FILE DESCRIPTION     2/198 18-CRA 119 1170/1-V1 Uen B    

Enterprise MIBs

© Ericsson AB 2009–2010. All rights reserved. No part of this document may be reproduced in any form without the written permission of the copyright owner.

Disclaimer

The contents of this document are subject to revision without notice due to continued progress in methodology, design and manufacturing. Ericsson shall have no liability for any error or damage of any kind resulting from the use of this document.

Trademark List

SmartEdge is a registered trademark of Telefonaktiebolaget LM Ericsson.
NetOp is a trademark of Telefonaktiebolaget LM Ericsson.

Contents

1Enterprise MIBs
1.1RBN-AAL5-VCL-STAT-MIB
1.2RBN-X-AAL5-VCL-STAT-MIB
1.3RBN-ATM-CELL-PW-MIB
1.4RBN-ATM-PROFILE-MIB
1.5RBN-ATM-PVC-OAM-MIB
1.6RBN-ATM2-MIB
1.7RBN-BGP-ACCOUNTING-MIB
1.8RBN-BIND-MIB
1.9RBN-BRIDGE-MIB
1.10RBN-BULKSTATS-MIB
1.11RBN-CARDMON-MIB
1.12RBN-CIRCUIT-GROUP-MIB
1.13RBN-CONFIG-FILE-MIB
1.14RBN-CPU-METER-MIB
1.15RBN-DHCP-MIB
1.16RBN-DS1-MIB
1.17RBN-DS3-MIB
1.18RBN-ENVMON-MIB
1.19RBN-FAST-VRRP-MIB
1.20RBN-IP-BIND-MIB
1.21RBN-IPPOOL-MIB
1.22RBN-L2TP-MIB
1.23RBN-L2VPN-MIB
1.24RBN-MEMORY-MIB
1.25RBN-MPLS-L3VPN-STD-EXT-MIB
1.26RBN-NOTIFY-ENHANCE-MIB
1.27RBN-PRODUCT-MIB
1.28RBN-PVC-MIB
1.29RBN-QOS-MIB
1.30RBN-RADIUS-MIB
1.31RBN-SFP-MIB
1.32RBN-SSE-MIB
1.33RBN-STACKEDVLAN-MIB
1.34RBN-SUBSCRIBER-ACTIVE-MIB
1.35RBN-SYS-RESOURCES-MIB
1.36RBN-TACACS-MIB


1   Enterprise MIBs

The SmartEdge router supports several enterprise MIBs. The enterprise Object Identifier (OID) number for the Management Information Base (MIB) hierarchical tree is 2352. So, all enterprise MIB OIDs begin with this syntax: .1.3.6.1.4.1.2352. This document describes each enterprise MIB, the tables in that MIB, and information about objects supported in the MIB, including OIDs for each object. Index objects for each table are identified before each table by the word “index” in bold.

The following sections discuss the enterprise MIBs.

Note:  
Simple Network Management Protocol (SNMP) examples in this document utilize the open-source tool Net-SNMP. Depending on the product you use to monitor your network, the SNMP examples may appear differently from your system.

Note:  
The SmartEdge 100 router does not support all MIBs listed in the tables. Unsupported MIBs are indicated in the Notes column of the table in the About Standard SNMP MIBs section in Standard SNMP MIBs and in the descriptions for the Enterprise MIBs.

Note:  
If you have a support contract, you can download the Enterprise MIBs after you log on at https://ebusiness.ericsson.net.

1.1   RBN-AAL5-VCL-STAT-MIB

Defines objects used to report configuration and performance statistics beyond those reported by standard IETF MIBs for an Asynchronous Transfer Mode (ATM) virtual channel link (VCL).

1.1.1   rbnAtmAal5VclStatTable

Provides a collection of objects providing ATM adaptation layer type 5 (AAL5) configuration and performance statistics of a VCL. This table extends the rbnXAtmAal5VclStatEntry object in RBN-X-AAL5-VCL-STAT-MIB.

Index: ifIndex, atmVclVpi, atmVclVci

Table 1 describes the objects in rbnAtmAal5VclStatTable.

Table 1    Objects in rbnAtmAal5VclStatTable

Object and Object Identifier

Type

Value Range

Description

rbnAtmAal5VclOutDrops


rbnAtmAal5VclStatEntry 1


1.3.6.1.4.1.2352.2.1.1.1.1.1

Counter32

N/A

Number of AAL5 common part convergence sublayer (CPCS) protocol data units (PDUs), transmitted on the AAL5 virtual channel connection (VCC) for the interface specified by ifIndex, that the system dropped, even if the system did not detect errors that prevented PDU transmission. For example, the system might drop a PDU because there was not enough space in the interface output queue. This object is read-only.

1.2   RBN-X-AAL5-VCL-STAT-MIB

Defines objects used to keep track of statistics associated with an ATM VCL.

1.2.1   rbnXAtmAal5VclStatTable

A collection of objects with information about AAL5 configuration and VCL performance statistics.

Index: ifIndex, atmVclVpi, atmVclVci

Table 2 describes the objects in rbnXAtmAal5VclStatTable. All objects in the table are read-only unless otherwise specified.

Table 2    Objects in rbnXAtmAal5VclStatTable

Object and Object Identifier

Type

Value Range

Description

rbnXAtmAal5VclInPkts


rbnXAtmAal5VclStatEntry 1


1.3.6.1.4.1.2352.3.1.1.1.1.1

Counter32

N/A

Number of AAL5 CPCS PDUs received on the AAL5 VCC at the interface identified by the ifIndex object.

rbnXAtmAal5VclOutPkts


rbnXAtmAal5VclStatEntry 2


1.3.6.1.4.1.2352.3.1.1.1.1.2

Counter32

N/A

Number of AAL5 CPCS PDUs transmitted on the AAL5 VCC at the interface identified by the ifIndex object.

rbnXAtmAal5VclInOctets


rbnXAtmAal5VclStatEntry 3


1.3.6.1.4.1.2352.3.1.1.1.1.3

Counter32

N/A

Number of octets contained in AAL5 CPCS PDUs received on the AAL5 VCC at the interface identified by the ifIndex object.

rbnXAtmAal5VclOutOctets


rbnXAtmAal5VclStatEntry 4


1.3.6.1.4.1.2352.3.1.1.1.1.4

Counter32

N/A

Number of octets contained in AAL5 CPCS PDUs transmitted on the AAL5 VCC at the interface identified by the ifIndex object.

1.3   RBN-ATM-CELL-PW-MIB

Defines objects used to retrieve statistics associated with an ATM cell pseudowire circuit.

1.3.1   rbnAtmCellPWStatTable

Contains objects that provide statistics for ATM cell pseudowire circuits used to carry ATM traffic.

Index: rbnAtmCellPWCircuitHandle

Table 3 describes the attributes in rbnAtmCellPWStatTable. All objects in the table are read-only unless otherwise specified.

Table 3    Objects in rbnAtmCellPWStatTable

Object and Object Identifier

Type

Value Range

Description

rbnAtmCellPWOutOfSeqDrops


rbnAtmCellPWStatEntry 2


1.3.6.1.4.1.2352.2.41.1.1.1.2

Counter32

N/A

Total number of cells that dropped because of out-of-sequence PDUs received on the PW circuit.

rbnAtmCellPWCellConcatDrops


rbnAtmCellPWStatEntry 3


1.3.6.1.4.1.2352.2.41.1.1.1.3

Counter32

N/A

Total number of cells that dropped because of cell-concatenated PDUs received on the PW circuit.

1.4   RBN-ATM-PROFILE-MIB

Contains information that helps you manage ATM profiles.

1.4.1   rbnAtmProfileTable

Provides a collection of auxiliary objects providing parameters for ATM profiles.

Index: atmTrafficDescrParamIndex

Table 4 describes the attributes in rbnAtmProfileTable. All objects in the table are read-only unless otherwise specified.

Table 4    Objects in rbnAtmProfileTable

Object and Object Identifier

Type

Value Range

Description

rbnAtmProfileName


rbnAtmProfileEntry 1


1.3.6.1.4.1.2352.2.2.1.1.1.1

AtmProfileName


Octet String

SIZE (0—80)

Text handle assigned to an instance of rbnAtmProfileTable (and through augmentation, atmTrafficDescrParamTable). Using a text handle instead of an arbitrary integer (such as the atmTrafficDescrParamIndex object) allows a configuration to contain human-friendly cross-references to the profiles from those places where they are used, such as in circuit configuration tables. This object is not accessible.

rbnAtmCountersEnabled


rbnAtmProfileEntry 2


1.3.6.1.4.1.2352.2.2.1.1.1.2

TruthValue

1—true


2—false

An indication whether circuits configured with this profile should enable per-circuit statistical counters. An ATM circuit keeps per-circuit statistical counters only if this object is set to true in the profile used by the circuit.

rbnAtmCellLossPriority


rbnAtmProfileEntry 3


1.3.6.1.4.1.2352.2.2.1.1.1.3

TruthValue

1—true


2—false

An indication whether circuits configured with this profile should enable the Cell Loss Priority (CLP) bit on transmitted cells. If the profile used by a circuit has this object set to true, then all cells transmitted on that circuit will have the CLP bit set.

rbnAtmTransmitBuffers


rbnAtmProfileEntry 4


1.3.6.1.4.1.2352.2.2.1.1.1.4

Integer32

1—63

Limit on the total number of outbound transmit packet buffers that may be used by the circuit that references the profile.(1)

(1)  Use this parameter with caution. Setting it improperly can affect overall system performance.


1.5   RBN-ATM-PVC-OAM-MIB

Monitors the ATM operations, administration, and maintenance (OAM) functions.

1.5.1   rbnAtmPvcOamStatusTable

Contains the status of the ATM PVC OAM function for every ATM PVC in the system. One entry in this table exists for each ATM PVC active in the system, whether the PVC is a static or on-demand circuit.

Index: rbnAtmPvcOamStatusSlot, rbnAtmPvcOamStatusPort, rbnAtmPvcOamStatusVpi, rbnAtmPvcOamStatusVci

Table 5 describes the attributes in rbnAtmPvcOamStatusTable. All objects in the table are read-only unless otherwise specified.

Table 5    Objects in rbnAtmPvcOamStatusTable

Object and Object Identifier

Type

Value Range

Description

rbnAtmPvcOamStatusSlot


rbnAtmPvcOamStatusEntry 1


1.3.6.1.4.1.2352.2.19.1.1.1.1

RbnSlot


Unsigned32

0–255

Slot containing the ATM PVC. This object is not accessible.

rbnAtmPvcOamStatusPort


rbnAtmPvcOamStatusEntry 2


1.3.6.1.4.1.2352.2.19.1.1.1.2

RbnSlot


Unsigned32

0–255

Port containing the ATM PVC. This object is not accessible.

rbnAtmPvcOamStatusVpi


rbnAtmPvcOamStatusEntry 3


1.3.6.1.4.1.2352.2.19.1.1.1.3

Integer32

0–4095

VPI value of the ATM PVC. This object is not accessible.

rbnAtmPvcOamStatusVci


rbnAtmPvcOamStatusEntry 4


1.3.6.1.4.1.2352.2.19.1.1.1.4

Integer32

0–65535

VCI value of the ATM PVC. This object is not accessible.

rbnAtmPvcOamStatusState


rbnAtmPvcOamStatusEntry 5


1.3.6.1.4.1.2352.2.19.1.1.1.5

Integer

1—noOam


2—oamUp


3—oamDownLoopback


4—oamDownAis


5—oamDownRdi

State of the ATM PVC OAM function on an ATM PVC.


The noOam value indicates the ATM PVC OAM function is not active on the ATM PVC.


The oamUp value indicates the ATM PVC OAM function is active on the ATM PVC, and no failure condition is currently detected on the circuit.


The oamDownLoopback value indicates the ATM PVC OAM function is active on the ATM PVC, and F5 OAM loopback cell management has detected a fault on the circuit.


The oamDownAis value indicates the ATM PVC OAM function is active on the ATM PVC, and a VC-AIS cell was recently received, which indicates a fault on the circuit.


The oamDownRdi value indicates the ATM PVC OAM function is active on the ATM PVC, and a VC-RDI cell was recently received, which indicates a fault on the circuit.

1.6   RBN-ATM2-MIB

Monitors statistics associated with ATM VPL and VCL beyond those instrumented by ATM2-MIB.

1.6.1   rbnAtm2VplStatTable

Provides a collection of statistics objects of a VPL.

Index: ifIndex, atmVplVpi

Table 6 describes the attributes in rbnAtm2VplStatTable. All objects in the table are read-only unless otherwise specified.

Table 6    Objects in rbnAtm2VplStatTable

Object and Object Identifier

Type

Value Range

Description

rbnAtm2VplOutPktDrops


rbnAtm2VplStatEntry 1


Counter32

0—4294967295

The number of transmit packets dropped by this VPL.

1.6.2   rbnAtm2VclStatTable

Provides a collection of statistics objects of a VCL.

Index: ifIndex, atmVclVpi, atmVclVci

Table 7 describes the attributes in rbnAtm2VclStatTable. All objects in the table are read-only unless otherwise specified.

Table 7    Objects in rbnAtm2VclStatTable

Object and Object Identifier

Type

Value Range

Description

rbnAtm2VclOutPktDrops


rbnAtm2VclStatEntry 1


Counter32

0—4294967295

The number of transmit packets dropped by this VCL.

1.6.3   rbnAtm2Aal5VclStatTable

This table provides a collection of auxiliary objects providing AAL5 configuration and performance statistics of a VCL.

Index: ifIndex, atmVclVpi, atmVclVci

Table 8 describes the attributes in rbnAtm2Aal5VclStatTable. All objects in the table are read-only unless otherwise specified.

Table 8    Objects in rbnAtm2Aal5VclStatTable

Object and Object Identifier

Type

Value Range

Description

rbnAtm2Aal5VclOutPktDrops


rbnAtm2Aal5VclStatEntry 1


Counter32

0—4294967295

The number of AAL5 CPCS PDUs received for transmission on the AAL5 VCC at the interface are identified by the ifIndex. These PDUs are chosen to be dropped to prevent their being transmitted even though no errors had been detected. A lack of space on the interface output queue can cause PDUs to be dropped.

1.7   RBN-BGP-ACCOUNTING-MIB

Defines objects to account for IP traffic differentially using BGP policies. RBN-BGP-ACCOUNTING-MIB works only when the snmp server enhance ifmib command (in global configuration mode) is enabled.

1.7.1   rbnBpaTable

A list of BGP policy accounting entries. An entry contains statistics applicable to a BGP-based routing policy set on an interface. The ifIndex object values in Table 9 represent a port, channel, subchannel, or circuit layer that supports the IF-MIB ifPacketGroup object, ifHCPacketGroup object, or ifVHCPacketGroup object, and is bound to an IP interface for which BGP policy-based accounting is enabled. Because the IF-MIB may provide support for a subset of the physical interfaces available on the system, that support for BGP policy-based accounting information in this MIB is limited to the same subset of physical interfaces supported in the IF-MIB.

Index: ifIndex, rbnBpaBucketIndex

Table 9 describes the rbnBpaTable. All objects in the table are read-only unless otherwise specified.

Table 9    Objects in rbnBpaTable

Object and Object Identifier

Type

Value Range

Description

rbnBpaBucketIndex


rbnBpaEntry 1


1.3.6.1.4.1.2352.2.20.1.1.1.1

Integer32

1–2147483647

Integer greater than 0 that uniquely identifies a BGP routing policy set on this interface.

rbnBpaInPacketCount


rbnBpaEntry 2


1.3.6.1.4.1.2352.2.20.1.1.1.2

Counter64

N/A

Total number of packets received for a particular BGP routing policy on an interface.

rbnBpaInOctetCount


rbnBpaEntry 3


1.3.6.1.4.1.2352.2.20.1.1.1.3

Counter64

N/A

Total number of octets received for a particular BGP routing policy on an interface.

rbnBpaCircuitDescr


rbnBpaEntry 4


1.3.6.1.4.1.2352.2.20.1.1.1.4

SnmpAdminString

SIZE (0–192)

Descriptive version of the interface that is consistent with information displayed in the CLI. This string is formatted as slot/port:channel:subchannel authority/level/index. The channel and subchannel are only included when appropriate; for example, 4/1 1/2/7, 4/1:1 1/2/7 or 4/1:1:1 1/2/7. If a circuit description is not available, this object contains a zero-length string.

rbnBpaInterfaceName


rbnBpaEntry 5


1.3.6.1.4.1.2352.2.20.1.1.1.5

SnmpAdminString

SIZE (0–127)

Name of the IP interface bound to a circuit. If the IP interface name is not available, this object contains a zero-length string.

rbnBpaContextName


rbnBpaEntry 6


1.3.6.1.4.1.2352.2.20.1.1.1.6

SnmpAdminString

SIZE (0–63)

Name of context in which this IP interface is defined. If context information is not available, this object contains a zero-length string.

1.8   RBN-BIND-MIB

Defines the objects for used to support the configuration and management of circuit bindings.

1.8.1   rbnBindTable

This table contains the objects that identify and configure circuit bindings. Rows in this table are created or deleted when a circuit is created or deleted. No explicit creation or deletion of rows is allowed or required.

Index: rbnBindCircuit

Table 10 describes the attributes in rbnBindTable. All objects in the table are read-only unless otherwise specified.

Table 10    Objects in rbnBindTable

Object and Object Identifier

Type

Value Range

Description

rbnBindType


rbnBindEntry 2


1.3.6.1.4.1.2352.2.17.1.1.1.2

RbnBindType

1—unbound


2—authBind


3—bypassBind


4—interfaceBind


5—subscriberBind


6—l2tptunnelBind


7—sessionBind


8—dot1qBind


9—multiIntfBind


10—multiSubBind


11—multiClipsBind

Type of the binding. The bind type must be appropriate to the type of circuit that it is being applied to.


When a circuit is created, an initial binding is established with the unbound type.


If you change the bind type for a circuit, the previous binding is removed and active sessions are dropped. If an existing binding on the circuit is the same as the new binding, the existing binding is not removed. When changing the bind type to a new bind type, all objects mandatory for the new bind type must be included in the set operation.


The bind type determines which group of objects in a row of rbnBindTable apply for that instance of a circuit.

rbnBindName


rbnBindEntry 3


1.3.6.1.4.1.2352.2.17.1.1.1.3

SnmpAdminString

SIZE (1–192)

A name associated with the binding. This field is only applicable when the value of the rbnBindType object is:


  • bypassBind

  • interfaceBind

  • subscriberBind

  • l2tptunnelBind

  • multiIntfBind

  • multiSubBind

  • sessionBind

rbnBindPassword


rbnBindEntry 4


1.3.6.1.4.1.2352.2.17.1.1.1.4

SnmpAdminString

SIZE (1–64)

The AAA password. This field is only applicable when the value of the rbnBindType object is subscriberBind. If the value of the rbnBindType object is not this bind type, the rbnBindPassword object is not instantiated for this entry.

rbnBindContext


rbnBindEntry 5


1.3.6.1.4.1.2352.2.17.1.1.1.5

SnmpAdminString

SIZE (1–64)

The name of the context associated with the binding. This field is applicable only when one of the following rbnBindType values is specified:


  • bypassBind

  • interfaceBind

  • subscriberBind

  • l2tptunnelBind

  • multiIntfBind

  • multiSubBind

  • sessionBind

  • multiClipsBind


If the value of the rbnBindType object is not one of these bind types, the rbnBindContext object is not instantiated for this entry.

rbnBindAuthContext


rbnBindEntry 6


1.3.6.1.4.1.2352.2.17.1.1.1.6

SnmpAdminString

SIZE (1–64)

The name of the authentication context associated with the binding. This object is the name of the context to which PPP sessions on the circuits being bound are restricted.


Specification of this column is optional.


When using this optional context name, all attempts to bind PPP sessions to contexts other than the one specified fail.


This object is applicable only when one of the following rbnBindType values is specified:


  • authBind

  • multiIntfBind

  • multiSubBind


If the value of the rbnBindType object is not one of these bind types, the rbnBindAuthContext object is not instantiated for this entry.

rbnBindServiceGrp


rbnBindEntry 7


1.3.6.1.4.1.2352.2.17.1.1.1.7

SnmpAdminString

SIZE (1–64)

The name of the service access list associated with the binding. This object is the name of the service access list that defines the services available to the PPP-encapsulated circuit.


Specification of this column is optional.


When using this optional service access list, all attempts to authenticate to contexts or domains not permitted by the named service access list fail.


This object is applicable only when one of the following rbnBindType values is specified:


  • authBind

  • multiIntfBind

  • multiSubBind

  • multiClipsBind


If the value of the rbnBindType object is not one of these bind types, the rbnBindServiceGrp object is not instantiated for this entry.

rbnBindAcl


rbnBindEntry 8


1.3.6.1.4.1.2352.2.17.1.1.1.8

SnmpAdminString

SIZE (1–64)

Name of the bridge access control list associated with the binding. This object is the name of the Access control list to be applied to the session. The access control list must already have been configured in the context of the session peer. This is typically used to filter packets so that only PPPoE traffic is allowed through an Ethernet L2TP tunnel.


Specification of this column for a given entry is optional. This object is applicable only when the sessionBind rbnBindType value is specified.


If the value of the rbnBindType object is not sessionBind, the rbnBindAcl object is not instantiated for this entry.

rbnBindAuthChap


rbnBindEntry 9


1.3.6.1.4.1.2352.2.17.1.1.1.9

TruthValue

1—true


2—false

If the value of this object is true, the PPP authentication protocol to be used is Challenge Handshake Authentication Protocol.


This object is applicable only when one of the following rbnBindType values is specified:


  • authBind

  • multiIntfBind

  • multiSubBind


If the value of the rbnBindType object is not one of these bind types, the rbnBindAuthChap object is not instantiated for this entry.


When performing a set operation on a row that involves one of these bind types, either the rbnBindAuthChap object or rbnBindAuthPap object or both must be specified.


If both the rbnBindAuthChap object and rbnBindAuthPap object are true, then either authentication protocol can be used.

rbnBindAuthPap


rbnBindEntry 10


1.3.6.1.4.1.2352.2.17.1.1.1.10

TruthValue

1—true


2—false

If the value of this object is true, the PPP authentication protocol to be used is Password Authentication Protocol.


This object is applicable only when one of the following rbnBindType values is specified:


  • authBind

  • multiIntfBind

  • multiSubBind


If the value of the rbnBindType object is not one of these bind types, then the rbnBindAuthPap object is not instantiated for this entry.


When performing a set operation on a row that involves one of these bind types, either the rbnBindAuthChap object or the rbnBindAuthPap object or both must be specified.


If both the rbnBindAuthChap object and the rbnBindAuthPap object are true, then either authentication protocol can be used.

rbnBindAuthWait


rbnBindEntry 11


1.3.6.1.4.1.2352.2.17.1.1.1.11

TruthValue

1—true


2—false

If the value of this object is true, the inbound CHAP authentication is completed first. That is, after the two sides have decided to use CHAP, the SMS waits for the inbound side to initiate authentication.


If the value is true, the rbnBindAuthChap object must also be specified.


This object is applicable only when one of the following rbnBindType values is specified:


  • authBind

  • multiIntfBind

  • multiSubBind


If the value of the rbnBindType object is not one of these bind types, then the rbnBindAuthWait object is not instantiated for this entry.


When performing a set operation on a row that involves this bind type, specification of this column is optional.


If not specified, this object is not instantiated.

rbnBindAuthPapFirst


rbnBindEntry 12


1.3.6.1.4.1.2352.2.17.1.1.1.12

TruthValue

1—true


2—false

If the value of this object is true, PAP is negotiated before CHAP. If the value of this object is false, then CHAP is negotiated before PAP.


With SNMP get operations, both the rbnBindAuthChap object and the rbnBindAuthPap object must be true, or this object is not instantiated.


With SNMP set operations, if the value of this object is true, then both the rbnBindAuthChap object and the rbnBindAuthPap object must also be specified as 'true'.


This object is applicable only when one of the following rbnBindType values is specified:


  • authBind

  • multiIntfBind

  • multiSubBind


If the value of the rbnBindType object is not one of these bind types, then the rbnBindAuthPapFirst object is not instantiated for this entry.


When performing a set operation on a row that involves one of these bind types, specification of this column is optional.


If not specified, this object is not instantiated.

rbnBindMaxSessions


rbnBindEntry 13


1.3.6.1.4.1.2352.2.17.1.1.1.13

Unsigned32

1–65535

The maximum number of concurrent sessions allowed on the circuit; applicable only to circuits that have an encapsulation of type PPPoE. If the circuit is not of this type, then this entry is ignored.


Specification of this column is optional.


If not specified, this object is not instantiated.


This object is applicable only when one of the following rbnBindType values is specified:


  • authBind

  • sessionBind

  • multiIntfBind

  • multiSubBind

  • multiClipsBind


If the value of the rbnBindType object is not one of these bind types, the rbnBindMaxSessions object is not instantiated for this entry.


The maximum number of concurrent sessions allowed on the circuit depends on the platform, as specified in the following example:


Platform   Sessions     MemSize
-------------------------------
SMS10000       65535 
SMS1800/1000   10000    64MB FE
SMS1800/1000    8000    48MB FE
SMS1800/1000    4000    32MB FE
SMS1800/1000    4000    16MB FE
SMS1800/1000    4000    8MB FE 
SMS500          2000 

rbnBindvcSlot


rbnBindEntry 14


1.3.6.1.4.1.2352.2.17.1.1.1.14

RbnSlot


Unsigned32

(0–255)

Chassis slot number associated with this binding.


Use the 'dot1qBind' type for binding an ATM or Frame Relay PVC to an Ethernet port using the specified VLAN ID in the rbnBindVpn object.


This object is applicable only when the rbnBindType values is dot1qBind.


If the value of the rbnBindType object is not one of these bind types, then the rbnBindPvcSlot object is not instantiated for this entry.

rbnBindPvcPort


rbnBindEntry 15


1.3.6.1.4.1.2352.2.17.1.1.1.15

RbnPort


Unsigned32

0–255

Chassis port number associated with this binding.


Use the 'dot1qBind' type for binding an ATM or Frame Relay PVC to an Ethernet port using the specified VLAN ID in the rbnBindVpn object.


This object is applicable only when the rbnBindType value is dot1qBind.


If the value of the rbnBindType object is not do1qBind, the rbnBindPvcPort object is not instantiated for this entry.

rbnBindVpn


rbnBindEntry 16


1.3.6.1.4.1.2352.2.17.1.1.1.16

Unsigned32

2–4094

The specific tag to which the PVC is mapped on the specified Ethernet port.


Use the 'dot1qBind' type for binding an ATM or Frame Relay PVC to an Ethernet port using the specified VLAN ID in the rbnBindVpn object.


This object is applicable only when the rbnBindType value is dot1qBind.


If the value of the rbnBindType object is not dot1qBind, the rbnBindVpn object is not instantiated for this entry.

rbnBindAuthDhcp


rbnBindEntry 17


1.3.6.1.4.1.2352.2.17.1.1.1.17

TruthValue

1—true


2—false

If 'true', specifies an authentication mechanism where the DHCP server makes a request to the authentication subsystem on receipt of incoming DHCP discover packets.


This object is applicable only when one of the following rbnBindType values is specified:


  • multiIntfBind

  • multiClipsBind


If the value of the rbnBindType object is not one of these bind types, then the rbnBindAuthDhcp object is not instantiated for this entry.


When performing a set operation on a row that involves one of these bind types, if either the rbnBindAuthChap object or the rbnBindAuthPap object or both are specified, the rbnBindAuthDhcp object can not be specified. This object is read-create.

1.9   RBN-BRIDGE-MIB

Provides notification when a bridging loop has been detected.

To return information about a specific instance of a bridge in a context, you can use the following syntax during a MIB walk:

community_string@bridge name@context name

The following sections contain object information for RBN-BRIDGE-MIB.

1.9.1   RBN-BRIDGE-MIB Objects

Table 11 describes objects in RBN-BRIDGE-MIB. All objects in the table are read-only unless otherwise specified.

Table 11    Objects in RBN-BRIDGE-MIB

Object and Object Identifier

Type

Value Range

Description

rbnBridgeNotifyEnable


rbnBridgeNotify 1


1.3.6.1.4.1.2352.2.42.1.1.1

TruthValue

1—true


2—false

This object provides a mechanism for enabling and disabling bridge circuit state notifications. A value of true indicates that bridge circuit state notifications are enabled. A value of false indicates that bridge circuit state notifications are disabled. This object is read-write.

rbnBridgeGroupName


rbnBridgeNotify 2


1.3.6.1.4.1.2352.2.42.1.1.2

SnmpAdminString

SIZE (1–32)

Identifier for the bridge instance. This object is accessible-for-notify.

rbnBridgeCircuitDescriptor


rbnBridgeNotify 3


1.3.6.1.4.1.2352.2.42.1.1.3

SnmpAdminString

SIZE (1–255)

A descriptor for identifying the bridge circuit. This object is accessible-for-notify.

rbnBridgeCircuitStatus


rbnBridgeNotify 4


1.3.6.1.4.1.2352.2.42.1.1.4

Integer

1—blocked


2—cleared

The status of the circuit in the bridge if it is blocked or cleared based on loop detection. This object is accessible-for-notify.

rbnBridgeGroupContextName


rbnBridgeNotify 5


1.3.6.1.4.1.2352.2.42.1.1.5

SnmpAdminString

SIZE (1–64)

The context in which the circuit is defined. This object is accessible-for-notify.

rbnBridgePortPreviousState


rbnBridgeNotify 6


1.3.6.1.4.1.2352.2.42.1.1.6

Integer

1—deleted


2—disabled


3—blocked


4—listening


5—learning


6—forwarding

The state of the bridge port.

1.9.2   rbnBridgeIdTable

This table contains the bridge identifier.

Index: rbnBridgeName

Table 12 describes the attributes in rbnBridgeIdTable. All objects in the table are read-only unless otherwise specified.

Table 12    Objects in rbnBridgeIdTable

Object and Object Identifier

Type

Value Range

Description

rbnBridgeName


rbnBridgeIdEntry 1


1.3.6.1.4.1.2352.2.42.1.2.1.1.1

SnmpAdminString

SIZE (1–32)

The bridge name. This object is not accessible.

rbnBridgeId


rbnBridgeIdEntry 2


1.3.6.1.4.1.2352.2.42.1.2.1.1.2

Integer32

1– 65535

The bridge identifier referring to this bridge. This object is read-only.

1.9.3   rbnBridgePortCctDescrTable

This table contains a bridge port number and its circuit description.

Index: dot1dBasePort

Table 13 describes the object in rbnBridgePortCctDescrTable. All objects in the table are read-only unless otherwise specified.

Table 13    Objects in rbnBridgePortCctDescrTable

Object and Object Identifier

Type

Value Range

Description

rbnBridgePortCctDescr


rbnBridgePortCctDescrEntry 1


1.3.6.1.4.1.2352.2.42.1.2.2.1.1

SnmpAdminString

SIZE (0–64)

The circuit description of this bridge port.

1.10   RBN-BULKSTATS-MIB

Manages bulk-statistics-gathering functions on SmartEdge router.

The following sections contain information for RBN-BULKSTATS-MIB.

1.10.1   RBN-BULKSTATS-MIB Objects

Table 14 describes the objects for RBN-BULKSTATS-MIB. All objects in the table are read-only unless otherwise specified.

Table 14    Objects for RBN-BULKSTATS-MIB

Object and Object Identifier

Type

Value Range

Description

rbnBulkStatsLastTrfrIpAddrType


rbnBulkStatsLastTrfr 1


1.3.6.1.4.1.2352.2.21.1.1.1

InetAddressType


Integer

0—unknown


1—ipv4


2—ipv6


16—dns

The address type contained in the rbnBulkStatsLastTrfrIpAddr object.

rbnBulkStatsLastTrfrIpAddr


rbnBulkStatsLastTrfr 2


1.3.6.1.4.1.2352.2.21.1.1.2

InetAddress


String

SIZE (0–255)

The IP Address of the receiver station to which transfer of bulk statistics data was last attempted.


If the IP address type is unknown, or if no transfers have occurred, a zero-length string is returned.

rbnBulkStatsLastTrfrStatus


rbnBulkStatsLastTrfr 3


1.3.6.1.4.1.2352.2.21.1.1.3

Integer

1—none


2—success


3—genError


4—loginFailed


5—badFilename


6—remoteHostFailed


7—other

The status of the last bulk statistics data transfer.

1.10.2   rbnBulkStatsLastTrfrTable

Monitors the last attempted transfer of the bulk statistics data for each bulkstats policy. All rows in this table are accessible when the context 'local' is specified in the SNMP message. SNMP requests using other contexts return only the row that matches the context.

Index: vacmContextName, rbnBulkStatsLastTrfrPolicy

Table 15 describes the attributes in rbnBulkStatsLastTrfrTable. All objects in the table are read-only unless otherwise specified.

Table 15    Objects in rbnBulkStatsLastTrfrTable

Object and Object Identifier

Type

Value Range

Description

rbnBulkStatsLastTrfrIpAddrType2


rbnBulkStatsLastTrfrEntry 2


1.3.6.1.4.1.2352.2.21.1.1.4.1.2

InetAddressType


Integer

0—unknown


1—ipv4


2—ipv6


‘6—dns

The address type contained in the rbnBulkStatsLastTrfrIpAddr2 object.

rbnBulkStatsLastTrfrIpAddr2


rbnBulkStatsLastTrfrEntry 3


1.3.6.1.4.1.2352.2.21.1.1.4.1.3

InetAddress


String

SIZE (0–255)

The IP Address of the receiver station to which transfer of bulk statistics data was last attempted.


If the IP address type is unknown, or if no transfers have occured, a zero-length string is returned.

rbnBulkStatsLastTrfrStatus2


rbnBulkStatsLastTrfrEntry 4


1.3.6.1.4.1.2352.2.21.1.1.4.1.4

Integer

1—none


2—success


3—genError


4—loginFailed


5—badFilename


6—remoteHostFailed


7—other

The status of the last bulk statistics data transfer. This object is read-only.

1.11   RBN-CARDMON-MIB

Manages the controller, alarm, and traffic card alarm functions. For a list of controller and traffic card alarms supported by this MIB, see the MIBs capability file.

The following sections contain object information for RBN-CARDMON-MIB.

1.11.1   rbnCardAlarmActiveTable

Contains the card alarms currently active on the system.

Index: rbnCardAlarmSlot, rbnCardAlarmActiveIndex

Table 16 describes the attributes in rbnCardAlarmActiveTable. All objects in the table are read-only unless otherwise specified.

