Commands: show n through show o

Contents

1Command Descriptions
1.1show nat policy
1.2show nat pool
1.3show nd circuit
1.4show nd interface
1.5show nd neighbor
1.6show nd prefix
1.7show nd profile
1.8show nd static-neighbor
1.9show nd statistics
1.10show nd summary
1.11show netop
1.12show ntp associations
1.13show ntp status
1.14show ospf
1.15show ospf3
1.16show ospf3 area
1.17show ospf3 asbr
1.18show ospf3 database
1.19show ospf3 database advertising router
1.20show ospf3 database grace
1.21show ospf3 database inter-prefix
1.22show ospf3 database inter-router
1.23show ospf3 database intra-prefix
1.24show ospf3 database link
1.25show ospf3 database network
1.26show ospf3 database nssa
1.27show ospf3 database router
1.28show ospf3 debug
1.29show ospf3 interface
1.30show ospf3 intra-rib
1.31show ospf3 malform
1.32show ospf3 neighbor
1.33show ospf3 route
1.34show ospf3 spf
1.35show ospf3 statistics
1.36show ospf3 summary-address
1.37show ospf area
1.38show ospf border-routers
1.39show ospf database
1.40show ospf database advertising router
1.41show ospf database area-scope-opaque
1.42show ospf database as-scope-opaque
1.43show ospf database database-summary
1.44show ospf database external
1.45show ospf database interface
1.46show ospf database link-scope-opaque
1.47show ospf database network
1.48show ospf database nssa
1.49show ospf database router
1.50show ospf database summary-asbr
1.51show ospf database summary-network
1.52show ospf debug
1.53show ospf interface
1.54show ospf neighbor
1.55show ospf route
1.56show ospf route vpn
1.57show ospf spf
1.58show ospf statistics
1.59show ospf summary-address
1.60show ospf vpn
Copyright

© Ericsson AB 2009–2010. All rights reserved. No part of this document may be reproduced in any form without the written permission of the copyright owner.

Disclaimer

The contents of this document are subject to revision without notice due to continued progress in methodology, design and manufacturing. Ericsson shall have no liability for any error or damage of any kind resulting from the use of this document.

Trademark List
SmartEdge is a registered trademark of Telefonaktiebolaget LM Ericsson.
NetOp is a trademark of Telefonaktiebolaget LM Ericsson.

1   Command Descriptions

Commands starting with “show n” through commands starting with “show o” are included.

1.1   show nat policy

show nat policy [pol-name [detail]]

1.1.1   Purpose

Displays information for configured Network Address Translation (NAT) policies in the current context.

1.1.2   Command Mode

all modes

1.1.3   Syntax Description

pol-name

Optional. NAT policy name.

detail

Optional. Displays more detailed information about the specified NAT policy. Used only with the pol-name argument.

1.1.4   Default

When entered without any optional syntax, the show nat policy command displays information for all configured NAT policies in the current context.

1.1.5   Usage Guidelines

Use the show nat policy command to display information for configured NAT policies in the current context.

Note:  
By default, most show commands (in any mode) display information for the current context only or, depending on the command syntax, for all contexts. If you are an administrator for the local context, you can insert the optional context ctx-name construct, preceding the show command, to view output for the specified context without entering that context. For more information about using the context ctx-name construct, see the context command description.

Note:  
By appending a space followed by the pipe ( | ) character at the end of a show command, you can filter the output using a set of modifier keywords and arguments. For more information, see “Modifying Output of show Commands” in Using the CLI.

1.1.6   Examples

The following example displays information about all configured NAT policies in the current context:

[local]Redback>show nat policy

Policy-Grid Rules  Slot-Mask   Binds  Policy-Name
0x00000001      4  0x00000010      1  pol1
0x00000002      1  0x00040000      1  pol2

The following example displays information about the pol1 policy:

[local]Redback#show nat policy pol1

Policy name       :  pol1
Policy grid       :  0x1
Number of rules   :  4
Slot mask         :  0x10
Number of binds   :  1

The following example displays detailed information about the pol1 policy:

[local]Redback#show nat policy pol1 detail

Policy name       :  pol1
Policy grid       :  0x1
Number of rules   :  4
Slot mask         :  0x10
Number of binds   :  1
  Circuit         :  3/1

Reference counters (in circuits * classes):
Slot     1     2     3     4     5     6     9    10    11    12    13    14
         0     0     1     0     0     0     0     0     0     0     0     0
    
Static NAT Rules:
In/Out  Protocol  Src-Addr         Port   NAT-Src-Addr     Port   NAT-Ctx-Id
in      tcp/ip    10.1.1.3         80     100.1.1.3        8080   0x40080001
in      tcp/ip    10.1.2.3         80     100.1.2.3        8080   0x40080001
in      tcp/ip    10.1.3.3         80     100.1.3.3        8080   0x40080001
in      tcp/ip    10.1.4.3         80     100.1.4.3        8080   0x40080001

Class-Name            Action  Pool-Grid  Pool-Ctx-Id  Timeout(sec)
default               na[p]t  0x2        0x40080001   tcp    86400 
                                                      udp    120   
Class-Name            Action  Pool-Grid/ Dest-IP-Addr/ Timeout(sec) 
			                              Context-Id Context-Id                 
default               na[p]t  0x2        170.16.1.1    tcp    86400 
                              0x40080001 0x40080001    udp    120   
                                                       finrst 240   
                                                       icmp   60    
                                                       syn    128   
                                                       basic  3600  
CLASS2                na[p]t  0x2        0x40080001    tcp    86400 
                                                       udp    120   
                                                       finrst 240   
                                                       icmp   60    
                                                       syn    128   
                                                       basic  3600  
CLASS3                na[p]t  0x0        0x40080001    tcp    86400 
                                                       udp    120   
                                                       finrst 240   
                                                       icmp   60    
                                                       syn    128   
                                                      basic  3600 

1.2   show nat pool

show nat pool [nat-pool-name [detail]]

1.2.1   Purpose

Displays information about configured Network Address Translation (NAT) pools in the current context.

1.2.2   Command Mode

all modes

1.2.3   Syntax Description

nat-pool-name

Optional. NAT pool name.

detail

Optional. Displays detailed information about the specified NAT pool.

1.2.4   Default

When entered without any optional syntax, the show nat pool command displays information about all configured NAT pools in the current context.

1.2.5   Usage Guidelines

Use the show nat pool command to display information about NAT pools in the current context.

Note:  
By default, most show commands (in any mode) display information for the current context only or, depending on the command syntax, for all contexts. If you are an administrator for the local context, you can insert the optional context ctx-name construct, preceding the show command, to view output for the specified context without entering that context. For more information about using the context ctx-name construct, see the context command description.

Note:  
By appending a space followed by the pipe ( | ) character at the end of a show command, you can filter the output using a set of modifier keywords and arguments. For more information, see “Modifying Output of show Commands” in Using the CLI.

1.2.6   Examples

The following example displays information for all configured NAT pools in the current context:

[local]Redback>show nat pool

Pool-Grid  Context-Id Type   Rcrds Slot-Mask  Pool-Name
0x00000002 0x40080001 napt/M     3 0x00040010 pool1
0x00000003 0x40080001 napt       1 0x00000000 pool_test

The following example displays detailed information about the pool1 pool:

[local]Redback>show nat pool pool1 detail

Pool name         :  pool1
Pool context id   :  0x40080001
Pool grid         :  0x2
Pool type         :  napt, multi-bind
Number of records :  3
Slot mask         :  0x40010


Reference counters (in circuits * classes):
Slot     1     2     3     4     5     6     9    10    11    12    13    14
         0     0     2     0     0     0     0     1     0     0     0     0
    
NAT Address Ranges:
Start-IP-Addr      End-IP-Addr      Start-Port  End-Port
100.1.1.3          100.1.1.3        45056       49151
100.1.1.3          100.1.1.3        49152       57343
100.1.1.3          100.1.1.3        57344       65535

1.3   show nd circuit

show nd circuit [circuit-handle | detail| interface]

1.3.1   Purpose

Displays Neighbor Discovery (ND) circuit information for one or more ND circuits.

1.3.2   Command Mode

all modes

1.3.3   Syntax Description

circuit-handle

Optional. Circuit handle of the circuit, in the following syntax: slot/port:channel:sub-channel/circuit-id.


  • slot—Chassis slot number of a traffic card to which the circuit is mapped.

  • port—Required if you enter the slot argument. Port number for the circuit.

  • channel—Channel number of the circuit.

  • sub-channel—Sub-channel number of the circuit.

  • circuit-id—Circuit ID number of circuit.


If circuit handle is omitted, circuit information for all circuits on the specified port or channel is displayed.

detail

Optional. Displays detailed ND circuit information.


interface

Optional. Displays all ND circuits bound to the interface.

1.3.4   Default

None

1.3.5   Usage Guidelines

Use the show nd circuit command to display ND circuit information for one or more ND circuits. Specify a circuit handle to display ND circuit information for the specified circuit. If the circuit handle is omitted, a summary for all circuits on the specified port or channel is displayed.

The following ND information is included in the detailed display for a specified ND circuit:

1.3.6   Examples

The following example displays ND circuit information for the circuit handle 1/4:1023:63/6/2/6:

[local]Redback>show nd circuit 1/4:1023:63/6/2/6
Circuit handle    : 1/4:1023:63/6/2/6    Intf grid      : 0x10000004
Mac addr          : 00:30:88:13:07:92    Status         : Up
Port type         : ethernet             Circuit type   : Subscriber
Interface name    : sub
Circuit MTU       : 1492                 Next RA message: 1(secs)
ND Profile        : profile7             IPv6 Proto State: Up
Subscriber Prefix : 3ffe:a:c:1::/64

1.4   show nd interface

show nd interface [if-name] [detail]

1.4.1   Purpose

Displays interface information for one or more Neighbor Discovery (ND) router interfaces.

1.4.2   Command Mode

1.4.3   Syntax Description

if-name

Optional. Name of an ND router interface.

detail

Optional. Displays detailed interface information.

1.4.4   Default

None

1.4.5   Usage Guidelines

Use the show nd interface command to display interface information for one or more ND router interfaces.

Note:  
By default, most show commands (in any mode) display information for the current context only or, depending on the command syntax, for all contexts. If you are an administrator for the local context, you can insert the optional context ctx-name construct, preceding the show command, to view output for the specified context without entering that context. For more information about using the context ctx-name construct, see the context command description.

Note:  
By appending a space followed by the pipe ( | ) character at the end of a show command, you can filter the output using a set of modifier keywords and arguments. For more information, see Modifying Output of show Commands in Using the CLI.

