - Invalid, Hld - Holddown, Flu - Flush, Expr - Next flashupdate GblFlg - Global flags: (I - ISM up, P - RPM up, R-RIB up) InstanceName Fl P TH DM Dis Dl TableVer Expr Upd/Inv/Hld/Flu GblFlg area1 - 8 5 0 120 0 1 2 30 180 180 240 IPR area2 - 8 5 0 120 0 1 2 30 180 180 240 IPR
1.11 show rip interface
1.11.1 Purpose
Displays information for all Routing Information Protocol (RIP) interfaces, or only for RIP interfaces within a particular RIP instance.
1.11.2 Command Mode
all modes
1.11.3 Syntax Description
instance |
Optional. RIP instance name. |
1.11.4 Default
When entered without the optional instance argument, this command displays information about all RIP interfaces.
1.11.5 Usage Guidelines
Use the show rip interface to display information for all RIP interfaces, or only for RIP interfaces within a particular RIP instance.
- Note:
- By default, most show commands (in any mode) display information for the current context only or, depending on the command syntax, for all contexts. If you are an administrator for the local context, you can insert the optional context ctx-name construct, preceding the show command, to view output for the specified context without entering that context. For more information about using the context ctx-name construct, see the context command description.
- Note:
- By appending a space followed by the pipe ( | ) character at the end of a show command, you can filter the output using a set of modifier keywords and arguments. For more information, see Modifying Output of show Commands in Using the CLI.
1.11.6 Examples
The following example displays output from the show rip interface command:
[local]Redback>show rip interface
Interface Flags: U - Up, B - Bound, L - Listen, S - Supply, A-Admin up V - have Valid addr, R-Registered with ISM, O - Default information originate N - No default info orig, H - split Horizon, P - Poison reverse, Upd - Update Inv - Invalid, Hld - Holddown, FLu - Flush, Expr - Next full update, Co - Cost Interfaces of RIP instance: area1 Name Addr/MaskLen State Upd/Inv/Hld/Flu Expr Co IntfId ripint1 10.1.1.1/24 LSRVH 30 180 180 240 29 1 10000001 Total 1 interfaces, 0 are up.
1.12 show ripng
show ripng {all-instances | debug | instance [instance-id] | interface [if-name] | route [instance-id]}
1.12.1 Purpose
Displays Routing Information Protocol next generation (RIPng) information.
1.12.2 Command Mode
all modes
1.12.3 Syntax Description
all-instances |
Displays information for all RIPng instances. |
debug |
Displays RIPng debug settings. |
instance |
Displays RIPng instance information. |
instance-id |
Optional. Instance ID. When specified, displays RIPng instance or RIPng route information for a specific RIPng instance. |
interface |
Displays RIPng interface information. |
if-name |
Optional. Interface name. When specified, displays information for a specific RIPng interface. |
route |
Displays RIPng route information. |
1.12.4 Default
None
1.12.5 Usage Guidelines
Use the show ripng command to display RIPng information.
- Note:
- By default, most show commands (in any mode) display information for the current context only or, depending on the command syntax, for all contexts. If you are an administrator for the local context, you can insert the optional context ctx-name construct, preceding the show command, to view output for the specified context without entering that context. For more information about using the context ctx-name construct, see the context command description.
- Note:
- By appending a space followed by the pipe ( | ) character at the end of a show command, you can filter the output using a set of modifier keywords and arguments. For more information, see Modifying Output of show Commands in Using the CLI.
1.12.6 Examples
The following example displays information for all RIPng instances:
[local]Redback>show ripng all-instances Fl - Flags: (O - Default information originate, M - Maximum routes reached) P - Maximum paths TH - Flash update threshold, DM - Default metric, Dis - Admin distance Dl - Output delay, TableVer - Routing table version, Upd - Update Inv - Invalid, Hld - Holddown, Flu - Flush, Expr - Next flashupdate InstanceName Fl P TH DM Dis Dl TableVer Expr Upd/Inv/Hld/Flu #Route Context local: 1 - 16 5 0 120 0 4 1 30 180 180 240 3
The following example displays the RIPng debug settings:
[local]Redback>show ripng debug RIP debug flags: REQUEST_RECV REQUEST_SEND RESPONSE_RECV RESPONSE_SEND PACKET_GE NERAL MEMORY INTERNAL PROTOCOL IPC TIMER INTERFACE LOCAL_RIB GLOBAL_RIB POLICY C ONFIG IN_QUEUE OUT_QUEUE AUTHENTICATION THREAD SOCKIO ISM GENERAL RIP debug detail flags:
The following example displays information for the RIPng instance, 4:
[local]Redback>show ripng instance 4 Fl - Flags: (O - Default information originate, M - Maximum routes reached) P - Maximum paths TH - Flash update threshold, DM - Default metric, Dis - Admin distance Dl - Output delay, TableVer - Routing table version, Upd - Update Inv - Invalid, Hld - Holddown, Flu - Flush, Expr - Next flashupdate InstanceName Fl P TH DM Dis Dl TableVer Expr Upd/Inv/Hld/Flu #Route Context local: 1 - 16 5 0 120 0 4 3 30 180 180 240 3
The following example displays information for the RIPng interface, 88:
[local]Redback>show ripng interface 88 Interface Flags: U - Up, B - Bound, L - Listen, S - Supply, A-Admin up V - have Valid addr, R-Registered with ISM, O - Default information originate N - No default info orig, H - split Horizon, P - Poison reverse, Upd - Update Inv - Invalid, Hld - Holddown, FLu - Flush, Expr - Next full update, Co - Cost Interfaces of RIP instance: 1 Name Addr/MaskLen State Upd/Inv/Hld/Flu Expr Co IntfId lo 8001::1/128 ULVH 30 180 180 240 16 1 10000004 to-nbor 7001::1/112 ULSVH 30 180 180 240 16 1 10000003 Total 2 interfaces, 2 are up.
The following example displays information for the RIPng route, 37:
[local]Redback>show ripng route 37 T - RouteType:(C - Connected, E - External, R - RIP, EB - External backup) M - Metric, Exp - Expire time, PrFl - Prefix flags ( D - Delete, H - Holddown A - Need flash, B - Need download to RIB, I - Inactive) NhFl - Next Hop Flags (W - Withdrawn from RIB, H - Holddown, F - Flush expire before holddown) Routing table for RIP instance: 1 T Prefix/PrefixLen NextHop M Exp PrFl|NhFl Intf Peer C 7001::/112 :: 0 - 6|6 to-nbor C 8001::1/128 :: 0 - 6|6 lo R 8001::2/128 fe80::230:88ff:fe00:3294 1 172 6|6 to-nbor Total 3 prefixes 3 routes(1 intern 0 extern 2 connected)
1.13 show rip route
1.13.1 Purpose
Displays information about all Routing Information Protocol (RIP) routes, or only for routes within a particular RIP instance.
1.13.2 Command Mode
all modes
1.13.3 Syntax Description
instance |
Optional. RIP instance name. |
ip-addr/prefix-length |
Optional. IP address (in the form A.B.C.D) and prefix length, separated by the slash (/) character. The range of values for the prefix-length argument is 0 to 32. |
longer-prefixes |
Optional. Displays all routes that fall into the range of the prefix; otherwise, only routes that exactly match are displayed. |
1.13.4 Default
When entered without any optional arguments, this command displays information about all RIP routes.
1.13.5 Usage Guidelines
Use the show rip route command to display information about RIP routes, or only for routes within a particular RIP instance.
- Note:
- By default, most show commands (in any mode) display information for the current context only or, depending on the command syntax, for all contexts. If you are an administrator for the local context, you can insert the optional context ctx-name construct, preceding the show command, to view output for the specified context without entering that context. For more information about using the context ctx-name construct, see the context command description.
- Note:
- By appending a space followed by the pipe ( | ) character at the end of a show command, you can filter the output using a set of modifier keywords and arguments. For more information, see Modifying Output of show Commands in Using the CLI.
1.13.6 Examples
The following example displays output from the show rip route command:
[local]Redback>show rip route
T - RouteType: (C - Connected, E - External, R - RIP, EB - External backup) M - Metric, Exp - Expire time, PrFl - Prefix flags D - Delete, H - Holddown A - Need flash, B - Need download to RIB, I - Inactive) NhFl - Next Hop Flags (W - Withdrawn from RIB, H - Holddown, F - Flush expire before holddown) Routing table for RIP instance: rip001 T Prefix NextHop M Exp PrFl|NhFl Intf Peer Total 0 prefixes 0 routes (0 intern 0 extern 0 connected)
1.14 show rmon
show rmon {alarms | events}
1.14.1 Purpose
Displays Remote Monitoring (RMON) information.
1.14.2 Command Mode
All modes
1.14.3 Syntax Description
alarms |
Displays RMON alarm records. |
events |
Displays RMON event records. |
1.14.4 Default
None
1.14.5 Usage Guidelines
Use the show rmon command to display RMON information.
- Note:
- By default, most show commands (in any mode) display information for the current context only or, depending on the command syntax, for all contexts. If you are an administrator for the local context, you can insert the optional context ctx-name construct before the show command to view output for the specified context without entering that context. For more information about the context ctx-name construct, see the context command description.
- Note:
- By appending a space followed by the pipe ( | ) character at the end of a show command, you can filter the output using a set of modifier keywords and arguments. For more information, see Modifying Output of show Commands in Using the CLI.
1.14.6 Examples
The following example displays RMON alarms:
[local]Redback>show rmon alarm
rmon alarm 5 ipInReceives.0 50 delta rising-threshold 5000 5 falling-threshold 200 6 owner "gold.isp.net" rmon alarm 10 ipForwDatagrams.0 60 delta rising-threshold 3000000 1 falling-threshold 600000 2 rmon alarm 20 rbnCpuMeterOneMinuteAvg.0 5 absolute rising-threshold 50 3 falling-threshold 10 4 owner "alarmDel6"
The following example displays RMON events:
[local]Redback>show rmon events
rmon event 1 log notify owner gold.isp.net description "packets per second too high in context gold.isp.net" rmon event 2 log notify owner gold.isp.net description "packets per second is below 10000 in context gold.isp.net" rmon event 3 log notify owner gold.isp.net description "One minute average CPU usage on the device is above 50%" rmon event 4 log notify owner gold.isp.net description "One minute average CPU usage on the device is now below 10%" rmon event 5 log notify owner gold.isp.net description "The total number of input IP datagrams received from interfaces per second is 100 and above" rmon event 6 log notify owner gold.isp.net description "The total number of input IP datagrams received from interfaces per second is 4 and below"
1.15 show route-map
show route-map [map-name] [summary]
1.15.1 Purpose
Displays information about configured route maps.
1.15.2 Command Mode
all modes
1.15.3 Syntax Description
map-name |
Optional. Name of the route map. |
summary |
Optional. Displays route map summary information. |
1.15.4 Default
Displays all configured route maps.
1.15.5 Usage Guidelines
Use the show route-map command to display information about configured route maps.
- Note:
- By default, most show commands (in any mode) display information for the current context only or, depending on the command syntax, for all contexts. If you are an administrator for the local context, you can insert the optional context ctx-name construct, preceding the show command, to view output for the specified context without entering that context. For more information about using the context ctx-name construct, see the context command description.
- Note:
- By appending a space followed by the pipe ( | ) character at the end of a show command, you can filter the output using a set of modifier keywords and arguments. For more information, see Modifying Output of show Commands in Using the CLI.
1.15.6 Examples
The following example displays all configured route maps:
[local]Redback>show route-map route-map c1-a2-in: count: 6, sequences: 10 - 40, client count: 1 modified: 2 day(s), 21 hour(s) ago sequence 10, permit (hits: 13, cache hits: 7) Match clauses: as-path (as-path filter): AS2686 Set clauses: local-preference 80 weight 65535 sequence 15, permit (hits: 17667, cache hits: 17667) Match clauses: ip address (prefix list): /22-permit Set clauses: community local-AS sequence 20, permit (hits: 2, cache hits: 0) Match clauses: ip address (prefix list): slash9 Set clauses: metric 80 sequence 25, permit (hits: 3, cache hits: 0) Match clauses: ip address (prefix list): slash18 Set clauses: community-list no-export/11:121-delete delete community 11:102 additive ip next-hop 10.255.255.254 sequence 30, permit (hits: 307062, cache hits: 0) Match clauses: community (community list filter): 11:121-c1-wtn Set clauses: community 11:102 additive sequence 40, permit (hits: 0, cache hits: 0) Match clauses: Set clauses: route-map a2-out-map: count: 4, sequences: 10 - 40, client count: 1 modified: 2 day(s), 21 hour(s) ago sequence 40, permit (hits: 2227, cache hits: 0) Match clauses: community (community list filter): a2community Set clauses: metric-type internal total route maps: 2
The following command displays a summary of all configured route maps:
[local]Redback>show route-map summary route-map c1-a2-in: count: 6, sequences: 10 - 40, client count: 1 modified: 2 day(s), 21 hour(s) ago route-map a2-out-map: count: 4, sequences: 10 - 40, client count: 1 modified: 2 day(s), 21 hour(s) ago total route maps: 2
1.16 show rsvp counters
show rsvp counters [global | lsp | packets]
1.16.1 Purpose
Displays Resource Reservation Protocol (RSVP) counter information.
1.16.2 Command Mode
All modes
1.16.3 Syntax Description
global |
Optional. Displays only global counters. |
lsp |
Optional. Displays only label-switched path (LSP) related counters. |
packets |
Optional. Displays only packet-related counters. |
1.16.4 Default
Displays all RSVP counter information.
1.16.5 Usage Guidelines
Use the show rsvp counters command to display RSVP counter information.
- Note:
- By default, most show commands (in any mode) display information for the current context only or, depending on the command syntax, for all contexts. If you are an administrator for the local context, you can insert the optional context ctx-name construct, preceding the show command, to view output for the specified context without entering that context. For more information about using the context ctx-name construct, see the context command description.
- Note:
- By appending a space followed by the pipe ( | ) character at the end of a show command, you can filter the output using a set of modifier keywords and arguments. For more information, see Modifying Output of show Commands in Using the CLI.
1.16.6 Examples
The following example displays packet-related output from the show rsvp counters command:
[local]Redback>show rsvp counters packets
--- Global RSVP Counters --- Packet Counters Interval: 00:00:09 Packets Sent: 0 Packets Recvd: 0 Packets Tx dropped: 0 Packets Rx dropped: 0 Packets Tx IO errs: 0 Packets Rx IO errs: 0 PATH Sent: 0 PATH Recvd: 0 RESV Sent: 0 RESV Recvd: 0 PATH TEAR Sent: 0 PATH TEAR Recvd: 0 RESV TEAR Sent: 0 RESV TEAR Recvd: 0 PATH ERR Sent: 0 PATH ERR Recvd: 0 RESV ERR Sent: 0 RESV ERR Recvd: 0 CONFIRM Sent: 0 CONFIRM Recvd: 0 Unknown Pkts Recvd: 0
The following example displays LSP-related output from the show rsvp counters command:
[local]Redback>show rsvp counters lsp
--- Global RSVP Counters --- LSP Counters Total Sessions: 26 Total LSPs: 27 Ingress LSPs: 7 Egress LSPs: 18 Transit LSPs: 2 Backup LSPs: 1 Up LSPs: 23 Down LSPs: 4 Active LSPs: 23 Backup2 LSPs: 0 Bypass LSPs: 0 Rerouted LSPs: 0 Stale LSPs: 5 Stale LSPs Recovered: 5
In this example:
Stale LSPs are the number of LSPs that moved to the Stale state due to local or neighbor restart events.
Stale LSPs Recovered are the number of previously stale LSPs that moved back successfully to the Up state.
1.17 show rsvp debug
show rsvp debug
1.17.1 Purpose
Displays Resource Reservation Protocol (RSVP) debug information.
1.17.2 Command Mode
all modes
1.17.3 Syntax Description
This command has no keywords or arguments.
1.17.4 Default
None
1.17.5 Usage Guidelines
Use the show rsvp debug command to display RSVP debug information.
- Note:
- By default, most show commands (in any mode) display information for the current context only or, depending on the command syntax, for all contexts. If you are an administrator for the local context, you can insert the optional context ctx-name construct, preceding the show command, to view output for the specified context without entering that context. For more information about using the context ctx-name construct, see the context command description.
- Note:
- By appending a space followed by the pipe ( | ) character at the end of a show command, you can filter the output using a set of modifier keywords and arguments. For more information, see Modifying Output of show Commands in Using the CLI.
1.17.6 Examples
The following example displays output from the show rsvp debug command:
[local]Redback>show rsvp debug
Event Filter Packet Packet Send Path Send Path Recv Resv Send Resv Recv Path Error Send Path Error Recv Resv Error Send Resv Error Recv Path Tear Send Path Tear Recv Packet Confirm Send Packet Confirm Recv Packet Recv
1.18 show rsvp explicit-route
show rsvp explicit-route [er-name] [detail]
1.18.1 Purpose
Displays explicit route information.
1.18.2 Command Mode
all modes
1.18.3 Syntax Description
er-name |
Optional. Name of the explicit route for which information is displayed. |
detail |
Optional. Displays detailed information for the specified explicit route or all explicit routes. |
1.18.4 Default
Displays summary information for all explicit routes.
1.18.5 Usage Guidelines
Use the show rsvp explicit-route command to display explicit route information.
Use the er-name argument to display detailed information for a specific explicit route.
Use the detail keyword to display the detailed explicit route information; otherwise, the summary information is displayed.
- Note:
- By default, most show commands (in any mode) display information for the current context only or, depending on the command syntax, for all contexts. If you are an administrator for the local context, you can insert the optional context ctx-name construct, preceding the show command, to view output for the specified context without entering that context. For more information about using the context ctx-name construct, see the context command description.
- Note:
- By appending a space followed by the pipe ( | ) character at the end of a show command, you can filter the output using a set of modifier keywords and arguments. For more information, see Modifying Output of show Commands in Using the CLI.
1.18.6 Examples
The following example displays summary information for all explicit routes:
[local]Redback>show rsvp explicit-route Explicit Route Hop Count exp-rt1 2
The following example displays detailed information for the exp-rt1 explicit route:
[local]Redback>show rsvp explicit-route exp-rt1 Explicit Route: exp-rt1 Hop Count: 2 Length: 8 Addr: 10.1.1.1/32 Length: 8 Addr: 10.2.1.2/32
1.19 show rsvp interface
show rsvp interface [if-name | detail]
1.19.1 Purpose
Displays Resource Reservation Protocol (RSVP) interface summary information.
1.19.2 Command Mode
all modes
1.19.3 Syntax Description
if-name |
Optional. Name of the RSVP interface to be displayed. |
detail |
Optional. Displays detailed information. |
1.19.4 Default
Displays all RSVP interface summary information.
1.19.5 Usage Guidelines
Use the show rsvp interface command to display all RSVP interface summary information.
Use the if-name argument to display information for only a specific RSVP interface.
Use the detail keyword to display detailed RSVP interface information; otherwise, summary information is displayed.
- Note:
- By default, most show commands (in any mode) display information for the current context only or, depending on the command syntax, for all contexts. If you are an administrator for the local context, you can insert the optional context ctx-name construct, preceding the show command, to view output for the specified context without entering that context. For more information about using the context ctx-name construct, see the context command description.
- Note:
- By appending a space followed by the pipe ( | ) character at the end of a show command, you can filter the output using a set of modifier keywords and arguments. For more information, see Modifying Output of show Commands in Using the CLI.
1.19.6 Examples
The following example shows how to display information for all configured RSVP interfaces:
[local]Redback>show rsvp interface
--- All RSVP Interfaces --- Address/Mask Name State Bound to 1.1.1.1/24 one Up 7/4 3.1.1.1/24 two Up 7/2
The following example shows how to display information for the IPst.14 RSVP interface:
[local]router#show rsvp interface IPst.14 --- RSVP Interface 10.18.241.74 --- Name : IPst.14 Mask : 255.255.255.252 State : Down Bound to : Refresh Interval (sec) : 30 Keep Multiplier : 6 Hello Interval (sec) : 0 Hello Keep Multiplier : 3 Max Bandwidth (By/sec) : 0 TE metric : Use IGP metric TE update threshold : 5 TE advertisements : 0 Tracking : Enabled (tracking objects below) Track-mtu Allocated BW (By/sec) : 0 Priority Resv B/W (By/sec) Last-Advertised Available 0 0 0 0 1 0 0 0 2 0 0 0 3 0 0 0 4 0 0 0 5 0 0 0 6 0 0 0 7 0 0 0
1.20 show rsvp lsp
show rsvp lsp [lsp-name backup | bypass | detail | down | egress | ingress | label | protected | protection | track [lsp-name | detail] | transit | up]
1.20.1 Purpose
Displays Resource Reservation Protocol (RSVP) label-switched path (LSP) information.
1.20.2 Command Mode
all modes
1.20.3 Syntax Description
lsp-name |
Optional. Name of LSP for which information is displayed. |
backup |
Optional. Displays only back-up LSPs. |
bypass |
Optional. Displays only bypass LSPs. |
detail |
Optional. Displays detailed information. |
down |
Optional. Displays only down LSPs. |
egress |
Optional. Displays only egress LSPs. |
ingress |
Optional. Displays only ingress LSPs. |
label |
Optional. Displays label information for RSVP LSPs. |
protection |
Optional. Displays only protection information. |
protected |
Optional. Displays only protected LSPs with back-ups configured. |
transit |
Optional. Displays only transit LSPs. |
track |
Optional. Displays information about the tracking-enabled label-switched paths (LSPs) that are currently configured on your system. Include the lsp-name argument after the track keyword to display tracking information for a specific LSP. Include the detail keyword after the track keyword to display detailed tracking information for a specific LSP. |
up |
Optional. Displays only up LSPs. |
1.20.4 Default
Displays summary information for all LSPs.
1.20.5 Usage Guidelines
Use the show rsvp lsp command to display all RSVP LSP information.
Use the lsp-name argument to display information only for the specified LSP, or use any of the available keywords to display LSP information only for the specified keyword.
- Note:
- By default, most show commands (in any mode) display information for the current context only or, depending on the command syntax, for all contexts. If you are an administrator for the local context, you can insert the optional context ctx-name construct, preceding the show command, to view output for the specified context without entering that context. For more information about using the context ctx-name construct, see the context command description.
- Note:
- By appending a space followed by the pipe ( | ) character at the end of a show command, you can filter the output using a set of modifier keywords and arguments. For more information, see Modifying Output of show Commands in Using the CLI.
- Note:
- When the output fills a width of 80 characters or more, the column headings and contents are truncated or abbreviated.
- Note:
- This output fills a width of 80 characters, and that is why the column headings, as well the contents, have been truncated or abbreviated.
1.20.6 Examples
The following example displays information for all RSVP LSPs:
[local]Redback>show rsvp lsp
RSVP LSPs LSP ID Ingress Endpoint State FRR Origin Protection W-E-bkup 1 10.1.1.2 10.2.1.2 Up Ingress Backup W-E-lsp 1 10.1.1.2 10.2.1.2 Shut Ingress Primary E-W-lsp 2 10.2.1.2 10.1.1.2 Up Egress None
The show rsvp lsp command displays the following:
- LSP—Name of the LSP. Each RSVP LSP has a specific name.
- ID—Tunnel ID of the LSP (this ID is determined by the ingress node of the LSP).
- Ingress—IP address of the ingress of the LSP. Usually, this address is the IP address of the router from which the packet got its LSP, but the ingress address is configurable for SE RSVP LSPs; so, it can also be a loopback address.
- Endpoint—Destination address of the LSP. Usually, this address is the IP address of the destination router to which the packet has its last hop, but the address does not need to be the router ID of the destination router; it can be a loopback address configured at the destination router.