Table 16    Objects in rbnCardAlarmActiveTable

Object and Object Identifier

Type

Value Range

Description

rbnCardAlarmId


rbnCardAlarmActiveEntry 3


1.3.6.1.4.1.2352.2.31.1.1.1.3

RbnAlarmId


Integer

1—unknown


2—cpFail


3—cpBackplaneFail


4—diagFail


5—voltageFail


6—controllerSwitchFail


7—controllerTempCritical


8—controllerFail


9—controllerDiagFail


10—cpPowerOnDiagFail


11—controllerPowerOnDiagFail


12—cpOverheat


13—controllerOverheat


14—backplaneclkfail


15—btciferror


16—btcnotready


17—cpbackplanedegrade


18—cpcardcodemismatch


19—cpmismatch


20—cpmissing


21—cpresetcomplete


22—downloadcompleted


23— downloadfailed


24—syncfail


25—backupfail


26—controllercardcodemismatch


27— controllercardtypemismatch


28—controllermissing


29—controlleroverheat


30—controllerswitchauto


31—controllerswitchcompleted


32—controllerswitchexfailed


33—controllerswitchforced


34—controllerswitchmanual


35—localfantrayinventfail


36—localinventfail


37—localbackplaneinventfail


38—lostm2m


39—nonvolatilememfail


40—peerhwincompatible


41—peerinventfail


42—peermodeincompatible

An identifier for the alarm.

rbnCardAlarmType


rbnCardAlarmActiveEntry 4


1.3.6.1.4.1.2352.2.31.1.1.1.4

RbnAlarmType


Integer

43—peersharedformatmismatch


44—rtclockfail


45—mic1missing


46—mic2missing


47—mic1mismatch


48—mic2mismatch


49—mic1voltagefailure


50—mic2voltagefailure


51—mic1overheat


52—mic2overheat


53—mic1failure


54—mic2failure


55—mic1podfail


56—mic2podfail


57—mic1diagnosticfail


58—mic2diagnosticfail


59—ethtransceiverrxpowerhi


60—ethtransceiverrxpowerlo


61—ethtransceivertemphi


62—ethtransceivertemplo


63—ethtranceivervoltagehi


64—ethtranceivervoltagelo


65—ethtransceiverbiashi


66—ethtransceiverbiaslo


67—ethtransceivertxpowerhi


68—ethtransceivertxpowerlo


69—ethtransceiveraux1hi


70—ethtransceiveraux1lo


71—ethtransceiveraux2hi


72—ethtransceiveraux2lo


73—ethtransceiverlvcc5hi


74—ethtransceiverlvcc5lo


75—ethtransceiverlvcc3hi


76—ethtransceiverlvcc3lo


77—ethtransceiverlvcc2hi


78—ethtransceiverlvcc2lo

The type of the alarm.

rbnCardAlarmDateAndTime


rbnCardAlarmActiveEntry 5


1.3.6.1.4.1.2352.2.31.1.1.1.5

DateAndTime

N/A

The local date and time when the alarm was raised.

rbnCardAlarmDescription


rbnCardAlarmActiveEntry 6


1.3.6.1.4.1.2352.2.31.1.1.1.6

SnmpAdmin String

SIZE (0–64)

A text string that conveys additional information about the alarm.

rbnCardAlarmProbableCause


rbnCardAlarmActiveEntry 7


1.3.6.1.4.1.2352.2.31.1.1.1.7

RbnAlarm ProbableCause


Integer

1—aIS


3—degradedSignal


4—farEndReceiverFailure


5—framingError


6—lossOfFrame


7—lossOfPointer


8—lossOfSignal


9—payloadTypeMismatch


10- transmissionError


12—excessiveBER


13—pathTraceMismatch


14—unavailable


15—signalLableMismatch


17—receiveFailure


18—transmitFailure


19—modulationFailure


20—demodulationFailure


21—linkFailure


22—configurationMismatch


23—concatenationMismatch


51—pbackplaneFailure


53—equipmentIdDuplication


54—externalIFDeviceProblem


55—lineCardProblem


56—multiplexerProblem


57—nEIdentifierDuplication


58—powerProblem


59—processorProblem


60—protectionPathFailure


61—receiverFailure


62—replaceableUnitMissing


63—replaceableUnitTypeMismatch

The probable cause for this alarm.

rbnCardAlarmProbableCause


rbnCardAlarmActiveEntry 7


1.3.6.1.4.1.2352.2.31.1.1.1.7

 

64—syncSourceMismatch


65—terminalProblem


66—timingProblem


67—transmitterFailure


68—trunkCardProblem


69—replaceableUnitProblem


70—realTimeClockFailure


101—airCompressorFailure


102—airConditioningFailure


103—airDryerFailure


104—batteryDischarging


106—commercialPowerFailure


107—coolingFanFailure


108—engineFailure


109—fireDetectorFailure


110—fuseFailure


111—generatorFailure


112—lowBatteryThreshold


113—pumpFailure


114—rectifierFailure


115—rectifierHighVoltage


116—rectifierLowVoltage


117—ventilationsSystemFailure


118—enclosureDoorOpen


119—explosiveGas


120—fire


121—flood


122—highHumidity


123—highTemperature


124—highWind


125—iceBuildUp


126—intrusionDetection


127—lowFuel


128—lowHumidity

 

rbnCardAlarmProbableCause


rbnCardAlarmActiveEntry 7


1.3.6.1.4.1.2352.2.31.1.1.1.7

 

129—lowCablePressure


130—lowTemperature


131—lowWater


132—smoke


133—toxicGas


149—customized


151—storageCapacityProblem


152—memoryMismatch


153—corruptData


154—outOfCPUCycles


155—sfwrEnvironmentProblem


156—sfwrDownloadFailure


157—lossOfRealTime


158—reinitialized


159—operationNotification


160—operationFailure


1001—lossOfTimingSource


1002—apsChannelProcessingFailure


1003—apsByteFailure


1004—apsChannelMatchFailure


1005—apsModeMismatch


1007—lossOfTUMultiframeIndicator


1010—pathSelectorFailure


1011—blsrDefaultKBytes


1012—blsrInconsistentAPSCodes


1013—blsrNodeIdMismatch


1014—blsrImproperAPSCodes


1015—blsrSquelching


1016—blsrInvalidNeighbour


1017—blsrInvalidRingMap


1018—blsrInvalidRingId


1019—blsrIncompleteRingConfig


1020—blsrIncompleteETConfig


1021—blsrNodeIncorrectOrientation

 

rbnCardAlarmSeverity


rbnCardAlarmActiveEntry 8


1.3.6.1.4.1.2352.2.31.1.1.1.8

RbnAlarmPerceivedSeverity


Integer

1—cleared


2—critical


3—major


4—minor


5—warning

The perceived severity of the alarm.

rbnCardAlarmServiceAffecting


rbnCardAlarmActiveEntry 9


1.3.6.1.4.1.2352.2.31.1.1.1.9

RbnAlarmServiceAffecting


Integer

1—yes


2—no

Indicates whether the alarm is perceived to impact service.

1.11.2   rbnCardStatsTable

Contains statistics for each traffic card. This table also provides an entry for the card that contains the Ethernet management port.

Index: rbnCardStatsSlot

Table 17 describes the attributes in rbnCardStatsTable.

Table 17    Objects in rbnCardStatsTable

Object and Object Identifier

Type

Value Range

Description

rbnCardStatsTotalCircuits


rbnCardStatsEntry 2


1.3.6.1.4.1.2352.2.31.1.2.1.2

Gauge32

N/A

Count of all circuits configured on the card.

rbnCardStatsUpCircuits


rbnCardStatsEntry 3


1.3.6.1.4.1.2352.2.31.1.2.1.3

Gauge32

N/A

Count of circuits in an up state configured on the card.

rbnCardStatsDownCircuits


rbnCardStatsEntry 4


1.3.6.1.4.1.2352.2.31.1.2.1.4

Gauge32

N/A

Count of circuits in a down state configured on the card.

rbnCardStatsUnboundCircuits


rbnCardStatsEntry 5


1.3.6.1.4.1.2352.2.31.1.2.1.5

Gauge32

N/A

Count of circuits not bound to an interface that are configured on the card.

rbnCardStatsNoBindCircuits


rbnCardStatsEntry 6


1.3.6.1.4.1.2352.2.31.1.2.1.6

Gauge32

N/A

Count of circuits configured on the card that are not bound to an interface and are not subscriber or CLIPS circuits.

rbnCardStatsBindTotalCircuits


rbnCardStatsEntry 7


1.3.6.1.4.1.2352.2.31.1.2.1.7

Gauge32

N/A

Count of all circuits bound to an interface that are configured on the card.

rbnCardStatsBindIfCircuits


rbnCardStatsEntry 8


1.3.6.1.4.1.2352.2.31.1.2.1.8

Gauge32

N/A

Count of circuits configured on the card that are bound to an interface and are not subscriber circuits.

rbnCardStatsBindAuthCircuits


rbnCardStatsEntry 9


1.3.6.1.4.1.2352.2.31.1.2.1.9

Gauge32

N/A

Count of subscriber and CLIPS bind authentication circuits configured on the card.

rbnCardStatsBindSubCircuits


rbnCardStatsEntry 10


1.3.6.1.4.1.2352.2.31.1.2.1.10

Gauge32

N/A

Count of bind subscriber, including CLIPS, and bind auto-subscriber circuits configured on the card.

rbnCardStatsAtmCircuits


rbnCardStatsEntry 11


1.3.6.1.4.1.2352.2.31.1.2.1.11

Gauge32

N/A

Count of ATM circuits configured on the card.

rbnCardStatsEthCircuits


rbnCardStatsEntry 12


1.3.6.1.4.1.2352.2.31.1.2.1.12

Gauge32

N/A

Count of Ethernet circuits configured on the card.

rbnCardStatsPppCircuits


rbnCardStatsEntry 13


1.3.6.1.4.1.2352.2.31.1.2.1.13

Gauge32

N/A

Count of PPP circuits configured on the card.

rbnCardStatsPppoeCircuits


rbnCardStatsEntry 14


1.3.6.1.4.1.2352.2.31.1.2.1.14

Gauge32

N/A

Count of PPPoE circuits configured on the card.

rbnCardStatsDot1qCircuits


rbnCardStatsEntry 15


1.3.6.1.4.1.2352.2.31.1.2.1.15

Gauge32

N/A

Count of 802.1Q circuits configured on the card.

rbnCardStatsFrCircuits


rbnCardStatsEntry 16


1.3.6.1.4.1.2352.2.31.1.2.1.16

Gauge32

N/A

Count of Frame Relay circuits configured on the card.

rbnCardStatsChdlcCircuits


rbnCardStatsEntry 17


1.3.6.1.4.1.2352.2.31.1.2.1.17

Gauge32

N/A

Count of Cisco HDLC circuits configured on the card.

rbnCardStatsGreCircuits


rbnCardStatsEntry 18


1.3.6.1.4.1.2352.2.31.1.2.1.18

Gauge32

N/A

Count of GRE circuits configured on the card.

rbnCardStatsMplsCircuits


rbnCardStatsEntry 19


1.3.6.1.4.1.2352.2.31.1.2.1.19

Gauge32

N/A

Count of MPLS circuits configured on the card.

rbnCardStatsClipsCircuits


rbnCardStatsEntry 20


1.3.6.1.4.1.2352.2.31.1.2.1.20

Gauge32

N/A

Count of CLIPS circuits configured on the card.

rbnCardStatsVplsCircuits


rbnCardStatsEntry 21


1.3.6.1.4.1.2352.2.31.1.2.1.21

Gauge32

N/A

Count of VPLS circuits configured on the card.

rbnCardStatsIpipCircuits


rbnCardStatsEntry 22


1.3.6.1.4.1.2352.2.31.1.2.1.22

Gauge32

N/A

Count of IP-in-IP tunnel circuits configured on the card.

rbnCardStatsIpv6v4ManualCircuits


rbnCardStatsEntry 23


1.3.6.1.4.1.2352.2.31.1.2.1.23

Gauge32

N/A

Count of IPv6v4-manual tunnel circuits configured on the card.

rbnCardStatsIpv6v4AutoCircuits


rbnCardStatsEntry 24


1.3.6.1.4.1.2352.2.31.1.2.1.24

Gauge32

N/A

Count of IPv6v4-auto tunnel circuits configured on the card.

1.11.3   Example

You can use the RBN-CARDMON-MIB to obtain the 802.1q PVC tunnel circuit count for each slot for trending analysis. The rbnCardStatsTable is indexed by slot number.

The following example gets a slot-level count for a specific circuit type:

sh-3.00$ snmpbulkwalk -v2c -cpublic -m RBN-CARDMON-MIB SE-lab2 rbnCardStatsDot1qCircuits

RBN-CARDMON-MIB::rbnCardStatsDot1qCircuits.7 = Gauge32: 0

RBN-CARDMON-MIB::rbnCardStatsDot1qCircuits.11 = Gauge32: 2

Use the following CLI to view the information for a circuit:

[local]#show circuit summary
Summary:
total: 7
up: 7        down: 0
bound: 5     unbound: 2
auth: 0      interface: 5   subscriber: 0    bypass: 0
no-bind: 2   atm: 0         chdlc: 0         dot1q: 2
ether: 3     fr: 0          gre: 0
mpls: 0      ppp: 0         pppoe: 0
clips: 0     vpls: 0        ipip: 0
ipsec: 2     ipv6v4-man: 0  ipv6v4-auto: 0 
[local]#

1.12   RBN-CIRCUIT-GROUP-MIB

Defines the objects used to monitor circuit group policies.

The following sections contain object information for RBN-CIRCUIT-GROUP-MIB.

1.12.1   rbnCircuitGroupStatsTable

Contains various transmit, receive, and drop counters for each circuit group.

Index: rbnCctGrpName

Table 18 describes the attributes in rbnCircuitGroupStatsTable. All objects in the table are read-only unless otherwise specified.

Table 18    Objects in rbnCircuitGroupStatsTable

Object and Object Identifier

Type

Value Range

Description

rbnCctGrpTxOctets


rbnCircuitGroupStatsEntry 2


1.3.6.1.4.1.2352.2.43.1.1.1.

Counter64

N/A

Number of octets transmitted by the group including its children.

rbnCctGrpTxPackets


rbnCircuitGroupStatsEntry 3


1.3.6.1.4.1.2352.2.43.1.1.1.3

Counter64

N/A

Number of packets transmitted by the group including its children.

rbnCctGrpTxMulticastOctets


rbnCircuitGroupStatsEntry 4


1.3.6.1.4.1.2352.2.43.1.1.1.4

Counter64

N/A

Number of multicast octets transmitted by the group including its children.

rbnCctGrpTxMulticastPackets


rbnCircuitGroupStatsEntry 5


1.3.6.1.4.1.2352.2.43.1.1.1.5

Counter64

N/A

Number of multicast packets transmitted by the group including its children.

rbnCctGrpRxOctets


rbnCircuitGroupStatsEntry 6


1.3.6.1.4.1.2352.2.43.1.1.1.6

Counter64

N/A

Number of octets received by the group including its children.

rbnCctGrpRxPackets


rbnCircuitGroupStatsEntry 7


1.3.6.1.4.1.2352.2.43.1.1.1.7

Counter64

N/A

Number of packets received by the group including its children.

rbnCctGrpRxMulticastOctets


rbnCircuitGroupStatsEntry 8


1.3.6.1.4.1.2352.2.43.1.1.1.8

Counter64

N/A

Number of multicast octets received by the group including its children.

rbnCctGrpRxMulticastPackets


rbnCircuitGroupStatsEntry 9


1.3.6.1.4.1.2352.2.43.1.1.1.9

Counter64

N/A

Number of multicast packets received by the group including its children.

rbnCctGrpAdjDroppedOctets


rbnCircuitGroupStatsEntry 10


1.3.6.1.4.1.2352.2.43.1.1.1.10

Counter64

N/A

Number of adjacency octets dropped.

rbnCctGrpAdjDroppedPackets


rbnCircuitGroupStatsEntry 11


1.3.6.1.4.1.2352.2.43.1.1.1.11

Counter64

N/A

Number of adjacency packets dropped.

rbnCctGrpDownDroppedOctets


rbnCircuitGroupStatsEntry 12


1.3.6.1.4.1.2352.2.43.1.1.1.12

Counter64

N/A

Number of down octets dropped.

rbnCctGrpDownDroppedPackets


rbnCircuitGroupStatsEntry 13


1.3.6.1.4.1.2352.2.43.1.1.1.13

Counter64

N/A

Number of down packets dropped.

rbnCctGrpUnreachDroppedOctets


rbnCircuitGroupStatsEntry 14


1.3.6.1.4.1.2352.2.43.1.1.1.14

Counter64

N/A

Number of unreachable octets dropped.

rbnCctGrpUnreachDroppedPackets


rbnCircuitGroupStatsEntry 15


1.3.6.1.4.1.2352.2.43.1.1.1.15

Counter64

N/A

Number of unreachable packets dropped.

rbnCctGrpUnknownEncapsOctets


rbnCircuitGroupStatsEntry 16


1.3.6.1.4.1.2352.2.43.1.1.1.16

Counter64

N/A

Number octets dropped due to unknown encapsulation.

rbnCctGrpUnknownEncapsPackets


rbnCircuitGroupStatsEntry 17


1.3.6.1.4.1.2352.2.43.1.1.1.17

Counter64

N/A

Number of packets dropped due to unknown encapsulation.

1.12.2   rbnCircuitGroupQTable

Contains various counters for each transmit queue assigned to a circuit group.

Index: rbnCctGrpName, rbnCctGrpQueueId

Table 19 describes the attributes in rbnCircuitGroupQTable. All objects in the table are read-only unless otherwise specified.

Table 19    Objects in rbnCircuitGroupQTable

Object and Object Identifier

Type

Value Range

Description

rbnCctGrpQTxOctets


rbnCircuitGroupQEntry 2


1.3.6.1.4.1.2352.2.43.1.2.1.2

Counter64

N/A

Number of octets transmitted out of this queue.


Discontinuities in the value of this counter can occur at reinitialization of the management system.

rbnCctGrpQTxPackets


rbnCircuitGroupQEntry 3


1.3.6.1.4.1.2352.2.43.1.2.1.3

Counter64

N/A

Number of packets transmitted out of this queue.


Discontinuities in the value of this counter can occur at reinitialization of the management system.

rbnCctGrpQWredDroppedOctets


rbnCircuitGroupQEntry 4


1.3.6.1.4.1.2352.2.43.1.2.1.4

Counter64

N/A

Number of octets dropped due to the application of a weighted random early detection (WRED) algorithm.


Discontinuities in the value of this counter can occur at reinitialization of the management system.

rbnCctGrpQWredDroppedPkts


rbnCircuitGroupQEntry 5


1.3.6.1.4.1.2352.2.43.1.2.1.5

Counter64

N/A

Number of packets dropped due to the application of a WRED algorithm.


Discontinuities in the value of this counter can occur at reinitialization of the management system.

rbnCctGrpQTailDroppedOctets


rbnCircuitGroupQEntry 6


1.3.6.1.4.1.2352.2.43.1.2.1.6

Counter64

N/A

Number of octets dropped when the total number of packets in this queue is greater than the maximum threshold.


Discontinuities in the value of this counter can occur at reinitialization of the management system.

rbnCctGrpQTailDroppedPkts


rbnCircuitGroupQEntry 7


1.3.6.1.4.1.2352.2.43.1.2.1.7

Counter64

N/A

Number of packets dropped when the total number of packets in this queue is greater than the maximum threshold.


Discontinuities in the value of this counter can occur at reinitialization of the management system.

1.12.3   rbnCctGrpRLPolicyStatsTable

Contains counters for rate-limiting policies applied to circuit groups.

Index: rbnCctGrpName, rbnCctGrpRLPolicyType

Table 20 describes the attributes in rbnCctGrpRLPolicyStatsTable. All objects in the table are read-only unless otherwise specified.

Table 20    Objects in rbnCctGrpRLPolicyStatsTable

Object and Object Identifier

Type

Value Range

Description

rbnCctGrpRLPolicyName


rbnCctGrpRLPolicyStatsEntry 2


1.3.6.1.4.1.2352.2.43.1.3.1.2

SnmpAdminString

SIZE (1–39)

Name of the rate-limit policy.

rbnCctGrpRLPolicyConformOctets


rbnCctGrpRLPolicyStatsEntry 3


1.3.6.1.4.1.2352.2.43.1.3.1.3

Counter64

N/A

Number of octets that conform to the rate limit set on the circuit group for which counters are enabled.

rbnCctGrpRLPolicyConformPkts


rbnCctGrpRLPolicyStatsEntry 4


1.3.6.1.4.1.2352.2.43.1.3.1.4

Counter64

N/A

Number of packets that conform to the rate limit set on the circuit group for which counters are enabled.

rbnCctGrpRLPolicyExceedOctets


rbnCctGrpRLPolicyStatsEntry 5


1.3.6.1.4.1.2352.2.43.1.3.1.5

Counter64

N/A

Number of octets that exceed the rate limit set on the interface for which class counters are enabled.

rbnCctGrpRLPolicyExceedPkts


rbnCctGrpRLPolicyStatsEntry 6


1.3.6.1.4.1.2352.2.43.1.3.1.6

Counter64

N/A

Number of packets that exceed the rate limit set on the interface.

rbnCctGrpRLPolicyExceedDroppedOctets


rbnCctGrpRLPolicyStatsEntry 7


1.3.6.1.4.1.2352.2.43.1.3.1.7

Counter64

N/A

Number of octets that were dropped due to the application of an exceed action on packets that exceed the rate limit set on the circuit group for which counters are enabled.

rbnCctGrpRLPolicyExceedDroppedPkts


rbnCctGrpRLPolicyStatsEntry 8


1.3.6.1.4.1.2352.2.43.1.3.1.8

Counter64

N/A

Number of packets that were dropped due to the application of an exceed action on packets that exceed the rate limit set on the circuit group for which counters are enabled.

rbnCctGrpRLPolicyViolateOctets


rbnCctGrpRLPolicyStatsEntry 9


1.3.6.1.4.1.2352.2.43.1.3.1.9

Counter64

N/A

Number of octets that violate the normal and maximum burst sizes on the circuit group for which counters are enabled.

rbnCctGrpRLPolicyViolatePkts


rbnCctGrpRLPolicyStatsEntry 10


1.3.6.1.4.1.2352.2.43.1.3.1.10

Counter64

N/A

Number of packets that violate the normal and maximum burst sizes on the circuit group for which counters are enabled.

rbnCctGrpRLPolicyViolateDroppedOctets


rbnCctGrpRLPolicyStatsEntry 11


1.3.6.1.4.1.2352.2.43.1.3.1.11

Counter64

N/A

Number of octets that were dropped due to the application of a violate action on packets that violate the normal and maximum burst sizes on the circuit group for which counters are enabled.

rbnCctGrpRLPolicyViolateDroppedPkts


rbnCctGrpRLPolicyStatsEntry 12


1.3.6.1.4.1.2352.2.43.1.3.1.12

Counter64

N/A

Number of packets that were dropped due to the application of a violate action on packets that violate the normal and maximum burst sizes on the circuit group for which counters are enabled.

1.12.4   rbnCctGrpRLClassStatsTable

Contains counters for rate limit policy classes applied to circuit groups.

Index: rbnCctGrpName, rbnCctGrpRLPolicyType, rbnCctGrpRLClassId

Table 21 describes the attributes in rbnCctGrpRLClassStatsTable. All objects in the table are read-only unless otherwise specified.

Table 21    Objects in rbnCctGrpRLClassStatsTable

Object and Object Identifier

Type

Value Range

Description

rbnCctGrpRLClassName


rbnCctGrpRLClassStatsEntry 2


1.3.6.1.4.1.2352.2.43.1.4.1.2

SnmpAdminString

SIZE (1–39)

Name of the class in the rate-limiting policy access list.

rbnCctGrpRLClassConformOctets


rbnCctGrpRLClassStatsEntry 3


1.3.6.1.4.1.2352.2.43.1.4.1.3

Counter64

N/A

Number of octets that conform to the policy class rate limit set on the circuit group.

rbnCctGrpRLClassConformPkts


rbnCctGrpRLClassStatsEntry 4


1.3.6.1.4.1.2352.2.43.1.4.1.4

Counter64

N/A

Number of packets that conform to the policy class rate limit set on the circuit group.

rbnCctGrpRLClassConformDroppedOctets


rbnCctGrpRLClassStatsEntry 5


1.3.6.1.4.1.2352.2.43.1.4.1.5

Counter64

N/A

Number of octets that were dropped due to the application of a conform action on packets that conform to the policy class rate limit set on the circuit group.

rbnCctGrpRLClassConformDroppedPkts


rbnCctGrpRLClassStatsEntry 6


1.3.6.1.4.1.2352.2.43.1.4.1.6

Counter64

N/A

Number of packets that were dropped due to the application of a conform action on packets that conform to the policy class rate limit set on the circuit group.

rbnCctGrpRLClassExceedOctets


rbnCctGrpRLClassStatsEntry 7


1.3.6.1.4.1.2352.2.43.1.4.1.7

Counter64

N/A

Number of octets that exceed the policy class rate limit set on the circuit group.

rbnCctGrpRLClassExceedPkts


rbnCctGrpRLClassStatsEntry 8


1.3.6.1.4.1.2352.2.43.1.4.1.8

Counter64

N/A

Number of packets that exceed the policy class rate limit set on the circuit group.

rbnCctGrpRLClassExceedDroppedOctets


rbnCctGrpRLClassStatsEntry 9


1.3.6.1.4.1.2352.2.43.1.4.1.9

Counter64

N/A

Number of octets that were dropped due to the application of an exceed action on packets that exceed the policy class rate limit set on the circuit group.

rbnCctGrpRLClassExceedDroppedPkts


rbnCctGrpRLClassStatsEntry 10


1.3.6.1.4.1.2352.2.43.1.4.1.10

Counter64

N/A

Number of packets that were dropped due to the application of an exceed action on packets that exceed the policy class rate limit set on the circuit group.

rbnCctGrpRLClassViolateOctets


rbnCctGrpRLClassStatsEntry 11


1.3.6.1.4.1.2352.2.43.1.4.1.11

Counter64

N/A

Number of octets that violate the normal and maximum burst sizes on the circuit group.

rbnCctGrpRLClassViolatePkts


rbnCctGrpRLClassStatsEntry 12


1.3.6.1.4.1.2352.2.43.1.4.1.12

Counter64

N/A

Number of packets that violate the normal and maximum burst sizes on the circuit group.

rbnCctGrpRLClassViolateDroppedOctets


rbnCctGrpRLClassStatsEntry 13


1.3.6.1.4.1.2352.2.43.1.4.1.13

Counter64

N/A

Number of octets that were dropped due to the application of a violate action on packets that violate the normal and maximum burst sizes on the circuit group.

rbnCctGrpRLClassViolateDroppedPkts


rbnCctGrpRLClassStatsEntry 14


1.3.6.1.4.1.2352.2.43.1.4.1.14

Counter64

N/A

Number of packets that were dropped due to the application of a violate action on packets that violate the normal and maximum burst sizes on the circuit group.

1.13   RBN-CONFIG-FILE-MIB

Saves the running SmartEdge router configuration on a File Transfer Protocol (FTP) or Trivial FTP (TFTP) server, and loads the SmartEdge router configuration files from a FTP or TFTP server.

The following sections contain object information for RBN-CONFIG-FILE-MIB.

1.13.1   RBN-CONFIG-FILE-MIB Objects

Table 22 describes the objects for the RBN-CONFIG-FILE-MIB.

Table 22    Objects in RBN-CONFIG-FILE-MIB

Object and Object Identifier

Type

Value Range

Description

rcfJobSpinLock


rcfJobs 1


1.3.6.1.4.1.2352.2.13.1.1.1

TestAndIncr

N/A

An advisory lock used to allow several cooperating Command Generator Applications to coordinate their use of facilities to create and modify entries in rcfJobTable. This object is read-write.

rcfJobNextIndex


rcfJobs 2


1.3.6.1.4.1.2352.2.13.1.1.2

Unsigned32

N/A

The next available index which can be used to create an rcfJobEntry object. This object is read-write.

1.13.2   rcfJobTable

Start and monitor a process that loads a configuration file or saves the current configuration to a file.

Use one of the following methods to create a new entry is:

Entries with a completed state are automatically deleted by the system after some system-dependent time.

Index: rcfJobIndex

Table 23 describes objects for the rcfJobTable. All objects in the table are read-only unless otherwise specified.

Table 23    Objects in rrcfJobTable

Object and Object Identifier

Type

Value Range

Description

rcfJobOp


rcfJobEntry 2


1.3.6.1.4.1.2352.2.13.1.1.3.1.2

Integer

0—load


1—save

The configuration operation to perform. If 'load', the file specified in the rcfJobFilename object is retrieved, parsed, and loaded into the system configuration. If 'save', the current system configuration is written to the file specified in the rcfJobFilename object. This object is read-create.

rcfJobProtocol


rcfJobEntry 3


1.3.6.1.4.1.2352.2.13.1.1.3.1.3

Integer

0—local


1—tftp


2—ftp

The file transfer protocol to use. If 'local', the filename specified in the rcfJobFilename object exists locally on the system (for example, in /flash). If 'tftp', the filename specified in the rcfJobFilename object is read or written from or to the system identified by the rcfJobIpAddress object through the TFTP file transfer protocol. If 'ftp', the filename specified in rcfJobFilename is read or written from or to the system identified by the rcfJobIpAddress object through the FTP file transfer protocol. The values in the rcfJobUsername object and the rcfJobPassword object are used for authentication. The rcfJobPassiveMode object can be used to enable or disable FTP's passive mode. This object is read-create.

rcfJobFilename


rcfJobEntry 4


1.3.6.1.4.1.2352.2.13.1.1.3.1.4

SnmpAdminString

SIZE (1–128)

The name of the source file (loads) or destination file (saves). This object is read-create.

rcfJobIpAddressType


rcfJobEntry 5


1.3.6.1.4.1.2352.2.13.1.1.3.1.5

InetAddressType


Integer

0—unknown


1—ipv4


2—ipv6


16—dns

The address type for the rcfJobIpAddress object. This object is only relevant for nonlocal filenames. If the rcfJobProtocol object equals 'local', any value for this object is ignored. This object is read-create.

rcfJobIpAddress


rcfJobEntry 6


1.3.6.1.4.1.2352.2.13.1.1.3.1.6

InetAddress


String

SIZE (0–255)

The IP address for the file server that contains the source file (loads) or destination file (saves). This object is only relevant for nonlocal filenames. If the rcfJobProtocol object equals 'local', any value for this object is ignored. This object is read-create.

rcfJobUsername


rcfJobEntry 7


1.3.6.1.4.1.2352.2.13.1.1.3.1.7

SnmpAdminString

SIZE (1–32)

The username to use for authentication with the file server. This object is only relevant for the FTP protocol. If the rcfJobProtocol object does not equal 'ftp', any value for this object is ignored. For security reasons, all SNMP get actions on this object return a zero-length string. This object is read-create.

rcfJobPassword


rcfJobEntry 8


1.3.6.1.4.1.2352.2.13.1.1.3.1.8

SnmpAdminString

SIZE (0–128)

The password to use for authentication with the file server. A zero-length string value is used for usernames that do not require a password. This object is only relevant for the FTP protocol. If the rcfJobProtocol object does not equal 'ftp', any value for this object will effectively be ignored. For security reasons, all SNMP gets on this object return a zero-length string. This object is read-create.

rcfJobPassiveMode


rcfJobEntry 9


1.3.6.1.4.1.2352.2.13.1.1.3.1.9

TruthValue

1—true


2—false

Enables or disables passive mode on FTP connections. This object is only relevant for the FTP protocol. If the rcfJobProtocol object does not equal 'ftp', any value for this object is ignored. This object is read-create.

rcfJobStopAtLine


rcfJobEntry 10


1.3.6.1.4.1.2352.2.13.1.1.3.1.10

Unsigned32

N/A

If this object instance has a non zero value, parsing and loading of the configuration file stops after the specified line number. This object is only relevant for 'load' operations. If the rcfJobOp object does not equal 'load', any value for this object is ignored. This object is read-create.

rcfJobSaveDefaults


rcfJobEntry 11


1.3.6.1.4.1.2352.2.13.1.1.3.1.11

TruthValue

1—true


2—false

If the value of this object is true, the default values for all configuration values are saved. If the value of this object is false, only the values that have been explicitly configured are saved. This object is only relevant for 'save' operations. If the rcfJobOp object does not equal 'save', any value for this object is ignored. This object is read-create.

rcfJobState


rcfJobEntry 12


1.3.6.1.4.1.2352.2.13.1.1.3.1.12

Integer

0—pending


1—inProgress


2—completed

The current state of the configuration job.

rcfJobResult


rcfJobEntry 13


1.3.6.1.4.1.2352.2.13.1.1.3.1.13

Integer

0—success


1—other


2—noMemory


3—parse


4—io


5—access

A generic result code. This object is instantiated only when the value of the rcfJobStatus object is completed. More detailed error descriptions can be found in the rcfJobErrorMsgs object.

rcfJobErrorMsgs


rcfJobEntry 14


1.3.6.1.4.1.2352.2.13.1.1.3.1.14

SnmpAdminString

N/A

Detailed error messages generated during the configuration operation. This object is instantiated only when the rcfJobState object equals 'completed'. Note: The amount of error messages produced by a configuration operation may exceed the maximum size of this object (255 bytes). If this happens, the last character in the rcfJobErrorMsgs value is '$' to indicate that a truncation occurred. Note: Some messages that appear when you configure an operation through the CLI are not be seen in the values for this object. For example, on the SMS platform, the CLI displays messages when there is a parse failure. These messages are not be captured in this object.

rcfJobCreateTime


rcfJobEntry 15


1.3.6.1.4.1.2352.2.13.1.1.3.1.15

TimeStamp

N/A

The value of sysUpTime when this job entry was created.

rcfJobStartTime


rcfJobEntry 16


1.3.6.1.4.1.2352.2.13.1.1.3.1.16

TimeStamp

N/A

The value of the sysUpTime object when the rcfJobState object moved from pending to inProgress. This object is not instantiated until the value of the rcfJobState object changes to inProgress. The object is uninstantiated if the value of the rcfJobRowStatus object is set to notInService.

rcfJobStopTime


rcfJobEntry 17


1.3.6.1.4.1.2352.2.13.1.1.3.1.17

TimeStamp

N/A

This object is not instantiated until the value of the rcfJobState object changes to completed. The object will be uninstantiated if the rcfJobRowStatus object is set to notInService.

rcfJobNotifyOnCompletion


rcfJobEntry 18


1.3.6.1.4.1.2352.2.13.1.1.3.1.18

TruthValue

1—true


2—false

If the value of this object is true, an rcfJobCompleted notification is generated when the job completes. This object is read-create.

rcfJobOwner


rcfJobEntry 19


1.3.6.1.4.1.2352.2.13.1.1.3.1.19

OwnerString


String

SIZE (0–127)

This object can be used to identify who created this job entry and when. This object is read-create.

rcfJobRowStatus


rcfJobEntry 20


1.3.6.1.4.1.2352.2.13.1.1.3.1.20

RowStatus


Integer

1—active


2—notInService


3—notReady


4—createAndGo


5—createAndWait


6—destroy

The row status for creating, modifying, or deleting an entry in the table.


Entries with a value of active cannot be modified.


Any attempt to modify an object in this entry while the rcfJobRowStatus object equals 'active' results in an inconsistentValue error.


To modify objects in an active entry, the rcfJobRowStatus object must first be set to notInService.


All entries are automatically deleted by the agent after some system-dependent time. This object is read-create.

1.13.3   Example: Use RBN-CONFIG-FILE-MIB to Save System Configuration

You can use the RBN-CONFIG-FILE-MIB to save the system configuration using SNMP.

The rcfJobTable in RBN-CONFIG-FILE-MIB enterprise MIB is used to save or load configuration files to and from a TFTP or FTP server. To create a save request job, the next available index for rcfJobTable must be obtained using the rcfJobNextIndex object as follows:

sh$ snmpget -c public -v 2c SE-lab2 rcfJobNextIndex.0 
RBN-CONFIG-FILE-MIB::rcfJobNextIndex.0 = Gauge32: 1
sh$

The preceding output shows that the ‘1’ is the next available index. The save config request can be made with rcfJobNextIndex = 1 by creating a row entry in rcfJobTable:

sh$ snmpset -c private -v 2c SE-lab2 rcfJobOp.1 i save rcfJobProtocol.1
 i local rcfJobFilename.1 s /md/snmpsave.cfg rcfJobOwner.1 s jsmith 
rcfJobRowStatus.1 i createAndGo
RBN-CONFIG-FILE-MIB::rcfJobOp.1 = INTEGER: save(1)
RBN-CONFIG-FILE-MIB::rcfJobProtocol.1 = INTEGER: local(0)
RBN-CONFIG-FILE-MIB::rcfJobFilename.1 = STRING: /md/snmpsave.cfg
RBN-CONFIG-FILE-MIB::rcfJobOwner.1 = STRING: "jsmith"
RBN-CONFIG-FILE-MIB::rcfJobRowStatus.1 = INTEGER: createAndGo(4)
Note:  
The rcfJobOwner object is optional

To view the request status, the rcfJobState object must be retrieved as shown in the following example:

sh$ snmpget -c public -v 2c SE-lab2 rcfJobState.1
RBN-CONFIG-FILE-MIB::rcfJobState.1 = INTEGER: inProgress(1)

After a few seconds, the job status shows ‘completed’ as follows:

sh$ snmpget -c public -v 2c SE-lab2 rcfJobState.1
RBN-CONFIG-FILE-MIB::rcfJobState.1 = INTEGER: completed(2)

The following shows the MIB walk for the table:

sh$ snmpwalk -c public -v 2c SE-lab2 rcfJobs
RBN-CONFIG-FILE-MIB::rcfJobSpinLock.0 = INTEGER: 1
RBN-CONFIG-FILE-MIB::rcfJobNextIndex.0 = Gauge32: 2
RBN-CONFIG-FILE-MIB::rcfJobOp.1 = INTEGER: save(1)
RBN-CONFIG-FILE-MIB::rcfJobProtocol.1 = INTEGER: local(0)
RBN-CONFIG-FILE-MIB::rcfJobFilename.1 = STRING: /md/snmpsave.cfg
RBN-CONFIG-FILE-MIB::rcfJobStopAtLine.1 = Gauge32: 0
RBN-CONFIG-FILE-MIB::rcfJobSaveDefaults.1 = INTEGER: false(2)
RBN-CONFIG-FILE-MIB::rcfJobState.1 = INTEGER: completed(2)
RBN-CONFIG-FILE-MIB::rcfJobResult.1 = INTEGER: success(0)
RBN-CONFIG-FILE-MIB::rcfJobErrorMsgs.1 = STRING: 
RBN-CONFIG-FILE-MIB::rcfJobCreateTime.1 = Timeticks: (22738049) 2 days,
 15:09:40.49
RBN-CONFIG-FILE-MIB::rcfJobStartTime.1 = Timeticks: (22738049) 2 days,
 15:09:40.49
RBN-CONFIG-FILE-MIB::rcfJobStopTime.1 = Timeticks: (22740317) 2 days,
 15:10:03.17
RBN-CONFIG-FILE-MIB::rcfJobNotifyOnCompletion.1 = INTEGER: false(2)
RBN-CONFIG-FILE-MIB::rcfJobOwner.1 = STRING: "jsmith"
RBN-CONFIG-FILE-MIB::rcfJobRowStatus.1 = INTEGER: active(1)

The following shows an example of saving the file to an FTP server:

sh$ snmpset -c public -v 2c SE-lab2 rcfJobOp.2 i save rcfJobProtocol.2
 i ftp rcfJobIpAddressType.2 i ipv4

rcfJobIpAddress.2 d 172.16.8.2 rcfJobUsername.2 s lab rcfJobPassword.2
 s lab123 rcfJobFilename.2 s snmpsave.cfg  rcfJobOwner.2 s jsmith 
rcfJobRowStatus.2 i createAndGo 
RBN-CONFIG-FILE-MIB::rcfJobOp.2 = INTEGER: save(1)
RBN-CONFIG-FILE-MIB::rcfJobProtocol.2 = INTEGER: ftp(2)
RBN-CONFIG-FILE-MIB::rcfJobIpAddressType.2 = INTEGER: ipv4(1)
RBN-CONFIG-FILE-MIB::rcfJobIpAddress.2 = Hex-STRING: AC 10 08 02 
RBN-CONFIG-FILE-MIB::rcfJobUsername.2 = STRING: lab
RBN-CONFIG-FILE-MIB::rcfJobPassword.2 = STRING: lab123
RBN-CONFIG-FILE-MIB::rcfJobFilename.2 = STRING: snmpsave.cfg
RBN-CONFIG-FILE-MIB::rcfJobNotifyOnCompletion.2 = INTEGER: false(2)
RBN-CONFIG-FILE-MIB::rcfJobOwner.2 = STRING: "jsmith"
RBN-CONFIG-FILE-MIB::rcfJobRowStatus.2 = INTEGER: createAndGo(4)

The following shows an example of loading a configuration file from an FTP server:

sh$ snmpset -c public -v 2c SE-lab2 rcfJobOp.3 i load rcfJobProtocol.3
 i ftp rcfJobIpAddressType.3 i ipv4 rcfJobIpAddress.3 d 172.16.8.2
 rcfJobUsername.3 s lab 

rcfJobPassword.3 s lab123 rcfJobFilename.3 s snmpsave.cfg  
rcfJobOwner.3 s jsmith rcfJobRowStatus.3 i createAndGo 
RBN-CONFIG-FILE-MIB::rcfJobOp.3 = INTEGER: load(0)
RBN-CONFIG-FILE-MIB::rcfJobProtocol.3 = INTEGER: ftp(2)
RBN-CONFIG-FILE-MIB::rcfJobIpAddressType.3 = INTEGER: ipv4(1)
RBN-CONFIG-FILE-MIB::rcfJobIpAddress.3 = Hex-STRING: AC 10 08 02 
RBN-CONFIG-FILE-MIB::rcfJobUsername.3 = STRING: lab
RBN-CONFIG-FILE-MIB::rcfJobPassword.3 = STRING: lab123
RBN-CONFIG-FILE-MIB::rcfJobFilename.3 = STRING: snmpsave.cfg
RBN-CONFIG-FILE-MIB::rcfJobNotifyOnCompletion.3 = INTEGER: false(2)
RBN-CONFIG-FILE-MIB::rcfJobOwner.3 = STRING: "jsmith"
RBN-CONFIG-FILE-MIB::rcfJobRowStatus.3 = INTEGER: createAndGo(4)

The following shows the related CLI commands:

[local]#save configuration ?
/md    Save into the Micro Drive
WORD   source file in format [/dir/]filename
ftp:   File Transfer Protocol
rcp:   Remote Copy Protocol
scp:   Secured Copy Protocol
sftp:  Secured File Transfer Protocol
tftp:  Trivial File Transfer Protocol
<cr>

[local]# configuration ?
WORD   URL of configuration file
ftp:   File Transfer Protocol
rcp:   Remote Copy Protocol
scp:   Secured Copy Protocol
sftp:  Secured File Transfer Protocol
tftp:  Trivial File Transfer Protocol
<cr>

1.14   RBN-CPU-METER-MIB

Manages CPU utilization.