1.4.6   Examples

The following example displays interface information for the sub ND router interface, with all default settings:

[local]Redback>show nd interface sub
Intf Grid  Mac Address       Status Circuit             IPv6 Address
0x10000004 00:30:88:13:07:92 Up                         3ffe:a:c::1/48 (mbind)
Interface name: sub, link-local address fe80::230:88ff:fe04:20bf
Subscriber circuit count: 1
Interface parameters:
RA suppress: no                      RA reachable time(msec): 60000
RA interval(sec): 200                RA life time(sec): 1800
Managed address config: no           Other stateful config: no
Prefix valid life(sec): 2592000      Prefix preferred life(sec): 604800
NS Retry interval(msec): 5000

1.5   show nd neighbor

show nd neighbor [ipv6-addr | detail | interface if-name]

1.5.1   Purpose

Displays neighbor information for one or more Neighbor Discovery (ND) router interfaces.

1.5.2   Command Mode

1.5.3   Syntax Description

ipv6-addr

Optional. IP Version 6 (IPv6) address in the format A:B:C:D:E:F:G:H for which neighbor information is displayed.

detail

Optional. Displays detailed neighbor information.

interface if-name

Optional. Name of an ND router interface for which neighbor information is displayed.

1.5.4   Default

None

1.5.5   Usage Guidelines

Use the show nd neighbor command to display neighbor information for one or more ND router interfaces. Table 1 lists the fields displayed by this command without the detail keyword.

Table 1    Fields Displayed by the show nd neighbor Command

Field

Description

IPv6 Address

IPv6 address of the neighbor.

Age

Remaining time for which this neighbor is retained in the ND table.

Link-layer Addr

Medium access control (MAC) address of the neighbor.

State

Type of entry in the ND table, according to one of the following conditions:


  • intf—IPv6 address and MAC address are for a local interface.

  • reach—IPv6 address and MAC address are for an external router, which is reachable.

Circuit

Physical circuit (slot number and port) over which an advertisement message from this neighbor was received.

Table 2 lists the additional fields that are displayed with the detail keyword.

Table 2    Fields Displayed by the show nd neighbor detail Command

Field

Description

interface

Name of the ND interface for this neighbor.

entry has text attribute(s)

Type of attributes for this neighbor, such as:


  • dynamic (nbr NA pkt)—This entry was discovered dynamically with an Neighbor Advertisement (NA) message.

  • dynamic (nbr NS pkt)—This entry was discovered dynamically with an Neighbor Solicitation (NS) message.

  • dynamic (nbr RA pkt)—This entry was discovered dynamically with a Router Advertisement (RA) message.

  • interface—This entry is for the ND interface.

Router refresh in nnn seconds

Time until the next refresh.

reachable uptime dddhhhmm

Elapsed time that the neighbor has been reachable (days, hours, minutes).

number of times refreshed nnn

Number of times this neighbor entry has been refreshed during the reachable uptime period.

min/max request

Minimum and maximum number of NS messages sent during the reachable uptime period.

total NS/NA

Total number of NS and NA messages sent during the reachable uptime period.

min/max/avg resolution time

Minimum, maximum and average times to resolve this neighbor’s IP address, in milliseconds, during the reachable uptime period.

Note:  
By default, most show commands (in any mode) display information for the current context only or, depending on the command syntax, for all contexts. If you are an administrator for the local context, you can insert the optional context ctx-name construct, preceding the show command, to view output for the specified context without entering that context. For more information about using the context ctx-name construct, see the context command description.

Note:  
By appending a space followed by the pipe ( | ) character at the end of a show command, you can filter the output using a set of modifier keywords and arguments. For more information, see “Modifying Output of show Commands” in Using the CLI.

1.5.6   Examples

The following example displays the neighbors for the int1 ND router interface:

[local]Redback>show nd neighbor interface int1
IPv6 Address                    Age    Link-layer Addr   State  Circuit

2002::2                         0      00:30:88:00:11:0b intf   3/8

2005::1                         0      00:30:88:00:11:09 intf   3/6

2005::2                         269    00:30:88:00:32:94 reach  3/6

2006::1                         0      00:30:88:00:11:0f intf   3/12

fe80::230:88ff:fe00:1109        0      00:30:88:00:11:09 intf   3/6

fe80::230:88ff:fe00:110b        0      00:30:88:00:11:0b intf   3/8

fe80::230:88ff:fe00:110f        0      00:30:88:00:11:0f intf   3/12

fe80::230:88ff:fe00:3294        15     00:30:88:00:32:94 reach  3/6

fe80::2b0:64ff:fe2c:523         272    00:b0:64:2c:05:23 reach  3/12

The following example displays detailed information for the known neighbors; only the output for the 2005::1 IPv6 address is listed:

[local]Redback>show nd neighbor detail
IPv6 Address                    Age    Link-layer Addr   State  Circuit

2005::1                         139    00:30:88:00:11:09 reach  1/8

  interface: to_se2

 the entry has dynamic(nbr NS pkt) attribute(s), Router

 refresh in 160 sec, reachable uptime 02d15h57

 number of time refreshed 816, min/max request 1/1, total NS/NA 817/817

 min/max/avg resolution time 2/38/2 msec

1.6   show nd prefix

show nd prefix {all | interface {if-name | detail}}

1.6.1   Purpose

Displays prefix information for one or more Neighbor Discovery (ND) router interfaces.

1.6.2   Command Mode

1.6.3   Syntax Description

all

Displays prefix information for all ND router interfaces in the context.

interface

Displays prefix information for one or more ND router interfaces.

if-name

Name of an ND router interface.

detail

Displays detailed prefix information.

1.6.4   Default

None

1.6.5   Usage Guidelines

Use the show nd prefix command to display prefix information for one or more ND router interfaces. Table 3 lists the fields displayed by this command without the detail keyword.

Table 3    Fields Displayed by the show nd prefix Command

Field

Description

IPv6 Address

IPv6 address of the neighbor.

Onlink

State of the onlink configuration flag.

Autoconf

State of the auto-configuration flag.

ValidLife

Value for the Valid Lifetime field.

PrefLife

Value for the Preferred Lifetime field.

S

Status, according to one of the following conditions:


  • c—Prefix is explicitly configured with the prefix command (in ND router interface configuration mode).

  • i—Prefix is derived from the IPv6 address of the ND router interface.

Table 4 lists the fields displayed by this command with the detail keyword.

Table 4    Fields Displayed by the show nd prefix detail Command

Field

Description

Intf Grid

Internal system ID for the interface for this prefix.

Mac Address

Configured medium access control (MAC) address for this prefix.

Status

Physical circuit status, according to one of the following conditions:


  • Down—Circuit is not operational.

  • Up—Circuit is operational.

Circuit

Physical circuit ID, in one of the following formats:


  • Cct invalid—Circuit is not bound to an interface.

  • slot/port:internal circuit ID.

IPv6 Address

Configured IPv6 address for this prefix.

interface name

Name of the ND interface for this prefix.

link-local address

Link address, derived by the system from the MAC address for the port prefix.

Note:  
By default, most show commands (in any mode) display information for the current context only or, depending on the command syntax, for all contexts. If you are an administrator for the local context, you can insert the optional context ctx-name construct, preceding the show command, to view output for the specified context without entering that context. For more information about using the context ctx-name construct, see the context command description.

Note:  
By appending a space followed by the pipe ( | ) character at the end of a show command, you can filter the output using a set of modifier keywords and arguments. For more information, see “Modifying Output of show Commands” in Using the CLI.

1.6.6   Examples

The following example displays ND prefixes for all ND interfaces:

[local]Redback>show nd prefix all
ND prefix(es) on interface int1:
IPv6 Address                    Onlink  AutoConf  ValidLife  PrefLife   S
2005::1/64                      Y       Y         2592000    604800     i
2006::1/64                      Y       Y         2592000    604800     c
 on interface ipv6-tunnel:
2006::2/64                      Y       Y         2592000    604800     i

The following example displays detailed information for ND prefixes:

[local]Redback>show nd prefix interface detail
Intf Grid  Mac Address       Status Circuit             IPv6 Address
0x10000005 00:00:00:00:00:00 Down   Cct invalid         2005::1/64
  interface name: int1, link-local address ::
0x1000000a 00:00:00:00:00:00 Down   Cct invalid         2006::2/64
  interface name: ipv6-tunnel, link-local address ::

1.7   show nd profile

show nd profile [profile-name]

1.7.1   Purpose

Displays ND profile information for a context.

1.7.2   Command Mode

all modes

1.7.3   Syntax Description

profile-name

Optional. Name of an ND profile.

1.7.4   Default

None

1.7.5   Usage Guidelines

Use the show nd profile command to display ND profile information for a context. If the profile name is omitted from the command, then all ND profiles within the context (including the default profile GLOBAL_DEFAULT_PROFILE) is displayed. If an ND profile name is specified, all of the ND profile parameters for the specified profile are displayed.

Note:  
By default, most show commands (in any mode) display information for the current context only or, depending on the command syntax, for all contexts. If you are an administrator for the local context, you can insert the optional context ctx-name construct, preceding the show command, to view output for the specified context without entering that context. For more information about using the context ctx-name construct, see the context command description.

Note:  
By appending a space followed by the pipe ( | ) character at the end of a show command, you can filter the output using a set of modifier keywords and arguments. For more information, see “Modifying Output of show Commands” in Using the CLI.

1.7.6   Examples

The following example displays ND profile information for the profile profile7:

[local]Redback>show nd profile profile7
                --- ND Profile profile7 ---

Grid                : 4
RA Flags            : On-Link
RA Interval         : 5               RA Lifetime         : 1000
NS Retry            : 5000            # Subscriber Ckts   : 1
Preferred Lifetime  : 18000           Valid Lifetime      : 25000
# DAD Retries       : 1               IPV6 Down on DAD Failure: FALSE

The following example displays ND profile information for all ND profiles in the context, including GLOBAL_DEFAULT_PROFILE, the default profile:

[local]Redback>show nd profile
Profile Name                             Grid     Ckts
GLOBAL_DEFAULT_PROFILE                   0        0
profile7                                 4        1

1.8   show nd static-neighbor

show nd static-neighbor {all | interface {if-name | detail}}

1.8.1   Purpose

Displays information for the configured static neighbors for one or more Neighbor Discovery (ND) router interfaces.

1.8.2   Command Mode

1.8.3   Syntax Description

all

Displays static-neighbor information for all ND router interfaces in the context.

interface

Displays static-neighbor information for one or more ND router interfaces.

if-name

Name of an ND router interface.

detail

Displays detailed static-neighbor information.

1.8.4   Default

None

1.8.5   Usage Guidelines

Use the show nd static-neighbor command to display information for the configured static neighbors for one or more ND router interfaces.

Note:  
By default, most show commands (in any mode) display information for the current context only or, depending on the command syntax, for all contexts. If you are an administrator for the local context, you can insert the optional context ctx-name construct, preceding the show command, to view output for the specified context without entering that context. For more information about using the context ctx-name construct, see the context command description.

