| Copyright |
© Ericsson AB 2009–2011. All rights reserved. No part of this document may be reproduced in any form without the written permission of the copyright owner. | ||||||
| Disclaimer |
The contents of this document are subject to revision without notice due to continued progress in methodology, design and manufacturing. Ericsson shall have no liability for any error or damage of any kind resulting from the use of this document. | ||||||
| Trademark List |
|
1 Command Descriptions
Commands starting with “show p” through commands starting with “show q” are included.
1.1 show pim bsr-router
show pim bsr-router
1.1.1 Purpose
Displays bootstrap router (BSR) and candidate rendezvous point (C-RP) information.
1.1.2 Command Mode
All modes
1.1.3 Syntax Description
This command has no keywords or arguments.
1.1.4 Default
None
1.1.5 Usage Guidelines
Use the show pim bsr-router command to display BSR and C-RP information.
- Note:
- By default, most show commands (in any mode) display information for the current context only or, depending on the command syntax, for all contexts. If you are an administrator for the local context, you can insert the optional context ctx-name construct, preceding the show command, to view output for the specified context without entering that context. For more information about using the context ctx-name construct, see the context command description.
- Note:
- By appending a space followed by the pipe ( | ) character at the end of a show command, you can filter the output using a set of modifier keywords and arguments. For more information, see Modifying Output of show Commands in Using the CLI.
1.1.6 Examples
The following example displays information for all BSRs and C-RPs:
[local]Redback>show pim bsr-router
PIM Bootstrap Information BSR address: 11.1.1.1 Uptime: 3d06h, BSR Priority: 0, Hash mask length: 0 Next Bootstrap: 00:00:37 Next Candidate RP advertisement in 00:00:42 RP: 11.1.1.1(fxp1), Group Acl:
1.2 show pim circuit
show pim circuit
1.2.1 Purpose
Displays circuit-specific information for Protocol Independent Multicast (PIM).
1.2.2 Command Mode
All modes
1.2.3 Syntax Description
This command has no keywords or arguments.
1.2.4 Default
None
1.2.5 Usage Guidelines
Use the show pim circuit command to display circuit-specific information for PIM.
- Note:
- By default, most show commands (in any mode) display information for the current context only or, depending on the command syntax, for all contexts. If you are an administrator for the local context, you can insert the optional context ctx-name construct, preceding the show command, to view output for the specified context without entering that context. For more information about using the context ctx-name construct, see the context command description.
- Note:
- By appending a space followed by the pipe ( | ) character at the end of a show command, you can filter the output using a set of modifier keywords and arguments. For more information, see “Modifying Output of show Commands” in Using the CLI.
1.2.6 Examples
The following example displays circuit-specific information for PIM:
[local]Redback>show pim circuit
Number of circuits: 4
1/9:1023:63/1/1/5, fxp1, Up, recv permit/send permit/unsol permit
1/11:1023:63/1/1/13, fxp2, Up, recv permit/send permit/unsol permit
12/1:1:63/1/2/18, fxp3, Up, recv permit/send permit/unsol permit
12/1:1:63/1/2/19, fxp3, Up, recv permit/send permit/unsol permit
1.3 show pim interface
show pim interface [if-name]
1.3.1 Purpose
Displays Protocol Independent Multicast (PIM)-enabled interface information.
1.3.2 Command Mode
All modes
1.3.3 Syntax Description
|
if-name |
Optional. Name of the PIM interface. |
1.3.4 Default
None
1.3.5 Usage Guidelines
Use the show pim interface command to display PIM-enabled interface information.
- Note:
- By default, most show commands (in any mode) display information for the current context only or, depending on the command syntax, for all contexts. If you are an administrator for the local context, you can insert the optional context ctx-name construct, preceding the show command, to view output for the specified context without entering that context. For more information about using the context ctx-name construct, see the context command description.
- Note:
- By appending a space followed by the pipe ( | ) character at the end of a show command, you can filter the output using a set of modifier keywords and arguments. For more information, see “Modifying Output of show Commands” in Using the CLI.
1.3.6 Examples
The following example displays information for all PIM-enabled interfaces:
[local]Redback>show pim interface
Address Interface Mode Cct Up Nbr Hello DR BFD
Count Dn Count Intvl
10.2.1.17 E1 sparse 0 Dn 0 30 10.2.1.17 Enabled
11.1.1.1 E2 sparse 0 Dn 0 30 11.1.1.1 Enabled
1.4 show pim mdt
show pim mdt
1.4.1 Purpose
Displays multicast domain tree (MDT) information.
1.4.2 Command Mode
All modes
1.4.3 Syntax Description
This command has no keywords or arguments.
1.4.4 Default
None
1.4.5 Usage Guidelines
Use the show pim mdt command to display MDT information.
The output from this command is context-specific.
The output in a Virtual Private Network (VPN) context shows the MDT group, the source for the VPN, and the context ID only for that VPN context. The output in local context lists MDT information for all VPNs.
- Note:
- By default, most show commands (in any mode) display information for the current context only or, depending on the command syntax, for all contexts. If you are an administrator for the local context, you can insert the optional context ctx-name construct, preceding the show command, to view output for the specified context without entering that context. For more information about using the context ctx-name construct, see the context command description.
- Note:
- By appending a space followed by the pipe ( | ) character at the end of a show command, you can filter the output using a set of modifier keywords and arguments. For more information, see “Modifying Output of show Commands” in Using the CLI.
1.4.6 Examples
The following example displays MDT information for a VPN-enabled context, VPN1:
[VPN1]Redback>show pim mdt Multicast Domain Tree information MDT Group Interface Source Context 239.1.1.1 ic-local lo1 0x40080002
The following example displays MDT information for all VPNs:
[local]Redback>show pim mdt Multicast Domain Tree information MDT Group Interface Source Context 239.1.1.1 ic-vpn1 lo1 0x40080002 196.1.1.1 ic-vpn2 lo2 0x40080003 10.10.1.1 ic-vpn3 lo3 0x40080004
1.5 show pim neighbor
show pim neighbor
1.5.1 Purpose
Displays Protocol Independent Multicast (PIM) neighbor information.
1.5.2 Command Mode
All modes
1.5.3 Syntax Description
This command has no keywords or arguments.
1.5.4 Default
None
1.5.5 Usage Guidelines
Use the show pim neighbor command to display PIM neighbor information.
- Note:
- By default, most show commands (in any mode) display information for the current context only or, depending on the command syntax, for all contexts. If you are an administrator for the local context, you can insert the optional context ctx-name construct, preceding the show command, to view output for the specified context without entering that context. For more information about using the context ctx-name construct, see the context command description.
- Note:
- By appending a space followed by the pipe ( | ) character at the end of a show command, you can filter the output using a set of modifier keywords and arguments. For more information, see “Modifying Output of show Commands” in Using the CLI.
1.5.6 Examples
The following example displays information about all PIM neighbors:
[local]Redback>show pim neighbor
PIM Neighbor Table Neighbor Address Interface Uptime Expire DR hex Prio hex GenID DR SR intvl Bfd Status 10.4.1.2 fxp1 00:04:10 00:01:34 0x1 0x17ac7e7a Y 60 Up 10.5.1.4 fxp2 00:25:22 00:01:22 0x1 0x18ab6e6a Y 60 Up
1.6 show pim ppa
show pim ppa
1.6.1 Purpose
Displays the Packet Processing ASIC (PPA) state from the Protocol Independent Multicast (PIM) perspective.
1.6.2 Command Mode
All modes
1.6.3 Syntax Description
This command has no keywords or arguments.
1.6.4 Default
None
1.6.5 Usage Guidelines
Use the show pim ppa command to display the PPA state from the PIM perspective.
- Note:
- By default, most show commands (in any mode) display information for the current context only or, depending on the command syntax, for all contexts. If you are an administrator for the local context, you can insert the optional context ctx-name construct, preceding the show command, to view output for the specified context without entering that context. For more information about using the context ctx-name construct, see the context command description.
- Note:
- By appending a space followed by the pipe ( | ) character at the end of a show command, you can filter the output using a set of modifier keywords and arguments. For more information, see “Modifying Output of show Commands” in Using the CLI.
1.6.6 Examples
The following example displays output from the show pim ppa command:
[local]Redback>show pim ppa
Slot 2 IPCs sent :1 Circuit enable/disable:8/0
ePPA IPCs rcvd :1 IPC failures:0
IPC blocked:NO Num of IPCs blocked:1
Status :UP Restarts: 1
Up/Dn time :17:05:19 Multicast Interfaces:4
Version :54 Goal Version:54
Slot 2 IPCs sent :1 Circuit enable/disable:8/0
iPPA IPCs rcvd :1 IPC failures:0
IPC blocked:NO Num of IPCs blocked:1
Status :UP Restarts: 1
Up/Dn time :17:05:19 Multicast Interfaces:4
Version :54 Goal Version:54
Slot 11 IPCs sent :1 Circuit enable/disable:14/0
ePPA IPCs rcvd :1 IPC failures:0
IPC blocked:NO Num of IPCs blocked:1
Status :UP Restarts: 1
Up/Dn time :17:05:19 Multicast Interfaces:7
Version :54 Goal Version:54
1.7 show pim rpf
show pim rpf {src-addr | src-name}
1.7.1 Purpose
Displays reverse path forwarding (RPF) statistics for a specified multicast source.
1.7.2 Command Mode
All modes
1.7.3 Syntax Description
|
src-addr |
IP address of a multicast source. |
|
src-name |
Name of a multicast source. |
1.7.4 Default
None
1.7.5 Usage Guidelines
Use the show pim rpf command to display RPF statistics for a specified multicast source.
- Note:
- By default, most show commands (in any mode) display information for the current context only or, depending on the command syntax, for all contexts. If you are an administrator for the local context, you can insert the optional context ctx-name construct, preceding the show command, to view output for the specified context without entering that context. For more information about using the context ctx-name construct, see the context command description.
- Note:
- By appending a space followed by the pipe ( | ) character at the end of a show command, you can filter the output using a set of modifier keywords and arguments. For more information, see “Modifying Output of show Commands” in Using the CLI.
1.7.6 Examples
The following example displays output from the show pim rpf command:
[local]Redback>show pim rpf 11.1.1.1
RPF information for 11.1.1.1 RPF interface: fxp1 RPF neighbor: 102.1.1.1 RPF route/mask: 11.1.1.0/255.255.255.0 RPF type: mbgp
1.8 show pim rp-hash
show pim rp-hash group-addr
1.8.1 Purpose
Displays information about the rendezvous point (RP) to which the specified Internet Group Management Protocol (IGMP) group hashes.
1.8.2 Command Mode
All modes
1.8.3 Syntax Description
|
group-addr |
IP address of the IGMP group. |
1.8.4 Default
None
1.8.5 Usage Guidelines
Use the show pim rp-hash command to display information about the RP to which the specified group hashes (maps).
- Note:
- By default, most show commands (in any mode) display information for the current context only or, depending on the command syntax, for all contexts. If you are an administrator for the local context, you can insert the optional context ctx-name construct, preceding the show command, to view output for the specified context without entering that context. For more information about using the context ctx-name construct, see the context command description.
- Note:
- By appending a space followed by the pipe ( | ) character at the end of a show command, you can filter the output using a set of modifier keywords and arguments. For more information, see “Modifying Output of show Commands” in Using the CLI.
1.8.6 Examples
The following example displays information about the RP to which the group, 224.121.121.1, hashes:
[local]Redback>show pim rp-hash 224.121.121.1
RP 10.6.1.2
Info source: 10.4.1.2, via Bootstrap
Uptime: 00:05:00, expires: 00:02:58
1.9 show pim rp mapping
show pim rp mapping [group-addr]
1.9.1 Purpose
Displays a group-to-rendezvous point (RP) mapping cache.
1.9.2 Command Mode
All modes
1.9.3 Syntax Description
|
group-addr |
Optional. IP address of the Internet Group Management Protocol (IGMP) group. |
1.9.4 Default
None
1.9.5 Usage Guidelines
Use the show pim rp mapping command to display a group-to-RP mapping cache.
- Note:
- By default, most show commands (in any mode) display information for the current context only or, depending on the command syntax, for all contexts. If you are an administrator for the local context, you can insert the optional context ctx-name construct, preceding the show command, to view output for the specified context without entering that context. For more information about using the context ctx-name construct, see the context command description.
- Note:
- By appending a space followed by the pipe ( | ) character at the end of a show command, you can filter the output using a set of modifier keywords and arguments. For more information, see Modifying Output of show Commands in Using the CLI.
1.9.6 Examples
The following example displays the group-to-RP mapping cache:
[local]Redback>show pim rp mapping
PIM Group-to-RP Mappings
Group(s) 224.24.0.0/16
RP 10.6.1.2
Info source: 10.4.1.2, via Bootstrap
Uptime: 00:04:41, expires: 00:02:17
Group(s) 224.121.0.0/16
RP 10.6.1.2
Info source: 10.4.1.2, via Bootstrap
Uptime: 00:04:41, expires: 00:02:17
1.10 show pim ssm
show pim ssm
1.10.1 Purpose
Displays the Source-Specific Multicast (SSM) setting in Protocol Independent Multicast (PIM).
1.10.2 Command Mode
All modes
1.10.3 Syntax Description
This command has no keywords or arguments.
1.10.4 Default
None
1.10.5 Usage Guidelines
Use the show pim ssm command to display the SSM setting in PIM.
- Note:
- By default, most show commands (in any mode) display information for the current context only or, depending on the command syntax, for all contexts. If you are an administrator for the local context, you can insert the optional context ctx-name construct, preceding the show command, to view output for the specified context without entering that context. For more information about using the context ctx-name construct, see the context command description.
- Note:
- By appending a space followed by the pipe ( | ) character at the end of a show command, you can filter the output using a set of modifier keywords and arguments. For more information, see Modifying Output of show Commands in Using the CLI.
1.10.6 Examples
The following example displays output from the show pim ssm command:
[local]Redback>show pim ssm
Source Specific Multicast (SSM) setting SSM address range: default (232.0.0.0/8)
1.11 show pim traffic
show pim traffic
1.11.1 Purpose
Displays Protocol Independent Multicast (PIM) traffic statistics.
1.11.2 Command Mode
All modes
1.11.3 Syntax Description
This command has no keywords or arguments.
1.11.4 Default
None
1.11.5 Usage Guidelines
Use the show pim traffic command to display PIM traffic statistics.
- Note:
- By default, most show commands (in any mode) display information for the current context only or, depending on the command syntax, for all contexts. If you are an administrator for the local context, you can insert the optional context ctx-name construct, preceding the show command, to view output for the specified context without entering that context. For more information about using the context ctx-name construct, see the context command description.
- Note:
- By appending a space followed by the pipe ( | ) character at the end of a show command, you can filter the output using a set of modifier keywords and arguments. For more information, see Modifying Output of show Commands in Using the CLI.
1.11.6 Examples
The following example displays PIM traffic statistics:
[local]Redback>show pim traffic
PIM statistics:
Sent:
Total 0, Hello 217, Register 0, Register-Stop 0, Join/Prune 5,
BSR 21, Assert 0, Graft 0, Graft-ack 0, Candidate-RP-advertisement 0
PIMv1: Register 0, Register-Stop 0
Received:
Total 0, Hello 66, Register 0, Register-Stop 0, Join/Prune 0,
BSR 12, Assert 0, Graft 0, Graft-ack 0, Candidate-RP-advertisement 0
PIMv1: Register 0, Register-Stop 0, Punts 21
Error:
Hello 0, Register 0, Register-Stop 0, Join/Prune 0,
BSR 0, Assert 0, Graft 0, Graft-ack 0, Candidate-RP-advertisement 0
PIMv1: Register 0, Register-Stop 0
I/O errors 0, Short packets 0, Checksum 0
Unknown type: 0
Queue:
Input queue size 0, Input queue overflows 0
1.12 show policy access-list
show policy access-list [{[summary] [acl-name] | first-match acl-name [protocol] {src-addr [port port]} [dest-addr [port port]}] [dscp dscp-value] [length length] [precedence prec-value] [tos tos-value]
1.12.1 Purpose
Displays the status of configured policy access control lists (ACLs).
1.12.2 Command Mode
All modes
1.12.3 Syntax Description
|
summary |
Optional. Excludes the ACL statements from the display. Optionally, you can follow this keyword with the acl-name argument, naming a particular ACL for which you want summary information displayed. |
|
acl-name |
Optional. Name of the ACL for which you want information displayed. To display summary information about a specific list, you must enter the summary keyword first, followed by the acl-name argument. |
|
first-match acl-name |
Optional. Name of the ACL for which you want to find the first statement matched by the criteria that follows the first-match acl-name construct. |
|
protocol |
Optional. Number indicating a protocol as specified in RFC 1700, Assigned Numbers. The range of values is 0 to 255. In place of the protocol argument, you can use any of the following keywords:
|
|
src-addr |
Source address to be included in the criteria for a match. An IP address in the form A.B.C.D. |
|
port port |
Optional. TCP or UDP port to be considered a match for either the source or destination IP address. This construct is only available if you specified TCP or UDP as the protocol. The range of values is 1 to 65,535. You can also substitute a keyword for the port argument as listed in Table 1 and Table 2 in the Usage Guidelines section for this command. |
|
dest-addr |
Optional. Destination address to be included in the criteria for a match. An IP address in the form A.B.C.D. |
|
dscp dscp-value |
Optional. Differentiated Services Code Point (DSCP) to be included in the criteria for a match. The range of values is 0 to 63. You can also substitute a keyword for the dscp-value argument as listed in Table 3 in the Usage Guidelines section for this command. |
|
length length |
Optional. Packet length. The length of the network-layer packet, beginning with the IP header. The range of values is 20 to 65,535. |
|
precedence prec-value |
Optional. Precedence value of packets to be included in the criteria for a match. The range of precedence values is 0 to 7. In place of the prec-value argument, you can enter any of the following keywords:
|
|
tos tos-value |
Optional. Type of service (ToS) to be included in the criteria for a match. The range of values is 0 to 15. In place of the tos-value argument, you can enter any of the following keywords:
To specify both a precedence and a ToS, you must enter the precedence prec-value construct first, followed by the tos tos-value construct. |
1.12.4 Default
When entered without any optional syntax, the show policy access-list command displays information for all policy ACLs in the context, including the statements in each list.
1.12.5 Usage Guidelines
Use the show policy access-list command to display the status of configured policy ACLs.
Use the first-match acl-name construct to display the first statement in the policy ACL that is matched by the criteria that follows the first-match acl-name construct.
Table 1 lists the valid keyword substitutions for the port argument when the argument is used to specify a TCP port.
|
Keyword |
Definition |
Corresponding Port Number |
|---|---|---|
|
bgp |
Border Gateway Protocol |
179 |
|
chargen |
Character generator |
19 |
|
cmd |
Remote commands (rcmd) |
514 |
|
daytime |
Daytime |
13 |
|
discard |
Discard |
9 |
|
domain |
Domain Name System |
53 |
|
echo |
Echo |
7 |
|
exec |
Exec (rsh) |
512 |
|
finger |
Finger |
79 |
|
ftp |
File Transfer Protocol |
21 |
|
ftp-data |
FTP data connections (used infrequently) |
20 |
|
gopher |
Gopher |
70 |
|
hostname |
Network interface card (NIC) hostname server |
101 |
|
ident |
Identification protocol |
113 |
|
irc |
Internet Relay Chat |
194 |
|
klogin |
Kerberos login |
543 |
|
kshell |
Kerberos Shell |
544 |
|
login |
Login (rlogin) |
513 |
|
lpd |
Printer service |
515 |
|
nntp |
Network News Transport Protocol |
119 |
|
pim-auto-rp |
Protocol Independent Multicast Auto-RP |
496 |
|
pop2 |
Post Office Protocol Version 2 |
109 |
|
pop3 |
Post Office Protocol Version 3 |
110 |
|
shell |
Remote Command Shell |
514 |
|
smtp |
Simple Mail Transport Protocol |
25 |
|
ssh |
Secure Shell |
22 |
|
sunrpc |
Sun Remote Procedure Call |
111 |
|
syslog |
Syslog |
514 |
|
tacacs |
Terminal Access Controller Access Control System |
49 |
|
talk |
Talk |
517 |
|
telnet |
Telnet |
23 |
|
time |
Time |
37 |
|
uucp |
Unix-to-Unix Copy Program |
540 |
|
whois |
Nickname |
43 |
|
www |
World Wide Web (HTTP) |
80 |
Table 2 lists the valid keyword substitutions for the port argument when the argument is used to specify a UDP port.
|
Keyword |
Definition |
Corresponding Port Number |
|---|---|---|
|
biff |
Biff (Mail Notification, Comsat) |
512 |
|
bootpc |
Bootstrap Protocol client |
68 |
|
bootps |
Bootstrap Protocol server |
67 |
|
discard |
Discard |
9 |
|
dnsix |
DNSIX Security Protocol Auditing |
195 |
|
domain |
Domain Name System |
53 |
|
echo |
Echo |
7 |
|
isakmp |
Internet Security Association and Key Management Protocol (ISAKMP) |
500 |
|
mobile-ip |
Mobile IP registration |
434 |
|
nameserver |
IEN116 Name Service (obsolete) |
42 |
|
netbios-dgm |
NetBIOS Datagram Service |
138 |
|
netbios-ns |
NetBIOS Name Service |
137 |
|
netbios-ss |
NetBIOS Session Service |
139 |
|
ntp |
Network Time Protocol |
123 |
|
pim-auto-rp |
Protocol Independent Multicast Auto-RP |
496 |
|
rip |
Router Information Protocol |
520 |
|
snmp |
Simple Network Management Protocol |
161 |
|
snmptrap |
SNMP traps |
162 |
|
sunrpc |
Sun Remote Procedure Call |
111 |
|
syslog |
System logger |
514 |
|
tacacs |
Terminal Access Controller Access Control System |
49 |
|
talk |
Talk |
517 |
|
tftp |
Trivial File Transfer Protocol |
69 |
|
time |
Time |
37 |
|
who |
Who Service (rwho) |
513 |
|
xdmcp |
X Display Manager Control Protocol |
177 |
Table 3 lists the valid keyword substitutions for the dscp-value argument.
|
Keyword |
Definition |
|---|---|
|
af11 |
Assured Forwarding—Class 1/Drop Precedence 1 |
|
af12 |
Assured Forwarding—Class 1/Drop Precedence 2 |
|
af13 |
Assured Forwarding—Class 1/Drop Precedence 3 |
|
af21 |
Assured Forwarding—Class 2/Drop Precedence 1 |
|
af22 |
Assured Forwarding—Class 2/Drop Precedence 2 |
|
af23 |
Assured Forwarding—Class 2/Drop Precedence 3 |
|
af31 |
Assured Forwarding—Class 3/Drop Precedence 1 |
|
af32 |
Assured Forwarding—Class 3/Drop Precedence 2 |
|
af33 |
Assured Forwarding—Class 3/Drop Precedence 3 |
|
af41 |
Assured Forwarding—Class 4/Drop Precedence 1 |
|
af42 |
Assured Forwarding—Class 4/Drop Precedence 2 |
|
af43 |
Assured Forwarding—Class 4/Drop Precedence 3 |
|
cs0 |
Class Selector 0 |
|
cs1 |
Class Selector 1 |
|
cs2 |
Class Selector 2 |
|
cs3 |
Class Selector 3 |
|
cs4 |
Class Selector 4 |
|
cs5 |
Class Selector 5 |
|
cs6 |
Class Selector 6 |
|
cs7 |
Class Selector 7 |
|
df |
Default Forwarding (same as cs0) |
|
ef |
Expedited Forwarding |
- Note:
- By default, most show commands (in any mode) display information for the current context only or, depending on the command syntax, for all contexts. If you are an administrator for the local context, you can insert the optional context ctx-name construct, preceding the show command, to view output for the specified context without entering that context. For more information about using the context ctx-name construct, see the context command description.