- State—State of the LSP. The state can be Up, Down, Shut, or Stale.
- FRR—If the LSP has an FRR bypass LSP that can protect it, then this field displays the tunnel ID of the bypass LSP that is protecting it. Otherwise, this field is empty.
- 0rigin—Origin, for the type of LSP relative to the location of the local switch in the path: I (or Ingress) for ingress, E (or Egress) for egress, or T (or Transit) for transit.
- Protection—Protection characteristic of the LSP. For example, if an LSP does not protect other LSPs but is protected by other LSPs, Prim (for primary LSP) is listed. If an LSP protects other LSPs (a backup or backup of a backup), Back is listed. If an LSP has no protection characteristic, None is listed. If an LSP is a bypass LSP, it is preestablished to protect an LSP that traverses either a specific link (link bypass LSP) or node (node bypass LSP), and Bypas is listed.
The following example displays information for RSVP LSPs that are currently shut down:
[local]Redback>show rsvp lsp down
RSVP LSPs LSP ID Ingress Endpoint State FRR Origin Protection W-E-lsp 1 10.1.1.2 10.2.1.2 Shut Ingress None
The following example displays information for RSVP LSPs that are currently up:
[local]Redback>show rsvp lsp up
RSVP LSPs LSP ID Ingress Endpoint State FRR Origin Protection W-E-bkup 1 10.1.1.2 10.2.1.2 Up Ingress Backup E-W-lsp 2 10.2.1.2 10.1.1.2 Up Egress None
The following example displays information for egress RSVP LSPs:
[local]Redback>show rsvp lsp egress
RSVP LSPs LSP ID Ingress Endpoint State FRR Origin Protection E-W-lsp 2 10.2.1.2 10.1.1.2 Up Egress None
The following example displays information for ingress RSVP LSPs:
[local]Redback>show rsvp lsp ingress LSP TID Ingress Endpoint State FRR O Prtct R1-R5-backup 1 10.2.250.201 10.2.250.205 Up I Back R1-R5-prim 1 10.2.250.201 10.2.250.205 Up 8 I Prim R1-R6-backup 3 10.2.250.201 10.2.250.206 Up I Back R1-R6-prim 3 10.2.250.201 10.2.250.206 Up 7 I Prim R1-R3-bypass 4 10.2.250.201 10.2.250.203 Up I Bypas R1-R2-prim 6 10.2.250.201 10.2.250.202 Up 7 I None R1-R2-bypass 7 10.2.250.201 10.2.250.202 Up I Bypas R1-R5-bypass-node-R3 8 10.2.250.201 10.2.250.205 Up I Bypas R1-R3-prim 9 10.2.250.201 10.2.250.203 Up 4 I None R1-R4-prim 10 10.2.250.201 10.2.250.204 Up 7 I None
This example shows information on incoming packet in the local MPLS-enabled network where RSVP is used to communicate labels and their meaning among label-switched routers (LSRs). At each incoming (ingress) point of the network, packets are assigned a label by an edge label-switched router (LSR). Packets are forwarded along a label-switched path (LSP) where each LSR makes forwarding decisions based on the label information. At each hop, the LSR swaps the existing label for a new label that tells the next hop how to forward the packet. At the outgoing (egress) point, an edge LSR removes the label, and forwards the packet to its destination.
The show rsvp lsp ingress command displays the following:
- LSP—The name of the LSP. All RSVP LSPs have a specific name.
- TID—The Tunnel ID. It is unique per originating node, for a given LSP, so the ID can be 1 to 40,000.
- Ingress—The IP address of the ingress of the LSP. Usually, this is the IP address of the router that the packet got its LSP from, but the ingress address is configurable for SE RSVP LSPs, so it can also be a loopback address.
- Endpoint—The destination address of the LSP. Usually, this is the IP address of the destination router that the packet has its last hop to, but the address does not need to be the destination router's router ID, it can be a loopback address configured at the destination router.
- State—The state of the LSP. The state can be Up, Down, Shut, or Stale.
- FRR—If the LSP has a Fast-Reroute (FRR) bypass LSP that can protect it, then this field displays the tunnel ID of the bypass LSP that is protecting it. Otherwise, this field is empty.
- 0—Origin, for the type of LSP with regards to where the local switch is in the path: I for ingress, E for egress, or T for transit.
- Prtct—The protection characteristic of the LSP. For example, if it is an LSP that does not protect other LSPs but is protected by other LSPs, Prim (for primary LSP) is listed. If it is an LSP that protects other LSPs (a backup or backup of a backup), Back is listed. If it has no protection characteristic, None is listed. If it is a bypass LSP, it is preestablished to protect an LSP that traverses either a specific link (link bypass LSP) or node (node bypass LSP), and Bypas is listed.
The following example displays label information for all RSVP LSPs:
[local]Redback>show rsvp lsp label
LSP State Upstream lbl Downstream lbl W-E-bkup Up N/A 262144 W-E-lsp Shut N/A 0 E-W-lsp Up 3 N/A
The following example displays information for RSVP LSPs protected with a backup LSP:
[local]Redback>show rsvp lsp protected
LSP ID Ingress Endpoint State Backed up by W-E-lsp 1 10.1.1.2 10.2.1.2 Shut W-E-bkup
The following example displays protection information for all RSVP LSPs:
[local]Redback>show rsvp lsp protection
Primary State Active Backup State Active W-E-lsp Shut No W-E-bkup Up Yes
The following example displays information for transmit RSVP LSPs:
[local]Redback>show rsvp lsp transit
RSVP LSPs LSP ID Ingress Endpoint State FRR Origin Protection W-E-bkup 1 10.1.1.2 10.2.1.2 Up Transit None E-W-lsp 2 10.2.1.2 10.1.1.2 Up Transit None
The following example shows how to display summary information about all tracking-enabled LSPs currently configured on the router:
[local]Redback#show rsvp lsp track
LSP TID Ingress Endpoint State FRR O Prtct AC1_MTU1_azul 13 10.18.241.3 10.18.241.6 Down (tracking) I None AC1_AC2_rojo 22 10.18.241.3 10.18.241.4 Down (tracking) I Prim
The following example shows how to display information about the AC1_MTU1_azul tracking-enabled LSP:
[local]Redback#show rsvp lsp track AC1_MTU1_azul --- RSVP LSP AC1_MTU1_azul (Tunnel ID: 13) --- Ingress : 10.18.241.3 Endpoint : 10.18.241.6 Origin : Ingress LSP State : Down (tracking) Extended Tunnel ID : 10.18.241.3 LSP ID : 1 Traffic-Eng : default State Transitions : 2 Downstream Nhop : 0.0.0.0 Downstream Intf : 0.0.0.0 Downstream Intf Name: Downstream Nbr : 0.0.0.0 Downstream Label : 0 Setup Priority : 7 Holding Priority : 0 Last Downstream Tx : 58761 Last Downstream Rx : 0 Next Timer in (sec) : 1271218063 Lifetime (sec) : 0 Time to Die (sec) : 0 B/W (Bytes/sec) : 0 LSP cct : Cct invalid IGP Shortcut : Disabled Session Attr : Local-Protect Node-Protect May-Reroute Record-Label Use CSPF Route : Yes Record Route : Yes Dynamic Route : Tracking : Track-mtu Tracking State : Down CSPF Route : Pending
The following example shows how to display detailed information about all tracking-enabled LSPs currently configured on the router:
[local]Redback#show rsvp lsp track detail --- RSVP LSP AC1_MTU1_azul (Tunnel ID: 13) --- Ingress : 10.18.241.3 Endpoint : 10.18.241.6 Origin : Ingress LSP State : Down (tracking) Extended Tunnel ID : 10.18.241.3 LSP ID : 1 Traffic-Eng : default State Transitions : 2 Downstream Nhop : 0.0.0.0 Downstream Intf : 0.0.0.0 Downstream Intf Name: Downstream Nbr : 0.0.0.0 Downstream Label : 0 Setup Priority : 7 Holding Priority : 0 Last Downstream Tx : 59130 Last Downstream Rx : 0 Next Timer in (sec) : 1271217694 Lifetime (sec) : 0 Time to Die (sec) : 0 B/W (Bytes/sec) : 0 LSP cct : Cct invalid IGP Shortcut : Disabled Session Attr : Local-Protect Node-Protect May-Reroute Record-Label Use CSPF Route : Yes Record Route : Yes Dynamic Route : Tracking : Track-mtu Tracking State : Down CSPF Route : Pending --- RSVP LSP AC1_AC2_rojo (Tunnel ID: 22) --- Ingress : 10.18.241.3 Endpoint : 10.18.241.4 Origin : Ingress LSP State : Down (tracking) Extended Tunnel ID : 10.18.241.3 LSP ID : 1 Traffic-Eng : default State Transitions : 2 Downstream Nhop : 0.0.0.0 Downstream Intf : 0.0.0.0 Downstream Intf Name: Downstream Nbr : 0.0.0.0 Downstream Label : 0 Setup Priority : 7 Holding Priority : 0 Last Downstream Tx : 59764 Last Downstream Rx : 0 Next Timer in (sec) : 1271217694 Lifetime (sec) : 0 Time to Die (sec) : 0 B/W (Bytes/sec) : 0 LSP cct : Cct invalid IGP Shortcut : Disabled Session Attr : Local-Protect Node-Protect May-Reroute Record-Label Use CSPF Route : Yes Record Route : Yes Dynamic Route : LSP protected by LSP AC1_AC2_verde which is protected by LSP AC1_AC2_3camino Tracking : Track-mtu Tracking State : Down CSPF Route : Pending (21 retries)
1.21 show rsvp neighbor
show rsvp neighbor [ip-addr | detail]
1.21.1 Purpose
Displays Resource Reservation Protocol (RSVP) neighbor information.
1.21.2 Command Mode
all modes
1.21.3 Syntax Description
ip-addr |
Optional. Neighbor IP address. Displays detailed information for specified neighbor. |
detail |
Optional. Displays detailed information for all neighbors. |
1.21.4 Default
Displays summary RSVP information for all neighbors.
1.21.5 Usage Guidelines
Use the show rsvp neighbor command to display RSVP neighbor information.
If the RSVP neighbor’s transport IP address differs from its router ID, the IP address specified in the neighbor ip-addr construct must be the RSVP neighbor’s transport IP address.
- Note:
- By default, most show commands (in any mode) display information for the current context only or, depending on the command syntax, for all contexts. If you are an administrator for the local context, you can insert the optional context ctx-name construct, preceding the show command, to view output for the specified context without entering that context. For more information about using the context ctx-name construct, see the context command description.
- Note:
- By appending a space followed by the pipe ( | ) character at the end of a show command, you can filter the output using a set of modifier keywords and arguments. For more information, see Modifying Output of show Commands in Using the CLI.
1.21.6 Examples
The following example displays summary RSVP neighbor information for all RSVP interfaces:
[local]Redback>show rsvp neighbor
--- All RSVP Neighbors --- Nbr Address GR Rest-Time Recov-Time State 17.1.1.3 Yes 60 120 Up 20.1.1.1 Yes 30 60 Up 27.27.27.1 No 30 60 Hello Disabled 28.28.28.1 No 30 60 Hello Disabled 31.1.1.2 No 30 60 Hello Disabled
The summary includes the following information for all RSVP neighbors:
- Nbr Address—Neighbor address: IP Address
- GR—Graceful Restart Enabled: Yes/No
- Rest-Time—Number of seconds that Nbr has to send “Hello” after restarting.
- Recov-Time—Number of seconds that Nbr has to refresh LSPs after restarting.
- State—Up, Down, Hello Disabled, or Restarting
The following example displays detailed information for neighbor 17.1.1.3:
[local]Redback>show rsvp neighbor 17.1.1.3
--- RSVP Neighbor 17.1.1.3 --- Intf Name :to-nbrA GR Enabled :Yes Restart Time :60 (sec) Recovery Time :120 (sec) Nbr Restart Time :20 (sec) Nbr Recovery Time :40 (sec) Restart TTD :14 (sec) Recovery TTD :54 (sec) Hello Status :Restarting Nbr Restart Cnt :9 Last Nbr Restart :09:48:21 Wed Oct 15 2008 Nbr flags :0x0010 Nbr Reference Cnt :300
The detailed display includes the following information:
- Intf Name—Interface Name GR Enabled = Graceful Restart Enabled: Yes/No
- Restart Time—Number of seconds that the local node has to send “Hello” after restarting. Recovery Time = Number of seconds that the local node has to refresh LSPs after restarting. (Restart/Recovery Time is available only if RSVP Hello messages are enabled.)
- Nbr Restart Time—Number of seconds that Nbr has to send “Hello” after restarting. Nbr Recovery Time = Number of seconds that Nbr has to refresh LSPs after restarting. (Restart/Recovery Time is available only if RSVP Hello messages are enabled.)
- Restart TTD—Number of seconds remaining for Nbr to send “Hello”. Recovery TTD = Number of seconds remaining for Nbr to refresh LSPs.
- Hello Status—Enabled/Disabled/Restarting Nbr Restart Cnt = Number of restarts since Nbr discovery.
- Last Nbr Restart—Time and date of the last Nbr restart.
- Nbr flags— Nbr flags.
- Nbr Reference Cnt —The number of structures currently referencing the nbr structure. Both path state blocks and resv state blocks can reference the nbr structure, so there is not always a 1-to-1 relationship between the number of LSPs and the Nbr Reference Cnt.
1.22 show rsvp track
show rsvp track [object-name | detail]
1.22.1 Purpose
Displays information about a specific RSVP tracking object or for all RSVP tracking objects currently configured on the router.
1.22.2 Command Mode
all modes
1.22.3 Syntax Description
object-name |
Optional. Tracking object. |
detail |
Optional. Displays detailed information about all tracking objects currently configured on the router. |
1.22.4 Default
Displays summary information about all RSVP tracking objects that are currently configured on the router.
1.22.5 Usage Guidelines
Use the show rsvp track command to display information about a specific RSVP tracking object or for all RSVP tracking objects currently configured on the router.
1.22.6 Examples
The following example shows how to display summary information about all tracking objects currently configured on the router:
[local]Redback#show rsvp track Track Object Member Count Observer Count Status object1 1 0 DOWN Track1 1 0 UP Track-mtu 3 2 UP
The following example shows how to display information about a tracking object called object1:
[local]Redback#show rsvp track object1 Track Object object1 is DOWN Number of members: 1 RSVP interface:1 is DOWN Tracked by 0 observers
The following example shows how to display detailed information about all tracking objects currently configured on the router:
[local]Redback#show rsvp track detail Track Object Track10 is DOWN Number of members: 0 Tracked by 2 observers RSVP LSP:AC1MTU2AZUL RSVP LSP:AC1AG1VERDE Track Object Track3 is DOWN Number of members: 0 Tracked by 0 observers Track Object Track4 is DOWN Number of members: 0 Tracked by 0 observers Track Object Track5 is DOWN Number of members: 0 Tracked by 0 observers Track Object Track6 is DOWN Number of members: 0 Tracked by 0 observers Track Object Track7 is DOWN Number of members: 0 Tracked by 0 observers Track Object Track8 is DOWN Number of members: 0 Tracked by 0 observers Track Object Track9 is DOWN Number of members: 0 Tracked by 0 observers Track Object Track-mtu is UP Number of members: 6 RSVP interface:IPst.2 is UP RSVP interface:IPst.14 is DOWN RSVP interface:abc3 is DOWN RSVP interface:IPst.4 is UP RSVP interface:abc is DOWN RSVP interface:IPst.3 is DOWN Tracked by 1 observers RSVP LSP:AC1_MTU1_azul Track Object Track-new is UP Number of members: 1 Tracked by 0 observers
1.23 show secured-arp
show secured-arp
1.23.1 Purpose
Displays secured Address Resolution Protocol (ARP) information.
1.23.2 Command Mode
all modes
1.23.3 Syntax Description
This command has no keywords or arguments.
1.23.4 Default
None
1.23.5 Usage Guidelines
Use the show secured-arp command to display secured ARP information.
- Note:
- By default, most show commands in any mode display information for the current context only or, depending on the command syntax, for all contexts. If you are an administrator for the local context, you can insert the optional context ctx-name construct in front of the show command to view output for the specified context without having to enter that context. For more information about using the context ctx-name construct, see the context command description.
- Note:
- By appending a space followed by the pipe ( | ) character at the end of a show command, you can filter the output using a set of modifier keywords and arguments. For more information, see Modifying Output of show Commands in Using the CLI.
1.23.6 Examples
The following example displays secured ARP information:
[local]Redback>show secured-arp Total number of Secured ARP entries in cache: 1 Host Interface i/f grid Circuit 20.1.1.187/32 to-dhcpclient 0x1000000b 11/1 vlan-id 11 20.2.10.0/24 test 0x10000002 11/2
1.24 show service
show service [filter]
1.24.1 Purpose
Displays enabled and disabled services.
1.24.2 Command Mode
All modes
1.24.3 Syntax Description
filter |
Optional. Displays service filter information. |
1.24.4 Default
None
1.24.5 Usage Guidelines
Use the show service command to display enabled and disabled services.
Use the optional filter keyword to display service filter information.
- Note:
- By default, most show commands (in any mode) display information for the current context only or, depending on the command syntax, for all contexts. If you are an administrator for the local context, you can insert the optional context ctx-name construct before the show command to view output for the specified context without entering that context. For more information about the context ctx-name construct, see the context command description.
- Note:
- By appending a space followed by the pipe ( | ) character at the end of a show command, you can filter the output using a set of modifier keywords and arguments. For more information, see Modifying Output of show Commands in Using the CLI.
1.24.6 Examples
The following example displays the output from the show service command:
[local]Redback>show service
Context Services: multiple-contexts enabled card-auto-reload enabled console-break disabled vxworks-log-to-screen enabled upload-coredump disabled crash-dump-dram disabled auto-system-recovery disabled
1.25 show snmp
show snmp {accesses | communities | server | targets | views}
1.25.1 Purpose
Displays Simple Network Management Protocol (SNMP) information, including usage, configured contexts, communities, SNMP daemon status, targets, and views.
1.25.2 Command Mode
All modes
1.25.3 Syntax Description
accesses |
Optional. Displays usage. |
communities |
Optional. Displays the communities. |
server |
Optional. Displays the current state of the SNMP daemon and the User Datagram Protocol (UDP) port on which it is currently configured to listen. |
targets |
Optional. Displays configured SNMP targets (notification receivers). |
views |
Optional. Displays the configured Management Information Base (MIB) views. |
1.25.4 Default
None
1.25.5 Usage Guidelines
Use the show snmp command to display SNMP statistics, including usage, configured contexts, communities, notifications, SNMP daemon status, targets, and views.
- Note:
- By default, most show commands (in any mode) display information for the current context only or, depending on the command syntax, for all contexts. If you are an administrator for the local context, you can insert the optional context ctx-name construct before the show command to view output for the specified context without entering that context. For more information about the context ctx-name construct, see the context command description.
- Note:
- By appending a space followed by the pipe ( | ) character at the end of a show command, you can filter the output using a set of modifier keywords and arguments. For more information, see Modifying Output of show Commands in Using the CLI.
1.25.6 Examples
The following example displays output from the show snmp command with the views keyword:
[local]Redback>show snmp views
restricted system - included non-volatile restricted snmp - included non-volatile restricted snmpEngine - included non-volatile restricted snmpMPDstats - included non-volatile restricted usmStats - included non-volatile
1.26 show snmp alarm
show snmp alarm {active | cleared | model | stats}
1.26.1 Purpose
Displays Simple Network Management Protocol (SNMP) information for SNMP alarms.
1.26.2 Command Mode
all modes
1.26.3 Syntax Description
active |
Display active alarms in Alarm MIB |
cleared |
Display cleared alarms |
model |
Display SNMP alarm model table |
stats |
Display statistics |
1.26.4 Default
None
1.26.5 Usage Guidelines
Use the show snmp alarm command to display SNMP alarm statistics, alarm model configuration, and lists of active and cleared alarms.
- Note:
- By default, most show commands (in any mode) display information for the current context only or, depending on the command syntax, for all contexts. If you are an administrator for the local context, you can insert the optional context ctx-name construct before the show command to view output for the specified context without entering that context. For more information about the context ctx-name construct, see the context command description.
- Note:
- By appending a space followed by the pipe ( | ) character at the end of a show command, you can filter the output using a set of modifier keywords and arguments. For more information, see Modifying Output of show Commands in Using the CLI.
1.26.6 Examples
The following example displays output from the show snmp alarm command with the cleared keyword:
[local]Redback>show snmp alarm cleared ======================================================================= Object name : Value ======================================================================= alarmClearIndex : 3 alarmClearDateAndTime : 2009-4-9, 12:28:19, -8:0 alarmClearEngineID : 80.0.9.30.83.0.0.30.88.1.45.8d [hex] alarmClearEngineAddressType : ipv4(1) alarmClearEngineAddress : 10.12.49.19 alarmClearContextName : local alarmClearLogIndex : 0 alarmClearNotificationID : interfaces.3.3.4.5 alarmClearResourceId : 0.0 alarmClearModelPointer : 0.0
1.27 show snmp ping
show snmp ping [status {name ping-test-name} {details} | {result {name ping-test-name}{success | failed {history} {details}} {output}]
1.27.1 Purpose
Displays information about that status and results of scheduled ping tests.
1.27.2 Command Mode
All modes
1.27.3 Syntax Description
status |
Displays the status of scheduled ping tests. |
result |
Displays the result of the ping test. |
name ping-test-name |
Limits displayed information to the ping test with the name you identify in the ping-test-name argument. |
success |
Displays ping tests that ran successfully. |
failed |
Displays ping tests that failed. |
history |
Displays a history of ping test results up to 12 ping tests. |
details |
Displays a detailed listing of ping test results. |
1.27.4 Default
None
1.27.5 Usage Guidelines
Use this command to display the status and results of the scheduled ping tests. If a hostname is used as the ping target, the details keyword shows the resolved IP address of the hostname; otherwise, it shows the ping target IP address.
When you run the command from a non-local context, only the ping tests defined within that context will display. If you run the commands from the local context, you can view all defined ping tests and the output is organized by context.
1.27.6 Examples
The following example displays output from the show snmp ping command with the result and history keywords:
[local]Redback>show snmp ping result history Context: local, Owner: CLI name idx status sent recv min/max/avg rtt (ms) jitter --------------------- --- ------- ---- ---- -------------------- ---- ip test #3 1 success 15 15 1000/1000/1000 0 ip test #3 2 success 15 15 1000/1000/1000 0 ip test #3 3 failed 15 0 0/0/0 0 ip test #4 1 failed 15 0 0/0/0 0 ip test #4 2 failed 15 0 0/0/0
The following example displays output from the show snmp ping command with the status and details keywords:
[local]Redback>show snmp ping status details Context: local, Owner: CLI name status protocol target freq cnt ------------------- -------- ---------- -------------------- ----- --- ip test enabled ip/icmp ipaddr-or-hostname 86400 15 timeout=60, df, size=nn, pattern=0xff, tos=0xff, ttl=255, src=1.2.3.4 Context: local, Owner: SNMP(test1) name status protocol target freq cnt ------------------- -------- ---------- -------------------- ----- --- ip test enabled ip/icmp ipaddr-or-hostname 86400 15 timeout=60, df, size=nn, pattern=0xff, tos=0xff, ttl=255, src=1.2.3.4
1.28 show snmp traceroute
show snmp traceroute { result traceroute-test-name details | traceroute-test-name details }
1.28.1 Purpose
Displays the status of the current SNMP traceroute tests. If SNMP traceroute tests are configured by SNMP set requests and the value of the traceRouteCtlCreateHopsEntries object is set to “FALSE”, traceroute hop related information will not be displayed when the “detail” option is enabled.