Note:  
By appending a space followed by the pipe ( | ) character at the end of a show command, you can filter the output using a set of modifier keywords and arguments. For more information, see “Modifying Output of show Commands” in Using the CLI.

1.8.6   Examples

The following example displays the static neighbors for the int1 ND router interface:

[local]Redback>show nd static-neighbor interface int1
ND static neighbor(s) on interface int1:

IPv6 Address                    Mac Address

2006::1                         00:30:88:00:0a:30

1.9   show nd statistics

show nd statistics [interface if-name]

1.9.1   Purpose

Displays global statistics for one or more Neighbor Discovery (ND) router interfaces.

1.9.2   Command Mode

1.9.3   Syntax Description

interface if-name

Optional. Name of an ND router interface for which statistics are displayed.

1.9.4   Default

None

1.9.5   Usage Guidelines

Use the show nd statistics command to display global statistics for one or more ND router interfaces. Table 5 lists the fields displayed by this command; entries are listed for each ND interface.

Table 5    Fields Displayed by the show nd statistics Command

Field

Description

RS

Number of Router Solicitation (RS) messages sent and received.

RA

Number of Router Advertisement (RA) messages sent and received.

NS

Number of Neighbor Solicitation (NS) messages sent and received.

NA

Number of Neighbor Advertisement (NA) messages sent and received.

OTHER

Number of other types of messages sent and received.

BAD

Number of malformed or unsupported messages sent and received.

TOTAL

Number of all types of messages sent and received.

cache miss/upload

Number of cache misses and uploads.

rib req/clear

Number of Routing Information Base (RIB) request and clear operations.

install/delete

Number of installation and deletion operations in the ND table.

total neighbor entries

Number of neighbor entries in the ND table (of all types).

static

Number of static neighbor entries in the ND table.

interface

Number of interface neighbor entries in the ND table.

subscriber

Number of subscriber neighbor cache entries in the ND table.

dynamic

Number of dynamic (discovered by the ND router for this interface) neighbor entries in the ND table.

total reachable neighbor entries

Number of neighbor entries in the ND table (of all types) that can be reached.

total subscriber ckts

Number of subscriber circuits.

up

Number of subscriber circuits currently in an up state.

ipv6 up

Number of subscriber circuits in which the IPv6 stack is in an up state.

down

Number of subscriber circuits currently in a down state.

deleted

Number of subscriber circuits deleted.

DAD reported

Number of duplicate IPv6 addresses detected.

last time stats cleared at hh:mm:ss ago

Last time that the global ND statistics were cleared (using the clear nd statistics all command).

Note:  
By default, most show commands (in any mode) display information for the current context only or, depending on the command syntax, for all contexts. If you are an administrator for the local context, you can insert the optional context ctx-name construct, preceding the show command, to view output for the specified context without entering that context. For more information about using the context ctx-name construct, see the context command description.

Note:  
By appending a space followed by the pipe ( | ) character at the end of a show command, you can filter the output using a set of modifier keywords and arguments. For more information, see “Modifying Output of show Commands” in Using the CLI.

1.9.6   Examples

The following example displays statistics for the int1 ND router interface:

[local]Redback>show nd statistics interface int1
ND statistics for interface int1:

       RS        RA        NS        NA        OTHER     BAD       TOTAL
 Send: 0         836       3008      3271      0         0         7115
 Recv: 0         819       3274      2979      15        0         7087

cache-miss/upload 4/0, rib req/clear 0/0, install/delete 836/4
 total neighbor entries 9; static 0, interface 6, subscriber 0 dynamic 3
 total reachable neighbor entries 7
 total subscriber ckts 5; up 5, ipv6 up 5, down 0, deleted 0
 Duplicate Addresses (DAD) reported 0
last time stats cleared at 21:04:19 ago

1.10   show nd summary

show nd summary

1.10.1   Purpose

Displays Neighbor Discovery (ND) summary information for the ND router global settings.

1.10.2   Command Mode

1.10.3   Syntax Description

This command has no keywords or arguments.

1.10.4   Default

None

1.10.5   Usage Guidelines

Use the show nd summary command to display ND summary information for the ND router global settings.

Note:  
By default, most show commands (in any mode) display information for the current context only or, depending on the command syntax, for all contexts. If you are an administrator for the local context, you can insert the optional context ctx-name construct, preceding the show command, to view output for the specified context without entering that context. For more information about using the context ctx-name construct, see the context command description.

Note:  
By appending a space followed by the pipe ( | ) character at the end of a show command, you can filter the output using a set of modifier keywords and arguments. For more information, see “Modifying Output of show Commands” in Using the CLI.

1.10.6   Examples

The following example displays ND summary information for the ND router global settings; in this case, the settings are all defaults:

[local]Redback>show nd summary
ND router global setting:



 RA suppress: no                     RA reachable time(msec): 0

 RA interval(sec): 200               RA life time(sec): 1800

 Managed address config: no          Other stateful config: no

 Prefix valid life(sec): 2592000     Prefix preferred life(sec): 604800

 NS interval(msec): 0

1.11   show netop

show netop {advertise | snmp version | connection-mode}

1.11.1   Purpose

Displays the configuration of the communication between the NetOp Element Management System (EMS) server and the SmartEdge router.

1.11.2   Command Mode

1.11.3   Syntax Description

advertise

Displays configuration information for advertisement packets.

snmp version

Displays the version of the SNMP traps that are sent to the NetOp EMS server.

connection-mode

Displays the type of encryption the SmartEdge router allows, if any, on the connection between the NetOp EMS server and the SmartEdge router.

1.11.4   Default

None

1.11.5   Usage Guidelines

Use the show netop command to display the configuration of the communication between the NetOp EMS server and the SmartEdge router.

This communication is configured by the connection mode command (in NetOp configuration mode); for information about this command, see the Command List.

Note:  
By default, most show commands (in any mode) display information for the current context only or, depending on the command syntax, for all contexts. If you are an administrator for the local context, you can insert the optional context ctx-name construct, preceding the show command, to view output for the specified context without entering that context. For more information about using the context ctx-name construct, see the context command description.

Note:  
By appending a space followed by the pipe ( | ) character at the end of a show command, you can filter the output using a set of modifier keywords and arguments. For more information, see “Modifying Output of show Commands” in Using the CLI.

1.11.6   Examples

The following example displays the configuration data for the advertisement packets sent to a NetOp EMS server:

[local]Redback>show netop advertise
IP Address      Port   Interval   Node Group

192.168.0.1     6581   10         NOCuser1

The following example shows that the SmartEdge router allows both unencrypted and Transport Layer Security (TLS) communication between itself and the NetOp EMS server:

[local]Redback>show netop connection-mode 



unencrypted

tls

1.12   show ntp associations

show ntp associations[remote-ip-addr] [detail [all-contexts]]

1.12.1   Purpose

Displays current associations among Network Time Protocol (NTP) servers and peers, and reports NTP daemon statistics.

1.12.2   Command Mode

all modes

1.12.3   Syntax Description

remote-ip-addr

Displays the status of a remote peer.

detail

Specifies detailed clock statistics.

all-contexts

Optional with the detail keyword; displays information for all contexts.

1.12.4   Default

None

1.12.5   Usage Guidelines

Use the show ntp associations command to display current associations among NTP servers, peers, and clients, and report NTP statistics. To display the status of a remote peer, add the remote-ip-addr argument. For NTP statistics for the current context, use the show ntp associations construct. To display data for all contexts add the all-contexts keyword.

Note:  
By default, most show commands (in any mode) display information for the current context only or, depending on the command syntax, for all contexts. If you are an administrator for the local context, you can insert the optional context ctx-name construct, preceding the show command, to view output for the specified context without entering that context. For more information about using the context ctx-name construct, see the context command description.

Note:  
By appending a space followed by the pipe ( | ) character at the end of a show command, you can filter the output using a set of modifier keywords and arguments. For more information, see “Modifying Output of show Commands” in Using the CLI.

1.12.6   Examples

The following example displays detailed NTP associations data for the current context:

[local]Redback#show ntp associations detail
remote 10.192.16.236, local 10.192.35.52
hmode client, pmode server, stratum 4, precision -18
leap 00, refid [155.53.174.12], rootdistance 0.26860, rootdispersion 0.13405
ppoll 10, hpoll 10, keyid 0, version 3, association 39940
valid 4, reach 067, unreach 0, flash 0x0000, boffset 0.00000, ttl/mode 0
timer 16589676s, flags config, bclient
reference time:      cf1aedc2.701da7fc  Mon, Feb  8 2010 12:08:34.437
originate timestamp: cf1af178.718ca2a0  Mon, Feb  8 2010 12:24:24.443
receive timestamp:   cf1af178.6f854046  Mon, Feb  8 2010 12:24:24.435
transmit timestamp:  cf1af0a3.f8394749  Mon, Feb  8 2010 12:20:51.969
filter delay:  0.00473  0.00461  0.00185  0.00194
               0.00272  1.00363  0.00000  0.00000
filter offset: 0.010296 0.010356 0.009153 0.009196
               0.010260 -0.48957 0.000000 0.000000
filter order:  1        0        2        3
               4        5        6        7
offset 0.010356, delay 0.00461, error bound 0.43840, filter error 0.17682
context id: 0x40080001

remote 155.53.12.12, local 10.192.35.52
hmode client, pmode server, stratum 4, precision -18
leap 00, refid [130.100.199.242], rootdistance 0.21339, rootdispersion 0.10818
ppoll 10, hpoll 10, keyid 0, version 3, association 39941
valid 7, reach 377, unreach 0, flash 0x0000, boffset 0.00000, ttl/mode 0
timer 16589676s, flags system_peer, config, bclient
reference time:      cf1ae73a.0b1e2476  Mon, Feb  8 2010 11:40:42.043
originate timestamp: cf1aeff7.493bfb9d  Mon, Feb  8 2010 12:17:59.286
receive timestamp:   cf1aeff7.b8f1b25f  Mon, Feb  8 2010 12:17:59.722
transmit timestamp:  cf1aeff7.40a54823  Mon, Feb  8 2010 12:17:59.252
filter delay:  0.46986  0.24446  0.05669  0.26521
               0.79604  0.81943  0.10710  0.06923
filter offset: -0.20143 -0.08754 0.007487 -0.10189
               -0.36687 -0.37947 -0.02487 -0.00480
filter order:  2        1        3        0
               4        5        6        7
offset 0.007487, delay 0.05669, error bound 0.17146, filter error 0.12712
context id: 0x40080001

1.13   show ntp status

show ntp status

1.13.1   Purpose

Displays the current Network Time Protocol (NTP) parameter settings and synchronization status.