The following sections contain object information for RBN-CPU-METER-MIB.

1.14.1   RBN-CPU-METER-MIB Objects

Table 24 describes the objects in RBN-CPU-METER-MIB. All objects in the table are read-only.

Table 24    Objects in RBN-CPU-METER-MIB

Object and Object Identifier

Type

Value Range

Description

rbnCpuMeterFiveSecondAvg


rbnCpuMeterMIBObjects 1


1.3.6.1.4.1.2352.2.6.1.1

RbnPercentage


Integer32

0–100

Provides the CPU usage percentage over the first five second period in the scheduler.

rbnCpuMeterOneMinuteAvg


rbnCpuMeterMIBObjects 2


1.3.6.1.4.1.2352.2.6.1.2

RbnPercentage


Integer32

0–100

Provides a cumulative average of the CPU usage percentage over a one minute period.

rbnCpuMeterFiveMinuteAvg


rbnCpuMeterMIBObjects 3


1.3.6.1.4.1.2352.2.6.1.3

RbnPercentage


Integer32

0–100

Provides a cumulative average of the CPU usage percentage over a five-minute period.

1.14.2   rbnCpuProcTable

This table contains the objects that identify CPU processes. Entries in the table are created or deleted as processes are started or terminated.

Index: IMPLIED rbnCpuProcName

Table 25 describes the attributes in rbnCpuProcTable. All objects in the table are read-only.

Table 25    Objects in rbnCpuProcTable

Object and Object Identifier

Type

Value Range

Description

rbnCpuProcName


rbnCpuProcEntry 1


1.3.6.1.4.1.2352.2.6.3.1.1.1

DisplayString

SIZE (1–128)

The name for this process.

rbnCpuProcPriority


rbnCpuProcEntry 2


1.3.6.1.4.1.2352.2.6.3.1.1.2

Unsigned32

0–255

The priority of this process. This value ranges from 0 to 255, with 0 being the highest priority.

rbnCpuProcTime


rbnCpuProcEntry 3


1.3.6.1.4.1.2352.2.6.3.1.1.3

Counter32

N/A

The total time, in milliseconds, spent in this process.

rbnCpuProcCalls


rbnCpuProcEntry 4


1.3.6.1.4.1.2352.2.6.3.1.1.4

Counter32

N/A

The number of times that this process has acquired the CPU.

rbnCpuProc5Sec


rbnCpuProcEntry 5


1.3.6.1.4.1.2352.2.6.3.1.1.5

RbnPercentage


Integer32

0–100

The average CPU usage in a 5-second window for this process.

rbnCpuProc1Min


rbnCpuProcEntry 6


1.3.6.1.4.1.2352.2.6.3.1.1.6

RbnPercentage


Integer32

0–100

The average CPU usage in a 1-minute window for this process.

rbnCpuProc5Min


rbnCpuProcEntry 7


1.3.6.1.4.1.2352.2.6.3.1.1.7

RbnPercentage


Integer32

0–100

The average CPU usage in a 5-minute window for this process.

rbnCpuProcLongest


rbnCpuProcEntry 8


1.3.6.1.4.1.2352.2.6.3.1.1.8

Gauge32

N/A

The maximum time, in milliseconds, spent in this process.

1.14.3   Example

You can use the RBN-CPU-METER-MIB to collect CPU usage periodically for trend analysis that the management system uses.

The five-second-average output looks like this:

sh-3.00$ snmpbulkwalk -v2c -cpublic -m RBN-CPU-METER-MIB oak.lab 
rbnCpuMeterFiveSecondAvg 
RBN-CPU-METER-MIB::rbnCpuMeterFiveSecondAvg.0 = INTEGER: 3

The one-minute-average output looks like this:

sh-3.00$ snmpbulkwalk -v2c -cpublic -m RBN-CPU-METER-MIB oak.lab 
rbnCpuMeterOneMinuteAvg 
RBN-CPU-METER-MIB::rbnCpuMeterOneMinuteAvg.0 = INTEGER: 0

The five-minute-average output looks like this:

sh-3.00$ snmpbulkwalk -v2c -cpublic -m RBN-CPU-METER-MIB oak.lab 
rbnCpuMeterFiveMinuteAvg 
RBN-CPU-METER-MIB::rbnCpuMeterFiveMinuteAvg.0 = INTEGER: 0

The preceding information is obtained using the show process cpustats command as shown in the following example:

[local]rocky#show process cpustats
Total system CPU % usage (5s, 1m, 5m):  3.41,  0.83,  0.29 <output truncated>

1.15   RBN-DHCP-MIB

Provides a table for monitoring the configuration and statistics of Dynamic Host Configuration Protocol (DHCP) range thresholds in an interface, and a group of scalars for monitoring the configuration and statistics of DHCP thresholds for the context.

The following sections contain object information for RBN-DHCP-MIB.

1.15.1   DHCP Threshold Per Context Objects

Table 26 describes the DHCP Threshold Per Context Objects in the RBN-DHCP-MIB. All objects in the table are read-only unless otherwise specified.

Table 26    Objects in DHCP Threshold Per Context

Object and Object Identifier

Type

Value Range

Description

rbnDhcpCtxThreshold


rbnDhcpMIBObjects 2


1.3.6.1.4.1.2352.2.30.1.2

 

N/A

 

rbnDhcpCtxThresholdName


rbnDhcpCtxThreshold 1


1.3.6.1.4.1.2352.2.30.1.2.1

SnmpAdminString

SIZE (0–63)

Identifies the context in which a falling or rising per-context threshold event occurs. This object is accessible-for-notify.

rbnDhcpCtxThresholdSize


rbnDhcpCtxThreshold 2


1.3.6.1.4.1.2352.2.30.1.2.2

Unsigned32

N/A

Total number of leases in all DHCP ranges of all interfaces in the context valid in the current view.

rbnDhcpCtxThresholdAvailable


rbnDhcpCtxThreshold 3


1.3.6.1.4.1.2352.2.30.1.2.3

Unsigned32

N/A

Total number of leases available in all DHCP ranges of all interfaces in the context valid in the current view.

rbnDhcpCtxThresholdInuse


rbnDhcpCtxThreshold 4


1.3.6.1.4.1.2352.2.30.1.2.4

Unsigned32

N/A

Total number of leases in use in all DHCP ranges of all interfaces in the context valid in the current view.

rbnDhcpCtxThresholdFallingThreshold


rbnDhcpCtxThreshold 5


1.3.6.1.4.1.2352.2.30.1.2.5

Unsigned32

0–196608

The falling threshold value for the context valid in the current view. Just as the rbnDhcpIntfThresholdFallingThreshold object is the per-interface falling threshold, this object is the per-context falling threshold.


When the sum of the all available DHCP leases in all interfaces of the context valid in the current view reaches the value of this object, a trap, a log message, or both are generated.


Evaluation of whether to perform the action occurs on allocation of a lease from the available pool of leases from any interface within the context.


The values of the rbnDhcpCtxThresholdFallingSendTrap object and the rbnDhcpCtxThresholdFallingLogMessage object determine whether to send a trap or a log message.


If there is no per-context rising threshold, the value of this object is zero and the values of the rbnDhcpCtxThresholdFallingSendTrap object and the rbnDhcpCtxThresholdFallingLogMessage object are false.

rbnDhcpCtxThresholdFallingSendTrap


rbnDhcpCtxThreshold 6


1.3.6.1.4.1.2352.2.30.1.2.6

TruthValue

1—true


2—false

If the value of this object is true, on reaching the per-context falling threshold, a trap is sent. See the definition of the rbnDhcpCtxThresholdFallingThresholdMet notification for the information included in the trap.

rbnDhcpCtxThresholdFallingLogMessage


rbnDhcpCtxThreshold 7


1.3.6.1.4.1.2352.2.30.1.2.7

TruthValue

1—true


2—false

If the value of this object is true on reaching the per-context falling threshold, a message is logged. The information contained in the message logged is the same as that included in the rbnDhcpCtxThresholdFallingThresholdMet notification.

rbnDhcpCtxThresholdRisingThreshold


rbnDhcpCtxThreshold 8


1.3.6.1.4.1.2352.2.30.1.2.8

Unsigned32

0– 196608

The rising threshold value for the context valid in the current view. Just as the rbnDhcpIntfThresholdRisingThreshold object is the per interface rising threshold, this object is the per context rising threshold.


When the sum of the all available DHCP leases in all interfaces of the context valid in the current view reaches the value of this object a rising threshold action of a trap, a log message, or both will be generated.


This is a rising threshold, so the evaluation of whether to perform the action occurs upon return of a lease to the available pool of leases defined in any interface within the context.


The action of whether to send a trap or log message is specified by the values of the rbnDhcpCtxThresholdRisingSendTrap object and the rbnDhcpCtxThresholdRisingLogMessage object.


If there is no per context rising threshold, the value of this object will be zero and the values of the rbnDhcpCtxThresholdRisingSendTrap object and the rbnDhcpCtxThresholdRisingLogMessage object will be false.

rbnDhcpCtxThresholdRisingSendTrap


rbnDhcpCtxThreshold 9


1.3.6.1.4.1.2352.2.30.1.2.9

TruthValue

1—true


2—false

If the value of this object is true, upon detection of reaching the per context rising threshold, a trap will be sent. See the definition of the rbnDhcpCtxThresholdRisingThresholdMet object for the information included in the notification.

rbnDhcpCtxThresholdRisingLogMessage


rbnDhcpCtxThreshold 10


1.3.6.1.4.1.2352.2.30.1.2.10

TruthValue

1—true


2—false

If the value of this object is true, upon detection of reaching the per context rising threshold, a message will be logged. The information contained in the message logged is the same as that included in the rbnDhcpCtxThresholdRisingThresholdMet notification.

1.15.2   rbnDhcpIntfThresholdTable

This table allows monitoring of per-interface DHCP server thresholds through SNMP. This table contains the objects that characterize DHCP server thresholds. Each row in the table corresponds to information about the leases in a DHCP server range for a particular interface and the corresponding capacity, usage, and falling and rising thresholds. Objects defined in this table are only accessible within the context identified in the SNMP protocol (i.e. the community string in SNMPv1 or SNMPv2 or the contextName in SNMPv3).

Index: IMPLIED rbnDhcpIntfThresholdName

Table 27 describes the attributes in rbnDhcpIntfThresholdTable. All objects in the table are read-only unless otherwise specified.

Table 27    Objects in rbnDhcpIntfThresholdTable

Object and Object Identifier

Type

Value Range

Description

rbnDhcpIntfThresholdName


rbnDhcpIntfThresholdEntry 1

SnmpAdminString

SIZE (1–80)

The name of the interface. If you configure this entry using another tool (for example, a CLI), you can set it to a length greater than 80 characters. Names that exceed this length are not accessible through SNMP operations. This object is not accessible.

rbnDhcpIntfThresholdContextName


rbnDhcpIntfThresholdEntry 2

SnmpAdminString

SIZE (0–63)

The name of the context that contains the interface.

rbnDhcpIntfThresholdSize


rbnDhcpIntfThresholdEntry 3

Unsigned32

N/A

The number of leases reserved for the DHCP server in this interface.

rbnDhcpIntfThresholdAvailable


rbnDhcpIntfThresholdEntry 4

Unsigned32

N/A

The number of leases available in this interface.

rbnDhcpIntfThresholdInuse


rbnDhcpIntfThresholdEntry 5

Unsigned32

N/A

The number of leases in use in this interface.

rbnDhcpIntfThresholdFallingThreshold


rbnDhcpIntfThresholdEntry 6

Unsigned32

0–196608

Value that specifies that enabled falling threshold events are generated when the value of available leases drops to the falling threshold value. The value of available leases drops to the falling threshold value when a lease is taken from the pool. The number of available leases is reported in the rbnDhcpIntfThresholdAvailable object. A falling threshold event is either a notification, a log message, or both. Falling threshold events are enabled if either or both of the rbnDhcpIntfThresholdFallingSendTrap object and the rbnDhcpIntfThresholdFallingLogMessage object are true. A falling threshold event is triggered only on a transition of the value of the rbnDhcpIntfThresholdAvailable object dropping from (rbnDhcpIntfThresholdFallingThreshold+1) to rbnDhcpIntfThresholdFallingThreshold.

rbnDhcpIntfThresholdFallingSendTrap


rbnDhcpIntfThresholdEntry 7

TruthValue

1—true


2—false

If the value of this object is true, on reaching a falling threshold, a trap is sent. See the definition of the rbnDhcpIntfThresholdFallingThresholdMet notification for the information included in the trap.

rbnDhcpIntfThresholdFallingLogMessage


rbnDhcpIntfThresholdEntry 8

TruthValue

1—true


2—false

If the value of this object is true, on reaching a falling threshold, a message is logged. See the definition of the rbnDhcpIntfThresholdFallingThresholdMet notification for the information included in the trap.

rbnDhcpIntfThresholdRisingThreshold


rbnDhcpIntfThresholdEntry 9

Unsigned32

0– 196608

Value that specifies that any enabled rising threshold events are generated when the value of the currently available leases reaches the rising threshold value when a lease is returned to the pool. The number of available leases is reported in rbnDhcpIntfThresholdAvailable. A rising threshold event is a notification, or a log message, or both. Rising threshold events are enabled if either or both of rbnDhcpIntfThresholdRisingSendTrap and rbnDhcpIntfThresholdRisingLogMessage are true. A rising threshold event is triggered only on a transition of the value of rbnDhcpIntfThresholdAvailable increasing from (rbnDhcpIntfThresholdRisingThreshold-1) to rbnDhcpIntfThresholdRisingThreshold.

rbnDhcpIntfThresholdRisingSendTrap


rbnDhcpIntfThresholdEntry 10

TruthValue

1—true


2—false

If the value of this object is true, on reaching a rising threshold, a trap is sent. See the definition of the rbnDhcpIntfThresholdRisingThresholdMet notification for the information included in the trap.

rbnDhcpIntfThresholdRisingLogMessage


rbnDhcpIntfThresholdEntry 11

TruthValue

1—true


2—false

If the value of this object is true, on reaching a rising threshold, a message is logged. See the definition of the rbnDhcpIntfThresholdRisingThresholdMet notification for the information included in the trap.

1.15.3   rbnDhcpRangeThresholdTable

This table allows monitoring of DHCP server ranges on interfaces.

This table contains the objects which characterize DHCP server ranges. Each row in the table corresponds to information about the leases in a DHCP server for a particular range on a particular interface and the corresponding capacity, usage, and falling and rising thresholds.

Objects defined in this table are only accessible within the context identified in the SNMP protocol (that is, the community string in SNMPv1 or SNMPv2 or the contextName in SNMPv3).

Index: rbnDhcpRangeThresholdInterfaceIdx, rbnDhcpRangeThresholdAddr

Table 28 describes the attributes in rbnDhcpRangeThresholdTable. All objects in the table are read-only.

Table 28    Objects in rbnDhcpRangeThresholdTable

Object and Object Identifier

Type

Value Range

Description

rbnDhcpRangeThresholdEndAddr


rbnDhcpRangeThresholdEntry 3


1.3.6.1.4.1.2352.2.30.1.3.1.3

IpAddress


String

SIZE (4)

The end address of the DHCP range.

rbnDhcpRangeThresholdContextName


rbnDhcpRangeThresholdEntry 4


1.3.6.1.4.1.2352.2.30.1.3.1.4

SnmpAdminString

SIZE (0–63)

The name of the context that contains the interface.

rbnDhcpRangeThresholdInterfaceName


rbnDhcpRangeThresholdEntry 5


1.3.6.1.4.1.2352.2.30.1.3.1.5

SnmpAdminString

SIZE (1–80)

The name of the interface containing the DHCP range.

rbnDhcpRangeThresholdSize


rbnDhcpRangeThresholdEntry 6


1.3.6.1.4.1.2352.2.30.1.3.1.6

Unsigned32

N/A

The number of leases reserved for the DHCP server in this range.

rbnDhcpRangeThresholdAvailable


rbnDhcpRangeThresholdEntry 7


1.3.6.1.4.1.2352.2.30.1.3.1.7

Unsigned32

N/A

The number of leases available in this range.

rbnDhcpRangeThresholdInuse


rbnDhcpRangeThresholdEntry 8


1.3.6.1.4.1.2352.2.30.1.3.1.8

Unsigned32

N/A

The number of leases that are in use in this range.

rbnDhcpRangeThresholdFallingThreshold


rbnDhcpRangeThresholdEntry 9


1.3.6.1.4.1.2352.2.30.1.3.1.9

Unsigned32

0–196608

Value that specifies that enabled falling threshold events are generated when the value of available leases drops to the falling threshold value. The value of available leases drops to the falling threshold value when a lease is taken from the range. The number of available leases is reported in the rbnDhcpRangeThresholdAvailable object. A falling threshold event is a notification, a log message, or both. Falling threshold events are enabled if either or both of the rbnDhcpRangeThresholdFallingSendTrap object and the rbnDhcpRangeThresholdFallingLogMessage object are true. A falling threshold event is triggered only on a transition of the value of the rbnDhcpRangeThresholdAvailable object dropping from (rbnDhcpRangeThresholdFallingThreshold+1) to rbnDhcpRangeThresholdFallingThreshold.

rbnDhcpRangeThresholdFallingSendTrap


rbnDhcpRangeThresholdEntry 10


1.3.6.1.4.1.2352.2.30.1.3.1.10

TruthValue

1—true


2—false

If the value of this object is true, on reaching a falling threshold, a trap is sent. See the definition of the rbnDhcpRangeThresholdFallingThresholdMet notification for the information included in the trap.

rbnDhcpRangeThresholdFallingLogMessage


rbnDhcpRangeThresholdEntry 11


1.3.6.1.4.1.2352.2.30.1.3.1.11

TruthValue

1—true


2—false

If the value of this object is true, on reaching a falling threshold, a message is logged. See the definition of the rbnDhcpRangeThresholdFallingThresholdMet notification for the information included in the trap.

rbnDhcpRangeThresholdRisingThreshold


rbnDhcpRangeThresholdEntry 12


1.3.6.1.4.1.2352.2.30.1.3.1.12

Unsigned32

0– 196608

Value that specifies that any enabled rising threshold events are generated when the value of the currently available leases reaches the rising threshold value when a lease is returned to the range. The number of available leases is reported in the rbnDhcpRangeThresholdAvailable object. A rising threshold event is a notification, a log message, or both. Rising threshold events are enabled if either or both of the rbnDhcpRangeThresholdRisingSendTrap object and the rbnDhcpRangeThresholdRisingLogMessage object are true. A rising threshold event is triggered only on a transition of the value of the rbnDhcpRangeThresholdAvailable object increasing from (rbnDhcpRangeThresholdRisingThreshold-1) to rbnDhcpRangeThresholdRisingThreshold.

rbnDhcpRangeThresholdRisingSendTrap


rbnDhcpRangeThresholdEntry 13


1.3.6.1.4.1.2352.2.30.1.3.1.13

TruthValue

1—true


2—false

If the value of this object is true, on reaching a rising threshold, a trap is sent. See the definition of the rbnDhcpRangeThresholdRisingThresholdMet notification for the information included in the trap.

rbnDhcpRangeThresholdRisingLogMessage


rbnDhcpRangeThresholdEntry 14


1.3.6.1.4.1.2352.2.30.1.3.1.14

TruthValue

1—true


2—false

If the value of this object is true, on reaching a rising threshold, a message is logged. See the definition of the rbnDhcpRangeThresholdRisingThresholdMet notification for the information included in the trap.

1.16   RBN-DS1-MIB

Describes DS-1, E1, and E2 interface objects beyond those instrumented by standard MIBs. RBN-DS1-MIB is not supported on the SmartEdge 100 router.

1.16.1   rbnDsx1ConfigTable

Extends: dsx1ConfigEntry

Table 29 describes the attributes in rbnDsx1ConfigTable, the DS-1 configuration table. All objects in the table are read-only.

Table 29    Objects in rbnDsx1ConfigTable

Object and Object Identifier

Type

Value Range

Description

rbnDsx1AlarmSeverity


rbnDsx1ConfigEntry 1


1.3.6.1.4.1.2352.2.37.1.1.1.1

RbnAlarmPerceivedSeverity


Integer

1—cleared


2—critical


3—major


4—minor


5—warning

The perceived severity of the interface alarm.

rbnDsx1AlarmServiceAffecting


rbnDsx1ConfigEntry 2


1.3.6.1.4.1.2352.2.37.1.1.1.2

RbnAlarmServiceAffecting


Integer

1—yes


2—no

Indicates whether the interface alarm affects service.

1.17   RBN-DS3-MIB

Describes DS-3 and E3 interface objects, beyond those instrumented by standard MIBs. RBN-DS3-MIB is unsupported on the SmartEdge 100 router.

1.17.1   rbnDsx3ConfigTable

Index: dsx3LineIndex

Table 30 describes the attributes in rbnDsx3ConfigTable, the DS-3 or E-3 configuration table. All objects in the table are read-only.

Table 30    Objects in rbnDsx3ConfigTable

Object and Object Identifier

Type

Value Range

Description

rbnDsx3AlarmSeverity


rbnDsx3ConfigEntry 1


1.3.6.1.4.1.2352.2.38.1.1.1.1

RbnAlarmPerceivedSeverity


Integer

1—cleared


2—critical


3—major


4—minor


5—warning

The perceived severity of the interface alarm.

rbnDsx3AlarmServiceAffecting


rbnDsx3ConfigEntry 2


1.3.6.1.4.1.2352.2.38.1.1.1.2

RbnAlarmServiceAffecting


Integer

1—yes


2—no

Indicates whether the interface alarm affects service.

1.18   RBN-ENVMON-MIB

Generically manages environmental monitoring functions on SmartEdge router. Alarm conditions that are reported in this MIB are normal, failed, absent, or unknown. A new MIB table, rbnFanSpeedTable, displays the speed of the fan unit on the SmartEdge 100 router.

The following sections contain object information for RBN-ENVMON-MIB.

1.18.1   rbnFanStatusTable

This table contains one row for each fan test point. Note that there is not necessarily a one-to-one relationship between fan test points and fan assemblies; a single test point may be used to monitor the status of multiple fans.

Index: rbnFanIndex

Table 31 describes the attributes in rbnFanStatusTable. All objects in the table are read-only.

Table 31    Objects in rbnFanStatusTable

Object and Object Identifier

Type

Value Range

Description

rbnFanDescr


rbnFanStatusEntry 2


1.3.6.1.4.1.2352.2.4.1.1.1.2

DisplayString

SIZE (0–32)

The description of a fan test point. If an instance of this object is associated with a single fan assembly, the value of this object should be the same as the name by which the assembly is normally referenced. If an instance is associated with multiple fan assemblies, the value of this object should contain the names of all of the fan assemblies being monitored.

rbnFanFail


rbnFanStatusEntry 3


1.3.6.1.4.1.2352.2.4.1.1.1.3

TruthValue

1—true


2—false

The status of a fan test point. If an instance of this object has the value true, then a fan monitored by the test point has failed. If an instance of this object has the value false, then the fan or fans monitored by the test point are operational.

rbnFanStatus


rbnFanStatusEntry 4


1.3.6.1.4.1.2352.2.4.1.1.1.4

Integer

1—normal


2—failed


3—absent


4—unknown

The status of a fan test point. If an instance of this object has the value normal, then the fan or fans monitored by the test point is operational. If an instance of this object has the value failed, then the fan or fans monitored by the test point has failed. If an instance of this object has the value absent, then the fan or fans monitored by this test point is not present. If an instance of this object has the value unknown, then the test point is unable to monitor the fan or fans.

1.18.2   rbnPowerStatusTable

This table contains one row for each power test point. Note that there is not necessarily a one-to-one relationship between power test points and power supply assemblies; a single test point may be used to monitor the status of multiple power supplies.

Index: rbnPowerIndex

Table 32 describes the attributes in rbnPowerStatusTable. All objects in the table are read-only.

Table 32    Objects in rbnPowerStatusTable

Object and Object Identifier

Type

Value Range

Description

rbnPowerDescr


rbnPowerStatusEntry 2


1.3.6.1.4.1.2352.2.4.1.2.1.2

DisplayString

SIZE (0–32)

Description of a power supply test point. If an instance of this object is associated with a single power supply assembly, the value of this object should be the same as the name by which the assembly is normally referenced. If an instance is associated with multiple power supply assemblies, the value of this object should contain the names of all of the power supply assemblies being monitored.

rbnPowerFail


rbnPowerStatusEntry 3


1.3.6.1.4.1.2352.2.4.1.2.1.3

TruthValue

1—true


2—false

Status of a power test point. If an instance of this object has the value true, then a power supply monitored by the test point has failed. If an instance of this object has the value false, then the power supply (or supplies) monitored by the test point are operational.

rbnPowerStatus


rbnPowerStatusEntry 4


1.3.6.1.4.1.2352.2.4.1.2.1.4

Integer

1—normal


2—failed


3—absent


4—unknown

Status of a power test point. If an instance of this object has the value normal, the power supply (or supplies) monitored by the test point is operational. If an instance of this object has the value failed, the power supply (or supplies) monitored by the test point has failed. If an instance of this object has the value absent, the power supply (or supplies) monitored by this test point is not present. If an instance of this object has the value unknown, the test point is unable to monitor the power supply (or supplies).

1.18.3   rbnVoltageSensorTable

This table contains one row for each voltage test point. Each physical entity (for example, a card) in the system may have zero or more voltage test points.

Index: entPhysicalIndex, rbnVoltageIndex

Table 33 describes the attributes in rbnVoltageSensorTable. All objects in the table are read-only.

Table 33    Objects in rbnVoltageSensorTable

Object and Object Identifier

Type

Value Range

Description

rbnVoltageDescr


rbnVoltageSensorEntry 2


1.3.6.1.4.1.2352.2.4.1.3.1.2

DisplayString

SIZE (0–48)

Description of a voltage test point. Typically an instance of this object holds a user-friendly description of the physical entity and the level of voltage being monitored by this test point.

rbnVoltageDesired


rbnVoltageSensorEntry 3


1.3.6.1.4.1.2352.2.4.1.3.1.3

RbnVoltage


Unsigned32

0–50000

Desired voltage level for this test point. If the monitored voltage level (rbnVoltageCurrent) is equal to this value, the system is performing as designed.

rbnVoltageCurrent


rbnVoltageSensorEntry 4


1.3.6.1.4.1.2352.2.4.1.3.1.4

RbnVoltage


Unsigned32

0–50000

Current voltage level at this test point.

1.18.4   rbnCpuTempSensorTable

This table contains one row for each CPU temperature sensor. Each physical entity in the system may have zero or more CPUs. Each of those CPUs that has a temperature sensor, appears here.

Index: entPhysicalIndex, rbnCpuTempIndex

Table 34 describes the attributes in rbnCpuTempSensorTable. All objects in the table are read-only.

Table 34    Objects in rbnCpuTempSensorTable

Object and Object Identifier

Type

Value Range

Description

rbnCpuTempDescr


rbnCpuTempSensorEntry 2


1.3.6.1.4.1.2352.2.4.1.4.1.2

DisplayString

SIZE (0–48)

Description of a CPU temperature test point. Typically an instance of this object holds a user-friendly description of the physical entity and a description of the CPU being monitored by this test point.

rbnCpuTempCurrent


rbnCpuTempSensorEntry 3


1.3.6.1.4.1.2352.2.4.1.4.1.3

RbnTemperature


Unsigned32

0–100

Current temperature of this CPU.

1.18.5   rbnFanSpeedTable

This table contains one row for each fan unit within a fan test point.

Index: rbnFanIndex, rbnFanUnitID

Table 35 describes the attributes in rbnFanSpeedTable. All objects in the table are read-only unless otherwise specified.

Table 35    Objects in rbnFanSpeedTable

Object and Object Identifier

Type

Value Range

Description

rbnFanUnitDescr


rbnFanSpeedEntry 2


1.3.6.1.4.1.2352.2.4.1.5.1.2

DisplayString

SIZE (0–32)

Description of the fan unit within a fan test point.

rbnFanSpeedCurrent


rbnFanSpeedEntry 3


1.3.6.1.4.1.2352.2.4.1.5.1.3

RbnFanSpeed


Unsigned32

N/A

Current speed of this fan unit.

1.19   RBN-FAST-VRRP-MIB

Describes objects used for managing Fast Virtual Router Redundancy Protocol (FVRRP) routers.

1.19.1   rbnFastVrrpOperTable

A table contains rbnFastVrrpOperEntry entries.

Index: ifIndex, rbnFastVrrpOperVrId

Table 36 describes the attributes in rbnFastVrrpOperTable. All objects in the table are read-only.

Table 36    Objects in rbnFastVrrpOperTable

Object and Object Identifier

Type

Value Range

Description

rbnFastVrrpOperVrIdrbnFastVrrpOperEntry 11.3.6.1.4.1.2352.2.45.1.1.1.1

VrIdInteger32

(1...255)

This object contains the Virtual Router Identifier (VRID) of Fast VRRP routers.

rbnFastVrrpOperAdvertisementIntervalrbnFastVrrpOperEntry


21.3.6.1.4.1.2352.2.45.1.1.1.2

Integer32

(100...999) milliseconds

The Fast VRRP advertisement messages time interval in milliseconds. This MIB object is used to replace the standard vrrpOperAdvertisementInterval (seconds) when Fast VRRP is enabled. Either vrrpOperAdvertisementInterval or rbnFastVrrpOperAdvertisementInterval is valid based on the VRRP configurations

1.20   RBN-IP-BIND-MIB

Monitors IP interface binding to physical ports and circuits as they are represented in the IF-MIB.

1.20.1   rbnIpBindTable

A table that shows IP interface bindings to physical ports and circuit encapsulation layers as they are represented in the IF-MIB. This table displays all IP interface bindings in all contexts but is only visible from the local context.

Index: ifIndex, rbnIpBindCircuitHandle

Table 37 describes the attributes in rbnIpBindTable. All objects in the table are read-only.

Table 37    Objects in rbnL2tpTunnelCntTable

Object and Object Identifier

Type

Value Range

Description

rbnIpBindIfIndex


rbnIpBindEntry 2


1.3.6.1.4.1.2352.2.26.1.1.1.2

InterfaceIndexOrZero


Integer32

0–2147483647

If the IP interface is bound to a port, channel, subchannel, or virtual circuit that is included in the IF-MIB, this object contains the ifIndex of that layer; otherwise, this object is set to zero.

rbnIpBindHierarchicalIfIndex


rbnIpBindEntry 3


1.3.6.1.4.1.2352.2.26.1.1.1.3

InterfaceIndexOrZero


Integer32

0–2147483647

If the IP interface is bound to a port, channel, subchannel, or virtual circuit that is not included in the IF-MIB, but that interface is part of a port stack that is included in the IF-MIB, this object contains the ifIndex of the port encapsulation layer that sits on top of that port stack. If the rbnIpBindIfIndex object is set to a nonzero value, this object is set to zero.

rbnIpBindCircuitDescr


rbnIpBindEntry 4


1.3.6.1.4.1.2352.2.26.1.1.1.4

SnmpAdminString

SIZE (0–192)

Descriptive version of the rbnIpBindCircuitHandle object that is consistent with information displayed in the CLI. On the SmartEdge router, this string is formatted as slot/port:channel:subchannel authority/level/index, with the exception that channel and subchannel are only included when appropriate. For example, 4/1 1/2/7, 4/1:1 1/2/7 or 4/1:1:1 1/2/7.

rbnIpBindContextName


rbnIpBindEntry 5


1.3.6.1.4.1.2352.2.26.1.1.1.5

SnmpAdminString

SIZE (0–63)

Name of the context in which this IP interface is defined.

1.21   RBN-IPPOOL-MIB

Provides information that matches the information displayed by the show ip pool falling-threshold command (in any mode).

The following sections contain object information for RBN-IPPOOL-MIB.

1.21.1   IP Pool Per-Context Objects

Table 38 describes the IP pool per-context objects. All objects in the table are read-only.

Table 38    Objects in rbnL2tpTunnelCntTable

Object and Object Identifier

Type

Value Range

Description

rbnIpPoolContextName


rbnIpPoolSummary 1


1.3.6.1.4.1.2352.2.15.1.2.1

SnmpAdminString

SIZE (0–63)

Name of the context containing the IP pool.

rbnIpPoolContextAvailable


rbnIpPoolSummary 2


1.3.6.1.4.1.2352.2.15.1.2.2

Unsigned32

N/A

Total number of IP addresses available in all pools of all interfaces in the context valid in the current view.

rbnIpPoolContextThreshold


rbnIpPoolSummary 3


1.3.6.1.4.1.2352.2.15.1.2.3

Unsigned32

N/A

Per-context threshold of an IP pool is the value for currently available per-context addresses, as reported in the rbnIpPoolContextAvailable object, which causes a trap or log message to be generated when this value is reached. A trap or log message is sent only on a transition of the value of available address from (rbnIpPoolContextThreshold+1) addresses to rbnIpPoolContextThreshold addresses. Additionally, sending of the trap or log message is subject to the values of the rbnIpPoolContextSendTrap object and the rbnIpPoolContextLogMessage object. A value of zero means there is no per-context threshold.

rbnIpPoolContextSendTrap


rbnIpPoolSummary 4


1.3.6.1.4.1.2352.2.15.1.2.4

TruthValue

1—true


2—false

If the value of this object is true, on a per-context threshold crossing event, a trap is sent. See the definition of the rbnIpPoolContextThresholdMet object for the information included in the trap. Both the rbnIpPoolContextSendTrap object and the rbnIpPoolContextLogMessage object can be true at the same time.

rbnIpPoolContextLogMessage


rbnIpPoolSummary 5


1.3.6.1.4.1.2352.2.15.1.2.5

TruthValue

1—true


2—false

If the value of this object is true, on a per-context threshold crossing event, a message is logged. The information contained in the message logged is the same as that included in the rbnIpPoolContextThresholdMet trap. Both the rbnIpPoolContextSendTrap object and the rbnIpPoolContextLogMessage object can be true at the same time.

rbnIpPoolContextTotalSize


rbnIpPoolSummary 6


1.3.6.1.4.1.2352.2.15.1.2.6

Unsigned32

N/A

Total number of IP addresses configured in all pools of all interfaces in the context valid in the current view. The value of this object is the sum of the available addresses plus the unusable addresses.

1.21.2   rbnIpPoolContextThresholdPercentTable

Use this table to monitor the status of per-context IP pool percentage thresholds through SNMP. This table contains the objects that identify information about per-context IP pool thresholds, expressed in percentage. Each row in the table corresponds to one IP pool percentage threshold configured within a particular context. Objects defined in this table are only accessible within the context identified in the SNMP protocol (that is, the community string in SNMPv1 or SNMPv2 or the contextName in SNMPv3).

Index: rbnIpPoolContextThresholdIndex

Table 39 describes the attributes in rbnIpPoolContextThresholdPercentTable. All objects in the table are read-only unless otherwise specified.