1.28.2 Command Mode
All modes
1.28.3 Syntax Description
traceroute-test-name |
Limits displayed information to the traceroute test with the name you identify in the traceroute-test-name argument. String used to filter in the tests using this string as the test name. |
result |
Displays the result of the traceroute test. |
details |
Displays additional traceroute configurations.. |
1.28.4 Default
None
1.28.5 Usage Guidelines
This command displays the results of the current SNMP traceroute tests. The option traceroute-test-name is used as a test name filter. The detail option is used to display additional hop related information, including hop index, hop IP address, number of probe sent, number of probes received, minimum RTT, max RTT, and average RTT.
1.28.6 Examples
The following example displays output from the show snmp traceroute command with the traceroute-test-name test_1 and details keyword:
[local]Redback>show snmp traceroute test_1 details Context: local Owner: CLI Name status protocol target freq cnt ---------------------- -------- ---------- -------------------- ----- --- test_1 enabled ip/udp 1.1.1.1 600 5 df init-ttl max-ttl port size source timeout tos -------- -------- ------- ------ ----- ---------------- ------- ---- disabled 1 30 33434 0 n/a 3 0x0 Totals: 1 test
The following example displays the results from the show snmp traceroute command with the traceroute-test-name test_1 and the result and details keywords:
[local]Redback>show snmp traceroute result test_1 details Context: local Owner: CLI hop test test Name status count attempts successes last good path ---------------------- ---------- ------ --------- ---------- --------------- test_1 running 3 10 10 Jun 21 18:31:12 IP address = 3.3.3.3 Hop hop IP address sent recv min/max/avg (ms) ---- -------------------- ---- ---- -------------------- 1 1.1.1.1 3 3 0/1/1 2 2.2.2.2 3 3 1/1/1 3 3.3.3.3 3 3 0/1/1 Totals: 1 tests
1.29 show spanning-tree
show spanning-tree bridge-name [details]
1.29.1 Purpose
Shows the spanning-tree information for the bridge instance.
1.29.2 Command Mode
exec
1.29.3 Syntax Description
bridge-name |
Name of the bridge. |
details |
Show detailed spanning-tree information. |
1.29.4 Default
None
1.29.5 Usage Guidelines
Use the show spanning-tree to show the spanning-tree information for the bridge instance; that is, use the command to show the spanning-tree information that applies to the whole bridge.
1.29.6 Examples
The following example shows detailed spanning-tree information for the brdgrp1 bridge:
[local]Redback#show spanning-tree brdgrp1 details
1.30 show spanning-tree circuit
show spanning-tree bridge-name circuit circuit-id [details]
1.30.1 Purpose
Shows the spanning-tree information for specific circuits on the bridge.
1.30.2 Command Mode
exec
1.30.3 Syntax Description
bridge-name |
Name of the bridge. |
circuit circuit-id |
Specifies circuits on the bridge. See Table 4 for the expanded syntax for the circuit-id argument. |
details |
Provide detailed spanning-tree information. |
1.30.4 Default
None
1.30.5 Usage Guidelines
Use the show spanning-tree to show the spanning-tree information for specific circuits on the bridge on the SmartEdge router.
The circuit-id argument is composed of the keywords and arguments as described in the following syntax:
slot/port {ethernet | vlan vlan-id}
Table 4 describes the components of the circuit-id argument:
Field |
Description |
---|---|
slot |
Chassis slot number of the traffic card with the bridged circuits. |
port |
Port number of the port with the bridged circuits. |
ethernet |
Clears all the circuits on the specified Ethernet port. |
vlan vlan-id |
A filter that limits the command to a specified virtual LAN (VLAN) 802.1Q tunnel or PVC. The vlan-id argument is one of the following constructs:
If you specify the VLAN tag value for an 802.1Q tunnel, this command clears subscriber sessions on all the PVCs in the tunnel. The range of values for any VLAN tag value is 1 to 4095. |
1.30.6 Examples
The following example shows detailed spanning-tree information specific to the circuits in the Ethernet port 2/1 in the brdgrp1 bridge:
[local]Redback#show spanning-tree brdgrp1 circuit 2/1 ethernet details
1.31 show spanning-tree track
show spanning-tree track {master-bridge-name context | all | all-master
1.31.1 Purpose
Displays the names of the RSTP master bridge or bridges and the names of their non-RSTP client bridges.
1.31.2 Command Mode
exec
1.31.3 Syntax Description
master-bridge-name |
Name of the RSTP master bridge. |
context |
Name of the context in which the RSTP master bridge exists. |
all |
Display the names of all the spanning-tree master bridges in all contexts and each of their clients. |
all-master |
Display the names of all the spanning-tree master bridges in all contexts. |
1.31.4 Default
None
1.31.5 Usage Guidelines
Use the show spanning-tree track command to display the names of the RSTP master bridge or bridges and the names of their non-RSTP client bridges.
1.31.6 Examples
The following example shows the use of the show spanning-tree tracking command to display the clients of the spanning tree master bridge ted in the context local:
[local]Redback#show spanning-tree track ted local Role Bridge Group Context Master ted local clients : 1 master cct count : 0 master pw count : 0 client cct count : 0 client pw count : 0 Client bob local client cct count : 0 client pw count : 0
1.32 show sse
show sse {group | partition} [group_name [partition_name]] [detail]
1.32.1 Command Mode
all modes
1.32.2 Syntax Description
group |
Display SSE group information. |
partition |
Displays SSE card partition information. |
group_name |
Optional. Name of the SSE group. |
partition_name |
Optional. Name of the partition. |
detail |
Optional. Display detailed information for the specified SSE group or partition. |
1.32.3 Usage Guidelines
Displays SSE group or SSE partition information.
See Table 5 for a description of the fields displayed in the output of the command.
Output Field |
Description |
---|---|
Group |
SSE group name. |
ID |
SSE group ID: 1 to 32. |
Description |
Group description. |
State |
Service state of the SSE group:
|
Redundancy |
SSE group redundancy setting: Network or Disk. |
Revert |
Switch mode configured: Enabled or Disabled. |
Disk Mode |
Configured disk mode: RAID-0, RAID-1, or Independent. |
Switch Trigger Reason |
If applicable, trigger reason for redundancy switch: N/A, Manual, or Auto. |
Switch Failed Reason |
If applicable, switch failed reason: Alarm events. |
Partition(s) |
Number of partitions configured. |
Name |
Name of each partition configured. |
ID |
Partition ID: 1 to 16. |
Group Name |
Name of group. |
Group ID |
Group ID: 1 to 32. |
State |
Operational status of the partition: Up, Down, Stale. |
Size (GB) |
Configured size of the partition. |
Percent Used (%) |
Data used on the partition, expressed as a percentage. |
Disk |
Disk number, if designated: 1, 2, or All. |
Mirrored |
Mirror data to standby disk, if network redundancy is configured: Enabled, Disabled, N/A. |
Alarm Low Space |
Alarm for low partition space: Enabled or Disabled. |
Trigger Percentage |
Triggering disk space in percentage; clear percentage in brackets. |
Alarm(s) |
Alarms triggered on the partition. |
Primary |
Primary slot assigned to the group: slot slot_num. |
Secondary |
If redundancy is configured, the secondary slot assigned to the group: slot slot_num. |
Disk Mode |
Configured disk mode for the group: RAID-0, RAID-1, or Independent. |
Redundancy State |
The acting status of the redundancy group. Standalone is assigned for nonredundant groups: Active, Standby, or Standalone. |
Disk ID(s) Ready |
Indicates which disks are ready for service: 1, 2, All, or None. |
Total Disk Size |
Total disk size available on the slot/disk, rounded to the nearest GB. |
Data Status |
The redundancy status of the data on the disk. Sync-in-progress means that the redundancy data is being synchronized from the current active slot/disk: Up-to-date or Sync-in-progress. |
Alarm(s) |
Alarm(s) raised for the slot/disk. |
Sync Progress |
If synchronization is happening, it shows the progress as a status bar with percentage completed, as well as size synchronized and total to be synchronized. |
Time Remaining |
Estimated time remaining for the sync to complete: HH:MM:SS. |
Speed |
Current speed of the sync in KB/sec. |
Mean Speed |
Mean speed of the sync in KB/sec. |
1.32.4 Examples
[local]Redback#show sse group Group ID Redundancy Disk Mode Slot State ----------------------------------------------------------------- grp1 1 network-redundant Independent 2 (5) Down
[local]Redback#show sse group detail Name : grp1 ID : 1 Description : ------------------------------------------------------------------------ State : Up Redundancy : network-redundant Disk Mode : Independent Revert : no revert Switch Reason : Standby INS Switch Failed Reason: No Reason Alarms : NONE Partition(s) : -------------------------------------------- Name : ptn1 ID : 1 Group Name : grp1 Group ID : 1 State : Up Size (GB) : 2 Percent Used : 9 Disk : 1 Mirrored : Enabled Alarm Low Space : Enabled Trigger Percentage : 80 (clear 70) Alarms : NONE Name : ptn2 ID : 2 Group Name : grp1 Group ID : 1 State : Up Size (GB) : 2 Percent Used : 2 Disk : 1 Mirrored : Disabled Alarm Low Space : Enabled Trigger Percentage : 80 (clear 70) Alarms : NONE Primary Slot : 2 -------------------------------------------- Redundancy State : Active Slot State : Up Disk ID(s) Ready : All Total Size (GB) : 268 Data Status : Up-To-Date Active Alarms : NONE Secondary Slot : 5 -------------------------------------------- Redundancy State : Standby Slot State : Up Disk ID(s) Ready : 1 Total Size (GB) : 134 Data Status : Up-To-Date Active Alarms : NONE
[local]Redback#show sse partition Group ID Partition ID Size (GB) Disk State ---------------------------------------------------------------- grp1 1 ptn1 1 2 1 Up grp1 1 ptn2 2 2 1 Up
[local]Redback#show sse partition detail Name : ptn1 ID : 1 Group Name : grp1 Group ID : 1 State : Up Size (GB) : 2 Percent Used : 9 Disk : 1 Mirrored : Enabled Alarm Low Space : Enabled Trigger Percentage : 80 (clear 70) Alarms : NONE Name : ptn2 ID : 2 Group Name : grp1 Group ID : 1 State : Up Size (GB) : 2 Percent Used : 2 Disk : 1 Mirrored : Disabled Alarm Low Space : Enabled Trigger Percentage : 80 (clear 70) Alarms : NONE
1.33 show sse counters
show sse {group | partition} counters [group_name [partition_name]]
1.33.1 Command Mode
all modes
1.33.2 Syntax Description
group |
Display SSE group information. |
partition |
Display SSE card partition information. |
group_name |
Optional. Name of the SSE group. |
partition_name |
Optional. Name of the partition. |
1.33.3 Usage Guidelines
Displays SSE group or SSE partition counters.
1.33.4 Examples
[local]Redback#show sse group counters Name : grp1 ID : 1 Redundancy : network-redundant Primary Slot : 2 Redundancy State : Active Secondary Slot : 5 Redundancy State : Standby Partition(s) : ------------------------------------------------------------------------ timestamp: 11486967468 timestamp secs: 11486 timestamp usecs: 967468 Name : ptn1 ID : 1 Group Name : grp1 Group ID : 1 Disk Allocated : 1 Partition Size (GB) : 2 Percent Used : 9 Percent Available : 91 Network Send : 2097100 Network Received : 0 Disk Write (KB) : 12 Disk Read (KB) : 2097826 Activity Log : 1 Bit Map : 128 Local Count : 0 Local Pending : 0 Unacknowledged : 0 Application Pending : 0 timestamp: 11486968702 timestamp secs: 11486 timestamp usecs: 968702 Name : ptn2 ID : 2 Group Name : grp1 Group ID : 1 Disk Allocated : 1 Partition Size (GB) : 2 Percent Used : 2 Percent Available : 98 Network Send : 0 Network Received : 0 Disk Write (KB) : 32 Disk Read (KB) : 738 Activity Log : 2 Bit Map : 0 Local Count : 0 Local Pending : 0 Unacknowledged : 0 Application Pending : 0
1.34 show ssh-attributes
show ssh-attributes
1.34.1 Purpose
Displays information about configured Secure Shell (SSH) attributes and the number of current connections.
1.34.2 Command Mode
All modes
1.34.3 Syntax Description
This command has no keywords or arguments.
1.34.4 Default
None
1.34.5 Usage Guidelines
Use the show ssh-attributes command to display information about configured SSH attributes and the number of current connections.
- Note:
- By default, most show commands (in any mode) display information for the current context only or, depending on the command syntax, for all contexts. If you are an administrator for the local context, you can insert the optional context ctx-name construct before the show command to view output for the specified context without entering that context. For more information about the context ctx-name construct, see the context command description.
- Note:
- By appending a space followed by the pipe ( | ) character at the end of a show command, you can filter the output using a set of modifier keywords and arguments. For more information, see Modifying Output of show Commands in Using the CLI.
1.34.6 Examples
The following example displays SSH attributes:
[local]Redback>show ssh-attributes
ssh attributes -------------- start-drop 50 (connections) rate-drop 100 (percentage) full-drop 50 (connections) current 0 (connections)
1.35 show static route
show static route [print-prefix] [all]
1.35.1 Purpose
Displays static route information.
1.35.2 Command Mode
all modes
1.35.3 Syntax Description
print-prefix |
Optional. Displays the IP address and prefix length for static routes with multiple next hops. By default, entries in the Prefix field are left blank. |
all |
Optional. Displays static route information for all contexts. |
1.35.4 Default
None
1.35.5 Usage Guidelines
Use the show static route command to display static route information.
- Note:
- By default, most show commands (in any mode) display information for the current context only or, depending on the command syntax, for all contexts. If you are an administrator for the local context, you can insert the optional context ctx-name construct, preceding the show command, to view output for the specified context without entering that context. For more information about using the context ctx-name construct, see the context command description.
- Note:
- By appending a space followed by the pipe ( | ) character at the end of a show command, you can filter the output using a set of modifier keywords and arguments. For more information, see Modifying Output of show Commands in Using the CLI.
Table 6 describes the show static route command output fields.
Field |
Description |
---|---|
Prefix |
IP address and prefix length. |
Best |
|
NType |
Next-hop type. The types can be addr (IP address), intf (interface), dvsr, and cntx (context). The dvsr next-hop type is a special type of IP address. |
Addr/Intf/Cntx |
Detail next-hop information. The information displayed can either be an IP address, an interface name, a context name, or null0 (a special interface name). |
NS |
Next-hop status. The status is either up or dn (down). It reflects the status of either the next-hop IP address reachability, the next-hop interface status, or the next-hop context. |
Dist |
Route distance to be advertised into the RIB. |
P |
An asterisk (*) indicates that the route is a permanent announced route. |
Tag |
Tag value of the prefix. |
1.35.6 Examples
The following example displays output from the show static route command:
[local]Redback>show static route
Prefix Best NType Addr/Intf/Cntx NS Dist P Tag 8.1.1.1/30 yes dvsr 165.63.39.15 up 1 0x0 10.1.1.0/24 yes intf ether3/1 up 1 0x0 no intf op-net-lan up 10 0x0 10.1.2.0/24 yes intf to-redback up 1 0x0 10.11.12.0/24 yes cntx foo up 1 0x0 20.0.0.0/8 yes intf to-redback up 1 0x0 yes addr 165.63.39.1 up 1 0x0 30.0.0.0/8 yes intf null0 up 1 0x0 40.1.0.0/16 no- cntx vpn-abc dn 1 0x0 50.1.2.0/24 yes addr 165.63.39.2 up 1 * 0x0 Total static route in context local: 8, total path: 10
1.36 show subscribers
To display the basic subscriber status fields:
show subscribers [{agent-circuit-id id | agent-remote-id id | all | {session slot/port[:chan-num[:sub-chan-num]] [circuit-id]} | session l2tp lns id | username subscriber}]
To display the digital subscriber line (DSL) attributes associated with subscribers:
show subscribers access-line [{agent-circuit-id id | agent-remote-id id | all | {session slot/port[:chan-num[:sub-chan-num]] [circuit-id]} | session l2tp lns id | username subscriber}]
To display the attributes of active subscriber sessions:
show subscribers active [{agent-circuit-id id | agent-remote-id id | all | {session slot/port[:chan-num[:sub-chan-num]] [circuit-id]} | session l2tp lns id | username subscriber}]
To display the Mobile IP attributes associated with subscribers:
show subscribers mobile-ip [{agent-circuit-id id | agent-remote-id id | all | {session slot/port[:chan-num[:sub-chan-num]] [circuit-id]} | session l2tp lns id | username subscriber}]
To display the authentication, authorization, and accounting (AAA) logs of subscribers:
show subscribers log [{{session slot/port[:chan-num[:sub-chan-num]] [circuit-id]} | session l2tp lns id | username subscriber}]
To display a summary of subscriber information:
show subscribers summary [[ipv4 | ipv4-only | ipv6 | ipv6-only | dual-stack] all]
To display information about the subscriber licenses currently being used by the system:
show subscribers license summary
To display IP information associated with subscribers:
show subscribers address username subscriber
1.36.1 Purpose
Displays subscriber information.
1.36.2 Command Mode
all modes
1.36.3 Syntax Description
agent-circuit-id id |
Optional. A filter that limits the information displayed to the subscriber specified by the agent circuit ID in a subscriber record. Enter the id argument as a structured subscriber username in the form subscriber@context. |
agent-remote-id id |
Optional. A filter that limits the information displayed to the subscriber specified by the agent remote ID in a subscriber record. Enter the id argument as a structured subscriber username in the form subscriber@context. |
all |
Optional. Displays information about all subscribers in all contexts. This keyword is available only to administrators in the local context. |
session |
Optional. Limits the command output to the specified session or circuit. |
slot |
Optional. Chassis slot number for a traffic card. |
port |
Optional. Port number on the specified traffic card. |
circuit-id |
Optional. A subscriber session identifier, or a subscriber username that filters which subscriber information this command displays. See Table 7 for information about the circuit-id argument. |
l2tp lns id |
Optional. Limits the output of the command output to the specified Layer 2 Tunneling Protocol (L2TP) network server (LNS) circuit. |
username subscriber |
Optional. Limits the command output to subscribers specified by a subscriber name. Enter the subscriber argument as a structured subscriber username in the form subscriber@context. |
access-line |
Optional. Displays the DSL attributes. |
active |
Optional. Displays the attributes of active subscriber sessions. |
mobile-ip |
Optional. Displays the Mobile IP attributes for the specified subscriber sessions. |
log |
Optional. Displays the AAA log. |
summary |
Optional. Displays the total number of subscribers and their encapsulations in the current context. |
ipv4 |
Optional. Display all IPv4 subscriber sessions on the system (single and dual-stack). Information is displayed for the current context only; to display information for all contexts, include the all keyword in the command string. |
ipv4-only |
Optional. Display ipv4 subscriber sessions only (for subscribers that are authorized to carry IPv4 traffic only). Information is displayed for the current context only; to display information for all contexts, include the all keyword in the command string. Be aware that this keyword does not display information about dual-stack subscribers that have only the IPv4 stack active. |
ipv6 |
Optional. Display all IPv6 subscriber sessions on the system (single and dual-stack). Information is displayed for the current context only; to display information for all contexts, include the all keyword in the command string. |
ipv6-only |
Optional. Display IPv6 subscriber sessions only (for subscribers that are authorized to carry IPv6 traffic only). Information is displayed for the current context only; to display information for all contexts, include the all keyword in the command string. Be aware that this keyword does not display information about dual-stack subscribers that have only the IPv6 stack active. |
dual-stack |
Optional. Display dual-stack subscriber sessions only (for subscribers that are authorized for both IPv4 and IPv6, and can simultaneously support both IPv4 and IPv6 traffic). Information is displayed for the current context only; to display information for all contexts, include the all keyword in the command string. Be aware that this keyword only displays information for dual-stack subscribers that have both stacks (IPv4 and IPv6) active. |
license |
Optional. Displays information about the subscriber licenses currently configured on the system. |
address |
Optional. Displays the IP information. |
1.36.4 Default
Displays information for all active subscribers in the current context.
1.36.5 Usage Guidelines
Use the show subscribers command to display subscriber information. This includes basic subscriber status fields, DSL attributes, attributes of active subscriber sessions, Mobile IP attributes, AAA log or logs, a summary of subscriber information, and IP addresses associated with subscribers.
The circuit-id argument represents the following keywords and arguments; see Table 7:
clips [clips-session] | pppoe [pppoe-session] | vlan-id vlan-id [pppoe [pppoe-session] | clips [clips-session]] | vpi-vci vpi vci [pppoe [pppoe-session] | clips [clips-session]]
Construct |
Description |
---|---|
clips clips-session |
A filter that limits the command to a specified CLIPS circuit on a port, channel, 802.1Q PVC, or ATM PVC. If the CLIPS circuit is on an 802.1Q or ATM PVC, also specify the circuit identifier for the 802.1Q or ATM PVC. If the session is not specified, the command applies to all CLIPS sessions in the context. The range of values for the clips-session argument is 1 to 262,144. |
pppoe pppoe-session |
A filter that limits the command to a specified PPPoE session. If the pppoe-session argument is not specified, the command applies to all PPPoE sessions in the context. |
vlan-id vlan-id |
A filter that limits the command to a specified virtual LAN (VLAN) 802.1Q tunnel or PVC. The vlan-id argument is one of the following constructs:
If you specify the VLAN tag value for an 802.1Q tunnel, this command clears subscriber sessions on all the PVCs within the tunnel. The range of values for any VLAN tag value is 1 to 4,095. |
vpi-vci vpi vci |
A filter that limits the command to a specified ATM PVC. The ATM PVC is specified by the virtual path identifier (VPI) and virtual circuit identifier (VCI). The range of values is 0 to 255 and 1 to 65,534, respectively. |
The slot and port assignments for the SmartEdge routers are described in their respective hardware guides.
Use the access-line keyword to display information about DSL line attributes for each subscriber. The output information includes the parameters learned from the DSL attribute extension Type, Length, Value (TLV) in the General Switch Management Protocol (GSMP) Port Up message for the DSL.
The DSL attributes are learned from the DSL access multiplexer (DSLAM). They can be learned by GSMP messages and from PPPoE or DHCP tags during a subscriber session setup. Each learned attribute is preceded by the words Access Node Control Protocol (ANCP) or DSL Forum (DSLF) when printed. This indicates the mechanism by which it was learned. For example, ANCP means it was learned by ANCP; DSLF was learned from a tag during subscriber session setup; and so forth.
Table 8 lists the types of DSL data and the values that this command can display.
Type of Data |
Value |
---|---|
Agent-Circuit-ID |
This includes DSLAM slot, port and channel number. |
Internal Circuit |
This includes the internal circuit number, slot, port and channel numbers. |
Neighbor ID |
Neighbor ID number |
DSL Line State |
|
DSL Data Rates |
|
- Note:
- By default, most show commands (in any mode) display information for the current context only or, depending on the command syntax, for all contexts. If you are an administrator for the local context, you can insert the optional context ctx-name construct, preceding the show command, to view output for the specified context without entering that context. For more information about the context ctx-name construct, see the context command description.
- Note:
- By appending a space followed by the pipe ( | ) character at the end of a show command, you can filter the output using a set of modifier keywords and arguments. For more information, see Modifying Output of show Commands in Using the CLI.
Use the show bindings command to get the binding information that optionally can be specified in the show subscribers command. For information on the show bindings command, see the Command List.
The show subscribers command used with the active keyword, provides information on the dynamic policy rules applied to active subscriber sessions.
The slot and port numbering rules for the SmartEdge 100, SmartEdge 400, and SmartEdge 800 routers are described in their respective hardware guides.