1.13.2   Command Mode

all modes

1.13.3   Syntax Description

This command has no keywords or arguments.

1.13.4   Default

None

1.13.5   Usage Guidelines

Use the show ntp status command to display NTP parameter settings and synchronization status.

If the slowsync command (in NTP configuration mode) has not been enabled, it takes a few seconds for the NTP daemon to adjust time with valid NTP servers. While the NTP daemon is in the process of collecting samples from remote NTP servers, the Source is not synced yet message is displayed; see the “ Examples” section. For more information about the slowsync command, see the Command List.

Note:  
By default, most show commands (in any mode) display information for the current context only or, depending on the command syntax, for all contexts. If you are an administrator for the local context, you can insert the optional context ctx-name construct, preceding the show command, to view output for the specified context without entering that context. For more information about using the context ctx-name construct, see the context command description.

Note:  
By appending a space followed by the pipe ( | ) character at the end of a show command, you can filter the output using a set of modifier keywords and arguments. For more information, see “Modifying Output of show Commands” in Using the CLI.

1.13.6   Examples

The following example contains sample output in a case where synchronization has taken place after five minutes:

[local]Redback>show ntp status



Ntpd version 4.0.98f 

system peer: 155.53.12.12 

system peer mode: client 

leap indicator: 00 

stratum: 3 

precision: -15 

root distance: 0.02441 s 

root dispersion: 0.04129 s 

reference ID: [155.53.12.12] 

reference time: bde128a0.ea5204af Mon, Nov 21 2005 14:43:44.915 

system flags: bclient monitor ntp kernel stats kernel_sync 

jitter: 0.003784 s 

stability: 0.035 ppm 

broadcastdelay: 0.003998 s 

authdelay: 0.000000 s 

The following example shows sample output in a case where the NTP daemon has been started, but is in the process of trying to synchronize (within the first five minutes) with the remote server:

[local]Redback>show ntp status



Ntpd version 4.0.98f

Source is not synced yet

The following example shows sample output in a case where the daemon has not been started:

[local]Redback>show ntp status



Ntpd version 4.0.98f

... not running

1.14   show ospf

show ospf [instance-id]

1.14.1   Purpose

Displays high-level information for all Open Shortest Path First (OSPF) instances, or optionally, for a specific instance.

1.14.2   Command Mode

all modes

1.14.3   Syntax Description

instance-id

Optional. Instance ID. The range of values is 1 to 65,535.

1.14.4   Default

Displays OSPF instance information for all instances associated with the context.

1.14.5   Usage Guidelines

Use the show ospf command to display high-level information for all OSPF instances, or optionally, for a specific OSPF instance.

Note:  
By default, most show commands (in any mode) display information for the current context only or, depending on the command syntax, for all contexts. If you are an administrator for the local context, you can insert the optional context ctx-name construct, preceding the show command, to view output for the specified context without entering that context. For more information about using the context ctx-name construct, see the context command description.

Note:  
By appending a space followed by the pipe ( | ) character at the end of a show command, you can filter the output using a set of modifier keywords and arguments. For more information, see “Modifying Output of show Commands” in Using the CLI.

1.14.6   Examples

The following example displays output from the show ospf command for OSPF instance 1:

[local]Redback>show ospf 1
--- OSPF Instance 1/Router ID 193.10.25.7 ---



Intra-Distance  : 110               Inter-Distance  : 110

Ext-Distance    : 110               Type of Service : TOS-Type0

Area Border Rtr : Yes               AS Boundary Rtr : No

Auto-Cost       : Yes               Flood Queued    : 0

SPF Delay       : 1                 SPF Holdtime    : 1

Full SPF Count  : 3                 Incr SPF Count  : 0

Full SPF Vers   : 3                 Incr SPF Vers   : 0

SPF LastCompute : 00:02:19          Nbrs Exchanging : 0

Max Exchanging  : 30                Nbrs Adjacent   : 0

Redist Metric   : Unspecified       Redist Queued   : 0

Redist Count    : 0                 Redist Quantum  : 2000

Stub Rtr Config : None              Stub Rtr Delay  : 0

Stub Router     : No                BGP Converged   : No

MPLS Traffic Eng: No                MPLS Shortcuts  : No

Graceful Restart: Disabled          Restart Status  : No Restart

Helper Neighbors: 0



Area List (2 total):

0.0.0.0         0.0.0.1

1.15   show ospf3

show ospf3 [instance-id]

1.15.1   Purpose

Displays high-level information for all Open Shortest Path First Version 3 (OSPFv3) instances, or optionally, for a specific instance.

1.15.2   Command Mode

all modes

1.15.3   Syntax Description

instance-id

Optional. Instance ID. The range of values is 1 to 65,535.

1.15.4   Default

Displays OSPFv3 instance information for all instances associated with the context.

1.15.5   Usage Guidelines

Use the show ospf3 command to display high-level information for all OSPFv3 instances, or optionally, for a specific OSPFv3 instance.

Note:  
By default, most show commands (in any mode) display information for the current context only or, depending on the command syntax, for all contexts. If you are an administrator for the local context, you can insert the optional context ctx-name construct, preceding the show command, to view output for the specified context without entering that context. For more information about using the context ctx-name construct, see the context command description.

Note:  
By appending a space followed by the pipe ( | ) character at the end of a show command, you can filter the output using a set of modifier keywords and arguments. For more information, see “Modifying Output of show Commands” in Using the CLI.

1.15.6   Examples

The following example displays output from the show ospf3 command for OSPFv3 instance 1:

[local]Redback>show ospf3 1



  --- OSPFv3 Instance 1/Router ID 2.2.2.2 ---



Intra-Distance  : 110               Inter-Distance  : 110            

Ext-Distance    : 110               AS Scoped LSA   : 0              

Area Border Rtr : No                AS Boundary Rtr : No             

Auto-Cost       : Yes               Flood Queued    : 0              

SPF Delay       : 10                SPF Holdtime    : 0              

Full SPF Count  : 4                 Incr SPF Count  : 0              

Full SPF Vers   : 4                 Incr SPF Vers   : 0              

SPF LastCompute : 00:01:47          Nbrs Adjacent   : 2              

Nbrs Exchanging : 0                 Global Exchg Max: 300            

Redist Metric   : Unspecified       Redist Queued   : 0              

Redist Count    : 0                 Redist Quantum  : 2000           

Stub Rtr Config : None              Stub Rtr Delay  : 0              

Stub Router     : No                BGP Converged   : No             

MPLS Traffic Eng: No                MPLS Shortcuts  : No             

Demand DC Clear : 0                 Demand Indicate : 0              

Demand DoNotAge : 0                 Helper Neighbors: 0              

Graceful Restart: Disabled          Restart Status  : No Restart     

Helper StrictChk: No             



Area List (1 total):

0.0.0.0         

1.16   show ospf3 area

show ospf3 area [instance-id {area-id | ip-addr}] [brief]

1.16.1   Purpose

Displays information about Open Shortest Path First Version 3 (OSPFv3) areas.

1.16.2   Command Mode

all modes

1.16.3   Syntax Description

instance-id

Optional. Instance ID. The range of values is 1 to 65,535.

area-id

Optional. Area ID. The range of values is 0 to 4,294,967,295.

ip-addr

Optional. IP address.

brief

Optional. Provides a summary of information.

1.16.4   Default

Displays summary information for all OSPFv3 areas.

1.16.5   Usage Guidelines

Use the show ospf3 area command to display information about OSPFv3 areas.

Note:  
By default, most show commands (in any mode) display information for the current context only or, depending on the command syntax, for all contexts. If you are an administrator for the local context, you can insert the optional context ctx-name construct, preceding the show command, to view output for the specified context without entering that context. For more information about using the context ctx-name construct, see the context command description.

Note:  
By appending a space followed by the pipe ( | ) character at the end of a show command, you can filter the output using a set of modifier keywords and arguments. For more information, see “Modifying Output of show Commands” in Using the CLI.

1.16.6   Examples

The following example displays output from the show ospf3 area command:

[local]Redback>show ospf3 area



  --- OSPFv3 Area 0.0.0.0 Instance 1/Router ID 2.2.2.2 ---



Area Type      : Regular           Interface Count: 3              

LSA Count      : 13                LSA Checksum   : 0x06f2c6       

ABR Count      : 0                 ASBR Count     : 0              

Adjacent Nbrs  : 2                 Up Interfaces  : 3              

Demand DC Clear: 0                 Demand Indicate: 0              

Demand DoNotAge: 0                 Max Indicate ID: 0.0.0.0        



Interface ID List:

0.0.0.1         0.0.0.2         0.0.0.4         

The following example displays output from the show ospf3 area 1 0.0.0.0 command:

[local]Redback>show ospf3 area 1 0.0.0.0



  --- OSPFv3 Area 0.0.0.0 Instance 1/Router ID 2.2.2.2 ---



Area Type      : Regular           Interface Count: 3              

LSA Count      : 13                LSA Checksum   : 0x06f2c6       

ABR Count      : 0                 ASBR Count     : 0              

Adjacent Nbrs  : 2                 Up Interfaces  : 3              

Demand DC Clear: 0                 Demand Indicate: 0              

Demand DoNotAge: 0                 Max Indicate ID: 0.0.0.0        



Interface ID List:

0.0.0.1         0.0.0.2         0.0.0.4         

The following example displays output from the show ospf3 area brief command:

[local]Redback>show ospf3 area brief



  --- OSPFv3 Areas for Instance 1/Router ID 2.2.2.2 ---



Area            Type              Intf-Count  LSA-Count   LSA cksum

0.0.0.0         Regular           3           13          0x0006f2c6

1.17   show ospf3 asbr

show ospf3 asbr [instance-id [all]] [all]

1.17.1   Purpose

Displays routes to autonomous system boundary routers (ASBRs) and other Open Shortest Path First Version 3 (OSPFv3) routers.

1.17.2   Command Mode

all modes

1.17.3   Syntax Description

instance-id

Optional. Instance ID. The range of values is 1 to 65,535.

all

Optional. Displays information about ASBRs and other OSPFv3 routers.

1.17.4   Default

None

1.17.5   Usage Guidelines

Use the show ospf3 asbr command to display routes to ASBRs and other OSPFv3 routers.

Note:  
By default, most show commands (in any mode) display information for the current context only or, depending on the command syntax, for all contexts. If you are an administrator for the local context, you can insert the optional context ctx-name construct, preceding the show command, to view output for the specified context without entering that context. For more information about using the context ctx-name construct, see the context command description.

Note:  
By appending a space followed by the pipe ( | ) character at the end of a show command, you can filter the output using a set of modifier keywords and arguments. For more information, see “Modifying Output of show Commands” in Using the CLI.