Table 39    Objects in rbnIpPoolContextThresholdPercentTable

Object and Object Identifier

Type

Value Range

Description

rbnIpPoolContextThresholdPercentage


rbnIpPoolContextThresholdPercentEntry 2


1.3.6.1.4.1.2352.2.15.1.2.7.1.2

RbnPercentage


Integer32

0–100

Threshold for the percentage of the number of currently available IP pool addresses against the total number of IP pool addresses configured within the context. An SNMP trap or log message is sent only when the current value, which is the percentage of the rbnIpPoolContextAvailable object and the rbnIpPoolContextTotalSize object truncated to a whole number, is less than or equal to this threshold, and the percentage value at the last check was greater than this threshold. Additionally, sending of the SNMP trap or logging a message is subject to the values of the rbnIpPoolContextThresholdSendTrap object and the rbnIpPoolContextThresholdLogMessage object.

rbnIpPoolContextThresholdSendTrap


rbnIpPoolContextThresholdPercentEntry 3


1.3.6.1.4.1.2352.2.15.1.2.7.1.3

TruthValue

1—true


2—false

If the value of this object is true, on a per-context threshold crossing event, an SNMP trap is sent. See the definition of the rbnIpPoolContextThresholdPercentageMet object for the information included in the trap.


The values of both the rbnIpPoolContextThresholdSendTrap object and the rbnIpPoolContextThresholdLogMessage object can be true.

rbnIpPoolContextThresholdLogMessage


rbnIpPoolContextThresholdPercentEntry 4


1.3.6.1.4.1.2352.2.15.1.2.7.1.4

TruthValue

1—true


2—false

If the value of this object is true, on a per-context threshold crossing event, a message is logged. The information contained in the message logged is the same as that included in the rbnIpPoolContextThresholdPercentageMet trap.


The values of both the rbnIpPoolContextThresholdSendTrap object and the rbnIpPoolContextThresholdLogMessage object can be true.

1.21.3   rbnIpPoolTable

Use this table to monitor the status of IP pools on SMS systems through SNMP. This table contains the objects that identify information about IP pools. Each row in the table corresponds to one IP pool for a given interface within a particular context. Objects defined in this table are only accessible within the context identified in the SNMP protocol (that is, the community string in SNMPv1 or SNMPv2 or the contextName in SNMPv3).

Index: rbnIpPoolInterfaceIdx, rbnIpPoolAddr

Table 40 describes the attributes in rbnIpPoolTable. All objects in the table are read-only.

Table 40    Objects in rbnL2tpTunnelCntTable

Object and Object Identifier

Type

Value Range

Description

rbnIpPoolInterfaceName


rbnIpPoolEntry 3


1.3.6.1.4.1.2352.2.15.1.1.1.3

SnmpAdminString

SIZE (0–127)

The name of the interface containing the IP pool.

rbnIpPoolMask


rbnIpPoolEntry 4


1.3.6.1.4.1.2352.2.15.1.1.1.4

IpAddress


String

SIZE (4)

The subnet mask of the IP pool. This object is instantiated for IP pools of type subnet only.

rbnIpPoolSize


rbnIpPoolEntry 5


1.3.6.1.4.1.2352.2.15.1.1.1.5

Unsigned32

N/A

The size of the IP pool is the sum of the available addresses plus the unusable addresses.

rbnIpPoolAvailable


rbnIpPoolEntry 6


1.3.6.1.4.1.2352.2.15.1.1.1.6

Unsigned32

N/A

The number of addresses of an IP pool that are available.

rbnIpPoolUnusable


rbnIpPoolEntry 7


1.3.6.1.4.1.2352.2.15.1.1.1.7

Unsigned32

N/A

Unusable IP addresses in an IP pool, consisting of the IP address of the interface and those used by the network address and the broadcast address of the interface.

rbnIpPoolInuse


rbnIpPoolEntry 8


1.3.6.1.4.1.2352.2.15.1.1.1.8

Unsigned32

N/A

The number of addresses of an IP pool that are in use.

rbnIpPoolThreshold


rbnIpPoolEntry 9


1.3.6.1.4.1.2352.2.15.1.1.1.9

Unsigned32

0–65535

The value of currently available IP addresses, as reported in the rbnIpPoolAvailable object, which causes a trap or log message to be generated when this value is reached. This is a falling threshold, so a trap or log message is sent only on a transition of the value of available address from (rbnIpPoolThreshold+1) addresses to rbnIpPoolThreshold addresses. Additionally, the action of sending the trap or log message is subject to the values of the rbnIpPoolSendTrap object and the rbnIpPoolLogMessage object. A value of zero means there is no threshold.

rbnIpPoolSendTrap


rbnIpPoolEntry 10


1.3.6.1.4.1.2352.2.15.1.1.1.10

TruthValue

1—true


2—false

If true, on reaching a per-pool threshold event, a trap is sent. See the definition of the rbnIpPoolThresholdMet object for the information included in the trap. Both the rbnIpPoolSendTrap object and the rbnIpPoolLogMessage object are allowed to be TRUE at the same time.

rbnIpPoolLogMessage


rbnIpPoolEntry 11


1.3.6.1.4.1.2352.2.15.1.1.1.11

TruthValue

1—true


2—false

If true, on detection of reaching a per-pool threshold event, a message is logged. The information contained in the message is the same as that included in the rbnIpPoolThresholdMet trap. Both the rbnIpPoolSendTrap object and the rbnIpPoolLogMessage object can be true at the same time.

rbnIpPoolName


rbnIpPoolEntry 12


1.3.6.1.4.1.2352.2.15.1.1.1.12

SnmpAdminString

SIZE (0–32)

The name of the IP pool.

rbnIpPoolType


rbnIpPoolEntry 13


1.3.6.1.4.1.2352.2.15.1.1.1.13

Integer

0—subnet


1—range

The type of the IP pool.

rbnIpPoolEndAddr


rbnIpPoolEntry 14


1.3.6.1.4.1.2352.2.15.1.1.1.14

IpAddress


String

SIZE (4)

The end address of the IP pool. This object is instantiated for range IP pools only.

1.22   RBN-L2TP-MIB

Defines the objects used to monitor Layer 2 Tunneling Protocol (L2TP) configuration information.

The following sections describe object information for RBN-L2TP-MIB.

1.22.1   rbnL2tpPeerCfgTable

This table contains objects that you can use to display information about an L2TP Peer.

Index: rbnL2tpMibPeerName

Table 41 describes the attributes for rbnL2tpPeerCfgTable. All objects in the table are read-only unless otherwise specified.

Table 41    Objects in rbnL2tpPeerCfgTable

Object and Object Identifier

Type

Value Range

Description

rbnL2tpPCfgMedia


rbnL2tpPeerCfgEntry 2

String

0–10

Transport media utilized between communicating peers. A media length of 0 means that no transport media type was set. This object is read-create.

rbnL2tpPCfgVendor


rbnL2tpPeerCfgEntry 3

String

0–60

Vendor of L2TP stack running on the remote peer. The length of the string is zero if no vendor name can be obtained from the peer.

rbnL2tpPCfgRev


rbnL2tpPeerCfgEntry 4

Unsigned32

N/A

Firmware revision for the L2TP protocol stack running on the remote peer.

rbnL2tpPCfgHostName


rbnL2tpPeerCfgEntry 5

String

0–255

The name assigned to this peer on the remote host system. A host name length of 0 means that this information could not be obtained from the remote host.

rbnL2tpPCfgRadius


rbnL2tpPeerCfgEntry 6

TruthValue

1—true


2—false

Whether a RADIUS server has been configured for this peer group. A value of true (1) indicates that there is a RADIUS server, it is used for authenticating and authorizing access to a tunnel in this group, and accounting information is sent to the RADIUS server. A value of false (2) indicates that there is no RADIUS server, and authentication and authorization are performed locally.

rbnL2tpPCfgRemIPAddType


rbnL2tpPeerCfgEntry 7

InetAddressType


Integer

0- unknown


1—ipv4


2—ipv6


16—dns

The address type contained in the rbnL2tpPCfgRemIPAdd object.

rbnL2tpPCfgRemIPAdd


rbnL2tpPeerCfgEntry 8

InetAddress


String

SIZE (0–255)

The remote IP address for this tunnel (utilized only with UDP). This object is read-create.

rbnL2tpPCfgStatic


rbnL2tpPeerCfgEntry 9

TruthValue

1—true


2—false

Indicates whether the tunnel is static or dynamic. A value of true (1) means that it is static. A value of (2) indicates that it is dynamic. This object is read-create.

rbnL2tpPCfgLocalIPAddType


rbnL2tpPeerCfgEntry 10

InetAddressType

N/A

Identifies the address type contained in the rbnL2tpPCfgLocalIPAdd object.

rbnL2tpPCfgLocalIPAdd


rbnL2tpPeerCfgEntry 11

InetAddress


String

SIZE (0–255)

The local IP address for this tunnel (utilized only with UDP). This object is read-create.

rbnL2tpPCfgMode


rbnL2tpPeerCfgEntry 12

LacLnsType


Integer

1—other


2—lac


3—lns


4—lacLns

Indicates whether the peer is operating as an LNS, a LAC, or both. This object is read-create.

rbnL2tpPCfgMaxTunnels


rbnL2tpPeerCfgEntry 14

Gauge32

N/A

The maximum number of tunnels that can be configured on this peer. This object is read-create.

rbnL2tpPCfgMaxSesPerTun


rbnL2tpPeerCfgEntry 15

Gauge32

N/A

The maximum number of sessions that can be allocated to one tunnel. This object is read-create.

rbnL2tpPCfgCtlRetranCnt


rbnL2tpPeerCfgEntry 16

Counter32

N/A

The number of times that a control packet was retransmitted.

rbnL2tpPCfgCtlRetranTO


rbnL2tpPeerCfgEntry 17

Unsigned32

0–255

The control retransmit timeout in seconds. This object is read-create.

rbnL2tpPCfgSessAuth


rbnL2tpPeerCfgEntry 18

AuthType


Integer

0—other


1—pap


2—chap


3—chapPap

The session authentication type. This object is read-create.

rbnL2tpPCfgCtlWin


rbnL2tpPeerCfgEntry 19

Gauge32

0–65535

The control window size. This object is read-create.

rbnL2tpPCfgDNIS


rbnL2tpPeerCfgEntry 20

DNISType


Integer

0—other


1—dnis


2—dnisonly

Indicates whether the criteria used for a tunnel switch is Dialed Number Identification String first (a value of (1)), DNIS only (a value of (2)) or that no preference has been set (a value of (0)). This object is read-create.

rbnL2tpPCfgPoliceRate


rbnL2tpPeerCfgEntry 21

Unsigned32

N/A

The received aggregate stream limit, in kilobits per second (kbps). This object is read-create.

rbnL2tpPCfgPoliceBurst


rbnL2tpPeerCfgEntry 22

Unsigned32

N/A

The packet burst tolerance for tunnels received by this peer group. This object is read-create.

rbnL2tpPCfgLimitRate


rbnL2tpPeerCfgEntry 23

Unsigned32

N/A

The limit of the aggregate packet stream transmitted through a tunnel in kpbs. This object is read-create.

rbnL2tpPCfgLimitBurst


rbnL2tpPeerCfgEntry 24

Unsigned32

N/A

The packet burst tolerance limit transmitted on a tunnel. This object is read-create.

rbnL2tpPCfgGroup


rbnL2tpPeerCfgEntry 25

SnmpAdminString

N/A

The L2TP group assigned to this peer. Each peer configuration can be assigned only one tunnel group. A length of 0 means that the group name was not assigned.

rbnL2tpPCfgPref


rbnL2tpPeerCfgEntry 26

Unsigned32

N/A

The RADIUS-based preference number (used by tunnel groups only). A lower number indicates a higher preference. This object is read-create.

rbnL2tpPCfgPasswd


rbnL2tpPeerCfgEntry 27

SnmpAdminString

0–20

The password used for this account when performing the connection handshake protocol with the remote host. A length of 0 indicates that no password has been assigned. This object is read-create.

rbnL2tpPCfgHelloTimer


rbnL2tpPeerCfgEntry 28

Unsigned32

0–3600

The interval (in seconds) in which Hello (or keepalive) packets are sent by local tunnels belonging to this tunnel configuration. This object is read-create.

rbnL2tpPCfgRecQue


rbnL2tpPeerCfgEntry 29

TruthValue

1—true


2—false

Indicates whether there is receive queueing of out-of-sequence messages. A value of true (1) indicates that the messages are queued.

rbnL2tpPCfgSessContext


rbnL2tpPeerCfgEntry 30

SnmpAdminString

SIZE (0–80)

The name of the session context. A size of 0 indicates that the context could not be determined. Any context name length greater than 80 is truncated. This object holds a value for PPPoE only. This object is read-create.

rbnL2tpPCfgSessService


rbnL2tpPeerCfgEntry 31

SnmpAdminString

SIZE (0–20)

The service group to which this session belongs. A length of 0 indicates that no service group was assigned. This object is read-create.

rbnL2tpPCfgEthEncap


rbnL2tpPeerCfgEntry 32

EthEncapType


Integer

0—other


1—ethPpoe


2—ethMulti


3—ethernet

The Ethernet encapsulation type. This object is read-create.

rbnL2tpPCfgEthSession


rbnL2tpPeerCfgEntry 33

SnmpAdminString

SIZE (0–20)

The Ethernet session of which this is a part. This object is set only for non-PPPoE sessions; otherwise, it has a zero length. This object is read-create.

rbnL2tpPCfgTunnelCount


rbnL2tpPeerCfgEntry 34

Counter32

N/A

The number of tunnels that are active for this peer configuration. This object is read-create.

rbnL2tpPCfgTunCtlErrs


rbnL2tpPeerCfgEntry 35

Counter32

N/A

The number of tunnel control errors encountered by tunnels connected to this peer.

rbnL2tpPCfgSessionCount


rbnL2tpPeerCfgEntry 36

Counter32

N/A

The of sessions that are part of this peer.

1.22.2   rbnL2tpTunnelCfgTable

This table contains objects related to L2TP Tunnel information.

Index: rbnL2tpMibTunnelID

Table 42 describes the attributes for rbnL2tpTunnelCfgTable, L2TP Peer Information Table. All objects in the table are read-only.

Table 42    Objects in rbnL2tpPeerCfgTable

Object and Object Identifier

Type

Value Range

Description

rbnL2tpTCfgTunnelNm


rbnL2tpTunnelCfgEntry 2


1.3.6.1.4.1.2352.2.28.1.2.1.2

SnmpAdminString

SIZE (1–80)

The local name of the tunnel.

rbnL2tpTCfgPeerName


rbnL2tpTunnelCfgEntry 3


1.3.6.1.4.1.2352.2.28.1.2.1.3

SnmpAdminString

SIZE (1–80)

The remote peer to which this tunnel is connected.

rbnL2tpTCfgTunCtlErrs


rbnL2tpTunnelCfgEntry 4


1.3.6.1.4.1.2352.2.28.1.2.1.4

Counter32

N/A

The number of tunnel control errors encountered by this tunnel.

rbnL2tpTCfgLastCtlErr


rbnL2tpTunnelCfgEntry 5


1.3.6.1.4.1.2352.2.28.1.2.1.5

CtlErrType

N/A

The value of the last control error.

rbnL2tpTCfgLastCErrTime


rbnL2tpTunnelCfgEntry 6


1.3.6.1.4.1.2352.2.28.1.2.1.6

DateAndTime

N/A

The time of the last control error.

rbnL2tpTCfgTunDataErrs


rbnL2tpTunnelCfgEntry 7


1.3.6.1.4.1.2352.2.28.1.2.1.7

Counter32

N/A

The number of tunnel data errors.

rbnL2tpTCfgLastDataErr


rbnL2tpTunnelCfgEntry 8


1.3.6.1.4.1.2352.2.28.1.2.1.8

Unsigned32

N/A

The value of the last tunnel data error.

rbnL2tpTCfgLastDErrTime


rbnL2tpTunnelCfgEntry 9


1.3.6.1.4.1.2352.2.28.1.2.1.9

DateAndTime

N/A

The time of the last tunnel data error.

rbnL2tpTCfgSessionCount


rbnL2tpTunnelCfgEntry 10


1.3.6.1.4.1.2352.2.28.1.2.1.10

Gauge32

N/A

The number of sessions belonging to this tunnel.

rbnL2tpTCfgTotActSessions


rbnL2tpTunnelCfgEntry 11


1.3.6.1.4.1.2352.2.28.1.2.1.11

Counter32

N/A

The total number of sessions that, at some time, reached the established state.

rbnL2tpTCfgActSessCnt


rbnL2tpTunnelCfgEntry 12


1.3.6.1.4.1.2352.2.28.1.2.1.12

Gauge32

N/A

The total number of sessions that are presently in the established state.

rbnL2tpTCfgTotFailSessions


rbnL2tpTunnelCfgEntry 13


1.3.6.1.4.1.2352.2.28.1.2.1.13

Counter32

N/A

The number of sessions that failed to reach the established state.

rbnL2tpMibTunnelState


rbnL2tpTunnelCfgEntry 14


1.3.6.1.4.1.2352.2.28.1.2.1.14

TunStateType

N/A

The current state of the tunnel.

rbnL2tpTCfgRemoteTunnelID


rbnL2tpTunnelCfgEntry 15


1.3.6.1.4.1.2352.2.28.1.2.1.15

Unsigned32

0–65535

The remote tunnel ID. A value of zero indicates that the remote tunnel ID could not be determined.

rbnL2tpTCfgTunnelContext


rbnL2tpTunnelCfgEntry 16


1.3.6.1.4.1.2352.2.28.1.2.1.16

SnmpAdminString

SIZE (0–80)

Identifies the context of this tunnel. The empty context name (zero length) indicates that the context could not be determined. Any context name length greater than 80 is truncated.

1.22.3   rbnL2tpPeerCntTable

This table contains objects related to the L2TP Peer Statistics Table.

Index: IMPLIED rbnL2tpMibPeerName

Table 43 describes the attributes for rbnL2tpPeerCntTable. All objects in the table are read-only.

Table 43    Objects in rbnL2tpPeerCntTable

Object and Object Identifier

Type

Value Range

Description

rbnL2tpPCDataPktSent


rbnL2tpPeerCntEntry 1

Counter32

N/A

A count of the total number of data packets sent through tunnels that are part of this group to the L2TP peer.

rbnL2tpPCDataPktRx


rbnL2tpPeerCntEntry 2

Counter32

N/A

A count of the total number of data packets received through tunnels that are part of this group from the L2TP peer.

rbnL2tpPCDataByteSent


rbnL2tpPeerCntEntry 3

Counter32

N/A

Count of the total number of data bytes sent through tunnels that are part of this group to the L2TP peer.

rbnL2tpPCDataByteRx


rbnL2tpPeerCntEntry 4

Counter32

N/A

A count of the total number of data bytes received through tunnels that are part of this group from the L2TP peer.

rbnL2tpPCCtlPktSent


rbnL2tpPeerCntEntry 5

Counter32

N/A

A count of the total number of control packets sent through tunnels that are part of this group to the L2TP peer.

rbnL2tpPCCtlPktRx


rbnL2tpPeerCntEntry 6

Counter32

N/A

A count of the total number of control packets received through tunnels that are a part of this group from the L2TP peer.

rbnL2tpPCCtlByteSent


rbnL2tpPeerCntEntry 7

Counter32

N/A

A count of the total number of control bytes sent through tunnels that are a part of this group to the L2TP peer.

rbnL2tpPCCtlByteRx


rbnL2tpPeerCntEntry 8

Counter32

N/A

A count of the total number of control bytes received through tunnels that are a part of this group from the L2TP peer.

rbnL2tpPCPolicePktDrop


rbnL2tpPeerCntEntry 9

Counter32

N/A

The total number of packets received from L2TP peers of tunnels that are a part of this group that were dropped.

rbnL2tpPCRatePktDrop


rbnL2tpPeerCntEntry 10

Counter32

N/A

The total number of packets transmitted to the L2TP peers of tunnels in this group that were dropped.

rbnL2tpPCTxSCCRQCnt


rbnL2tpPeerCntEntry 11

Counter32

N/A

A count of the SCCRQ transmits for this group.

rbnL2tpPCRxSCCRQCnt


rbnL2tpPeerCntEntry 12

Counter32

N/A

A count of the received SCCRQs for this group.

rbnL2tpPCActTunnels


rbnL2tpPeerCntEntry 13

Gauge32

N/A

The number of the active tunnels for this group.

rbnL2tpPCTunnelCtlErr


rbnL2tpPeerCntEntry 14

Counter32

N/A

The total number of tunnel control errors for all of the tunnels that are a part of this group.

rbnL2tpPCSessionCount


rbnL2tpPeerCntEntry 15

Gauge32

N/A

The total number of sessions for this group.

rbnL2tpPCTunnelDataErr


rbnL2tpPeerCntEntry 16

Counter32

N/A

The total number of tunnel data errors reported by members of this group.

1.22.4   rbnL2tpTunnelCntTable

This table contains objects related to L2TP tunnel statistics.

Index: rbnL2tpMibTunnelID

Table 44 describes the attributes for rbnL2tpTunnelCntTable. All objects in the table are read-only.

Table 44    Objects in rbnL2tpTunnelCntTable

Object and Object Identifier

Type

Value Range

Description

rbnL2tpTCDataPktSent


rbnL2tpTunnelCntEntry 1

Counter32

N/A

The number of data packets sent from this platform through this tunnel to its peer.

rbnL2tpTCDataPktRcvd


rbnL2tpTunnelCntEntry 2

Counter32

N/A

The number of packets received from the L2TP peer for this tunnel.

rbnL2tpTCDataByteSent


rbnL2tpTunnelCntEntry 3

Counter32

N/A

The number of data bytes sent from this platform through this tunnel to its peer.

rbnL2tpTCDataByteRcvd


rbnL2tpTunnelCntEntry 4

Counter32

N/A

The number of data bytes received from the L2TP peer for this tunnel.

rbnL2tpTCCntrlPktSent


rbnL2tpTunnelCntEntry 5

Counter32

N/A

The number of control packets sent from this platform through this tunnel to its L2TP peer.

rbnL2tpTCCntrlPktRcvd


rbnL2tpTunnelCntEntry 6

Counter32

N/A

The number of control packets received from the L2TP peer for this tunnel.

rbnL2tpTCCntrlByteSent


rbnL2tpTunnelCntEntry 7

Counter32

N/A

The number of control bytes sent from this platform through this tunnel to its L2TP peer.

rbnL2tpTCCntrlByteRcvd


rbnL2tpTunnelCntEntry 8

Counter32

N/A

The number of control bytes received from the L2TP peer of this tunnel.

rbnL2tpTCPolicePktDrop


rbnL2tpTunnelCntEntry 9

Counter32

N/A

The number of packets received from the L2TP peer of this tunnel that were dropped.

rbnL2tpTCRatePktDrop


rbnL2tpTunnelCntEntry 10

Counter32

N/A

The number of packets transmitted from this platform through this tunnel that were dropped.

rbnL2tpTCCntrlErr


rbnL2tpTunnelCntEntry 11

Unsigned32

N/A

The number of control errors that were detected.

rbnL2tpTCLastCtlErr


rbnL2tpTunnelCntEntry 12

CtlErrType

N/A

The last control error for this tunnel that was detected.

rbnL2tpTCLastCtlErrTime


rbnL2tpTunnelCntEntry 13

DateAndTime

N/A

The time that the last control error for this tunnel was detected.

rbnL2tpTCMaxResendQ


rbnL2tpTunnelCntEntry 14

Gauge32

N/A

The maximum length of the resend queue.

rbnL2tpTCMaxUnsentQ


rbnL2tpTunnelCntEntry 15

Gauge32

N/A

The maximum length of the unsent queue.

rbnL2tpTCCurResendQ


rbnL2tpTunnelCntEntry 16

Gauge32

N/A

The current length of the resend queue.

rbnL2tpTCCurUnsentQ


rbnL2tpTunnelCntEntry 17

Gauge32

N/A

The current length of the unsent queue.

rbnL2tpTCCurWindow


rbnL2tpTunnelCntEntry 18

Gauge32

N/A

The current window size.

1.22.5   rbnL2tpSessionCntTable

This table contains objects related to L2TP Statistics.

Index: rbnL2tpMibTunnelID, rbnL2tpMibSessionID

Table 45 describes the attributes for rbnL2tpSessionCntTable. All objects in the table are read-only.

Table 45    Objects in rbnL2tpSessionCntTable

Object and Object Identifier

Type

Value Range

Description

rbnL2tpSCPktSent


rbnL2tpSessionCntEntry 2

Counter32

N/A

The number of packets sent by this platform in this session.

rbnL2tpSCPktRcvd


rbnL2tpSessionCntEntry 3

Counter32

N/A

The number of packets received by this platform in this session.

rbnL2tpSCByteSent


rbnL2tpSessionCntEntry 4

Counter32

N/A

The number of bytes sent by this platform in this session.

rbnL2tpSCByteRcvd


rbnL2tpSessionCntEntry 5

Counter32

N/A

The number of bytes received by this platform in this session.

rbnL2tpSCMcastPktSent


rbnL2tpSessionCntEntry 6

Counter64

N/A

The number of multicast packets sent by this platform in this session.

rbnL2tpSCMcastPktRcvd


rbnL2tpSessionCntEntry 7

Counter64

N/A

The number of multicast packets received by this platform in this session.

rbnL2tpSCMcastByteSent


rbnL2tpSessionCntEntry 8

Counter64

N/A

The number of multicast bytes sent by this platform in this session.

rbnL2tpSCMcastByteRcvd


rbnL2tpSessionCntEntry 9

Counter64

N/A

The number of multicast bytes received by this platform in this session.

1.22.6   rbnL2tpPeerTunCfgTable

This table contains objects which identify L2TP peers and tunnels.

Index: rbnL2tpMibPeerName, rbnL2tpMibTunnelID

Table 46 describes the attributes for rbnL2tpPeerTunCfgTable. All objects in the table are read-only.

Table 46    Objects in rbnL2tpPeerTunCfgTable

Object and Object Identifier

Type

Value Range

Description

rbnL2tpPTCfgTunnelRemoteID


rbnL2tpPeerTunCfgEntry 1


1.3.6.1.4.1.2352.2.28.1.8.1.1

Unsigned32

0–65535

The remote tunnel ID. A value of zero indicates that the remote tunnel ID could not be determined.

rbnL2tpPTCfgTunnelLocalNm


rbnL2tpPeerTunCfgEntry 2


1.3.6.1.4.1.2352.2.28.1.8.1.2

SnmpAdminString

SIZE (0–80)

The local name that was given to this tunnel. The length of the string is zero if no local name assigned to the tunnel.

rbnL2tpPTCfgTunnelRemoteNm


rbnL2tpPeerTunCfgEntry 3


1.3.6.1.4.1.2352.2.28.1.8.1.3

SnmpAdminString

SIZE (1–80)

The name that was given to the remote end of this tunnel. The length of the string is zero if no tunnel name can be obtained from the peer.

rbnL2tpPTCfgPeerLocalNm


rbnL2tpPeerTunCfgEntry 4


1.3.6.1.4.1.2352.2.28.1.8.1.4

SnmpAdminString

SIZE (0–80)

The local peer name. The empty peer name (zero length) indicates that the name could not be determined.

rbnL2tpPTCfgTunnelRemoteIPAddrType


rbnL2tpPeerTunCfgEntry 5


1.3.6.1.4.1.2352.2.28.1.8.1.5

InetAddressType


Integer

0—unknown


1—ipv4


2—ipv6


16—dns

The address type contained in the rbnL2tpPTCfgTunnelRemoteIPAddr object.

rbnL2tpPTCfgTunnelRemoteIPAddr


rbnL2tpPeerTunCfgEntry 6


1.3.6.1.4.1.2352.2.28.1.8.1.6

InetAddress


String

SIZE (0–255)

The remote IP address for this tunnel (utilized only with UDP).

rbnL2tpPTCfgTunnelState


rbnL2tpPeerTunCfgEntry 7


1.3.6.1.4.1.2352.2.28.1.8.1.7

TunStateType

N/A

The current state of the tunnel.

rbnL2tpPTCfgTunnelContext


rbnL2tpPeerTunCfgEntry 8


1.3.6.1.4.1.2352.2.28.1.8.1.8

SnmpAdminString

SIZE (0–80)

The context of this tunnel. The empty context name (zero length) indicates that the context could not be determined. Any context name length greater than 80 is truncated.

rbnL2tpPTCfgSessionCount


rbnL2tpPeerTunCfgEntry 9


1.3.6.1.4.1.2352.2.28.1.8.1.9

Gauge32

N/A

The number of sessions belonging to this tunnel.

rbnL2tpPTCfgActSessCnt


rbnL2tpPeerTunCfgEntry 10


1.3.6.1.4.1.2352.2.28.1.8.1.10

Gauge32

N/A

The total number of sessions that are presently in the established state.

rbnL2tpPTCfgTotActSessions


rbnL2tpPeerTunCfgEntry 11


1.3.6.1.4.1.2352.2.28.1.8.1.11

Counter32

N/A

The total number of sessions that, at some time, reached the established state.

rbnL2tpPTCfgTotFailSessions


rbnL2tpPeerTunCfgEntry 12


1.3.6.1.4.1.2352.2.28.1.8.1.12

Counter32

N/A

The number of sessions that failed to reach the established state.

1.23   RBN-L2VPN-MIB

Provides data that matches the information displayed when entering the show l2vpn command (in any mode) using the xc option.

The following sections describe object information for RBN-L2VPN-MIB.

1.23.1   rbnMplsL2VpnStaticTable

This table contains objects that identify static Layer 2 VPN circuits. Rows in this table are created or deleted when the VPN circuit is configured.

Index: rbnMplsL2VpnStaticPeerAddr, rbnMplsL2VpnStaticVpnLabel

Table 47 describes the attributes in rbnMplsL2VpnStaticTable.

Table 47    Objects in rbnMplsL2VpnStaticTable

Object and Object Identifier

Type

Value Range

Description

rbnMplsL2VpnStaticVpnLabel


rbnMplsL2VpnStaticEntry 1


1.3.6.1.4.1.2352.2.39.3.3.1.1

Unsigned32

(4096..65535)

This object indicates the unique value assigned to a particular 548 static VPN circuit."

rbnMplsL2VpnStaticPeerAddr


rbnMplsL2VpnStaticEntry 2


1.3.6.1.4.1.2352.2.39.3.3.1.2

IpAddress

 

This object indicates the ip address of the VPN peer.

rbnMplsL2VpnStaticCctHandle


rbnMplsL2VpnStaticEntry 3

1.3.6.1.4.1.2352.2.39.3.3.1.3

RbnCircuitHandle


Octet String

SIZE (8)

The internal representation of the physical circuit to which this VPN is connected. A hexidecimal value of ff ff ff ff ff ff ff ff indicates an invalid circuit.

rbnMplsL2VpnStaticVpnCctHandle


rbnMplsL2VpnStaticEntry 4


1.3.6.1.4.1.2352.2.39.3.3.1.4

RbnCircuitHandle


Octet String

SIZE (8)

The internal representation of the VPN pseudo-circuit.

rbnMplsL2VpnStaticExpBits


rbnMplsL2VpnStaticEntry 5


1.3.6.1.4.1.2352.2.39.3.3.1.5

Unsigned32

N/A

The number of EXP bits configured for this VPN circuit.

rbnMplsL2VpnStaticInputCctUp


rbnMplsL2VpnStaticEntry 6


1.3.6.1.4.1.2352.2.39.3.3.1.6

TruthValue

1—true


2—false

The status of the VPN attachment circuit. A value of true indicates that the VPN attachment circuit is connected with its remote site. A value of false indicates that the remote site is not presently connected.

rbnMplsL2VpnStaticXcFlags


rbnMplsL2VpnStaticEntry 7


1.3.6.1.4.1.2352.2.39.3.3.1.7

RbnVpnXcFlagsType

0—none


2—deletingSignal


3—deletingConfig


4—inLblmap


5—updating


6—up


7—inLdp


8—fromLdp


9—fromConfig


10—stale


11—expSet


12—ismUp


13—peerUp


14—remoteEncap


15—localCbit


16—remoteCbit

Indicates more detailed information on the status of the VPN circuit. This object is a bit field, so it may contain one or more of these values.

rbnMplsL2VpnStaticIfIndexOrZero


rbnMplsL2VpnStaticEntry 8


1.3.6.1.4.1.2352.2.39.3.3.1.8

InterfaceIndexOrZero


Integer32

0–2147483647

Indicates whether there is a corresponding entry in ifTable. A nonzero value indicates the ifIndex of the entry in ifTable. A value of zero indicates that there is no entry.

1.23.2   rbnMplsL2VpnLdpTable

This table contains objects that identify Layer Distribution Protocol Layer 2 VPN circuits. Rows in this table are created or deleted when the VPN circuit is configured.

Index: rbnMplsL2VpnLdpPeerAddr, rbnMplsL2VpnLdpVcId

Table 48 describes the attributes in rbnMplsL2VpnLdpTable.

Table 48    Objects in rbnMplsL2VpnLdpTable

Object and Object Identifier

Type

Value Range

Description

rbnMplsL2VpnLdpVcId


rbnMplsL2VpnLdpEntry 1


1.3.6.1.4.1.2352.2.39.3.4.1.1

Unsigned32

(0..4294967295)

This object indicates the unique virtual VPN circuit id assigned 675 to this circuit.

rbnMplsL2VpnLdpPeerAddr


rbnMplsL2VpnLdpEntry 2


1.3.6.1.4.1.2352.2.39.3.4.1.2

IpAddress

 

This object indicates the ip address if the VPN peer.

rbnMplsL2VpnLdpCctHandle


rbnMplsL2VpnLdpEntry 3


1.3.6.1.4.1.2352.2.39.3.4.1.3

RbnCircuitHandle


Octet String

SIZE (8)

The internal representation of the physical circuit to which this VPN is connected. A hexidecimal value of ff ff ff ff ff ff ff ff indicates an invalid circuit.

rbnMplsL2VpnLdpVpnCctHandle


rbnMplsL2VpnLdpEntry 4


1.3.6.1.4.1.2352.2.39.3.4.1.4

RbnCircuitHandle


Octet String

SIZE (8)

The internal representation of the VPN pseudo-circuit.

rbnMplsL2VpnLdpInLabel


rbnMplsL2VpnLdpEntry 5


1.3.6.1.4.1.2352.2.39.3.4.1.5

Unsigned32

N/A

The value used by the remote connection to identify this VPN circuit when communicating with the local manager.

rbnMplsL2VpnLdpVpnLabel


rbnMplsL2VpnLdpEntry 6


1.3.6.1.4.1.2352.2.39.3.4.1.6

Unsigned32

N/A

The value setup in the local configuration to identify this VPN circuit.

rbnMplsL2VpnLdpRemGrpId


rbnMplsL2VpnLdpEntry 7


1.3.6.1.4.1.2352.2.39.3.4.1.7

Unsigned32

N/A

The remote group of which this VPN circuit is a part.

rbnMplsL2VpnLdpLocEncap


rbnMplsL2VpnLdpEntry 8


1.3.6.1.4.1.2352.2.39.3.4.1.8

SnmpAdminString

SIZE (0–80)

The local encapsulation type associated with this VPN circuit.

rbnMplsL2VpnLdpRemEncap


rbnMplsL2VpnLdpEntry 9


1.3.6.1.4.1.2352.2.39.3.4.1.9

SnmpAdminString

SIZE (0–80)

The remote encapsulation type associated with this VPN circuit.

rbnMplsL2VpnLdpLocVcType


rbnMplsL2VpnLdpEntry 10


1.3.6.1.4.1.2352.2.39.3.4.1.10

RbnVpnVcType


Integer

0—unknown


1—frame


2—aal5


3—atmTransCell


4—vlan


5—ethernet


6—hdlc


7—ppp


8—cem


9—atmVccCell


10—atmVpcCell

The type of virtual circuit on the local system.

rbnMplsL2VpnLdpRemVcType


rbnMplsL2VpnLdpEntry 11


1.3.6.1.4.1.2352.2.39.3.4.1.11

RbnVpnVcType


Integer

0—unknown


1—frame


2—aal5


3—atmTransCell


4—vlan


5—ethernet


6—hdlc


7—ppp


8—cem


9—atmVccCell


10—atmVpcCell

The type of virtual circuit on the remote system.

rbnMplsL2VpnLdpLocMtu


rbnMplsL2VpnLdpEntry 12


1.3.6.1.4.1.2352.2.39.3.4.1.12

Unsigned32

N/A

The maximum transmission unit of the local VPN circuit.

rbnMplsL2VpnLdpRemMtu


rbnMplsL2VpnLdpEntry 13


1.3.6.1.4.1.2352.2.39.3.4.1.13

Unsigned32

N/A

The maximum transmission unit of the remote connection.

rbnMplsL2VpnLdpXcCctUp


rbnMplsL2VpnLdpEntry 14


1.3.6.1.4.1.2352.2.39.3.4.1.14

TruthValue

1—true


2—false

The status of the VPN cross-connect circuit. A value of true indicates that the VPN circuit is connected with its remote site and attachment circuit is up (rbnMplsL2VpnLdpInputCctUp is true). A value of false indicates that the remote site is not connected, , this mean that either the PSN is not reachable or the attachment circuit is down or signaling parameters mismatched.

rbnMplsL2VpnLdpExpBits


rbnMplsL2VpnLdpEntry 15


1.3.6.1.4.1.2352.2.39.3.4.1.15

Unsigned32

N/A

The number of EXP bits configured for this VPN circuit.

rbnMplsL2VpnLdpInputCctUp


rbnMplsL2VpnLdpEntry 16


1.3.6.1.4.1.2352.2.39.3.4.1.16

TruthValue

1—true


2—false

The status of the VPN attachment circuit. A value of true indicates that the VPN attachment circuit is up. A value of false indicates that the remote site is down.

rbnMplsL2VpnLdpXcFlags


rbnMplsL2VpnLdpEntry 17


1.3.6.1.4.1.2352.2.39.3.4.1.17

RbnVpnXcFlagsType

0—none


2—deletingSignal


3—deletingConfig


4—inLblmap


5—updating


6—up


7—inLdp


8—fromLdp


9—fromConfig


10—stale


11—expSet


12—ismUp


13—peerUp


14—remoteEncap


15—localCbit


16—remoteCbit

More detailed information on the status of the VPN circuit. This object is a bit field, so it may contain one or more of these values.

rbnMplsL2VpnLdpIfIndexOrZero


rbnMplsL2VpnLdpEntry 18


1.3.6.1.4.1.2352.2.393.4.1.18

InterfaceIndexOrZero


Integer32

0–2147483647

Indicates whether there is a corresponding entry in ifTable. A nonzero value indicates the ifIndex of the entry in ifTable. A value of zero indicates that there is no entry.