Use the show subscribers summary command to display information about the subscriber sessions on the system. The following information is displayed:
- The type of subscriber sessions whose information is displayed
- The number of subscriber sessions currently being authenticated.
- The number of active subscriber sessions.
- The number of subscriber sessions currently disconnecting.
- Note:
- The ipv4-only and ipv6-only keywords do not display information about dual-stack sessions that have only the specified stack active. For example, the ipv4-only keyword does not display information for dual-stack sessions that have only the IPv4 stack active.
Use the show subscribers license summary command to display the subscriber licenses currently being used by the system. Usage information for following types of subscribers is displayed:
- LAC
- IPv4
- IPv6
- Dual-stack
Subscriber licenses are applicable to LAC, IPv4, and dual-stack subscribers only, and IPv6 licenses are applicable to IPv6 and dual-stack subscribers. Dual-stack subscribers must have an IPv4 license and an IPv6 license configured.
1.36.6 Examples
The following example shows the default output:
[local]Redback>show subscribers Type CIRCUIT SUBSCRIBER CONTEXT START TIME ----------------------------------------------------------------------- PPPOE 00001 pppoe@redback.com company1 JUN 30 17:46:49 2005 VIPSRC 00002 00:dd:00:00:00:01 isp1 JUN 30 00:03:11 2005 VIPSRC 00003 00:dd:00:00:00:02 isp1 JUN 30 00:03:01 2005 VIPSRC 00004 00:dd:00:00:00:03 isp1 JUN 30 00:03:01 2005 VIPSRC 00005 00:dd:00:00:00:04 isp1 JUN 30 00:03:11 2005 VIPSRC 00006 00:dd:00:00:00:05 isp1 JUN 30 00:03:11 2005 ----------------------------------------------------------------------- Total=6 Type Authenticating Active Disconnecting PPP 0 0 0 PPPoE 0 1 0 DOT1Q 0 0 0 CLIPs 0 5 0 ATM-B1483 0 0 0 ATM-R1483 0 0 0
The following example displays the information for an active subscriber; it includes both the absolute timeout action and traffic limit action fields:
[local]Redback>show subscribers active username client32@lns.com
client32@lns.com Circuit L2TP LNS 8744119 Internal Circuit 255/16:1023:63/5/2/8744119 Current port-limit unlimited context-name lns (applied) ip pool (applied from sub_default) absolute timeout action 1 (applied from sub_default) traffic limit action 1 (applied from sub_default) ip address 192.168.27.2 (applied from pool) timeout absolute 60 (applied) timeout idle 60 (applied)
The following example shows the dynamic policy access control lists (ACLs) applied in the forward direction to the active subscriber session usr1@local. For information on the dynamic policy fields displayed in both show commands, see show access-group command in the Command List:
[local]Redback>show subscribers active usr1@local Circuit 2/1 clips 1 Internal Circuit 2/1:1023:63/4/2/1 Interface bound clips1 Current port-limit unlimited ip address 11.1.0.1 (applied) forward policy in forpol (applied) dynamic policy acl (applied in: fwd) ip in forward srcip 11.1.0.51/32 tos 0x08 0x1e class c1 fwd ip in forward srcip 11.1.0.51/32 tos 0x40 0xe0 class c1 fwd ip in forward srcip 11.1.0.51/32 tos 0x48 0xfe class c1 fwd ip in forward srcip 11.1.0.51/32 tos 0x0c 0x1e class c1 fwd ip in forward srcip 11.1.0.51/32 dscp af41 class c1 fwd
Use the show subscribers active all command to view if the RFlow profile is applied to the subscriber in the ingress direction (in), egress direction (out), or bi-directionally (both). In the following example, the flow ip profile has been applied at ingress:
[local]Redback# show subscribers active all client2162833@local Circuit 4/1:1 vpi-vci 33 145 pppoe 2450 Internal Circuit 4/1:1:63/1/2/8193 Interface bound subs Current port-limit unlimited ip pool subs (applied from sub_default) ip source-validation 1 (applied from sub_default) ip address 2.2.0.1 (applied from pool) flow ip profile ingress-flow:in (applied)
The following example includes DSL fields in the command output:
[local]Redback>show subscribers access-line test@local Agent Circuit ID "DSLAM1-slot0-port0-channel2" Internal Circuit 4/3:1023:63/1/2/6 Neighbor ID 10.13.16.98:6068 ANCP Line State SHOWTIME ANCP Actual Data Rate Downstream (kbps) 7777 (applied)
The following example shows the vendor-class-identifier (dhcp vendor class id) is applied to the user session and used by the system for context selection.
[local]Redback>show subscribers active 00:00:68:0d:01:02@pacbell.net Session state Up Circuit 10/1 vlan-id 10:10 clips 131100 Internal Circuit 10/1:1023:63/7/2/28 Interface bound subs Current port-limit unlimited dhcp vendor class id pacbell.net (not applied) dhcp max-addrs 1 (applied) context-name pacbell.net (not applied) dhcp vendor class id pacbell.net (applied) IP host entries installed by DHCP: (max_addr 1 cur_entries 1) 30.30.30.10 00:00:68:0d:01:02
The following example shows how to display information about the dual-stack sessions on the system:
[local]Redback#show subscribers summary dual-stack ------------------------------------------------------------------------------ Total=0 Type Authenticating Active Disconnecting PPP 0 0 0 PPPoE 0 1 0 DOT1Q 0 0 0 CLIPs 0 0 0 ATM-B1483 0 0 0 ATM-R1483 0 0 0 Mobile-IP 0 0 0
The following example shows how to display the number of subscriber licenses that are in use for each type of subscriber:
[local]Redback#show subscribers license summary [ -------------------------------------------------------------------------------- Subscriber-Type Subscriber-License IPv6-License Used Used LAC 0 0 IPv4 Only 1 0 IPv6 Only 0 0 Dual-Stack 0 0
1.37 show system alarm
For SSE cards, the syntax is:
show system alarm [all | sse [group_ID [partition_ID]]]
For ports on Asynchronous Transfer Mode (ATM) OC, Ethernet, or Packet over SONET/SDH (POS) traffic cards, the syntax is:
show system alarm [all | slot[/port]]
1.37.1 Purpose
Displays system-level, card-level, or port-level alarms.
1.37.2 Command Mode
All modes
1.37.3 Syntax Description
all |
Optional. Displays alarms at all levels. |
slot |
Optional. Chassis slot number of the traffic card for which card-, port-, channel-, and subchannel-level alarms are displayed. |
port |
Optional. Card port number of the port for which port-, channel-, and subchannel-level alarms are displayed. |
chan-num |
Optional. Channel number for which channel- and subchannel-level alarms are displayed. The range of values depends on the type of port. |
sub-chan-num |
Optional. Subchannel number for which subchannel-level alarms are displayed. The range of values depends on the type of port. |
sse |
Optional. Displays alarm information for all SSE group and partition alarms. |
group_ID |
Optional. Displays alarm information for the specified SSE group ID. See the output of the show sse group command for valid values. |
partition_ID |
Optional. Displays alarm information for the specified partition ID. See the output of the show sse partition command for valid values. |
1.37.4 Default
Displays system-level alarms only.
1.37.5 Usage Guidelines
Use the show system alarm command to display system-level, card-level, port-level, channel-level, or subchannel-level alarms.
Each succeeding argument restricts the display to the alarms at that level and below and to the alarms for that card, or port, channel, or subchannel.
- Note:
- By default, most show commands (in any mode) display information for the current context only or, depending on the command syntax, for all contexts. If you are an administrator for the local context, you can insert the optional context ctx-name construct, preceding the show command, to view output for the specified context without entering that context. For more information about using the context ctx-name construct, see the context command description.
- Note:
- By appending a space followed by the pipe ( | ) character at the end of a show command, you can filter the output using a set of modifier keywords and arguments. For more information, see Modifying Output of show Commands in Using the CLI.
Use the show port detail command (in any mode) to view the alarms for a port. See the Command List for more information.
Use the show diag command (in any mode) to view the results of the power-on diagnostics (POD) or on-demand diagnostics (ODD).
1.37.6 Examples
The following example displays system-level alarms only:
[local]Redback>show system alarm
Timestamp Type Source Severity Descriptions -------------------------------------------------------------------------------------- Dec 16 19:32:01 chassis Minor Chassis power failure - side B
The following example displays all system-level alarms:
[local]Redback#show system alarm all Timestamp Type Source Severity Description --------------------------------------------------------------------------- Jul 27 13:24:35 chassis Minor Chassis power failure - side A1 Jul 27 13:24:35 chassis Minor Chassis power failure - side A2 Jul 27 16:27:32 sse 5d2 Major Hard disk missing Jul 27 13:24:36 xcrp4-base 7 Major Backup fail: peer dead Jul 27 13:24:36 xcrp4-base 8 Critical Controller missing Jul 27 13:24:46 xcrp4-base 8 Major Controller auto switch completed
The following example displays alarms at the traffic card level and below only; in this case, the traffic card is not installed:
[local]Redback#show system alarm 4
Timestamp Type Source Severity Descriptions --------------------------------------------------------------------------- Dec 10 18:48:33 oc3e-8-port 4 Critical Circuit pack missing
The following example displays alarms at the port-level and below only; in this case, only a channel alarm is present:
[local]Redback#show system alarm 13/2 Timestamp Type Source Severity Descriptions --------------------------------------------------------------------------- Dec 10 18:48:49 oc12e-4-port 13/2:1 Major Path alarm indication signal (AIS-P)
1.38 show system nvlog
show system nvlog
1.38.1 Purpose
Displays the contents of nonvolatile memory (NVRAM) on the controller card to which you are connected.
1.38.2 Command Mode
All modes
1.38.3 Syntax Description
This command has no keywords or arguments.
1.38.4 Default
None
1.38.5 Usage Guidelines
Use the show system nvlog to display the contents of NVRAM on the controller card to which you are connected. The NVRAM stores logs of trap- and panic-related messages from the operating system and can be used to help debug system crashes in the absence of a local console (connected to the Craft 2 port). If your system does not support NVRAM, you receive the following error message: This XCRP doesn't support this feature.
- Note:
- By default, most show commands (in any mode) display information for the current context only or, depending on the command syntax, for all contexts. If you are an administrator for the local context, you can insert the optional context ctx-name construct before the show command to view output for the specified context without entering that context. For more information about the context ctx-name construct, see the context command description.
- Note:
- By appending a space followed by the pipe ( | ) character at the end of a show command, you can filter the output using a set of modifier keywords and arguments. For more information, see Modifying Output of show Commands in Using the CLI.
1.38.6 Examples
The following example displays the contents of the NVRAM on the active controller card:
[local]Redback>show system nvlog
panic: testing Redback: dumpsys called dumping to dev 10,33 offset 8 dump succeeded !!!vxWorks sent REBOOT intr, will shutdown BSD!!! !!!vxWorks sent REBOOT intr, will shutdown BSD!!! !!!vxWorks sent REBOOT intr, will shutdown BSD!!!
1.39 show tacacs+ server
show tacacs+ server [{{ip-addr | hostname} [port tcp-port]}]
1.39.1 Purpose
Displays information for one or all Terminal Access Controller Access Control System Plus (TACACS+) servers in the current context.
1.39.2 Command Mode
all modes
1.39.3 Syntax Description
ip-addr |
Optional. IP address of the TACACS+ server for which more detailed information is to be displayed. Additional information includes detailed error and status counters, such as packets received and transmitted. |
hostname |
Optional. Hostname of the TACACS+ server. |
port tcp-port |
Optional. TACACS+ server Transmission Control Protocol (TCP) port. The range of values is 1 to 65,536. If no port is specified, TCP port number 49 is used. |
1.39.4 Default
None
1.39.5 Usage Guidelines
Use the show tacacs+ server command to display information for one or all TACACS+ servers in the current context, including the IP address and the key set by the tacacs+ server command (in context configuration mode), and the values set by the tacacs+ max-retries and tacacs+ timeout commands (in context configuration mode).
Use the ip-addr or hostname argument to display detailed information for a particular server; otherwise, the system displays summary information for all servers in the context.
- Note:
- By default, most show commands (in any mode) display information for the current context only or, depending on the command syntax, for all contexts. If you are an administrator for the local context, you can insert the optional context ctx-name construct, preceding the show command, to view output for the specified context without entering that context. For more information about using the context ctx-name construct, see the context command description.
- Note:
- By appending a space followed by the pipe ( | ) character at the end of a show command, you can filter the output using a set of modifier keywords and arguments. For more information, see Modifying Output of show Commands in Using the CLI.
1.39.6 Examples
The following example displays summary information for all TACACS+ servers in the context:
[local]Redback#show tacacs+ server
IP Address/Hostname Port Timeout/Max-Tries Key ----------------------------------------------------------------- 10.12.121.211 49 5/1 mykey 10.12.209.171 49 5/1 otherkey
The following example displays information for a specific TACACS+ server:
[local]Redback#show tacacs+ server 10.12.211.121
IP Address/Hostname Port State In-svc Key ----------------------------------------------------------------------- 10.12.211.121 49 untried alive mykey Counter Value ------- ---------- Current sessions 0 Transmitted packets 8 Received packets 8 Dropped packets 0 Connection errors 0 Connection timeouts 0 Host unreachable errors 0 Transmission errors 0 Reception errors 0 Authentication timeouts 0 Authorization timeouts 0 Accounting timeouts 0
1.40 show tcp
show tcp [{brief [all] | md5 | statistics | tcb tcpcb-addr}]
1.40.1 Purpose
Displays Transmission Control Protocol (TCP) Internet connections, statistics, and keepalive settings.
1.40.2 Command Mode
all modes
1.40.3 Syntax Description
brief |
Optional. Displays active Internet connections. |
all |
Optional. Displays active Internet connections, including servers. Used with the brief keyword. |
md5 |
Optional. Displays Message Digest 5 (MD5) entries. |
statistics |
Optional. Displays TCP statistics. |
tcb tcpcb-addr |
Optional. TCP connection for which details are to be displayed. |
1.40.4 Default
None
1.40.5 Usage Guidelines
Use the show tcp command to display TCP Internet connections, statistics, and keepalive settings.
- Note:
- By default, most show commands (in any mode) display information for the current context only or, depending on the command syntax, for all contexts. If you are an administrator for the local context, you can insert the optional context ctx-name construct before the show command to view output for the specified context without entering that context. For more information about the context ctx-name construct, see the context command description.
- Note:
- By appending a space followed by the pipe ( | ) character at the end of a show command, you can filter the output using a set of modifier keywords and arguments. For more information, see Modifying Output of show Commands in Using the CLI.
1.40.6 Examples
The following example displays output when the statistics keyword is specified:
[local]Redback>show tcp statistics
tcp: 85778 packets sent 33921 data packets (934491 bytes) 323 data packets (91638 bytes) retransmitted 26522 ack-only packets (77668 delayed) 0 URG only packets 0 window probe packets 24871 window update packets 141 control packets 123389 packets received 33053 acks (for 936341 bytes) 537 duplicate acks 0 acks for unsent data 102667 packets (37396219 bytes) received in-sequence 132 completely duplicate packets (189 bytes) 0 old duplicate packets 167 packets with some dup. data (232 bytes duped) 39 out-of-order packets (13 bytes) 0 packets (0 bytes) of data after window 0 window probes 7 window update packets 1 packet received after close 0 discarded for bad checksums 0 discarded for bad header offset fields 0 discarded because packet too short 26 connection requests 75 connection accepts 82 connections established (including accepts) 98 connections closed (including 24 drops) 18 embryonic connections dropped 32255 segments updated rtt (of 32538 attempts) 333 retransmit timeouts 1 connection dropped by rexmit timeout 0 persist timeouts (resulting in 0 dropped connections) 110 keepalive timeouts 86 keepalive probes sent 24 connections dropped by keepalive 6023 correct ACK header predictions 89333 correct data packet header predictions 224 PCB hash misses 64 dropped due to no socket 0 connections drained due to memory shortage 1 bad connection attempt 79 SYN cache entries added 0 hash collisions 75 completed 0 aborted (no space to build PCB) 0 timed out 0 dropped due to overflow 0 dropped due to bucket overflow 4 dropped due to RST 0 dropped due to ICMP unreachable 1 SYN,ACK retransmitted 1 duplicate SYN received for entries already in the cache 0 SYNs dropped (no route or no space)
The following example displays output when a TCP connection address is specified:
[local]Redback>show tcp tcb 0xe091a630
TCP Protocol Control Block at 0xe091a630: Timers: REXMT: 1430 PERSIST: 0 KEEP: 15827 2MSL: 0 State: ESTABLISHED, flags 0x38a0, inpcb 0xe090ca80 rxtshift 0, rxtcur 3, dupacks 0 peermss 498, ourmss 8152, segsz 498 snd_una 2215311423, snd_nxt 2215311425, snd_up 2215311423 snd_wl1 16681764, snd_wl2 2215311423, iss 2215310590, snd_wnd 8271 rcv_wnd 24456, rcv_nxt 16681766, rcv_up 16681764, irs 16681574 rcv_adv 16706222, snd_max 2215311425, snd_cwnd 51294, snd_ssthresh 1073725440 max_sndwnd 8466 idle 0, rtt 1, rtseq 2215311423, srtt 35, rttvar 3, rttmin 2 oobflags 0, iobc 0, softerror 0 snd_scale 0, rcv_scale 0, req_r_scale 0, req_s_scale 0 ts_recent 0, ts_regent_age 0, last_ack_sent 16681766
The following example displays the output of this command when no keywords or arguments are specified:
[local]Redback>show tcp Active Internet connections PCB Recv-Q Send-Q Local Address Foreign Address State 99e1a28 0 0 10.12.49.56.23 155.53.44.159.38903 ESTABLISHED 99e1960 0 0 10.12.49.56.23 155.53.44.159.43022 ESTABLISHED 99e1898 0 0 127.0.2.5.64524 127.0.2.3.6667 ESTABLISHED 99e17d0 0 0 127.0.2.5.56326 *.* LISTEN 99e1708 0 0 127.0.2.5.57435 127.0.2.3.6667 ESTABLISHED 99e1640 0 0 127.0.2.5.51241 127.0.2.3.6666 ESTABLISHED 99e1578 0 0 127.0.2.5.54221 127.0.2.3.6666 ESTABLISHED IP Path MTU discovery is enabled TCP keep-alive idle = 14400 TCP keep-alive interval = 150 TCP keep-alive count = 8
1.41 show tech-support
show tech-support [aaa | ase | atm | bfd | bgp | dhcp | dot1q | flowd | gre | igmp | ipv6 | isis | l2tp | ldp | mobile-ip | ospf | ospf3 | pim | ppp | pppoe | qos | rdb | snmp]
1.41.1 Purpose
Collects system information to enable customer support to resolve issues; includes both basic and module-related versions..
1.41.2 Command Mode
All modes
1.41.3 Syntax Description
aaa |
Collects Authentication, Authorization, and Accounting configuration and events |
ase |
Connects to each ASP in the system and collects debug and status information for use by technical support. |
atm |
Collects Asynchronous Transfer Mode (ATM) information |
bfd |
Collects Bidirectional Forwarding Detection (BFD) information |
bgp |
Collects Border Gateway Protocol (BGP) information |
dhcp |
Collects Dynamic Host Configuration Protocol (DHCP) server and relay information |
dot1q |
Collects 802.1Q permanent virtual circuit (PVC) information |
flowd |
Collects Flow process information for Flow Admission Control |
gre |
Collects Generic Routing Encapsulation (GRE) tunnels and tunnel circuit information |
igmp |
Collects Internet Group Management Protocol (IGMP) information |
ipv6 |
Collects IPv6 subscriber services information, concentrating on IPv6 and ND; the basic command collects data about DHCPv6 |
isis |
Collects Intermediate System-to-Intermediate System (IS-IS) routing information |
l2tp |
Collects Layer 2 Tunneling Protocol (L2TP) peer and group information |
ldp |
Collects Label Distribution Protocol (LDP) signalling information |
mobile-ip |
Collects Mobile IP information |
ospf |
Collects Open Shortest Path First (OSPF) information |
ospf3 |
Collects Open Shortest Path First (OSPF) version 3 information |
pim |
Collects Protocol Independent Multicast (PIM) information |
ppp |
Collects Point-to-Point Protocol (PPP) information |
pppoe |
Collects PPP over Ethernet (PPPoE) information |
qos |
Collects Quality of Service (QoS) information |
rdb |
Collects SmartEdge database information |
snmp |
Simple Network Management Protocol (SNMP) information |
1.41.4 Default
None
1.41.5 Usage Guidelines
Use the basic show tech-support command (without any keywords) to collect troubleshooting information for technical support; see Table 9 for the areas covered by the basic command. The output of this command must be attached to all customer support requests.
If you know that your problem is related to an ASE card or one of the modules covered by the keywords, use the command with a keyword.
To save the output in memory, use the show tech-support | save /md/filename command. Then, to send the output to a remote location, use the copy /md/filename ftp://username@hostname/filename command.
Startup and software revision |
System hardware details |
Configuration |
Core system statistics |
Process and memory status and crashes |
Core system processes |
IP routes |
Subscriber details (basic) |
Shared memory routing |
DHCPv6 |
- Note:
- By default, most show commands (in any mode) display information for the current context only or, depending on the command syntax, for all contexts. If you are an administrator for the local context, you can insert the optional context ctx-name construct before the show command to view output for the specified context without entering that context. For more information about the context ctx-name construct, see the context command description.
- Note:
- By appending a space followed by the pipe ( | ) character at the end of a show command, you can filter the output using a set of modifier keywords and arguments. For more information, see Modifying Output of show Commands in Using the CLI.
For more information on using the show tech-support command to collect troubleshooting data, see Data Collection Guideline for the SmartEdge Router.
1.41.6 Examples
- Note:
- Some commands in the show tech-support macro do not appear in the CLI and are used by customer support for troubleshooting. They are not supported for customer use outside the macro.
The following example displays entering the show tech-support command for PPP problems. For brevity, some of the command output has been truncated.