1.17.6   Examples

The following example displays routes to all ASBRs:

[local]Redback>show ospf3 asbr



  --- ASBR entries for OSPFv3 Instance 1/Router ID 2.2.2.2 ---



Destination    Cost  Route-Type Area           NextHop

3.3.3.3        1     Intra      0.0.0.0        fe80::230:88ff:fe00:3294

The following example displays routes to ASBR 5:

[local]Redback>show ospf3 asbr 5



  --- ASBR entries for OSPFv3 Instance 5/Router ID 2.2.2.2 ---



Destination    Cost  Route-Type Area           NextHop

3.3.3.3        1     Intra      0.0.0.0        1280::230:88fd:fe00:3567

The following example displays routes to all ASBRs and other OSPFv3 routes:

[local]Redback>show ospf3 asbr all



  --- ASBR entries for OSPFv3 Instance 1/Router ID 2.2.2.2 ---



Destination    Cost  Route-Type Area           NextHop

3.3.3.3        1     Intra      0.0.0.0        fe80::230:88ff:fe00:3294

1.18   show ospf3 database

show ospf3 database [instance-id] [area-id | ip-addr] [detail] [summary]

1.18.1   Purpose

Displays information stored in the Open Shortest Path First Version 3 (OSPFv3) link-state database (LSDB).

1.18.2   Command Mode

all modes

1.18.3   Syntax Description

instance-id

Optional. OSPFv3 instance ID. The range of values is 1 to 65,535.

area-id

Optional. Area ID. The range of values is 0 to 4,294,967,295.

ip-addr

Optional. Area IP address.

detail

Optional. Displays detailed information.

summary

Optional. Displays summary information.

1.18.4   Default

None

1.18.5   Usage Guidelines

Use the show ospf3 database command to display information stored in the OSPFv3 LSD.

Note:  
By default, most show commands (in any mode) display information for the current context only or, depending on the command syntax, for all contexts. If you are an administrator for the local context, you can insert the optional context ctx-name construct, preceding the show command, to view output for the specified context without entering that context. For more information about using the context ctx-name construct, see the context command description.

Note:  
By appending a space followed by the pipe ( | ) character at the end of a show command, you can filter the output using a set of modifier keywords and arguments. For more information, see “Modifying Output of show Commands” in Using the CLI.

1.18.6   Examples

The following example provides information about link-state advertisement (LSA) type, link ID, advertising router IP address, link-state age, checksums, and sequence number:

[local]Redback>show ospf3 database



  --- OSPFv3 Link State Database for Instance 1/Router ID 2.2.2.2 ---



         Router Link State Advertisements (Area 0.0.0.0)

LinkID           AdvertisingRtr   Sequence #  ChkSm  Length   LSAge

0.0.0.0          2.2.2.2          80000006    9b12   56       440

0.0.0.0          3.3.3.3          80000005    7336   56       90

0.0.0.0          4.4.4.4          80000198    bf3b   56       410



         Network Link State Advertisements (Area 0.0.0.0)

LinkID           AdvertisingRtr   Sequence #  ChkSm  Length   LSAge

0.0.0.4          2.2.2.2          80000001    6781   32       440

0.0.0.5          4.4.4.4          80000001    6572   32       432

0.0.0.6          4.4.4.4          80000001    29b1   32       457



         Intra Area Prefix Link State Advertisements (Area 0.0.0.0)

LinkID           AdvertisingRtr   Sequence #  ChkSm  Length   LSAge

0.0.0.0          2.2.2.2          8000000a    1b04   52       440

0.0.0.4          2.2.2.2          80000001    b996   52       440

0.0.0.0          3.3.3.3          80000006    59c0   52       433

0.0.3.237        4.4.4.4          80000001    cf80   52       432

0.0.3.238        4.4.4.4          80000001    bb93   52       457



         Link Type Link State Advertisements (Area 0.0.0.0) 

LinkID           AdvertisingRtr   Sequence #  ChkSm  Length   LSAge

0.0.0.2          2.2.2.2          80000001    d92d   64       462

0.0.0.6          4.4.4.4          80000002    4524   64       1678

0.0.0.2          10.12.209.174    80000001    86f1   64       600

0.0.0.4          2.2.2.2          80000001    21ea   64       462

0.0.0.4          3.3.3.3          80000001    b8a2   64       445

0.0.0.4          10.12.209.163    80000001    c516   64       1283

0.0.0.4          10.12.209.174    80000001    cdaf   64       600



         External Link State Advertisements

LinkID           AdvertisingRtr   Sequence #  ChkSm  Length   LSAge

0.0.0.18         3.3.3.3          80000001    3829   36       90

0.0.0.19         3.3.3.3          80000001    aaa4   36       90

1.19   show ospf3 database advertising router

show ospf3 database [instance-id] [area-id | ip-addr] advertising router {router-id | self-originate} [detail [debug] | debug]

1.19.1   Purpose

Displays information about Open Shortest Path First Version 3 (OSPFv3) advertising router link-state advertisements (LSAs).

1.19.2   Command Mode

all modes

1.19.3   Syntax Description

instance-id

Optional. OSPFv3 instance ID. The range of values is 1 to 65,535.

area-id

Optional. Area ID. The range of values is 0 to 4,294,967,295.

ip-addr

Optional. Area IP address.

router-id

OSPFv3 router ID in the form A.B.C.D.

self-originate

Displays self-originated LSAs.

detail

Optional. Provides detailed information.

debug

Optional. Displays debug information.

1.19.4   Default

None

1.19.5   Usage Guidelines

Use the show ospf3 database advertising router command to display information about OSPFv3 advertising router LSAs.

Note:  
By default, most show commands (in any mode) display information for the current context only or, depending on the command syntax, for all contexts. If you are an administrator for the local context, you can insert the optional context ctx-name construct, preceding the show command, to view output for the specified context without entering that context. For more information about using the context ctx-name construct, see the context command description.

Note:  
By appending a space followed by the pipe ( | ) character at the end of a show command, you can filter the output using a set of modifier keywords and arguments. For more information, see “Modifying Output of show Commands” in Using the CLI.

1.19.6   Examples

The following example provides information specific to the advertising router, 3.3.3.3:

[local]Redback>show ospf3 database advertising-router 3.3.3.3



  --- OSPFv3 Link State Database for Instance 1/Router ID 2.2.2.2 ---



         Router Link State Advertisements (Area 0.0.0.0)

LinkID           AdvertisingRtr   Sequence #  ChkSm  Length   LSAge

0.0.0.0          3.3.3.3          80000005    7336   56       127



         Intra Area Prefix Link State Advertisements (Area 0.0.0.0)

LinkID           AdvertisingRtr   Sequence #  ChkSm  Length   LSAge

0.0.0.0          3.3.3.3          80000006    59c0   52       470



         Link Type Link State Advertisements (Area 0.0.0.0) 

LinkID           AdvertisingRtr   Sequence #  ChkSm  Length   LSAge

0.0.0.4          3.3.3.3          80000001    b8a2   64       482



         External Link State Advertisements

LinkID           AdvertisingRtr   Sequence #  ChkSm  Length   LSAge

0.0.0.18         3.3.3.3          80000001    3829   36       127

0.0.0.19         3.3.3.3          80000001    aaa4   36       127

1.20   show ospf3 database grace

show ospf3 database [instance-id] [area-id | ip-addr] grace [all [router-id] | link-id [router-id | self-originate] | self-originate] [detail [debug] | debug]

1.20.1   Purpose

Displays information about Open Shortest Path First Version 3 (OSPFv3) grace link-state advertisement (LSA) database entries.

1.20.2   Command Mode

all modes

1.20.3   Syntax Description

instance-id

Optional. OSPFv3 instance ID. The range of values is 1 to 65,535.

area-id

Optional. Area ID. The range of values is 0 to 4,294,967,295.

ip-addr

Optional. Area IP address.

all

Optional. Displays all grace LSAs.

router-id

Optional. Advertising router ID in the form A.B.C.D.

link-id

Optional. LSA ID in the form A.B.C.D.

self-originate

Optional. Displays self-originated LSAs.

detail

Optional. Provides detailed information.

debug

Optional. Displays debug information.

1.20.4   Default

None

1.20.5   Usage Guidelines

Use the show ospf3 database grace command to display information about OSPFv3 grace LSA database entries.

Note:  
By default, most show commands (in any mode) display information for the current context only or, depending on the command syntax, for all contexts. If you are an administrator for the local context, you can insert the optional context ctx-name construct, preceding the show command, to view output for the specified context without entering that context. For more information about using the context ctx-name construct, see the context command description.

Note:  
By appending a space followed by the pipe ( | ) character at the end of a show command, you can filter the output using a set of modifier keywords and arguments. For more information, see “Modifying Output of show Commands” in Using the CLI.

1.20.6   Examples

The following example displays general output from the show ospf3 database grace command:

[local]Redback>show ospf3 database grace

  --- OSPFv3 Link State Database for Instance 1/Router ID 2.2.2.2 ---

         Grace Link State Advertisements (Area 0.0.0.0)
LinkID           AdvertisingRtr   Sequence #  ChkSm  Length   LSAge
0.0.0.4          2.2.2.2          80000001    bb07   36       59

The following example displays detailed output from the show ospf3 database grace command:

[local]Redback>show ospf3 database grace detail

  --- OSPFv3 Link State Database for Instance 1/Router ID 2.2.2.2 ---

        --- Grace LSA 0.0.0.4 (Area 0.0.0.0) ---

Link State Id     : 0.0.0.4            Advertising Router   : 2.2.2.2        
Sequence Number   : 0x80000001         Checksum             : 0xbb07           
Length            : 36             

1.21   show ospf3 database inter-prefix

show ospf3 database [instance-id] [area-id | ip-addr] inter-prefix [all [router-id] | link-id [router-id | self-originate] | self-originate] [detail [debug] | debug]

1.21.1   Purpose

Displays information about Open Shortest Path First Version 3 (OSPFv3) interarea prefix link-state advertisement (LSA) database entries.

1.21.2   Command Mode

all modes

1.21.3   Syntax Description

instance-id

Optional. OSPFv3 instance ID. The range of values is 1 to 65,535.

area-id

Optional. Area ID. The range of values is 0 to 4,294,967,295.

ip-addr

Optional. Area IP address.

all

Optional. Displays all interarea prefix LSAs.

router-id

Optional. Advertising router ID in the form A.B.C.D.

link-id

Optional. LSA ID in the form A.B.C.D.

self-originate

Optional. Displays self-originated LSAs.

detail

Optional. Provides detailed information.

debug

Optional. Displays debug information.

1.21.4   Default

None

1.21.5   Usage Guidelines

Use the show ospf3 database inter-prefix command to display information about OSPFv3 interarea prefix LSA database entries.