1.24   RBN-MEMORY-MIB

Manages system memory usage.

The following sections describe object information for RBN-MEMORY-MIB.

1.24.1   rbnMemoryTable

This table contains the objects that identify information about memory usage.

Index: rbnMemoryIndex

Table 49 describes the attributes in rbnMemoryTable. All objects in the table are read-only.

Table 49    Objects in rbnMemoryTable

Object and Object Identifier

Type

Value Range

Description

rbnMemoryModule


rbnMemoryEntry 2


1.3.6.1.4.1.2352.2.16.1.2.1.2

SnmpAdminString

SIZE (0–32)

The name of the module on which this memory resides.

rbnMemoryFreeKBytes


rbnMemoryEntry 3


1.3.6.1.4.1.2352.2.16.1.2.1.3

RbnPercentage


Integer32

0–100

The size of unused memory in this entry.

rbnMemoryKBytesInUse


rbnMemoryEntry 4


1.3.6.1.4.1.2352.2.16.1.2.1.4

RbnPercentage


Integer32

0–100

The size of memory in use in this entry.

rbnMemoryBlocksInUse


rbnMemoryEntry 5


1.3.6.1.4.1.2352.2.16.1.2.1.5

Unsigned32

0– 4294967295

The number of blocks of memory on this module in use.


You can use this statistic to check for memory leaks. For example, you can note the value, do some operations, undo the operations, then check the value again. The start and end values should match. If they do not, there may be a memory leak.

rbnMemoryCumulBlocks


rbnMemoryEntry 6


1.3.6.1.4.1.2352.2.16.1.2.1.6

Unsigned3

0– 4294967295

The cumulative blocks count for this entry. In some systems, this count indicates how many times the system called the memory allocation routine since the system booted.


You can use this object to measure the how much memory an operation uses by measuring the number times the system calls the memory allocation routine.

1.25   RBN-MPLS-L3VPN-STD-EXT-MIB

This MIB contains managed object definitions for the Layer 3 MPLS VPNs.

The following section describes object information for RBN-MPLS-L3VPN-STD-EXT-MIB.

1.25.1   rbnMplsL3VpnVrfRTTable

This table specifies per-VRF route target association. Each entry identifies a connectivity policy supported as part of a VPN. rbnMplsL3VpnVrfRTTable is equivalent to mplsL3VpnVrfRTTable in MPLS-L3VPN-STD-MIB except for lexicographical ordering. An entry in this table is created by an LSR for each route target configured for a VRF supporting an MPLS L3VPN instance. The indexing provides ordering per VRF instance. See RFC 4364, BGP/MPLS IP Virtual Private Networks (VPNs) for a complete definition of a route target.

Index: mplsL3VpnVrfName, rbnMplsL3VpnVrfRTAddrFamily, rbnMplsL3VpnVrfRTType, rbnMplsL3VpnVrfRTIndex

Table 50 describes the attributes in rbnMplsL3VpnVrfRTTable. All objects in the table are not accessible unless stated otherwise.

Table 50    Objects in rbnMplsL3VpnVrfRTTable

Object and Object Identifier

Type

Value Range

Description

mplsL3VpnVrfName


MPLS-L3VPN-STD-MIB


mplsL3VpnVrfEntry 1


1.3.6.1.2.1.10.166.11.1.2.2.1.1

MplsL3VpnName


OCTET STRING

SIZE (0..31)

The human-readable name of this VPN. This may be equivalent to the VPN-ID identified in RFC2685, Virtual Private Networks Identifier, but may also vary. If it is set to the VPN ID, it must be equivalent to the value of mplsL3VpnVrfVpnId. It is strongly recommended that all sites supporting VRFs that are part of the same VPN use the same naming convention for VRFs as well as the same VPN ID.

rbnMplsL3VpnVrfRTAddrFamily


rbnMplsL3VpnVrfRTEntry 1


1.3.6.1.4.1.2352.2.51.1.1.1.1.1

AddressFamilyNumbers

1—ipV4


2— ipV6

The address family in which the route target is declared.

rbnMplsL3VpnVrfRTType


rbnMplsL3VpnVrfRTEntry 2


1.3.6.1.4.1.2352.2.51.1.1.1.1.2

MplsL3VpnRtType


INTEGER

1—import


2—export

The route target distribution type.

rbnMplsL3VpnVrfRTIndex


rbnMplsL3VpnVrfRTEntry 3


1.3.6.1.4.1.2352.2.51.1.1.1.1.3

Unsigned32

1..4294967295

Auxiliary index for route targets configured for a particular VRF.

rbnMplsL3VpnVrfRT


rbnMplsL3VpnVrfRTEntry 4


1.3.6.1.4.1.2352.2.51.1.1.1.1.4

MplsL3VpnRouteDistinguisher


OCTET STRING

SIZE (0..256)

The route target distribution policy. This object is read-only.

rbnMplsL3VpnVrfRTDescr


rbnMplsL3VpnVrfRTEntry 5


1.3.6.1.4.1.2352.2.51.1.1.1.1.5

SnmpAdminString


OCTET STRING

SIZE (0..255)

Description of the route target. This object is read-only.

1.26   RBN-NOTIFY-ENHANCE-MIB

Enhances the notification objects on devices.

1.26.1   RBN-NOTIFY-ENHANCE-MIB Objects

Table 51 describes the general objects in RBN-NOTIFY-MIB. All objects in the table are accessible-for-notify.

Table 51    Objects in rbnL2tpTunnelCntTable

Object and Object Identifier

Type

Value Range

Description

rbnNESlot


rbnNEGeneral 1


1.3.6.1.4.1.2352.2.36.1.1.1

RbnSlot


Unsigned32

(0–255)

Represents the chassis slot number in which the entity associated with the notification is contained. A value of '0' indicates that the entity is not contained in a chassis slot.

rbnNECardName


rbnNEGeneral 2


1.3.6.1.4.1.2352.2.36.1.1.2

DisplayString

SIZE (0–255)

A textual description of the traffic card associated with the notification.

rbnNECardOp


rbnNEGeneral 3


1.3.6.1.4.1.2352.2.36.1.1.3

Integer

1—insert


2—remove


3—other

Represents the operation performed on the traffic card associated with the notification.

rbnNECircuitId


rbnNEGeneral 4


1.3.6.1.4.1.2352.2.36.1.1.4

DisplayString

SIZE (0–255)

Represents a string that identifies the circuit associated with the notification. On the SmartEdge router, this string is formatted as slot-port-channel-subchannel, channel and subchannel are only included when appropriate.

1.27   RBN-PRODUCT-MIB

Contains the administrative assignments which are used to uniquely identify physical components.

1.27.1   RBN-PRODUCT-MIB Objects

Table 52 describes objects in RBN-PRODUCT-MIB.

Table 52    Objects in RBN-PRODUCT-MIB

Object and Object Identifier

Value Range

Type

Description

rbnEntModuleSE20PortGIGE


rbnEntityTypeModule 72


1.3.6.1.4.1.2352.6.9.72

N/A

N/A

The definitive identifier for the 20-port PPA3- or PMA3-based Gigabit Ethernet media interface connect module

rbnEntModuleSE4Port10GIGE


rbnEntityTypeModule 73


1.3.6.1.4.1.2352.6.9.73

N/A

N/A

The definitive identifier for the 4-port PPA3- or PMA3-based 10 Gigabit Ethernet media interface connect module

rbnEntModuleSE10GIGETM


rbnEntityTypeModule 74


1.3.6.1.4.1.2352.6.9.74

N/A

N/A

The definitive identifier for the SmartEdge 10 Gigabit Ethernet traffic management interface module

rbnEntPortSE10GIGETM


rbnEntityTypePort 69


1.3.6.1.4.1.2352.6.10.69

N/A

N/A

The definitive identifier for the SmartEdge 10 Gigabit Ethernet traffic management interface port

rbnEntityTypeFan


rbnEntities 7


1.3.6.1.4.1.2352.6.7

N/A

N/A

The top-level category identifier for entities that reside in the value of the PhysicalClass ENTITY-MIB object as *fan*

rbnEntModuleSEAIMOC12E


rbnEntityTypeModule 58


1.3.6.1.4.1.2352.6.9.58

N/A

N/A

The definitive identifier for the SmartEdge ATM OC-12 enhanced interface module

rbnEntModuleSE100XC


rbnEntityTypeModule 61


1.3.6.1.4.1.2352.6.9.61

N/A

N/A

The definitive identifier for the SmartEdge 100 cross-connect module

rbnEntPortSMSPIMHSSI


rbnEntityTypePort 9


1.3.6.1.4.1.2352.6.10.9

N/A

N/A

The definitive identifier for the SMS Packet HSSI interface port

rbnEntPowerSupplySMS1000DC


rbnEntityTypePowerSupply 3


1.3.6.1.4.1.2352.6.6.3

N/A

N/A

The definitive identifier for the SMS 1000 DC power supply, model PS-1K-DC

rbnEntBackplaneSMS500Power


rbnEntityTypeBackplane 4


1.3.6.1.4.1.2352.6.4.4

N/A

N/A

The definitive identifier for the SMS 500 power backplane entity

rbnEntBackplaneSE1200Data


rbnEntityTypeBackplane 13


1.3.6.1.4.1.2352.6.4.13

N/A

N/A

The definitive identifier for the SmartEdge 1200 data backplane entity

rbnEntityTypeChassis


rbnEntities 3


1.3.6.1.4.1.2352.6.3

N/A

N/A

The top-level category identifier for entities that reside in the value of the PhysicalClass ENTITY-MIB object as chassis

rbnEntityTypeBackplane


rbnEntities 4


1.3.6.1.4.1.2352.6.4

N/A

N/A

The top-level category identifier for entities that reside in the value of the PhysicalClass ENTITY-MIB object as *backplane*

rbnEntityTypeContainer


rbnEntities 5


1.3.6.1.4.1.2352.6.5

N/A

N/A

The top-level category identifier for entities that reside in the value of the PhysicalClass ENTITY-MIB object as *container*

rbnEntityTypeModule


rbnEntities 9


1.3.6.1.4.1.2352.6.9

N/A

N/A

The top-level category identifier for entities that reside in the value of the PhysicalClass ENTITY-MIB object as *module*

rbnEntBackplaneSE800Data


rbnEntityTypeBackplane 10


1.3.6.1.4.1.2352.6.4.10

N/A

N/A

The definitive identifier for the SmartEdge 800 data backplane entity

rbnEntBackplaneSMS1000Data


rbnEntityTypeBackplane 1


1.3.6.1.4.1.2352.6.4.1

N/A

N/A

The definitive identifier for the SMS 1000 data backplane entity

rbnEntBackplaneSE400Data


rbnEntityTypeBackplane 11


1.3.6.1.4.1.2352.6.4.11

N/A

N/A

The definitive identifier for the SmartEdge 400 data backplane entity

rbnEntBackplaneSE100Data


rbnEntityTypeBackplane 12 1.3.6.1.4.1.2352.6.4.12

N/A

N/A

The definitive identifier for the SmartEdge 100 data backplane entity

rbnEntBackplaneSMS1000Power


rbnEntityTypeBackplane 2


1.3.6.1.4.1.2352.6.4.2

N/A

N/A

The definitive identifier for the SMS 1000 power backplane entity

rbnEntBackplaneSMS500Data rbnEntityTypeBackplane 3


1.3.6.1.4.1.2352.6.4.3

N/A

N/A

The definitive identifier for the SMS 500 data backplane entity

rbnEntBackplaneSMS1800Data


rbnEntityTypeBackplane 5


1.3.6.1.4.1.2352.6.4.5

N/A

N/A

The definitive identifier for the SMS 1800 data backplane entity

rbnEntBackplaneSMS1800Power


rbnEntityTypeBackplane 61.3.6.1.4.1.2352.6.4.6

N/A

N/A

The definitive identifier for the SMS 1800 power backplane entity

rbnEntBackplaneSMS10000Midplane


rbnEntityTypeBackplane 7


1.3.6.1.4.1.2352.6.4.7

N/A

N/A

The definitive identifier for the SMS 10000 midplane entity

rbnEntBackplaneSMS2800Data


rbnEntityTypeBackplane 8


1.3.6.1.4.1.2352.6.4.8

N/A

N/A

The definitive identifier for the SMS 2800 data backplane entity

rbnEntBackplaneSMS2800Power


rbnEntityTypeBackplane 9


1.3.6.1.4.1.2352.6.4.9

N/A

N/A

The definitive identifier for the SMS 2800 power backplane entity

rbnEntChassisSMS1000


rbnEntityTypeChassis 1


1.3.6.1.4.1.2352.6.3.1

N/A

N/A

The definitive identifier for the SMS 1000 chassis entity

rbnEntChassisSMS500


rbnEntityTypeChassis 2


1.3.6.1.4.1.2352.6.3.2

N/A

N/A

The definitive identifier for the SMS 500 chassis entity

rbnEntChassisSMS1800


rbnEntityTypeChassis 3


1.3.6.1.4.1.2352.6.3.3

N/A

N/A

The definitive identifier for the SMS 1800 chassis entity

rbnEntChassisSMS10000


rbnEntityTypeChassis 4


1.3.6.1.4.1.2352.6.3.4

N/A

N/A

The definitive identifier for the SMS 10000 chassis entity

rbnEntChassisSMS2800


rbnEntityTypeChassis 5


1.3.6.1.4.1.2352.6.3.5

N/A

N/A

The definitive identifier for the SMS 2800 chassis entity

rbnEntChassisSE800


rbnEntityTypeChassis 6


1.3.6.1.4.1.2352.6.3.6

N/A

N/A

The definitive identifier for the SmartEdge 800 chassis entity

rbnEntChassisSE400


rbnEntityTypeChassis 7


1.3.6.1.4.1.2352.6.3.7

N/A

N/A

The definitive identifier for the SmartEdge 400 chassis entity

rbnEntChassisSE100


rbnEntityTypeChassis 8


1.3.6.1.4.1.2352.6.3.8

N/A

N/A

The definitive identifier for the SmartEdge 100 chassis entity

rbnEntChassisSE1200


rbnEntityTypeChassis 9


1.3.6.1.4.1.2352.6.3.9

N/A

N/A

The definitive identifier for the SmartEdge 1200 chassis entity

rbnEntContainerSMS10000IO


rbnEntityTypeContainer 10


1.3.6.1.4.1.2352.6.5.10

N/A

N/A

The definitive identifier for the SMS 10000 IO container (slot) entity

rbnEntContainerSMS1000Data


rbnEntityTypeContainer 1


1.3.6.1.4.1.2352.6.5.1

N/A

N/A

The definitive identifier for the SMS 1000 data container (slot) entity

rbnEntContainerSMS2800Power


rbnEntityTypeContainer 11


1.3.6.1.4.1.2352.6.5.11

N/A

N/A

The definitive identifier for the SMS 2800 Power container (slot) entity

rbnEntContainerSMS2800CSM


rbnEntityTypeContainer 12


1.3.6.1.4.1.2352.6.5.12

N/A

N/A

The definitive identifier for the SMS 2800 CSM container (slot) entity

rbnEntContainerSMS2800IO


rbnEntityTypeContainer 13


1.3.6.1.4.1.2352.6.5.13

N/A

N/A

The definitive identifier for the SMS 2800 IO container (slot) entity

rbnEntContainerSE800Data


rbnEntityTypeContainer 14


1.3.6.1.4.1.2352.6.5.14

N/A

N/A

The definitive identifier for the SmartEdge 800 data container (slot) entity

rbnEntContainerSE400Data


rbnEntityTypeContainer 15


1.3.6.1.4.1.2352.6.5.15

N/A

N/A

The definitive identifier for the SmartEdge 400 data container (slot) entity

rbnEntContainerSE100Data


rbnEntityTypeContainer 16


1.3.6.1.4.1.2352.6.5.16

N/A

N/A

The definitive identifier for the SmartEdge 100 data container (slot) entity

rbnEntContainerSE100Carrier


rbnEntityTypeContainer 17


1.3.6.1.4.1.2352.6.5.17

N/A

N/A

The definitive identifier for the SmartEdge 100 carrier container (MIC-card holder) entity

rbnEntContainerSE1200Data


rbnEntityTypeContainer 18


1.3.6.1.4.1.2352.6.5.18

N/A

N/A

The definitive identifier for the SmartEdge 1200 data container (slot) entity

rbnEntContainerSMS1000Power


rbnEntityTypeContainer 2


1.3.6.1.4.1.2352.6.5.2

N/A

N/A

The definitive identifier for the SMS 1000 power container (slot) entity

rbnEntContainerSMS500Data


rbnEntityTypeContainer 3


1.3.6.1.4.1.2352.6.5.3

N/A

N/A

The definitive identifier for the SMS 500 data container (slot) entity

rbnEntContainerSMS500Power


rbnEntityTypeContainer 4


1.3.6.1.4.1.2352.6.5.4

N/A

N/A

The definitive identifier for the SMS 500 power container (slot) entity

rbnEntContainerSMS1800Data


rbnEntityTypeContainer 5


1.3.6.1.4.1.2352.6.5.5

N/A

N/A

The definitive identifier for the SMS 1800 data container (slot) entity

rbnEntContainerSMS1800Power


rbnEntityTypeContainer 6


1.3.6.1.4.1.2352.6.5.6

N/A

N/A

The definitive identifier for the SMS 1800 power container (slot) entity.

rbnEntContainerSMS10000Fabric


rbnEntityTypeContainer 7


1.3.6.1.4.1.2352.6.5.7

N/A

N/A

The definitive identifier for the SMS 10000 fabric container (slot) entity

rbnEntContainerSMS10000Timing


rbnEntityTypeContainer 8


1.3.6.1.4.1.2352.6.5.8

N/A

N/A

The definitive identifier for the SMS 10000 timing container (slot) entity

rbnEntContainerSMS10000SMCM


rbnEntityTypeContainer 9


1.3.6.1.4.1.2352.6.5.9

N/A

N/A

The definitive identifier for the SMS 10000 SM/CM container (slot) entity

rbnEntModuleSMSFE1


rbnEntityTypeModule 10


1.3.6.1.4.1.2352.6.9.10

N/A

N/A

The definitive identifier for the SMS Forwarding Engine 1

rbnEntModuleUnknown


rbnEntityTypeModule 1


1.3.6.1.4.1.2352.6.9.1

N/A

N/A

The identifier used to represent any module that cannot be definitively identified, often because configuration EEPROM is not valid

rbnEntModuleSMSFE2


rbnEntityTypeModule 12


1.3.6.1.4.1.2352.6.9.12

N/A

N/A

The definitive identifier for the SMS forwarding engine 2

rbnEntModuleSMSPIMDS1


rbnEntityTypeModule 14


1.3.6.1.4.1.2352.6.9.14

N/A

N/A

The definitive identifier for the SMS Packet DS-1 interface module

rbnEntModuleSMSPIMCDS3


rbnEntityTypeModule 15


1.3.6.1.4.1.2352.6.9.15

N/A

N/A

The definitive identifier for the SMS Channelized DS-3 interface module

rbnEntModuleSMSCE1


rbnEntityTypeModule 16


1.3.6.1.4.1.2352.6.9.16

N/A

N/A

The definitive identifier for the SMS control engine 1

rbnEntModuleSMSCE2


rbnEntityTypeModule 17


1.3.6.1.4.1.2352.6.9.17

N/A

N/A

The definitive identifier for the SMS control engine 2

rbnEntModuleSMSCE3


rbnEntityTypeModule 18


1.3.6.1.4.1.2352.6.9.18

N/A

N/A

The definitive identifier for the SMS control engine 3

rbnEntModuleSMSAIMT1


rbnEntityTypeModule 20


1.3.6.1.4.1.2352.6.9.20

N/A

N/A

The definitive identifier for the SMS ATM T1 interface module

rbnEntModuleSMSPIME1


rbnEntityTypeModule 22


1.3.6.1.4.1.2352.6.9.22

N/A

N/A

The definitive identifier for the SMS Packet E1 interface module

rbnEntModuleSMSAIME1


rbnEntityTypeModule 23


1.3.6.1.4.1.2352.6.9.23

N/A

N/A

The definitive identifier for the SMS ATM E1 interface module

rbnEntModuleSMSPOSOC3


rbnEntityTypeModule 24


1.3.6.1.4.1.2352.6.9.24

N/A

N/A

The definitive identifier for the SMS POS OC-3 interface module

rbnEntModuleSMSPOSOC12


rbnEntityTypeModule 25


1.3.6.1.4.1.2352.6.9.25

N/A

N/A

The definitive identifier for the SMS POS OC-12 interface module

rbnEntModuleSMSGIGEIM


rbnEntityTypeModule 26


1.3.6.1.4.1.2352.6.9.26

N/A

N/A

The definitive identifier for the SMS Gigabit Ethernet interface module

rbnEntModuleSMSAIMOC12


rbnEntityTypeModule 27


1.3.6.1.4.1.2352.6.9.27

N/A

N/A

The definitive identifier for the SMS ATM OC-12 interface module

rbnEntModuleSMSIPSEC


rbnEntityTypeModule 28


1.3.6.1.4.1.2352.6.9.28

N/A

N/A

The definitive identifier for the SMS IPsec interface module

rbnEntModuleSMSFABRIC


rbnEntityTypeModule 29


1.3.6.1.4.1.2352.6.9.29

N/A

N/A

The definitive identifier for the SMS switch fabric module

rbnEntModuleSMSCM


rbnEntityTypeModule 30


1.3.6.1.4.1.2352.6.9.30

N/A

N/A

The definitive identifier for the SMS connection manager module

rbnEntModuleSMSAIMOC3


rbnEntityTypeModule 3


1.3.6.1.4.1.2352.6.9.3

N/A

N/A

The definitive identifier for the SMS ATM OC-3 interface module

rbnEntModuleSMSTIMING


rbnEntityTypeModule 31


1.3.6.1.4.1.2352.6.9.31

N/A

N/A

The definitive identifier for the SMS timing module

rbnEntModuleSMSSM


rbnEntityTypeModule 32


1.3.6.1.4.1.2352.6.9.32

N/A

N/A

The definitive identifier for the SMS system manager module

rbnEntModuleSMSFE3


rbnEntityTypeModule 35


1.3.6.1.4.1.2352.6.9.35

N/A

N/A

The definitive identifier for the SMS forwarding engine 3

rbnEntModuleSMSCSM


rbnEntityTypeModule 36


1.3.6.1.4.1.2352.6.9.36

N/A

N/A

The definitive identifier for the connection system manager (CSM) module

rbnEntModuleSMSXFE


rbnEntityTypeModule 40


1.3.6.1.4.1.2352.6.9.40

N/A

N/A

The definitive identifier for the SMS extended forwarding engine

rbnEntModuleSMSAIMDS3


rbnEntityTypeModule 4


1.3.6.1.4.1.2352.6.9.4

N/A

N/A

The definitive identifier for the SMS ATM DS-3 interface module

rbnEntModuleSEXC


rbnEntityTypeModule 41


1.3.6.1.4.1.2352.6.9.41

N/A

N/A

The definitive identifier for the SmartEdge cross-connect module

rbnEntModuleSEEIM


rbnEntityTypeModule 42


1.3.6.1.4.1.2352.6.9.42

N/A

N/A

The definitive identifier for the SmartEdge 10/100BaseT Ethernet interface module

rbnEntModuleSEGIGEIM


rbnEntityTypeModule 43


1.3.6.1.4.1.2352.6.9.43

N/A

N/A

The definitive identifier for the SmartEdge Gigabit Ethernet interface module

rbnEntModuleSEPOSOC12


rbnEntityTypeModule 44


1.3.6.1.4.1.2352.6.9.44

N/A

N/A

The definitive identifier for the SmartEdge POS OC-12 interface module

rbnEntModuleSEPOSOC48


rbnEntityTypeModule 45


1.3.6.1.4.1.2352.6.9.45

N/A

N/A

The definitive identifier for the SmartEdge POS OC-48 interface module

rbnEntModuleSEPOSOC3


rbnEntityTypeModule 46


1.3.6.1.4.1.2352.6.9.46

N/A

N/A

The definitive identifier for the SmartEdge POS OC-3 interface module

rbnEntModuleSECHOC12DS1


rbnEntityTypeModule 47


1.3.6.1.4.1.2352.6.9.47

N/A

N/A

The definitive identifier for the SmartEdge Channelized OC-12 DS-1 interface module

rbnEntModuleSECHOC12DS3


rbnEntityTypeModule 48


1.3.6.1.4.1.2352.6.9.48

N/A

N/A

The definitive identifier for the SmartEdge Channelized OC12 DS-3 interface module

rbnEntModuleSEAIMOC3


rbnEntityTypeModule 49


1.3.6.1.4.1.2352.6.9.49

N/A

N/A

The definitive identifier for the SmartEdge ATM OC-3 interface module

rbnEntModuleSEAIMOC12


rbnEntityTypeModule 50


1.3.6.1.4.1.2352.6.9.50

N/A

N/A

The definitive identifier for the SmartEdge ATM OC-12 interface module

rbnEntModuleSMSAIME3


rbnEntityTypeModule 5


1.3.6.1.4.1.2352.6.9.5

N/A

N/A

The definitive identifier for the SMS ATM E3 interface module

rbnEntModuleSECHDS3


rbnEntityTypeModule 51


1.3.6.1.4.1.2352.6.9.51

N/A

N/A

The definitive identifier for the SmartEdge Channelized DS-3 interface module

rbnEntModuleSEDS3


rbnEntityTypeModule 52


1.3.6.1.4.1.2352.6.9.52

N/A

N/A

The definitive identifier for the SmartEdge DS-3 interface module

rbnEntModuleSEAIMDS3


rbnEntityTypeModule 53


1.3.6.1.4.1.2352.6.9.53

N/A

N/A

The definitive identifier for the SmartEdge ATM DS-3 interface module

rbnEntModuleSECHSTM1E1


rbnEntityTypeModule 54


1.3.6.1.4.1.2352.6.9.54

N/A

N/A

The definitive identifier for the SmartEdge Channelized STM-1 to E1 interface module

rbnEntModuleSEE1


rbnEntityTypeModule 55


1.3.6.1.4.1.2352.6.9.55

N/A

N/A

The definitive identifier for the SmartEdge E1 interface module

rbnEntModuleSEXC3


rbnEntityTypeModule 56


1.3.6.1.4.1.2352.6.9.56

N/A

N/A

The definitive identifier for the SmartEdge cross-connect module version 3

rbnEntModuleSEE3


rbnEntityTypeModule 57


1.3.6.1.4.1.2352.6.9.57

N/A

N/A

The definitive identifier for the SmartEdge E3 interface module

rbnEntModuleSEGIGETM


rbnEntityTypeModule 59


1.3.6.1.4.1.2352.6.9.59

N/A

N/A

The definitive identifier for the SmartEdge Gigabit Ethernet with traffic management module

rbnEntModuleSE10GIGEIM


rbnEntityTypeModule 60


1.3.6.1.4.1.2352.6.9.60

N/A

N/A

The definitive identifier for the SmartEdge 10 Gigabit Ethernet interface module

rbnEntModuleSMSEIM


rbnEntityTypeModule 6


1.3.6.1.4.1.2352.6.9.6

N/A

N/A

The definitive identifier for the SMS 10/100BaseT Ethernet interface module

rbnEntModuleSE100EMIC


rbnEntityTypeModule 62


1.3.6.1.4.1.2352.6.9.62

N/A

N/A

The definitive identifier for the SmartEdge 100 10/100BaseT Ethernet media interface connect module

rbnEntModuleSE100FXMIC


rbnEntityTypeModule 63


1.3.6.1.4.1.2352.6.9.63

N/A

N/A

The definitive identifier for the SmartEdge 100 FX-100 Ethernet Media interface connect module

rbnEntModuleSE100GERJMIC


rbnEntityTypeModule 64


1.3.6.1.4.1.2352.6.9.64

N/A

N/A

The definitive identifier for the SmartEdge 100 Gigabit Ethernet Media interface connect module

rbnEntModuleSE100GEFXMIC


rbnEntityTypeModule 65


1.3.6.1.4.1.2352.6.9.65

N/A

N/A

The definitive identifier for the 100 FX-1000 Ethernet Media interface connect module

rbnEntModuleSEXC4


rbnEntityTypeModule 66


1.3.6.1.4.1.2352.6.9.66

N/A

N/A

The definitive identifier for the SmartEdge cross-connect module version 4

rbnEntModuleSE100AIMOC3MIC


rbnEntityTypeModule 67


1.3.6.1.4.1.2352.6.9.67

N/A

N/A

The definitive identifier for the SmartEdge 100 2-port ATM OC-3 media interface connect module

rbnEntModuleSEASE


rbnEntityTypeModule 68


1.3.6.1.4.1.2352.6.9.68

N/A

N/A

The definitive identifier for the SmartEdge Advanced Services Engine module

rbnEntModuleSEFE60GE2


rbnEntityTypeModule 69


1.3.6.1.4.1.2352.6.9.69

N/A

N/A

The definitive identifier for the FE60GE2 Ethernet interface module

rbnEntModuleSEPOSOC192


rbnEntityTypeModule 70


1.3.6.1.4.1.2352.6.9.70

N/A

N/A

The definitive identifier for the SmartEdge POS OC-192 media interface module

rbnEntModuleSMSPIMDS3


rbnEntityTypeModule 7


1.3.6.1.4.1.2352.6.9.7

N/A

N/A

The definitive identifier for the SMS Packet DS-3 interface module

rbnEntModuleSMSPIME3


rbnEntityTypeModule 8


1.3.6.1.4.1.2352.6.9.8

N/A

N/A

The definitive identifier for the SMS Packet E3 interface module

rbnEntModuleSMSPIMHSSI


rbnEntityTypeModule 9


1.3.6.1.4.1.2352.6.9.9

N/A

N/A

The definitive identifier for the SMS Packet HSSI interface module

rbnEntPortUnknown


rbnEntityTypePort 1


1.3.6.1.4.1.2352.6.10.1

N/A

N/A

The identifier used to represent any module that cannot be definitively identified, often because configuration EEPROM is not valid

rbnEntPortSMSPIMDS1


rbnEntityTypePort 14


1.3.6.1.4.1.2352.6.10.14

N/A

N/A

The definitive identifier for the SMS Packet DS-1 interface port

rbnEntPortSMSPIMCDS3


rbnEntityTypePort 15


1.3.6.1.4.1.2352.6.10.15

N/A

N/A

The definitive identifier for the SMS Channelized DS-3 interface port

rbnEntPortSMSCE1MGMT


rbnEntityTypePort 16


1.3.6.1.4.1.2352.6.10.16

N/A

N/A

The definitive identifier for the SMS Control Engine 1, Local management port

rbnEntPortSMSCE2MGMT


rbnEntityTypePort 17


1.3.6.1.4.1.2352.6.10.17

N/A

N/A

The definitive identifier for the SMS Control Engine 2, Local management port

rbnEntPortSMSCE3MGMT


rbnEntityTypePort 18


1.3.6.1.4.1.2352.6.10.18

N/A

N/A

The definitive identifier for the SMS Control Engine 3, Local management port

rbnEntPortSMSAIMT1


rbnEntityTypePort 20


1.3.6.1.4.1.2352.6.10.20

N/A

N/A

The definitive identifier for the SMS ATM T1 interface port

rbnEntPortSMSPIME1


rbnEntityTypePort 22


1.3.6.1.4.1.2352.6.10.22

N/A

N/A

The definitive identifier for the SMS Packet E1 interface port

rbnEntPortSMSAIME1


rbnEntityTypePort 23


1.3.6.1.4.1.2352.6.10.23

N/A

N/A

The definitive identifier for the SMS ATM E1 interface port

rbnEntPortSMSPOSOC3


rbnEntityTypePort 24


1.3.6.1.4.1.2352.6.10.24

N/A

N/A

The definitive identifier for the SMS POS OC-3 interface port

rbnEntPortSMSPOSOC12


rbnEntityTypePort 25


1.3.6.1.4.1.2352.6.10.25

N/A

N/A

The definitive identifier for the SMS POS OC-12 interface port

rbnEntPortSMSGIGEIM


rbnEntityTypePort 26


1.3.6.1.4.1.2352.6.10.26

N/A

N/A

The definitive identifier for the SMS Gigabit Ethernet interface port

rbnEntPortSMSAIMOC12rbnEntityTypePort 27 1.3.6.1.4.1.2352.6.10.27

N/A

N/A

The definitive identifier for the SMS ATM OC-12 interface port

rbnEntPortSMSAIMOC3


rbnEntityTypePort 3


1.3.6.1.4.1.2352.6.10.3

N/A

N/A

The definitive identifier for the SMS ATM OC-3 interface port

rbnEntPortSMSCSMMGMT


rbnEntityTypePort 36


1.3.6.1.4.1.2352.6.10.36

N/A

N/A

The definitive identifier for the Connection System Manager (CSM), Local management port

rbnEntPortSMSAIMDS3


rbnEntityTypePort 4


1.3.6.1.4.1.2352.6.10.4

N/A

N/A

The definitive identifier for the SMS ATM DS-3 interface port

rbnEntPortSEXCMGMT


rbnEntityTypePort 41


1.3.6.1.4.1.2352.6.10.41

N/A

N/A

The definitive identifier for the SmartEdge Cross Connect, Local management port

rbnEntPortSEEIM


rbnEntityTypePort 42


1.3.6.1.4.1.2352.6.10.42

N/A

N/A

The definitive identifier for the SmartEdge 10/100BaseT Ethernet interface port

rbnEntPortSEGIGEIM


rbnEntityTypePort 43


1.3.6.1.4.1.2352.6.10.43

N/A

N/A

The definitive identifier for the SmartEdge Gigabit Ethernet interface port

rbnEntPortSEPOSOC12


rbnEntityTypePort 44


1.3.6.1.4.1.2352.6.10.44

N/A

N/A

The definitive identifier for the SmartEdge POS OC-12 interface port

rbnEntPortSEPOSOC48


rbnEntityTypePort 45


1.3.6.1.4.1.2352.6.10.45

N/A

N/A

The definitive identifier for the SmartEdge POS OC-48 interface port

rbnEntPortSEPOSOC3


rbnEntityTypePort 46


1.3.6.1.4.1.2352.6.10.46

N/A

N/A

The definitive identifier for the SmartEdge POS OC-3 interface port

rbnEntPortSECHOC12DS1


rbnEntityTypePort 47


1.3.6.1.4.1.2352.6.10.47

N/A

N/A

The definitive identifier for the SmartEdge Channelized OC-12 DS-1 interface port

rbnEntPortSECHOC12DS3


rbnEntityTypePort 48


1.3.6.1.4.1.2352.6.10.48

N/A

N/A

The definitive identifier for the SmartEdge Channelized OC-12 DS-3 interface port

rbnEntPortSEAIMOC3


rbnEntityTypePort 49


1.3.6.1.4.1.2352.6.10.49

N/A

N/A

The definitive identifier for the SmartEdge ATM OC-3 interface port

rbnEntPortSEAIMOC12


rbnEntityTypePort 50


1.3.6.1.4.1.2352.6.10.50

N/A

N/A

The definitive identifier for the SmartEdge ATM OC-12 interface port

rbnEntPortSMSAIME3


rbnEntityTypePort 5


1.3.6.1.4.1.2352.6.10.5

N/A

N/A

The definitive identifier for the SMS ATM E3 interface port

rbnEntPortSECHDS3


rbnEntityTypePort 51


1.3.6.1.4.1.2352.6.10.51

N/A

N/A

The definitive identifier for the SmartEdge Channelized DS-3 interface port

rbnEntPortSEDS3


rbnEntityTypePort 52


1.3.6.1.4.1.2352.6.10.52

N/A

N/A

The definitive identifier for the SmartEdge DS-3 interface port

rbnEntPortSEAIMDS3


rbnEntityTypePort 53


1.3.6.1.4.1.2352.6.10.53

N/A

N/A

The definitive identifier for the SmartEdge ATM DS-3 interface port

rbnEntPortSECHSTM1E1


rbnEntityTypePort 54


1.3.6.1.4.1.2352.6.10.54

N/A

N/A

The definitive identifier for the SmartEdge Channelized STM-1 to E1 interface port

rbnEntPortSEE1


rbnEntityTypePort 55


1.3.6.1.4.1.2352.6.10.55

N/A

N/A

The definitive identifier for the SmartEdge E1 interface port

rbnEntPortSEXC3MGMT


rbnEntityTypePort 56


1.3.6.1.4.1.2352.6.10.56

N/A

N/A

The definitive identifier for the SmartEdge Cross Connect 3, Local management port

rbnEntPortSEE3


rbnEntityTypePort 57


1.3.6.1.4.1.2352.6.10.57

N/A

N/A

The definitive identifier for the SmartEdge E3 interface port

rbnEntPortSEAIMOC12E


rbnEntityTypePort 58


1.3.6.1.4.1.2352.6.10.58

N/A

N/A

The definitive identifier for the SmartEdge ATM OC-12 Enhanced interface port

rbnEntPortSEGIGETM


rbnEntityTypePort 59


1.3.6.1.4.1.2352.6.10.59

N/A

N/A

The definitive identifier for the SmartEdge Gigabit Ethernet with Traffic management interface port

rbnEntPortSE10GIGEIM


rbnEntityTypePort 60


1.3.6.1.4.1.2352.6.10.60

N/A

N/A

The definitive identifier for the SmartEdge 10 Gigabit Ethernet interface port

rbnEntPortSMSEIM


rbnEntityTypePort 6


1.3.6.1.4.1.2352.6.10.6

N/A

N/A

The definitive identifier for the SMS 10/100BaseT Ethernet interface port

rbnEntPortSE100XCMGMT


rbnEntityTypePort 61


1.3.6.1.4.1.2352.6.10.61

N/A

N/A

The definitive identifier for the SmartEdge 100 Cross Connect, Local management port

rbnEntPortSE100EIM


rbnEntityTypePort 62


1.3.6.1.4.1.2352.6.10.62

N/A

N/A

The definitive identifier for the SmartEdge 100 10/100BaseT Ethernet interface port

rbnEntPortSE100FXIM


rbnEntityTypePort 63


1.3.6.1.4.1.2352.6.10.63

N/A

N/A

The definitive identifier for the SmartEdge 100 FX-100 Ethernet interface port

rbnEntModuleSE100GERJMIC


rbnEntityTypePort 64


1.3.6.1.4.1.2352.6.10.64

N/A

N/A

The definitive identifier for the SmartEdge 100 Gigabit Ethernet interface port

rbnEntModuleSE100GEFXMIC


rbnEntityTypePort 65


1.3.6.1.4.1.2352.6.10.65

N/A

N/A

The definitive identifier for the SmartEdge 100 FX-1000 Ethernet interface port

rbnEntPortSEXC4MGMT


rbnEntityTypePort 66


1.3.6.1.4.1.2352.6.10.66

N/A

N/A

The definitive identifier for the SmartEdge Cross Connect 4, Local management port

rbnEntPortSE100AIMOC3


rbnEntityTypePort 67


1.3.6.1.4.1.2352.6.10.67

N/A

N/A

The definitive identifier for the SmartEdge 100 ATM OC-3 interface port

rbnEntPortSEPOSOC192


rbnEntityTypePort 68


1.3.6.1.4.1.2352.6.10.68

N/A

N/A

The definitive identifier for the SmartEdge POS OC-192 interface port.