[local]Redback#show tech-support ppp [10] (ppp-debug)# term len 0 [20] (ppp-debug)# show system status process pppd History for Process: pppd Date/Time Status Message ------------------- -------------- ------- Dec 15 06:49:57.345 Starting Init Dec 15 06:49:57.574 Starting Initializing after reload Dec 15 06:49:57.712 Starting Started thread pkt-out Dec 15 06:49:57.730 Starting Started thread auth Dec 15 06:50:01.570 Starting Started thread ppp-ppa-tx_thread Dec 15 06:50:01.570 Starting Started thread worker Dec 15 06:50:01.571 Starting Sent EOF to AAA Dec 15 06:50:01.610 Starting Started thread ism Dec 15 06:50:01.615 Starting ISM FSM state: MBE-EP-up Dec 15 06:50:01.730 Starting Started thread cfg Dec 15 06:50:01.735 Starting Received EOF from RCM Dec 15 06:50:01.750 Starting Awaiting EOF from ISM Dec 15 06:50:01.840 Starting ISM FSM state: All-EP-up Dec 15 06:50:01.844 Starting Received EOF from ISM Dec 15 06:50:01.860 Starting Sent EOF to ISM Dec 15 06:50:01.860 Starting Awaiting MBE-All-EOF from ISM Dec 15 06:50:11.285 Starting Received MBE ALL EOF from ISM Dec 15 06:50:11.300 Starting Started thread ipc Dec 15 06:50:11.330 Running Ready [30] (ppp-debug)# show process ppp diagnose Current time: Thu Jan 6 08:22:47 2011 Diagnostics for ppp found no issues [40] (ppp-debug)# show process ppp chunk-statistics Elements Chunks Size InUse MaxUse Alloc Free Size InUse MaxUse Alloc Free U% Name 40 1 1 1 0 4096 1 1 1 0 1 id free list 40 3 3 3 0 40960 1 1 1 0 0 radix node 48 3 3 3 0 8192 1 1 1 0 1 ft-mc 64 35 39 114 79 8192 1 1 1 0 27 ipc 64 1 1 1 0 4096 1 1 1 0 1 pkt ... [50] (ppp-debug)# show process ppp ipc-pack-statistics Max Start Flush New Chain Per Imm. Force Flush Timer Buf ReqId Too Q Block Endpoint IPCs Msgs IPC Send Send Timer Exp. Full Flush Short Count Count -------- ------ ------ --- ----- ----- ----- ----- ----- ----- ----- ----- ----- l2tp 0 0 0 0 0 0 0 0 0 0 0 0 aaad 1 1 1 1 0 0 0 0 0 0 0 1 ism mbe 1 1 1 1 0 0 0 0 0 0 0 1 ism 2 2 1 1 0 0 0 0 0 1 0 0 pppoe 0 0 0 0 0 0 0 0 0 0 0 0 09/0 1 1 1 1 0 0 0 0 0 0 0 1 [60] (ppp-debug)# show process ppp throttle-statistics Throttle statistics for process: ppp Throttle Enabled : Yes Throttle Debug Enabled : No Throttle Active : No Min-starting : 540 Max-starting : 600 Min-authenticating : 675 Max-authenticating : 750 Min-sess-up : 540 Max-sess-up : 600 Low watemark : 90% [70] (ppp-debug)# show process ppp termination-cause [80] (ppp-debug)# show ppp counters detail Current time: Thu Jan 6 08:22:47 2011 Last cleared: Never Packet-------------------------------------------------------- In 0 Out 0 ConfReq 0 ConfReq 0 ConfAck 0 ConfAck 0 ConfNak 0 ConfNak 0 ConfRej 0 ConfRej 0 TermReq 0 TermReq 0 TermAck 0 TermAck 0 Authen Proto 0 Authen Proto 0 other 0 other 0 Session------------------------------------------------------- LCP Up 0 LCP Down 0 IPCP Up 0 IPCP Down 0 IPV6CP Up 0 IPV6CP Down 0 Authen Success 0 Authen Failure 0 Session Up 0 Session Down 0 SessionControl------------------------------------------------ Starting 0 Authenticating 0 Pended (current) 0 Pended (total) 0 Session up start 0 Packet Drop: Session pended 0 At Limit 0 Timeout------------------------------------------------------- ConfReq 0 TermReq 0 CHAP Challenge 0 UPAP Listen 0 CHAP Response 0 UPAP Request 0 Passive 0 Auto start 0 Sess phase 0 DownCause----------------------------------------------------- Rcvd TermReq 0 Rcvd PPPoE PADT 0 No ConfReq Resp 0 No Echo Resp 0 Authen Failed 0 Session Down 0 LCP Down 0 Circuit Down 0 Port Down 0 Port Delete 0 Stale Sessions 0 Circuit Unbound 0 ICR Down 0 [90] (ppp-debug)# show ppp counters debug Current time: Thu Jan 6 08:22:47 2011 Last cleared: Never Circuit/Unit---------------------------------------------------- Circuit Create 0 Circuit Delete 0 Circuit Up 0 Circuit Down 0 Unit Create 0 Unit Delete 0 Queued up msgs 0 Processed q msgs 0 Session control------------------------------------------------- Auto starting 0 Ccod starting 0 Pppoe starting 0 Tunnel starting 0 Pppoa starting 0 Sync Pkt Pended 0 Throttling state------------------------------------------------ Pppoa No Auto No System No Ccod No Pppoe No Tunnel No Max pended No Auth at max No Sess up starting No Throttling counters--------------------------------------------- auto throttle 0 ccod throttle 0 pppoa throttle 0 ism throttle 0 ism ipc blocked 0 aaa throttle 0 aaa ipc blocked 0 IPC------------------------------------------------------------- IPCs from PPPoE 0 Msgs from PPPoE 0 Bad PPPoE IPC msg 0 Bad IPC msg 0 IPCs from ISM 17 Msgs from ISM 125 IPCs from AAA 0 Msgs from AAA 0 EOF from RCM Yes EOF to ISM Yes ISM------------------------------------------------------------- EOF from ISM Yes ALL EOF from ISM Yes ISM MBE EP Up Yes ISM Client EP Up Yes ISM Client Births 1 ISM Client Deaths 0 ISM MBE Births 1 ISM MBE Deaths 0 IPv4 wait UP cplt 0 IPv6 wait UP cplt 0 Sess Up recover 0 AAA------------------------------------------------------------- Authen Req Sent 0 Authen Resp Rcvd 0 Sess Up Sent 0 Sess Down Sent 0 IPv4 Up Sent 0 IPv4 Down Sent 0 IPv6 Up Sent 0 IPv6 Down Sent 0 Verify Sub Sent 0 EOF Sent 1 Slot change Sent 0 Dropped 0 PPPoE----------------------------------------------------------- PADS rest drops 0 PADS stale drops 0 KA restart drops 0 KA ignore: sess up 0 KA stuck: down 0 KA no lcp: down 0 PPPoE sync drops 0 Timeout w/ no sync 0 L2TP----------------------------------------------------------- Tunnel start sent 0 Tunnel start rcvd 0 Tunnel stop rcvd 0 Session stop sent 0 LNS-Start no cct 0 LNS-Start no unit 0 LNS-Start rcvd 0 Unit ready sent 0 LAC-Stop no cct 0 LAC-Stop no unit 0 LAC-Stop rcvd 0 LAC verify sent 0 MP------------------------------------------------------------- Bundle sess Limit 0 Encap mismatch 0 Slot mismatch 0 Slot no support 0 Card sess Limit 0 MP neg reject 0 No MP Master 0 No MP Bundle 0 No MP Acct 0 PPA------------------------------------------------------------ Drop ctrl 0 Pass ctrl 0 Install ctx 1 Uninstall ctx 0 Msgs alloc 0 Msgs freed 0 Conf walk iter 1 Conf walk restart 0 Sent msgs 0 Recv msgs 1 Enqueued msgs 0 Dequeued msgs 0 Requeued msgs 0 Process-------------------------------------------------------- Thread Yield 0 Packet processing---------------------------------------------- LCP Creq rxmits 0 IPCP Creq rxmits 0 IPv6CP Creq rxmits 0 Buffer management statistics: enqueued 0, dequeued 0, freed 0 canceled 0, cleaned 0 ISM_In--------------------------------------------------------- ISM Statistics: Total events: ipc rcvd: 0, ipc err 0, unknown event 0 ID: I/F : state 47, cfg 25, IP cfg 21, Cct : state 0, Cct cfg 0, Cct grp 0 Port : state 2, Port cfg 0 Lg : cfg 0 L2tp : sesscfg 0 Hdr : only 1 GrpMac: cfg 0 Card : state 8 Peer : 0 CCT SUBID: down 0, up 0, create 0, del 0, par_up 0 CFG: eth 0, ocn 0, 1q 0, tun 0, fr 0, ppp 0 atm 0, lm 0, l2tp 0, cfg 0 SUB: clear 0, down 0, down_cplt 0 GRP: join 0, leave 0 I/F SUBID: down 10, up 15, create 11, del 0, bind 11, unbind 0 CFG: cfg 25, ipcfg 21 PORT SUBID: down 2, up 0, del 0 CFG: eth 0, stsn 0 LG SUBID: grp cfg 0, ungrp cfg 0, prot grp cfg 0 prot cct cfg 0, prot grp action 0 L2TPSESS SUBID: cfg 0 GRPMAC: UCAST: reg 0, dereg 0 MCAST: reg 0, dereg 0 CARD SUBID: create 2, down 0, up 2, del 0 rate cfg 1, mic 0 ISM_Out-------------------------------------------------------- ISM Statistics: Total events: ipc rcvd: 0, ipc err 0, unknown event 0 ID: I/F : state 0, cfg 0, IP cfg 0, Cct : state 0, Cct cfg 0, Cct grp 0 Port : state 0, Port cfg 0 Lg : cfg 0 L2tp : sesscfg 0 Hdr : only 0 GrpMac: cfg 0 Card : state 0 Peer : 0 CCT SUBID: down 0, up 0, create 0, del 0, par_up 0 CFG: eth 0, ocn 0, 1q 0, tun 0, fr 0, ppp 0 atm 0, lm 0, l2tp 0, cfg 0 SUB: clear 0, down 0, down_cplt 0 GRP: join 0, leave 0 I/F SUBID: down 0, up 0, create 0, del 0, bind 0, unbind 0 CFG: cfg 0, ipcfg 0 PORT SUBID: down 0, up 0, del 0 CFG: eth 0, stsn 0 LG SUBID: grp cfg 0, ungrp cfg 0, prot grp cfg 0 prot cct cfg 0, prot grp action 0 L2TPSESS SUBID: cfg 0 GRPMAC: UCAST: reg 0, dereg 0 MCAST: reg 0, dereg 0 CARD SUBID: create 0, down 0, up 0, del 0 rate cfg 0, mic 0 [100] (ppp-debug)# show ppp counters all-contexts Context :local Context id : 0x40080001 ------------------------------------------------------------------ Last cleared: Never received: bytes 0, packets 0, unsupported packets 0 sent: bytes 0, packets 0 LCP echo request : received 0, sent 0, dropped 0 LCP echo response : received 0, sent 0, dropped 0 LCP protocol reject : received 0, sent 0, dropped 0 Context :two Context id : 0x40080003 ------------------------------------------------------------------ Last cleared: Never received: bytes 0, packets 0, unsupported packets 0 sent: bytes 0, packets 0 LCP echo request : received 0, sent 0, dropped 0 LCP echo response : received 0, sent 0, dropped 0 LCP protocol reject : received 0, sent 0, dropped 0 Context :three Context id : 0x40080004 ... [110] (ppp-debug)# show ppp summary all [120] (ppp-debug)# show ppp multilink summary Bundle Count = 0, Link Count = 0 Total Bundles = 0, Total Links = 0 [130] (ppp-debug)# show ppp global fast disconnect : No pppoe large mru : No pppoe-src-mac vld : No pppoe send-padt : No sub MP enabled : No sync control : No LCP no padt : No disc no peer-ip : No Our MP ED set : No send ipv6cp-creq : No max conf reqs : 11 our init mru : 1500 our max mru : 12800 peer min mru : 256 peer max mru : 12800 delay lcp-confreq : 3 (secs) [140] (ppp-debug)# show log | grep "PPP-" [150] (ppp-debug)# show proc ppp detail Process (PID) : ppp (1934) Spawn count : 1 Memory : 7172K Time : 00:04:05.08 %CPU : 0.00% State : run Up time : 3w1d Heart beat : Enabled Spawn time : 2 seconds Max crashes allowed : 5 Crash thresh time : 86400 seconds Total crashes : 0 Fast restart : DISABLED Critical process : NO / NO Images: (Spawns, Max spawns, Version, Path) (*) 1, 4, v1, /usr/siara/bin/pppd Client IPC Endpoints: EP 7f000205 f2640006 - PPP SLOT 09/0:00000000 EP 7f000205 f264000a - PPPOE-IPC-EP-NAME:00000000 EP 7f000205 f2640008 - ISM2-CLIENT-EP-NAME:00000000 EP 7f000205 f2640008 - ISM2-MBE-EVIN-EP-NAME:00000000 EP 7f000205 f2640005 - AAA-IPC-MSG-EP-NAME:00000000 EP 7f000205 f2640005 - L2TP-PPP-EP-NAME:00000000 Server IPC Endpoints: EP 7f000205 f264000a - PPP-IPC-EP-NAME:00000000 Dependent process pppoe (1938) EP 7f000205 e6820007 Dependent process l2tp (1873) EP 7f000205 f94d0005 Dependent process IPPA IPC SLOT 9 (-2146893823) EP 7f000a09 0001001e EP 7f000205 f2640009 - PPP-CONF-EP-NAME:00000000 Dependent process rcm (1846) EP 7f000205 e8ac0001 EP 7f000205 f2640008 - PPP-ISM-EP-NAME:00000000 Dependent process ism (1848) EP 7f000205 ddab000c Dependent process ism (1848) EP 7f000205 ddab000a EP 7f000205 f2640005 - PPP-AUTH-EP-NAME:00000000 Dependent process aaad (1964) EP 7f000205 f5d70009
1.42 show terminal
show terminal
1.42.1 Purpose
Displays terminal settings for the current session.
1.42.2 Command Mode
All modes
1.42.3 Syntax Description
This command has no keywords or arguments.
1.42.4 Default
None
1.42.5 Usage Guidelines
Use the show terminal command to display terminal settings for the current session.
- Note:
- By appending a space followed by the pipe ( | ) character at the end of a show command, you can filter the output using a set of modifier keywords and arguments. For more information, see Modifying Output of show Commands in Using the CLI.
1.42.6 Examples
The following example displays the terminal settings for the current session:
[local]Redback>show terminal terminal name = /dev/ttyp0 terminal width = 98 terminal length = 50 terminal monitor = disabled
1.43 show transaction
show transaction
1.43.1 Purpose
Displays information about outstanding configuration database transactions made by other administrators in all configuration modes or created by internal processes.
1.43.2 Command Mode
All modes
1.43.3 Syntax Description
This command has no keywords or arguments.
1.43.4 Default
None
1.43.5 Usage Guidelines
Use the show transaction command to display information about outstanding configuration database transactions made by other administrators in all configuration modes, or created by internal processes. Outstanding transactions are those that have been configured by other administrators or started by an internal process, but have not yet been committed to the configuration database. Table 10 lists the possible states that might be displayed for a transaction.
State |
Description |
---|---|
Active |
Transaction is active for configuration changes. |
Ready |
Transaction just got the lock it was waiting for and is ready to proceed. |
Blocked |
Transaction is blocked waiting for a lock. The information field displays the transaction ID that holds the lock. |
Blocked on User |
Transaction is blocked by administrator input on whether to continue waiting for the lock to clear. The information field displays the transaction ID that holds the lock. |
Pending Rollback |
Administrator has requested to stop waiting for the lock and the system is preparing to rollback the current command. |
Abort |
Transaction is being erased. |
Committing |
Transaction is marked for commit. |
Commit - Duplicated |
Transaction is duplicated to the standby controller card. (1) |
Commit - Duplicated |
Transaction is duplicated to the standby controller card. |
Commit - Synched |
Transaction is committed on the standby controller card.(2) |
Commit - Synched |
Transaction is committed on the standby controller card. |
Committed |
Transaction has completed the committing on the active controller card. |
Commit - Blocked |
Commit is held up because of a global database lock. Waiting to commit after the lock is clear. |
Waiting to Commit |
Transaction has been time committed. It will be committed at a certain time. The information field displays the time until the commit. |
Invalid |
Transaction is invalid. |
(1) The SmartEdge 100 router has a single controller
card. The Commit-Duplicated and Commit-Synched transaction
states apply only to SmartEdge routers with dual controller cards.
(2) The SmartEdge 100 router has a single controller
card. The Commit-Duplicated and Commit-Synched transaction
states apply only to SmartEdge routers with dual controller cards.
- Note:
- By default, most show commands (in any mode) display information for the current context only or, depending on the command syntax, for all contexts. If you are an administrator for the local context, you can insert the optional context ctx-name construct before the show command to view output for the specified context without entering that context. For more information about the context ctx-name construct, see the context command description.
- Note:
- By appending a space followed by the pipe ( | ) character at the end of a show command, you can filter the output using a set of modifier keywords and arguments. For more information, see Modifying Output of show Commands in Using the CLI.
1.43.6 Examples
The following example shows the outstanding database transactions created, but not committed, by the admin, admin1, and admin2 administrators:
[local]Redback>show transaction
TID State Sequence State Information User Comment --------------------------------------------------------------------- 1037 Blocked 73544 Waiting on TID 1035 admin1 adding circuit under port 1 1035 Active 3634 None admin1 changing port 1 1032 Commit - Duplicated 564654 None admin1 1026 Waiting to Commit 2343564 Committing in 25 min admin adding admin2 at midnight 1022 Active 565 None admin 1011 Abort 84454 None admin deleting admin2
1.44 show tunnel
To show information about Generic Routing Encapsulation (GRE) tunnels, the syntax is:
show tunnel gre [name tunl-name | peer peer-name | remote remote-IP] [detail]
To show information about IP-in-IP tunnels, the syntax is:
show tunnel ipip [name tunl-name | remote remote-IP] [detail]
To show information about automatic IP Version 6 (IPv6) tunnels, the syntax is:
show tunnel ipv6-auto [name tunl-name | remote remote-IP] [detail]
To show information about manual IPv6 tunnels, the syntax is:
show tunnel ipv6-manual [name tunl-name | remote remote-IP] [detail]
1.44.1 Purpose
Displays information about tunnels currently configured in the SmartEdge router.
1.44.2 Command Mode
all modes
1.44.3 Syntax Description
gre |
Displays information for GRE tunnels. |
ipip |
Displays information for IP-in-IP tunnels |
ipv6-auto |
Displays information for automatic IPv6 tunnels. |
ipv6-manual |
Displays information for manual IPv6 tunnels. |
name tunl-name |
Optional. The name of the tunnel for which information is displayed. |
peer peer-name |
Optional. The name of the GRE peer for which information is displayed. |
remote remote-IP |
Optional. The IP address of the remote interface to a tunnel for which information is displayed. |
detail |
Optional. Specifies the output provides fullest details. |
1.44.4 Default
When the tunnel type is specifed, but the name, remote address. and peer name are not specified, all tunnels of that type are displayed.
1.44.5 Usage Guidelines
Use the show tunnel command to display information about tunnels currently configured in the SmartEdge router. Use the show tunnel client command on Section 1.45 to find information about dynamic tunnel clients that are registered with the tunnel manager.
The following fields can appear in the output of the show tunnel command.
Field |
Description |
---|---|
Name |
Name of the tunnel. |
Context |
Context in which the tunnel was created. |
Type |
IPv6-auto, IPv6-manual, IP-in-IP, or GRE tunnel. |
MTU |
MTU of tunnel. |
Local IP |
Local IP address of the tunnel. |
Remote IP |
Remote IP address of the tunnel. |
State |
The tunnel states can be:
|
Bound to |
Interface and context to which tunnel circuit is bound. |
(1) If the GRE tunnel has no circuits configured, the state is always
down, even after you have entered the no shutdown command
(in GRE peer configuration mode).
Use the uptime keyword to display the amount of time the tunnel circuit is in the Up state.
- Note:
- By default, most show commands (in any mode) display information for the current context only or, depending on the command syntax, for all contexts. If you are an administrator for the local context, you can insert the optional context ctx-name construct, preceding the show command, to view output for the specified context without entering that context. For more information about using the context ctx-name construct, see the context command description.
- Note:
- By appending a space followed by the pipe ( | ) character at the end of a show command, you can filter the output using a set of modifier keywords and arguments. For more information, see Modifying Output of show Commands in Using the CLI.
1.44.6 Examples
(Example 1) The following example shows how to display information for the GRE peer named toBoston:
[local]Redback>show tunnel gre peer toBoston
Name Context Type MTU Local-IP Remote-IP State toBoston local gre 1468 11.1.1.1 11.1.1.1 Down
(Example 2) The following example shows how to display detailed information for the toChicago GRE tunnel in the local context:
[local]Redback>show tunnel name gre toChicago detail ::::: Tunnel : toChicago Key : - Remote IP : 2.2.2.2 Local IP : 192.168.1.5 Tnl Type : GRE State : Down Bound to : Circuit ID: 1 Internal Hdl: 255/4:1023:63/0/1/1 Tunnel is User Configured local-ip 192.168.1.5, context-for-local-ip: local mtu 1468 log-state-changes no clear-df no Keep-alive 0 seconds, retries 0 destination DOWN on nhop mgmt interface resolved on grid 0x10000000 Tunnel ID: gre 1 Circuit ID Internal: 255/4:1023:63/0/1/1
1.45 show tunnel client
show tunnel client client-name [context ctx-name] [detail]
1.45.1 Purpose
Displays information about dynamic tunnel clients that are registered with the tunnel manager.
1.45.2 Command Mode
All modes
1.45.3 Syntax Description
client-name |
Name of client. |
context ctx-name |
Optional. Name of context. |
detail |
Optional. Displays detailed information about dynamic tunnel clients that are registered with the tunnel manager. |
1.45.4 Default
When entered without any optional syntax, the show tunnel client command displays all dynamic tunnel clients that are registered with the tunnel manager.
1.45.5 Usage Guidelines
Use the show tunnel client command to information about dynamic tunnel clients registered with the tunnel manager.
- Note:
- By default, most show commands (in any mode) display information for the current context only or, depending on the command syntax, for all contexts. If you are an administrator for the local context, you can insert the optional context ctx-name construct, preceding the show command, to view output for the specified context without entering that context. For more information about using the context ctx-name construct, see the context command description.
- Note:
- By appending a space followed by the pipe ( | ) character at the end of a show command, you can filter the output using a set of modifier keywords and arguments. For more information, see Modifying Output of show Commands in Using the CLI.
1.45.6 Examples
The following example shows how to display information about all dynamic tunnel clients that are registered with the tunnel manager in all contexts:
[local]Redback>show tunnel client Tunnel client information summary --------------------------------------------------------- Client Name : mobile-ip (client-id 2 Context Name : local IPIP Tunnel Count : 0 GRE Tunnel Count : 0 Register State : Registered Restart State : Alive --------------------------------------------------------- Client Name : mobile-ip (client-id 2) Context Name : fa-ctx IPIP Tunnel Count : 0 GRE Tunnel Count : 0 Register State : Registered Restart State : Alive
The following example shows how to display information about dynamic tunnel client named mobile-ip in all contexts that it has registered with tunnel manager:
[local]Redback>show tunnel client mobile-ip Tunnel client information summary --------------------------------------------------------- Client Name : mobile-ip (client-id 2) Context Name : local IPIP Tunnel Count : 0 GRE Tunnel Count : 0 Register State : Registered Restart State : Alive --------------------------------------------------------- Client Name : mobile-ip (client-id 2) Context Name : fa-ctx IPIP Tunnel Count : 0 GRE Tunnel Count : 0 Register State : Registered Restart State : Alive
The following example shows how to display information about dynamic tunnel client named mobile-ip, that is registered with the tunnel manager in the fa-ctx context:
[local]Redback>show tunnel client mobile-ip context fa-ctx Tunnel client information summary --------------------------------------------------------- Client Name : mobile-ip (client-id 2) Context Name : fa-ctx IPIP Tunnel Count : 0 GRE Tunnel Count : 0 Register State : Registered Restart State : Alive
The following example shows how to display detailed information tunnel information about all dynamic tunnel clients that are registered with the tunnel manager in all contexts:
[local]Redback>show tunnel client detail Tunnel client detailed information --------------------------------------------------------- Client Name : mobile-ip (client-id 2) Context Name : local IPIP Tunnel Count : 0 GRE Tunnel Count : 0 Register State : Registered Restart State : Alive Counters Registration requests received : 1 Deregistration requests received : 0 Reregistration requests received : 0 Tunnel add requests received : 0 Tunnel delete requests received : 0 Tunnel modify requests received : 0 Tunnel verify requests received : 0 Tunnel registration responses sent : 0 Client information responses sent : 0 Tunnel verification responses sent : 0 Failed to get state - no client : 0 Invalid config requests received : 0 Reg info req rcvd no client : 0 Client free fail bad client id : 0 Client add fail-bad client id : 0 Client add fail-no memory : 0 Client add fail-due to tree insert : 0 Client add fail-no id available : 0 Client add fail-duplicate insert : 0 Reg resp not sent not registered : 0 Reg resp not sent no memory : 0 Client info not sent-not registered : 0 Client info not sent-no memory : 0 Client IPC xmit queue count : 0 --------------------------------------------------------- Client Name : mobile-ip (client-id 2) Context Name : fa-ctx IPIP Tunnel Count : 0 GRE Tunnel Count : 0 Register State : Registered Restart State : Alive Counters Registration requests received : 1 Deregistration requests received : 0 Reregistration requests received : 0 Tunnel add requests received : 0 Tunnel delete requests received : 0 Tunnel modify requests received : 0 Tunnel verify requests received : 0 Tunnel registration responses sent : 0 Client information responses sent : 0 Tunnel verification responses sent : 0 Failed to get state - no client : 0 Invalid config requests received : 0 Reg info req rcvd no client : 0 Client free fail bad client id : 0 Client add fail-bad client id : 0 Client add fail-no memory : 0 Client add fail-due to tree insert : 0 Client add fail-no id available : 0 Client add fail-duplicate insert : 0 Reg resp not sent not registered : 0 Reg resp not sent no memory : 0 Client info not sent-not registered : 0 Client info not sent-no memory : 0 Client IPC xmit queue count : 0
1.46 show udp
show udp {sockets | statistics}
1.46.1 Purpose
Displays User Datagram Protocol (UDP) socket and statistical information.