Note:  
By default, most show commands (in any mode) display information for the current context only or, depending on the command syntax, for all contexts. If you are an administrator for the local context, you can insert the optional context ctx-name construct, preceding the show command, to view output for the specified context without entering that context. For more information about using the context ctx-name construct, see the context command description.

Note:  
By appending a space followed by the pipe ( | ) character at the end of a show command, you can filter the output using a set of modifier keywords and arguments. For more information, see “Modifying Output of show Commands” in Using the CLI.

1.21.6   Examples

The following example displays general output from the show ospf3 database inter-prefix command:

[local]Redback>show ospf3 database inter-prefix

  --- OSPFv3 Link State Database for Instance 1/Router ID 2.2.2.2 ---

         Inter Area Prefix Link State Advertisements (Area 0.0.0.0)
LinkID           AdvertisingRtr   Sequence #  ChkSm  Length   LSAge
0.0.0.15         3.3.3.3          80000002    d997   44       763

The following example displays detailed output from the show ospf3 database inter-prefix command:

[local]Redback>show ospf3 database inter-prefix detail

  --- OSPFv3 Link State Database for Instance 1/Router ID 2.2.2.2 ---

        --- Inter Area Prefix LSA 0.0.0.15 (Area 0.0.0.0) ---

Link State Id     : 0.0.0.15           Advertising Router   : 3.3.3.3        
Sequence Number   : 0x80000002         Checksum             : 0xd997           
Length            : 44             
Age               : 767                Metric : 10                      
IPV6Prefix        : 2007::/112 

1.22   show ospf3 database inter-router

show ospf3 database [instance-id] [area-id | ip-addr] inter-router [all [router-id] | link-id [router-id | self-originate] | self-originate] [detail [debug] | debug]

1.22.1   Purpose

Displays information about Open Shortest Path First Version 3 (OSPFv3) interarea router link-state advertisement (LSA) database entries.

1.22.2   Command Mode

all modes

1.22.3   Syntax Description

instance-id

Optional. OSPFv3 instance ID. The range of values is 1 to 65,535.

area-id

Optional. Area ID. The range of values is 0 to 4,294,967,295.

ip-addr

Optional. Area IP address.

all

Optional. Displays all interarea router LSAs.

router-id

Optional. Advertising router ID in the form A.B.C.D.

link-id

Optional. LSA ID in the form A.B.C.D.

self-originate

Optional. Displays self-originated LSAs.

detail

Optional. Provides detailed information.

debug

Optional. Displays debug information.

1.22.4   Default

None

1.22.5   Usage Guidelines

Use the show ospf3 database inter-router command to display information about OSPFv3 interarea router LSA database entries.

Note:  
By default, most show commands (in any mode) display information for the current context only or, depending on the command syntax, for all contexts. If you are an administrator for the local context, you can insert the optional context ctx-name construct, preceding the show command, to view output for the specified context without entering that context. For more information about using the context ctx-name construct, see the context command description.

Note:  
By appending a space followed by the pipe ( | ) character at the end of a show command, you can filter the output using a set of modifier keywords and arguments. For more information, see “Modifying Output of show Commands” in Using the CLI.

1.22.6   Examples

The following example displays general output from the show ospf3 database inter-router command:

[local]Redback>show ospf3 database inter-router

  --- OSPFv3 Link State Database for Instance 1/Router ID 2.2.2.2 ---

         Inter Area Router Link State Advertisements (Area 0.0.0.0)
LinkID           AdvertisingRtr   Sequence #  ChkSm  Length   LSAge
0.0.0.20         3.3.3.3          80000001    deed   32       644

The following example displays detailed output from the show ospf3 database inter-router command:

[local]Redback>show ospf3 database inter-router detail

  --- OSPFv3 Link State Database for Instance 1/Router ID 2.2.2.2 ---

        --- Inter Area Router LSA 0.0.0.20 (Area 0.0.0.0) ---

Link State Id     : 0.0.0.20           Advertising Router   : 3.3.3.3        
Sequence Number   : 0x80000001         Checksum             : 0xdeed           
Length            : 32                 Options              : V6,E,R,DC
Metric            : 10                 Age                  : 647            
Router-Id         : 4.4.4.4

1.23   show ospf3 database intra-prefix

show ospf3 database [instance-id] [area-id | ip-addr] inter-router [all [router-id] | link-id [router-id | self-originate] | self-originate] [detail [debug] | debug]

1.23.1   Purpose

Displays information about Open Shortest Path First Version 3 (OSPFv3) intra-area prefix link-state advertisement (LSA) database entries.

1.23.2   Command Mode

all modes

1.23.3   Syntax Description

instance-id

Optional. OSPFv3 instance ID. The range of values is 1 to 65,535.

area-id

Optional. Area ID. The range of values is 0 to 4,294,967,295.

ip-addr

Optional. Area IP address.

all

Optional. Displays all intra-area prefix LSAs.

router-id

Optional. Advertising router ID in the form A.B.C.D.

link-id

Optional. LSA ID in the form A.B.C.D.

self-originate

Optional. Displays self-originated LSAs.

detail

Optional. Provides detailed information.

debug

Optional. Displays debug information.

1.23.4   Default

None

1.23.5   Usage Guidelines

Use the show ospf3 database intra-prefix command to display information about OSPFv3 intra-area prefix LSA database entries.

Note:  
By default, most show commands (in any mode) display information for the current context only or, depending on the command syntax, for all contexts. If you are an administrator for the local context, you can insert the optional context ctx-name construct, preceding the show command, to view output for the specified context without entering that context. For more information about using the context ctx-name construct, see the context command description.

Note:  
By appending a space followed by the pipe ( | ) character at the end of a show command, you can filter the output using a set of modifier keywords and arguments. For more information, see “Modifying Output of show Commands” in Using the CLI.

1.23.6   Examples

The following example displays output from the show ospf3 database intra-prefix command:

[local]Redback>show ospf3 database intra-prefix



  --- OSPFv3 Link State Database for Instance 1/Router ID 2.2.2.2 ---



         Intra Area Prefix Link State Advertisements (Area 0.0.0.0)

LinkID           AdvertisingRtr   Sequence #  ChkSm  Length   LSAge

0.0.0.0          2.2.2.2          8000000a    1b04   52       572

0.0.0.4          2.2.2.2          80000001    b996   52       572

0.0.0.0          3.3.3.3          80000006    59c0   52       565

0.0.3.237        4.4.4.4          80000001    cf80   52       564

0.0.3.238        4.4.4.4          80000001    bb93   52       589

1.24   show ospf3 database link

show ospf3 database [instance-id] [area-id | ip-addr] link [all [router-id] | link-id [router-id | self-originate] | self-originate] [detail [debug] | debug]

1.24.1   Purpose

Displays information about Open Shortest Path First Version 3 (OSPFv3) link link-state advertisements (LSAs).

1.24.2   Command Mode

all modes

1.24.3   Syntax Description

instance-id

Optional. OSPFv3 instance ID. The range of values is 1 to 65,535.

area-id

Optional. Area ID. The range of values is 0 to 4,294,967,295.

ip-addr

Optional. Area IP address.

all

Optional. Displays all link LSAs.

router-id

Optional. Advertising router ID in the form A.B.C.D.

link-id

Optional. LSA ID in the form A.B.C.D.

self-originate

Optional. Displays self-originated LSAs.

detail

Optional. Provides detailed information.

debug

Optional. Displays debug information.

1.24.4   Default

None

1.24.5   Usage Guidelines

Use the show ospf3 database link command to display information about OSPFv3 link LSAs.

Note:  
By default, most show commands (in any mode) display information for the current context only or, depending on the command syntax, for all contexts. If you are an administrator for the local context, you can insert the optional context ctx-name construct, preceding the show command, to view output for the specified context without entering that context. For more information about using the context ctx-name construct, see the context command description.

Note:  
By appending a space followed by the pipe ( | ) character at the end of a show command, you can filter the output using a set of modifier keywords and arguments. For more information, see “Modifying Output of show Commands” in Using the CLI.

1.24.6   Examples

The following example displays output from the show ospf3 database link command:

[local]Redback>show ospf3 database link

  --- OSPFv3 Link State Database for Instance 1/Router ID 2.2.2.2 ---

         Link Type Link State Advertisements (Area 0.0.0.0) (Interface 0.0.0.2)
LinkID           AdvertisingRtr   Sequence #  ChkSm  Length   LSAge
0.0.0.2          2.2.2.2          80000001    d92d   64       614
0.0.0.6          4.4.4.4          80000002    4524   64       1830
0.0.0.2          10.12.209.174    80000001    86f1   64       752

         Link Type Link State Advertisements (Area 0.0.0.0) (Interface 0.0.0.4)
LinkID           AdvertisingRtr   Sequence #  ChkSm  Length   LSAge
0.0.0.4          2.2.2.2          80000001    21ea   64       614
0.0.0.4          3.3.3.3          80000001    b8a2   64       597
0.0.0.4          10.12.209.163    80000001    c516   64       1435
0.0.0.4          10.12.209.174    80000001    cdaf   64       752

1.25   show ospf3 database network

show ospf3 database [instance-id] [area-id | ip-addr] network [all [router-id] | link-id [router-id | self-originate] | self-originate] [detail [debug] | debug]

1.25.1   Purpose

Displays information about Open Shortest Path First Version 3 (OSPFv3) network link-state advertisements (LSAs).

1.25.2   Command Mode

all modes

1.25.3   Syntax Description

instance-id

Optional. OSPFv3 instance ID. The range of values is 1 to 65,535.

area-id

Optional. Area ID. The range of values is 0 to 4,294,967,295.

ip-addr

Optional. Area IP address.

all

Optional. Displays all network LSAs.

router-id

Optional. Advertising router ID in the form A.B.C.D.

link-id

Optional. LSA ID in the form A.B.C.D.

self-originate

Optional. Displays self-originated LSAs.

detail

Optional. Provides detailed information.

debug

Optional. Displays debug information.

1.25.4   Default

None

1.25.5   Usage Guidelines

Use the show ospf3 database network command to display information about OSPFv3 network LSAs.

Note:  
By default, most show commands (in any mode) display information for the current context only or, depending on the command syntax, for all contexts. If you are an administrator for the local context, you can insert the optional context ctx-name construct, preceding the show command, to view output for the specified context without entering that context. For more information about using the context ctx-name construct, see the context command description.

Note:  
By appending a space followed by the pipe ( | ) character at the end of a show command, you can filter the output using a set of modifier keywords and arguments. For more information, see “Modifying Output of show Commands” in Using the CLI.