rbnEntPortSMSPIMDS3


rbnEntityTypePort 7


1.3.6.1.4.1.2352.6.10.7

N/A

N/A

The definitive identifier for the SMS Packet DS-3 interface port

rbnEntPortSMSPIME3


rbnEntityTypePort 8


1.3.6.1.4.1.2352.6.10.8

N/A

N/A

The definitive identifier for the SMS Packet E3 interface port

rbnEntPowerSupplySMS1000AC


rbnEntityTypePowerSupply 2


1.3.6.1.4.1.2352.6.6.2

N/A

N/A

The definitive identifier for the SMS 1000 AC Power Supply, model PS-1K-AC

rbnEntPowerSupplySMS500AC


rbnEntityTypePowerSupply 4


1.3.6.1.4.1.2352.6.6.4

N/A

N/A

The definitive identifier for the SMS 500 AC Power Supply

rbnEntPowerSupplySMS500DC


rbnEntityTypePowerSupply 5


1.3.6.1.4.1.2352.6.6.5

N/A

N/A

The definitive identifier for the SMS 500 DC Power Supply

rbnEntPowerSupplySMS1800AC


rbnEntityTypePowerSupply 6


1.3.6.1.4.1.2352.6.6.6

N/A

N/A

The definitive identifier for the SMS 1800 AC Power Supply

rbnEntPowerSupplySMS1800DC


rbnEntityTypePowerSupply 7


1.3.6.1.4.1.2352.6.6.7

N/A

N/A

The definitive identifier for the SMS 1800 DC Power Supply

rbnEntPowerSupplySMS2800AC


rbnEntityTypePowerSupply 8


1.3.6.1.4.1.2352.6.6.8

N/A

N/A

The definitive identifier for the SMS 2800 AC Power Supply

rbnEntPowerSupplySMS2800DC


rbnEntityTypePowerSupply 9


1.3.6.1.4.1.2352.6.6.9

N/A

N/A

The definitive identifier for the SMS 2800 DC Power Supply

rbnEntSensorAlarmSE400


rbnEntityTypeSensor 1


1.3.6.1.4.1.2352.6.8.1

N/A

N/A

The definitive identifier for the SmartEdge 400 alarm card

rbnEntityTypeOther


rbnEntities 1


1.3.6.1.4.1.2352.6.1

N/A

N/A

The top-level category identifier for entities that reside in the value of the PhysicalClass ENTITY-MIB object as other

rbnEntityTypePort


rbnEntities 10


1.3.6.1.4.1.2352.6.10

N/A

N/A

The top-level category identifier for entities that reside in PhysicalClass ENTITY-MIB object as *port*

rbnEntityTypeUnknown


rbnEntities 2


1.3.6.1.4.1.2352.6.2

N/A

N/A

The top-level category identifier for entities that reside in the value of the PhysicalClass ENTITY-MIB object as unknown

rbnEntityTypePowerSupply


rbnEntities 6


1.3.6.1.4.1.2352.6.6

N/A

N/A

The top-level category identifier for entities that reside in the value of the PhysicalClass ENTITY-MIB object as *powerSupply*

rbnEntityTypeSensor


rbnEntities 8


1.3.6.1.4.1.2352.6.8

N/A

N/A

The top-level category identifier for entities which reside in the value of the PhysicalClass ENTITY-MIB object as *sensor*

rbnEntFanSE800


rbnEntityTypeFan 1


1.3.6.1.4.1.2352.6.7.1

N/A

N/A

The definitive identifier for the SmartEdge 800 fan tray

rbnEntFanSE400


rbnEntityTypeFan 2


1.3.6.1.4.1.2352.6.7.2

N/A

N/A

The definitive identifier for the SmartEdge 400 fan tray

rbnEntFanSE1200


rbnEntityTypeFan 3


1.3.6.1.4.1.2352.6.7.3

N/A

N/A

The definitive identifier for the SmartEdge 1200 fan tray

rbnEntPowerSupplyUnknown


rbnEntityTypePowerSupply 1


1.3.6.1.4.1.2352.6.6.1

N/A

N/A

The identifier used to represent any power supply that cannot be definitively identified, often because its configuration EEPROM is not valid

rbnSmartEdge800


rbnProducts 10


1.3.6.1.4.1.2352.1.10

N/A

N/A

The definitive identifier of the SmartEdge 800

rbnSMS1000


rbnProducts 1


1.3.6.1.4.1.2352.1.1

N/A

N/A

The definitive identifier of the SMS 1000

rbnSmartEdge400


rbnProducts 11


1.3.6.1.4.1.2352.1.11

N/A

N/A

The definitive identifier of the SmartEdge 400

rbnSmartEdge100


rbnProducts 12


1.3.6.1.4.1.2352.1.12

N/A

N/A

The definitive identifier of the SmartEdge 100

rbnSmartEdge1200


rbnProducts 13


1.3.6.1.4.1.2352.1.13

N/A

N/A

The definitive identifier of the SmartEdge 1200

rbnSMS500


rbnProducts 2


1.3.6.1.4.1.2352.1.2

N/A

N/A

The definitive identifier of the SMS 500

rbnSMS1800


rbnProducts 3


1.3.6.1.4.1.2352.1.3

N/A

N/A

The definitive identifier of the SMS 1800

rbnSMS10000


rbnProducts 4


1.3.6.1.4.1.2352.1.4

N/A

N/A

The definitive identifier of the SMS 10000

rbnSmartEdgeIDT


rbnProducts 5


1.3.6.1.4.1.2352.1.5

N/A

N/A

The definitive identifier of the SmartEdge IDT

rbnEsp200


rbnProducts 6


1.3.6.1.4.1.2352.1.6

N/A

N/A

The definitive identifier of the ESP 200

rbnEsp5000


rbnProducts 71.3.6.1.4.1.2352.1.7

N/A

N/A

The definitive identifier of the ESP 5000

rbnEsp6000


rbnProducts 8


1.3.6.1.4.1.2352.1.8

N/A

N/A

The definitive identifier of the ESP 6000

rbnSMS2800


rbnProducts 9


1.3.6.1.4.1.2352.1.9

N/A

N/A

The definitive identifier of the SMS 2800

1.28   RBN-PVC-MIB

Defines the objects used to support the creation, deletion, and management of ATM and Ethernet 802.1Q PVCs.

The following sections describes the object information for RBN-PVC-MIB.

1.28.1   rbnAtmPvcConfigTable

This table contains the objects that identify and configure ATM PVCs.

Index: rbnAtmPvcSlot, rbnAtmPvcPort, rbnAtmPvcVpi, rbnAtmPvcVci

Table 53 describes the attributes for rbnAtmPvcConfigTable. All objects in the table are read-only unless otherwise specified.

Table 53    Objects in rbnAtmPvcConfigTable

Object and Object Identifier

Type

Value Range

Description

rbnAtmPvcProfileName


rbnAtmPvcConfigEntry 5


1.3.6.1.4.1.2352.2.7.1.1.1.5

SnmpAdminString

SIZE (1–63)

The profile name to use with the PVC.

rbnAtmPvcEncapsulation


rbnAtmPvcConfigEntry 6


1.3.6.1.4.1.2352.2.7.1.1.1.6

RbnAtmEncapsulation


Integer

0—unknown


1—auto1483


2—bridge1483


3—multi1483


4—route1483


5—l2tp


6—l2tpVcMuxed


7—ppp


8—pppAuto


9—pppOverEthernet


10—pppSerial


11—pppNlpid


12—pppLlc


13—pppVcMuxed


14—raw


15—dot1q1483


16—clips1483


17—pppAutoNopoe


18—cell

The encapsulation to use with the PVC.

rbnAtmPvcRowStatus


rbnAtmPvcConfigEntry 8


1.3.6.1.4.1.2352.2.7.1.1.1.8

RowStatus


Integer

1—active


2—notInService


3—notReady


4—createAndGo


5—createAndWait


6—destroy

The row status for creating, modifying, or deleting an entry in the table.

rbnAtmPvcCircuitType


rbnAtmPvcConfigEntry 9


1.3.6.1.4.1.2352.2.7.1.1.1.9

RbnPvcCircuitType


Integer

1—explicit


2—explicitRange


3— onDemandRange


4—protection

The PVC circuit type. For this MIB object, only those entries with an rbnAtmPvcCircuitType object that has a value 'explicit' can be removed by setting the rbnAtmPvcRowStatus object equal to 'destroy'. A set operation with the rbnAtmPvcRowStatus object equal to 'destroy' on any row with the rbnAtmPvcCircuitType object not equal to 'explicit' results in an INCONSISTENT_VALUE_ERROR.

rbnAtmPvcCircuitHandle


rbnAtmPvcConfigEntry 10


1.3.6.1.4.1.2352.2.7.1.1.1.1

RbnCircuitHandle


Octet String

SIZE (8)

Used internally to uniquely identify a circuit. The value of this object can be used to correlate entries with those in rbnBindTable defined in the RBN-BIND-MIB.

rbnAtmPvcClearCircuit


rbnAtmPvcConfigEntry 11


1.3.6.1.4.1.2352.2.7.1.1.1.11

TruthValue

1—true


2—false

When this object is true, the system clears active subscriber sessions on the specified circuit. When false, there is no action taken. This object can only be written when the conceptual row exists. When this object is set to true and the encapsulation of the circuit is bridged or routed (for example, bridge1483 or route1483), subscribers reauthenticate after being cleared. This object is read-create.

1.28.2   rbnFrameRelayPvcConfigTable

This table contains the objects that identify and configure Frame Relay PVCs.

Index: rbnFrameRelayPvcSlot, rbnFrameRelayPvcPort, rbnFrameRelayPvcChannel, rbnFrameRelayPvcDLCI

Table 54 describes the attributes for rbnFrameRelayPvcConfigTable. All objects in the table are read-only unless otherwise specified.

Table 54    Objects in rbnFrameRelayPvcConfigTable

Object and Object Identifier

Type

Value Range

Description

rbnFrameRelayPvcProfileName


rbnFrameRelayPvcConfigEntry 5

SnmpAdminString

SIZE (1–63)

The profile name to use with the PVC. This object is read-create.

rbnFrameRelayPvcEncapsulation


rbnFrameRelayPvcConfigEntry 6

RbnFrameRelayEncapsulation

N/A

The encapsulation to use with the PVC. This object is read-create.

rbnFrameRelayPvcRowStatus


rbnFrameRelayPvcConfigEntry 8

RowStatus


Integer

1—active


2—notInService


3—notReady


4— createAndGo


5— createAndWait


6—destroy

The row status for creating, modifying, or deleting an entry in the table. This object is read-create.

rbnFrameRelayPvcCircuitType


rbnFrameRelayPvcConfigEntry 9

RbnPvcCircuitType


Integer

1—explicit


2—


explicitRange


3—


onDemandRange


4—protection

The PVC circuit type. For this MIB object, only those entries with an rbnFrameRelayPvcCircuitType object that has a value of explicit can be removed by setting the rbnFrameRelayPvcRowStatus object equal to destroy. A set operation with the rbnFrameRelayPvcRowStatuss object equal to destroy on any row with the rbnFrameRelayPvcCircuitType not equal to explicit results in an INCONSISTENT_VALUE_ERROR. This object is read-create.

rbnFrameRelayPvcCircuitHandle


rbnFrameRelayPvcConfigEntry 10

RbnCircuitHandle


Octet String

SIZE (8)

Used internally to uniquely identify a circuit. The value of this object can be used to correlate entries with those in rbnBindTable defined in the RBN-BIND-MIB.

rbnFrameRelayPvcClearCircuit


rbnFrameRelayPvcConfigEntry 11

TruthValue

1—true


2—false

When this object is true, the system clears active subscriber sessions on the specified circuit. When false, there is no action taken. This object can only be written when the conceptual row exists.


When this object is set to true and the encapsulation of the circuit is bridged or routed (for example, bridge1490 or route1490), subscribers re-authenticate after being cleared. This object is read-create.

1.28.3   rbnDot1qPvcOnEthConfigTable

This table contains the objects that identify and configure IEEE 802.1Q PVCs on Ethernet ports.

Index: rbnDot1qPvcOnEthSlot, rbnDot1qPvcOnEthPort, rbnDot1qPvcOnEthVlanId

Table 55 describes the attributes for rbnDot1qPvcOnEthConfigTable. All objects in the table are read-only unless otherwise specified.

Table 55    Objects in rbnDot1qPvcOnEthConfigTable

Object and Object Identifier

Type

Value Range

Description

rbnDot1qPvcOnEthRowStatus


rbnDot1qPvcOnEthConfigEntry 4


1.3.6.1.4.1.2352.2.7.1.3.1.4

RowStatus


Integer

1—active


2—notInService


3—notReady


4—createAndGo


5—createAndWait


6—destroy

The row status for creating, modifying, or deleting an entry in the table.

rbnDot1qPvcOnEthProfileName


rbnDot1qPvcOnEthConfigEntry 5


1.3.6.1.4.1.2352.2.7.1.3.1.5

SnmpAdminString

SIZE (1–63)

The profile name to use with the PVC.

rbnDot1qPvcOnEthEncapsulation


rbnDot1qPvcOnEthConfigEntry 6


1.3.6.1.4.1.2352.2.7.1.3.1.6

RbnDot1qEncap- sulation


Integer

0—unknown


1—ipOverEthernet


2—dot1qMulti


3—pppOverEthernet


4—dot1qRaw


5—dot1qClips


6—dot1qTunnelMulti


7—dot1qTunnelPppOverEthernet


8—dot1qTunnelRaw


9—dot1qTunnelClips

The encapsulation to use with the PVC.

rbnDot1qPvcOnEthCircuitType


rbnDot1qPvcOnEthConfigEntry 7


1.3.6.1.4.1.2352.2.7.1.3.1.7

RbnPvcCircuit Type


Integer

1—explicit


2—explicitRange


3—onDemandRange


4—protection

The PVC circuit type. For this MIB object, only those entries with an rbnDot1qPvcOnEthCircuitType object that has a value of explicit can be removed by setting the rbnDot1qPvcOnEthRowStatus object equal to destroy. A set operation with the rbnDot1qPvcOnEthRowStatus object equal to destroy on any row with the rbnDot1qPvcOnEthCircuitType not equal to explicit results in an INCONSISTENT_VALUE_ERROR.

rbnDot1qPvcOnEthCircuitHandle


rbnDot1qPvcOnEthConfigEntry 8


1.3.6.1.4.1.2352.2.7.1.3.1.8

RbnCircuitHandle


Octet String

SIZE (8)

Used internally to uniquely identify a circuit. The value of this object can be used to correlate entries with those in the rbnBindTable object defined in the RBN-BIND-MIB.

rbnDot1qPvcOnEthClearCircuit


rbnDot1qPvcOnEthConfigEntry 9


1.3.6.1.4.1.2352.2.7.1.3.1.9

TruthValue

1—true


2—false

When this object is true (1), the system clears active subscriber sessions on the specified circuit. When false (2), there is no action taken. This object can be written only when the conceptual row exists. This object is read-create.

1.28.4   rbnDot1qPvcOnAtmConfigTable

This table contains the objects that identify and configure IEEE 802.1Q PVCs on ATM circuits.

Index: rbnDot1qPvcOnAtmSlot, rbnDot1qPvcOnAtmPort, rbnDot1qPvcOnAtmVpi, rbnDot1qPvcOnAtmVci, rbnDot1qPvcOnAtmVlanId

Table 56 describes the attributes for rbnDot1qPvcOnAtmConfigTable. All objects in the table are read-only unless otherwise specified.

Table 56    Objects in rbnDot1qPvcOnAtmConfigTable

Object and Object Identifier

Type

Value Range

Description

rbnDot1qPvcOnAtmRowStatus


rbnDot1qPvcOnAtmConfigEntry 6

RowStatus


Integer

1—active


2—notInService


3—notReady


4—createAndGo


5—createAndWait


6—destroy

The row status for creating, modifying, or deleting an entry in the table.

rbnDot1qPvcOnAtmProfileName


rbnDot1qPvcOnAtmConfigEntry 7

SnmpAdminString

SIZE (1–63)

The profile name to use with the PVC.

rbnDot1qPvcOnAtmEncapsulation


rbnDot1qPvcOnAtmConfigEntry 8

RbnDot1qEncapsulation


Integer

0—unknown


1—ipOverEthernet


2—dot1qMulti


3—pppOverEthernet


4—dot1qRaw


5—dot1qClips


6—dot1qTunnelMulti


7—dot1qTunnelPppOverEthernet


8—dot1qTunnelRaw


9—dot1qTunnelClips

The encapsulation to use with the PVC.

rbnDot1qPvcOnAtmCircuitType


rbnDot1qPvcOnAtmConfigEntry 9

RbnPvcCircuitType


Integer

1—explicit


2—explicitRange


3—onDemandRange


4—protection

The PVC circuit type. For this object, only entries of the rbnDot1qPvcOnAtmCircuit Type object with the value 'explicit' may be removed by setting the rbnDot1qPvcOnAtmRow Status object equal to 'destroy'. A set operation with the rbnDot1qPvcOnAtmRow Status object equal to 'destroy' on any row with the rbnDot1qPvcOnAtmCircuit Type object not equal to 'explicit' results in an INCONSISTENT_VALUE_ERROR.

rbnDot1qPvcOnAtmCircuitHandle


rbnDot1qPvcOnAtmConfigEntry 10

RbnCircuitHandle


Octet String

SIZE (8)

Used internally to uniquely identify a circuit. The value of this object can be used to correlate entries with those in the rbnBindTable object defined in the RBN-BIND-MIB.

rbnDot1qPvcOnAtmClearCircuit


rbnDot1qPvcOnAtmConfigEntry 11

TruthValue

1—true


2—false

When this object is true (1), the system clears active subscriber sessions on the specified circuit. When false (2), there is no action taken. This object can be written only when the conceptual row exists. This object is read-create.

1.28.5   rbnDot1qPvcOnFrConfigTable

This table contains the objects that identify and configure IEEE 802.1Q PVCs on Frame Relay ports.

Index: rbnDot1qPvcOnFrSlot, rbnDot1qPvcOnFrPort, rbnDot1qPvcOnFrChannel, rbnDot1qPvcOnFrDLCI, rbnDot1qPvcOnFrVlanId

Table 57 describes the attributes for rbnDot1qPvcOnFrConfigTable. All objects in the table are read-only unless otherwise specified.

Table 57    Objects in rbnDot1qPvcOnFrConfigTable

Object and Object Identifier

Type

Value Range

Description

rbnDot1qPvcOnFrRowStatus


rbnDot1qPvcOnFrConfigEntry 6

RowStatus


Integer

1—active


2—notInService


3—notReady


4—createAndGo


5—createAndWait


6—destroy

The row status for creating, modifying, or deleting an entry in the table.

rbnDot1qPvcOnFrProfileName


rbnDot1qPvcOnFrConfigEntry 7

SnmpAdminString

SIZE (1–63)

The profile name to use with the PVC.

rbnDot1qPvcOnFrEncapsulation


rbnDot1qPvcOnFrConfigEntry 8

RbnDot1qEncapsulation


Integer

0—unknown


1—ipOverEthernet


2—dot1qMulti


3—pppOverEthernet


4—dot1qRaw


5—dot1qClips


6—dot1qTunnelMulti


7—dot1qTunnelPppOverEthernet


8—dot1qTunnelRaw


9—dot1qTunnelClips

The encapsulation to use with the PVC.

rbnDot1qPvcOnFrCircuitType


rbnDot1qPvcOnFrConfigEntry 9

RbnPvcCircuitType


Integer

1—explicit


2—explicitRange


3—onDemandRange


4—protection

The PVC circuit type. For this object, only entries of the rbnDot1qPvcOnFrCircuitType object with the value 'explicit' may be removed by setting the rbnDot1qPvcOnFrRowStatus object equal to 'destroy'. A set operation with the rbnDot1qPvcOnFrRowStatus object equal to 'destroy' on any row with the rbnDot1qPvcOnFrCircuit Type object not equal to 'explicit' results in an INCONSISTENT_VALUE_ERROR.

rbnDot1qPvcOnFrCircuitHandle


rbnDot1qPvcOnFrConfigEntry 10

RbnCircuitHandle


Octet String

SIZE (8)

Used internally to uniquely identify a circuit. The value of this object can be used to correlate entries with those in the rbnBindTable object defined in the RBN-BIND-MIB.

rbnDot1qPvcOnFrClearCircuit


rbnDot1qPvcOnFrConfigEntry 11

TruthValue

1—true


2—false

When true (1), the system clears active subscriber sessions on the specified circuit. When false (2), there is no action taken. This object can be written only when the conceptual row exists. This object is read-create.

1.29   RBN-QOS-MIB

This table contains the objects that manage interfaces that have quality of service (QoS) enabled. These objects also monitor the QoS queue statistics on the subscriber circuits (CLIPS and PPPoE), with traffic management (TM)-based priority weighted fair queuing (PWFQ).

The following sections describes object information for RBN-QOS-MIB.

1.29.1   rbnQosInterfaceTable

This table contains entries for every packet-oriented IF-MIB layer for which QoS is enabled.

Index: ifIndex

Table 58 describes the attributes in rbnQosInterfaceTable. All objects in the table are read-only.

Table 58    Objects in rbnQosInterfaceTable

Object and Object Identifier

Type

Value Range

Description

rbnQosIfInOctets


rbnQosInterfaceEntry 1


1.3.6.1.4.1.2352.2.22.1.1.1.1

Counter32

N/A

The total number of post-limited octets received on the interface, including framing characters. Discontinuities in the value of this counter can occur at reinitialization of the management system and at other times as indicated by the value of the ifCounterDiscontinuityTime object.

rbnQosIfHCInOctets


rbnQosInterfaceEntry 2


1.3.6.1.4.1.2352.2.22.1.1.1.2

Counter64

N/A

The total number of post-limited octets received on the interface, including framing characters. This object is 64-bit version of the rbnQosIfInOctets object. Discontinuities in the value of this counter can occur at reinitialization of the management system and at other times as indicated by the value of the ifCounterDiscontinuityTime object.

rbnQosIfOutOctets


rbnQosInterfaceEntry 3


1.3.6.1.4.1.2352.2.22.1.1.1.3

Counter32

N/A

The total number of prelimited octets transmitted out of the interface, including framing characters. Discontinuities in the value of this counter can occur at reinitialization of the management system and at other times as indicated by the value of the ifCounterDiscontinuityTime object.

rbnQosIfHCOutOctets


rbnQosInterfaceEntry 4


1.3.6.1.4.1.2352.2.22.1.1.1.4

Counter64

N/A

The total number of prelimited octets transmitted out of the interface, including framing characters. This object is a 64-bit version of the rbnQosIfOutOctets object. Discontinuities in the value of this counter can occur at reinitialization of the management system and at other times as indicated by the value of the ifCounterDiscontinuityTime object.

rbnQosIfInDroppedOctets


rbnQosInterfaceEntry 5


1.3.6.1.4.1.2352.2.22.1.1.1.5

Counter32

N/A

The total number of received octets that were dropped on the interface, including but not limited to octets dropped due to limiting. Discontinuities in the value of this counter can occur at reinitialization of the management system and at other times as indicated by the value of the ifCounterDiscontinuityTime object.

rbnQosIfHCInDroppedOctets


rbnQosInterfaceEntry 6


1.3.6.1.4.1.2352.2.22.1.1.1.6

Counter64

N/A

The total number of received octets that were dropped on the interface, including but not limited to octets dropped due to limiting. This object is a 64-bit version of the rbnQosIfInDroppedOctets object. Discontinuities in the value of this counter can occur at reinitialization of the management system and at other times as indicated by the value of the ifCounterDiscontinuityTime object.

rbnQosIfOutDroppedOctets


rbnQosInterfaceEntry 7


1.3.6.1.4.1.2352.2.22.1.1.1.7

Counter32

N/A

The total number of outbound octets that were dropped on the interface, including but not limited to octets dropped due to limiting. Discontinuities in the value of this counter can occur at reinitialization of the management system and at other times as indicated by the value of the ifCounterDiscontinuityTime object.

rbnQosIfHCOutDroppedOctets


rbnQosInterfaceEntry 8


1.3.6.1.4.1.2352.2.22.1.1.1.8

Counter64

N/A

The total number of outbound octets that were dropped on the interface, including but not limited to octets dropped due to limiting. This object is a 64-bit version of the rbnQosIfOutDroppedOctets object. Discontinuities in the value of this counter can occur at reinitialization of the management system and at other times as indicated by the value of the ifCounterDiscontinuityTime object.

1.29.2   rbnQosInterfaceQueueStatsTable

This table specifies statistical information for each transmit queue. It contains the transmit queue octet counts for each packet-oriented IF-MIB layer for which QoS is enabled.

Index: ifIndex, rbnQosIfQueueId

Table 59 describes the attributes in rbnQosInterfaceQueueStatsTable. All objects in the table are read-only.

Table 59    Objects in rbnQosInterfaceQueueStatsTable

Object and Object Identifier

Type

Value Range

Description

rbnQosIfQueueOutOctets


rbnQosInterfaceQueueStatsEntry 2


1.3.6.1.4.1.2352.2.22.1.2.1.2

Counter32

N/A

The number of octets transmitted out of this queue. Discontinuities in the value of this counter can occur at reinitialization of the management system and at other times as indicated by the value of the ifCounterDiscontinuityTime object.

rbnQosIfQueueOutPkts


rbnQosInterfaceQueueStatsEntry 3


1.3.6.1.4.1.2352.2.22.1.2.1.3

Counter32

N/A

The number of packets transmitted out of this queue. Discontinuities in the value of this counter can occur at reinitialization of the management system and at other times as indicated by the value of the ifCounterDiscontinuityTime object.

rbnQosIfQueueWredDroppedOctets


rbnQosInterfaceQueueStatsEntry 4


1.3.6.1.4.1.2352.2.22.1.2.1.4

Counter32

N/A

The number of octets dropped due to the application of a WRED algorithm. Discontinuities in the value of this counter can occur at reinitialization of the management system and at other times as indicated by the value of the ifCounterDiscontinuityTime object.

rbnQosIfQueueWredDroppedPkts


rbnQosInterfaceQueueStatsEntry 5


1.3.6.1.4.1.2352.2.22.1.2.1.5

Counter32

N/A

The number of packets dropped due to the application of a WRED algorithm. Discontinuities in the value of this counter can occur at reinitialization of the management system and at other times as indicated by the value of the ifCounterDiscontinuityTime object.

rbnQosIfQueueTailDroppedOctets


rbnQosInterfaceQueueStatsEntry 6


1.3.6.1.4.1.2352.2.22.1.2.1.6

Counter32

N/A

The number of octets dropped when the total number of packets in this queue was greater than the maximum threshold. Discontinuities in the value of this counter can occur at reinitialization of the management system and at other times as indicated by the value of the ifCounterDiscontinuityTime object.

rbnQosIfQueueTailDroppedPkts


rbnQosInterfaceQueueStatsEntry 7


1.3.6.1.4.1.2352.2.22.1.2.1.7

Counter32

N/A

The number of packets dropped when the total number of packets in this queue was greater than the maximum threshold. Discontinuities in the value of this counter can occur at reinitialization of the management system and at other times as indicated by the value of the ifCounterDiscontinuityTime object.

rbnQosIfQueueHCOutOctets


rbnQosInterfaceQueueStatsEntry 8


1.3.6.1.4.1.2352.2.22.1.2.1.8

Counter64

N/A

The number of octets transmitted out of this queue. This object is a 64-bit version of the rbnQosIfQueueOutOctets object. Discontinuities in the value of this counter can occur at reinitialization of the management system and at other times as indicated by the value of the ifCounterDiscontinuityTime object.

rbnQosIfQueueHCOutPkts


rbnQosInterfaceQueueStatsEntry 9


1.3.6.1.4.1.2352.2.22.1.2.1.9

Counter64

N/A

The number of packets transmitted out of this queue. This object is a 64-bit version of the rbnQosIfQueueOutPkts object. Discontinuities in the value of this counter can occur at reinitialization of the management system and at other times as indicated by the value of the ifCounterDiscontinuityTime object.

rbnQosIfQueueHCWredDroppedOctets


rbnQosInterfaceQueueStatsEntry 10


1.3.6.1.4.1.2352.2.22.1.2.1.10

Counter64

N/A

The number of octets dropped due to the application of a WRED algorithm. This object is a 64-bit version of the rbnQosIfQueueWredDroppedOctets object. Discontinuities in the value of this counter can occur at reinitialization of the management system and at other times as indicated by the value of the ifCounterDiscontinuityTime object.

rbnQosIfQueueHCWredDroppedPkts


rbnQosInterfaceQueueStatsEntry 11


1.3.6.1.4.1.2352.2.22.1.2.1.11

Counter64

N/A

The number of packets dropped due to the application of a WRED algorithm. This object is a 64-bit version of the rbnQosIfQueueWredDroppedPkts object. Discontinuities in the value of this counter can occur at reinitialization of the management system and at other times as indicated by the value of the ifCounterDiscontinuityTime object.

rbnQosIfQueueHCTailDroppedOctets


rbnQosInterfaceQueueStatsEntry 12


1.3.6.1.4.1.2352.2.22.1.2.1.12

Counter64

N/A

The number of octets dropped when the total number of packets in this queue was greater than the maximum threshold. This object is a 64-bit version of the rbnQosIfQueueTailDroppedOctets object. Discontinuities in the value of this counter can occur at reinitialization of the management system and at other times as indicated by the value of the ifCounterDiscontinuityTime object.

rbnQosIfQueueHCTailDroppedPkts


rbnQosInterfaceQueueStatsEntry 13


1.3.6.1.4.1.2352.2.22.1.2.1.13

Counter64

N/A

The number of packets dropped when the total number of packets in this queue was greater than the maximum threshold. This object is a 64-bit version of the rbnQosIfQueueTailDroppedPkts object. Discontinuities in the value of this counter can occur at reinitialization of the management system and at other times as indicated by the value of the ifCounterDiscontinuityTime object.

1.29.3   rbnQosSubscriberQueueStatsTable

This table specifies per-transmit queue statistical information. It contains the transmit queue octet counts for each active subscriber session for which QoS queuing policy is enabled.

Index: rbnSubsActiveName, rbnSubsActiveSessionId, rbnQosSubsQueueId

Table 60 describes the attributes in rbnQosSubscriberQueueStatsTable. All objects in the table are read-only.

Table 60    Objects in rbnQosSubscriberQueueStatsTable

Object and Object Identifier

Type

Value Range

Description

rbnQosSubsQueuePolicyName


rbnQosSubscriberQueueStatsEntry 2


1.3.6.1.4.1.2352.2.22.1.3.1.2

SnmpAdminString

SIZE (1–39)

The name of the queuing policy the subscriber circuit is using.

rbnQosSubsQueueOutOctets


rbnQosSubscriberQueueStatsEntry 3


1.3.6.1.4.1.2352.2.22.1.3.1.3

Counter32

N/A

The number of octets transmitted out of this queue. Discontinuities in the value of this counter can occur at reinitialization of the management system.

rbnQosSubsQueueOutPkts


rbnQosSubscriberQueueStatsEntry 4


1.3.6.1.4.1.2352.2.22.1.3.1.4

Counter32

N/A

The number of packets transmitted out of this queue. Discontinuities in the value of this counter can occur at reinitialization of the management system.

rbnQosSubsQueueWredDroppedOctets


rbnQosSubscriberQueueStatsEntry 5


1.3.6.1.4.1.2352.2.22.1.3.1.5

Counter32

N/A

The number of octets dropped due to the application of a WRED algorithm. Discontinuities in the value of this counter can occur at reinitialization of the management system.

rbnQosSubsQueueWredDroppedPkts


rbnQosSubscriberQueueStatsEntry 6


1.3.6.1.4.1.2352.2.22.1.3.1.6

Counter32

N/A

The number of packets dropped due to the application of a WRED algorithm. Discontinuities in the value of this counter can occur at reinitialization of the management system.

rbnQosSubsQueueTailDroppedOctets


rbnQosSubscriberQueueStatsEntry 7


1.3.6.1.4.1.2352.2.22.1.3.1.

Counter32

N/A

The number of octets dropped when the total number of packets in this queue was greater than the maximum threshold. Discontinuities in the value of this counter can occur at reinitialization of the management system.

rbnQosSubsQueueTailDroppedPkts


rbnQosSubscriberQueueStatsEntry 8


1.3.6.1.4.1.2352.2.22.1.3.1.8

Counter32

N/A

The number of packets dropped when the total number of packets in this queue was greater than the maximum threshold. Discontinuities in the value of this counter can occur at reinitialization of the management system.

rbnQosSubsQueueHCOutOctets


rbnQosSubscriberQueueStatsEntry 9


1.3.6.1.4.1.2352.2.22.1.3.1.9

Counter64

N/A

The number of octets transmitted out of this queue. This object is a 64-bit version of the rbnQosSubsQueueOutOctets object. Discontinuities in the value of this counter can occur at reinitialization of the management system.

rbnQosSubsQueueHCOutPkts


rbnQosSubscriberQueueStatsEntry 10


1.3.6.1.4.1.2352.2.22.1.3.1.10

Counter64

N/A

The number of packets transmitted out of this queue. This object is a 64-bit version of the rbnQosSubsQueueOutPkts object. Discontinuities in the value of this counter can occur at reinitialization of the management system.

rbnQosSubsQueueHCWredDroppedOctets


rbnQosSubscriberQueueStatsEntry 11


1.3.6.1.4.1.2352.2.22.1.3.1.11

Counter64

N/A

The number of octets dropped due to the application of a WRED algorithm. This object is a 64-bit version of the rbnQosSubsQueueWredDroppedOctets object. Discontinuities in the value of this counter can occur at reinitialization of the management system.

rbnQosSubsQueueHCWredDroppedPkts


rbnQosSubscriberQueueStatsEntry 12


1.3.6.1.4.1.2352.2.22.1.3.1.12

Counter64

N/A

The number of packets dropped due to the application of a WRED algorithm. This object is a 64-bit version of the rbnQosSubsQueueWredDroppedPkts object. Discontinuities in the value of this counter can occur at reinitialization of the management system.

rbnQosSubsQueueHCTailDroppedOctets


rbnQosSubscriberQueueStatsEntry 13


1.3.6.1.4.1.2352.2.22.1.3.1.13

Counter64

N/A

The number of octets dropped when the total number of packets in this queue was greater than the maximum threshold. This object is a 64-bit version of the rbnQosSubsQueueTailDroppedOctets object. Discontinuities in the value of this counter can occur at reinitialization of the management system.

rbnQosSubsQueueHCTailDroppedPkts


rbnQosSubscriberQueueStatsEntry 14


1.3.6.1.4.1.2352.2.22.1.3.1.14

Counter64

N/A

The number of packets dropped when the total number of packets in this queue was greater than the maximum threshold. This object is a 64-bit version of the rbnQosSubsQueueTailDroppedPkts object. Discontinuities in the value of this counter can occur at reinitialization of the management system.