- Note:
- By appending a space followed by the pipe ( | ) character at the end of a show command, you can filter the output using a set of modifier keywords and arguments. For more information, see Modifying Output of show Commands in Using the CLI.
1.12.6 Examples
The following example displays information about the policy ACL, diff-serve:
[local]Redback>show policy access-list diff-serve policy access-list diff-serve: count 4, sequences: 10 - 40 client count: 0 modified: 00:03:08 (hh:mm:ss) ago seq 10 permit tcp any eq telnet class Expedited_Flow seq 20 permit ip any dscp eq ef class Expedited_Flow seq 30 permit tcp any eq ftp class Bulk_Data seq 40 permit udp any eq tftp class Bulk_Data
The following example displays information about the policy ACL, redirect_acl:
[local]Redback>show policy access-list redirect_acl
policy access-list redirect_acl:
count: 3, sequences: 10 - 30, client count: 1
modified: 00:21:34 (hh:mm:ss) ago, version: 8
condition 101 time-range
periodic weekdays 00:00 to 23:59 class redir2
seq 10 permit tcp any any eq www class redir0 condition 101
seq 20 permit tcp any any eq 81 class redir1
seq 30 permit tcp any any eq 82 class redir2
The following example displays information about the policy ACL, qos1:
[local]Redback>show policy access-list qos1
policy access-list qos1:
count: 1, sequences: 10 - 10, client count: 1
modified: 00:08:35 (hh:mm:ss) ago, version: 4
condition 100 time-range
periodic weekdays 00:00 to 23:59 class redir2
seq 10 permit ip host 10.3.29.3 any class CLASS1 condition 100
1.13 show port
show port [all]
1.13.1 Purpose
Displays a list of ports that are present or configured in the system.
1.13.2 Command Mode
All modes
1.13.3 Syntax Description
|
all |
Optional. For any SmartEdge™ router except the SmartEdge 100 router, includes ports that are configured but are not present on the system. For SmartEdge 100 routers, displays all ports on the carrier card, regardless of whether the associated media interface cards (MICs) are available. |
|
all |
Optional. Includes ports that are configured but are not present on the system. |
1.13.4 Default
Displays only ports that are present on the system.
1.13.5 Usage Guidelines
Use the show port command to display a list of ports that are present or configured in the system.
Table 4 describes the values for the State field that can be displayed for a given port on a SmartEdge 400 or SmartEdge 800 router.
|
State |
Description |
|---|---|
|
Up |
Port is configured to be up, and it is up. |
|
Down |
Port is configured, and it is down. |
|
Down—not entitled |
Port is on the low-density version of the line card and is not available. |
|
Unconfigured |
Port is unconfigured and down. |
Table 5 describes the values for the State field that can be displayed for a given port on a SmartEdge 100 router.
|
State |
Description |
|---|---|
|
Up |
The carrier card and associated MIC are configured and physically present. The port is configured and successfully passing traffic. |
|
Down |
The carrier card and associated MIC are configured and physically present. The port is configured but is not successfully passing traffic. |
|
No card |
The carrier card and associated MIC are configured but not physically present, and the specified port has been configured. |
|
No MIC |
The carrier card and associated MIC have been configured and the specified port has been configured, but the MIC is not physically present. |
|
Unavailable |
The carrier card is configured and may or may not be physically present, but either the associated MIC has not been configured or the configured MIC does not support the specified port. |
|
Unconfigured |
The carrier card and associated MIC are configured and may or may not be physically present, but the specified port has not been configured. |
- Note:
- By default, most show commands (in any mode) display information for the current context only or, depending on the command syntax, for all contexts. If you are an administrator for the local context, you can insert the optional context ctx-name construct, preceding the show command, to view output for the specified context without entering that context. For more information about using the context ctx-name construct, see the context command description.
- Note:
- By appending a space followed by the pipe ( | ) character at the end of a show command, you can filter the output using a set of modifier keywords and arguments. For more information, see Modifying Output of show Commands in Using the CLI.
|
Field Name |
Value/Description |
|---|---|
|
Slot/Port |
slot/port—Slot and port numbers for this port. |
|
Ch:SubCh:SubSubCh |
Channel numbers, if appropriate for this port: |
|
Type |
port-type or channel-type. |
|
State |
Port status (combination of the Admin state and Line state fields): |
|
Port Type |
Description |
|---|---|
|
atm |
ATM port |
|
pos |
POS port |
|
ethernet |
Ethernet or GE port (any version) |
|
transceiver |
SFP or XFP transceivers port |
|
channelized-oc3 |
Channelized OC-3 port |
|
channelized-oc12 |
Channelized OC-12 port |
|
channelized-stm1 |
Channelized STM-1 port |
|
channelized-stm4 |
Channelized STM-4 port |
|
Port/Channel Type |
Description |
|---|---|
|
Port types |
Type of ports:
|
|
Channel types |
Type of channels:
|
1.13.6 Examples
The following example displays the list of all ports that are present in a SmartEdge 800 router.
In this example, the 4-port Gigabit Ethernet line card is a low-density, 2-port version; ports 2 and 4 are unavailable:
[local]Redback>show port all Slot/Port:Ch.SubCh Type State 2/1 oc12 Unconfigured 2/2 oc12 Unconfigured 2/3 oc12 Unconfigured 2/4 oc12 Unconfigured 4/1 ethernet Up 4/2 ethernet Up 4/3 ethernet Up 4/4 ethernet Up 7/1 ethernet Up 9/1 ethernet Up 9/2 ethernet Down - not entitled 9/3 ethernet Up 9/4 ethernet Down - not entitled
1.14 show port counters
For all other line cards and all media interface cards (MICs), the syntax is:
show port counters [persistent] [slot/port] [detail | live | queue]
1.14.1 Purpose
Displays the counters associated with system ports and channels.
1.14.2 Command Mode
All modes
1.14.3 Syntax Description
|
persistent |
Optional. If omitted, displays values since the counters were last cleared or the card was last reloaded. If specified, displays values since the system was last reloaded. |
|
slot |
Optional. Chassis slot number of the line card for which counters are displayed. |
|
port |
Required if you enter the slot argument. Port number for which counters are displayed. The range of values depends on the type of card or MIC. |
|
chan-num |
Optional. Channel number or which counters are displayed. If omitted, displays counters for all channels on the specified port. The range of values depends on the type of port. |
|
sub-chan-num |
Optional. Subchannel number channel for which counters are displayed. If omitted, displays counters for all subchannels in the specified channel. The range of values depends on the type of port. |
|
detail |
Optional. Displays more detailed counter information. |
|
live |
Optional. Forces the retrieval of live data for summary counters. |
|
queue |
Optional. Displays per-queue information kept by Packet Processing ASIC (PPA) counters; the values reflect the count since the last policy change. |
1.14.4 Default
Displays last known values of summary counters for all ports.
1.14.5 Usage Guidelines
Use the show port counters command to display counters associated with system ports with values that have been accumulated since the counters were last cleared with the clear port counters command (in exec mode) or the line card was last reloaded.
Use the persistent keyword to display the counters with values accumulated since the system was last reloaded.
If you specify the optional slot, or port, or chan-num arguments, the display shows counter information for the specified line card, or port, or channel; if you specify the optional sub-chan-num argument, the output displays counter information for just that subchannel.
By default, this command displays only summary counter information for all ports with their last known values, which have been cached; cached values are updated every 60 seconds. Use the live keyword to force the system to read and display the current values for the summary counters.
Table 9 describes the summary counter information that is displayed for all port types if the detail keyword is not specified.
|
Field |
Description |
|---|---|
|
packets sent |
Number of packets sent |
|
packets recvd |
Number of packets received |
|
send packet rate |
Number of packets per second sent |
|
recv packet rate |
Number of packets per second received |
|
rate refresh interval |
Applies only to rate counters; interval (seconds) over which rates have been calculated |
|
bytes sent |
Number of bytes sent |
|
bytes recvd |
Number of bytes received |
|
send bit rate |
Number of bits per second sent |
|
recv bit rate |
Number of bits per second received |
Table 10 describes the PPA and packet drop counters, which are displayed for all types of ports when you specify the detail keyword; the data displayed for these counters, with the exception of the rate counters, is live, not cached data.
|
Field |
Description |
|---|---|
|
PPA Port Counters | |
|
packets sent |
Number of packets sent |
|
packets recvd |
Number of packets received |
|
send packet rate |
Number of packets per second sent |
|
recv packet rate |
Number of packets per second received |
|
IP mcast pks rcv |
Number of multicast packets received |
|
IP mcast pks snt |
Number of multicast packets sent |
|
rate refresh interval |
Applies only to rate counters; interval (seconds) over which rates have been calculated |
|
bytes sent |
Number of bytes sent |
|
bytes recvd |
Number of bytes received |
|
send bit rate |
Number of bits per second sent |
|
recv bit rate |
Number of bits per second received |
|
IP mcast bytes rcv |
Number of multicast bytes received |
|
IP mcast bytes snt |
Number of multicast bytes sent |
|
PPA Input Error Counters | |
|
idc other errors |
Number of packets received with other errors, as reported by the FPGA |
|
idc overrun errors |
Number of packets received that overran the input descriptor cache |
|
no cct packets |
Number of packets received that do not belong to any circuit |
|
cct down pkts |
Number of packets dropped because the circuit is down |
|
unknown encap pkts |
Number of packets received for which the packet encapsulation is incorrect for the circuit |
|
unreach pkts |
Number of packets dropped because no destination route entry exists for the destination IP address |
|
media filter pkts |
Number of packets with an unsupported media protocol |
|
crc port errors |
Number of packets received with CRC errors |
|
idc abort errors |
Number of packets received with a line-signaled abort |
|
no cct bytes |
Number of bytes received that do not belong to any circuit |
|
cct down bytes |
Number of bytes dropped because the circuit is down |
|
unknown encap byte |
Number of bytes received for which the byte encapsulation is incorrect for the circuit |
|
unreach bytes |
Number of bytes dropped because no destination route entry exists for the destination IP address |
|
media filter bytes |
Number of bytes with an unsupported media protocol |
|
PPA Output Error Counters | |
|
WRED drop packets |
Number of packets dropped by the WRED feature |
|
adj drop packets |
Number of packets dropped due to adjacency errors or missing adjacency |
|
tail drop packets |
Number of packets dropped because the egress queue is full |
|
adj drop packets |
Number of bytes dropped due to adjacency errors or missing adjacency |
|
Packet Drop Counters | |
|
not IPv4 drop pkts |
Number of packets dropped that are marked with an unsupported IP version |
|
unhandled IP optns |
Number of packets dropped due to unsupported IP options |
|
bad IP checksum |
Number of packets dropped due to an invalid checksum on the packet |
|
link layer bcast |
Number of link layer broadcast packets dropped |
|
bad IP length |
Number of packets dropped due to an invalid checksum on the packet |
Table 11 describes the policing counters that are displayed for all types of ports, except for Ethernet ports, when you specify the detail keyword.
|
Field |
Description |
|---|---|
|
conform pkts |
Number of packets that conform to the rate-limiting policy on incoming traffic |
|
conform drop pkts |
Number of packets that conform to the rate-limiting policy but were dropped |
|
exceed pkts |
Number of packets that exceed the rate defined by the rate-limiting policy |
|
exceed drop pkts |
Number of packets that exceed the rate defined by the rate-limiting policy and were dropped |
|
conform bytes |
Number of bytes that conform to the rate-limiting policy on incoming traffic |
|
conform drop bytes |
Number of bytes that conform to the rate-limiting policy but were dropped |
|
exceed bytes |
Number of bytes that exceed the rate defined by the rate-limiting policy |
|
exceed drop bytes |
Number of bytes that exceed the rate defined by the rate-limiting policy and were dropped |
- Note:
- For counters for ATM ports:
- Per-queue information kept by PPA counters reflects the count since the last policy change.
- If a queuing algorithm is managed by the segmentation and reassembly controller (SARC) on an ATM line card, the counts reported by the PPA counters are zeros.
Table 12 describes the optical data that is displayed for POS optical ports when you specify the detail keyword.
|
Field |
Description |
|---|---|
|
Active Alarms |
Lists the active alarms, if any:
|
|
SONET Section | |
|
LOS |
Number of loss of signal occurrences detected by the section |
|
LOF |
Number of loss of frame occurrences detected by the section |
|
BIP-B1 |
Number of Bit Interleaved Parity error conditions (value of the B1 byte) detected by the section |
|
SONET Line | |
|
AIS |
Number of alarm indication signal occurrences detected by the line |
|
RDI |
Number of remote defect indication signal occurrences detected by the line |
|
BIP-B2 |
Number of Bit Interleaved Parity error conditions (value of the B2 byte) detected by the line |
|
FEBE |
Number of far end block error conditions detected by the line |
|
SONET Path | |
|
AIS |
Number of alarm indication signal occurrences detected by the path |
|
RDI |
Number of remote defect indication signal occurrences detected by the path |
|
BIP-B3 |
Number of Bit Interleaved Parity error conditions (value of the B3 byte) detected by the path |
|
FEBE |
Number of far end block error conditions detected by the path |
|
LOP |
Number of loss of pointer conditions detected by the path |
|
Received SONET Overhead | |
|
F1 |
Value of the F1 byte |
|
K1 |
Value of the K1 byte |
|
K2 |
Value of the K2 byte |
|
S1 |
Value of the S1 byte |
|
C2 |
Value of the C2 byte |
|
Transmitted SONET Overhead | |
|
F1 |
Value of the F1 byte |
|
K1 |
Value of the K1 byte |
|
K2 |
Value of the K2 byte |
|
S1 |
Value of the S1 byte |
|
C2 |
Value of the C2 byte |
Table 13 lists the general, transmit, and receive counters that are displayed for Ethernet ports when the detail keyword is specified. These counters are displayed in addition to the PPA and packet drop counters.
|
Field |
Description |
|---|---|
|
General Counters | |
|
packets sent |
Total number of multicast and broadcast packets transmitted without any errors |
|
bytes sent |
Number of bytes transmitted in good packets plus the number of bytes transmitted in packets with errors |
|
mcast packets sent |
Number of multicast packets that are transmitted without any errors |
|
bcast packets sent |
Number of broadcast packets transmitted without any errors |
|
dropped pkts out |
Number of packets dropped during transmission |
|
pending pkts out |
Number of packets queued during transmission |
|
port drops out |
Number of packets dropped on the egress port due to exceeding the rate limit as defined by the metering policy applied on that port |
|
packets recvd |
Total number of multicast and broadcast packets with lengths between 64 bytes and the maximum packet size received without any errors |
|
bytes recvd |
Number of bytes received in good packets plus the number of bytes received in packets with errors |
|
mcast packets recvd |
Number of multicast packets with lengths between 64 bytes and the maximum packet size received without any errors |
|
bcast packets recvd |
Number of broadcast packets with lengths between 64 bytes and the maximum packet size received without any errors |
|
dropped pkts in |
Number of packets dropped during reception |
|
pending pkts in |
Number of packets queued during reception |
|
port drops in |
Number of packets dropped on the ingress port due to exceeding the rate limit as defined by the metering policy applied on that port |
|
Transmit Counters | |
|
late collision |
Number of transmission abortions due to a collision occurring after transmission of packets that are 64 bytes in length |
|
underflow |
Number of packets transmitted with an error due to transmit FIFO underflow or txerr signal assertion |
|
regular collision |
Total number of regular collision events occurring during transmission |
|
single collision |
Number of packets transmitted without any error following a single collision |
|
multiple colls |
Number of packets transmitted without any error following multiple collisions |
|
excessive colls |
Number of packets that have experienced 16 consecutive collisions or more |
|
deferred |
Number of packets deferred upon the first transmit attempt due to a busy line |
|
flow control |
Number of correct transmitted flow-control packets |
|
error pkts sent |
Number of packets transmitted with an error due to transmit FIFO underflow or txerr signal assertion plus number of regular collision events occurring during transmission |
|
error bytes sent |
Number of bytes transmitted in packets with errors |
|
eth 64 octets |
Number of transmitted packets, 64 bytes in length, including bad packets |
|
eth 65-127 octs |
Number of transmitted packets, 65 to 127 bytes in length, including bad packets |
|
eth 128-255 octs |
Number of transmitted packets, 128 to 255 bytes in length, including bad packets |
|
eth 256-511 octs |
Number of transmitted packets, 256 to 511 bytes in length, including bad packets |
|
eth 512-1023 octs |
Number of transmitted packets, 512 to 1,023 bytes in length, including bad packets |
|
eth 1024-1518 octs |
Number of transmitted packets, 1,024 to 1,518 bytes in length, including bad packets |
|
eth > 1518 octs |
Number of transmitted packets with length larger than 1,519 bytes, including bad packets |
|
Receive Counters | |
|
jabber |
Number of packets, larger than the maximum packet size, received with a CRC error |
|
false carrier |
Number of false carriers |
|
runt frames |
Number of frames received without SFD detection but with carrier assertion |
|
undersized frames |
Number of packets, less than 64 bytes in length, received without any error |
|
oversized frames |
Number of packets, larger than the maximum packet size, received without any error |
|
crc errors |
Number of packets with lengths between 64 bytes and the maximum packet size, received with an integral number of bytes and a CRC error |
|
alignment errors |
Number of packets with lengths between 64 bytes and the maximum packet size, received with a non-integral number of bytes and a CRC error |
|
symbol errors |
Number of received packets during which PHY symbol errors were detected |
|
error pkts rcvd |
Total of the following counters:
|
|
error bytes rcvd |
Number of bytes received in packets with errors |
|
flow control |
Number of correct received flow-control packets |
|
overflows |
Number of receive packets not fully accepted due to receive FIFO overflow or ingress queue overflow |
|
overflow bytes |
Number of bytes not reported for all card types(1) |
|
eth 64 octets |
Number of received packets, 64 bytes in length, including bad packets |
|
eth 65-127 octs |
Number of received packets, 65 to 127 bytes in length, including bad packets |
|
eth 128-255 octs |
Number of received packets, 128 to 255 bytes in length, including bad packets |
|
eth 256-511 octs |
Number of received packets, 256 to 511 bytes in length, including bad packets |
|
eth 512-1023 octs |
Number of received packets, 512 to 1,023 bytes in length, including bad packets |
|
eth 1024-1518 octs |
Number of received packets, 1,024 to 1,518 bytes in length, including bad packets |
|
eth > 1518 octs |
Number of received packets with length larger than 1,519 bytes, including bad packets |
(1) This
field is only available for oversubscribable line cards that support
propagation of QoS at the port level.
Table 14 describes the Point-to-Point Protocol (PPP) over Ethernet (PPPoE) counters that are displayed for Ethernet ports.
|
Field |
Description |
|---|---|
|
control pkts |
Number of control packets received |
|
bad session pkts |
Number of session packets received with an invalid session ID |
|
padt sent pkts |
Number of PADT packets sent |
|
padr drop pkts |
Number of PADR packets dropped |
|
padi drop pkts |
Number of PADI packets dropped |
|
padt drop pkts |
Number of PADT packets dropped |
|
bad code pkts |
Number of unsupported PPPoE discovery packets received |
Table 15 describes the counters that are displayed for each queue for the ports specified by the input parameters when you specify the queue keyword. If no queue policy is attached to a port, no per-queue information is displayed.
|
Field |
Description |
|---|---|
|
Queue |
Queue number: 0 to 7 |
|
Depth |
Maximum number of packets allowed for this queue (configured) |
|
Pkts/Bytes Sent |
Packets and bytes sent on this queue |
|
WRED Drops |
Number of packets dropped by the WRED feature on this queue |
|
Tail Drops |
Number of packets dropped because this queue is full |
- Note:
- By default, most show commands (in any mode) display information for the current context only or, depending on the command syntax, for all contexts. If you are an administrator for the local context, you can insert the optional context ctx-name construct, preceding the show command, to view output for the specified context without entering that context. For more information about using the context ctx-name construct, see the context command description.
- Note:
- By appending a space followed by the pipe ( | ) character at the end of a show command, you can filter the output using a set of modifier keywords and arguments. For more information, see “Modifying Output of show Commands” in Using the CLI.
For information about troubleshooting PPPoE, see the BRAS Troubleshooting Guide.