1.25.6   Examples

The following example displays information specific to network LSAs:

[local]Redback>show ospf3 database network



  --- OSPFv3 Link State Database for Instance 1/Router ID 2.2.2.2 ---



         Network Link State Advertisements (Area 0.0.0.0)

LinkID           AdvertisingRtr   Sequence #  ChkSm  Length   LSAge

0.0.0.4          2.2.2.2          80000001    6781   32       607

0.0.0.5          4.4.4.4          80000001    6572   32       599

0.0.0.6          4.4.4.4          80000001    29b1   32       624

1.26   show ospf3 database nssa

show ospf3 database [instance-id] [area-id | ip-addr] nssa [[all [router-id] | link-id [router-id | self-originate] | self-originate] [detail [debug] | debug]

1.26.1   Purpose

Displays information about Open Shortest Path First Version 3 (OSPFv3) not-so-stubby-area (NSSA) link-state advertisements (LSAs).

1.26.2   Command Mode

all modes

1.26.3   Syntax Description

instance-id

Optional. OSPFv3 instance ID. The range of values is 1 to 65,535.

area-id

Optional. Area ID. The range of values is 0 to 4,294,967,295.

ip-addr

Optional. Area IP address.

all

Optional. Displays all NSSA LSAs.

router-id

Optional. Advertising router ID in the form A.B.C.D.

link-id

Optional. LSA ID in the form A.B.C.D.

self-originate

Optional. Displays self-originated LSAs.

detail

Optional. Provides detailed information.

debug

Optional. Displays debug information.

1.26.4   Default

None

1.26.5   Usage Guidelines

Use the show ospf3 database nssa command to display information about OSPFv3 NSSA LSAs.

Note:  
By default, most show commands (in any mode) display information for the current context only or, depending on the command syntax, for all contexts. If you are an administrator for the local context, you can insert the optional context ctx-name construct, preceding the show command, to view output for the specified context without entering that context. For more information about using the context ctx-name construct, see the context command description.

Note:  
By appending a space followed by the pipe ( | ) character at the end of a show command, you can filter the output using a set of modifier keywords and arguments. For more information, see “Modifying Output of show Commands” in Using the CLI.

1.26.6   Examples

The following example displays general output from the show ospf3 database nssa command:

[local]Redback>show ospf3 database nssa



  --- OSPFv3 Link State Database for Instance 1/Router ID 3.3.3.3 ---



         NSSA Link State Advertisements (Area 0.0.0.3)

LinkID           AdvertisingRtr   Sequence #  ChkSm  Length   LSAge

0.0.0.0          3.3.3.3          80000002    bcdf   44       1126

The following example displays detailed output from the show ospf3 database nssa command:

[local]Redback>show ospf3 database nssa detail



  --- OSPFv3 Link State Database for Instance 1/Router ID 3.3.3.3 ---



        --- NSSA LSA 0.0.0.0 (Area 0.0.0.3) ---



Link State Id     : 0.0.0.0            Advertising Router   : 3.3.3.3

Sequence Number   : 0x80000002         Checksum             : 0xbcdf

Length            : 44             

Prefix Len        : 128                Metric               : 1

Options           : 0x0                Flags                : 0x0

Metric-Type       : TYPE1            

IPV6 Prefix       : ::/128 

1.27   show ospf3 database router

show ospf3 database [instance-id] [area-id | ip-addr] router [all [router-id] | link-id [router-id | self-originate] | self-originate] [detail [debug] | debug]

1.27.1   Purpose

Displays information about Open Shortest Path First Version 3 (OSPFv3) router link-state advertisements (LSAs).

1.27.2   Command Mode

all modes

1.27.3   Syntax Description

instance-id

Optional. OSPFv3 instance ID. The range of values is 1 to 65,535.

area-id

Optional. Area ID. The range of values is 0 to 4,294,967,295.

ip-addr

Optional. Area IP address.

all

Optional. Displays all router LSAs.

router-id

Optional. Advertising router ID in the form A.B.C.D.

link-id

Optional. LSA ID in the form A.B.C.D.

self-originate

Optional. Displays self-originated LSAs.

detail

Optional. Provides detailed information.

debug

Optional. Displays debug information.

1.27.4   Default

None

1.27.5   Usage Guidelines

Use the show ospf3 database router command to display information about OSPFv3 router LSAs.

Note:  
By default, most show commands (in any mode) display information for the current context only or, depending on the command syntax, for all contexts. If you are an administrator for the local context, you can insert the optional context ctx-name construct, preceding the show command, to view output for the specified context without entering that context. For more information about using the context ctx-name construct, see the context command description.

Note:  
By appending a space followed by the pipe ( | ) character at the end of a show command, you can filter the output using a set of modifier keywords and arguments. For more information, see “Modifying Output of show Commands” in Using the CLI.

1.27.6   Examples

The following example displays general output from the show ospf3 database router command:

[local]Redback>show ospf3 database router



  --- OSPFv3 Link State Database for Instance 1/Router ID 2.2.2.2 ---



         Router Link State Advertisements (Area 0.0.0.0)

LinkID           AdvertisingRtr   Sequence #  ChkSm  Length   LSAge

0.0.0.0          2.2.2.2          80000006    9b12   56       628

0.0.0.0          3.3.3.3          80000005    7336   56       278

0.0.0.0          4.4.4.4          80000198    bf3b   56       598

The following example displays detailed output from the show ospf3 database router command:

[local]Redback>show ospf3 database router detail



  --- OSPFv3 Link State Database for Instance 1/Router ID 2.2.2.2 ---



        --- Router LSA 0.0.0.0 (Area 0.0.0.0) ---



Link State Id     : 0.0.0.0            Advertising Router   : 2.2.2.2

Sequence Number   : 0x80000006         Checksum             : 0x9b12

Length            : 56                 Options              : V6,E,R,DC

RouterBits        :                    LinkCount            : 2       

Age               : 645



Link Type     : transit     Interface Id              : 0.0.0.2        

Link Metric   : 10          NBR Interface Id          : 0.0.0.6        

NBR Router Id : 4.4.4.4         



Link Type     : transit     Interface Id              : 0.0.0.4        

Link Metric   : 1           NBR Interface Id          : 0.0.0.4        

NBR Router Id : 2.2.2.2         





        --- Router LSA 0.0.0.0 (Area 0.0.0.0) ---



Link State Id     : 0.0.0.0            Advertising Router   : 3.3.3.3

Sequence Number   : 0x80000005         Checksum             : 0x7336 

Length            : 56                 Options              : V6,E,R,DC

RouterBits        : E                  LinkCount            : 2      

Age               : 295



Link Type     : transit     Interface Id              : 0.0.0.2      

Link Metric   : 10          NBR Interface Id          : 0.0.0.5      

NBR Router Id : 4.4.4.4         



Link Type     : transit     Interface Id              : 0.0.0.4    

Link Metric   : 1           NBR Interface Id          : 0.0.0.4     

NBR Router Id : 2.2.2.2         





        --- Router LSA 0.0.0.0 (Area 0.0.0.0) ---



Link State Id     : 0.0.0.0            Advertising Router   : 4.4.4.4

Sequence Number   : 0x80000198         Checksum             : 0xbf3b 

Length            : 56                 Options              : V6,E,R,DC

RouterBits        :                    LinkCount            : 2

Age               : 615



Link Type     : transit     Interface Id              : 0.0.0.6

Link Metric   : 10          NBR Interface Id          : 0.0.0.6

NBR Router Id : 4.4.4.4         



Link Type     : transit     Interface Id              : 0.0.0.5

Link Metric   : 10          NBR Interface Id          : 0.0.0.5

NBR Router Id : 4.4.4.4         

1.28   show ospf3 debug

show ospf3 debug

1.28.1   Purpose

Displays Open Shortest Path First Version 3 (OSPFv3) debug information.

1.28.2   Command Mode

all modes

1.28.3   Syntax Description

This command has no keywords or arguments.

1.28.4   Default

None

1.28.5   Usage Guidelines

Use the show ospf3 debug command to display OSPFv3 debug information.

Note:  
By default, most show commands (in any mode) display information for the current context only or, depending on the command syntax, for all contexts. If you are an administrator for the local context, you can insert the optional context ctx-name construct, preceding the show command, to view output for the specified context without entering that context. For more information about using the context ctx-name construct, see the context command description.

Note:  
By appending a space followed by the pipe ( | ) character at the end of a show command, you can filter the output using a set of modifier keywords and arguments. For more information, see “Modifying Output of show Commands” in Using the CLI.

1.28.6   Examples

The following example displays output from the show ospf3 debug command:

[local]Redback>show ospf3 debug



  --- OSPFv3 Debug Types/Filters ---



Type                     Filter

LSDB                     

Neighbor                 

Policy                   

1.29   show ospf3 interface

show ospf3 interface [if-name] [detail]

1.29.1   Purpose

Displays Open Shortest Path First Version 3 (OSPFv3) interface information.

1.29.2   Command Mode

all modes

1.29.3   Syntax Description

if-name

Optional. Name of a particular interface.

detail

Optional. Displays detailed information.

1.29.4   Default

Displays summary information about all configured OSPFv3 interfaces in the context.

1.29.5   Usage Guidelines

Use the show ospf3 interface command to display OSPFv3 interface information.

Note:  
By default, most show commands (in any mode) display information for the current context only or, depending on the command syntax, for all contexts. If you are an administrator for the local context, you can insert the optional context ctx-name construct, preceding the show command, to view output for the specified context without entering that context. For more information about using the context ctx-name construct, see the context command description.

Note:  
By appending a space followed by the pipe ( | ) character at the end of a show command, you can filter the output using a set of modifier keywords and arguments. For more information, see “Modifying Output of show Commands” in Using the CLI.

1.29.6   Examples

The following example displays output from the show ospf3 interface command:

[local]Redback>show ospf3 interface



  --- OSPFv3 Interfaces for Instance 1/Router ID 2.2.2.2 ---



Name                 NetworkType     Cost    Priority State    Area

lo                   loopback        1       N/A      Loopback 0.0.0.0

to_mer               broadcast       10      1        BDR      0.0.0.0

to_ven               broadcast       1       1        DR       0.0.0.0

1.30   show ospf3 intra-rib

show ospf3 intra-rib instance-id {area-id | ip-addr} [detail]

1.30.1   Purpose

Displays Open Shortest Path First Version 3 (OSPFv3) intra-Routing Information Base (RIB) information.

1.30.2   Command Mode

all modes

1.30.3   Syntax Description

instance-id

OSPFv3 instance ID. The range of values is 1 to 65,535.

area-id

Area ID. The range of values is 0 to 4,294,967,295.

ip-addr

Area IP address in the form A.B.C.D.

detail

Optional. Displays detailed information.

1.30.4   Default

Displays summary information about all configured OSPFv3 intra-RIB information.

1.30.5   Usage Guidelines

Use the show ospf3 intra-rib command to display OSPFv3 intra-RIB information.

