Configuring Cards

Contents

1Overview
1.1Card Types
1.2SmartEdge 100 Router Considerations
1.3Related Information

2

Configuration and Operations Tasks
2.1Configure a SmartEdge 100 MIC
2.2Configure a SmartEdge 400, 800, 600, 1200, or 1200H Card
2.3Line Card Operations

3

Configuration Examples
3.1POS OC-12c/STM-4c Line Card (4-Port)
3.2ATM OC-3c/STM-1c Line Card (4-Port)
3.3ATM OC-3c/STM-1c Line Card (8-Port)
3.4ATM DS-3 Line Card (12-Port)
3.5FE-GE Line Card (2-Port)

Reference List
Copyright

© Ericsson AB 2009–2010. All rights reserved. No part of this document may be reproduced in any form without the written permission of the copyright owner.

Disclaimer

The contents of this document are subject to revision without notice due to continued progress in methodology, design and manufacturing. Ericsson shall have no liability for any error or damage of any kind resulting from the use of this document.

Trademark List
SmartEdge is a registered trademark of Telefonaktiebolaget LM Ericsson.
NetOp is a trademark of Telefonaktiebolaget LM Ericsson.

1   Overview

Line cards and MICs are the individual I/O cards in a SmartEdge chassis. A SmartEdge chassis supports many different types of line cards, and configuration and operations tasks for each card can vary.

The procedures described in this document are common to all card types, except where noted.

This document describes how to configure all types of SmartEdge line cards and services cards in the SmartEdge 100, 400, 600, 800, 1200, and 1200H chassis and provides information about the capabilities of these cards. This document also describes setting up and using the SmartEdge 100 media interface cards (MICs) and native ports.

1.1   Card Types

Table 1 lists SmartEdge 100 controller card and the MICs that are supported on the SmartEdge 100 router. In addition to these MICs, the SmartEdge 100 also includes two native GE ports that support either 1000Base-T or 1000Base-FX.

Table 1    SmartEdge 100 Card Types

Type of Card

Full Name of Card

CLI Name of Card

MIC

 

10/100Base-TX Ethernet (12-port MIC)

fe-12-port

 

10/100Base-FX Ethernet (12-port MIC)

fe-12-portt

ATM

 

ATM OC-3c/STM-1c (2-port MIC)(1)

atm-oc3-2-port

Ethernet

 

1000Base-T Gigabit Ethernet (2-port)

ge-2-port

 

1000Base-FX Gigabit Ethernet (2-port)

ge-2-port

Controller card

 

SmartEdge100 controller carrier card

xcrp - SE100

(1)  This card is referred to as a PPA2-based line card.


Table 2 lists the SmartEdge cards that are supported on the SmartEdge 400 and SmartEdge 800 routers; in the table, ER, IR, LR, and SR abbreviations are used for Extended Reach, Intermediate Reach, Long Reach, and Short Reach, respectively. Both first generation and second generation ATM OC cards are included in the table.

Table 2    SmartEdge 400 and SmartEdge 800 Cards

Type of Card

Full Name of Card

CLI Name of Card

ATM

 

ATM OC-3c/STM-1c (8-port)

atm-oc3e-8-port

 

ATM OC-3c/STM-1c IR (4-port)

atm-oc3-4-port

 

ATM OC-12c/STM-4c (2-port)

atm-oc12e-2-port

 

Enhanced ATM OC-12c/STM-4c IR (1-port)

atm-oc12e-1-port

 

ATM OC-12c/STM-4c IR (1-port)

atm-oc12-1-port

 

ATM DS-3 (12-port)(1)

atm-ds3-12-port

POS

 

POS OC-3c/STM-1c (8-port)

oc3e-8-port

 

POS OC-12c/STM-4c (4-port)

oc12e-4-port

 

POS OC-48c/STM-16c (4-port)

oc48e-4-port

 

OC-192c/STM-64c (1-port)

oc192-1-port

 

OC-3c/STM-1c IR (8-port)

oc3-8-port

 

OC-12c/STM-4c IR (4-port)

oc12-4-port

 

OC-48c/STM-16c (4-port)

oc48-4-port

 