1.14.6 Examples
The following example displays summary counter information for POS port 1 in slot 1; the detailed counters are shown after this example:
[local]Redback>show port counters 1/1
Port Type 1/1 pos packets sent : 49621 bytes sent : 1091662 packets recvd : 49620 bytes recvd : 1091640 send packet rate : 0 send bit rate : 16 recv packet rate : 0 recv bit rate : 16 rate refresh interval : 60 seconds
The following example displays detailed counters for port 1 on the POS line card in slot 1:
[local]Redback>show port counters 1/1 detail
Counters for port pos 1/1 - Interval: 5d 17:58:07
PPA Port Counters
packets sent : 49628 bytes sent : 1091816
packets recvd : 49627 bytes recvd : 1091794
send packet rate : 0 send bit rate : 16
recv packet rate : 0 recv bit rate : 16
IP mcast pkts rcv : 0 IP mcast bytes rcv : 0
IP mcast pkts sent : 0 IP mcast bytes snt : 0
rate refresh interval : 60 seconds
PPA Input Counters
idc other errors : 0 crc port errors : 0
idc overrun errors : 0 idc abort errors : 0
no cct packets : 0 no cct bytes : 0
cct down pkts : 0 cct down bytes : 0
unknown encap pkts : 0 unknown encap byte : 0
unreach pkts : 0 unreach bytes : 0
media filter pkts : 0 media filter bytes : 0
PPA Output Counters
WRED drop pkts : 0 tail drop pkts : 0
adj drop pkts : 0 adj drop bytes : 0
Packet Drop Counters
not IPv4 drop pkts : 0 bad IP checksum : 0
unhandled IP optns : 0 link layer bcast : 0
bad IP length : 0
Policing Counters
conform pkts : 0 conform bytes : 0
conform drop pkts : 0 conform drop bytes : 0
exceed pkts : 0 exceed bytes : 0
exceed drop pkts : 0 exceed drop bytes : 0
Packet-Over-Sonet physical layer statistics
Active Alarms : NONE
Sonet Section
LOS : 0 LOF : 0 BIP-B1 : 0
Sonet Line
AIS : 0 RDI : 0 BIP-B2 : 158
FEBE : 111
Sonet Path
AIS : 0 RDI : 0 BIP-B3 : 0
FEBE : 0 LOP : 0
Received Sonet Overhead
F1 : 0x0 K1 : 0x0 K2 : 0x0
S1 : 0x0 C2 : 0x16
Transmitted Sonet Overhead
F1 : 0x0 K1 : 0x0 K2 : 0x0
S1 : 0x0 C2 : 0x16
The following example displays detailed counters for port 1 on the Ethernet line card in slot 5:
[local]Redback>show port counters 5/1 detail
Counters for port ethernet 5/1 - Interval: 5d 15:05:38 PPA Port Counters packets sent : 3 bytes sent : 126 packets recvd : 0 bytes recvd : 0 send packet rate : 0 send bit rate : 0 recv packet rate : 0 recv bit rate : 0 IP mcast pkts rcv : 0 IP mcast bytes rcv : 0 IP mcast pkts sent : 0 IP mcast bytes snt : 0 rate refresh interval : 60 seconds PPA Input Error Counters idc other errors : 0 crc port errors : 0 idc overrun errors : 0 idc abort errors : 0 no cct packets : 0 no cct bytes : 0 cct down pkts : 0 cct down bytes : 0 unknown encap pkts : 0 unknown encap byte : 0 unreach pkts : 0 unreach bytes : 0 media filter pkts : 0 media filter bytes : 0 PPA Output Error Counters WRED drop pkts : 0 tail drop pkts : 0 adj drop pkts : 0 adj drop bytes : 0 Packet Drop Counters not IPv4 drop pkts : 0 bad IP checksum : 0 unhandled IP optns : 0 link layer bcast : 0 bad IP length : 0 General Counters packets sent : 3 packets recvd : 0 bytes sent : 192 bytes recvd : 0 mcast pkts sent : 0 mcast pkts recvd : 0 bcast pkts sent : 3 bcast pkts recvd : 0 dropped pkts out : 0 dropped pkts in : 0 pending pkts out : 0 pending pkts in : 0 port drops out : 0 port drops in : 0 Transmit Counters jabber : 0 error pkts sent : 0 false carrier : 0 error bytes sent : 0 late collision : 0 eth 64 octets : 3 underflow : 0 eth 65-127 octs : 0 regular collision : 0 eth 128-255 octs : 0 single collision : 0 eth 256-511 octs : 0 multiple colls : 0 eth 512-1023 octs : 0 excessive colls : 0 eth 1024-1518 octs : 0 deferred : 0 eth > 1518 octs : 0 flow control : 0 Receive Counters runt frames : 0 overflows : 0 undersized frames : 0 eth 64 octets : 0 oversized frames : 0 eth 65-127 octs : 0 crc errors : 0 eth 128-255 octs : 0 alignment errors : 0 eth 256-511 octs : 0 symbol errors : 0 eth 512-1023 octs : 0 error pkts rcvd : 0 eth 1024-1518 octs : 0 error bytes rcvd : 0 eth > 1518 octs : 0 flow control : 0
The following example displays detailed counters for port 1 on the ATM line card in slot 5:
[local]Redback>show port counters 5/1 detail
Counters for port atm 3/1 - Interval: 5d 15:03:28 PPA Port Counters packets sent : 0 bytes sent : 0 packets recvd : 0 bytes recvd : 0 send packet rate : 0 send bit rate : 0 recv packet rate : 0 recv bit rate : 0 IP mcast pkts rcv : 0 IP mcast bytes rcv : 0 IP mcast pkts sent : 0 IP mcast bytes snt : 0 rate refresh interval : 60 seconds PPA Input Counters idc other errors : 0 crc port errors : 0 idc overrun errors : 0 idc abort errors : 0 no cct packets : 0 no cct bytes : 0 cct down pkts : 0 cct down bytes : 0 unknown encap pkts : 0 unknown encap byte : 0 unreach pkts : 0 unreach bytes : 0 media filter pkts : 0 media filter bytes : 0 PPA Output Counters WRED drop pkts : 0 tail drop pkts : 0 adj drop pkts : 0 adj drop bytes : 0 Packet Drop Counters not IPv4 drop pkts : 0 bad IP checksum : 0 unhandled IP optns : 0 link layer bcast : 0 bad IP length : 0 Policing Counters conform pkts : 0 conform bytes : 0 conform drop pkts : 0 conform drop bytes : 0 exceed pkts : 0 exceed bytes : 0 exceed drop pkts : 0 exceed drop bytes : 0
1.15 show port detail
For all other line cards and all media interface cards (MICs), the syntax is:
show port [slot/port] [all] detail
1.15.1 Purpose
Displays the medium access control (MAC) address and other lower-layer settings of a single port, all ports on a card, or all ports in the system.
1.15.2 Command Mode
All modes
1.15.3 Syntax Description
|
slot |
Optional. Chassis slot number of the line card or MIC for which information is displayed. |
|
port |
Required if you enter the slot argument. Port number for which counters are displayed. The range of values depends on the type of card or MIC. |
|
chan-num |
Optional. Channel number for which port information is displayed. If omitted, displays port information for all channels on the specified port. The range of values depends on the type of port. |
|
sub-chan-num |
Optional. Subchannel number on the channel for which port information is displayed. If omitted, displays port information for all subchannels in the specified channel. The range of values depends on the type of port. |
|
all |
Includes unconfigured ports in the display. |
1.15.4 Default
Displays information for configured ports in the system.
1.15.5 Usage Guidelines
Use the show port detail command to display the medium access control (MAC) address and other lower-layer settings of a single port, all ports on a card, or all ports in the system.
- Note:
- If a port is not configured, the show port detail command does not work and the system reports the error log: Port <s>/<p> is not configured.
If you do not include any arguments, the output includes all ports present or configured in the system.
Table 16 lists the output fields for the show port command (in any mode) with the detail keyword. Not all fields apply to all types of ports; the “Type” and “Slot/Port” field names are not displayed in the output.
|
Field |
Description |
|---|---|
|
Header (first line of output) | |
|
Type |
port-type or channel-type. |
|
Slot/Port |
slot/port—Slot and port numbers for this port. |
|
State |
Port status (combination of the and fields) for a line card:
|
|
Port Parameters (in alphabetical order) | |
|
Active Alarms |
|
|
Admin state |
State of the port as a result of an operator command:
|
|
APS Group Name |
Automatic Protection Switching group name. If the port is bound to an APS group, the details are displayed as follows:
|
|
ATM MTU size |
nnnnn bytes—Size of the hardware maximum transmission unit (MTU) (not configurable). |
|
ATM Payload Scramble |
Condition of scrambling for ATM port (on or off). |
|
Auto negotiation |
Two-part string for the setting and state fields. Possible values for the setting field are:
Possible values for the state field are:
The possible combinations of the setting and state fields are:
|
|
Bandwidth |
nnnnnn kbps—Speed of SONET/SDH port. nnn.nn Mbps—Effective speed of ATM port. |
|
Cable Length |
nnn—Configured length and type (short or long, depending on configured length). |
|
CCOD Mode |
State of CCOD mode port listening: on—Port listening mode is enabled. off—Port listening mode is disabled. |
|
Clock Source(1) |
State of source of the transmit clock: global-reference—system clock on the active controller card.(2) local—local clock located on the line card (onboard clock).(3) loop—receive clock derived from the incoming signal on the port. card-reference—clock source that has been specified for the line cards. |
|
Crc |
Configured value of the cyclic redundancy check for a SONET/SDH port (16 or 32). |
|
Dampening Count |
n—Number of instances this link-dampened port went down and came up within the limits set by the link-dampening command. This count is reset only when the port is removed from the configuration with the no form of the port command (in ATM OC, ATM DS-3, or port configuration mode). |
|
Description |
Configured description. |
|
Diag Monitor |
|
|
Distant Alarm Detection |
Distant alarm (RAI) detection condition (on or off) on E1 channel. |
|
Distant Alarm Generation |
Distant alarm (RAI) generation condition (on or off) on E1 channel. |
|
DSU Bandwidth(4) |
nn.nn Mbps—Bandwidth of configured data service unit (DSU). |
|
DSU Mode (4) |
digital-link—Configured vendor of DSU. |
|
DSU Scramble (4) |
DSU scramble condition (on or off). |
|
Duplex Mode |
|
|
Encapsulation |
The encapsulation for this port:
|
|
Equipment Loopback |
Configured equipment loopback:
|
|
FEAC code received |
Far end alarm condition (of the remote system):
|
|
Flow control |
Condition of flow control for Gigabit Ethernet port, any version, (on or off). |
|
Framing |
Configured framing for the port:
|
|
Idle Character |
Configured idle character (flags or marks). |
|
Keepalive |
State of keepalive timer:
|
|
Line SD BER |
10E-5 to 10E-9—Signal degrade bit error rate for SONET/SDH port. |
|
Line SF BER |
10E-3 to 10E-5—Signal fail bit error rate for SONET/SDH port. |
|
Line state |
Physical state of the line:
|
|
Link Dampening |
For Ethernet ports. Status of link dampening:
|
|
Link up delay |
nnnnn msec—Configured or default value (in milliseconds) for the delay time for down-to-up transitions. |
|
Link down delay |
nnnnn msec—Configured or default value (in milliseconds) for the delay time for up-to-down transitions. |
|
Link Distance |
For Gigabit Ethernet ports with single-mode fiber (SMF) transceivers (LX or LX10) only. Distance supported by the installed transceiver:
|
|
Loopback |
Type of loopback:
|
|
MAC address |
nn:nn:nn:nn:nn:nn—Medium access control address for this port. |
|
Media type |
Physical interface:
|
|
Mini-RJ21 Connector |
Ports n1-n2—Range of port numbers for this connector on an FE-GE line card. |
|
MTU size |
nnnn Bytes—Configured size of the MTU for the port. |
|
NAS Port Type |
|
|
Optical Transport(6) |
|
|
Over Subscription Rate |
Configured value for over subscription:
|
|
QoS Rate Maximum(7) |
QoS port-rate limiting value:(8)
|
|
Path Alarms |
CH-OC3/CH-OC12:
CH-STM1/CH-STM4:
|
|
Path Trace Length |
The maximum size that the TX path trace message can be set to. |
|
Physical Layer(9) |
|
|
PPPoE PADO Delay |
State of PADO delay:
|
|
Restart link up delay |
The configured delay before declaring a port is up after a restart of the system. |
|
Rx path-trace |
Received path trace data. |
|
Report Only Alarms |
State of alarm reporting for an ATM or POS OC port:
Alarm is reported, but the port is not shut down. |
|
Scramble |
Status of X^43 + 1 payload scrambling for a POS port (on or off). |
|
Speed |
|
|
Support Lossless Large MTU |
Status of this FE port on an FE-GE line card with regard to guaranteed lossless flow control for jumbo frames:
|
|
Temperature |
SFP Transceiver temperature |
|
Timeslot |
Time slots configured for DS-0 channels. |
|
Tx C2 byte Rx C2 byte |
Value of the C2 byte:
|
|
Tx Fault Rx Fault |
Fault status for the transmit or receive side of the SFP transceiver installed in this port:
|
|
Tx National bit Rx National bit |
Value of the national bit (bit 12 of set 1) in the E3 frame:
|
|
Tx path-trace |
Transmitted path trace data. |
|
Tx Pwr measured [dbm](10) Rx Pwr measured [dbm] |
Current receiver sensitivity and transmitter output power for the SFP transceiver installed in this port. |
|
Undampened line state |
|
|
Vcc Measured |
SFP Transceiver Vcc |
|
Wavelength (10) |
Center wavelength for the version of the SFP optical transceiver installed in this port:
For wavelength data for each type of transceiver and its versions, see Transceivers for SmartEdge and SM Family Line Cards . |
|
Yellow Alarm Detection |
Yellow alarm (RAI) detection condition (on or off) on T1(Ds-1) channel. |
|
Yellow Alarm Generation |
Yellow alarm (RAI) generation condition (on or off) on T1(DS-1) channel. |
(1) Changes to the clock source setting
will not cause LOF on the 8-port ATM OC-3c/STM-1c.
(2) This is the default card clock
source on the 8-port ATM OC-3c/STM-1c card.
(3) This is the default card clock source on previous ATM cards, except
for the 8-port OC-3c/STM-1c card.
(4) This field is not supported
on the Channelized OC-3/STM-1 (8/4-port) / OC-12/STM-4 (2/1-port)
card.
(5) At the show port all command output on the Channelized
OC-3/STM-1 (8/4-port) / OC-12/STM-4 line card.
(6) This field is only applicable for
the 10G LAN-PHY port type.
(7) Only supported in hsvc-fair mode
on the 8-port ATM OC-3c/STM-1c (atm-oc3e-8-port) line card. When executed
in vc-fair mode, an error message occurs if executed with any value
other than 150 Mbps.
(8) When Payload line-rate
(150 Mbps) is selected, the actual line-rate received is 149.76 Mbps.
(9) This field is only applicable for
the line cards that support WAN-PHY mode.
(10) Measured
or reported values meet or exceed the transceiver specifications that
are documented in Transceivers for SmartEdge and
SM Family Line Cards.
|
Field Name |
Description |
|---|---|
|
Auxiliary monitoring not implemented |
0000b |
|
APD bias voltage (16-bit value is Voltage in units of 10 mV) |
0001b |
|
Reserved |
0010b |
|
TEC current (mA) (16-bit value is Current in units of 100 uA) |
0011b |
|
Laser temperature (same encoding as module temperature) |
0100b |
|
Laser wavelength |
0101b |
|
+5V Supply voltage |
0110b |
|
+3.3V Supply voltage |
0111b |
|
+1.8V Supply voltage |
1000b |
|
-5.2V Supply voltage (absolute value encoded as primary voltage monitor) |
1001b |
|
+5V Supply current (16-bit Value is Current in 100 uA) |
1010b |
|
+3.3V Supply current (16-bit Value is Current in 100 uA) |
1101b |
|
+1.8V Supply current (16-bit Value is Current in 100 uA) |
1110b |
|
-5.2V Supply current (16-bit Value is Current in 100 uA) |
1111b |
Not all fields apply to all types of ports; in most cases this command displays only the fields that are applicable to the type of port. The Type and Slot/Port field names are not displayed in the output.
- Note:
- By default, most show commands (in any mode) display information for the current context only or, depending on the command syntax, for all contexts. If you are an administrator for the local context, you can insert the optional context ctx-name construct, preceding the show command, to view output for the specified context without entering that context. For more information about using the context ctx-name construct, see the context command description.
- Note:
- By appending a space followed by the pipe ( | ) character at the end of a show command, you can filter the output using a set of modifier keywords and arguments. For more information, see Modifying Output of show Commands in Using the CLI.
1.15.6 Examples
The following example displays detailed configuration information for port 1 on the POS line card in slot 1:
[local]Redback>show port 1/1 detail
pos 1/1 state is Down
Description :
Line state : Down
Admin state : Down
Media type : Sonet OC12 (SM)
Encapsulation : cisco-hdlc
MTU size : 4470 Bytes
Loopback : none
Framing : sonet
Speed : 622080 kbps
Scramble : ON
Crc : 32
Tx C2 byte : 0x16
Rx C2 byte : 0x16
Line SF BER : 10E-4
Line SD BER : 10E-7
Keepalive : Set (10 sec)
Active Alarms : N/A
Path Alarms : N/A
SFP / Media Type : CWDM / MM
Tx path-trace :
73757065 72636f6d 6d370000 00000000 supercomm7......
00000000 00000000 00000000 00000000 ................
00000000 00000000 00000000 00000000 ................
00000000 00000000 00000000 00000d0a ................
Rx path-trace :
00000000 00000000 00000000 00000000 ................
00000000 00000000 00000000 00000000 ................
00000000 00000000 00000000 00000000 ................
00000000 00000000 00000000 00000000 ................The following example displays detailed configuration information for port 1 on an ATM OC line card in slot 10; the port has been configured for alarm-report-only (in ATM OC configuration mode):
[local]Redback(config-atm-oc)#show port 10/1 detail
atm 10/1 state is Down
Description :
Line state : Down
Admin state : Down
Link Dampening : enabled
Link up delay : 11000
Link down delay : 2200
Restart link up delay : 400
Undampened line state : Down
Dampening Count : 0
Media type : Sonet OC12 (SM)
Encapsulation : atm
NAS Port Type :
Loopback : none
Framing : sonet
Speed : 622.08 Mbps
Bandwidth : 599.04 Mbps
Tx C2 byte : 0x13
Rx C2 byte : 0x13
Line SF BER : 10E-4
Line SD BER : 10E-7
ATM MTU size : 65527 Bytes
MTU size : 4470 Bytes
ATM Payload Scramble : ON
Over Subscription Rate : Unlimited
MAC address : 00:30:88:01:08:18
Clock Source : card-reference
CCOD Mode : default
Report Only Alarms
Path Alarms (report only): Payload label mismatch (PLM)
Path un-equipped (UNEQ-P)
Active Alarms : N/A
Path Alarms : N/A
Path Trace Length : 64 (62 + 2 framing)
Tx Path Trace :
52656462 61636b00 00000000 00000000 Redback.........
00000000 00000000 00000000 00000000 ................
00000000 00000000 00000000 00000000 ................
00000000 00000000 00000000 00000d0a ................
Rx Path Trace :
00000000 00000000 00000000 00000000 ................
00000000 00000000 00000000 00000000 ................
00000000 00000000 00000000 00000000 ................
00000000 00000000 00000000 00000000 ................
The following example displays detailed configuration information for port 1 on the ATM line card in slot 3:
[local]Redback>show port 3/1 detail atm 3/1 state is Up Description : ATM port for Multiprotocol circuits Line state : Up Admin state : Up Media type : ds3 Encapsulation : atm ATM MTU size : 65527 Bytes MTU size : 5000 Bytes Loopback : none Framing : c-bit Framing Mode : ADM Speed : 44.736 Mbps Bandwidth : 44.21 Mbps Clock Source : global-reference Equipment Loopback : network Cable Length : 349 feet (short) ATM Payload Scramble : ON Over Subscription Rate : Unlimited MAC address : 00:00:00:00:00:00 Active Alarms : NONE FEAC code received : NONE
The following example displays detailed configuration information for port 2 on the low-density Gigabit Ethernet line card in slot 9 with a copper GBIC installed; ports 2 and 4 are unavailable with the current entitlement:
[local]Redback>show port 9/2 detail ethernet 9/2 state is Down Description : Line state :Down not entitled Admin state :Up Encapsulation :ethernet MTU size :1500 Bytes Speed :1000 Mbits/sec Duplex mode :full MAC address :00:30:88:00:13:1b Media type :1000Base-TX Flow control :on Loopback :off
The following example displays detailed configuration information for port 1 on the ATM OC-3c/STM-1c line card in slot 6:
[local]Redback>show port 6/1 detail atm 6/1 state is Up Description : ATM port for Multiprotocol circuits Line state : Up Admin state : Up Media type : Sonet OC3 (SM) Encapsulation : atm Loopback : none Framing : sonet Speed : 155.52 Mbps Bandwidth : 149.76 Mbps Qos Rate Maximum : 50 Mbps Tx C2 byte : 0x13 Rx C2 byte : 0x1 Line SF BER : 10E-5 Line SD BER : 10E-8 ATM MTU size : 65519 Bytes MTU size : 5000 Bytes ATM Payload Scramble : ON Over Subscription Rate : Unlimited MAC address : 00:00:00:00:00:00 Active Alarms : NONE
The bandwidth for an ATM OC port is the port speed minus the framing overhead. It represents the effective speed for user traffic.
The following example displays detailed configuration information, including the auto-negotiation setting being disabled and the state for Ethernet port 1 in slot 5:
ethernet 5/1 state is Down Description : Line state : Down Admin state : Down Link Dampening : enabled Link up delay : 11000 Link down delay : 2200 Restart link up delay : 400 Undampened line state : Down Dampening Count : 0 Encapsulation : ethernet MTU size : 1500 Bytes NAS Port Type : PPPoE pado delay : Set(2 sec) Speed : 1 Gbps Duplex mode : full MAC address : 00:30:88:01:64:b5 Media type : 1000Base-LX Flow control :rx state: real time state Auto-negotiation : off state: n/a Link Distance : N/A Loopback : off Wavelength : 1310.00 nm Diag Monitor : Yes TX Fault : LOW-PWR-ALARM RX Fault : LOS-Fault TX Pwr measured[dbm] : -40.00 RX Pwr measured[dbm] : -40.00
The following example displays detailed configuration information for port 1 on the ATM line card in slot 3 when auto-negotiation is enabled:
[local]Redback>show port 3/1 detail atm 3/1 state is Up Description : ATM port for Multiprotocol circuits Line state : Up Admin state : Up Media type : Sonet OC3 (SM) Encapsulation : atm Auto-negotiation : on state: unknown Flc negotiated set : tx-rx-or-rx-only state: real time state force : disabled state: inactive Flow-control : tx&rx state: n/a
The following example displays detailed port information for port 1 on a atm-oc3e-8-port line card in slot 14:
[local]Redback>show port 1/1 detail
atm 14/1 state is Up
Description :
Line state : Up
Admin state : Up
Link Dampening : enabled
Link up delay : 11000
Link down delay : 2200
Restart link up delay : 400
Undampened line state : Up
Dampening Count : 0
Media type : Sonet OC3
Encapsulation : atm
NAS Port Type :
Loopback : none
Framing : sonet
Speed : 155.52 Mbps
Bandwidth : 149.76 Mbps
Qos Rate Maximum : Line-Rate
Tx C2 byte : 0x13
Rx C2 byte : 0x13
Line SF BER : 10E-4
Line SD BER : 10E-7
ATM MTU size : 65527 Bytes
MTU size : 4470 Bytes
ATM Payload Scramble : ON
Over Subscription Rate : Unlimited
MAC address : 00:d0:b6:ff:5b:5d
Clock Source : card-reference
CCOD Mode : default
SFP Transceiver Status
Wavelength : 1310.00 nm
Diag Monitor : Yes
Tx Fault : No Fault
Rx Fault : No Fault
Tx Pwr measured[dbm] : -11.51
Rx Pwr measured[dbm] : -10.77
Temperature : 39 C
Vcc Measured : 3.23 V
APS Group Name : N/A
Report Only Alarms
Path Alarms (report only): NONE
Active Alarms : NONE
Path Alarms : NONE
Path Trace Length : 64 (62 + 2 framing)
Tx Path Trace :
6c616479 62756700 00000000 00000000 ladybug.........