1.46.2 Command Mode
all modes
1.46.3 Syntax Description
sockets |
Displays UDP socket information. |
statistics |
Displays UDP statistics. |
1.46.4 Default
None
1.46.5 Usage Guidelines
Use the show udp command to display UDP socket and statistical information.
- Note:
- By default, most show commands (in any mode) display information for the current context only or, depending on the command syntax, for all contexts. If you are an administrator for the local context, you can insert the optional context ctx-name construct before the show command to view output for the specified context without entering that context. For more information about the context ctx-name construct, see the context command description.
- Note:
- By appending a space followed by the pipe ( | ) character at the end of a show command, you can filter the output using a set of modifier keywords and arguments. For more information, see Modifying Output of show Commands in Using the CLI.
1.46.6 Examples
The following example displays output when the statistics keyword is specified:
[local]Redback>show udp statistics
udp: 95808 datagrams received 0 with incomplete header 0 with bad data length field 0 with bad checksum 875 dropped due to no socket 94931 broadcast/multicast datagrams dropped due to no socket 0 dropped due to full socket buffers 2 delivered 875 PCB hash misses 875 datagrams output
The following example displays output when the sockets keyword is specified:
[local]Redback>show udp sockets
Active Internet connections (including servers) PCB Recv-Q Send-Q Local Address Foreign Address f07cbb80 0 0 127.0.0.1.64721 *.* vc f07cb958 0 0 127.0.0.1.64741 *.* f07cb8a0 0 0 127.0.0.1.64746 *.* f07cbcf0 0 0 127.0.0.1.64773 *.* f07cb730 0 0 127.0.0.1.64790 *.* f07cbc38 0 0 127.0.0.1.64876 *.* f07cba6c 0 0 127.0.0.1.123 *.* f07cb7e8 0 0 127.0.0.1.64914 *.* f07cb78c 0 0 127.0.0.1.64915 *.* f07cb6d4 0 0 127.0.0.1.64917 *.* f07cb678 0 0 127.0.0.1.64918 *.* f07cbbdc 0 0 127.0.0.1.64919 *.* f07cbe60 0 0 127.0.0.1.64920 *.* f07cbf18 0 0 127.0.0.1.64921 *.* f07cbf74 0 0 127.0.0.1.64922 *.* f07cbebc 0 0 127.0.0.1.6000 *.*
1.47 show version
show version
1.47.1 Purpose
Displays the current version of the software running on the system.
1.47.2 Command Mode
All modes
1.47.3 Syntax Description
This command has no keywords or arguments.
1.47.4 Default
None
1.47.5 Usage Guidelines
Use the show version command to display the current version of the software running on the system.
For the SmartEdge 100 router with one or both ATM OC media interface cards (MICs), the command output includes, at or near its end, several lines dedicated to the MICs.
- Note:
- By default, most show commands (in any mode) display information for the current context only or, depending on the command syntax, for all contexts. If you are an administrator for the local context, you can insert the optional context ctx-name construct before the show command to view output for the specified context without entering that context. For more information about the context ctx-name construct, see the context command description.
- Note:
- By appending a space followed by the pipe ( | ) character at the end of a show command, you can filter the output using a set of modifier keywords and arguments. For more information, see Modifying Output of show Commands in Using the CLI.
1.47.6 Examples
The following example displays output from the show version command:
[local]Redback>show version
Redback Networks SmartEdge OS Version SEOS-5.0.5-Release Built by sysbuild@@lx-lsf159Fri Jan 27 01:30:02 PST 2006 Copyright (C) 1998-2006, Redback Networks Inc. All rights reserved. System Bootstrap version is PowerPC,1.0b1267 Installed minikernel version is 20 Router Up Time - 22 hours 1 minute 18 secs
The following example displays output from the show version command for a SmartEdge 100 router with one ATM OC3 MIC installed in slot 2. The MIC manufacturing information in the next line gives the Redback copyright notice:
[local]Redback#show version Redback Networks SmartEdge OS Version SEOS-7.0.0.0-Release Built by sysbuildd@lx-lsf401 Wed Nov 22 10:05:57 PST 2006 Copyright (C) 1998-2006,Redback Networks Inc. All rights reserved. System Bootstrap version is PowerPC,rev2.0.1.2 Installed minikernel version is 2.6 ... Linecard 2 MIC _mic_ sarc Version SEOS-7.0.0.0-Release Built by sysbuildd@lx-lsf401 Wed Nov 22 10:21:45 PST 2006 Copyright (C) 1998-2006,Redback Networks Inc. All rights reserved. Router Up Time - 3 minutes 42 secs
1.48 show vpls
show vpls [bridge-name] [detail]
1.48.1 Purpose
Displays Virtual Private LAN Services (VPLS)-enabled bridge information.
1.48.2 Command Mode
all modes
1.48.3 Syntax Description
bridge-name |
Optional. Name of the VPLS-enabled bridge instance name. Displays information for the specified bridge instance. |
detail |
Optional. Displays detailed information. |
1.48.4 Default
None
1.48.5 Usage Guidelines
Use the show vpls command to display VPLS-enabled bridge information.
- Note:
- By default, most show commands (in any mode) display information for the current context only or, depending on the command syntax, for all contexts. If you are an administrator for the local context, you can insert the optional context ctx-name construct, preceding the show command, to view output for the specified context without entering that context. For more information about using the context ctx-name construct, see the context command description.
- Note:
- By appending a space followed by the pipe ( | ) character at the end of a show command, you can filter the output using a set of modifier keywords and arguments. For more information, see Modifying Output of show Commands in Using the CLI. For information about troubleshooting VPLS, see Troubleshooting VPLS.
1.48.6 Examples
The following example displays output from the show vpls command:
[local]Redback>show vpls
VPLS Bridge Pseudo-wire ID Peers(Up) State BridgeName 1 1(1 ) Enable
The following example displays output from the show vpls detail command:
[local]Redback>show vpls detail VPLS instance name : vplsA Context name : local Admin state : Enable Bridge identifier : 0x1 Context identifier : 0x40080001 Default PW-identifier : <none> Number of peers : 1 (Up:1, hub:1, spoke:0) Number of standby peers : 1 (local PE-rs) 0 (local MTU-s)
1.49 show vpls peer
To display Virtual Private LAN Services (VPLS) peer information for a specific bridge, the syntax is:
show vpls bridge-name peer [ip-addr | profile prof-name | pw-id pw-num | pw-name pw-name] [detail]
To display VPLS peer information for all bridges, the syntax is:
show vpls peer ip-addr {pw-id pw-num | pw-name pw-name} [detail]
1.49.1 Purpose
Displays VPLS peer information.
1.49.2 Command Mode
all modes
1.49.3 Syntax Description
bridge-name |
VPLS-enabled bridge instance name. Displays information for the VPLS peers on the specified bridge instance. |
ip-addr |
VPLS peer IP address in the form A.B.C.D. Displays information for the specified VPLS peer. Optional when displaying peer information for a specific bridge. |
profile prof-name |
VPLS profile name. Displays information for the VPLS peers in the specified VPLS profile. Optional when displaying peer information for a specific bridge. |
pw-id pw-num |
Pseudo-wire number. Displays information for the VPLS peers that use the specified pseudo-wire number. Optional when displaying peer information for a specific bridge. |
pw-name pw-name |
Pseudo-wire name. Displays information for the VPLS peers that use the specified pseudo-wire name. Optional when displaying peer information for a specific bridge. |
detail |
Optional. Displays detailed information. |
1.49.4 Default
None
1.49.5 Usage Guidelines
Use the show vpls peer command to display VPLS peer information.
When the root command is used without any additional syntax, information for all the VPLS peer instances is displayed. If additional syntax is used to match a single VPLS peer instance, then the detailed version of the output is displayed. If additional syntax is used to help filter the set of VPLS peers, then the brief version of the output is displayed.
- Note:
- By default, most show commands (in any mode) display information for the current context only or, depending on the command syntax, for all contexts. If you are an administrator for the local context, you can insert the optional context ctx-name construct, preceding the show command, to view output for the specified context without entering that context. For more information about using the context ctx-name construct, see the context command description.
- Note:
- By appending a space followed by the pipe ( | ) character at the end of a show command, you can filter the output using a set of modifier keywords and arguments. For more information, see Modifying Output of show Commands in Using the CLI. For information about troubleshooting VPLS, see Troubleshooting VPLS
Table 12 describes the show vpls peer command output fields.
Field |
Description |
---|---|
Admin state |
Computed administrative state for the peer:
|
Bridge id |
System-generated bridge ID. |
Circ cfg changes |
Circuit configuration change count. |
Circ delete cnt |
Circuit delete count. |
Circ error cnt |
Circuit error count. |
Circ up/down cnt |
Circuit up and down count. |
Circuit ID |
Circuit ID, represented as VPLS circuit-id, which is used by a peer in the system. A circuit is allocated for each peer, except standby peers. A standby peer uses the circuit associated with the primary peer on switchover. |
Context id |
Context ID. |
Context name |
Name of the context in which VPLS is configured. |
Last error |
Last error logged by the system:
|
MAC flush received |
MAC flush received count. |
MAC flush sent |
MAC flush sent count. |
Oper State/State |
Operational state of the peer:
|
PE local mode |
Local mode of operation for the neighbor connection:
|
PE peering Type/Type |
VPLS peering type:
This field describes the configuration, and not necessarily the operation state. |
Peer config changes |
Peer configuration change count. |
Peer flags |
Run-time bit flags maintained by a peer to capture the state as it understands it:
|
| |
Peer ID |
VPLS peer ID, which is the neighbor IP address. |
Peer proc restarts |
Peer process restart count. |
Peer reset cnt |
Peer reset count. |
Peer restart cnt |
Peer restart count. |
Peer state changes |
Peer state change count. |
Peer up/down cnt |
Peer up and down count. |
Prev event |
Previous peer flag event:
|
Prev state |
Previous operational state:
|
Primary PE |
Primary neighbor’s IP address. |
Primary PE state |
Primary neighbor’s operational state. For more information about the values for this field, see the Prev State field. |
Profile name |
VPLS profile name. |
Pseudo-wire ID |
Pseudo-wire ID. The ID can be the pseudo-wire name or number. |
PW encap type |
Pseudo-wire encapsulation type:
|
PW error cnt |
Pseudo-wire error count. |
PW exp bits |
Pseudo-wire EXP bits. |
PW flags |
Run-time bit flags maintained by a peer for a pseudo-wire:
|
PW In label |
MPLS label used for packets received over the pseudo-wire. |
PW local MTU |
Pseudo-wire local MTU. |
PW Out label |
MPLS label used for packets transmitted over the pseudo-wire. |
PW remote MTU |
Pseudo-wire remote MTU. |
PW restart cnt |
Pseudo-wire restart count. |
PW state |
Pseudo-wire state:
|
PW up/down cnt |
Pseudo-wire up and down count. |
Standby PE |
Standby neighbor’s IP address. |
Standby PE state |
Standby neighbor’s operational state. For more information about the values for this field, see the Prev State field. |
VPLS Bridge |
VPLS bridge name. |
VPLS peer |
VPLS peer is uniquely identified by the following three values:
|
(1) If the process
restart occurred when a standby peer was operational, then the states
for the primary and standby peers are recovered.
1.49.6 Examples
The following example displays output from the show vpls peer command:
[local]Redback>show vpls peer VPLS Bridge Peer ID Pseudo-wire ID Circuit ID Type State corpA 22.22.22.22 100 VPLS 3 Hub Up corpA 33.33.33.33 100 VPLS 4 Hub Up corpA 55.55.55.55 100 VPLS 6 Sp Up
The following example displays output from the show vpls peer command:
[local]Redback>show vpls peer detail VPLS peer (bridge/ip:pwid): vplsA/22.22.22.22:10 Oper State : Up Context name : local Admin State : Enable Circuit id : VPLS 3 Peer Flags : active, pw-up Bridge id : 0x1 Context id : 0x40080001 PE peering type : Hub PE local mode : PE-rs Prev state : Down Profile name : forvplsA Prev event : pw-up Last error : no error PW state : Up, Active PW up/down cnt : 1 PW error cn : 0 PW restart cnt : 1 PW In label : 131072 PW encap type : Ethernet PW Out label : 131072 PW Exp bits : 0x0 PW local MTU : 1500 PW remote MTU : 1500 PW flags : in-rib, in-lblmap, in-ldp, from-ldp, from-cfg, ism-up, peer-up
The following example displays output from the show vpls peer command when primary and standby neighbors are configured:
[local]Redback>show vpls peer VPLS Bridge Peer ID Pseudo-wire ID Circuit ID Type State corpA-MTU 11.11.11.11 100 VPLS 3 Sp Pri Up corpA-MTU 33.33.33.33 100 VPLS 3 Sp Sby Stby
The following example displays output from the show vpls peer detail command when primary and standby neighbors are configured:
[local]Redback>show vpls peer detail VPLS peer (bridge/ip:pwid): corpA-MTU/11.11.11.11:100 Oper State : Up Context name : local Admin State : Enable Circuit id : VPLS 1 Peer Flags : pri, active, pw-up Bridge id : 0x1 Context id : 0x40080001 PE peering type : Spoke PE local mode : MTU-s Standby PE : 33.33.33.33 Standby PE state : Stby Prev state : Down Profile name : p1 Prev event : cct-cfg-change Last error : no error Peer up/down cnt : 1 Peer state changes : 2 Peer reset cnt : 0 Peer config changes : 0 Peer restart cnt : 0 Peer proc restarts : 0 MAC flush sent : 0 MAC flush received : 0 Circ up/down cnt : 0 Circ cfg changes : 2 Circ error cnt : 0 Circ delete cnt : 0 PW state : Up, Active PW up/down cnt : 1 PW error cnt : 0 PW restart cnt : 1 PW In label : 131072 PW encap type : Ethernet PW Out label : 131072 PW Exp bits : 0x0 PW local MTU : 1500 PW remote MTU : 1500 PW flags : in-rib, in-lblmap, in-ldp, from-ldp, from-cfg peer-up VPLS peer (bridge/ip:pwid): corpA-MTU/33.33.33.33:100 Oper State : Stby Context name : local Admin State : Enable Circuit id : VPLS 1 Peer Flags : stby, pw-up Bridge id : 0x1 Context id : 0x40080001 PE peering type : Spoke PE local mode : MTU-s Primary PE : 11.11.11.11 Primary PE state : Up Prev state : Down Profile name : p1 Prev event : pw-up Last error : no error Peer up/down cnt : 0 Peer state changes : 2 Peer reset cnt : 0 Peer config changes : 0 Peer restart cnt : 0 Peer proc restarts : 0 MAC flush sent : 0 MAC flush received : 0 Circ up/down cnt : 0 Circ cfg changes : 0 Circ error cnt : 0 Circ delete cnt : 0 PW state : Down, Standby, In-active PW up/down cnt : 1 PW error cnt : 0 PW restart cnt : 1 PW In label : 131073 PW encap type : Ethernet PW Out label : 131072 PW Exp bits : 0x0 PW local MTU : 1500 PW remote MTU : 1500 PW flags : in-lblmap, in-ldp, from-ldp, from-cfg peer-up
1.50 show vpls profile
show vpls profile [prof-name [pe ip-addr]] [detail]
1.50.1 Purpose
Displays Virtual Private LAN Services (VPLS) profile information.
1.50.2 Command Mode
all modes
1.50.3 Syntax Description
prof-name |
Optional. VPLS profile name. Displays information for the specified VPLS profile. |
pe ip-addr |
Optional. VPLS neighbor IP address in the form A.B.C.D. Displays VPLS profile information for the specified VPLS peer. |
detail |
Optional. Displays detailed information. |
1.50.4 Default
None
1.50.5 Usage Guidelines
Use the show vpls profile command to display VPLS profile information.
- Note:
- By default, most show commands (in any mode) display information for the current context only or, depending on the command syntax, for all contexts. If you are an administrator for the local context, you can insert the optional context ctx-name construct, preceding the show command, to view output for the specified context without entering that context. For more information about using the context ctx-name construct, see the context command description.
- Note:
- By appending a space followed by the pipe ( | ) character at the end of a show command, you can filter the output using a set of modifier keywords and arguments. For more information, see Modifying Output of show Commands in Using the CLI. For information about troubleshooting VPLS, see Troubleshooting VPLS.
1.50.6 Examples
The following example displays output from the show vpls profile command:
[local]Redback>show vpls profile
VPLS Profile PE ID Bridge Profile Type Peers(Up) test 1.2.1.1 Hub 1 (1) test 1.2.1.2 Hub 1 (1)
The following example displays output from the show vpls profile detail command:
[local]Redback>show vpls profile detail VPLS profile (name/pe-id) : test/1.2.1.1 PE peering type : Hub PE local mode : PE-rs Number of peers : 1 Active peers : 1 Standby for : none Bridge profile : forvplsA Enacp type : Ethernet MAC limit : 16002 Bcast rate-limit : 0 Bcast burst-size : 1 Mcast rate-limit : 1 Mcast burst-size : 0 Unknown rate-limit : 0 Unknown burst-size : 0 Bridge flags : 0x8004
1.51 show vrrp
show vrrp [debug | routers [if-name [vrrp-id]] | statistics [if-name [vrrp-id]]
1.51.1 Purpose
Displays Virtual Router Redundancy Protocol (VRRP) information.
1.51.2 Command Mode
all modes
1.51.3 Syntax Description
debug |
Optional. Displays debug options and filters. |
routers |
Optional. Displays state information pertaining to virtual routers. |
if-name |
Optional. Interface name. Displays the specified information for only the named interface. |
vrrp-id |
Optional. Virtual router ID. The range of values is 1 to 255. Displays the specified information for only the VRRP ID indicated. |
statistics |
Optional. Displays VRRP statistics. |
1.51.4 Default
When entered without specifying any options, this command displays all VRRP statistics information.
1.51.5 Usage Guidelines
Use the show vrrp command to display VRRP information. Router and statistics information may be limited to virtual routers on a single interface or a single virtual router on a single interface.
- Note:
- By default, most show commands (in any mode) display information for the current context only or, depending on the command syntax, for all contexts. If you are an administrator for the local context, you can insert the optional context ctx-name construct, preceding the show command, to view output for the specified context without entering that context. For more information about using the context ctx-name construct, see the context command description.
- Note:
- By appending a space followed by the pipe ( | ) character at the end of a show command, you can filter the output using a set of modifier keywords and arguments. For more information, see Modifying Output of show Commands in Using the CLI.
1.51.6 Examples
The following example displays output from the show vrrp command:
[local]Redback>show vrrp
--- VRRP Virtual Router vrrp1/2 (Backup) --- State : Backup Last Event : Interface Up Priority : 100 Advertise Int : 22 Last Adv Source : 0.0.0.0 Up Time : 5d 05:24:04 Preempt : No Master Down Int : 66 Skew Time (u-sec) : 218750 Auth Type: : None Key Chain : Address List: 1.1.1.1 --- VRRP Virtual Router vrrp1/3 (Backup) --- State : Init Last Event : None Priority : 100 Advertise Int : 1 Last Adv Source : 0.0.0.0 Up Time : N/A Preempt : No Master Down Int : 3 Skew Time (u-sec) : 609375 Auth Type: : None Key Chain : Address List: 2.2.2.2
The following example displays output from the show vrrp statistics command:
[local]Redback>show vrrp statistics
--- VRRP Global Statistics --- Virtual Routers : 3 Interfaces : 1 Packets Sent : 0 Packets Received : 0 Packet Dropped : 0 No Router Errors : 0 Checksum Errors : 0 Version Errors : 0 --- VRRP Virtual Router vrrp1/1 (Backup) --- Master Transitions: 0 Advertisement Recv: 0 Advertisement Sent: 0 Priority 0 Recv : 0 Priority 0 Sent : 0 Bad Type Errors : 0 Wrong Owner Errors: 0 IP TTL Error : 0 Pkt Length Errors : 0 Interval Errors : 0 Address Errors : 0 Auth Type Errors : 0 Auth Mismatchs : 0 Auth Failures : 0 Auth Header Errors: 0 --- VRRP Virtual Router vrrp1/2 (Backup) --- Master Transitions: 0 Advertisement Recv: 0 Advertisement Sent: 0 Priority 0 Recv : 0 Priority 0 Sent : 0 Bad Type Errors : 0 Wrong Owner Errors: 0 IP TTL Error : 0 Pkt Length Errors : 0 Interval Errors : 0 Address Errors : 0 Auth Type Errors : 0 Auth Mismatchs : 0 Auth Failures : 0 Auth Header Errors: 0 --- VRRP Virtual Router vrrp1/3 (Backup) --- Master Transitions: 0 Advertisement Recv: 0 Advertisement Sent: 0 Priority 0 Recv : 0 Priority 0 Sent : 0 Bad Type Errors : 0 Wrong Owner Errors: 0 IP TTL Error : 0 Pkt Length Errors : 0 Interval Errors : 0 Address Errors : 0 Auth Type Errors : 0 Auth Mismatchs : 0 Auth Failures : 0 Auth Header Errors: 0
1.52 show xc
show xc
1.52.1 Purpose
Displays a list of all cross-connects (XCs) currently configured on the system.
1.52.2 Command Mode
all modes
1.52.3 Syntax Description
This command has no keywords or arguments.
1.52.4 Default
None
1.52.5 Usage Guidelines
Use the show xc command to display a list of all XCs currently configured on the system.
- Note:
- The show xc command output displays information for both bypass and L2VPN XCs.