OC-48c/STM-16c (1-port)

oc48-1-port

Ethernet

 

10/100 Ethernet (12-port)

ether-12-port

 

Fast Ethernet–Gigabit Ethernet (60-port FE, 2-port GE)

fege-60-2-port

 

Gigabit Ethernet (4-port)

ge-4-port

 

Advanced Gigabit Ethernet (4-port)

gigaether-4-port(2)

 

Gigabit Ethernet 3 (4-port)

ge3-4-port

 

Gigabit Ethernet 1020 (10-port)

ge-10-port

 

Gigabit Ethernet 1020 (20-port)

ge-20-port

 

Gigabit Ethernet (5-port)

ge-5-port

 

Gigabit Ethernet DDR (10-port)

ge2-10-port

 

10 Gigabit Ethernet (1-port)

10ge-1-port

 

10 Gigabit Ethernet/OC-192c DDR (1-port)

10ge-oc192-1-port

PDH(3) (Plesiochronous Digital Hierarchy) line card:

 

Channelized DS-3 card (12-port)

ch-ds3-12-port

 

Channelized DS-3 card (3-port)

ch-ds3-3-port

 

Channelized E1 card (24-port)

ch-e1ds0-24-port

 

Clear-channel E3 card (6-port)

e3-6-port


 

Clear-channel DS-3 card (12-port)

ds3-12-port

ASE

 

Advanced Services Engine

ase

Controller card

 

XCRP4 Controller card with software configurable interface to external timing equipment (BITS or SSU) and 8 of GB memory

xcrp4 (base)

(1)  The SmartEdge 800s chassis does not support the ATM DS-3 line card.

(2)  For the second version of the Gigabit Ethernet card, the show hardware command (in any mode) with the detail keyword displays gigaether-4-port-adv as the card type.

(3)  The SmartEdge 800s chassis does not support the DS-3 and E3 line cards.


Table 3 lists the SmartEdge cards that are supported on the SmartEdge 600, 1200, or 1200H router.

Table 3    SmartEdge 600, 1200, or 1200H Cards

Type of Card

Full Name of Card

CLI Name of Card

ATM

 

ATM OC-3c/STM-1c (8-port)

atm-oc3e-8-port

 

ATM OC-3c/STM-1c IR (4-port)

atm-oc3-4-port

 

ATM OC-12c/STM-4c (2-port)

atm-oc12e-2-port

 

Enhanced ATM OC-12c/STM-4c IR (1-port)

atm-oc12e-1-port

POS

 

POS OC-3c/STM-1c (8-port)(1)

oc3e-8-port

 

POS OC-12c/STM-4c (4-port)

oc12e-4-port

 

POS OC-48c/STM-16c (4-port)

oc48e-4-port

 

OC-192c/STM-64c (1-port)

oc192-1-port

Ethernet

 

10/100 Ethernet (12-port)

ether-12-port

 

Fast Ethernet–Gigabit Ethernet (60-port FE, 2-port GE)

fege-60-2-port

 

Gigabit Ethernet (4-port)

ge-4-port

 

Advanced Gigabit Ethernet (4-port)

gigaether-4-port(2)

 

Gigabit Ethernet 3 (4-port)

ge3-4-port

 

Gigabit Ethernet 1020 (10-port)

ge-10-port

 

Gigabit Ethernet 1020 (20-port)

ge-20-port

 

Gigabit Ethernet (5-port)

ge-5-port

 

Gigabit Ethernet (20-port)

ge4-20-port

 

Gigabit Ethernet DDR (10-port)

ge2-10-port

 

10 Gigabit Ethernet (1-port)

10ge-1-port

 

10 Gigabit Ethernet (4-port)

10ge-4-port

 

10 Gigabit Ethernet/OC-192c DDR (1-port)

10ge-oc192-1-port

ASE

 

Advanced Services Engine

ase

SSE

 

SmartEdge Storage Engine

sse

Controller card

 

XCRP4 Controller card with configurable interface to external timing equipment (BITS or SSU) and 8 GB memory

xcrp4 (base)

(1)  Use part number SFP-OC3-SM-IR when ordering the SFP transceivers with POS OC-3 SR-1 or POS OC-3 IR-1 functionality.