1.29.4   rbnQosIntfRLClassStatsTable

This table specifies per-class statistical information. It contains the class octet counts for each packet-oriented IF-MIB layer to which the class-based policing and metering policy is applied.

Index: ifIndex, rbnQosIfRLPolicyType, rbnQosIfRLClassId

Table 61 describes the attributes in rbnQosIntfRLClassStatsTable. All objects in the table are read-only.

Table 61    Objects in rbnQosIntfRLClassStatsTable

Object and Object Identifier

Type

Value Range

Description

rbnQosIfRLPolicyName


rbnQosIntfRLClassStatsEntry 3


1.3.6.1.4.1.2352.2.22.1.4.1.3

SnmpAdminString

SIZE (1–39)

Name of the rate-limit policy.

rbnQosIfRLClassName


rbnQosIntfRLClassStatsEntry 4


1.3.6.1.4.1.2352.2.22.1.4.1.4

SnmpAdminString

SIZE (1–39)

Name of the class in the rate-limit policy access list.

rbnQosIfRLClassConformOctets


rbnQosIntfRLClassStatsEntry 5


1.3.6.1.4.1.2352.2.22.1.4.1.5

Counter64

N/A

The number of octets that conform to the rate limit set on the interface for which class counters are enabled.

rbnQosIfRLClassConformPkts


rbnQosIntfRLClassStatsEntry 6


1.3.6.1.4.1.2352.2.22.1.4.1.6

Counter64

N/A

The number of packets that conform to the rate limit set on the interface for which class counters are enabled.

rbnQosIfRLClassConformDroppedOctets


rbnQosIntfRLClassStatsEntry 7


1.3.6.1.4.1.2352.2.22.1.4.1.7

Counter64

N/A

The number of octets dropped due to the application of a conform action on packets that conform to the rate limit set on the interface for which class counters are enabled.

rbnQosIfRLClassConformDroppedPkts


rbnQosIntfRLClassStatsEntry 8


1.3.6.1.4.1.2352.2.22.1.4.1.8

Counter64

N/A

The number of packets dropped due to the application of a conform action on packets that conform to the rate limit set on the interface for which class counters are enabled.

rbnQosIfRLClassExceedOctets


rbnQosIntfRLClassStatsEntry 9


1.3.6.1.4.1.2352.2.22.1.4.1.9

Counter64

N/A

The number of octets that exceed the rate limit set on the interface for which class counters are enabled.

rbnQosIfRLClassExceedPkts


rbnQosIntfRLClassStatsEntry 10


1.3.6.1.4.1.2352.2.22.1.4.1.10

Counter64

N/A

The number of packets that exceed the rate limit set on the interface.

rbnQosIfRLClassExceedDroppedOctets


rbnQosIntfRLClassStatsEntry 11


1.3.6.1.4.1.2352.2.22.1.4.1.11

Counter64

N/A

The number of octets dropped due to the application of an exceed action on packets that exceed the rate limit set on the interface for which class counters are enabled.

rbnQosIfRLClassExceedDroppedPkts


rbnQosIntfRLClassStatsEntry 12


1.3.6.1.4.1.2352.2.22.1.4.1.12

Counter64

N/A

The number of packets dropped due to the application of an exceed action on packets that exceed the rate limit set on the interface for which class counters are enabled.

rbnQosIfRLClassViolateOctets


rbnQosIntfRLClassStatsEntry 13


1.3.6.1.4.1.2352.2.22.1.4.1.13

Counter64

N/A

The number of octets that violate the normal and maximum burst sizes on the interface for which class counters are enabled.

rbnQosIfRLClassViolatePkts


rbnQosIntfRLClassStatsEntry 14


1.3.6.1.4.1.2352.2.22.1.4.1.14

Counter64

N/A

The number of packets that violate the normal and maximum burst sizes on the interface for which class counters are enabled.

rbnQosIfRLClassViolateDroppedOctets


rbnQosIntfRLClassStatsEntry 15


1.3.6.1.4.1.2352.2.22.1.4.1.15

Counter64

N/A

The number of octets dropped due to the application of a violate action on packets that violate the normal and maximum burst sizes on the interface for which class counters are enabled.

rbnQosIfRLClassViolateDroppedPkts


rbnQosIntfRLClassStatsEntry 16


1.3.6.1.4.1.2352.2.22.1.4.1.16

Counter64

N/A

The number of packets dropped due to the application of a violate action on packets that violate the normal and maximum burst sizes on the interface for which class counters are enabled.

1.29.5   rbnQosSubscriberRLClassStatsTable

This table specifies per-class statistical information on the subscriber circuits. It contains the class octet counts for each active subscriber session to which the class-based policing and metering policy is applied when the counters are enabled for the class.

All MIB objects defined in the table are viewed within the context identified in the SNMP protocol (i.e. the community string in SNMPv1 or SNMPv2 or the contextName in SNMPv3)

Index: rbnSubsActiveName, rbnSubsActiveSessionId, rbnQosSubsRLPolicyType, rbnQosSubsRLClassId

Table 62 describes the attributes in rbnQosSubscriberRLClassStatsTable. All objects in the table are read-only.

Table 62    Objects in rbnQosSubscriberRLClassStatsTable

Object and Object Identifier

Type

Value Range

Description

rbnQosSubsRLPolicyName


rbnQosSubscriberRLClassStatsEntry 3


1.3.6.1.4.1.2352.2.22.1.5.1.3

SnmpAdminString

SIZE (1–39)

Name of the rate-limit policy.

rbnQosSubsRLClassName


rbnQosSubscriberRLClassStatsEntry 4


1.3.6.1.4.1.2352.2.22.1.5.1.4

SnmpAdminString

SIZE (1–39)

Name of the class in the rate-limit policy access list.

rbnQosSubsRLClassConformOctets


rbnQosSubscriberRLClassStatsEntry 5


1.3.6.1.4.1.2352.2.22.1.5.1.5

Counter64

N/A

The number of octets that conform to the rate limit set on the subscriber circuit.

rbnQosSubsRLClassConformPkts


rbnQosSubscriberRLClassStatsEntry 6


1.3.6.1.4.1.2352.2.22.1.5.1.6

Counter64

N/A

The number of packets that conform to the rate limit set on the subscriber circuit.

rbnQosSubsRLClassConformDroppedOctets


rbnQosSubscriberRLClassStatsEntry 7


1.3.6.1.4.1.2352.2.22.1.5.1.7

Counter64

N/A

The number of octets dropped due to the application of a conform action on packets that conform to the rate limit set on the subscriber circuit.

rbnQosSubsRLClassConformDroppedPkts


rbnQosSubscriberRLClassStatsEntry 8


1.3.6.1.4.1.2352.2.22.1.5.1.8

Counter64

N/A

The number of packets dropped due to the application of a conform action on packets that conform to the rate limit set on the subscriber circuit.

rbnQosSubsRLClassExceedOctets


rbnQosSubscriberRLClassStatsEntry 9


1.3.6.1.4.1.2352.2.22.1.5.1.9

Counter64

N/A

The number of octets that exceed the rate limit set on the subscriber circuit.

rbnQosSubsRLClassExceedPkts


rbnQosSubscriberRLClassStatsEntry 10


1.3.6.1.4.1.2352.2.22.1.5.1.10

Counter64

N/A

The number of packets that exceed the rate limit set on the subscriber circuit.

rbnQosSubsRLClassExceedDroppedOctets


rbnQosSubscriberRLClassStatsEntry 11


1.3.6.1.4.1.2352.2.22.1.5.1.11

Counter64

N/A

The number of octets dropped due to the application of an exceed action on packets that exceed the rate limit set on the subscriber circuit.

rbnQosSubsRLClassExceedDroppedPkts


rbnQosSubscriberRLClassStatsEntry 12


1.3.6.1.4.1.2352.2.22.1.5.1.12

Counter64

N/A

The number of packets dropped due to the application of an exceed action on packets that exceed the rate limit set on the subscriber circuit.

rbnQosSubsRLClassViolateOctets


rbnQosSubscriberRLClassStatsEntry 13


1.3.6.1.4.1.2352.2.22.1.5.1.13

Counter64

N/A

The number of octets that violate the normal and maximum burst sizes on the subscriber circuit.

rbnQosSubsRLClassViolatePkts


rbnQosSubscriberRLClassStatsEntry 14


1.3.6.1.4.1.2352.2.22.1.5.1.14

Counter64

N/A

The number of packets that violate the normal and maximum burst sizes on the subscriber circuit.

rbnQosSubsRLClassViolateDroppedOctets


rbnQosSubscriberRLClassStatsEntry 15


1.3.6.1.4.1.2352.2.22.1.5.1.15

Counter64

N/A

The number of octets dropped due to the application of a violate action on packets that violate the normal and maximum burst sizes on the subscriber circuit.

rbnQosSubsRLClassViolateDroppedPkts


rbnQosSubscriberRLClassStatsEntry 16


1.3.6.1.4.1.2352.2.22.1.5.1.16

Counter64

N/A

The number of packets dropped due to the application of a violate action on packets that violate the normal and maximum burst sizes on the subscriber circuit.

1.29.6   rbnQosHierarchicalPolicyStatsTable

A table of drop counters for child circuits of hierarchical QOS policies applied to the child.

Index: ifIndex, rbnQosHierarchicalPolicyType

Table 63 describes the attributes in rbnQosHierarchicalPolicyStatsTable. All objects in the table are read-only.

Table 63    Objects in rbnQosHierarchicalPolicyStatsTable

Object and Object Identifier

Type

Value Range

Description

rbnQosHierarchicalPolicyName


rbnQosHierarchicalPolicyStatsEntry 2


1.3.6.1.4.1.2352.2.22.1.6.1.2

SnmpAdminString

SIZE (1–39)

Name of the hierarchical parent policy applied to the child circuit.

rbnQosHierarchicalPolicyDroppedOctets


rbnQosHierarchicalPolicyStatsEntry 3


1.3.6.1.4.1.2352.2.22.1.6.1.3

Counter64

N/A

The number of octets dropped due to the hierarchical parent's policy applied to the child circuit.

rbnQosHierarchicalPolicyDroppedPkts


rbnQosHierarchicalPolicyStatsEntry 4


1.3.6.1.4.1.2352.2.22.1.6.1.4

Counter64

N/A

The number of packets dropped due to the hierarchical parent's policy applied to the child circuit.

1.29.7   rbnQosHierarchicalPClassStatsTable

A table of drop counters for child circuits of hierarchical QOS policy classes applied to the child.

Index: ifIndex, rbnQosHierarchicalPolicyType, rbnQosHierarchicalPClassId

Table 64 describes the attributes in rbnQosHierarchicalPClassStatsTable. All objects in the table are read-only.

Table 64    Objects in rbnQosHierarchicalPClassStatsTable

Object and Object Identifier

Type

Value Range

Description

rbnQosHierarchicalPClassName


rbnQosHierarchicalPClassStatsEntry 2


1.3.6.1.4.1.2352.2.22.1.7.1.2

SnmpAdminString

SIZE (1–39)

Name of the hierarchical parent policy class that is applied to the child circuit.

rbnQosHierarchicalPClassDroppedOctets


rbnQosHierarchicalPClassStatsEntry 3


1.3.6.1.4.1.2352.2.22.1.7.1.3

Counter64

N/A

The number of octets dropped due to the hierarchical parent's policy class applied to the child circuit.

rbnQosHierarchicalPClassDroppedPkts


rbnQosHierarchicalPClassStatsEntry 4


1.3.6.1.4.1.2352.2.22.1.7.1.4

Counter64

N/A

The number of packets dropped due to the hierarchical parent's policy class applied to the child circuit.

1.30   RBN-RADIUS-MIB

Defines additional objects and notifications for managing the Remote Authentication Dial-In User Service (RADIUS) authentication and accounting servers in use by the SmartEdge router.

The following sections describe objects for RBN-RADIUS-MIB.

1.30.1   RADIUS Authorization Objects

Table 65 describes the RADIUS authorization objects for RBN-RADIUS-MIB. All objects in the table are read-only.

Table 65    RADIUS Authorization Objects

Object and Object Identifier

Type

Value Range

Description

rbnRadiusAuthPktTimeout


rbnRadiusAuthObjects 1


1.3.6.1.4.1.2352.2.32.1.1.1

Unsigned32

1– 2147483647

The maximum amount of time to wait for a response from a RADIUS authorization server before assuming the packet was lost.

rbnRadiusAuthSrvTimeout


rbnRadiusAuthObjects 2


1.3.6.1.4.1.2352.2.32.1.1.2

Unsigned32

0– 2147483647

The maximum amount of time to wait for any response from a RADIUS authorization server before assuming the server is unreachable. A value of '0' indicates that there is no timeout value. In this case, a server is considered to be unreachable when no response is received within the rbnRadiusAuthPktTimeout object window.

rbnRadiusAuthDeadtime


rbnRadiusAuthObjects 3


1.3.6.1.4.1.2352.2.32.1.1.3

Unsigned32

0–65535

After a RADIUS authorization server has been transitioned to 'down,' it is assumed to be unreachable for this interval. After that point, the system can start sending requests to the server again. A value of '0' indicates the system can start sending requests to the server immediately.

rbnRadiusAuthTries


rbnRadiusAuthObjects 4


1.3.6.1.4.1.2352.2.32.1.1.4

Unsigned32

1– 2147483647

The number of times the system attempts to transmit an authorization request to a RADIUS server. If multiple RADIUS authorization servers have been configured, retransmissions cycle through the other servers before being retransmitted to the server that originally failed to respond.

rbnRadiusAuthStripDomain


rbnRadiusAuthObjects 6


1.3.6.1.4.1.2352.2.32.1.1.6

TruthValue

1—true


2—false

If this object is false, the entire username, including the domain name, is sent to the RADIUS server. If true, the domain portion of a structured username is stripped before relaying a request to a RADIUS server.

1.30.2   RADIUS Accounting Objects

Table 66 describes the RADIUS accounting objects for RBN-RADIUS-MIB. All objects in the table are read-only.

Table 66    RADIUS Accounting Objects

Object and Object Identifier

Type

Value Range

Description

rbnRadiusAcctPktTimeout


rbnRadiusAcctObjects 1


1.3.6.1.4.1.2352.2.32.1.2.1

Unsigned32

1– 2147483647

The maximum amount of time to wait for a response from a RADIUS accounting server before assuming the packet was lost. Note: if the system is using a RADIUS server for both authorization and accounting, this object's value is ignored for that server. Instead, the value of the rbnRadiusAuthPktTimeout object is used for all requests going to that server.

rbnRadiusAcctSrvTimeout


rbnRadiusAcctObjects 2


1.3.6.1.4.1.2352.2.32.1.2.2

Unsigned32

0– 2147483647

The maximum amount of time to wait for any response from a RADIUS accounting server before assuming the server is unreachable. A value of '0' indicates that there is no timeout value. In this case, a server is considered to be unreachable when no response is received within the rbnRadiusAcctPktTimeout object window. Note: if the system is using a RADIUS server for both authorization and accounting, this object's value is ignored for that server. Instead the value of the rbnRadiusAuthSrvTimeout object will be used for that server

rbnRadiusAcctDeadtime


rbnRadiusAcctObjects 3


1.3.6.1.4.1.2352.2.32.1.2.3

Unsigned32

0–65535

After a RADIUS accounting server has been transitioned to 'down,' it is assumed to be unreachable for this interval. After that point, the system can start sending accounting records to the server again. A value of '0' indicates the system can start sending records to the server immediately. If the system is using a RADIUS server for both authorization and accounting, this object's value is ignored for that server. Instead, the value of the rbnRadiusAuthDeadtime object is used for that server.

rbnRadiusAcctTries


rbnRadiusAcctObjects 4


1.3.6.1.4.1.2352.2.32.1.2.4

Unsigned32

1– 2147483647

The number of times the system attempts to transmit an accounting record to a RADIUS server. If multiple RADIUS accounting servers have been configured, retransmissions cycle through the other servers before being retransmitted to the server that originally failed to respond. If the system is using a RADIUS server for both authorization and accounting, this object's value is ignored for that server. Instead, the value of the rbnRadiusAuthTries object is used for that server.

rbnRadiusAcctStripDomain


rbnRadiusAcctObjects 6


1.3.6.1.4.1.2352.2.32.1.2.6

TruthValue

1—true


2—false

If this object is false, the entire username, including the domain name, is sent to the RADIUS server. If true, the domain portion of a structured username is stripped before relaying a request to a RADIUS server.

1.30.3   RADIUS Notification Objects

Table 67 describes the RADIUS notification objects for RBN-RADIUS-MIB. All objects in the table are read-only unless otherwise specified.

Table 67    RADIUS Notification Objects

Object and Object Identifier

Type

Value Range

Description

rbnRadiusClientPort


1.3.6.1.4.1.2352.2.32.1.3.1

Unsigned32

1024– 65535

A system can be configured to use a range of source TCP/IP ports when sending requests to a RADIUS server. When a server transitions to 'up' or 'down' and a state-change notification is generated, an instance of this object is included to indicate which source port was used when the server changed state. This object is accessible-for-notify.

rbnRadiusContext


rbnRadiusNotifyObjects 2


1.3.6.1.4.1.2352.2.32.1.3.2

SnmpAdminString

SIZE (1–63)

The name of the context in which this server is configured. This object is accessible-for-notify.

rbnRadiusReason


rbnRadiusNotifyObjects 3


1.3.6.1.4.1.2352.2.32.1.3.3

RbnRadiusServerReason


Integer

1—responding


2—packetTimeout


3—serverTimeout


4—portDown

The reason for the server's last state change. This object is accessible-for-notify.

rbnRadiusUsername


rbnRadiusNotifyObjects 4


1.3.6.1.4.1.2352.2.32.1.3.4

SnmpAdminString

SIZE (0–128)

The name of the user the system was trying to authenticate or send accounting information for when the RADIUS server transitioned to 'down'. Note: the 'username' is only valid when transitioning due to a packet-level timeout. When transitioning due to any other reason, the value for this object is a zero-length string. This object is accessible-for-notify.

1.30.4   rbnRadiusAuthSrvTable

This table augments the radiusAuthServerTable. All entries that exist in that table have a corresponding entry in this table.

Index: radiusAuthServerIndex

Table 68 describes the attributes in rbnRadiusAuthSrvTable. All objects in the table are read-only.

Table 68    Objects in rbnRadiusAuthSrvTable

Object and Object Identifier

Type

Value Range

Description

rbnRadiusAuthSrvState


rbnRadiusAuthSrvEntry 1


1.3.6.1.4.1.2352.2.32.1.1.5.1.1

RbnRadiusServerState


Integer

1—unknown


2—up


3—down

The current state of the RADIUS server.

rbnRadiusAuthSrvLastChange


rbnRadiusAuthSrvEntry 2


1.3.6.1.4.1.2352.2.32.1.1.5.1.2

TimeStamp

N/A

The value of sysUpTime when this server last changed state. If rbnRadiusAuthSrvState is 'unknown,' this is effectively the value of the sysUpTime object when this server was initially configured.

rbnRadiusAuthSrvCounterResetTime


rbnRadiusAuthSrvEntry 3


1.3.6.1.4.1.2352.2.32.1.1.5.1.3

TimeStamp

N/A

The value of sysUpTime on the most recent occasion when any of the counters for this RADIUS server experienced a discontinuity. This includes counters in this table as well as those in the radiusAuthServerTable object.

rbnRadiusAuthSrvSendErrors


rbnRadiusAuthSrvEntry 4


1.3.6.1.4.1.2352.2.32.1.1.5.1.4

Counter32

N/A

The number of packets destined to this RADIUS server that could not be transmitted due to an error. Discontinuities in the value of this counter are indicated by the value of the rbnRadiusAuthSrvCounterResetTime object.

1.30.5   rbnRadiusAcctSrvTable

This table augments the radiusAccServerTable. All entries that exist in that table have a corresponding entry in this table.

Index: radiusAccServerIndex

Table 69 describes the attributes in rbnRadiusAcctSrvTable. All objects in the table are read-only.

Table 69    Objects in rbnRadiusAcctSrvTable

Object and Object Identifier

Type

Value Range

Description

rbnRadiusAcctSrvState


rbnRadiusAcctSrvEntry 1


1.3.6.1.4.1.2352.2.32.1.2.5.1.1

RbnRadiusServerState


Integer

1—unknown


2—up


3—down

The current state of the RADIUS server.

rbnRadiusAcctSrvLastChange


rbnRadiusAcctSrvEntry 2


1.3.6.1.4.1.2352.2.32.1.2.5.1.2

TimeStamp

N/A

The value of the sysUpTime object when this server last changed state. If the rbnRadiusAcctSrvState object is 'unknown,‘ this is effectively the value of the sysUpTime object when this server was initially configured.

rbnRadiusAcctSrvCounterResetTime


rbnRadiusAcctSrvEntry 3


1.3.6.1.4.1.2352.2.32.1.2.5.1.3

TimeStamp

N/A

The value of the sysUpTime object on the most recent occasion when any of the counters for this RADIUS server experienced a discontinuity. Note: this includes counters in this table as well as those in the radiusAccServerTable object.

rbnRadiusAcctSrvSendErrors


rbnRadiusAcctSrvEntry 4


1.3.6.1.4.1.2352.2.32.1.2.5.1.4

Counter32

N/A

The number of packets destined to this RADIUS server which could not be transmitted due to an error. Discontinuities in the value of this counter are indicated by the value of the rbnRadiusAcctSrvCounterResetTime object.

1.31   RBN-SFP-MIB

Defines objects for managing the Small Form Factor Pluggable (SFP) transceivers.

1.31.1   rbnSfpAlarmActiveTable

A table containing the SFP alarms currently active on the SFP.

Index: rbnSfpActiveAlarmIndex

Table 70 describes the attributes in rbnSfpAlarmActiveTable.

Table 70    Objects in rbnStackedVlanAggrStatsTable

Object and Object Identifier

Type

Value Range

Description

rbnSfpActiveAlarmIndex


rbnSfpAlarmActiveEntry 1


1.3.6.1.4.1.2352.2.49.1.1.1.1

Unsigned32

(1..4294967295)

A monotonically increasing integer index. It wraps back to 1 after it reaches its maximum value.

rbnSfpAlarmCardSlot


rbnSfpAlarmActiveEntry 2


1.3.6.1.4.1.2352.2.49.1.1.1.2

Unsigned32

 

The chassis slot number in which the card is present where the SFP plugged in.

rbnSfpAlarmPort


rbnSfpAlarmActiveEntry 3


1.3.6.1.4.1.2352.2.49.1.1.1.3

Unsigned32

 

The port number where the SFP plugged in.

rbnSfpAlarmId


rbnSfpAlarmActiveEntry 4


1.3.6.1.4.1.2352.2.49.1.1.1.4

INTEGER

1—unknown


2—cpFail


3— cpBackplaneFail


4—diagFail


5—voltageFail


6—controllerSwitchFail


7—controllerTempCritical


8—controllerFail


9—controllerDiagFail


10—cpPowerOnDiagFail


11—controllerPowerOnDiagFail


12—cpOverheat


13—controllerOverheat


14—backplaneclkfail


15—btciferror


16—btcnotready


17—cpbackplanedegrade


18—cpcardcodemismatch


19—cpmismatch


20—cpmissing


21—cpresetcomplete


22—downloadcompleted


23—downloadfailed


24—syncfail


25—backupfail


26—controllercardcodemismatch


27—controllercardtypemismatch


28—controllermissing


29—controlleroverheat


30—controllerswitchauto


31—controllerswitchcompleted


32—controllerswitchexfailed


33—controllerswitchforced


34—controllerswitchmanual


35—localfantrayinventfail


36—localinventfail


37—localbackplaneinventfail


38—lostm2m


39—nonvolatilememfail


40—peerhwincompatiblep


41—peerinventfail


42—peermodeincompatible

An identifier for the alarm.

rbnSfpAlarmId (continued)


rbnSfpAlarmActiveEntry 4


1.3.6.1.4.1.2352.2.49.1.1.1.4

INTEGER

43—peersharedformatmismatch


44—rtclockfail


45—mic1missing


46—mic2missing


47—mic1mismatch


48—mic2mismatch


49—mic1voltagefailure


50—mic2voltagefailure


51—mic1overheat


52—mic2overheat


53—mic1failure


54—mic2failure


55—mic1podfail


56—mic2podfail


57—mic1diagnosticfail


58—mic2diagnosticfail


59—ethtransceiverrxpowerhi


60—ethtransceiverrxpowerlo


61—ethtransceivertemphi


62—ethtransceivertemplo


63—ethtranceivervoltagehi


64—ethtranceivervoltagelo


65—ethtransceiverbiashi


66—ethtransceiverbiaslo


67—ethtransceivertxpowerhi


68—ethtransceivertxpowerlo


69—ethtransceiveraux1hi


70—ethtransceiveraux1lo


71—ethtransceiveraux2hi


72—ethtransceiveraux2lo


73— ethtransceiverlvcc5hi


74—ethtransceiverlvcc5lo


75—ethtransceiverlvcc3hi


76—ethtransceiverlvcc3lo


77—ethtransceiverlvcc2hi


78—ethtransceiverlvcc2lo


79—controllerbsdl2cacheerror


80—controllervxwl2cacheerror

An identifier for the alarm.

rbnSfpAlarmSeverity


rbnSfpAlarmActiveEntry 5


1.3.6.1.4.1.2352.2.49.1.1.1.5

INTEGER

1—cleared


2—indeterminate


3—critical


4—major


5—minor


6—warning

The perceived severity of the alarm.

rbnSfpAlarmType


rbnSfpAlarmActiveEntry 6


1.3.6.1.4.1.2352.2.49.1.1.1.6

IINTEGER

1—other


2—communicationsAlarm


3—qualityOfServiceAlarm


4—processingErrorAlarm


5—equipmentAlarm


6—environmentalAlarm


7—integrityViolation


8—operationalViolation


9—physicalViolation


10—securityServiceOrMechanismViolation


11—timeDomainViolation

The type of the alarm.

rbnSfpAlarmDateAndTime


rbnSfpAlarmActiveEntry 7


1.3.6.1.4.1.2352.2.49.1.1.1.7

DateAndTime

OctetString

The local date and time when the alarm was raised

rbnSfpAlarmDescription


rbnSfpAlarmActiveEntry 8


1.3.6.1.4.1.2352.2.49.1.1.1.8

SnmpAdminString

OctetString (0..64)

A text string which conveys additional information about the alarm.

rbnSfpAlarmProbableCause


rbnSfpAlarmActiveEntry 9


1.3.6.1.4.1.2352.2.49.1.1.1.9

INTEGER

1—aIS


2—callSetUpFailure


3—degradedSignal


4—farEndReceiverFailure


5—framingError


6—lossOfFrame


7—lossOfPointer


8—lossOfSignal


9—payloadTypeMismatch


10—transmissionError


11—remoteAlarmInterface


12—excessiveBER


13—pathTraceMismatch


14—unavailable


15—signalLabelMismatch


16—lossOfMultiFrame


17—receiveFailure


18—transmitFailure


19—modulationFailure


20—demodulationFailure


21—broadcastChannelFailure


22—connectionEstablishmentError


23—invalidMessageReceived


24—localNodeTransmissionError


25—remoteNodeTransmissionError


26—routingFailure


51—backplaneFailure


52—dataSetProblem


53—equipmentIdentifierDuplication


54—externalIFDeviceProblem


55—lineCardProblem


56—multiplexerProblem


57—nEIdentifierDuplication


58—powerProblem


59—processorProblem


60—protectionPathFailure


61—receiverFailure


62—replaceableUnitMissing


63—replaceableUnitTypeMismatch


64—synchronizationSourceMismatch


65—terminalProblem


66—timingProblem

The probable cause for this alarm.

 

INTEGER

67—transmitterFailure


68—trunkCardProblem


69—replaceableUnitProblem


70—realTimeClockFailure


71—antennaFailure


72—batteryChargingFailure


73—diskFailure


74—frequencyHoppingFailure


75—iODeviceError


76—lossOfSynchronisation


77—lossOfRedundancy


78—powerSupplyFailure


79—signalQualityEvaluationFailure


80—tranceiverFailure


81—protectionMechanismFailure


82—protectingResourceFailure


101—airCompressorFailure


102—airConditioningFailure


103—airDryerFailure


104—batteryDischarging


105—batteryFailure


106—commercialPowerFailure


107—coolingFanFailure


108—engineFailure


109—fireDetectorFailure


110—fuseFailure


111—generatorFailure


112—lowBatteryThreshold


113—pumpFailure


114—rectifierFailure


115—rectifierHighVoltage


116—rectifierLowFVoltage


117—ventilationsSystemFailure


118—enclosureDoorOpen


119—explosiveGas120—fire


121—flood


122—highHumidity


123—highTemperature


124—highWind


125—iceBuildUp


126—intrusionDetection

The probable cause for this alarm.

 

INTEGER

127—lowFuel


128—lowHumidity


129—lowCablePressure


130—lowTemperatue


131—lowWater


132—smoke


133—toxicGas


134—coolingSystemFailure


135—externalEquipmentFailure


136—externalPointFailure


151—storageCapacityProblem


152—memoryMismatch


153—corruptData


154—outOfCPUCycles


155—sfwrEnvironmentProblem


156—sfwrDownloadFailure

The probable cause for this alarm.

 

INTEGER

157—lossOfRealTimel


158—applicationSubsystemFailure


159—configurationOrCustomisationError


160—databaseInconsistency


161—fileError


162—outOfMemory


163—softwareError


164—timeoutExpired


165—underlayingResourceUnavailable


166—versionMismatch


201—bandwidthReduced


202—congestion


203—excessiveErrorRate


204—excessiveResponseTime


205—excessiveRetransmissionRate


206—reducedLoggingCapability


207—systemResourcesOverload


500—adapterError


501—applicationSubsystemFailture


502—bandwidthReducedX733


503—callEstablishmentError


504—communicationsProtocolError


505—communicationsSubsystemFailure


506—configurationOrCustomizationError


507—congestionX733


508—coruptData


509—cpuCyclesLimitExceeded


510—dataSetOrModemError


511—degradedSignalX733


512—dteDceInterfaceError


513—enclosureDoorOpenX733


514—equipmentMalfunction


515—excessiveVibration


516—fileErrorX733


517—fireDetected


518—framingErrorX733


519—heatingVentCoolingSystemProblem


520—humidityUnacceptable


521—inputOutputDeviceError

The probable cause for this alarm.

 

INTEGER

522—inputDeviceError


523—lanError


524—leakDetected


525—localNodeTransmissionErrorX733


526—lossOfFrameX733


527—lossOfSignalX733


528—materialSupplyExhausted


529—multiplexerProblemX733


530—outOfMemoryX733


531—ouputDeviceError


532—performanceDegraded


533—powerProblems


534—pressureUnacceptable


535—processorProblems


536—pumpFailureX733


537—queueSizeExceeded


538—receiveFailureX733


539—receiverFailureX733


540—remoteNodeTransmissionErrorX733


541—resourceAtOrNearingCapacity


542—responseTimeExecessive


543—retransmissionRateExcessive


544—softwareErrorX733


545—softwareProgramAbnormallyTerminated


546—softwareProgramError


547—storageCapacityProblemX733


548—temperatureUnacceptable


549—thresholdCrossed


550—timingProblemX733


551—toxicLeakDetected


552—transmitFailureX733


553—transmiterFailure


554—underlyingResourceUnavailable


555—versionMismatchX733


600—authenticationFailure


601—breachOfConfidentiality


602—cableTamper


603—delayedInformation


604—denialOfService


605—duplicateInformation

The probable cause for this alarm.

 

INTEGER

606—informationMissing


607—informationModificationDetectede


608—informationOutOfSequence


609—keyExpired


610—nonRepudiationFailure


611—outOfHoursActivity


612—outOfServic


613—proceduralError


614—unauthorizedAccessAttempt


615—unexpectedInformation


1024—other

The probable cause for this alarm.

rbnSfpAlarmServiceAffecting


rbnSfpAlarmActiveEntry 10


1.3.6.1.4.1.2352.2.49.1.1.1.10

INTEGER

1—yes


2—no

Indicates whether the alarm is perceived to be service impacting.

1.32   RBN-SSE-MIB

Defines objects necessary to support the management of SmartEdge Server Engine (SSE) file server groups, partitions and corresponding alarms

1.32.1   rbnFSGroupTable

File-server group is a logical abstraction of a physical file server. This table lists the file server groups that have been configured on the system.

Index: rbnFSGroupName

Table 71 describes the attributes in rbnFSGroupTable. All objects in the table are read-only.

Table 71    Objects in rbnFSGroupTable

Object and Object Identifier

Type

Value Range

Description

rbnFSGroupName


rbnFSGroupEntry 1

SnmpAdminString

SIZE (1..16)

A textual name for the File Server Group.

rbnFSGroupState


rbnFSGroupEntry 2

INTEGER

0—unknown


1—up


2—down


3—partial


4—stale


5— noCard


6—unassigned

Service state of the File Server Group.

rbnFSGroupMode


rbnFSGroupEntry 3

INTEGER

1—diskRedundancy


2— networkRedundancy


3—nonRedundant

The operational mode. DiskRedundancy is where each hard disk on a single file-server card mirrors the other and when one fails the other takes over automatically. NetworkRedundancy is a one file-server mirroring the other in the same chassis. One of the file-servers will be in active state while the other is standby or backup. NonRedundant is when one or two hard disks serve as a generic disk.

rbnFSGroupRaidMode


rbnFSGroupEntry 4

INTEGER

0—unknown


1—raid0


2—raid1


3—independent

Operational mode of the disks. The option RAID0 is where the operational mode must use 2 disks. RAID1 implies using 2 disks, although 1 could be un-plugged. Independent (standalone) is either 1 or 2 disks.

rbnFSGroupRevert


rbnFSGroupEntry 5

TruthValue

1—true


2—false

The reverting mode of the File Server Group. Revert back to original primary/secondary relationship if in reverted mode (that is this object has the value true(1)).

rbnFSPrimarySlot


rbnFSGroupEntry 6

RbnSlot


Unsigned32

(0–255)

The chassis slot number in which the primary SSE card is present.

rbnFSSecondarySlot


rbnFSGroupEntry 7

RbnSlot


Unsigned32

(0–255)

The chassis slot number in which the secondary SSE card is present.

rbnFSActiveSlot


rbnFSGroupEntry 8

RbnSlot


Unsigned32

(0–255)

The slot number in which the active SSE card is present.

1.32.2   rbnFSPartitionTable

This table lists the Partitions that have been 212 configured on the system.

Index: rbnFSGroupName, rbnFSPartitionName

Table 72 describes the attributes in rbnFSPartitionTable. All objects in the table are read-only.

Table 72    Objects in rbnFSPartitionTable

Object and Object Identifier

Type

Value Range

Description

rbnFSPartitionName


rbnFSPartitionEntry 1

SnmpAdminString

SIZE (1..16)

A textual name for the Partition.

rbnFSPartitionState


rbnFSPartitionEntry 2

INTEGER

1—up


2—down


3—stale

Operational status of the partition.

rbnFSPartitionSize


rbnFSPartitionEntry 3

Unsigned32

1..4294967295

Size of the partition in GBytes.

rbnFSPartitionDisk


rbnFSPartitionEntry 4

Unsigned32

1..10

Disk ID of the disk (disk num) where the partition is located. For SSE, 0 for DISK_1, 1 for DISK_2 and 2 for DISK_ALL will be used.

rbnFSPartitionMirrored


rbnFSPartitionEntry 5

INTEGER

1—enabled


2—disabled\


3—notApplicable

Mirror data to standby disk, if network redundancy is configured.

rbnFSPartitionRaiseTriggerPercentage


rbnFSPartitionEntry 6

RbnPercentage

50..100

Partition capacity used in percentage to trigger alarm. Raise percentage of 100 indicates alarm is triggered when the partition is completely full.

rbnFSPartitionClearTriggerPercentage


rbnFSPartitionEntry 7

RbnPercentage

10..100

Specifies the capacity percentage for when the alarm is cleared. Clear percentage of 10 indicates alarm is triggered when partition is at 10% below raise percentage.

1.32.3   RBN-SSE-MIB Objects

Table 74 the general objects for RBN-SSE-MIB.

Table 73    RBN-SSE-MIB Objects

Object and Object Identifier

Type

Value Range

Description

rbnSseAlarmDateAndTime


rbnSseMIBObjects 3

DateAndTime

N/A

The local date and time when the alarm was raised

rbnSseAlarmSeverity


rbnSseMIBObjects 4

ItuPerceivedSeverity


INTEGER

1—cleared


2—indeterminate


3—critical


4—major


5—minor


6—warning

The perceived severity of the alarm.

rbnSseAlarmProbableCause


rbnSseMIBObjects 5

IANAItuProbableCause


INTEGER

1—aIS


2—callSetUpFailure


3—degradedSignal


4—farEndReceiverFailure


5—framingError


6—lossOfFrame


7—lossOfPointer


8—lossOfSignal


9—payloadTypeMismatch


10—transmissionError


11—remoteAlarmInterface


12—excessiveBER


13—pathTraceMismatch


14—unavailable


15—signalLabelMismatch


16—lossOfMultiFrame


17—receiveFailure


18—transmitFailure


19—modulationFailure


20—demodulationFailure


21—broadcastChannelFailure


22—connectionEstablishmentError


23—invalidMessageReceived


24—localNodeTransmissionError


25—remoteNodeTransmissionError


26—routingFailure


51—backplaneFailure


52—dataSetProblem


53—equipmentIdentifierDuplication


54—externalIFDeviceProblem


55—lineCardProblem


56—multiplexerProblem


57—nEIdentifierDuplication


58—powerProblem


59—processorProblem


60—protectionPathFailure


61—receiverFailure


62—replaceableUnitMissing


63—replaceableUnitTypeMismatch


64—synchronizationSourceMismatch

The probable cause for this alarm.