1.52.6 Examples
The following example displays output from the show xc command:
[local]Redback>show xc LDP L2VPN Circuits L2 Circuit L2 State Peer address VC Id L-Label State lg id 25 vlan-id 58 Down 3.3.3.3 102 131072 Down lg id 25 vlan-id 54:1 Down 3.3.3.3 103 131073 Down lg id 25 vlan-id 3501 Down 3.3.3.3 3501 131074 Down lg id 25 vlan-id 3502 Down 3.3.3.3 3502 131075 Down lg id 25 vlan-id 3503 Down 3.3.3.3 3503 131076 Down lg id 25 vlan-id 3504 Down 3.3.3.3 3504 131077 Down lg id 25 vlan-id 3505 Down 3.3.3.3 3505 131078 Down lg id 25 vlan-id 3506 Down 3.3.3.3 3506 131079 Down lg id 25 vlan-id 3507 Down 3.3.3.3 3507 131080 Down lg id 25 vlan-id 3508 Down 3.3.3.3 3508 131081 Down lg id 25 vlan-id 3509 Down 3.3.3.3 3509 131082 Down lg id 25 vlan-id 3510 Down 3.3.3.3 3510 131083 Down lg id 25 vlan-id 3511 Down 3.3.3.3 3511 131084 Down lg id 25 vlan-id 3512 Down 3.3.3.3 3512 131085 Down lg id 25 vlan-id 3513 Down 3.3.3.3 3513 131086 Down lg id 25 vlan-id 3514 Down 3.3.3.3 3514 131087 Down lg id 25 vlan-id 3515 Down 3.3.3.3 3515 131088 Down lg id 25 vlan-id 3516 Down 3.3.3.3 3516 131089 Down lg id 25 vlan-id 3517 Down 3.3.3.3 3517 131090 Down lg id 25 vlan-id 3518 Down 3.3.3.3 3518 131091 Down lg id 25 vlan-id 3519 Down 3.3.3.3 3519 131092 Down lg id 25 vlan-id 3520 Down 3.3.3.3 3520 131093 Down lg id 25 vlan-id 3521 Down 3.3.3.3 3521 131094 Down lg id 25 vlan-id 3522 Down 3.3.3.3 3522 131095 Down lg id 25 vlan-id 3523 Down 3.3.3.3 3523 131096 Down lg id 25 vlan-id 3524 Down 3.3.3.3 3524 131097 Down lg id 25 vlan-id 3525 Down 3.3.3.3 3525 131098 Down lg id 25 vlan-id 3526 Down 3.3.3.3 3526 131099 Down lg id 25 vlan-id 3527 Down 3.3.3.3 3527 131100 Down lg id 25 vlan-id 3528 Down 3.3.3.3 3528 131101 Down lg id 25 vlan-id 3529 Down 3.3.3.3 3529 131102 Down lg id 25 vlan-id 3530 Down 3.3.3.3 3530 131103 Down lg id 25 vlan-id 3531 Down 3.3.3.3 3531 131104 Down lg id 25 vlan-id 3532 Down 3.3.3.3 3532 131105 Down lg id 25 vlan-id 3533 Down 3.3.3.3 3533 131106 Down lg id 25 vlan-id 3534 Down 3.3.3.3 3534 131107 Down lg id 25 vlan-id 3535 Down 3.3.3.3 3535 131108 Down lg id 25 vlan-id 3536 Down 3.3.3.3 3536 131109 Down lg id 25 vlan-id 3537 Down 3.3.3.3 3537 131110 Down lg id 25 vlan-id 3538 Down 3.3.3.3 3538 131111 Down lg id 25 vlan-id 3539 Down 3.3.3.3 3539 131112 Down lg id 25 vlan-id 3540 Down 3.3.3.3 3540 131113 Down lg id 25 vlan-id 3541 Down 3.3.3.3 3541 131114 Down lg id 25 vlan-id 3542 Down 3.3.3.3 3542 131115 Down ---(more)---
Table 1 describes the fields in the show xc command output.
Field |
Description |
---|---|
L2 Circuit |
Displays the circuit type and identifier for the physical (Layer 2) circuit hosting the local end of the XC, in the following format:
|
L2 State |
Current state of the circuit. Can be Up (circuit is active) or Down (circuit is inactive). |
Peer address |
IP address of the peer router. |
VC Id |
Virtual circuit (XC) identifier. |
L-Label |
Inner label associated with the local end of the XC. |
State |
Current state of the VC. Can be Up (circuit is active) or Down (circuit is inactive). |
1.53 show xc (circuit)
To display information about all XCs configured on a specific port:
show xc circuit [detail]
To display information about an XC configured on a specific DLCI:
show xc circuit dlci dlci [detail]
To display information about an XC configured on a specific Point-to-Point Protocol (PPP) over Ethernet (PPPoE) session:
show xc circuit pppoe pppoe-session] [detail]
To display information about an XC configured on a specific VLAN:
show xc circuit vlan-id vlan-id [ipv6oe | pppoepppoe-session ] [detail]
To display information about an XC configured on a specific VPI and VCI:
show xc circuit vpi-vci vpi vci [ipv6oe | pppoe pppoe-session] [detail]
1.53.1 Purpose
Displays information about an XC configured specific circuit.
1.53.2 Command Mode
all modes
1.53.3 Syntax Description
circuit |
Physical circuit identifier for the XC whose bypass information is to be displayed. The circuit format is defined as follows:
|
dlci dlci |
Data-link connection identifier (DLCI) for the Frame Relay PVC. |
pppoe pppoe-session |
PPPoE session identifier. |
vlan-id vlan-id |
Specifies a Virtual LAN (VLAN). |
ipv6oe |
Specifies an IP Version 6 over Ethernet (IPv6oE)-encapsulated circuit. |
vpi-vci vpi vci |
Virtual path identifier (VPI) and virtual circuit identifier (VCI) for an ATM PVC. The range of values for the VPI is 0 to 255. The range of values for the VCI is 1 to 65535. |
detail |
Displays detailed information about the specified XC. |
1.53.4 Default
None
1.53.5 Usage Guidelines
Use the show xc (circuit) command to display information about an XC configured on a specific circuit.
1.53.6 Examples
The following example displays output from the show xc command for the XCs whose local endpoint is configured on slot 5, port 9:
[local]Redback>show xc 5/9 Circuit State XC Circuit State 5/9 vlan-id 500:50 Up lg 26 vlan-id 500:50 Up lg 26 vlan-id 32 Up 5/9 vlan-id 32 Up lg 26 vlan-id 500:40 Up 5/9 vlan-id 500:40 Up lg 26 vlan-id 500:41 Up 5/9 vlan-id 500:41 Up lg 26 vlan-id 500:42 Up 5/9 vlan-id 500:42 Up lg 26 vlan-id 501:1 Up 5/9 vlan-id 501:1 Up lg 26 vlan-id 501:2 Up 5/9 vlan-id 501:2 Up lg 26 vlan-id 501:3 Up 5/9 vlan-id 501:3 Up lg 26 vlan-id 501:4 Up 5/9 vlan-id 501:4 Up lg 26 vlan-id 501:5 Up 5/9 vlan-id 501:5 Up lg 26 vlan-id 501:6 Up 5/9 vlan-id 501:6 Up lg 26 vlan-id 501:7 Up 5/9 vlan-id 501:7 Up lg 26 vlan-id 501:8 Up 5/9 vlan-id 501:8 Up lg 26 vlan-id 501:9 Up 5/9 vlan-id 501:9 Up lg 26 vlan-id 501:10 Up 5/9 vlan-id 501:10 Up lg 26 vlan-id 501:11 Up 5/9 vlan-id 501:11 Up lg 26 vlan-id 501:12 Up 5/9 vlan-id 501:12 Up lg 26 vlan-id 501:13 Up 5/9 vlan-id 501:13 Up lg 26 vlan-id 501:14 Up 5/9 vlan-id 501:14 Up lg 26 vlan-id 501:15 Up 5/9 vlan-id 501:15 Up lg 26 vlan-id 501:16 Up 5/9 vlan-id 501:16 Up lg 26 vlan-id 501:17 Up 5/9 vlan-id 501:17 Up ---(more)---
Table 14 describes the fields in the show xc (circuit) command output.
Field |
Description |
---|---|
Circuit |
Displays the circuit type and identifier for the physical (Layer 2) circuit hosting the local end of the XC, in the following format:
|
State |
Current state of the circuit. Can be Up (circuit is active) or Down (circuit is inactive). |
XC Circuit |
Displays the circuit type and identifier for the XC circuit, in the following format:
|
State |
Current state of the XC. Can be Up (circuit is active) or Down (circuit is inactive). |
The following example shows sample output from the show xc command for a specific XC. In this example, detailed information is displayed for the XC configured on port 9 on the card in slot 5, on the VLAN 501:17:
[local]Redback>show xc 5/9 vlan-id 501:17 detail Displaying circuit: 5/9 vlan-id 501:17, State: Up ----------------------------------------------------------- Circuit handle : 5/9:1023:63/1/2/7591 Encapsulation : ether-dot1q-tunnel FSM State : Crossconnected Group's grid : 0x0 Adj id : 0xff480015 NH Grid : 0x3fb0002a rcm range cfg rcvd: Yes rcm expl cfg rcvd : No ism cfg rcvd : Yes pending ism cfg : No hole punched : No rcm cfg deleted : No inbound : No crossconnected : Yes interworking : No group name set : No prot acct : No prot ccct : No prot active : No prot economical : No slot mask cfg : 0x10 slot mask run : 0x10 slot mask set : 0x0 slot mask clear : 0x0 ppas registered : Yes Displaying Peer circuit: lg 26 vlan-id 501:17, State: Up ----------------------------------------------------------- Circuit handle : 255/22:1:27/1/2/2549 Encapsulation : ether-dot1q-tunnel FSM State : Crossconnected ---(more)---
Table 15 describes the fields in the show xc detail (circuit) command.
Field |
Description |
---|---|
Displaying circuit |
Circuit type and identifier for the physical (Layer 2) circuit hosting the local end of the XC, in the following format:
|
State |
Current state of the circuit. Can be Up (circuit is active) or Down (circuit is inactive). |
Circuit handle |
Handle internally assigned to the L2VPN circuit. |
Encapsulation |
Type of encapsulation on the local end of the XC. Can be:
|
FSM State |
Current state of the internal finite state machine (FSM). |
Group's grid |
Group that the XC is configured under. This ID corresponds to the XC group name. |
Adj id |
Adjacency ID for this endpoint. |
rcm range cfg rcvd |
Indicates whether ranged cross connect configuration has been received for this endpoint. |
ism cfg rcvd |
Indicates whether this endpoint is bound to a bypass circuit (using the bind bypass command). |
hole punched |
Indicates a hole is punched in the range for this XC, and the non-ranged XC is the active XC for this endpoint. This occurs when ranged and non-ranged configuration is received for an XC. |
inbound |
Indicates whether this circuit was the first circuit listed when the XC was configured with the xc command. |
prot acct |
Indicates whether this circuit is the aggregate circuit for a link-group. |
prot active |
Indicates whether the link-group for this circuit is active (configured on one or more ports). |
slot mask cfg |
Configured slot mask, in hexadecimal format. |
slot mask set |
Slot mask that XCD needs to process for this endpoint. The slot mask is displayed in hexadecimal format. |
ppas registered |
Indicates whether the PPA for this endpoint is registered with XCD. |
NH Grid |
Next-hop grid from this endpoint, in hexadecimal format. |
rcm expl cfg rcvd |
Indicates whether non-ranged XC configuration was received for this endpoint. |
pending ism cfg |
Indicates whether a configure message for this endpoint is waiting to be sent to ISM. This field is specific to interworking XCs. |
rcm cfg deleted |
Indicates whether non-ranged XC configuration for an endpoint is deleted. This field is always set to No. |
crossconnected |
Indicates whether this XC is installed on the PPA. |
group name set |
Indicates whether the group name is set. This fields is always set to No. |
prot ccct |
Indicates whether this circuit is a constituent circuit in a link group. |
prot economical |
Indicates whether this circuit is economical. |
slot mask run |
Configured slot mask, in hexadecimal format. |
slot mask clear |
Slot mask bits that need to be cleared, in hexadecimal format. |
Displaying Peer circuit |
Displays information for Layer 2 (physical) circuit hosting the remote end of the XC, in the following format:
|
State |
Current state of the circuit. Can be Up (circuit is active) or Down (circuit is inactive). |
Circuit handle |
Handle internally assigned to the L2VPN circuit. |
FSM State |
Current state of the internal finite state machine (FSM) for this endpoint. |
1.54 show xc bypass
To display a list of all bypass cross-connects (XCs) configured on the system:
show xc bypass
To display information about the XCs configured on under a specific link group:
show xc bypass lg {name | num} [vlan-id vlan-id [ipv6oe |pppoe pppoe-session] | vpi-vci vpi vci [ipv6oe |pppoe pppoe-session] | pppoe pppoe-session] [detail]
To display information about the bypass XCs configured on a specific circuit:
show xc circuit [vlan-id vlan-id [ipv6oe | pppoe pppoe-session] | vpi-vci vpi vci [ipv6oe | pppoe pppoe-session] | pppoe pppoe-session] [detail]
To display information about the active (up) bypass XCs configured on the system:
show xc bypass up [lg {name | num} | circuit] [vlan-id vlan-id [ipv6oe | pppoe pppoe-session] | vpi-vci vpi vci [ipv6oe | pppoe pppoe-session] | pppoe pppoe-session] [detail]
To display information about the inactive (down) bypass XCs configured on the system:
show xc bypass down [lg {name | num} | circuit] [vlan-id vlan-id [ipv6oe | pppoe pppoe-session] | vpi-vci vpi vci [ipv6oe pppoe pppoe-session] | pppoe pppoe-session]| [detail]
To display brief (summarized) information about all bypass XCs configured on the system:
show xc bypass summary
1.54.1 Purpose
Displays information about the bypass XCs configured on this system.
1.54.2 Command Mode
all modes
1.54.3 Syntax Description
lg |
Displays bypass information for a specific link group XC. |
name |
Specifies the name of an access link group XC whose bypass information to display. |
num |
Specifies the ID of an access link group XC whose bypass information to display. The link-group ID is automatically assigned by the SmartEdge router, and is displayed when you enter the show link-group detail command. |
circuit |
Physical circuit identifier for the XC whose bypass information is to be displayed. The circuit format is defined as follows:
|
vlan-id vlan-id |
Specifies an 802.1Q Virtual LAN (VLAN) whose bypass information to display. |
vpi-vci vpi vci |
Specifies a virtual path identifier (VPI) and virtual circuit identifier (VCI) for the bypass (ATM) XC whose information you want to display. The range of values is 0 to 255 and 1 to 65535. |
ipv6oe |
Displays bypass XC information for an IP Version 6 over Ethernet (IPv6oE)-encapsulated circuit. |
pppoe session-id |
Specifies the PPPoE encapsulation session whose bypass XC information to display. |
up |
Displays bypass information about the active (up) XCs on the system. |
down |
Displays bypass information about the inactive (down) XCs on the system. |
detail |
Displays more detailed output about the specified bypass XC. |
summary |
Displays summarized information about the specified bypass XC. |
1.54.4 Default
None
1.54.5 Usage Guidelines
Use the show xc bypass command to display bypass information about the XCs configured on this system.
1.54.6 Examples
The following example displays output from the show xc bypass command:
[local]Redback>show xc bypass Circuit State XC Circuit State 5/9 vlan-id 500:50 Up lg 26 vlan-id 500:50 Up lg 26 vlan-id 32 Up 5/9 vlan-id 32 Up lg 26 vlan-id 500:40 Up 5/9 vlan-id 500:40 Up lg 26 vlan-id 500:41 Up 5/9 vlan-id 500:41 Up lg 26 vlan-id 500:42 Up 5/9 vlan-id 500:42 Up lg 26 vlan-id 501:1 Up 5/9 vlan-id 501:1 Up lg 26 vlan-id 501:2 Up 5/9 vlan-id 501:2 Up lg 26 vlan-id 501:3 Up 5/9 vlan-id 501:3 Up lg 26 vlan-id 501:4 Up 5/9 vlan-id 501:4 Up lg 26 vlan-id 501:5 Up 5/9 vlan-id 501:5 Up lg 26 vlan-id 501:6 Up 5/9 vlan-id 501:6 Up lg 26 vlan-id 501:7 Up 5/9 vlan-id 501:7 Up lg 26 vlan-id 501:8 Up 5/9 vlan-id 501:8 Up lg 26 vlan-id 501:9 Up 5/9 vlan-id 501:9 Up lg 26 vlan-id 501:10 Up 5/9 vlan-id 501:10 Up lg 26 vlan-id 501:11 Up 5/9 vlan-id 501:11 Up lg 26 vlan-id 501:12 Up 5/9 vlan-id 501:12 Up lg 26 vlan-id 501:13 Up 5/9 vlan-id 501:13 Up lg 26 vlan-id 501:14 Up 5/9 vlan-id 501:14 Up lg 26 vlan-id 501:15 Up 5/9 vlan-id 501:15 Up lg 26 vlan-id 501:16 Up 5/9 vlan-id 501:16 Up lg 26 vlan-id 501:17 Up 5/9 vlan-id 501:17 Up ---(more)---
Table 2 describes the fields in the show xc bypass command output.
Field |
Description |
---|---|
Circuit |
Displays the circuit type and identifier for the physical (Layer 2) circuit hosting the local end of the XC, in the following format:
|
State |
Current state of the circuit. Can be Up (circuit is active) or Down (circuit is inactive). |
XC Circuit |
Displays the circuit type and identifier for the XC circuit, in the following format:
|
State |
Current state of the XC. Can be Up (circuit is active) or Down (circuit is inactive). |
The following example displays output from the show xc bypass command. In this example, the command output displays information about the bypass XC on port 9 on the card in slot 5 on VLAN 501:16:
[local]Redback>show xc bypass 5/9 vlan-id 501:16 Circuit State XC Circuit State lg 26 vlan-id 501:16 Up 5/9 vlan-id 501:16 Up
The show xc bypass command output is described in Table 2.
The following example displays summarized output from the show xc bypass command:
[local]Redback>show xc bypass summary Endpoints total: 9019, Up: 9019, Down: 0 Crossconnects total: 4505, Up: 4505, Down: 0
Table 3 describes the fields in the show xc bypass summary command output.
Field |
Description |
---|---|
Endpoints total: |
Total number of active and inactive XC endpoints on this system that are bound to bypass LSPs. |
Crossconnects total: |
Total number of active and inactive XCs configured on this system. This field is typically one-half of the Endpoints total. |
1.55 show xc detail
show xc detail
1.55.1 Purpose
Displays detailed information about all cross-connects (XCs) configured on the system.
1.55.2 Command Mode
all modes
1.55.3 Syntax Description
This command has no keywords or arguments.
1.55.4 Default
None
1.55.5 Usage Guidelines
Use the show xc detail command to display detailed information about all XCs configured on this system.
- Note:
- The show xc detail command output displays information for both bypass and L2VPN XCs.
1.55.6 Examples
The following example displays output from the show xc detail command:
[local]Redback>show xc detail LDP L2VPN Circuit lg id 25 vlan-id 58 L2 State : Up Peer : 3.3.3.3 VC ID : 102 XC state : Up Local Label : 131072 Access Circuit : 255/22:1:26/1/2/6 Remote Label : 131126 L2VPN Circuit : 255/12:103:63/0/1/1 EXP bits : 0 Local Encap : dot1q tsp Remote Group ID : 0 Remote Encap : Local VC Type : VLAN Remote VC Type : VLAN Local VC MTU : 1500 Remote VC MTU : 1500 Local VC Status : forwarding Remote VC Status : forwarding XC group : default Negotiated cbit : no LSP Configured : LSP Used : XC profile : Flags 0x800819e9: in-rib, in-lblmap, in-ldp, from-ldp, from-cfg : peer-up LDP L2VPN Circuit lg id 25 vlan-id 54:1 L2 State : Up Peer : 3.3.3.3 VC ID : 103 XC state : Up Local Label : 131073 Access Circuit : 255/22:1:26/1/2/15 Remote Label : 131127 L2VPN Circuit : 255/12:104:63/0/1/2 EXP bits : 0 Local Encap : dot1q-1q tu-tsp Remote Group ID : 0 Remote Encap : Local VC Type : VLAN Remote VC Type : VLAN Local VC MTU : 1500 Remote VC MTU : 1500 Local VC Status : forwarding Remote VC Status : forwarding XC group : default Negotiated cbit : no ---(more)---
Table 18 describes the fields in the show xc detail command.
Field |
Description |
---|---|
L2 State |
Current state of the layer 2 (physical) circuit. Can be Up (active), Standby, or Down (inactive). |
VC ID |
Identifies the virtual circuit on which this XC is configured. |
Local Label |
Inner label associated with the local end of a cross-connection. |
Remote Label |
Inner label associated with the remote end of a cross-connection. |
EXP bits |
EXP bits to be used for transport. Range is from 0 through 7. |
Remote Group ID |
Identifies the link group hosting this XC at the remote end (if the XC is configured under a link group). |
Local VC Type |
Type of circuit hosting the local end of the XC. |
Local VC MTU |
MTU on the local end of the XC. |
Local VC Status |
Current forwarding status of the VC hosting the local end of the XC. The status can be Forwarding, Forwarding Standby, Receive, or Transmit. |
XC group |
Identifies the group under which the local end of the XC is configured. |
LSP Configured |
Name of the LSP mapped to the XC (if the XC is configured on an LSP). |
XC profile |
Identifies any XC profile that is attached to this XC. The XC profile determines the configuration used by the XC. |
Peer |
IP address of the peer hosting the remote end of the XC. |
XC state |
Current state of the XC. Can be Up (active), Standby, or Down (inactive). |
Access Circuit |
Circuit handle internally assigned to the local access circuit on the XC. |
L2VPN Circuit |
Circuit handle internally assigned to the L2VPN circuit. |
Local Encap |
Type of encapsulation on the local end of the XC. Can be:
|
Remote Encap |
Type of encapsulation on the remote end of the XC. Can be:
|
Remote VC Type |
Type of virtual circuit hosting the remote end of the XC. Can be VLAN, VPI-VCI, or PPPoE. |
Remote VC MTU |
MTU on the circuit hosting the remote end of the XC. |
Remote VC Status |
Current forwarding status of the VC hosting the remote end of the XC. The status can be Forwarding, Forwarding Standby, Receive, or Transmit. |
Negotiated cbit |
Indicates whether the control word is present in the pseudowire PDU. The presence of a sequence number indicates that the control word is present in the pseudowire PDU. If the negotiated value is set to yes, then only the control word is present in the PDU that is carried over the pseudowire. |
LSP Used |
Displays whether the primary or bypass (backup) LSP is currently active. |
Flags 0x800819e9: |
Identifies the current running state of the XC. |
1.56 show xc down
show xc down [detail]
1.56.1 Purpose
Displays information about the inactive (down) bypass cross-connects (XCs) configured on this system.
1.56.2 Command Mode
all modes
1.56.3 Syntax Description
detail |
Displays more detailed output about the inactive bypass XCs configured on this system. |
1.56.4 Default
None
1.56.5 Usage Guidelines
Use the show xc down command to display information about the inactive (down) bypass XCs configured on this system.
- Note:
- The show xc down command displays information for bypass XCs only; the show xc down command output does not display information for L2VPN XCs.
1.56.6 Examples
The following example displays output from the show xc down command:
[local]Redback>show xc down LDP L2VPN Circuits L2 Circuit L2 State Peer address VC Id L-Label State lg id 25 vlan-id 3501 Up 3.3.3.3 3501 131074 Down lg id 25 vlan-id 3502 Up 3.3.3.3 3502 131075 Down lg id 25 vlan-id 3503 Up 3.3.3.3 3503 131076 Down lg id 25 vlan-id 3504 Up 3.3.3.3 3504 131077 Down lg id 25 vlan-id 3505 Up 3.3.3.3 3505 131078 Down lg id 25 vlan-id 3506 Up 3.3.3.3 3506 131079 Down lg id 25 vlan-id 3507 Up 3.3.3.3 3507 131080 Down lg id 25 vlan-id 3508 Up 3.3.3.3 3508 131081 Down lg id 25 vlan-id 3509 Up 3.3.3.3 3509 131082 Down lg id 25 vlan-id 3510 Up 3.3.3.3 3510 131083 Down lg id 25 vlan-id 3511 Up 3.3.3.3 3511 131084 Down lg id 25 vlan-id 3512 Up 3.3.3.3 3512 131085 Down lg id 25 vlan-id 3513 Up 3.3.3.3 3513 131086 Down lg id 25 vlan-id 3514 Up 3.3.3.3 3514 131087 Down lg id 25 vlan-id 3515 Up 3.3.3.3 3515 131088 Down lg id 25 vlan-id 3516 Up 3.3.3.3 3516 131089 Down lg id 25 vlan-id 3517 Up 3.3.3.3 3517 131090 Down lg id 25 vlan-id 3518 Up 3.3.3.3 3518 131091 Down lg id 25 vlan-id 3768 Up 3.3.3.3 3768 131341 Down lg id 25 vlan-id 3769 Up 3.3.3.3 3769 131342 Down ---(more)---
The following table describes the fields in the show xc down command output.