(2)  For the second version of the Gigabit Ethernet card, the show hardware command (in any mode) with the detail keyword displays gigaether-4-port-adv as the card type.


1.2   SmartEdge 100 Router Considerations

Line cards and media interface cards (MICs) are the individual I/O cards in a SmartEdge chassis; ports are the physical interfaces on the SmartEdge line cards and MICs, and a channel is a logical subdivision of the bandwidth of a channelized port on a line card. The SmartEdge 400 and SmartEdge 800 routers support many different types of line cards, ports, and channels. The SmartEdge 100 router supports Ethernet and Gigabit Ethernet (GE) ports and MICs:

1.3   Related Information

Other documents with related tasks and commands include:

2   Configuration and Operations Tasks

2.1   Configure a SmartEdge 100 MIC

To configure the basic features for a SmartEdge 100 MIC, perform the tasks described in Table 4; enter all commands in card configuration mode, unless otherwise noted.

Table 4    Configure a SmartEdge 100 MIC

Step

Task

Root Command

Notes

1.

Configure a card and access card configuration mode.

card

Enter this command in global configuration mode; specify the carrier keyword.

2.

Specify the rate and burst limits rate for Point-to-Point Protocol (PPP) over Ethernet over ATM (PPPoEoA) Active Discovery Initiation (PADI) packets and PPP over ATMe (PPPoA) Configure-Request packets that arrive at the SmartEdge router on circuit creation on demand (CCOD) ATM permanent virtual circuits (PVCs).

rate-limit ccod

 

3.

Specify the rate and burst limits for Point-to-Point Protocol over Ethernet (PPPoE) Active Discovery Initiation (PADI) packets that arrive at the SmartEdge router.

rate-limit padi

 

4.

Specify the rate and burst limits for PPP Link Control Protocol (LCP) Configure-Request packets that arrive at the SmartEdge router on static ATM PVCs.

rate-limit ppp-lcp-confreq

 

5.

Specify the MIC type for the specified slot before the MIC is inserted in the SmartEdge 100 router, and access MIC configuration mode.

mic

 

6.

Specify the mode for the segmentation and reassembly (SAR) image in the ATM MIC.

atm mode

Enter this command in MIC configuration mode. This command applies to ATM OC MICs only.

2.2   Configure a SmartEdge 400, 800, 600, 1200, or 1200H Card

To configure the basic features for an SmartEdge line card, perform the tasks described in Table 5; enter all commands in card configuration mode, unless otherwise noted.

Table 5    Configure a Line Card

Step

Task

Root Command

Notes

1.

Configure a card and access card configuration mode.

card

Enter this command in global configuration mode.

2.

Specify the number of configurable ports.

maximum ports

 

3.

Specify card-specific attributes. (All attributes are optional.)

 

Enable SONET path maintenance, path trace, and path alarm monitoring features for the card.

sonet-eu

This command applies to first-generation ATM OC and all POS line cards only.

 

Select the clock source for the card.

clock-source (ATM card)

This command applies to ATM DS-3 and second-generation ATM OC line cards only.

 

Specify the mode for the segmentation and reassembly (SAR) image in the card.

atm mode

This command applies to ATM DS-3 and second-generation ATM OC line cards and MICs only.

 

Enable lossless flow control for jumbo frames.

lossless-large-mtu

This command applies to the FE-GE line card only.

 

Specify the port speed and duplex mode for all FE ports.

medium (fast-ethernet)

This command applies to the FE-GE line card only.

 

Specify the MTU size of the payload without fragmentation for all FE ports.

mtu (card)

This command applies to the FE-GE line card only.

4.

Increase the maximum number of circuits on the 1-port 10 Gigabit Ethernet card (10ge-1-port) to 32,000.

high-circuit-count

This command applies to the 10ge-1-port line card only.

5.

Specify the rate and burst limits for PPPoEoA PADI packets and PPPoA Configure-Request packets that arrive at the SmartEdge Router on CCOD ATM PVCs.

rate-limit ccod

 

6.