   

65—terminalProblem


66—timingProblem


67—transmitterFailure


68—trunkCardProblem


69—replaceableUnitProblem


70—realTimeClockFailure


71—antennaFailure


72—batteryChargingFailure


73—diskFailure


74—frequencyHoppingFailure


75—iODeviceError


76—lossOfSynchronisation


77—lossOfRedundancy


78—powerSupplyFailure


79—signalQualityEvaluationFailure


80—tranceiverFailure


81—protectionMechanismFailure


82—protectingResourceFailure


101—airCompressorFailure


102—airConditioningFailure


103—airDryerFailure


104—batteryDischarging


105—batteryFailure


106—commercialPowerFailure


107—coolingFanFailure


108—engineFailure


109—fireDetectorFailure


110—fuseFailure


111—generatorFailure


112—lowBatteryThreshold


113—pumpFailure


114—rectifierFailure


115—rectifierHighVoltage


116—rectifierLowFVoltage


117—ventilationsSystemFailure


118—enclosureDoorOpen


119—explosiveGas120—fire


121—flood


122—highHumidity


123—highTemperature

 
   

124—highWind


125—iceBuildUp


126—intrusionDetection


127—lowFuel


128—lowHumidity


129—lowCablePressure


130—lowTemperatue


131—lowWater


132—smoke


133—toxicGas


134—coolingSystemFailure


135—externalEquipmentFailure


136—externalPointFailure


151—storageCapacityProblem


152—memoryMismatch


153—corruptData


154—outOfCPUCycles


155—sfwrEnvironmentProblem


156—sfwrDownloadFailure


157—lossOfRealTimel


158—applicationSubsystemFailure


159—configurationOrCustomisationError


160—databaseInconsistency


161—fileError


162—outOfMemory


163—softwareError


164—timeoutExpired


165—underlayingResourceUnavailable


166—versionMismatch


201—bandwidthReduced


202—congestion


203—excessiveErrorRate


204—excessiveResponseTime


205—excessiveRetransmissionRate


206—reducedLoggingCapability


207—systemResourcesOverload


500—adapterError


501—applicationSubsystemFailture

 
   

502—bandwidthReducedX733


503—callEstablishmentError


504—communicationsProtocolError


505—communicationsSubsystemFailure


506—configurationOrCustomizationError


507—congestionX733


508—coruptData


509—cpuCyclesLimitExceeded


510—dataSetOrModemError


511—degradedSignalX733


512—dteDceInterfaceError


513—enclosureDoorOpenX733


514—equipmentMalfunction


515—excessiveVibration


516—fileErrorX733


517—fireDetected


518—framingErrorX733


519—heatingVentCoolingSystemProblem


520—humidityUnacceptable


521—inputOutputDeviceError


522—inputDeviceError


523—lanError


524—leakDetected


525—localNodeTransmissionErrorX733


526—lossOfFrameX733


527—lossOfSignalX733


528—materialSupplyExhausted


529—multiplexerProblemX733


530—outOfMemoryX733


531—ouputDeviceError


532—performanceDegraded


533—powerProblems


534—pressureUnacceptable


535—processorProblems


536—pumpFailureX733


537—queueSizeExceeded


538—receiveFailureX733


539—receiverFailureX733


540—remoteNodeTransmissionErrorX733


541—resourceAtOrNearingCapacity


542—responseTimeExecessive


543—retransmissionRateExcessive


544—softwareErrorX733

 
   

545—softwareProgramAbnormallyTerminated


546—softwareProgramError


547—storageCapacityProblemX733


548—temperatureUnacceptable


549—thresholdCrossed


550—timingProblemX733


551—toxicLeakDetected


552—transmitFailureX733


553—transmiterFailure


554—underlyingResourceUnavailable


555—versionMismatchX733


600—authenticationFailure


601—breachOfConfidentiality


602—cableTamper


603—delayedInformation


604—denialOfService


605—duplicateInformation


606—informationMissing


607—informationModificationDetectede


608—informationOutOfSequence


609—keyExpired


610—nonRepudiationFailure


611—outOfHoursActivity


612—outOfServic


613—proceduralError


614—unauthorizedAccessAttempt


615—unexpectedInformation


1024—other

 

rbnSseEventType


rbnSseMIBObjects 6

IANAItuEventType


INTEGER

1—other


2—communicationsAlarm


3—qualityOfServiceAlarm


4—processingErrorAlarm


5—equipmentAlarm


6—environmentalAlarm


7—integrityViolation


8—operationalViolation


9—physicalViolation


10—securityServiceOrMechanismViolation


11—timeDomainViolation

The type of the alarm.

rbnSseAlarmDescription


rbnSseMIBObjects 7

SnmpAdminString

SIZE(0..64)

A text string which conveys additional information about the alarm.

1.33   RBN-STACKEDVLAN-MIB

Defines objects for managing the interfaces in the stacked VLAN.

1.33.1   rbnStackedVlanAggrStatsTable

A table containing aggregated statistics of inner VLAN's related to an outer VLAN.

Index: rbnStackedVlanIndex

Table 74 describes the attributes in rbnStackedVlanAggrStatsTable. All objects in the table are read-only.

Table 74    Objects in rbnStackedVlanAggrStatsTable

Object and Object Identifier

Type

Value Range

Description

rbnStackedVlanHCInOctets


rbnStackedVlanAggrStatsEntry 2


1.3.6.1.4.1.2352.2.40.1.1.1.2

Counter64

N/A

The aggregate of the total number of octets received on each outer VLAN and its inner VLANs, including framing characters.

rbnStackedVlanHCInUcastPkts


rbnStackedVlanAggrStatsEntry 3


1.3.6.1.4.1.2352.2.40.1.1.1.3

Counter64

N/A

The aggregate of the number of packets, delivered by this sublayer to a higher layer or sublayer, which were not addressed to a multicast or broadcast address at this sublayer for each outer VLAN and its inner VLANs.

rbnStackedVlanHCInMulticastPkts


rbnStackedVlanAggrStatsEntry 4


1.3.6.1.4.1.2352.2.40.1.1.1.4

Counter64

N/A

The aggregate number of packets, delivered by this sublayer to a higher layer or sublayer, that were addressed to a multicast address at this sublayer for each outer VLAN and its inner VLANs. For a MAC layer protocol, this includes both Group and Functional addresses.

rbnStackedVlanHCInBroadcastPkts


rbnStackedVlanAggrStatsEntry 5


1.3.6.1.4.1.2352.2.40.1.1.1.5

Counter64

N/A

The aggregate number of packets, delivered by this sublayer to a higher layer or sublayer, that were addressed to a broadcast address at this sublayer for each outer VLAN and its inner VLANs.

rbnStackedVlanHCOutOctets


rbnStackedVlanAggrStatsEntry 6


1.3.6.1.4.1.2352.2.40.1.1.1.6

Counter64

N/A

The aggregate of the total number of octets transmitted out of the interface, including framing characters for each outer VLAN and its inner VLANs.

rbnStackedVlanHCOutUcastPkts


rbnStackedVlanAggrStatsEntry 7


1.3.6.1.4.1.2352.2.40.1.1.1.7

Counter64

N/A

The aggregate of the total number of packets that higher-level protocols requested be transmitted, and that were not addressed to a multicast or broadcast address at this sublayer, including those that were discarded or not sent for each outer VLAN and its inner VLANs.

rbnStackedVlanHCOutMulticastPkts


rbnStackedVlanAggrStatsEntry 8


1.3.6.1.4.1.2352.2.40.1.1.1.8

Counter64

N/A

The aggregate of the total number of packets that higher-level protocols requested be transmitted, and that were addressed to a multicast address at this sublayer, including those that were discarded or not sent for each outer VLAN and its inner VLANs. For a MAC layer protocol, this includes both Group and Functional addresses.

rbnStackedVlanHCOutBroadcastPkts


rbnStackedVlanAggrStatsEntry 9


1.3.6.1.4.1.2352.2.40.1.1.1.9

Counter64

N/A

The aggregate of the total number of packets that higher-level protocols requested be transmitted, and that were addressed to a broadcast address at this sublayer, including those that were discarded or not sent for each outer VLAN and its inner VLANs.

1.34   RBN-SUBSCRIBER-ACTIVE-MIB

Defines the objects used to support the management of active subscribers in the SmartEdge product family. Related commands include the subscriber and show subscriber commands.

The following sections contain object information for RBN-SUBSCRIBER-ACTIVE-MIB.

1.34.1   RBN-SUBSCRIBER-ACTIVE-MIB Objects

Table 75 describes the objects in RBN-SUBSCRIBER-ACTIVE-MIB. All objects in the table are read-only.

Table 75    Objects in RBN-SUBSCRIBER-ACTIVE-MIB

Object and Object Identifier

Type

Value Range

Description

rbnSubsMaxSupportedSessionsrbnSubsLicense 11.3.6.1.4.1.2352.2.27.1.2.5.1

Gauge32

 

The maximum number of active subscriber sessions on the SmartEdge router.

rbnSubsLicensedSessionsrbnSubsLicense 21.3.6.1.4.1.2352.2.27.1.2.5.2

Gauge32

 

The number of licensed subscriber sessions on the SmartEdge router.

rbnSubsActiveSessionsrbnSubsLicense 31.3.6.1.4.1.2352.2.27.1.2.5.3

Gauge32

 

The number of active subscriber sessions on the SmartEdge router.

rbnSubsCapacityPercentageUsedrbnSubsLicense 41.3.6.1.4.1.2352.2.27.1.2.5.4

RbnPercentage

 

The percentage of licensed subscriber sessions out of all active sessions in use on the SmartEdge router.

1.34.2   MIB Objects to Clear Subscribers

Table 76 describes the MIB objects that clear subscribers in RBN-SUBSCRIBER-ACTIVE-MIB.

Table 76    Objects that clear subscribers in RBN-SUBSCRIBER-ACTIVE

Object and Object Identifier

Type

Value Range

Description

rbnSubsClearSessionId


rbnSubsClear 2


1.3.6.1.4.1.2352.2.27.1.1.3.2

SnmpAdminString

SIZE (0–32)

Clears the subscriber session identified by this value. In a PPP circuit, the PPP state machinery attempts to renegotiate and re-authenticate a new session with the remote peer on the circuit. In RFC 1483 and RFC 1490 encapsulated circuits, the circuit is brought down and then back up and an attempt is made to reauthenticate the subscriber bound to the circuit. This object returns a zero-length string when queried. This object is read-write.

1.34.3   Bounce Objects

Table 77 describes the bounce objects in RBN-SUBSCRIBER-ACTIVE-MIB. Bounce objects remove a subscriber session and reauthorize or reset the session. For example, you can use these objects to reauthorize a subscriber during a subscription change. The objects in the table are read-write.

Table 77    Bounce Objects

Object and Object Identifier

Type

Value Range

Description

rbnSubsBounceName


rbnSubsClear 3


1.3.6.1.4.1.2352.2.27.1.1.3.3

SnmpAdminString

SIZE (0–80)

Each circuit using CLIPS encapsulation used by the named subscriber is brought down and immediately re-created using the RADIUS Access Accept attributes. Any other circuit encapsulation type is cleared. This object returns a zero-length string when queried.

rbnSubsBounceSessionId


rbnSubsClear 4


1.3.6.1.4.1.2352.2.27.1.1.3.4

SnmpAdminString

SIZE (0–32)

The circuit using CLIPS encapsulation identified by the RADIUS Acct-Session-Id is brought down and immediately re-created using the RADIUS Access-Accept attributes. Any other circuit encapsulation type is cleared. This object returns a zero-length string when queried.

1.34.4   Reauthorization Objects

Table 78 describes the reauthorization objects in RBN-SUBSCRIBER-ACTIVE-MIB. All objects in the table are read-write.

Table 78    Reauthorization Objects

Object and Object Identifier

Type

Value Range

Description

rbnSubsReauthName


rbnSubsClear 7


1.3.6.1.4.1.2352.2.27.1.1.3.7

SnmpAdminString

SIZE (0–80)

Reauthorize all of the active sessions associated with the given subscriber in the context identified in the SNMP protocol (the community string in SNMPv1 or SNMPv2 or the contextName in SNMPv3). This object returns a zero-length string when queried.

rbnSubsReauthSessionId


rbnSubsClear 8


1.3.6.1.4.1.2352.2.27.1.1.3.8

SnmpAdminString

SIZE (0–32)

Reauthorize the active session identified by the value of this object and the context identified in the SNMP protocol (the community string in SNMPv1 or SNMPv2 or the contextName object in SNMPv3). This object returns a zero-length string when queried.

rbnSubsClearReason


rbnSubsClear 9


1.3.6.1.4.1.2352.2.27.1.1.3.9

Unsigned32

N/A

An unsigned integer value that may be included in the set request for the rbnSubsClearSubscriberName object, rbnSubsClearSessionId object, rbnSubsBounceName object, rbnSubsBounceSessionId object, or any other objects defines under the rbnSubsClear OID node. The use of this object value is implementation dependent. This object returns 0 when queried.

1.34.5   Notification Objects

Table 79 describes the notification objects in RBN-SUBSCRIBER-ACTIVE-MIB.

Table 79    Notification Objects

Object and Object Identifier

Type

Value Range

Description

rbnSubsNotifyEnable


rbnSubsNotify 1


1.3.6.1.4.1.2352.2.27.1.3.1

TruthValue

1—true


2—false

Provides a mechanism for enabling and disabling subscriber notifications. A value of 1 (true) indicates that subscriber notifications are enabled. A value of 2 (false) indicates that subscriber notifications are disabled. This object is read-write.

1.34.6   rbnSubsActiveTable

This table contains subscriber sessions that have been authenticated on an circuit.

Index: rbnSubsActiveName, rbnSubsActiveSessionId

Table 80 describes the attributes in rbnSubsActiveTable. All objects in the table are read-only.

Table 80    Objects in rbnSubsActiveTable

Object and Object Identifier

Type

Value Range

Description

rbnSubsActiveCircuitDescr


rbnSubsActiveEntry 3


1.3.6.1.4.1.2352.2.27.1.1.1.1.3

SnmpAdminString

SIZE (1–64)

A string that provides identifying information (such as slot or port) of the circuit the subscriber is using.

rbnSubsActiveCircuitHandle


rbnSubsActiveEntry 4


1.3.6.1.4.1.2352.2.27.1.1.1.1.4

RbnCircuitHandleOctet String

SIZE (8)

A value for identifying circuits.

rbnSubsActiveStartTime


rbnSubsActiveEntry 5


1.3.6.1.4.1.2352.2.27.1.1.1.1.5

DateAndTime

N/A

The time when the subscriber became active.

rbnSubsActiveClear


rbnSubsActiveEntry 6


1.3.6.1.4.1.2352.2.27.1.1.1.1.6

TruthValue

1—true


2—false

Setting this value to 'true' clears the active subscriber session. In a PPP, the PPP state machinery attempts to renegotiate and reauthenticate a new session with the remote peer on the circuit. In RFC 1483 encapsulated circuits, the session is brought down and then back up and an attempt is made to reauthenticate the subscriber. An SNMP get operation always returns the value 'false'.

rbnSubsActiveResend


rbnSubsActiveEntry 7


1.3.6.1.4.1.2352.2.27.1.1.1.1.7

TruthValue

1—true


2—false

Setting this value to 'true' causes a resend of the RADIUS acct-start packet. An SNMP get operation always returns 'false'.

rbnSubsActiveNasPortType


rbnSubsActiveEntry 8


1.3.6.1.4.1.2352.2.27.1.1.1.1.8

Unsigned32

N/A

The RADIUS attribute NAS-Port-Type that indicates the type of physical port that is authenticating the user.

rbnSubsActiveMediumType


rbnSubsActiveEntry 9


1.3.6.1.4.1.2352.2.27.1.1.1.1.9

RbnPortMediumType


Integer

0—unknown


11—dsl


12—cable


13—wireless


14—satellite

The medium type of the NAS-Port.

1.34.7   rbnSubsActiveIpTable

This table contains IP addresses used by active subscribers.

Index: rbnSubsActiveName, rbnSubsActiveSessionId, rbnSubsActiveAddrType, rbnSubsActiveAddr

Table 81 describes the attributes in rbnSubsActiveIpTable. All objects in the table are read-only.

Table 81    Objects in rbnSubsActiveIpTable

Object and Object Identifier

Type

Value Range

Description

rbnSubsActiveAddr


rbnSubsActiveIpEntry 2


1.3.6.1.4.1.2352.2.27.1.1.2.1.2

InetAddress


String

SIZE (4 | 16 | 20)

The host IP address of the active subscriber.

1.34.8   rbnSubsCntxtCountTable

This table contains counts of active subscribers by context name. Unlike any of the other tables in this MIB module, all rows in this table are accessible when the local context is specified in the SNMP message, unless restricted by entries in vacmAccessTable. SNMP requests that use other contexts return only the row that matches the context.

Index: vacmContextName

Table 82 describes the attributes in rbnSubsCntxtCountTable. All objects in the table are read-only.

Table 82    Objects in rbnSubsCntxtCountTable

Object and Object Identifier

Type

Value Range

Description

rbnSubsCntxtCount


rbnSubsCntxtCountEntry 1


1.3.6.1.4.1.2352.2.27.1.2.1.1.1

Gauge32

 

The count of active subscribers for the context.

1.34.9   rbnSubsEncapsCountTable

This table contains counts of active subscribers by encapsulation type.

Index: rbnSubsEncapsulationType

Table 83 describes the attributes in rbnSubsEncapsCountTable. All objects in the table are read-only.

Table 83    Objects in rbnSubsEncapsCountTable

Object and Object Identifier

Type

Value Range

Description

rbnSubsEncapsCount


rbnSubsEncapsCountEntry 2


1.3.6.1.4.1.2352.2.27.1.2.2.1.2

Gauge32

N/A

The count of active subscribers for the encapsulation type.

1.34.10   rbnSubsStatsTable

This table contains counters for individual circuits.

Index: rbnSubsActiveName, rbnSubsActiveSessionId

Table 84 describes the attributes in rbnSubsStatsTable. All objects in the table are read-only.

Table 84    Objects in rbnSubsStatsTable

Object and Object Identifier

Type

Value Range

Description

rbnSubsOctetsSent


rbnSubsStatsEntry 1


1.3.6.1.4.1.2352.2.27.1.2.3.1.1

Counter64

N/A

The number of octets sent by the circuit. This counter includes multicast activity.

rbnSubsOctetsReceived


rbnSubsStatsEntry 2


1.3.6.1.4.1.2352.2.27.1.2.3.1.2

Counter64

N/A

The number of octets received by the circuit. This counter includes multicast activity.

rbnSubsPktsSent


rbnSubsStatsEntry 3


1.3.6.1.4.1.2352.2.27.1.2.3.1.3

Counter64

N/A

The number of packets sent by the circuit. This counter includes multicast activity.

rbnSubsPktsReceived


rbnSubsStatsEntry 4


1.3.6.1.4.1.2352.2.27.1.2.3.1.4

Counter64

N/A

The number of packets received by the circuit. This counter includes multicast activity.

rbnSubsXmitOctetsDropped


rbnSubsStatsEntry 5


1.3.6.1.4.1.2352.2.27.1.2.3.1.5

Counter32

N/A

The number of octets dropped by the circuit before transmission.

rbnSubsXmitPktsDropped


rbnSubsStatsEntry 6


1.3.6.1.4.1.2352.2.27.1.2.3.1.6

Counter32

N/A

The number of packets dropped by the circuit before transmission.

rbnSubsMcastOctetsSent


rbnSubsStatsEntry 7


1.3.6.1.4.1.2352.2.27.1.2.3.1.7

Counter64

N/A

The number of multicast octets sent by the circuit.

rbnSubsMcastOctetsReceived


rbnSubsStatsEntry 8


1.3.6.1.4.1.2352.2.27.1.2.3.1.8

Counter64

N/A

The number of multicast octets received by the circuit.

rbnSubsMcastPktsSent


rbnSubsStatsEntry 9


1.3.6.1.4.1.2352.2.27.1.2.3.1.9

Counter64

N/A

The number of multicast packets sent by the circuit.

rbnSubsMcastPktsReceived


rbnSubsStatsEntry 10


1.3.6.1.4.1.2352.2.27.1.2.3.1.10

Counter64

N/A

The number of multicast packets received by the circuit.

1.34.11   rbnSubsProfileCountTable

This table contains counts of active subscribers by encapsulation type.

Index: IMPLIED rbnSubsProfileName

Table 85 describes the attributes in rbnSubsProfileCountTable. All objects in the table are read-only.

Table 85    Objects in rbnSubsProfileCountTable

Object and Object Identifier

Type

Value Range

Description

rbnSubsProfileCount


rbnSubsProfileCountEntry 2


1.3.6.1.4.1.2352.2.27.1.2.4.1.2

Gauge32

N/A

The count of active subscribers for the profile name.

1.34.12   rbnSubsServiceVolumeTable

This table specifies service volume information on the subscriber circuits. It contains the volume octet counts for each active subscriber session for which the service is active.

All MIB objects defined in the table are viewed within the context identified in the SNMP protocol (the community string in SNMPv1 or SNMPv2, or the contextName in SNMPv3.)

Index: rbnSubsActiveName, rbnSubsActiveSessionId, rbnSubsServiceIndex

Table 86 describes the attributes in rbnSubsServiceVolumeTable. All objects in the table are read-only.

Table 86    Objects in rbnSubsServiceVolumeTable

Object and Object Identifier

Type

Value Range

Description

rbnSubsServiceVolumeLimitIn


rbnSubsServiceVolumeEntry 1


1.3.6.1.4.1.2352.2.27.1.1.4.1.1

Unsigned32

N/A

The volume limit in kilobytes (KB) allowed for the subscriber service to input (or receive) for this subscriber. If the value is 0, then there is no limit.

rbnSubsServiceVolumeLimitOut


rbnSubsServiceVolumeEntry 2


1.3.6.1.4.1.2352.2.27.1.1.4.1.2

Unsigned32

N/A

The volume limit in kilobytes (KB) allowed for the subscriber service to output (or transmit) for this subscriber. If the value is 0, then there is no limit.

rbnSubsServiceActiveTime


rbnSubsServiceVolumeEntry 3


1.3.6.1.4.1.2352.2.27.1.1.4.1.3

TimeStamp

N/A

The value of sysUpTime when the service became active for this subscriber. If sysUpTime is reset to zero as a result of a reinitialization of the network management system or subsystem, the values of all TimeStamp objects are also reset.

rbnSubsServiceVolumeOctetsIn


rbnSubsServiceVolumeEntry 4


1.3.6.1.4.1.2352.2.27.1.1.4.1.4

Counter64

N/A

The subscriber session volume octets in count.

rbnSubsServiceVolumeOctetsOut


rbnSubsServiceVolumeEntry 5


1.3.6.1.4.1.2352.2.27.1.1.4.1.5

Counter64

N/A

The subscriber session volume octets out count.

rbnSubsServiceVolumePktsIn


rbnSubsServiceVolumeEntry 6


1.3.6.1.4.1.2352.2.27.1.1.4.1.6

Counter64

N/A

The subscriber session volume packet in count.

rbnSubsServiceVolumePktsOut


rbnSubsServiceVolumeEntry 7


1.3.6.1.4.1.2352.2.27.1.1.4.1.7

Counter64

N/A

The subscriber session volume packet out count.

1.34.13   rbnSubsServicesTable

This table contains services available to subscribers. To perform a MIB walk for this table, you must first perform a MIB walk of the rbnSubsServiceVolumeTable.

Index: rbnSubsServiceIndex

Table 87 describes the attributes in rbnSubsServicesTable. All objects in the table are read-only.

Table 87    Objects in rbnSubsServicesTable

Object and Object Identifier

Type

Value Range

Description

rbnSubsServiceName


rbnSubsServicesEntry 2


1.3.6.1.4.1.2352.2.27.1.1.5.1.2

SnmpAdminString

SIZE (1–128)

The name identifying the service.

rbnSubsServiceTag


rbnSubsServicesEntry 3


1.3.6.1.4.1.2352.2.27.1.1.5.1.3

SnmpAdminString

SIZE (0–32)

A tag associated with the service name, which may provide additional qualification to the name.

1.34.14   Example: How to Obtain the Circuit Description of an Active Subscriber

You can use the RBN-SUBSCRIBER-ACTIVE-MIB to interpret the index number of a subscriber to ASCII string. To query the circuit description value of an active subscriber named, client-v10@test1, you can run the following SNMP query:

getnext -v2c qcup.lab public@ctx1

rbnSubsActiveCircuitDescr.16.99.108.105.101.110.116.45.118.49.48.64.116.
101.115.116.49

getone -v2c qcup.lab public@ctx1

rbnSubsActiveCircuitDescr.16.99.108.105.101.110.116.45.118.49.48.64.
116.101.115.116.49.25.70.70.49.48.70.70.70.70.53.56.65.49.69.69.49.
53.45.52.52.50.66.51.52.51.65

The value of rbnsubsActiveCircuitDescr contains the information about the subscriber name length, subscriber name, and session ID. The OID returns values in this way: rbnSubsActiveCircuitDescr.[subscriber name length].[subscriber name].[session id length].[session id]. The value of rbnsubsActiveCircuitDescr is L2TP LNS 10612245. Broken down, this means that the length of subscriber name is 16 (decimal). The subscriber name is 99.108.105.101.110.116.45.118.49.48.64.116.101.115.116.49 or, in text form, client-v10@test1, and the session ID has a length of 25 with a value 25.70.70.49.48.70.70.70.70.53.56.65.49.69.69.49.53.45.52.52.50.66.51.52.51.65 or, in text form, FF10FFFF58A1EE15-442B343A.

Use the subscriber name in the rbnSubscriberActiveMib object to display the information in the CLI and show the SNMP information about the subscriber. In this example, the CLI displays this output:

[local]#show sub all

TYPE   CIRCUIT          SUBSCRIBER   CONTEXT    START TIME
----------------------------------------------------------------------

ppp L2TP LNS 10612245 client-v10@test1 ctx1 Mar 29 18:28:26

ppp L2TP LNS 10612246 client-v11@test1 ctx1 Mar 29 18:28:26

ppp L2TP LNS 10612247 client-v12@test1 ctx1 Mar 29 18:28:27

ppp L2TP LNS 10612248 client-v13@test1 ctx1 Mar 29 18:28:27

ppp L2TP LNS 10612249 client-v14@test1 ctx1 Mar 29 18:28:27

ppp L2TP LNS 10612250 client-v15@test2 ctx2 Mar 29 18:28:27

ppp L2TP LNS 10612251 client-v16@test2 ctx2 Mar 29 18:28:27

ppp L2TP LNS 10612252 client-v17@test2 ctx2 Mar 29 18:28:27

ppp L2TP LNS 10612253 client-v18@test2 ctx2 Mar 29 18:28:27

ppp L2TP LNS 10612254 client-v19@test2 ctx2 Mar 29 18:28:27

---------------------------------------------------------------------

Total=10

1.35   RBN-SYS-RESOURCES-MIB

Manages system resources, such as process events, disk utilization, and switchovers.

When using this MIB, there are differences in the usage of memory and CPU usage. This MIB can also help to generate a SNMP trap.

The following sections describes object information for RBN-SYS-RESOURCES-MIB.

1.35.1   Notification Objects

Table 88 describes the notification objects for RBN-SYS-RESOURCES-MIB. All objects in the table are read-only unless otherwise specified.

Table 88    Notification Objects

Object and Object Identifier

Type

Value Range

Description

rbnSRProcessNotifyLastUpdate


rbnSRProcess 1


1.3.6.1.4.1.2352.2.24.1.1.1

TimeTicks


Integer

0– 4294967295

The value of sysUpTime when an entry in rbnSRProcessNotifyTable was last added. Because this table can contain many entries, polling of this object allows a management station to determine when redownloading of the table might be useful.

rbnSRProcessEventNotifyEnable


rbnSRProcess 2


1.3.6.1.4.1.2352.2.24.1.1.2

Integer

1—enabled


2—disabled

Indicates whether the rbnSRProcessEvent notification should be generated for this system. This object is read-write.

1.35.2   System Group Objects

Table 89 describes the attributes in system group objects. All objects in the table are read-only unless otherwise specified.

Table 89    System Group Objects

Object and Object Identifier

Type

Value Range

Description

rbnSRSystemUptime


rbnSRSystem 1


1.3.6.1.4.1.2352.2.24.1.3.1

TimeTicks


Integer

0– 4294967295

The amount of time since this system was last initialized. Note that this is different from sysUpTime in the SNMPv2-MIB [RFC1907] because sysUpTime is the uptime of the network management portion of the system.

rbnSRSystemDate


rbnSRSystem 2


1.3.6.1.4.1.2352.2.24.1.3.2

DateAndTime

N/A

The local date and time of day on the host.

rbnSRPowerExceededStatus


rbnPowerExceeded 1


1.3.6.1.4.1.2352.2.24.1.4.1

Integer

1—normal


2—failed

The status of alarm when a controller card is inserted and results in more power being drawn than recommended. If an instance of this object has the value normal, then the chassis power has not been exceeded. If an instance of this object has the value failed, the chassis power was exceeded when a controller card was inserted. This object is accessible-for-notify.

1.35.3   rbnSRProcessNotifyTable

A list of process event notifications since the agent was last reinitialized. If no process event has ever been generated, this table is empty, for example, has zero entries.

Index: rbnSRProcessNotifyProcName

Table 90 describes the attributes in rbnSRProcessNotifyTable. All objects in the table are read-only.

Table 90    Objects in rbnSRProcessNotifyTable

Object and Object Identifier

Type

Value Range

Description

rbnSRProcessNotifyPID


rbnSRProcessNotifyEntry 2


1.3.6.1.4.1.2352.2.24.1.1.3.1.2

Unsigned32

0– 214748364

A decimal number uniquely identifies the process. The value 0 indicates the process has not been started.

rbnSRProcessNotifyEventCause


rbnSRProcessNotifyEntry 3


1.3.6.1.4.1.2352.2.24.1.1.3.1.3

Integer

1—firstStart


2—hangup


3—interrupt


4—quit


5—illegalInstruction


6—traceTrap


7—abort


8—emt


9—floatingPointException


10—kill


11—busError


12—segmentFault


13—systemCallError


14—pipeError


15—alarmClock


16—softwareTermination


17—urgentConditionOnIOChannel


18—stopNotFromTty


19—stopFromTty


20—continueStopped


21—childExit


22—ttyInput


23—ttyOutput


24—inputOutput


25—exceededCpuTime


26—exceededFileSize


27—virtualAlarm


28—profilingAlarm


29—windowResize


30—infoRequest


31—userDefined1


32—userDefined2


33—powerFailRestart


34—unknown

Identifies the cause of a process death or birth event. The value firstStart (1) indicates that the process has been started the first time. The other values identify the process exit status recorded on the last process death event. On the SmartEdge platform, these values correspond 1-to-1 with the values displayed by the 'show process crash-info' CLI command.

rbnSRProcessNotifyEventType


rbnSRProcessNotifyEntry 4


1.3.6.1.4.1.2352.2.24.1.1.3.1.4

Integer

1—death


2—birth

The type of event notification sent on the process described by this row of the table. The process event type death (1) indicates that the agent has been informed that the process is not available for any use. The event type birth (2) indicates that the agent has been informed that the process has started.

rbnSRProcessNumOfSpawn


rbnSRProcessNotifyEntry 5


1.3.6.1.4.1.2352.2.24.1.1.3.1.5

Unsigned32

0–2147483647

The number of times the process has been spawned since the system was last initialized. Note that this is different from the restart of the network management portion of the system.

rbnSRProcessNotifyLastTimeSent


rbnSRProcessNotifyEntry 6


1.3.6.1.4.1.2352.2.24.1.1.3.1.6

TimeTicks


Integer

0– 4294967295

The value of the sysUpTime object at the time this notification was last generated on the process.

1.35.4   rbnSRStorageTable

This is a table of long-term storage devices contained by the system. Disk devices accessed remotely over a network are not included.

Index: rbnSRStorageIndex

Table 91 describes the attributes in rbnSRStorageTable. All objects in the table are read-only unless otherwise specified.

Table 91    Objects in rbnSRStorageTable

Object and Object Identifier

Type

Value Range

Description

rbnSRStorageDescr


rbnSRStorageEntry 2


1.3.6.1.4.1.2352.2.24.1.2.1.1.2

SnmpAdminString

SIZE (0–64)

A textual description of this storage device, optionally including the device manufacturer, revision, and serial number.

rbnSRStorageMedia


rbnSRStorageEntry 3


1.3.6.1.4.1.2352.2.24.1.2.1.1.3

Integer

1—other


2—hardDisk


3—flashMemory

The type of media used in this long-term storage device.

rbnSRStorageRemovable


rbnSRStorageEntry 4


1.3.6.1.4.1.2352.2.24.1.2.1.1.4

TruthValue

1—true


2—false

Denotes whether or not the storage media can be removed from the slot.

rbnSRStorageSize


rbnSRStorageEntry 5


1.3.6.1.4.1.2352.2.24.1.2.1.1.5

RbnKBytes


Integer32

0–2147483647

The total size for this long-term storage device. If the media is removeable and is currently removed, this value should be zero.

rbnSRStorageUtilization


rbnSRStorageEntry 6


1.3.6.1.4.1.2352.2.24.1.2.1.1.6

RbnPercentage


Integer32

0–100

The percent utilization of the storage space on a scale of 0 to 100 percent. The formula used to calculate the Utilization is as follows. used blocks * 100 Utilization = free blocks avail to the user + used blocks Note that the divisor is the total number of blocks available to the user, which is a subset of the total storage size on the device in the rbnSRStorageSize object.

rbnSRStorageSlot


rbnSRStorageEntry 7


1.3.6.1.4.1.2352.2.24.1.2.1.1.7

RbnSlot


Unsigned32

(0–255)

The chassis slot number in which the controller card containing this storage device is present.

rbnSRStorageMountTime


rbnSRStorageEntry 8


1.3.6.1.4.1.2352.2.24.1.2.1.1.8

TimeTicks


Integer

0– 4294967295

The value of sysUpTime when this storage device was last mounted.

rbnSRStorageStatus


rbnSRStorageEntry 9


1.3.6.1.4.1.2352.2.24.1.2.1.1.9

Integer

1—operational


2—degrading


3—failed

The functional status of this storage device.

rbnSRStorageErrors


rbnSRStorageEntry 10


1.3.6.1.4.1.2352.2.24.1.2.1.1.10

Counter32

N/A

The cumulative count of soft errors on this storage device.

1.36   RBN-TACACS-MIB

Defines notifications for tracking the Terminal Access Controller Access Control System Plus (TACACS+) server state (in accordance with Internet-Draft draft-grant-tacacs-02.txt).

1.36.1   TACACS+ Notification Objects

Table 92 describes the notification objects for RBN-TACACS-MIB. All objects in the table are read-only unless otherwise specified.

Table 92    TACACS+ Notification Objects

Object and Object Identifier

Type

Value Range

Description

rbnTacacsContext


rbnTacacsNotifyObjects 1


1.3.6.1.4.1.2352.2.33.1.3.1

SnmpAdminString

SIZE (1–63)

The name of the context in which this server is configured. This object is accessible-for-notify.

rbnTacacsServerIndex


rbnTacacsNotifyObjects 2


1.3.6.1.4.1.2352.2.33.1.3.2

Unsigned32

1– 4294967295

A unique index value assigned to each TACACS server. This object is accessible-for-notify.

rbnTacacsServerAddressType


rbnTacacsNotifyObjects 3


1.3.6.1.4.1.2352.2.33.1.3.3

InetAddressType


Integer

0—unknown


1—ipv4


2—ipv6


16—dns

The type of address contained in the rbnTacacsServerAddress object. This object is accessible-for-notify.

rbnTacacsServerAddress


rbnTacacsNotifyObjects 4


1.3.6.1.4.1.2352.2.33.1.3.4

InetAddress


String

SIZE (0–255)

The TACACS+ server address. This object is accessible-for-notify.

rbnTacacsServerPort


rbnTacacsNotifyObjects 5


1.3.6.1.4.1.2352.2.33.1.3.5

Unsigned32

0–65535

The TCP port number. This object is accessible-for-notify.

rbnTacacsServerState


rbnTacacsNotifyObjects 6


1.3.6.1.4.1.2352.2.33.1.3.6

RbnTacacsState


Integer

1—unknown


2—up


3—down

The current state of the TACACS+ server. This object is accessible-for-notify.

rbnTacacsServerReason


rbnTacacsNotifyObjects 7


1.3.6.1.4.1.2352.2.33.1.3.7

RbnTacacsReason


Integer

1—responding


2—packetTimeout


3—serverTimeout


4—serverError

The reason for the server's last state change. This object is accessible-for-notify.

rbnTacacsUserName


rbnTacacsNotifyObjects 8


1.3.6.1.4.1.2352.2.33.1.3.8

SnmpAdminString

SIZE (0–128)

The name of the user the system was trying to authenticate or send accounting information for when the TACACS+ server transitioned to 'down'. The 'username' is valid only when transitioning due to a packet-level timeout. When transitioning due to any other reason, the value for this object will be a zero-length string. This object is accessible-for-notify.

rbnTacacsServerMsg


rbnTacacsNotifyObjects 9


1.3.6.1.4.1.2352.2.33.1.3.9

SnmpAdminString

SIZE (0–256)

A text string optionally provided by the TACACS+ server when the rbnTacacsServerReason object is 'serverError'. In all other cases, this is a zero-length string. This object is accessible-for-notify.