00000000 00000000 00000000 00000000 ................
00000000 00000000 00000000 00000000 ................
00000000 00000000 00000000 00000000 ................
Rx Path Trace :
00000000 00000000 00000000 00000000 ................
00000d0a 526f7574 65725465 73746572 ....RouterTester
2e20506f 72742031 30332f31 2e000000 . Port 103/1....
00000000 00000000 00000000 00000000 ................The following example displays detailed port information for port 2 on a ge4-20-port line card in slot 2:
[local]Redback>show port 2/2 detail ethernet 2/2 state is Up Description : Line state : Up Admin state : Up Link Dampening : enabled Link up delay : 11000 Link down delay : 2200 Restart link up delay : 400 Undampened line state : Up Dampening Count : 0 Encapsulation : ethernet MTU size : 1500 Bytes NAS Port Type : MAC address : 00:30:88:03:ae:6f Media type : 1000Base-SX Auto-negotiation : on state: success Duplex negotiated set : full state: full Flc negotiated set : tx&rx-or-rx-only state: rx force : disabled state: inactive Speed negotiated set : 1 Gbps state: 1 Gbps Flow control : rx state: n/a Speed : 1 Gbps state: n/a Duplex mode : full state: n/a Link Distance : N/A Loopback : off SFP Transceiver Status Wavelength : 850.00 nm Diag Monitor : Yes Tx Fault : No Fault Rx Fault : No Fault Tx Pwr measured[dbm] : -4.58 Rx Pwr measured[dbm] : -3.76 Temperature : 30 C Vcc Measured : 3.15 V Active Alarms : NONE
|
The following example shows Ethernet LAN-PHY: [local]Redback#show port 11/1 detail ethernet 11/1 state is No card Description : Line state : No card Admin state : Up Link Dampening : disabled Undampened line state : No card Dampening Count : 0 Encapsulation : ethernet MTU size : 1500 Bytes NAS Port Type : NAS-Port-Id : Optical Transport : None Physical layer : lan-phy Media type : Unknown Flow control : on Clock-Source : local Link Distance : N/A Loopback : off Active Alarms : NONE |
|
The following example shows Ethernet WAN-PHY: [local]Redback#show port 11/1 detail
ethernet 11/1 state is No card
Description :
Line state : No card
Admin state : Up
Link Dampening : disabled
Undampened line state : No card
Dampening Count : 0
Encapsulation : ethernet
MTU size : 1500 Bytes
NAS Port Type :
NAS-Port-Id :
Physical layer : wan-phy
Media type : Unknown
Flow control : on
Clock-Source : local
Link Distance : N/A
Loopback : none
Framing : sonet
Line SF BER : 10E-4
Line SD BER : 10E-7
Active Alarms : NONE
Path Alarms : NONE
Tx path-trace :
52656462 61636b00 00000000 00000000 Redback.........
Rx path-trace :
00000000 00000000 00000000 00000000 ................
|
1.16 show port perf-monitor
For WAN-PHY ports, the syntax is:
show port perf-monitor slot/port [detail] [far | near]
For all other line cards and all media interface cards (MICs), the syntax is:
show port perf-monitor slot/port
1.16.1 Purpose
Displays configuration information and performance-monitoring (PM) statistics for the specified port and optionally specified channel:subchannel.
1.16.2 Command Mode
All modes
1.16.3 Syntax Description
|
slot |
Chassis slot number of the line card for which configuration information and PM statistics are displayed. |
|
port |
Port number for which configuration information and PM statistics are displayed. |
|
chan-num |
Channel number for which configuration information and PM statistics are displayed. If omitted, displays configuration information and PM statistics for all channels on the specified port. The range of values depends on the type of port. If sub-chan-num is not specified, the PM statistics are displayed for the channel specified by chan-num, and not for the individual subchannels; if sub-chan-num is specified, then the PM statistics are displayed for that channel only. |
|
sub-chan-num |
Subchannel number on the channel for which configuration information and PM statistics are displayed. If omitted, displays PM statistics for all subchannels in the specified channel. The range of values depends on the type of port. |
|
detail |
Displays detailed PM information. |
|
far |
Displays far end PM information. |
|
near |
Displays near end PM information; this setting is the default if neither the near nor far keyword is specified. |
1.16.4 Default
If no optional arguments or keywords are specified, data is for the near end.
1.16.5 Usage Guidelines
Table 18 lists the statistical data fields that are displayed with this command.
- Not all output fields described in the table are displayed for all types of ports. If you specify the detail keyword, the same statistical data fields are displayed, but with the description instead of the abbreviation.
- For definitions of the output status fields, see the show port detail command.
- If you have not enabled the Synchronous Optical Network (SONET) path trace and monitoring features for a first-generation ATM OC line card with the sonet eu command (in card configuration mode), path data is not displayed; it is not necessary to enter the sonet eu command for a second-generation ATM OC line card line card. To determine if a card has SONET path trace and monitoring features enabled, enter the show chassis command (in any mode), and check for the N flag in the Flags column.
- Some test equipment can generate time-division multiplexing (TDM) code errors such that an E3 port interprets them as a mix of excessive zeros (EXZ) and bipolar violation (BPV) errors, which usually occur in pairs; however, the E3 port considers them a single LCV error as does most legacy equipment.
- Data is displayed in 15-minute intervals; data for the current interval reflects the elapsed time in the interval. The same data is displayed in both the standard and detailed formats. If you do not specify the detail keyword, the data is shown in tabular format with the abbreviated field names; with the detail keyword, it is present in text format with the field descriptions.
- The SmartEdge 100 router limits
the value of the slot argument to 2.
The value for the port argument on the SmartEdge 100 router depends on the MIC slot in which the ATM OC MIC is installed.
- Note:
- By appending a space followed by the pipe ( | ) character at the end of a show command, you can filter the output using a set of modifier keywords and arguments. For more information, see Modifying Output of show Commands in Using the CLI.
|
Field |
Description |
|---|---|
|
BES |
Burst errored seconds |
|
CCV |
C-bit coding violations |
|
CES |
C-bit errored seconds |
|
CSES |
C-bit severely errored seconds |
|
CSS |
Controlled slip seconds |
|
DM |
Degraded minutes |
|
ES |
Errored seconds |
|
LCDS |
Loss of cell delineation seconds |
|
LCV |
Line code violations |
|
LES |
Line errored seconds |
|
LSES |
Line severely errored seconds |
|
LUAS |
Line unavailable seconds |
|
PCV |
P-bit coding violations Path code violations |
|
PES |
P-bit errored seconds Path errored seconds |
|
PLCP SEFS |
Physical layer convergence protocol (PLCP) severely errored framing seconds |
|
PLCP UAS |
PLCP unavailable seconds |
|
PSES |
P-bit severely errored seconds Path severely errored seconds |
|
PUAS |
Path unavailable seconds |
|
SCV |
Section code violations |
|
SES |
Section errored seconds |
|
SEFS |
Severely errored framing seconds |
|
SES |
Severely errored seconds |
|
SSES |
Section severely errored seconds |
|
SSEFS |
Section severely errored framing seconds |
|
UAS |
Unavailable seconds |
1.16.6 Examples
1.16.6.1 WAN-PHY Port Example
The performance monitoring of a WAN-PHY port is shown:
[local]callisto#show port perf-monitor 14/1
ethernet 14/1 state is Up
Description :
Line state : Up
Admin state : Up
Link Dampening : disabled
Undampened line state : Up
Dampening Count : 0
Encapsulation : ethernet
MTU size : 1500 Bytes
NAS Port Type :
NAS-Port-Id :
MAC address : 00:30:88:15:b3:89
Physical layer : wan-phy
Media type : 10000Base-LW
Flow control : on
Speed : 10 Gbps
Duplex mode : full
Clock-Source : local
Link Distance : 10000 meters
Loopback : none
Framing : sonet
Line SF BER : 10E-4
Line SD BER : 10E-7
XFP Transceiver Status
Wavelength : 1310.00 nm
Diag Monitor : Yes
Tx Fault : No Fault
Rx Fault : No Fault
Tx Pwr measured[dbm] : -2.03
Rx Pwr measured[dbm] : -4.13
Temperature : 30 C
Active Alarms : NONE
Path Alarms : NONE
Tx path-trace :
63616c6c 6973746f 00000000 00000000 callisto........
Rx path-trace :
506f7274 20746572 54657374 65722e00 Port terTester..
Path and Line Data
INTERVAL PCV PSES PES LCV LSES LES
759 0 0 0 0 0 0
14:45-15:00 0 0 0 0 0 0
14:30-14:45 0 0 0 0 0 0
14:15-14:30 33 0 1 2307 0 1
Total 33 0 1 2307 0 1
24 Hours 33 0 1 2307 0 1
Section Data
INTERVAL SCV SSES SSEFS SES
759 0 0 0 0
14:45-15:00 0 0 0 0
14:30-14:45 0 0 0 0
14:15-14:30 21 0 0 1
Total 21 0 0 1
24 Hours 21 0 0 1
1.16.6.2 ATM Port Example
The following example displays the configuration information and PM statistics for port 1 on the ATM line card in slot 3:
[local]Redback>show port perf-monitor 3/1
atm 3/1 state is Up
Description :
Line state : Up
Admin state : Up
Media type : ds3
Encapsulation : atm
ATM MTU size : 65527 Bytes
MTU size : 4470 Bytes
Loopback : none
Framing : c-bit
Framing Mode : ADM
Speed : 44.736 Mbps
Bandwidth : 44.21 Mbps
Clock Source : global-reference
Equipment Loopback : customer
Cable Length : 349 feet (short)
ATM Payload Scramble : ON
Over Subscription Rate : Unlimited
MAC address : 00:30:88:12:05:01
Active Alarms : NONE
FEAC code received : NONE
ATMDS3 PM DATA DISPLAY
INTERVAL LCV PCV CCV PES PSES SEFS UAS LES CES CSES
348 0 0 0 0 0 0 0 0 0 0
Total 0 0 0 0 0 0 0 0 0 0
24 Hours 0 0 0 0 0 0 0 0 0 0
PLCP PLCP
INTERVAL SEFS UAS LCDS
348 0 0 0
Total 0 0 0
24 Hours 0 0 0
1.16.6.3 ATM OC-3 Port Example
The following example displays the configuration information and PM statistics for port 1 on the 4-port ATM OC-3/STM-1c line card in slot 11:
[local]Redback>show port perf-monitor 11/1
atm 11/1 state is Up
Description :
Line state : Up
Admin state : Up
Media type : Sonet OC3 (SM)
Encapsulation : atm
Loopback : none
Framing : sonet
Speed : 155.52 Mbps
Bandwidth : 149.76 Mbps
Qos Rate Maximum : 50 Mbps
Tx C2 byte : 0x13
Rx C2 byte : 0x13
Line SF BER : 10E-4
Line SD BER : 10E-7
ATM MTU size : 65527 Bytes
MTU size : 4470 Bytes
ATM Payload Scramble : ON
Over Subscription Rate : Unlimited
MAC address : 00:30:88:00:3f:08
Clock Source : global-reference
Active Alarms : NONE
Path Alarms : NONE
Path Trace Length : 64 (62 + 2 framing)
Tx Path Trace :
6b696d62 65726c79 00000000 00000000 kimberly........
00000000 00000000 00000000 00000000 ................
00000000 00000000 00000000 00000000 ................
00000000 00000000 00000000 00000d0a ................
Rx Path Trace :
6b696d62 65726c79 00000000 00000000 kimberly........
00000000 00000000 00000000 00000000 ................
00000000 00000000 00000000 00000000 ................
00000000 00000000 00000000 00000d0a ................
Path and Line Data
INTERVAL PCV PSES PUAS PES LCDS LCV LSES LUAS LES
147 0 1 0 1 1 0 1 0 1
Total 0 1 0 1 1 0 1 0 1
24 Hours 0 1 0 1 1 0 1 0 1
Section Data
INTERVAL SCV SSES SSEFS SES
147 0 1 1 1
Total 0 1 1 1
24 Hours 0 1 1 1
1.17 show port pseudowire
show port pseudowire [pw-name [counters | detail]]
1.17.1 Command Mode
All
1.17.2 Syntax Description
|
pw-name |
Optional. Port pseudowire (PW) name. Limits the output to a specified port PW. |
|
counters |
Optional. Output includes port PW traffic counters. |
|
detail |
Optional. Detailed port PW information is displayed, such as the circuit handle, operational status, line state, administrative state, encapsulation type, MTU size, and MAC address. |
1.17.3 Default
None
1.17.4 Usage Guidelines
Use the show port pseudowire command to display the circuit handle and status for the port PWs on the router. Add the pw-name argument to display information about a specified port PW. You can add the counters keyword or the detail keyword with or without the pw-name argument to display port PW traffic counters or detailed information about the port PW.
1.17.5 Examples
The following example displays the circuit handle and state of the port PWs configured on a router:
[local]Redback#show port pseudowire Name CCT State cp1_cs1001 255/25:1:1/1/0/18 Up l2-net 255/25:1:2/1/0/22 Up
The following example displays traffic counters for the cp1_cs1001 port PW:
[local]Redback#show port pseudowire cp1_cs1001 counters
Name Packets/Bytes Sent Packets/Bytes Received
cp1_cs1001 0 0
0 0
The following example displays detailed information about the cp1_cs1001 port PW:
[local]Redback#show port pseudowire cp1_cs1001 detail cp1_cs1001 255/25:1:1/1/0/18 state is Up Description : This PW port connects through VPN 1001 Line state : Up Admin state : Up Encapsulation : ethernet MTU size : 1500 Bytes MAC address : 00:30:88:04:17:29
1.18 show port transceiver
show port slot/port[:ch[:sub]] transceiver
1.18.1 Purpose
Displays detailed information about the transceivers installed in the SmartEdge router, including their current status.
1.18.2 Command Mode
All modes
1.18.3 Syntax Description
|
slot |
Chassis slot number of the line card for which transceiver status is displayed. |
|
port |
Port number for which counters are displayed. The range of values depends on the type of card or MIC. |
|
ch |
Not Applicable. The channel number argument does not apply to this command. |
|
sub |
Not Applicable. The subchannel number argument does not apply to this command. |
|
transceiver |
Displays transceiver information. |
1.18.4 Default
Displays a list of transceivers ports that are present or configured in the system.
1.18.5 Usage Guidelines
Use the show port transceiver command to display detailed information about the transceivers installed in the router, including their current status.
Table 19 describes the values for the State field that can be displayed for a given SFP or XFP transceiver port on a SmartEdge 400, 600, 800, 1200, 1200H router.
|
State |
Description |
|---|---|
|
SFP / Media type |
SFP Transceivers—Ethernet line cards:
|
|
SFP transceivers—SONET OC-n (OC-3c/STM-1c, OC-12c/STM-4c, and OC-48c/STM-16c) cards:
| |
|
XFP / Media type |
10-Gbps SFP (XFP) transceivers—OC-192 and 10-Gig Ethernet line cards:
|
|
Ericsson Approved |
State of transceiver testing for transceiver in SmartEdge routers:
|
|
Diagnostic monitoring |
Whether the installed transceiver supports diagnostic monitoring compliant to SFF-8472 for SFPs or INF-8077i for XFPs. |
|
CLEI code |
Common Language Equipment Identifier (CLEI) code for this transceiver; blank if not applicable for this transceiver. |
|
Serial number |
nnnnnnnnnnnnnn—Unique identifier for this transceiver. |
|
Wavelength |
Center wavelength for the version of the optical transceiver installed in this port:
|
|
Additional Features |
|
|
Power Level |
|
|
Tx Pwr [dbm] |
Transmitter optical output power (measured, minimum, and maximum limits) for the version of the transceiver installed in this port. |
|
Rx Pwr [dbm] |
Receiver sensitivity (measured, minimum, and maximum limits) for the version of the transceiver installed in this port. |
|
Temperature [C] |
Temperature (measured, minimum, and maximum limits) in degrees Centigrade. |
|
Laser bias current |
Magnitude of the laser bias power setting current (measured, minimum and maximum limits), in milliamperes (mA). The laser bias provides direct modulation of laser diodes and allows the user to monitor the “health” of the laser. |
|
Vcc [V] |
Magnitude of the supply voltage to the transceiver (measured, minimum, and maximum limits), in Volts (V). |
|
AUX1(3) (for XFP transceivers only) |
Auxiliary measurement 1 for XFP transceivers—defined in Byte 222 Page 01h in INF-8077i. |
|
AUX2 (3) (for XFP transceivers only) |
Auxiliary measurement 2 for XFP transceivers—defined in Byte 222 Page 01h in INF-8077i. |
|
Active alarms(4) |
Transceiver alarm conditions for specified port/slot:
|
(1) Use part number XFP-OC192-LR2 when ordering the XFP transceivers
with 10GE ZR functionality.
(2) In Releases 6.1.4 and
6.1.5, DWDM XFP transceivers support only ITU channels 35,36,37,53,and
55.
(3) See Table 17 for a list of auxiliary input types monitored by each auxiliary
A/D channel of the XFP transceivers.
(4) The Transceiver alarms will only be
indicated here if “[no] system alarm transceiver suppress”
has been configured.
Table 20 lists describes which quantities are monitored by each auxiliary A/D channel.
|
Description of Physical Device |
Value |
|---|---|
|
Auxiliary monitoring not implemented |
0000b |
|
APD bias voltage (16-bit value is Voltage in units of 10 mV) |
0001b |
|
Reserved |
0010b |
|
TEC current (mA) (16-bit value is Current in units of 100 uA) |
0011b |
|
Laser temperature (same encoding as module temperature) |
0100b |
|
Laser wavelength |
0101b |
|
+5V Supply voltage |
0110b |
|
+3.3V Supply voltage |
0111b |
|
+1.8V Supply voltage |
1000b |
|
-5.2V Supply voltage (absolute value encoded as primary voltage monitor) |
1001b |
|
+5V Supply current (16-bit Value is Current in 100 uA) |
1010b |
|
+3.3V Supply current (16-bit Value is Current in 100 uA) |
1101b |
|
+1.8V Supply current (16-bit Value is Current in 100 uA) |
1110b |
|
-5.2V Supply current (16-bit Value is Current in 100 uA) |
1111b |
1.18.6 Examples
Example 1:
The following example displays the data and status for an SFP transceiver. The asterisk beside -13.01* in the Rx Pwr row indicates that the measured value is out of bounds of the Receive Power threshold and has caused a Transceiver Receive Power Low Alarm.:
[local]Redback#show port 11/3 transceiver
SFP / Media Type : SX / MM
Redback Approved : YES
Diagnostic Monitoring : YES
CLEI code : VAUIAAWEAA
Serial Number : F72247020031
Wavelength : 850.00 [nm]
High High Low Low
Measured Alarm Warning Alarm Warning
------------------------------------------------------------------------------------
Tx Pwr [dbm] -3.55 -1.00 -2.00 -9.50 -9.00
Rx Pwr [dbm] -40.00 0.00 -1.00 -13.01* -12.00
Temperature[C] 33 95 90 -5 0
Laser Bias Current [mA] 7.61 16.00 15.00 2.00 3.00
Vcc [V] 3.26 3.63 3.58 2.97 3.02
Active Alarms : Link down
Transceiver Receive Power Low Alarm
Example 2:
The following example displays the data and status for an XFP transceiver:
[local]Redback#show port 11/3 transceiver
XFP / Media Type : LR / SM
Redback Approved : NO
Diagnostic Monitoring : YES
CLEI code : IPUIANWCAA
Serial Number : UDE03CT
Wavelength : 1307.00[nm]
High High Low Low
Measured Alarm Warning Alarm Warning
------------------------------------------------------------------------------------
Tx Pwr [dbm] -1.98 1.50 1.00 -7.00 -6.00
Rx Pwr [dbm] -40.00 2.50 2.00 -20.00 -18.01
Temperature[C] 19 83 80 -13 -10
Laser Bias Current [mA] 35.00 80.00 75.00 15.00 20.00
AUX1 +3.3V Supply Voltage 3.31 3.63 3.50 3.00 3.10
AUX2 N/A N/A N/A N/A N/A N/A
Active Alarms : Link down
1.19 show ppp
For ports on Packet over SONET/SDH (POS) line cards, the syntax is:
show ppp [slot/port] [starting | up | down] [summary | detail] [all]
1.19.1 Purpose
Displays the states of one or more Point-to-Point Protocol (PPP) sessions.
1.19.2 Command Mode
All modes
1.19.3 Syntax Description
|
slot |
Optional. Chassis slot number of the line card for which PPP session information displays. Use the slot, port, chan-num, and sub-chan-num arguments to display information only for the PPP sessions on that slot, port, channel, or subchannel. |
|
port |
Required if you enter the slot argument. Port number for which PPP sessions are displayed. If not specified, sessions are displayed for all ports in the specified slot. |
|
chan-num |
Optional. Channel number for which PPP session information displays. If omitted, displays PPP session information for all channels on the specified port. The range of values depends on the type of port. |
|
sub-chan-num |
Optional. Subchannel number for which PPP session information displays. If omitted, displays PPP session information for all subchannels in the specified channel. The range of values depends on the type of port. |
|
starting |
Optional. Specifies that only starting PPP sessions are to be displayed. |
|
up |
Optional. Specifies that only PPP sessions for which the Link Control Protocol (LCP) and IP Control Protocol (IPCP) are in the OPENED state are to be displayed. |
|
down |
Optional. Specifies that only PPP sessions for which the LCP is in the INITIAL, CLOSED, or STOPPED state are to be displayed. |
|
summary |
Optional. Displays summary information for all PPP sessions. |
|
detail |
Optional. Specifies that context and Multilink PPP (MLPPP) bundle information is to be displayed. |
|
all |
Optional. Specifies that PPP session information in all contexts is shown. This option is available only in the local context. Use the all keyword in the local context to display information for all PPP sessions in all contexts. In all other contexts, only PPP sessions bound to the current context are shown. |
1.19.4 Default
Displays information for all PPP sessions in the current context.
1.19.5 Usage Guidelines
Use the show ppp command to display the states of one or more PPP sessions. For information about troubleshooting PPP, see the BRAS Troubleshooting Guide.
- Note:
- The SmartEdge 100 router limits the value of the slot argument to 2.