Specify the rate and burst limits for PPPoE PADI packets that arrive at the SmartEdge Router.

rate-limit padi

 

7.

Specify the rate and burst limits for PPP LCP Configure-Request packets that arrive at the SmartEdge router on static ATM PVCs.

rate-limit ppp-lcp-confreq

 

2.2.1   Configure an ASE Card

For information about how to configure an ASE card, see Reference [4].

2.2.2   Configure an SSE Card

For information about how to configure an SSE card, see Reference [5].

2.3   Line Card Operations

To display the chassis slot number for the destination line card, perform the task listed in Table 6. Enter the show command in any mode.

Table 6    Line Card Operations Tasks

Task

Root Command

Display the chassis slot number for the destination line card.

show destination card

Shows slots in which cards are installed and their state.

show chassis

3   Configuration Examples

3.1   POS OC-12c/STM-4c Line Card (4-Port)

The following example shows how to configure a POS OC-12c/STM-4c line card in slot 3 and enable SONET path and alarm monitoring:

[local]Redback(config)#card oc12-4-port 3
[local]Redback(config-card)#sonet-eu
[local]Redback(config-card)#exit

3.2   ATM OC-3c/STM-1c Line Card (4-Port)

The following example shows how to configure a 4-port ATM OC-3c/STM-1c line card in slot 4 and specify ATM priority mode for the line card:

[local]Redback(config)#card atm-oc3-4-port 4
[local]Redback(config-card)#atm mode atm-priority
Note: enable atm-priority SAR image will cause card reload
commit to continue; abort to exit without change
[local]Redback(config-card)#exit

3.3   ATM OC-3c/STM-1c Line Card (8-Port)

The following example shows how to configure a 8-port ATM OC-3c/STM-1c line card in slot 2 and specify vc-fair mode for the line card using the default method:

[local]Redback(config)#card atm-oc3-8-port 2
Enter configuration commands, one per line, 'end' to exit

The following example shows how to configure a 8-port ATM OC-3c/STM-1c line card in slot 2 and specify vc-fair mode for the line card:

[local]Redback(config)#card atm-oc3-8-port 2
[local]Redback(config-card)#atm mode vc-fair
Note: enable vc-fair SAR image will cause card reload 
commit to continue; abort to exit without change
[local]Redback(config-card)#commit

The following example shows how to configure a 8-port ATM OC-3c/STM-1c line card in slot 2 and specify hsvc-fair mode for the line card:

[local]Redback(config)#card atm-oc3-8-port 2
[local]Redback(config-card)#atm mode hsvc-fair
Note: enable hsvc-fair SAR image will cause card reload 
commit to continue; abort to exit without change
[local]Redback(config-card)#commit

3.4   ATM DS-3 Line Card (12-Port)

The following example shows how to specify the first 8 ports on an ATM DS-3 line card in slot 5 as software configurable:

[local]Redback(config)#card atm-ds3 5
[local]Redback(config-card)#maximum ports 8
[local]Redback(config-card)#exit

3.5   FE-GE Line Card (2-Port)

The following example shows how to specify lossless flow control for the 1 and 2 port groups, a speed of 100 Mbps in full-duplex mode, and an MTU of 9600 for all ports on the FE-GE line card in slot 4:

[local]Redback(config)#card fege-60-2-port 4
[local]Redback(config-card)#lossless-large-mtu port-group 1 2
[local]Redback(config-card)#medium 100 duplex full
[local]Redback(config-card)#mtu 9600
[local]Redback(config-card)#exit

Reference List

[1] Configuring Circuits, 12/1543-CRA 119 1170/1
[2] Configuring ATM, Ethernet, and POS Ports, 9/1543-CRA 119 1170/1
[3] Configuring Channels and Clear-Channel and Channelized Ports, 11/1543-CRA 119 1170/1
[4] Advanced Services Configuration and Operation Using the SmartEdge OS CLI, 1/1543-CRA 119 1170/1
[5] SSE Configuration and Operation, 86/1543-CRA 119 1170/1
[6] Command List, 1/190 77-CRA 119 1170/1