Field |
Description |
---|---|
L2 Circuit |
Displays the circuit type and identifier for the physical (Layer 2) circuit hosting the local end of the XC, in the following format:
|
L2 State |
Current state of the Layer 2 (physical) circuit. Can be Up (circuit is active) or Down (circuit is inactive). |
Peer address |
IP address of the peer router. |
VC Id |
Virtual circuit identifier for the local end of the XC. |
L-Label |
Local label. Inner label associated with the local end of an L2VPN cross-connection. |
State |
Current state of the VC. Can be Up (circuit is active) or Down (circuit is inactive). |
1.57 show xc group
show xc group {group-name | default} {detail}
1.57.1 Purpose
Displays information about a cross-connect (XC) group.
1.57.2 Command Mode
all modes
1.57.3 Syntax Description
group |
Displays information about the XCs in a specific XC group. |
group-name |
Name of the XC group whose information to display. Displays information about the XCs in the specified XC group only. |
default |
Displays information about the XCs in the default XC group only. |
detail |
Optional. Displays detailed information about the L2VPN cross-connections in the specified group. |
1.57.4 Default
None
1.57.5 Usage Guidelines
Use the show xc group command to display information about an XC group.
1.57.6 Examples
The following example displays output from the show xc group command. In this example, output is displayed for the default XC group:
[local]Redback>show xc group default LDP L2VPN Circuits L2 Circuit L2 State Peer address VC Id L-Label State lg id 25 vlan-id 58 Up 3.3.3.3 102 131072 Up lg id 25 vlan-id 54:1 Up 3.3.3.3 103 131073 Up lg id 25 vlan-id 3501 Up 3.3.3.3 3501 131074 Up lg id 25 vlan-id 3502 Up 3.3.3.3 3502 131075 Up lg id 25 vlan-id 3503 Up 3.3.3.3 3503 131076 Up lg id 25 vlan-id 3504 Up 3.3.3.3 3504 131077 Up lg id 25 vlan-id 3505 Up 3.3.3.3 3505 131078 Up lg id 25 vlan-id 3506 Up 3.3.3.3 3506 131079 Up lg id 25 vlan-id 3507 Up 3.3.3.3 3507 131080 Up lg id 25 vlan-id 3508 Up 3.3.3.3 3508 131081 Up lg id 25 vlan-id 3509 Up 3.3.3.3 3509 131082 Up lg id 25 vlan-id 3510 Up 3.3.3.3 3510 131083 Up lg id 25 vlan-id 3511 Up 3.3.3.3 3511 131084 Up lg id 25 vlan-id 3512 Up 3.3.3.3 3512 131085 Up lg id 25 vlan-id 3513 Up 3.3.3.3 3513 131086 Up lg id 25 vlan-id 3514 Up 3.3.3.3 3514 131087 Up lg id 25 vlan-id 3515 Up 3.3.3.3 3515 131088 Up lg id 25 vlan-id 3516 Up 3.3.3.3 3516 131089 Up lg id 25 vlan-id 3517 Up 3.3.3.3 3517 131090 Up lg id 25 vlan-id 3518 Up 3.3.3.3 3518 131091 Up ---(more)---
The following table describes the fields in the show xc group command output.
Field |
Description |
---|---|
L2 Circuit |
Displays the circuit type and identifier for the physical (Layer 2) circuit hosting the local end of the XC, in the following format:
|
L2 State |
Current state of the Layer 2 (physical) circuit. Can be Up (circuit is active) or Down (circuit is inactive). |
Peer address |
IP address of the peer router. |
VC Id |
Virtual circuit identifier for the local end of the XC. |
L-Label |
Inner label associated with the local end of the XC. |
State |
Current state of the VC. Can be Up (circuit is active) or Down (circuit is inactive). |
The following example displays detailed output from the show xc group command. In this example, detailed output is displayed for the default XC group:
[local]Redback>show xc group default detail LDP L2VPN Circuit lg id 25 vlan-id 58 L2 State : Up Peer : 3.3.3.3 VC ID : 102 XC state : Up Local Label : 131072 Access Circuit : 255/22:1:26/1/2/6 Remote Label : 131126 L2VPN Circuit : 255/12:103:63/0/1/1 EXP bits : 0 Local Encap : dot1q tsp Remote Group ID : 0 Remote Encap : Local VC Type : VLAN Remote VC Type : VLAN Local VC MTU : 1500 Remote VC MTU : 1500 Local VC Status : forwarding Remote VC Status : forwarding XC group : default Negotiated cbit : no LSP Configured : LSP Used : XC profile : Flags 0x800819e9: in-rib, in-lblmap, in-ldp, from-ldp, from-cfg : peer-up LDP L2VPN Circuit lg id 25 vlan-id 54:1 L2 State : Up Peer : 3.3.3.3 VC ID : 103 XC state : Up Local Label : 131073 Access Circuit : 255/22:1:26/1/2/15 Remote Label : 131127 L2VPN Circuit : 255/12:104:63/0/1/2 EXP bits : 0 Local Encap : dot1q-1q tu-tsp Remote Group ID : 0 Remote Encap : Local VC Type : VLAN Remote VC Type : VLAN Local VC MTU : 1500 Remote VC MTU : 1500 Local VC Status : forwarding Remote VC Status : forwarding XC group : default Negotiated cbit : no LSP Configured : LSP Used : XC profile : Flags 0x800819e9: in-rib, in-lblmap, in-ldp, from-ldp, from-cfg : peer-up ---(more)---
Table 21 describes the fields in the show xc group detail command.
Field |
Description |
---|---|
L2 State |
Current state of the layer 2 (physical) circuit. Can be Up (active), Standby, or Down (inactive). |
VC ID |
Identifies the virtual circuit on which this XC is configured. |
Local Label |
Inner label associated with the local end of a cross-connection. |
Remote Label |
Inner label associated with the remote end of a cross-connection. |
EXP bits |
EXP bits to be used for transport. Range is from 0 through 7. |
Remote Group ID |
Identifies the link group hosting this XC at the remote end (if the XC is configured under a link group). |
Local VC Type |
Type of circuit hosting the local end of the XC. |
Local VC MTU |
MTU on the local end of the XC. |
Local VC Status |
Current forwarding status of the VC hosting the local end of the XC. The status can be Forwarding, Forwarding Standby, Receive, or Transmit. |
XC group |
Identifies the group under which the local end of the XC is configured. |
LSP Configured |
Name of the LSP mapped to the XC (if the XC is configured on an LSP). |
XC profile |
Identifies any XC profile that is attached to this XC. The XC profile determines the configuration used by the XC. |
Peer |
IP address of the peer hosting the remote end of the XC. |
XC state |
Indicate whether the XC is active (Up) or inactive (Down). |
Access Circuit |
Circuit handle internally assigned to the local access circuit on the XC. |
L2VPN Circuit |
Circuit handle internally assigned to the L2VPN circuit. |
Local Encap |
Type of encapsulation on the local end of the XC. Can be:
|
Remote Encap |
Type of encapsulation on the remote end of the XC. Can be:
|
Remote VC Type |
Type of virtual circuit hosting the remote end of the XC. Can be VLAN, VPI-VCI, or PPPoE. |
Remote VC MTU |
MTU on the circuit hosting the remote end of the XC. |
Remote VC Status |
Current forwarding status of the VC hosting the remote end of the XC. The status can be Forwarding, Forwarding Standby, Receive, or Transmit. |
Negotiated cbit |
Indicates whether the control word is present in the pseudowire PDU. The presence of a sequence number indicates that the control word is present in the pseudowire PDU. If the negotiated value is set to yes, then only the control word is present in the PDU that is carried over the pseudowire. |
LSP Used |
Displays whether the primary or bypass (backup) LSP is currently active. |
Flags |
Identify the current running state of the XC. |
1.58 show xc l2vpn
show xc l2vpn [[slot/port] circuit-id | group {group-name | default} | lg id lg-name-in | ldp} | peer peer-addr| route | static] [detail] | [summary]]
1.58.1 Purpose
Displays Layer 2 Virtual Private Network (L2VPN) cross-connect information.
1.58.2 Command Mode
all modes
1.58.3 Syntax Description
circuit-id |
Optional. Layer 2 (L2) circuit ID. Depending on the type of circuit being cross-connected, the L2 circuit ID takes one of the following constructs:
|
For Ethernet ports with no 802.1Q PVCs, no circuit descriptor is specified. | |
group |
Optional. Displays cross-connection information only for a specific cross-connection group. |
group-name |
Cross-connection group name. |
default |
Displays cross-connection information only for the default cross-connection group. |
lg id lg-name-in |
Specifies the name of an access link group to be cross-connected inbound |
ldp |
Optional. Displays only Label Distribution Protocol (LDP) L2VPN cross-connection information. |
peer peer-addr |
IP address of the remote peer provider edge (PE) router. |
static |
Optional. Displays only static L2VPN cross-connection information. |
route |
Displays L2VPN route information. |
detail |
Optional. Displays detailed L2VPN cross-connection information. When used with the xc-circuit argument, displays detailed L2VPN cross-connection information only for the specified cross-connected circuit. |
summary |
Displays summary L2VPN information. |
1.58.4 Default
None.
1.58.5 Usage Guidelines
Use the show xc l2vpn command to display L2VPN-related information.
- Note:
- By default, most show commands (in any mode) display information for the current context only or, depending on the command syntax, for all contexts. If you are an administrator for the local context, you can insert the optional context ctx-name construct, preceding the show command, to view output for the specified context without entering that context. For more information about using the context ctx-name construct, see the context command description.
- Note:
- By appending a space followed by the pipe ( | ) character at the end of a show command, you can filter the output using a set of modifier keywords and arguments. For more information, see Modifying Output of show Commands in Using the CLI.
1.58.6 Examples
The following example displays information about all L2VPN cross-connections that are configured on the current router:
[local]Redback# show xc l2vpn Static L2VPN Circuits L2 Circuit L2 State Peer address Label 10/1 vlan-id 1 Up 1.1.1.2 4097 10/1 vlan-id 2 Up 1.1.1.2 4098 10/1 vlan-id 3 Up 1.1.1.2 4099 10/1 vlan-id 4 Up 1.1.1.2 4100 10/1 vlan-id 5 Up 1.1.1.2 4101 LDP L2VPN Circuits L2 Circuit L2 State Peer address VC Id L-Label State VPLS 0x4000002 Up 83.1.1.1 10 131073 Down VPLS 0x4000003 Up 111.111.111.111 10 131074 Down 4/1 vpi-vci 1 100 Up 111.111.111.111 10000 131075 Down
The following table describes the fields in the show xc l2vpn command output.
Field |
Description |
---|---|
L2 Circuit |
Displays the circuit type and identifier for the physical (Layer 2) circuit hosting the local end of the XC, in the following format:
|
L2 State |
Current state of the Layer 2 (physical) circuit. Can be Up (circuit is active) or Down (circuit is inactive). |
Peer address |
IP address of the peer router. |
L-Label |
Inner label associated with the local end of the L2VPN XC. |
The following example shows how to display L2VPN route information:
[local]Redback>show xc l2vpn route L2 Circuit XC Circuit Next-hop Uptime 10/1:1023:63/1/2/4099 255/12:2:63/0/1/10 1.1.1.2 01:41:59 10/1:1023:63/1/2/4100 255/12:3:63/0/1/11 1.1.1.2 01:41:59 10/1:1023:63/1/2/4101 255/12:4:63/0/1/12 1.1.1.2 01:41:58 10/1:1023:63/1/2/4102 255/12:5:63/0/1/13 1.1.1.2 01:41:58 10/1:1023:63/1/2/4103 255/12:6:63/0/1/14 1.1.1.2 01:41:37
The following table describes the fields in the show xc l2vpn route command output.
Field |
Description |
---|---|
L2 Circuit |
Displays the circuit type and identifier for the physical (Layer 2) circuit hosting the local end of the XC, in the following format:
|
XC Circuit |
Circuit handle internally assigned to the XC (L2VPN) circuit. |
Next-hop |
IP address of the next-hop peer. |
Uptime |
Amount of time the XC (L2VPN) circuit has been in the Up state, displayed in the hours:minutes:seconds format. |
The following example displays static L2VPN cross-connection information:
[local]RedBack#show xc l2vpn static Static L2VPN Circuits L2 Circuit L2 State Peer address Label 10/1 vlan-id 1 Up 1.1.1.2 4097 10/1 vlan-id 2 Up 1.1.1.2 4098 10/1 vlan-id 3 Up 1.1.1.2 4099 10/1 vlan-id 4 Up 1.1.1.2 4100 10/1 vlan-id 5 Up 1.1.1.2 4101
The following example displays detailed information about the L2VPN cross-connection configured on port 4 of the card installed in slot 1:
[local]Redback>show xc l2vpn 4/1 vpi-vci 1 100 detail LDP L2VPN Circuit 4/1 vpi-vci 1 100 L2 State : Up Peer : 111.111.111.111 VC ID : 10000 XC state : Down Local Label : 131075 Access Circuit : 4/1:1:63/1/2/4098 Remote Label : 131072 L2VPN Circuit : 255/12:785:63/0/1/8 EXP bits : 0 Local Encap : atm-cell Remote Group ID : 0 Remote Encap : Local VC Type : ATM VCC Cell Remote VC Type : ATM VCC Cell Local VC MTU : 4470 Remote VC MTU : 0 XC group : foo Negotiated cbit : no Flags 0x0008014a: delete-sig, in-lblmap, in-ldp, from-cfg :
The following table describes the fields in the show xc l2vpn detail command.
Field |
Description |
---|---|
L2 State |
Current state of the layer 2 (physical) circuit. Can be Up (active), Standby, or Down (inactive). |
VC ID |
Identifies the virtual circuit on which this XC is configured. |
Local Label |
Inner label associated with the local end of an L2VPN cross-connection. |
Remote Label |
Inner label associated with the remote end of an L2VPN cross-connection. |
EXP bits |
EXP bits to be used for transport. Range is from 0 through 7. |
Remote Group ID |
Identifies the link group hosting this XC at the remote end (if the XC is configured under a link group). |
Local VC Type |
Type of circuit hosting the local end of the XC. |
Local VC MTU |
MTU on the local end of the XC. |
XC group |
Identifies the group under which the local end of the XC is configured. |
Peer |
IP address of the peer hosting the remote end of the XC. |
XC state |
Indicate whether the XC is active (Up) or inactive (Down). |
Access Circuit |
Circuit handle internally assigned to the local access circuit on the XC. |
L2VPN Circuit |
Circuit handle internally assigned to the L2VPN circuit. |
Local Encap |
Type of encapsulation on the local end of the XC. Can be:
|
Remote Encap |
Type of encapsulation on the remote end of the XC. Can be:
|
Remote VC Type |
Type of virtual circuit hosting the remote end of the XC. Can be VLAN, VPI-VCI, or PPPoE. |
Remote VC MTU |
MTU on the circuit hosting the remote end of the XC. |
Negotiated cbit |
Indicates whether the control word is present in the pseudowire PDU. The presence of a sequence number indicates that the control word is present in the pseudowire PDU. If the negotiated value is set to yes, then only the control word is present in the PDU that is carried over the pseudowire. |
Flags |
For internal use: Identify the current running state of the XC. |
1.59 show xc summary
show xc summary
1.59.1 Purpose
Displays summarized information about all XCs configured on the system.
1.59.2 Command Mode
all modes
1.59.3 Syntax Description
This command has no keywords or arguments.
1.59.4 Default
None
1.59.5 Usage Guidelines
Use the show xc summary command to display summarized information about all XCs configured on the system.
1.59.6 Examples
The following example displays output from the show xc summary command:
[local]Redback>show xc summary Total Static XCs: 0, Active Static XCs: 0 Total LDP XCs: 2660, Active LDP XCs: 2660 Total Bypass Endpoints: 9019, Active Bypass Endpoints: 9019 Total Bypass XCs: 4505, Active Bypass XCs: 4505
The following table describes the fields in the show xc summary command output.
Field |
Description |
---|---|
Total Static XCs |
Total number of static XCs currently configured on this router. |
Active Static XCs |
Number of static XCs that are currently active on this router. |
Total LDP XCs |
Total number of LDP XCs currently configured on this router. |
Active LDP XCs |
Number of LDP XCs that are currently active on this router. |
Total Bypass Endpoints |
Total number of bypass circuits currently configured on this router. |
Active Bypass Endpoints |
Number of bypass circuits that are currently active on this router. |
Total Bypass XCs |
Total number of bypass XCs currently configured on this router. |
Active Bypass XCs |
Number of bypass XCs that are currently active on this router. |
1.60 show xc up
show xc up [detail]
1.60.1 Purpose
Displays information about the active (up) bypass XCs configured on this system.
1.60.2 Command Mode
all modes
1.60.3 Syntax Description
detail |
Displays detailed information about the specified active bypass XC. |
1.60.4 Default
None
1.60.5 Usage Guidelines
Use the show xc up command to display information about the active (up) bypass XCs configured on this system.
- Note:
- The show xc up command displays information for bypass XCs only; the show xc up command output does not display information for L2VPN XCs.
1.60.6 Examples
The following example displays output from the show xc up command:
[local]Redback>show xc up LDP L2VPN Circuits L2 Circuit L2 State Peer address VC Id L-Label State lg id 25 vlan-id 58 Up 3.3.3.3 102 131072 Up lg id 25 vlan-id 54:1 Up 3.3.3.3 103 131073 Up lg id 25 vlan-id 3501 Up 3.3.3.3 3501 131074 Up lg id 25 vlan-id 3502 Up 3.3.3.3 3502 131075 Up lg id 25 vlan-id 3503 Up 3.3.3.3 3503 131076 Up lg id 25 vlan-id 3504 Up 3.3.3.3 3504 131077 Up lg id 25 vlan-id 3505 Up 3.3.3.3 3505 131078 Up lg id 25 vlan-id 3506 Up 3.3.3.3 3506 131079 Up lg id 25 vlan-id 3507 Up 3.3.3.3 3507 131080 Up lg id 25 vlan-id 3508 Up 3.3.3.3 3508 131081 Up lg id 25 vlan-id 3509 Up 3.3.3.3 3509 131082 Up lg id 25 vlan-id 3510 Up 3.3.3.3 3510 131083 Up lg id 25 vlan-id 3511 Up 3.3.3.3 3511 131084 Up lg id 25 vlan-id 3512 Up 3.3.3.3 3512 131085 Up lg id 25 vlan-id 3513 Up 3.3.3.3 3513 131086 Up lg id 25 vlan-id 3514 Up 3.3.3.3 3514 131087 Up lg id 25 vlan-id 3515 Up 3.3.3.3 3515 131088 Up lg id 25 vlan-id 3516 Up 3.3.3.3 3516 131089 Up lg id 25 vlan-id 3517 Up 3.3.3.3 3517 131090 Up lg id 25 vlan-id 3518 Up 3.3.3.3 3518 131091 Up ---(more)---
The following table describes the fields in the show xc up command output.
Field |
Description |
---|---|
L2 Circuit |
Displays the circuit type and identifier for the physical (Layer 2) circuit hosting the local end of the XC, in the following format:
|
L2 State |
Current state of the Layer 2 (physical) circuit. Can be Up (circuit is active) or Down (circuit is inactive). |
Peer address |
IP address of the peer router. |
VC Id |
Virtual circuit identifier for the local end of the XC. |
L-Label |
Local label. Inner label associated with the local end of an L2VPN cross-connection. |
State |
Current state of the VC. Can be Up (circuit is active) or Down (circuit is inactive). |
The following example displays output from the show xc up detail command:
[local]Redback>show xc up detail LDP L2VPN Circuit lg id 25 vlan-id 58 L2 State : Up Peer : 3.3.3.3 VC ID : 102 XC state : Up Local Label : 131072 Access Circuit : 255/22:1:26/1/2/6 Remote Label : 131126 L2VPN Circuit : 255/12:103:63/0/1/1 EXP bits : 0 Local Encap : dot1q tsp Remote Group ID : 0 Remote Encap : Local VC Type : VLAN Remote VC Type : VLAN Local VC MTU : 1500 Remote VC MTU : 1500 Local VC Status : forwarding Remote VC Status : forwarding XC group : default Negotiated cbit : no LSP Configured : LSP Used : XC profile : Flags 0x800819e9: in-rib, in-lblmap, in-ldp, from-ldp, from-cfg : peer-up LDP L2VPN Circuit lg id 25 vlan-id 54:1 L2 State : Up Peer : 3.3.3.3 VC ID : 103 XC state : Up Local Label : 131073 Access Circuit : 255/22:1:26/1/2/15 ---(more)---
The following table describes the fields in the show xc up detail command.
Field |
Description |
---|---|
L2 State |
Current state of the layer 2 (physical) circuit. Can be Up (active) or Down (inactive). |
VC ID |
Identifies the virtual circuit on which this XC is configured. |
Local Label |
Inner label associated with the local end of an L2VPN cross-connection. |
Remote Label |
Inner label associated with the remote end of an L2VPN cross-connection. |
EXP bits |
EXP bits to be used for transport. Range is from 0 through 7. |
Remote Group ID |
Identifies the link group hosting this XC at the remote end (if the XC is configured under a link group). |
Local VC Type |
Type of circuit hosting the local end of the XC. |
Local VC MTU |
MTU on the local end of the XC. |
Local VC Status |
Indicates whether the VC hosting the local end of this XC is actively forwarding traffic or down. |
LSP Configured |
Name of the LSP mapped to the XC (if the XC is configured on an LSP). |
XC profile |
Identifies any XC profile that is attached to this XC. The XC profile determines the configuration used by the XC. |
XC group |
Identifies the group under which the local end of the XC is configured. |
Peer |
IP address of the peer hosting the remote end of the XC. |
XC state |
Current state of the XC. Can be Up (active) or Down (inactive). |
Access Circuit |
Circuit handle internally assigned to the local access circuit on the XC. |
L2VPN Circuit |
Circuit handle internally assigned to the L2VPN circuit. |
Local Encap |
Type of encapsulation on the local end of the XC. Can be:
|
Remote Encap |
Type of encapsulation on the remote end of the XC. Can be:
|
Remote VC Type |
Type of virtual circuit hosting the remote end of the XC. Can be VLAN, VPI-VCI, or PPPoE. |
Remote VC MTU |
MTU on the circuit hosting the remote end of the XC. |
Remote VC Status |
Current forwarding status of the VC hosting the remote end of the XC. Can be forwarding traffic (Up) or inactive (Down). |
Negotiated cbit |
Indicates whether the control word is present in the pseudowire PDU. The presence of a sequence number indicates that the control word is present in the pseudowire PDU. If the negotiated value is set to yes, then only the control word is present in the PDU that is carried over the pseudowire. |
LSP Used |
Indicates whether the control word is present in the pseudowire PDU. The presence of a sequence number indicates that the control word is present in the pseudowire PDU. If the negotiated value is set to yes, then only the control word is present in the PDU that is carried over the pseudowire. |
Flags 0x800819e9: |
Identifies the current running state of the XC. |