- Note:
-
The value for the port argument on the SmartEdge 100 router is one of the following:
- For a native port, it is 1 or 2.
- For a MIC port, it depends on the MIC and MIC slot in which it is installed.
- Note:
- The value for the port argument on the SmartEdge 100 router depends on the MIC slot in which the ATM OC MIC is installed.
Table 21 lists the output fields for the show ppp command with the detail keyword.
|
Field |
Description |
|---|---|
|
Port/Circuit |
Slot, port, channel, subchannel, and circuit identifiers |
|
Unit |
Internal identifier |
|
LCP State |
Protocol state on this circuit, as defined in RFC 1661, The Point-to-Point Protocol (PPP) |
|
IPCP State |
Protocol state on this circuit, as defined in RFC 1661 |
|
NLCP State |
Protocol state on this circuit, as defined in RFC 1661 |
|
MPLSCP State |
Protocol state on this circuit, as defined in RFC 1661 |
|
Initial Context |
Context in which the interface exists for this PPP encapsulated circuit |
- Note:
- By default, most show commands (in any mode) display information for the current context only or, depending on the command syntax, for all contexts. If you are an administrator for the local context, you can insert the optional context ctx-name construct, preceding the show command, to view output for the specified context without entering that context. For more information about using the context ctx-name construct, see the context command description.
- Note:
- By appending a space followed by the pipe ( | ) character at the end of a show command, you can filter the output using a set of modifier keywords and arguments. For more information, see Modifying Output of show Commands in Using the CLI.
1.19.6 Examples
1.19.6.1 Summary
The following example shows how to display summary output for PPP sessions in the current context:
[local]Redback>show ppp summary
Wed Jun 30 21:54:29 2005
Number LCP IPCP NLCP MPLSCP
Circuit Type Circuit Open Open Open Open
------------ ------- ---- ---- ---- ------
mp circuits 2 2 2 0 0
ppp circuits 2 2 2 0 0
Total circuits: 4 up: 4 down: 0
1.19.6.2 <Sessio-ID> Up Detail
The following example shows how to display detailed information for PPP sessions that are up for all ports on the line card in slot 11:
[local]Redback>show ppp 11 up detail
Wed Jun 30 16:59:38 2005
LCP IPCP NLCP MPLSCP
Port/Circuit Unit State State State State
------------------------------------ ----- -------- -------- -------- --------
11/1:1 2 Opened Opened Initial
Initial Context: local
11/2:1 3 Opened Opened Initial
Initial Context: remote
1.19.6.3 All
The following example displays output for all PPP sessions in all contexts:
[local]Redback>show ppp all
Sat Aug 22 20:14:06 2009
LCP IPCP IPV6CP NLCP MPLSCP
Port/Circuit Unit State State State State State
----------------------------- ----- -------- -------- -------- --------
--------
5/7:1:2:1 0 Opened -ML- -ML- -ML-
5/7:1:2:2 4 Opened -ML- -ML- -ML-
5/8:1:2:1 5 Opened -ML- -ML- -ML-
5/8:1:2:2 1 Opened -ML- -ML- -ML-
bundle_1 2 N/A Opened Initial Initial
bundle_2 3 N/A Opened Initial Initial
Total circuits: 4 up: 4 down: 0
1.20 show ppp counters
show ppp counters [all-contexts | context | detail | summary]
1.20.1 Purpose
Displays statistics for Point-to-Point Protocol (PPP) packets and session counters on the system.
1.20.2 Command Mode
All modes
1.20.3 Syntax Description
|
all-contexts |
Optional. Displays context-specific PPP counters for all contexts. This keyword is available only for administrators authenticated to the local context. |
|
context |
Optional. Displays context-specific PPP counters for the current context. |
|
detail |
Optional. Displays detailed information for global PPP counters. |
|
summary |
Optional. Displays totals for context-specific PPP counters across all contexts. This keyword is available only for administrators authenticated to the local context. The summary keyword adds together the context-specific PPP counters from all contexts. |
1.20.4 Default
If no keyword is specified, the global PPP counters are displayed.
1.20.5 Usage Guidelines
Use the show ppp counters command to display statistics for PPP packets and session counters on the system.
- Note:
- By default, most show commands (in any mode) display information for the current context only or, depending on the command syntax, for all contexts. If you are an administrator for the local context, you can insert the optional context ctx-name construct, preceding the show command, to view output for the specified context without entering that context. For more information about using the context ctx-name construct, see the context command description.
- Note:
- By appending a space followed by the pipe ( | ) character at the end of a show command, you can filter the output using a set of modifier keywords and arguments. For more information, see Modifying Output of show Commands in Using the CLI. For information about troubleshooting PPP, see the BRAS Troubleshooting Guide.
1.20.6 Examples
1.20.6.1 Current Context
The following example shows how to display the context-specific PPP counters for the current context:
[local]Redback>show ppp counters context
Last cleared: Never
received: bytes 260, packets 26,
unsupported packets 0
sent: bytes 260, packets 26
LCP echo request : received 26, sent 0, dropped 0
LCP echo response : received 0, sent 26, dropped 0
LCP protocol reject : received 0, sent 0, dropped 0
1.20.6.2 Global Counters
The following example shows how to display global PPP counters:
[local]Redback>show ppp counters Wed Jun 30 21:56:07 2005 Packet-------------------------------------------------------- In 285 Out 287 Session------------------------------------------------------- LCP Up 72 LCP Down 68 IPCP Up 12 IPCP Down 6 Authen Success 0 Authen Failure 0 Session Up 0 Session Down 0 SessionControl------------------------------------------------ Starting 0 Authenticating 0 Pended (current) 0 Pended (total) 0 Packet Drop Session pended 0 At Limit 0 Timeout------------------------------------------------------- ConfReq 85 TermReq 19 CHAP Challenge 0 UPAP Listen 0 PacketDropIn-------------------------------------------------- Session is Down 17 Bad FSM State 32
1.20.6.3 Counters Detail
The following example shows how to display detailed information for global PPP counters:
[local]Redback>show ppp counters detail Packet-------------------------------------------------------- In 40 Out 40 ConfReq 24 ConfReq 10 ConfAck 10 ConfAck 10 ConfNak 0 ConfNak 4 ConfRej 0 ConfRej 10 TermReq 4 TermReq 2 TermAck 2 TermAck 4 Authen Proto 6 Authen Proto 6 other 0 other 0 Session------------------------------------------------------- LCP Up 6 LCP Down 6 IPCP Up 4 IPCP Down 4 Authen Success 4 Authen Failure 2 Session Up 4 Session Down 6 SessionControl------------------------------------------------ Starting 0 Authenticating 0 Pended (current) 0 Pended (total) 0 Packet Drop Session pended 0 At Limit 0 Timeout------------------------------------------------------- ConfReq 0 TermReq 4 CHAP Challenge 0 UPAP Listen 0 PacketDropIn-------------------------------------------------- Session is Down 1 Bad FSM State 0 DownCause----------------------------------------------------- Rcvd TermReq 4 Rcvd PPPoE PADT 0 No ConfReq Resp 0 No Echo Resp 0 Authen Failed 2 Session Down 0 LCP Down 0 Circuit Down 0 Port Down 0 Port Delete 0
1.21 show ppp multilink
show ppp multilink [{all | bundle {bundle-name | mp sess-id}} [detail] | detail | summary]
1.21.1 Purpose
Displays information for Multilink Point-to-Point Protocol (MLPPP) bundles.
1.21.2 Command Mode
All modes
1.21.3 Syntax Description
|
all |
Optional. Displays information for all MLPPP bundles in all contexts. |
|
bundle |
Optional. Displays information for a specific MLPPP bundle. |
|
bundle-name |
Name of the MLPPP bundle of DS-1 channels, E1 channels, or E1 ports to be displayed. |
|
mp sess-id |
Session ID of the circuit in the MLPPP bundle; the range of values is 1 to 65534. |
|
detail |
Optional. Displays additional multilink information. |
|
summary |
Optional. Displays a summary of all Point-to-Point Protocol (PPP) and MLPPP sessions for all contexts. |
1.21.4 Default
When used without any optional constructs, displays information about all MLPPP bundles in the current context.
1.21.5 Usage Guidelines
Use the show ppp multilink command to display information for MLPPP bundles.
Use the bundle-name argument to specify an MLPPP bundle configured with DS-1 channels, E1 channels, or E1 ports; use the mp sess-id construct to specify an MLPPP bundle created by the system on a PPP-encapsulated or PPP over Ethernet (PPPoE)-encapsulated circuit.
To determine the session ID for an MLPPP bundle, use the show ppp all or show circuit command (in any mode).
- Note:
- By default, most show commands (in any mode) display information for the current context only or, depending on the command syntax, for all contexts. If you are an administrator for the local context, you can insert the optional context ctx-name construct, preceding the show command, to view output for the specified context without entering that context. For more information about using the context ctx-name construct, see the context command description.
- Note:
- By appending a space followed by the pipe ( | ) character at the end of a show command, you can filter the output using a set of modifier keywords and arguments. For more information, see Modifying Output of show Commands in Using the CLI. For information about troubleshooting PPP, see the BRAS Troubleshooting Guide.
1.21.6 Examples
1.21.6.1 No Keywords
The following example shows how to display information for any MLPPP bundle:
[local]Redback>show ppp multilink Bundle Name: bar Link Count: 2 Username: (null) Our MRRU: 1524 Peer MRRU: 1524 Our Endpoint-Discriminator: class-1 Redback Peer Endpoint-Discriminator: class-1 Redback Member Links Status 5/3 active 5/1 active
1.21.6.2 All
The Link Count field displays the number of links that are up.
The following example shows how to display information for all link groups in all contexts:
[local]Redback>show ppp multilink all [local]driver# show ppp multilink all Bundle Name: bundle_1 Link Count: 2 Username: Our MRRU: 3002 Peer MRRU: 2002 Our Endpoint-Discriminator: class-2 70.100.100.1 Peer Endpoint-Discriminator: class-2 70.100.100.2 Member Links Status 5/7:1:2:2 active (master) 5/7:1:2:1 active Bundle Name: bundle_2 Link Count: 2 Username: Our MRRU: 2002 Peer MRRU: 3002 Our Endpoint-Discriminator: class-2 70.100.100.2 Peer Endpoint-Discriminator: class-2 70.100.100.1 Member Links Status 5/8:1:2:2 active (master) 5/8:1:2:1 active
1.21.6.3 All Detail
[local]driver# show ppp multilink all det Bundle Name: bundle_1 MP-ID: 297 Link Count: 2 Username: Our MRRU: 3002 Peer MRRU: 2002 Our Endpoint-Discriminator: class-2 70.100.100.1 Peer Endpoint-Discriminator: class-2 70.100.100.2 Acct handle: 255/7:5:42/1/1/2 Member Links Status 5/7:1:2:2 active (master) cct handle : 5/7:1:2:2/1/1/59 5/7:1:2:1 active cct handle : 5/7:1:2:1/1/1/62 Bundle Name: bundle_2 MP-ID: 298 Link Count: 2 Username: Our MRRU: 2002 Peer MRRU: 3002 Our Endpoint-Discriminator: class-2 70.100.100.2 Peer Endpoint-Discriminator: class-2 70.100.100.1 Acct handle: 255/7:5:43/1/1/3 Member Links Status 5/8:1:2:2 active (master) cct handle : 5/8:1:2:2/1/1/52 5/8:1:2:1 active cct handle : 5/8:1:2:1/1/1/65
1.21.6.4 Summary
The following example shows how to display summary information only:
[local]Redback>show ppp multilink summary
Wed Jun 30 06:38:05 2005
NUMBER LCP IPCP NLCP
CIRCUIT TYPE CIRCUIT OPEN OPEN OPEN
------------ ------- ---- ---- ----
mp circuits 24 24 3 0
ppp circuits 0 0 0 0
Total circuits: 24 up: 24 down: 0
1.21.6.5 Bundle <bundle-name>
The following example shows how to display information for the bundle_2 MLPPP bundle:
[local]Redback>show ppp multilink bundle bundle_2 Bundle Name: bundle_2 Link Count: 2 Username: Our MRRU: 2002 Peer MRRU: 3002 Our Endpoint-Discriminator: class-2 70.100.100.2 Peer Endpoint-Discriminator: class-2 70.100.100.1 Member Links Status 5/8:1:2:2 active (master) 5/8:1:2:1 active
1.21.6.6 Bundle MLPPP Session-ID
The following example shows how to display information for an MLPPP bundle using its session ID:
[local]Redback>show ppp multilink bundle mp 297 Bundle Name: bundle_1 Link Count: 2 Username: Our MRRU: 3002 Peer MRRU: 2002 Our Endpoint-Discriminator: class-2 70.100.100.1 Peer Endpoint-Discriminator: class-2 70.100.100.2 Member Links Status 5/7:1:2:2 active (master) 5/7:1:2:1 active
1.21.6.7 Bundle <bundle-name> Detail
The following example shows how to display information about the MLPPP bundle named abc. Because the command includes the detail keyword, the output provides both the bundle handle (Acct handle) and circuit handle (cct handle) information. Note also that 6/1:1:1 under Member Links provides the port/slot:channel:subchannel of the master link:
[local]Redback>show ppp multilink bundle abc detail Bundle Name: abc Link Count: 1 Username: Our MRRU: 1500 Peer MRRU: 1500 Our Endpoint-Discriminator: class-1 dino Peer Endpoint-Discriminator: class-1 dino Acct handle: 255/7:1023:63/1/1/2 Member Links Status 6/1:1:1 active (master) cct handle : 6/1:1:1/1/1/19
1.22 show pppoe
show pppoe [down | mac | services | session sess-id | starting | subscribers slot[/port] circuit-id | summary | up] [all]
1.22.1 Purpose
Displays Point-to-Point Protocol over Ethernet (PPPoE) information for one or more subscriber circuits.
1.22.2 Command Mode
All modes
1.22.3 Syntax Description
|
down |
Optional. Displays PPPoE information for subscriber sessions that are down. |
|
mac |
Optional. Displays PPPoE information for a particular Medium Access Control (MAC) address. |
|
services |
Optional. Displays PPPoE services currently being advertised. |
|
session sess-id |
Optional. Session ID for the subscriber circuit for which PPPoE information is to be displayed; the range of values is 1 to 65535. |
|
starting |
Optional. Displays PPPoE information for subscriber sessions that are starting. |
|
subscribers |
Optional. Displays a list of subscribers according to the following arguments. |
|
slot |
Chassis slot number of a line card with the PPPoE-encapsulated circuit for which subscriber sessions are displayed. Available only if you enter the subscribers keyword. |
|
port |
Optional. Port number of the PPPoE-encapsulated circuit for which subscriber sessions are displayed. If not specified, sessions are displayed for all PPPoE-encapsulated circuits on the card in the specified slot. |
|
circuit-id |
Optional. Circuit identifier, according to one of the constructs listed in Table 22. |
|
summary |
Optional. Displays summary information for current context. |
|
up |
Optional. Displays PPPoE information for subscriber sessions that are up. |
|
all |
Optional. Displays PPPoE information for PPPoE-encapsulated subscriber circuits in all contexts. This option is only available in the local context. |
1.22.4 Default
None
1.22.5 Usage Guidelines
Use the show pppoe command to display PPPoE-related information for one or more circuits.
- Note:
- The SmartEdge 100 router limits the value of the slot argument to 2.
- Note:
- The value for the port argument on the SmartEdge 100 router is one of the following:
- For a native port, it is 1 or 2.
- For a MIC port, it depends on the MIC and MIC slot in which it is installed.
Table 22 lists the values for the circuit-id argument.
|
Construct |
Description |
|---|---|
|
vlan-id vlan-id |
Virtual LAN (VLAN) tag value for an 802.1Q tunnel or PVC. The vlan-id argument is one of the following constructs:
The range of values for any VLAN tag value is 1 to 4095. |
|
vpi-vci vpi vci |
Virtual path identifier (VPI) and virtual circuit identifier (VCI) for an Asynchronous Transfer Mode (ATM) permanent virtual circuit (PVC). The range of values is 0 to 255 and 1 to 65535, respectively. |
- Note:
- By default, most show commands (in any mode) display information for the current context only or, depending on the command syntax, for all contexts. If you are an administrator for the local context, you can insert the optional context ctx-name construct, preceding the show command, to view output for the specified context without entering that context. For more information about using the context ctx-name construct, see the context command description.
- Note:
- By appending a space followed by the pipe ( | ) character at the end of a show command, you can filter the output using a set of modifier keywords and arguments. For more information, see Modifying Output of show Commands in Using the CLI. For information about troubleshooting PPPoE, see the BRAS Troubleshooting Guide.
1.22.6 Examples
1.22.6.1 Summary
The following example shows how to display summary information:
[local]Redback>show pppoe summary
NUMBER
CIRCUIT TYPE CIRCUIT UP DOWN
------------ ------- ------ ------
ATM 3 3 0
ETHERNET 0 0 0
DOT1Q 0 0 0
Total circuits: 3 up: 3 down: 0
1.22.6.2 Services
The following example shows how to display services information:
[local]Redback>show pppoe services
Context: local
Number of domains: 2
Domain: adsl (not advertise)
Domain: redback (not advertise)
Context: one
Number of domains: 1
Domain: pppoe (not advertise)
1.22.6.3 Local Context
The following example shows how to display information for all PPPoE circuits in the local context:
[local]Redback>show pppoe Wed Jun 30 01:38:42 2005 Circuit MAC address Subscriber ---------------------------------------------------------------------- 3/1 vpi-vci 0 32 pppoe 2001 00:10:67:00:2a:01 a-32@local 3/1 vpi-vci 0 33 pppoe 2002 00:10:67:00:2a:02 a-33@local 3/1 vpi-vci 0 34 pppoe 2003 00:10:67:00:2a:03 a-34@local
1.23 show pppoe counters
show pppoe counters [detail]
1.23.1 Purpose
Displays summary or detailed statistics for all Point-to-Point Protocol (PPP) over Ethernet (PPPoE)-encapsulated circuits.
1.23.2 Command Mode
All modes
1.23.3 Syntax Description
|
detail |
Optional. Displays detailed statistics. |
1.23.4 Default
None
1.23.5 Usage Guidelines
Use the show pppoe counters command to display summary or detailed statistics for all PPPoE-encapsulated circuits.
- Note:
- By default, most show commands (in any mode) display information for the current context only or, depending on the command syntax, for all contexts. If you are an administrator for the local context, you can insert the optional context ctx-name construct, preceding the show command, to view output for the specified context without entering that context. For more information about using the context ctx-name construct, see the context command description.
- Note:
- By appending a space followed by the pipe ( | ) character at the end of a show command, you can filter the output using a set of modifier keywords and arguments. For more information, see Modifying Output of show Commands in Using the CLI. For information about troubleshooting PPPoE, see the BRAS Troubleshooting Guide.
1.23.6 Examples
The following example shows how to display summary statistics:
[local]Redback>show pppoe counters
Wed Jun 30 01:37:25 2005 PPPoE PAD counters: ------------------- sent packets : 4000 recv packets : 4000 dropped packets : 0 PADI packets : 2000 PADO packets : 2000 PADR packets : 2000 PADS packets : 2000 PADT packets : 0 PADM packets : 0 PADN packets : 0
The following example shows how to display detailed statistics:
[local]Redback>show pppoe counters detail
Wed Jun 30 08:30:40 2005 PPPoE PAD counters: ------------------- sent packets : 4000 recv packets : 4000 dropped packets : 0 PADI packets : 2000 PADO packets : 2000 PADR packets : 2000 PADS packets : 2000 PADT packets : 0 PADM packets : 0 PADN packets : 0 PPPoE invalid discovery packet counters: ---------------------------------------- invalid version/type : 0 invalid length : 0 invalid tag length : 0 unknown code : 0 PADIs non-zero sess-id : 0 PADRs non-zero sess-id : 0 PADT, bad MAC addr : 0 bad encaps : 0 PADR, max sess reached : 0 PADR, same MAC : 0 tags not added, large pkt: 0 recv on down circuit : 0 invalid tag name : 0 invalid tag name accepted: 0 circuit not created : 0 circuit not init : 0 packet on virtual circuit: 0 non subscriber circuit : 0 unknown circuit : 0 proc restart drops : 0 PPPoE virtual circuit counters: ------------------------------- created virtual circuits : 0 deleted virtual circuits : 0 combined circuits used : 4000 combined circuits reset : 2000 create failed : 0 delete failed : 0 create fail, rcct used : 0 create fail, no cct : 0 create fail, cct init : 0 create fail, vcct exists : 0 circuit lookup failures : 0 PPPoE PADM error counters: -------------------------- malformed URLs : 0 too long expanded URLs : 0 too long MOTMs : 0 bad expansion char : 0 PADX on bad circuit : 0 PPPoE session counters: ----------------------- session down cplt recv : 2000 session down cplt proc : 2000 stale entry cleanup : 0 bad state entry cleanup : 0 session down sent : 0
1.24 show privilege
show privilege
1.24.1 Purpose
Displays the current privilege level for the current exec session.
1.24.2 Command Mode
All modes
1.24.3 Syntax Description
This command has no keywords or arguments.
1.24.4 Default
None
1.24.5 Usage Guidelines
Use the show privilege command to display the current (administrator) privilege level for the current exec session.
If you are an administrator at privilege level 10 or higher, you can determine the privilege level of any given command at your level or lower by recursively entering the enable and show ? commands.
For example, if an administer at privilege level 15 enters the show privilege command, all commands at privilege level 15 and lower are listed. If the administrator then enters the enable command for privilege level 14 and the show privilege command again, all commands at privilege level 14 and lower are listed. The administrator can repeat these steps at levels 13, 12, and so on until all privilege levels are listed.
Be aware that this method lists the current privilege levels, which could be different from the default privilege levels. See the privilege command in the Command List for more information.
- Note:
- By default, most show commands (in any mode) display information for the current context only or, depending on the command syntax, for all contexts. If you are an administrator for the local context, you can insert the optional context ctx-name construct, preceding the show command, to view output for the specified context without entering that context. For more information about using the context ctx-name construct, see the context command description.
- Note:
- By appending a space followed by the pipe ( | ) character at the end of a show command, you can filter the output using a set of modifier keywords and arguments. For more information, see Modifying Output of show Commands in Using the CLI.
1.24.6 Examples
The following example displays output from the show privilege command:
[local]Redback>show privilege
Current privilege level is 6
1.25 show process
show process [proc-name] [{crash-info | detail}]
1.25.1 Purpose
Displays current status of one or all processes running on the system.
1.25.2 Command Mode
All configuration modes
1.25.3 Syntax Description
|
proc-name |
Optional. Process for which you want to display information. The value of the proc-name argument can be any one of the keywords listed in Table 23. |
|
crash-info |
Optional. Specifies that process crash information is to be monitored. |
|
detail |
Optional. Specifies that detailed process information is to be displayed. |
1.25.4 Default
When used without any optional constructs, this command displays summary status of all tasks running.
1.25.5 Usage Guidelines
Use the show process command to display current information on a specific category of processes, or on all running processes.
Table 23 lists the keywords for the processes supported by this command.
|
Keyword |
Process |
|---|---|
|
aaad |
authentication, authorization, and accounting (AAA) process |
|
arp |
Address Resolution Protocol (ARP) process |
|
atm |
Asynchronous Transfer Mode (ATM) process |
|
bgp |
Border Gateway Protocol (BGP) process |
|
bridge |
bridge process |
|
cfm |
Ethernet 802.1ag CFM process |
|
clips |
clientless IP service selection process |
|
cls |
Classifier Manager process |
|
cpustats |
Display CPU statistics |
|
csm |
Controller State Manager (CSM) process |
|
cspf |
Contstrained Shortest-Path First (CSPF) process |
|
dhcp |
Dynamic Host Configuration Protocol (DHCP) relay/proxy process |
|
dhcpv6 |
DHCPv6 daemon |
|
dhelperd |
DHCP helper daemon |
|
dhelper6 |
DHCPv6 helper daemon |
|
dlm |
Download Manager (DLM) process |
|
dns |
Domain Name System (DNS) process |
|
dot1q |
802.1Q encapsulation process(1) |
|
flowd |
flow process(2) |
|
fr |
Frame Relay process (3) |
|
fsd |
File server process |
|
fssbcsim |
FSSB Client Simulator process |
|
gsmp |
General Switch Management Protocol (GSMP) process |
|
hr |
HTTP redirect process |
|
igmp |
Internet Group Management Protocol (IGMP) process |
|
isis |
Intermediate System-to-Intermediate System (IS-IS) process |
|
ism |
Interface and Circuit State Manager (ISM) process |
|
l2tp |
Layer 2 Tunneling Protocol (L2TP) process |
|
lvl7d |
L4L7 process |
|
ldp |
Label Distribution Protocol (LDP) process |
|
lg |
link group (LG) process |
|
lm |
Label Manager (LM) process |
|
mcastmgr |
Multicast manager process |
|
metad |
Meta process |
|
mgd |
Media Gateway process |
|
mgmd |
Media Gateway Manager process |
|
mip |
Mobile IP process |
|
mipsim |
Mobile IP Simulator process |
|
mpls_static |
Multiprotocol Label Switching (MPLS) static process |
|
msdp |
Multicast Source Discovery Protocol (MSDP) process |
|
nat |
IP Network Address Translation (NAT) process |
|
nd |
neighbor discovery (ND) process |
|
netopd |
NetOp process daemon |
|
ntp |
Network Time Protocol (NTP) process |
|
odd |
on-demand diagnostics (ODD) process |
|
ospf |
Open Shortest Path First (OSPF) protocol process |
|
ospf3 |
OSPF Version 3 (OSPF3) protocol process |
|
ped_parse |
process execution descriptor (PED) parse process |
|
pem |
Port encapsulation module (PEM) process |
|
pim |
Protocol Independent Multicast (PIM) process |
|
ppaslog |
Packet Processing ASIC (PPA) syslog process |
|
ppp |
Point-to-Point Protocol (PPP) process |
|
pppoe |
PPP over Ethernet (PPPoE) process |
|
qos |
quality of service (QoS) process |
|
rcm |
Router Configuration Manager (RCM) process |
|
rib |
Routing Information Base (RIB) process |
|
rip |
Routing Information Protocol (RIP) process |
|
rpm |
Routing Policy Manager (RPM) process |
|
rsvp |
Resource Reservation Protocol Traffic Engineering (RSVP-TE) process |
|
shm_ribd |
Shared Memory RIB daemon |
|
snmp |
Simple Network Management Protocol (SNMP) process |
|
static |
static routing process |
|
stats |
statistics process |
|
sysmon |
system monitor process |
|
tunnel |
tunnel management process |
|
vrrp |
Virtual Router Redundancy Protocol (VRRP) process |
|
xcd |
cross-connect process daemon |
(1) The SmartEdge 100 router
does not support 802.1Q.
(2) Not all controller cards support flow.
(3) The SmartEdge 100 router does
not support Frame Relay.
- Note:
- By default, most show commands (in any mode) display information for the current context only or, depending on the command syntax, for all contexts. If you are an administrator for the local context, you can insert the optional context ctx-name construct, preceding the show command, to view output for the specified context without entering that context. For more information about using the context ctx-name construct, see the context command description.
- Note:
- By appending a space followed by the pipe ( | ) character at the end of a show command, you can filter the output using a set of modifier keywords and arguments. For more information, see Modifying Output of show Commandsin Using the CLI.
1.25.6 Examples
The following example displays output from the show process command. The column heading PID stands for process ID:
[local]Redback>show process
Load Average : 1.37 1.39 1.40 NAME PID SPAWN MEMORY TIME %CPU STATE UP/DOWN csm 10989 1 544K 00:02:45.10 0.00% run 02:54:18 rcm 10990 1 2008K 00:00:56.44 0.00% run 02:54:16 ism 10991 1 504K 00:01:50.71 0.00% run 02:54:15 rpm 10992 1 404K 00:00:24.31 0.00% run 02:54:15 rib 10993 1 992K 00:00:45.41 0.00% run 02:54:15 ntp 10995 1 496K 00:00:40.43 0.00% run 02:59:29 static 13035 4 444K 00:00:04.34 0.00% run 02:59:29 isis 0 0 0K Not Avail 0.00% demand 02:54:13 rip 12652 1 576K 00:00:11.01 0.00% run 02:59:29 bgp 0 0 0K Not Avail 0.00% demand 02:54:13 igmp 0 0 0K Not Avail 0.00% demand 02:54:13 ospf 11089 1 704K 00:34:31.05 0.00% run 02:59:29 sysmon 10997 1 396K 00:00:32.27 0.00% run 02:35:08 dns 10998 1 404K 00:00:24.98 0.00% run 02:35:08
The following example displays output from the show process command with the crash-info keyword:
[local]Redback>show process crash-info
ME TIME STATUS ospf Mon Jan 27 14:05:43 2001 Kill (9) ism Mon Jan 27 14:28:26 2001 Kill (9) ism Mon Jan 27 14:28:50 2001 Kill (9)
The following example displays output from the show process command with the ism detail keywords:
[local]Redback>show process ism detail
Process (PID) : ism (20536) Spawn count : 1 Memory : 708K Time : 00:00:00.16 %CPU : 0.00% State : run Up time : 02:37:15 Heart beat : Enabled Spawn time : 2 seconds Max crashes allowed : 5 Crash thresh time : 86400 seconds Total crashes : 0 Images: (Spawns, Max spawns, Version, Path) (*) 1, 3, v1, /usr/redback/bin/ism Client IPC Endpoints: EP 0100007f 060058fe - RIB-IPC-MSG-EP-NAME:00000000 EP 0100007f 060058fe - NTP-ISM-MSG-EP-NAME:00000000 Server IPC Endpoints: EP 0100007f 080058fe - ISM2-CLIENT-NETBYTE-EP-NAME:00000000 EP 0100007f 070058fe - ISM2-CLIENT-EP-NAME:00000000 EP 0100007f 060058fe - ISM-CLIENT-EP-NAME:00000000 EP 0100007f 050058fe - ISM-CONF-EP-NAME:00000000
The following example displays output from the show process command with the cpustats keyword:
[local]Redback#show process cpustats
Total system CPU % usage (5s, 1m, 5m): 0.00, 0.00, 0.00
Proc/thread name: 5sec 1min 5min Proc/thread name: 5sec 1min 5min
-----------------------------------
-----------------------------------
exec_cli: 0.00 0.00 0.00 staticd: 0.00 0.00 0.00
ndd: 0.00 0.00 0.00 clipsd: 0.00 0.00 0.00
l2tpd: 0.00 0.00 0.00 pppoed: 0.00 0.00 0.00
aaad: 0.00 0.00 0.00 pppd: 0.00 0.00 0.00
statd: 0.00 0.00 0.00 dhelperd: 0.00 0.00 0.00
oddd: 0.00 0.00 0.00 lm: 0.00 0.00 0.00
dhcpd: 0.00 0.00 0.00 pemd: 0.00 0.00 0.00
dlmd: 0.00 0.00 0.00 clsd: 0.00 0.00 0.00
ppaslogd: 0.00 0.00 0.00 sysmond: 0.00 0.00 0.00
arpd: 0.00 0.00 0.00 ribd: 0.00 0.00 0.00
rpmd: 0.00 0.00 0.00 ped_parse: 0.00 0.00 0.00
ism2: 0.00 0.00 0.00 rcm: 0.00 0.00 0.00
csm: 0.00 0.00 0.00 exec_cli: 0.00 0.00 0.00
pm: 0.00 0.00 0.00 syslogd: 0.00 0.00 0.00
inetd: 0.00 0.00 0.00 mount_udrv: 0.00 0.00 0.00
loggd: 0.00 0.00 0.00 mount_mfs: 0.00 0.00 0.00
mount_mfs: 0.00 0.00 0.00 ptdstat_thread: 0.00 0.00 0.00
reboot_thread: 0.00 0.00 0.00 evnt_th: 0.00 0.00 0.00
sccmem_cleanup: 0.00 0.00 0.00 ioflush: 0.00 0.00 0.00
reaper: 0.00 0.00 0.00 pagedaemon: 0.00 0.00 0.00
nfsio: 0.00 0.00 0.00 nfsio: 0.00 0.00 0.00
nfsio: 0.00 0.00 0.00 nfsio: 0.00 0.00 0.00
init: 0.00 0.00 0.00
The following example displays output from the show process command with the detail keyword:
[local]Redback#show process detail
Load Average : 1.30 1.30 1.25
==================================================================
Process (PID) : csm (131)
Spawn count : 1
Memory : 5584K
Time : 00:00:41.29
%CPU : 0.00%
State : run
Up time : 15:01:27
Heart beat : Enabled
Spawn time : 2 seconds
Max crashes allowed : 5
Crash thresh time : 86400 seconds
Total crashes : 0
Images: (Spawns, Max spawns, Version, Path)
(*) 1, 3, v1, /usr/siara/bin/csm -se800
Client IPC Endpoints:
EP 7f000205 c6340001 - MO-RCM-NON-SESS-EP-NAME:00000000
EP 7f000205 c6340001 - IF_CONF-EP-NAME:00000000
EP 7f000205 c6340001 - MO-MGR-BSD-PKT-EP-NAME:00000000
Server IPC Endpoints:
EP 7f000205 c634000a - Active-CSM:00000000
EP 7f000205 c6340001 - CSM-CONF-EP-NAME:00000000
Dependent process aaad (149) EP 7f000205 dab3000e
Dependent process rcm (132) EP 7f000205 caa10001
EP 7f000205 c6340005 - CSM-PPA-EP-NAME:00000000
EP 7f000205 c6340003 - CSM-CLIENT-EP-NAME:00000000
Dependent process ism (133) EP 7f000205 d5860009
Dependent process VX_IPC (-2066809872) EP 7f000203 04000004
==================================================================
Process (PID) : rcm (132)
Spawn count : 1
Memory : 11704K
Time : 00:00:10.94
%CPU : 0.00%
State : run
---(more)---
........
1.26 show process flowd
show process flowd
1.26.1 Purpose
Displays details of the flow process on the current SmartEdge router.
1.26.2 Command Mode
All modes
1.26.3 Syntax Description
This command has no keywords or arguments.
1.26.4 Default
None
1.26.5 Usage Guidelines
Use the show process flowd command to display flow processes on the current SmartEdge router.
- Note:
- By default, most show commands (in any mode) display information for the current context only or, depending on the command syntax, for all contexts. If you are an administrator for the local context, you can insert the optional context ctx-name construct, preceding the show command, to view output for the specified context without entering that context. For more information about using the context ctx-name construct, see the context command description.
- Note:
- By appending a space followed by the pipe ( | ) character at the end of a show command, you can filter the output using a set of modifier keywords and arguments. For more information, see Modifying Output of show Commands in Using the CLI.
1.26.6 Examples
The following example shows how to display the flow processes on the current SmartEdge router:
[local]Redback(config)#show process flowd NAME PID SPAWN MEMORY TIME %CPU STATE flowd 921 21 5920K 00 L:00:14.75 0.00% run
1.27 show process lm
show process lm [crash-info | detail | dmalloc-statistics]
1.27.1 Purpose
Displays label manager (LM) process information.
1.27.2 Command Mode
All modes
1.27.3 Syntax Description
|
crash-info |
Optional. Displays LM process crash information. |
|
detail |
Optional. Displays detailed information. |
|
dmalloc-statistics |
Optional. Displays LM process debug memory allocation statistics. |
1.27.4 Default
None
1.27.5 Usage Guidelines
Use the show process lm command to display LM process information.
- Note:
- By default, most show commands (in any mode) display information for the current context only or, depending on the command syntax, for all contexts. If you are an administrator for the local context, you can insert the optional context ctx-name construct, preceding the show command, to view output for the specified context without entering that context. For more information about using the context ctx-name construct, see the context command description.
- Note:
- By appending a space followed by the pipe ( | ) character at the end of a show command, you can filter the output using a set of modifier keywords and arguments. For more information, see Modifying Output of show Command in Using the CLI.
1.27.6 Examples
The following example displays LM process information:
[local]Redback>show process lm NAME PID SPAWN MEMORY TIME %CPU STATE UP/DOWN lm 41 1 2816K 00:00:01.32 0.00% run 01:10:40
The following example displays LM process crash information:
[local]Redback>show process lm crash-info NAME TIME STATUS lm Mon Mar 29 13:26:47 2005 Trap (133)
The following example displays detailed LM process information:
[local]Redback>show process lm detail Process (PID) : lm (112) Spawn count : 2 Memory : 3016K Time : 00:00:00.31 %CPU : 0.00% State : run Up time : 00:11:09 Heart beat : Enabled Spawn time : 2 seconds Max crashes allowed : 5 Crash thresh time : 86400 seconds Total crashes : 0 Last exit status : Trap (133) Images: (Spawns, Max spawns, Version, Path) (*) 2, 4, v1, /usr/siara/bin/lm Client IPC Endpoints: EP 7f000205 ffdf0007 - LFIB SLOT 03/0:00000000 EP 7f000205 ffdf0007 - LFIB SLOT 03/1:00000000 EP 7f000205 ffdf0007 - RSVP-LM_EP-NAME:00000000 EP 7f000205 ffdf0007 - MPLS-STATIC-LM-EP-NAME:00000000 EP 7f000205 ffdf0006 - ISM2-MBE-EVIN-EP-NAME:00000000 EP 7f000205 ffdf0004 - RIB-IPC-MSG-EP-NAME:00000000 EP 7f000205 ffdf0008 - RSVP-IPC-EP-NAME:00000000 EP 7f000205 ffdf0006 - ISM2-CLIENT-EP-NAME:00000000 EP 7f000205 ffdf0004 - RIB-IPC-RT-EP-NAME:00000000 Server IPC Endpoints: EP 7f000205 ffdf0009 - LBLMGR-CONF-EP-NAME:00000000 Dependent process rcm (28) EP 7f000205 fff70001 EP 7f000205 ffdf0007 - LM-IPC-MSG-EP-NAME:00000000 Dependent process mpls_static (79) EP 7f000205 ffe00001 Dependent process rsvp (65) EP 7f000205 ffe10001 Dependent process ism (29) EP 7f000205 fff90008 Dependent process rib (32) EP 7f000205 fff80015 Dependent process EPPA IPC SLOT 3 (-2130509823) EP 7f000a43 0001000f Dependent process IPPA IPC SLOT 3 (-2147287039) EP 7f000a03 00010010 Dependent process ism (29) EP 7f000205 fff90007
The following example displays LM process debug memory allocation statistics:
[local]Redback>show process lm dmalloc-statistics process: lm, pid: 38 dmalloc_logfile: /flash/dmalloc_log38 open file /flash/dmalloc_log38 failed
1.28 show pseudowire
show pseudowire
1.28.1 Purpose
Displays whether enhanced pseudowire load balancing is enabled or disabled on a router.
1.28.2 Command Mode
All modes
1.28.3 Syntax Description
This command has no keywords or arguments.
1.28.4 Default
None
1.28.5 Usage Guidelines
Use the show pseudowire command to display whether enhanced pseudowire load balancing is enabled or disabled on a router.
Use the pseudowire load balancing command in global configuration mode to enable enhanced pseudowire load balancing on a router. To disable enhanced pseudowire load balancing and return the router to the default setting, in which traffic from all channels of a pseudowire traverse the same path, use the no pseudowire load balancing command.
1.28.6 Examples
The following example shows how to display whether pseudowire load balancing is enabled or disabled on the router. In this example, pseudowire load balancing is enabled:
[local]Redback>show pseudowire multi-path enabled
The following example shows how to display whether pseudowire load balancing is enabled or disabled on the router. In this example, pseudowire load balancing is disabled:
[local]Redback>show pseudowire multi-path disabled
1.29 show public- key
show public-key admin-name
1.29.1 Purpose
Displays an administrator’s public keys.
1.29.2 Command Mode
All modes
1.29.3 Syntax Description
|
admin-name |
Name of the administrator for which public key information is to be displayed. |
1.29.4 Default
None
1.29.5 Usage Guidelines
Use the show public-key command to display an administrator’s public keys.
- Note:
- By default, most show commands (in any mode) display information for the current context only or, depending on the command syntax, for all contexts. If you are an administrator for the local context, you can insert the optional context ctx-name construct before the show command to view output for the specified context without entering that context. For more information about the context ctx-name construct, see the context command description.
- Note:
- By appending a space followed by the pipe ( | ) character at the end of a show command, you can filter the output using a set of modifier keywords and arguments. For more information, see Modifying Output of show Commandsin Using the CLI.
1.29.6 Examples
The following example displays the public keys configured for the jewel administrator:
[local]Redback>show public-key jewel DSA public key(s) for user jewel RSA public key(s) for user jewel 1024 35 138778925487550112496264060257494473953 477802145777234711904931356017804 2535638422909 30011054450485363243280246400199717731319844418831089264593 49685280 91708337898398915273858795 006452667325324989385497 793626010262714937340759030252 164573952317278584144748905148 616886524 97950829684053136276382193869961246761 jewel@pepper
1.30 show qos agent-circuit-id
show qos agent-circuit-id name [detail]
1.30.1 Purpose
Displays the quality of service (QoS) information for the circuit that matches the specified circuit agent ID.
1.30.2 Command Mode
All modes (10)
1.30.3 Syntax Description
|
name |
Name of the specific circuit agent ID. Alphanumeric string of up to 63 characters. |
|
detail |
Optional. Displays details for each circuit agent ID. |
1.30.4 Default
When entered without any optional syntax, displays brief QoS information about the circuit.
1.30.5 Usage Guidelines
Use the show qos agent-circuit-id command to display the QoS information for the circuit that matches the specified circuit agent ID.
- Note:
- By appending a space followed by the pipe ( | ) character at the end of a show command, you can filter the output using a set of modifier keywords and arguments. For more information, see Modifying Output of show Commandsin Using the CLI.
1.30.6 Examples
The following example shows the circuit shaping information for the circuit that matches the circuit agent ID dslam2:
[local]Redback>show qos agent-circuit-id dslams
Circuit Policy Name Type Rate Source
5/2 vlan-id 2 pppoe 1021 gold pwfq 20000 local
meter3 metering 10000 local
The following example shows details for the circuit agent ID:
[local]Redback>show qos agent-circuit-id dslam2 detail Circuit: 5/2 vlan-id 2 pppoe 1021 ---------------------------------------------------------- Policy Name : gold Policy Type : pwfq Queue position : 25 Num Queues : 4 Rate : 20000 Rate Source : local Policy Name : meter3 Policy Type : metering Rate : 10000 Rate Source : local Burst : 20000 Excess Burst : 30000
1.31 show qos circuit
show qos circuit [ circuit-group name] {[slot/port [:chan-num [:sub-chan-num]] {dlci-id | vpi-vci vpi vci | vlan vlan-id} [detail]]}
1.31.1 Purpose
Displays the quality of service (QoS) information for all circuits or a particular circuit in the system.
1.31.2 Command Mode
All modes
1.31.3 Syntax Description
|
circuit-group name |
Optional. Displays the QoS options configured for the specified circuit group. |
|
slot |
Optional. Chassis slot number of a line card for which circuit information is displayed. If omitted, displays circuit information for all circuits in the system. |
|
port |
Optional. Port number for which circuit information is displayed. Required if you enter the slot argument. |
|
chan-num |
Optional. Channel number for which circuit information is displayed. If omitted, displays circuit information for all channels on the specified port. The range of values depends on the type of port. |
|
sub-chan-num |
Optional. Subchannel number for which circuit information is displayed. If omitted, displays circuit information for all subchannels in the specified channel. The range of values depends on the type of por. |
|
lg lg-id |
Optional. Displays all the circuits associated with the specified link or APS group. |
|
dlci-id |
Optional. Data-link collection identifier (DLCI) for the Frame Relay permanent virtual circuit (PVC). The range of values is 16 to 991. |
|
vpi-vci vpi vci |
Optional. Virtual path identifier (VPI) and virtual channel identifier (VCI) for an Asynchronous Transfer Mode (ATM) PVC. The range of values is 0 to 255 and 1 to 65,535, respectively. |
|
vlan vlan-id |
Optional. Virtual LAN (VLAN) tag value for an 802.1Q tunnel or a PVC. The vlan-id argument is one of the following constructs:
The range of values for any VLAN tag value is 1 to 4,095. |
|
detail |
Optional. Displays details for each PVC. |
1.31.4 Default
None
1.31.5 Usage Guidelines
Use the show qos circuit command to display the QoS information for all circuits, a particular circuit, or a circuit group in the system.
Use the circuit-group name construct to display the QoS options configured for the specified circuit group.
If you enter the optional slot, or port, and chan-num arguments, the command displays circuit information for all circuits configured on the specified card, or port, or channel; if you enter the optional sub-chan-num argument, the command displays circuit information for all circuits configured on the DS-1 channel or DS-0 channel group.
Use the the vpi-vci vpi vci construct to display the VPI and VCI for an ATM PVC and VLAN tag value to display the value of an 802.1Q tunnel or PVC.
- Note:
- By appending a space followed by the pipe ( | ) character at the end of a show command, you can filter the output using a set of modifier keywords and arguments. For more information, see Modifying Output of show Commands in Using the CLI.
1.31.6 Examples
The following example shows how to display circuit shaping information:
[local]Redback>show qos circuit
Circuit Policy Name Type Rate Source
5/2 vlan-id 2 pppoe 1017 gold pwfq 20000 local
meter3 metering 10000 local
5/2 vlan-id 2 pppoe 1018 gold pwfq 20000 local
meter3 metering 10000 local
5/2 vlan-id 2 pppoe 1019 gold pwfq 20000 local
meter3 metering 10000 local
5/2 vlan-id 2 pppoe 1020 gold pwfq 20000 local
meter3 metering 10000 local
5/2 vlan-id 2 pppoe 1021 gold pwfq 20000 local
meter3 metering 10000 local
The following example displays detail information about a QoS circuit when an incremental rate adjustment is applied using the rate-adjust dhcp pwfq command. The field, Rate Offset, indicates the incremental rate applied to the circuit (for information about the rate-adjust dhcp pwfq command, see the Command List):
[local]Redback>show qos circuit detail Circuit: 2/2 vlan-id 2 Policy Name: SAVEMART Policy Type: pwfq Rate: 20000 Rate Source: local Dynamic Parameters Priority Group 1: Rate: 4000 Rate Offset: -1000
The following example shows how to display QoS options configured for the cg1 circuit group:
[local]Redback>show qos circuit circuit-group cg1 Circuit Policy Name Type Rate Source circuit-group cg1 meter7 metering H - local
The following example shows how to display detailed information about the QoS options configured for the cgi circuit group:
[local]Redback>show qos circuit circuit-group cg1 detail circuit-group cg1 ---------------------------------------------------------- Policy Name : policing2 Policy Type : policing Hierarchical Type : Hierarchical Parent Rate : 80000 Rate Source : local Burst : 100000 Excess Burst : 265000 Policy Name : metering2 Policy Type : metering Hierarchical Type : Hierarchical Parent Rate : 80000 Rate Source : local Burst : 100000 Excess Burst : 265000
1.32 show qos class-definition
show qos class-definition [class-definition-name]
1.32.1 Purpose
Displays the contents of quality of service (QoS) class definitions.
1.32.2 Command Mode
Exec
1.32.3 Syntax Description
|
class-definition-name |
Optional. An alphanumeric string up to 39 characters that specifies the class definition name. |
1.32.4 Default
If you do not specify the class-definition-name argument, a list of all QoS class definitions is displayed. If you specify the class-definition-name argument, detailed information about the specified QoS class definition is displayed.
1.32.5 Usage Guidelines
Use the show qos class-definition command to display the contents of QoS class definitions.
The command output displays a class definition table. This includes all possible packet descriptor (PD) classification values sorted by the priority value (from 0 to 7) and then sorted by the drop precedence value (from 0 to 7). Use the following formula to convert these values to the 6-bit values (0 to 63) used to configure PD class definition map entries:
six-bit-value = (8 * priority-value) + drop-value.
Each entry in the table contains either a numerical class ID value from 0 to 7 or a hyphen (-) to indicate that a PD value has not been assigned to the class. After the class definition table is another table that maps class ID values assigned by the system to the class names configured by the administrator.
- Note:
- By appending a space followed by the pipe ( | ) character at the end of a show command, you can filter the output using a set of modifier keywords and arguments. For more information, see Modifying Output of show Commandsin Using the CLI.
1.32.6 Examples
The following example displays a list of all QoS class definitions:
[local]Redback#show qos class-definition Class Definition Id auo 1 rar 2 my_classes 3 Total QoS class definitions: 3
The following example displays detailed information about the my_classes QoS class definition:
[local]Redback#show qos class-definition my_classes Class Definition Id my_classes 3 drop value - 0 - 1 - 2 - 3 - 4 - 5 - 6 - 7 - priority 0 - 1 2 3 4 5 6 7 priority 1 1 1 2 1 1 1 1 1 priority 2 1 1 1 1 1 1 1 1 priority 3 1 1 1 1 1 1 1 1 priority 4 1 1 1 1 1 1 1 1 priority 5 1 1 1 1 1 1 1 1 priority 6 1 1 1 1 1 1 1 1 priority 7 1 1 1 1 1 1 1 - Class Name Entry Count 1 default 55 2 two 2 3 three 1 4 four 1 5 five 1 6 six 1 7 seven 1 Total QoS class definitions: 1
1.33 show qos class-map
show qos class-map [map-name]
1.33.1 Purpose
Displays quality of service (QoS) classification map information.
1.33.2 Command Mode
All modes
1.33.3 Syntax Description
|
map-name |
Optional. Name of the classification map. |
1.33.4 Default
If you do not specify the map-name argument, a list of all classification maps is displayed. If you specify the map-name argument, detailed information about the specified classification map is displayed.
1.33.5 Usage Guidelines
Use the show qos class-map command to display QoS classification map information. Use the optional syntax to narrow the command output.
In command output, a default secondary mapping for inbound QoS packets to Differentiated Services Code Point (DSCP) packets is represented in the table by the string dscp. A custom secondary mapping is indicated by the string cnnnn, where nnnn is the ID number of the secondary class map.
PD and DSCP values are displayed in the format p:d, where p is a priority value from 0 to 7 and d is a drop-precedence value from 0 to 7. To convert these values to the 6-bit (0 to 63) values used to configure PD and DSCP classification map entries, use the following formula:
value = (8 * priority-value) + drop-value
- Note:
- By appending a space followed by the pipe ( | ) character at the end of a show command, you can filter the output using a set of modifier keywords and arguments. For more information, see Modifying Output of show Commands in Using the CLI.
1.33.6 Examples
The following example displays QoS mapping information without specifying a classification map:
[local]Redback#show qos class-map Classification Map Type Direction Id dscp-to-pd ip in 67 exp-to-pd mpls in 68 pd-to-exp mpls out 69 dscp-to-exp mpls out 70 Total QoS classification maps: 4
The following examples display output from the show qos class-map command when a classification map is specified:
[local]Redback#show qos class-map dscp-to-pd
Classification Map Type Direction Id
dscp-to-pd ip in 66
drop value - 0 - 1 - 2 - 3 - 4 - 5 - 6 - 7 -
priority 0 1:6 0:0 1:6 1:6 1:6 1:6 1:6 1:6
priority 1 1:6 1:6 1:6 1:6 1:6 1:6 1:6 1:6
priority 2 1:6 1:6 3:1 1:6 1:6 1:6 1:6 1:6
priority 3 1:6 1:6 1:6 1:6 1:6 1:6 1:6 1:6
priority 4 1:6 1:6 1:6 1:6 1:6 1:6 1:6 1:6
priority 5 1:6 1:6 1:6 1:6 1:6 1:6 1:6 1:6
priority 6 1:6 1:6 1:6 1:6 1:6 1:6 1:6 1:6
priority 7 1:6 1:6 1:6 1:6 1:6 1:6 1:6 1:6
Total QoS classification maps: 1
[local]Redback#show qos class-map exp-to-pd
Classification Map Type Direction Id
exp-to-pd mpls in 67
priority:drop
priority 0 0:0
priority 1 4:4
priority 2 dscp
priority 3 c0066
priority 4 4:6
priority 5 4:2
priority 6 6:0
priority 7 5:6
Total QoS classification maps: 1
[local]Redback#show qos class-map pd-to-exp
Classification Map Type Direction Id
pd-to-exp mpls out 68
drop value - 0 - 1 - 2 - 3 - 4 - 5 - 6 - 7 -
priority 0 1 0 0 0 0 0 0 0
priority 1 1 1 1 1 1 1 1 1
priority 2 2 2 2 2 2 2 2 2
priority 3 3 3 3 3 3 3 3 3
priority 4 4 4 4 4 4 4 4 4
priority 5 5 5 5 5 5 5 7 5
priority 6 6 6 6 6 6 6 6 6
priority 7 7 7 7 7 7 7 7 7
Total QoS classification maps: 1
[local]Redback#show qos class-map dscp-to-exp
Classification Map Type Direction Id
dscp-to-exp mpls out 69
drop value - 0 - 1 - 2 - 3 - 4 - 5 - 6 - 7 -
priority 0 c0068 c0068 c0068 c0068 c0068 c0068 c0068 c0068
priority 1 c0068 c0068 c0068 c0068 c0068 dscp c0068 c0068
priority 2 c0068 c0068 c0068 c0068 c0068 c0068 c0068 c0068
priority 3 c0068 c0068 c0068 c0068 c0068 c0068 4 c0068
priority 4 c0068 c0068 c0068 c0068 c0068 c0068 c0068 c0068
priority 5 c0068 c0068 c0068 c0068 c0068 c0068 c0068 c0068
priority 6 c0068 c0068 c0068 c0068 c0068 c0068 c0068 c0068
priority 7 c0068 c0068 c0068 c0068 c0068 c0068 c0068 c0068
Total QoS classification maps: 1
1.34 show qos client
show qos client [{slot slot [{eppa | ippa}]}]
1.34.1 Purpose
Displays quality of service (QoS) Packet Processing ASIC (PPA) client information.
1.34.2 Command Mode
All modes
1.34.3 Syntax Description
|
slot slot |
Optional. Slot number for the ingress or egress PPA. |
|
eppa |
Optional. Displays client information for the slot’s egress PPA. |
|
ippa |
Optional. Displays client information for the slot’s ingress PPA. |
1.34.4 Default
If you enter this command without any optional syntax, client information for all slots, both egress and ingress, is displayed.
1.34.5 Usage Guidelines
Use the show qos client command to display QoS PPA client information. Use the optional syntax to narrow the command output.
- Note:
- The SmartEdge 100 router limits the value of the slot argument to 2.
- Note:
- By default, most show commands (in any mode) display information for the current context only or, depending on the command syntax, for all contexts. If you are an administrator for the local context, you can insert the optional context ctx-name construct, preceding the show command, to view output for the specified context without entering that context. For more information about using the context ctx-name construct, see the context command description.
- Note:
- By appending a space followed by the pipe ( | ) character at the end of a show command, you can filter the output using a set of modifier keywords and arguments. For more information, see Modifying Output of show Commandsin Using the CLI.
1.34.6 Examples
The following example displays PPA client information without specifying a slot:
[local]Redback>show qos client Slot#: 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 iPPA: Dnld: * * * * * * * * * * * * * * Reborn: Register: * ePPA: Dnld: Reborn: Register: *
The following example displays output from the show qos client command when a slot is specified:
[local]Redback>show qos client slot 13 QoS Client on Slot-13 iPPA: Wait for Dnld: n, Wait for reborn n, Registered: y QoS Client on Slot-13 ePPA: Wait for Dnld: n, Wait for reborn n, Registered: y
1.35 show qos congestion-map
show qos congestion-map map-name
1.35.1 Purpose
Displays the queue assignments for the specified quality of service (QoS) congestion avoidance map.
1.35.2 Command Mode
All modes
1.35.3 Syntax Description
|
map-name |
Name of the QoS congestion avoidance map. |
1.35.4 Default
None
1.35.5 Usage Guidelines
Use the show qos congestion-map command to display the queue assignments for the specified QoS congestion avoidance map.
- Note:
- By default, most show commands (in any mode) display information for the current context only or, depending on the command syntax, for all contexts. If you are an administrator for the local context, you can insert the optional context ctx-name construct, preceding the show command, to view output for the specified context without entering that context. For more information about using the context ctx-name construct, see the context command description.
- Note:
- By appending a space followed by the pipe ( | ) character at the end of a show command, you can filter the output using a set of modifier keywords and arguments. For more information, see Modifying Output of show Commands in Using the CLI.
1.35.6 Examples
The following example displays the queue assignments for the red-pwfq QoS congestion avoidance map:
[local]Redback>show qos congestion-map red-pwfq Congestion-Avoidance Map Type Mode Grid Q-0 1 2 3 4 5 6 7 red-pwfq pwfq RED 1 y Total QoS congestion-avoidance maps: 1
The following example displays queue parameters for the congestion avoidance map:
[local]Redback#show qos congestion-map test-cmap Congestion-Avoidance Map: test-cmap, Type: pwfq, Grid: 1 Queue: 0 , Mode: Random Early Drop Exp. Weight: 12, Queue Depth (Pkts): 10000 Drop profile: default Prob. Min. Threshold Max. Threshold 10 1000 5000 Drop profile: profile-1 Dscp list: 0, 1, 2, 3, 4, 5, 6, 7, 8, 9, 10, 11, 12, 13, 14, 15, 16, 17, 18, 19, 20, 21 Prob. Min. Threshold Max. Threshold 2000 100 1000 Drop profile: profile-2 Dscp list: 33, 34, 35, 36, 37, 38, 39, 40, 41, 42, 43 Prob. Min. Threshold Max. Threshold 2000 100 1000 Queue: 1 , Mode: Random Early Drop Queue Depth (Pkts): 65535 Drop profile: default Prob. Min. Threshold Max. Threshold 32767 1 10000 Drop profile: profile-1 Dscp list: 39, 44, 45, 49, 50, 51, 52, 54 Prob. Min. Threshold Max. Threshold 32767 1 10000 Total QoS congestion-avoidance maps: 1 [local]Redback#
1.36 show qos h-node
show qos h-node [slot slot]
1.36.1 Purpose
Displays quality of service (QoS) hierarchical node information.
1.36.2 Command Mode
All modes
1.36.3 Syntax Description
|
slot slot |
Optional. Slot number for the Gigabit Ethernet (GE) line card. |
1.36.4 Default
When entered without any optional syntax, the show qos h-node command displays hierarchical node information for all slots.
1.36.5 Usage Guidelines
Use the show qos h-node command to display QoS hierarchical node information. Use the optional slot slot construct to display output for a single Gigabit Ethernet line card.
- Note:
- The SmartEdge 100 router limits the value of the slot argument to 2.
- Note:
- Hierarchical nodes are supported only on traffic-managed ports and circuits.
- Note:
- By default, most show commands (in any mode) display information for the current context only or, depending on the command syntax, for all contexts. If you are an administrator for the local context, you can insert the optional context ctx-name construct, preceding the show command, to view output for the specified context without entering that context. For more information about using the context ctx-name construct, see the context command description.
- Note:
- By appending a space followed by the pipe ( | ) character at the end of a show command, you can filter the output using a set of modifier keywords and arguments. For more information, see Modifying Output of show Commands in Using the CLI.
1.36.6 Examples
The following example displays hierarchical node information for the ports on the GE3 line card in slot 13:
[local]Redback>show qos h-node slot 13
Sl/Po L Name & index/Cct-handle Id PrId Ccts M Min-rat/bst Max-rat/bst D 13/1 L4 13/1:1023:63/9/0/161 1 0 0 s 0 /0 0 /0 Total QoS hierarchical nodes: 1
1.37 show qos memory
show qos memory
1.37.1 Purpose
Displays quality of service (QoS) daemon memory usage information.
1.37.2 Command Mode
All modes
1.37.3 Syntax Description
This command has no keywords or arguments.
1.37.4 Default
None
1.37.5 Usage Guidelines
Use the show qos memory command to display QoS daemon memory usage information.
- Note:
- By default, most show commands (in any mode) display information for the current context only or, depending on the command syntax, for all contexts. If you are an administrator for the local context, you can insert the optional context ctx-name construct, preceding the show command, to view output for the specified context without entering that context. For more information about using the context ctx-name construct, see the context command description.
- Note:
- By appending a space followed by the pipe ( | ) character at the end of a show command, you can filter the output using a set of modifier keywords and arguments. For more information, see Modifying Output of show Commands in Using the CLI.
1.37.6 Examples
The following example displays output from the show qos memory command:
[local]Redback>show qos memory Chunk_Size Curr_InUse Max_In_Use TotalAlloc Total_Free Name 24 0 0 0 0 task_block 84 3 3 3 0 task_size_block 196 4 4 4 0 QOS_CKT 356 0 4 6 6 QOS_CONFQ 812 2 2 2 0 QOS_POLMAP
1.38 show qos policy
show qos policy
1.38.1 Purpose
Displays information for all configured quality of service (QoS) policies.
1.38.2 Command Mode
All modes
1.38.3 Syntax Description
This command has no keywords or arguments.
1.38.4 Default
None
1.38.5 Usage Guidelines
Use the show qos policy command to display information for all configured QoS policies.
Table 24 describes the output fields for the show qos policy command.
|
Field Name |
Description |
|---|---|
|
Policy-Name |
Policy name. |
|
Type |
Type of policy. |
|
Grid |
Unique policy identifier. |
|
Qs |
Number of queues that each circuit consumes when it is bound to this policy. This field applies only to Asynchronous Transfer Mode weighted fair queuing (ATMWFQ), enhanced deficit round-robin (EDRR), and priority queuing (PQ) policies. |
|
Slot |
Number of slots where the policy has been downloaded. |
|
Port |
Number of circuits currently bound to this policy. |
|
Bound |
Indicates the direction of the bound policy: in or out. If there are no bindings, this field is blank. |
|
Dnld |
Download in progress. A “Y” entry in this field indicates the policy is being downloaded to a line card; otherwise, this field is blank. |
|
Status |
Download status. If this field is blank, the policy has been downloaded to the line card. An “updt” entry indicates a policy update is pending download. A “del” entry indicates a policy deletion is pending download. |
- Note:
- By default, most show commands (in any mode) display information for the current context only or, depending on the command syntax, for all contexts. If you are an administrator for the local context, you can insert the optional context ctx-name construct, preceding the show command, to view output for the specified context without entering that context. For more information about using the context ctx-name construct, see the context command description.
- Note:
- By appending a space followed by the pipe ( | ) character at the end of a show command, you can filter the output using a set of modifier keywords and arguments. For more information, see Modifying Output of show Commands in Using the CLI.
1.38.6 Examples
The following example displays information for all configured QoS policies:
[local]Redback>show qos policy Policy-Name Type Grid Qs Slots Ports Bound DnLd Status prl-special prl 1 0 0 0 updt mtr-special metering 2 0 0 0 updt plc-special police 3 0 0 0 updt pq-special pq 4 8 0 0 updt Total policy map: 4
1.39 show qos policy atmwfq
show qos policy atmwfq [{pol-name | default-value}]
1.39.1 Purpose
Displays information about one or more configured quality of service (QoS) Asynchronous Transfer Mode weighted fair queuing (ATMWFQ) policies.
1.39.2 Command Mode
All modes
1.39.3 Syntax Description
|
pol-name |
Optional. Name of an ATMWFQ policy. |
|
default-value |
Optional. Displays information about ATMWFQ policy default values. |
1.39.4 Default
When entered without any optional syntax, displays brief information about all configured ATMWFQ policies.
1.39.5 Usage Guidelines
Use the show qos policy atmwfq command to display information about one or more configured QoS ATMWFQ policies.
Use the pol-name argument to display detailed information about a single QoS ATMWFQ policy.
- Note:
- By default, most show commands (in any mode) display information for the current context only or, depending on the command syntax, for all contexts. If you are an administrator for the local context, you can insert the optional context ctx-name construct, preceding the show command, to view output for the specified context without entering that context. For more information about using the context ctx-name construct, see the context command description.
- Note:
- By appending a space followed by the pipe ( | ) character at the end of a show command, you can filter the output using a set of modifier keywords and arguments. For more information, see Modifying Output of show Commands in Using the CLI.
1.39.6 Examples
The following example displays brief information about all configured QoS ATMWFQ policies:
[local]Redback>show qos policy atmwfq Policy-Name Type Grid Qs atmwfq1 atmwfq 1 4 Total QoS policy map: 1
The following example displays detailed information about the ATMWFQ policy, atmwfq1:
[local]Redback>show qos policy atmwfq atmwfq1 Policy-Name Type Grid Qs atmwfq1 atmwfq 1 4 Qnum Red Prob Weight Min Max Traffic-weight 0 0xf 9 9 5 15 10 1 0xf 9 9 5 15 10 2 0xf 9 9 5 15 10 3 0xf 9 9 5 15 10
The following example displays detailed information for the ATMWFQ policy, ds3_cosq.22001.119.3:
[local]Redback>show qos policy atm ds3_cosq.22001.119.3 Policy-Name Type Grid Qs ds3_cosq.22001.119.3 atmwfq 1 2 Queue-map: default Qnum Red Prob Weight Min Max Traffic-Weight Mode 0 0xf 22515 7 10359 10417 361 alternate 1 0xf 20880 8 638 6176 493 Total policy map: 1
1.40 show qos policy edrr
show qos policy edrr [{pol-name | default-value}]
1.40.1 Purpose
Displays information about one or more quality of service (QoS) enhanced deficit round-robin (EDRR) policies.
1.40.2 Command Mode
All modes
1.40.3 Syntax Description
|
pol-name |
Optional. Name of an EDRR policy. |
|
default-value |
Optional. Displays information about EDRR policy default values. |
1.40.4 Default
When entered without any optional syntax, displays brief information about all configured EDRR policies.
1.40.5 Usage Guidelines
Use the show qos policy edrr command to display QoS EDRR policy information.
Use the pol-name argument to display detailed information about a single QoS EDRR policy.
- Note:
- By default, most show commands (in any mode) display information for the current context only or, depending on the command syntax, for all contexts. If you are an administrator for the local context, you can insert the optional context ctx-name construct, preceding the show command, to view output for the specified context without entering that context. For more information about using the context ctx-name construct, see the context command description.
- Note:
- By appending a space followed by the pipe ( | ) character at the end of a show command, you can filter the output using a set of modifier keywords and arguments. For more information, see Modifying Output of show Commands in Using the CLI.
1.40.6 Examples
The following example displays brief information about all configured EDRR policies:
[local]Redback>show qos policy edrr Policy Name Type Grid Qs slot Port Bound DnLd Status drr edrr 11 8 1 2 Out
1.41 show qos policy metering
show qos policy metering [{pol-name | default-value}]
1.41.1 Purpose
Displays information about one or more configured quality of service (QoS) metering policies.
1.41.2 Command Mode
All modes
1.41.3 Syntax Description
|
pol-name |
Optional. Name of a metering policy. |
|
default-value |
Optional. Displays information about metering policy default values. |
1.41.4 Default
When entered without any optional syntax, displays brief information about all configured QoS metering policies.
1.41.5 Usage Guidelines
Use the show qos policy metering command to display information about one or more configured QoS metering policies.
Use the pol-name argument to display detailed information about a single QoS metering policy.
- Note:
- By default, most show commands (in any mode) display information for the current context only or, depending on the command syntax, for all contexts. If you are an administrator for the local context, you can insert the optional context ctx-name construct, preceding the show command, to view output for the specified context without entering that context. For more information about using the context ctx-name construct, see the context command description.
- Note:
- By appending a space followed by the pipe ( | ) character at the end of a show command, you can filter the output using a set of modifier keywords and arguments. For more information, see Modifying Output of show Commands in Using the CLI.
1.41.6 Examples
The following example displays brief information about all QoS metering policies:
[local]Redback>show qos policy metering Policy-Name Type Grid Qs Slot Port Bound DnLd Status meter meter 1 0 1 5 in Total QoS policy map: 1
The following example displays detailed information about the QoS metering policy, meter:
[local]Redback>show qos policy metering meter Policy-Name Type Grid Qs Slot Port Bound DnLd Status meter meter 1 0 1 5 in Slot#: 1 2 3 4 5 6 7 8 9 10 11 12 13 14 iPPA dnld: ePPA dnld: iPPA ports: 5 ePPA ports: Total QoS policy map: 1
1.42 show qos policy policing
show qos policy policing [{pol-name | default-value}]
1.42.1 Purpose
Displays information about one or more configured quality of service (QoS) policing policies.
1.42.2 Command Mode
All modes
1.42.3 Syntax Description
|
pol-name |
Optional. Name of a policing policy. |
|
default-value |
Optional. Displays information about policing policy default values. |
1.42.4 Default
When entered without any optional syntax, displays brief information about all configured QoS policing policies.
1.42.5 Usage Guidelines
Use the show qos policy policing command to display information about one or more configured QoS policing policies.
Use the pol-name argument to display detailed information about a single QoS policing policy.
Table 25 describes the output fields for the show qos policy policing command.
|
Field Name |
Description |
|---|---|
|
Policy-Name |
Policy name. |
|
Type |
Type of policy. |
|
Grid |
Unique policy identifier. |
|
Qs |
Number of queues that each circuit consumes when it is bound to this policy. This field applies only to Asynchronous Transfer Mode (ATM) weighted fair queuing (WFQ), enhanced deficit round-robin (EDRR), and priority queuing (PQ) policies. |
|
Slot |
Number of slots where the policy has been downloaded. |
|
Port |
Number of circuits currently bound to this policy. |
|
Bound |
Indicates the direction of the bound policy: “in” or “out”. If there are no bindings, this field is blank. |
|
Dnld |
Download in progress. A “Y” entry indicates the policy is being downloaded to a line card. Otherwise, this field is blank. |
|
Status |
Download status. If this field is blank, the policy has been downloaded to the line card. An “updt” entry indicates a policy update is pending download. A “del” entry indicates a policy deletion is pending download. |
When a policy name is specified, in addition to the information described in Table 25, the distribution of QoS bindings across line card slots is displayed.
- Note:
- By default, most show commands (in any mode) display information for the current context only or, depending on the command syntax, for all contexts. If you are an administrator for the local context, you can insert the optional context ctx-name construct, preceding the show command, to view output for the specified context without entering that context. For more information about using the context ctx-name construct, see the context command description.
- Note:
- By appending a space followed by the pipe ( | ) character at the end of a show command, you can filter the output using a set of modifier keywords and arguments. For more information, see Modifying Output of show Commands in Using the CLI.
1.42.6 Examples
The following example displays brief information for all QoS policing policies:
[local]Redback>show qos policy policing Policy-Name Type Grid Qs Slot Port Bound DnLd Status police police 1 0 1 5 in Total QoS policy map: 1
The following example displays detailed information about the QoS policing policy, police, which is bound to 15 circuits on the line card in slot 9 and to 15 circuits on the line card in slot 11:
[local]Redback>show qos policy policing police Policy-Name Type Grid Qs Slot Port Bound DnLd Status police police 6 0 1 30 in updt Slot#: 1 2 3 4 5 6 7 8 9 10 11 12 13 14 iPPA dnld: ePPA dnld: iPPA ports: 15 15 ePPA ports: Rate(kbps): 2000 Bursts(bytes): 15000 Conf-mark-dscp Conf-drop Exceed-mark-dscp exceed-drop 0x2e 0x0
1.43 show qos policy pq
show qos policy pq [pol-name | default-value]
1.43.1 Purpose
Displays information about one or more configured quality of service (QoS) priority queuing (PQ) policies.
1.43.2 Command Mode
All modes
1.43.3 Syntax Description
|
pol-name |
Optional. Name of the PQ policy. |
|
default-value |
Optional. Displays information about PQ policy default values. |
1.43.4 Default
When entered without any optional syntax, this command displays information about all configured PQ policies.
1.43.5 Usage Guidelines
Use the show qos policy pq command to display information about one or more QoS PQ policies.
Use the pol-name argument to display detailed information about a single QoS PQ policy.
- Note:
- By default, most show commands (in any mode) display information for the current context only or, depending on the command syntax, for all contexts. If you are an administrator for the local context, you can insert the optional context ctx-name construct, preceding the show command, to view output for the specified context without entering that context. For more information about using the context ctx-name construct, see the context command description.
- Note:
- By appending a space followed by the pipe ( | ) character at the end of a show command, you can filter the output using a set of modifier keywords and arguments. For more information, see Modifying Output of show Commands in Using the CLI.
1.43.6 Examples
The following example displays brief information for all QoS PQ policies:
[local]Redback>show qos policy pq default-value priority queueing policy default values: number of queues 8 Qnum Change Red Rate Burst E Prob Weight Min Max Depth 0 max max y 10 9 10 18 1000 1 max max y 10 9 11 18 1000 2 max max y 10 9 12 18 1000 3 max max y 10 9 13 18 1000 4 max max y 10 9 14 18 1000 5 max max y 10 9 15 18 1000 6 max max y 10 9 16 18 1000 7 max max y 10 9 17 18 1000 ( * max=2147483647)
The following example displays detailed information for the PQ policy, special1:
[local]Redback>show qos policy pq special1 Policy-Name Type Grid Qs Slot Port Bound DnLd Status special1 pq 1 8 0 0 updt Slot#: 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 iPPA dnld: ePPA dnld: iPPA ports: ePPA ports: Queues updated: 0, 1, 2, 3, 4, 5, 6, 7, Qnum Change Red Rate Burst E Prob Weight Min Max Depth 0 0x0 0x0 1000000 5555 n 100 23 40 900 500 1 0x0 0x0 50000 1000 y 200 22 50 800 1000 2 0x0 0x0 max max y 300 21 70 700 1000 3 0x0 0x0 max max y 400 20 80 600 1000 4 0x0 0x0 max max y 500 19 90 500 1000 5 0x0 0x0 max max y 10 9 15 18 1000 6 0x0 0x0 max max y 10 9 16 18 1000 7 0x0 0x0 max max y 1 0 9 17 18 1000 Total QoS policy map: 1
1.44 show qos policy protocol-rate-limit
show qos policy protocol-rate-limit [pol-name ]
1.44.1 Purpose
Displays information about one or more configured quality of service (QoS) protocol-specific rate-limiting policies.
1.44.2 Command Mode
All modes
1.44.3 Syntax Description
|
pol-name |
Optional. Name of the protocol-specific rate-limiting policy. |
1.44.4 Default
When entered without any optional syntax, this command displays information about all configured protocol-specific rate-limiting policies in the current context.
1.44.5 Usage Guidelines
Use the show qos policy protocol-rate-limit command to display information about all protocol-specific rate-limiting policies configured in the current context, or to display information about a specific protocol-specific rate-limiting policy. When issued for a specific policy, this command shows the configured values for the relevant protocol.
- Note:
- By default, most show commands (in any mode) display information for the current context only or, depending on the command syntax, for all contexts. If you are an administrator for the local context, you can insert the optional context ctx-name construct, preceding the show command, to view output for the specified context without entering that context. For more information about using the context ctx-name construct, see the context command description.
- Note:
- By appending a space followed by the pipe ( | ) character at the end of a show command, you can filter the output using a set of modifier keywords and arguments. For more information, see Modifying Output of show Commands in Using the CLI.
1.44.6 Examples
The following example displays the values for the special protocol-specific rate-limiting policy:
[local]Redback>show qos policy protocol-rate-limit special
Policy-Name Type Grid Qs Slots Ports Bound DnLd Status
special prl 1 0 0 0 updt
Slot#: 1 2 3 4 5 6 7 8 9 10 11 12 13 14
iPPA dnld:
ePPA dnld:
iPPA ports:
ePPA ports:
Protocol: ARP
Rate(pkts/sec): 1000 Burst(pkts): 15000
Total policy map: 1
1.45 show qos policy pwfq
show qos policy pwfq [pol-name | default-value]
1.45.1 Purpose
Displays information about one or more configured quality of service (QoS) priority weighted fair queuing (PWFQ) policies.
1.45.2 Command Mode
All modes
1.45.3 Syntax Description
|
pol-name |
Optional. Name of the PWFQ policy. |
|
default-value |
Optional. Displays information about PWFQ policy default values. |
1.45.4 Default
When entered without any optional syntax, this command displays information about all configured PQ policies in the current context.
1.45.5 Usage Guidelines
Use the show qos policy pwfq command to display information about all PWFQ policies configured in the current context, or to display information about a specific PWFQ policy.
- Note:
- PWFQ policies are supported only on traffic-managed ports and circuits.
- Note:
- By default, most show commands (in any mode) display information for the current context only or, depending on the command syntax, for all contexts. If you are an administrator for the local context, you can insert the optional context ctx-name construct, preceding the show command, to view output for the specified context without entering that context. For more information about using the context ctx-name construct, see the context command description.
- Note:
- By appending a space followed by the pipe ( | ) character at the end of a show command, you can filter the output using a set of modifier keywords and arguments. For more information, see Modifying Output of show Commands in Using the CLI.
1.45.6 Examples
The following example displays the values for the pwfq-port PWFQ policy:
[local]Redback>show qos policy pwfq pwfq-port
Policy-Name Type Grid Qs Slots Ports Bound DnLd Status pwfq-port pwfq 12 8 0 0 updt Slot#: 1 2 3 4 5 6 7 8 9 10 11 12 13 14 iPPA dnld: ePPA dnld: iPPA ports: ePPA ports: Max-Q-Depth: 0, Queues updated: none Queue-map: default Total policy map: 1
1.46 show qos port
show qos port [slot slot]
1.46.1 Purpose
Displays active quality of service (QoS) binding information for ports on one or more line cards.
1.46.2 Command Mode
All modes
1.46.3 Syntax Description
|
slot slot |
Optional. Slot number of line card for which QoS binding information is displayed. |
1.46.4 Default
When entered without any optional syntax, displays active QoS binding information for ports on all line cards.
1.46.5 Usage Guidelines
Use the show qos port command to active display QoS binding information for ports on one or more line cards.
- Note:
- The SmartEdge 100 router limits the value of the slot argument to 2.
Table 26 describes the output fields for this command.
|
Field |
Description |
|---|---|
|
Slot/Port |
Slot and port to which the QoS policy is bound. |
|
(vlan-id) |
For QoS policies that are bound to PVCs or subscribers, the PVC number is displayed. Otherwise, this field is blank. |
|
PVC |
A “y” entry indicates that the binding is applied to a PVC or to a subscriber. Otherwise, this field is blank. |
|
Policy-Name |
Name of bound QoS policy. |
|
Port |
Active port to which the QoS policy is bound. |
|
Qpos |
Displays the first queue reserved for the QoS binding. This field is applicable only to enhanced deficit round-robin (EDRR) and priority queuing (PQ) policies. For all other QoS policies, this field is blank. |
|
L |
Number of queues used for this binding. The value is configured through the EDRR or PQ policy that is bound to the circuit. The value in the Qpos field combined with the value in this field provides the queue numbers. For example, if the Qpos field is 96 and this field is 8, the queues used for the binding are 96, 97, 98, 99, 100, 101, 102, and 103. |
|
Bound |
Indicates the direction of the bound policy: “in” or “out”. |
|
L4/L3 |
Refers to the h-node ID with which the queuing policy is associated. |
- Note:
- By default, most show commands (in any mode) display information for the current context only or, depending on the command syntax, for all contexts. If you are an administrator for the local context, you can insert the optional context ctx-name construct, preceding the show command, to view output for the specified context without entering that context. For more information about using the context ctx-name construct, see the context command description.
- Note:
- By appending a space followed by the pipe ( | ) character at the end of a show command, you can filter the output using a set of modifier keywords and arguments. For more information, see Modifying Output of show Commands in Using the CLI.
1.46.6 Examples
The following example shows how to display active binding information for ports on all line cards:
[local]Redback>show qos port
Slot/Port (vlan-id) PVC Policy-Name Bound L4/L3
lg id 25 foo y Policy7 out
lg id 25 vlan-id 1 y Policy7 in
Policy7 out
lg id 25 vlan-id 2 y Policy7 out
POLICY2 out
lg id 25 vlan-id 4 y Policy7 out
lg id 25 vlan-id 5 y Policy7 out
lg id 25 vlan-id 3 y Policy7 out
lg id 25 vlan-id 3:1 y Policy8 out
lg id 25 vlan-id 3:2 y Policy8 out
lg id 25 vlan-id 3:5 y Policy7 out
lg id 25 vlan-id 3:6 y Policy7 out
lg id 25 vlan-id 3:7 y Policy7 out
lg id 25 vlan-id 3:8 y Policy7 out
lg id 25 vlan-id 3:9 y Policy8 out
Total QoS port policy binding: 15
The following example displays active binding information for ports on a line card in slot 5:
[local]Redback>show qos port slot 5
Slot/Port (vlan-id) PVC Policy-Name Port Qpos L Bound L4/L3
lg id 25 foo y Policy7 1 4 0 out 1
lg id 25 foo y Policy7 2 5 0 out 2
lg id 25 vlan-id 1 y POLICY1 1 in 1
Policy7 1 4 0 out 1
lg id 25 vlan-id 2 y Policy7 1 4 0 out 1
POLICY2 1 out 1
lg id 25 vlan-id 4 y Policy7 1 36 0 out 1
lg id 25 vlan-id 5 y Policy7 1 40 0 out 1
lg id 25 vlan-id 3 y Policy7 1 4 0 out 1
lg id 25 vlan-id 3 y Policy7 2 5 0 out 2
lg id 25 vlan-id 3:1 y Policy8 1 44 0 out 5
lg id 25 vlan-id 3:2 y Policy8 1 48 0 out 6
lg id 25 vlan-id 3:5 y Policy7 1 56 0 out 5
lg id 25 vlan-id 3:6 y Policy7 1 60 0 out 7
lg id 25 vlan-id 3:7 y Policy7 1 64 0 out 8
lg id 25 vlan-id 3:8 y Policy7 1 68 0 out 9
lg id 25 vlan-id 3:9 y Policy8 1 80 0 out 10
1.47 show qos port-map
show qos port-map port-map-name [card-type card-type-name] [detail]
1.47.1 Purpose
Displays information about the configured quality of service (QoS) port group maps for all supported card types.
1.47.2 Command Mode
All modes
1.47.3 Syntax Description
|
port-map-name |
Optional. Name of a QoS port group map for which to display information. If not specified, the information displayed is for all port group maps (of a specified card type, if any). |
|
card-type card-type-name |
Optional. Name of a line card for which QoS port group map information is displayed. If not specified, the information is displayed for all card types. The following are the supported values:
|
|
detail |
Optional. Displays detailed information about the QoS port group maps. |
1.47.4 Default
When entered without any optional syntax, displays brief information about all the configured QoS port group maps.
1.47.5 Usage Guidelines
Use the show qos port-map command to display information about the configured QoS port group maps.
1.47.6 Examples
The following example shows how to display information about all configured QoS port group maps:
[local]Redback>show qos port-map Card Type Map Type Map Name ge3-4-port default tm_max_perf ge3-4-port predef fwd_max_perf ge-10-port default tm_max_perf ge-10-port predef fwd_max_perf ge-20-port default tm_max_perf ge-20-port predef fwd_max_perf fege-60-2-port default tm_fe_perf fege-60-2-port predef tm_max_perf ge4-20-port default tm_max_perf ge4-20-port predef fwd_max_perf ge-5-port default tm_max_perf ge-10-port user-def ge-10-myportmap1 ge-10-port user-def ge-10-myportmap2 fege-60-2-port user-def fe-60-myportmap1 fege-60-2-port user-def fe-60-myportmap2 ge4-20-port user-def ge4-20-myportmap1 ge4-20-port user-def ge4-20-myportmap2
1.48 show qos port-map bind
show qos port-map bind [slot slot-number] [detail]
1.48.1 Purpose
Displays information about the quality of service (QoS) port group map bindings to line cards on the SmartEdge router.
1.48.2 Command Mode
All modes
1.48.3 Syntax Description
|
slot slot-number |
Optional. Chassis slot number of the card for which information about QoS port group map bindings are displayed. The range of values depends on the chassis in which the card is installed. For the SmartEdge 800 1200, and 1200H router, the range of values of the slot-number argument for all supported card types are from 1 to 6 and 9 to 14. For the SmartEdge 600, the range of values are from 1 to 6. For the SmartEdge 400 router, the range of values are from 1 to 4. |
|
slot slot-number |
Optional. Chassis slot number of the card for which information about QoS port group map bindings are displayed. The range of values is from 1 to 6 and 9 to 14. For the SmartEdge 400 router, the range of values are from 1 to 4. |
|
detail |
Optional. Displays detailed information about the QoS port group map binding. |
1.48.4 Default
When entered without any optional syntax, displays brief information about the QoS port group map binding for all cards.
1.48.5 Usage Guidelines
Use the show qos port-map binding command to display information about the QoS port group map binding for all the supported cards that are installed on the SmartEdge router. To display information about the QoS port group map binding for a specific card, use the show qos port-map binding slot command.
1.48.6 Examples
The following example shows how to display information about the QoS port group map bindings for all the cards:
[local]Redback>show qos port-map binding Slot Card Type Status Map Type Map Name 4 Current ge4-20-port locked default tm_max_perf 6 Current ge-10-port unlocked predef fwd_max_perf 10 Current fege-60-2-port unlocked predef tm_max_perf
The following example shows how to display information about the QoS port group map bindings for the card in slot 6:
[local]Redback>show qos port-map binding slot 6 Slot Card Type Status Map Type Map Name 6 Current ge-10-port unlocked predef fwd_max_perf
The following example shows how to display detailed information about the QoS port group map bindings for the card in slot 6:
[local]Redback>show qos port-map binding 6 detail Slot : 6 Current Card Type : ge-10-port (0x7b) Name : fwd_max_perf Type : predef Description : Predefined map optimized for forwarding performance Locked : No Port : 0123456789 Group: 1122334455 Pending Card Type : ge-10-port (0x7b) Name : fwd_max_perf Type : predef Description : Predefined map optimized for forwarding performance
1.49 show qos queue-map
show qos queue-map [map-name]
1.49.1 Purpose
Displays information about one or more configured quality of service (QoS) queue maps.
1.49.2 Command Mode
All modes
1.49.3 Syntax Description
|
map-name |
Optional. Name of a specific QoS queue map. |
1.49.4 Default
When entered without any optional syntax, the show qos queue-map command displays information about all QoS queue maps.
1.49.5 Usage Guidelines
Use the show qos queue-map command to display information about one or more configured QoS queue maps.
Use the map-name argument to display information about a single QoS queue map.
- Note:
- By default, most show commands (in any mode) display information for the current context only or, depending on the command syntax, for all contexts. If you are an administrator for the local context, you can insert the optional context ctx-name construct, preceding the show command, to view output for the specified context without entering that context. For more information about using the context ctx-name construct, see the context command description.
- Note:
- By appending a space followed by the pipe ( | ) character at the end of a show command, you can filter the output using a set of modifier keywords and arguments. For more information, see Modifying Output of show Commands in Using the CLI.
1.49.6 Examples
The following example indicates that the QoS queue map default has 2-queue, 4-queue, and 8-queue mappings:
[local]Redback>show qos queue-map Queue Map-Name Grid Q-2 Q-4 Q-8 default 1 y y y Total QoS queue map: 1
The following example indicates that:
If a QoS policy with 2 queues is configured with the QoS queue map, default, the highest priority traffic (priority 0) is mapped to queue 0, while all other priorities (1 to 7) are mapped to queue 1.
If a QoS policy with 4 queues is configured with the QoS queue map, default, priority 0 traffic is mapped to queue 0, priority 1 and 2 traffic is mapped to queue 1, priorities 2 to 6 are mapped to queue 2, and the lowest priority traffic (priority 7) is mapped to queue 3.
If a QoS policy with 8 queues is configured with the QoS queue map, default, priority 0 traffic is mapped to queue 0, priority 1 traffic is mapped to queue 1, priority 2 traffic is mapped to queue 2, priority 3 traffic is mapped to queue 3, priority 4 traffic is mapped to queue 4, priority 5 traffic is mapped to queue 5, priority 6 traffic is mapped to queue 6, and priority 7 traffic is mapped to queue 7.
[local]Redback>show qos queue-map default Queue Map-Name Grid Q-2 Q-4 Q-8 default 1 y y y Queuing Priority Q-2 Q-4 Q-8 0 0 0 0 1 1 1 1 2 1 1 2 3 1 2 3 4 1 2 4 5 1 2 5 6 1 2 6 7 1 3 7 Total QoS queue map: 1
1.50 show qos username
show qos username subscriber [detail]
1.50.1 Purpose
Displays the quality of service (QoS) circuit information for a given subscriber on the system.
1.50.2 Command Mode
All modes
1.50.3 Syntax Description
|
subscriber |
Fully qualified subscriber name, in the format sub-name@ctx-name, for which circuit information is displayed. |
|
detail |
Optional. Displays details for each subscriber. |
1.50.4 Default
When entered without any optional syntax, displays brief QoS information about the subscriber.
1.50.5 Usage Guidelines
Use the show qos username command to display the QoS circuit information for a given subscriber on the system.
- Note:
- By appending a space followed by the pipe ( | ) character at the end of a show command, you can filter the output using a set of modifier keywords and arguments. For more information, see Modifying Output of show Commands in Using the CLI.
1.50.6 Examples
The following example shows username and subscriber information:
[local]Redback>show qos username dot-v2.2@local Circuit Policy Name Type Rate Source 5/2 vlan-id 2 pppoe 1018 gold pwfq 20000 local meter3 metering 10000 local
The following example shows details about a specific user:
[local]Redback#show qos username dot-v2.2@local detail Circuit: 5/2 vlan-id 2 pppoe 1018 ---------------------------------------------------------- Policy Name : gold Policy Type : pwfq Queue position : 13 Num Queues : 4 Rate : 20000 Rate Source : local Policy Name : meter3 Policy Type : metering Rate : 10000 Rate Source : local Burst : 20000 Excess Burst : 30000
Glossary
| MLPPP bundle |
| The bundle of constituent links that are members of an MLPPP link group. |
| MLPPP |
| Multilink PPP. An extension to PPP that allows a router to use more than one physical link for communication. |
| MP |
| Multilink PPP. |
| PWFQ |
| Priority weighted fair queuing. |