Note:  
By default, most show commands (in any mode) display information for the current context only or, depending on the command syntax, for all contexts. If you are an administrator for the local context, you can insert the optional context ctx-name construct, preceding the show command, to view output for the specified context without entering that context. For more information about using the context ctx-name construct, see the context command description.

Note:  
By appending a space followed by the pipe ( | ) character at the end of a show command, you can filter the output using a set of modifier keywords and arguments. For more information, see “Modifying Output of show Commands” in Using the CLI.

1.30.6   Examples

The following example displays output from the show ospf3 intra-rib command:

[local]Redback>show ospf3 intra-rib 1 0

-- Intra Area 0.0.0.0 entries for Instance 1/Router ID 2.2.2.2 --

Destination     Cost  LS-Type LSDB Id         Spf NextHop
2.2.2.2         0     Router  0.0.0.0         0   ::
3.3.3.3         1     Router  0.0.0.0         5   fe80::230:88ff:fe00:3294
4.4.4.4         10    Router  0.0.0.0         5   fe80::2b0:64ff:fe2c:523
2.2.2.2         1     Network 0.0.0.4         5   to_ven
4.4.4.4         11    Network 0.0.0.5         5   fe80::230:88ff:fe00:3294
4.4.4.4         10    Network 0.0.0.6         5   to_mer

1.31   show ospf3 malform

show ospf3 malform

1.31.1   Purpose

Displays Open Shortest Path First Version 3 (OSPFv3) malform log information.

1.31.2   Command Mode

all modes

1.31.3   Syntax Description

This command has no keywords or arguments.

1.31.4   Default

None

1.31.5   Usage Guidelines

Use the show ospf3 malform command to display OSPFv3 malform log information.

Note:  
By default, most show commands (in any mode) display information for the current context only or, depending on the command syntax, for all contexts. If you are an administrator for the local context, you can insert the optional context ctx-name construct, preceding the show command, to view output for the specified context without entering that context. For more information about using the context ctx-name construct, see the context command description.

Note:  
By appending a space followed by the pipe ( | ) character at the end of a show command, you can filter the output using a set of modifier keywords and arguments. For more information, see “Modifying Output of show Commands” in Using the CLI.

1.31.6   Examples

The following example displays output from the show ospf3 malform command:

[local]Redback>show ospf3 malform

OSPF3 malform messages (3 total entries):
Feb 16 10:03:47 Malformed msg Type: DD (nbr fe80::2b0:64ff:fe2c:523, context 0x40080001, 28 bytes, repeated 0 times, reason: 14) - 
 0302 001c 0404 0404 0000 0000 e082 0000 0000 0013 05dc 0007 0000 0bab
Feb 16 10:03:52 Malformed msg Type: LSR (nbr fe80::230:88ff:fe00:3294, context 0x40080001, 40 bytes, repeated 0 times, reason: 7) - 
 0303 0028 0a0c d1a3 0000 0000 562d 0000 0003 2009 0000 0004 0a0c d1a3 8000 2002 0000 0004 0a0c d1a3
Feb 16 10:03:52 Malformed msg Type: DD (nbr fe80::2b0:64ff:fe2c:523, context 0x40080001, 28 bytes, repeated 0 times, reason: 7) - 
 0302 001c 0404 0404 0000 0000 e082 0000 0000 0013 05dc 0007 0000 0bab

1.32   show ospf3 neighbor

show ospf3 neighbor [neighbor-id | interface [ip-addr | if-name]] [detail]

1.32.1   Purpose

Displays Open Shortest Path First Version 3 (OSPFv3) neighbor information.

1.32.2   Command Mode

all modes

1.32.3   Syntax Description

neighbor-id

Optional. ID of the neighbor for which information is displayed.

interface

Optional. Displays information for the specified neighbor interface.

ip-addr

Optional. IP address of the interface.

if-name

Optional. Interface name.

detail

Optional. Displays detailed information.

1.32.4   Default

Displays summary information for all OSPFv3 neighbors.

1.32.5   Usage Guidelines

Use the show ospf3 neighbor command to display OSPFv3 neighbor information.

Note:  
By default, most show commands (in any mode) display information for the current context only or, depending on the command syntax, for all contexts. If you are an administrator for the local context, you can insert the optional context ctx-name construct, preceding the show command, to view output for the specified context without entering that context. For more information about using the context ctx-name construct, see the context command description.

Note:  
By appending a space followed by the pipe ( | ) character at the end of a show command, you can filter the output using a set of modifier keywords and arguments. For more information, see “Modifying Output of show Commands” in Using the CLI.

1.32.6   Examples

The following example displays output from the show ospf3 neighbor command:

[local]Redback>show ospf3 neighbor



  --- OSPFv3 Neighbors for Instance 1/Router ID 2.2.2.2 ---



NeighborID       Pri State    DR-State InterfaceName      TimeLeft

4.4.4.4          1   Full     DR       to_mer             35

3.3.3.3          1   Full     BDR      to_ven             40

1.33   show ospf3 route

show ospf3 route [instance-id] [ipv6-addr [/prefix-length] | external | inter-area | intra-area | redistributed | summary | vpn] [detail]

1.33.1   Purpose

Displays Open Shortest Path First Version 3 (OSPFv3) route information.

1.33.2   Command Mode

all modes

1.33.3   Syntax Description

instance-id

Optional. OSPFv3 instance ID. The range of values is 1 to 65,535.

ipv6-addr

Optional. IP address in the form A:B:C:D:E:E:F:G.

prefix-length

Optional. Prefix length. The range of values is 0 to 32.

external

Optional. Displays all external routes.

inter-area

Optional. Displays all interarea routes.

intra-area

Optional. Displays all intra-area routes.

redistributed

Optional. Displays routes redistributed from other routing protocols.

summary

Optional. Displays route summary information.

vpn

Optional. Displays redistributed Virtual Private Network (VPN) routes. This option is only available in a VPN context.

detail

Optional. Displays detailed route information.

1.33.4   Default

Displays basic route information for all instances.

1.33.5   Usage Guidelines

Use the show ospf3 route command to display OSPFv3 route information.

Note:  
By default, most show commands (in any mode) display information for the current context only or, depending on the command syntax, for all contexts. If you are an administrator for the local context, you can insert the optional context ctx-name construct, preceding the show command, to view output for the specified context without entering that context. For more information about using the context ctx-name construct, see the context command description.

Note:  
By appending a space followed by the pipe ( | ) character at the end of a show command, you can filter the output using a set of modifier keywords and arguments. For more information, see “Modifying Output of show Commands” in Using the CLI.

1.33.6   Examples

The following example displays a summary of all OSPFv3 routes:

[local]Redback>show ospf3 route

       --- OSPFv3 Routes for Instance 1/Router ID 2.2.2.2 ---

Destination                              Type       Dest-Type/Proto   Cost  #hop
2005::/112                               Intra      Net               1     1  
  Nexthop: to_ven           
2006::/112                               Intra      Net               10    1  
  Nexthop: to_mer           
2007::/112                               Intra      Net               11    1  
  Nexthop: fe80::230:88ff:fe00:3294
4001::2/128                              Intra      Net               0     1  
  Nexthop: lo               
4001::3/128                              Intra      Net               2     1  
  Nexthop: fe80::230:88ff:fe00:3294
6001::/48                                EXT T2     Net               0     1  
  Nexthop: fe80::230:88ff:fe00:3294
6002::/64                                EXT T2     Net               0     1  
  Nexthop: fe80::230:88ff:fe00:3294

1.34   show ospf3 spf

show ospf3 spf [instance-id] [last | log | scheduling] [timestamp]

1.34.1   Purpose

Displays Open Shortest Path First Version 3 (OSPFv3) Shortest Path First (SPF) calculation statistics.

1.34.2   Command Mode

all modes

1.34.3   Syntax Description

instance-id

OSPFv3 instance ID. Displays SPF information only for the specified instance.

last

Optional. Displays the most recent SPF route calculation.

log

Optional. Displays the SPF calculation timing log.

scheduling

Optional. Displays the SPF route calculation scheduling log.

timestamp

Optional. Displays the SPF timestamp.

1.34.4   Default

Displays SPF information for all configured instances of OSPFv3.

1.34.5   Usage Guidelines

Use the show ospf3 spf command to display OSPFv3 SPF calculation statistics.

Note:  
By default, most show commands (in any mode) display information for the current context only or, depending on the command syntax, for all contexts. If you are an administrator for the local context, you can insert the optional context ctx-name construct, preceding the show command, to view output for the specified context without entering that context. For more information about using the context ctx-name construct, see the context command description.

Note:  
By appending a space followed by the pipe ( | ) character at the end of a show command, you can filter the output using a set of modifier keywords and arguments. For more information, see “Modifying Output of show Commands” in Using the CLI.

1.34.6   Examples

The following example displays all SPF information for all OSPFv3 instances:

[local]Redback>show ospf3 spf



   --- OSPFv3 SPF Route Calculation Timing Log  ---



     Maximum SPF-Phase Timings

When (elapsed)  Instance/Area         Phase     Duration

00:10:19        1/N/A                 Init      < 1 ms

00:18:48        1/0.0.0.0             Intra     2 ms

00:18:48        1/0.0.0.0             Inter     1 ms

00:10:19        1/N/A                 External  1 ms

00:16:25        1/N/A                 Post      1 ms



     Most Recent SPF-Phase Timings

When (elapsed)  Instance/Area         Phase     Duration

00:10:19        1/N/A                 Init      < 1 ms

00:10:19        1/0.0.0.0             Intra     < 1 ms

00:10:19        1/0.0.0.0             Inter     < 1 ms

00:10:19        1/N/A                 External  1 ms

00:10:19        1/N/A                 Post      < 1 ms

00:16:10        1/N/A                 Init      < 1 ms

00:16:10        1/0.0.0.0             Intra     1 ms

00:16:10        1/0.0.0.0             Inter     < 1 ms

00:16:10        1/N/A                 External  < 1 ms

00:16:10        1/N/A                 Post      < 1 ms

00:16:25        1/N/A                 Init      < 1 ms

00:16:25        1/0.0.0.0             Intra     < 1 ms

00:16:25        1/0.0.0.0             Inter     < 1 ms

00:16:25        1/N/A                 External  < 1 ms

00:16:25        1/N/A                 Post      1 ms

00:16:37        1/N/A                 Init      < 1 ms

00:16:37        1/0.0.0.0             Intra     < 1 ms

00:16:37        1/0.0.0.0             Inter     < 1 ms

00:16:37        1/N/A                 External  < 1 ms

00:16:37        1/N/A                 Post      1 ms

00:18:48        1/N/A                 Init      < 1 ms

00:18:48        1/0.0.0.0             Intra     2 ms

00:18:48        1/0.0.0.0             Inter     1 ms

00:18:48        1/N/A                 External  < 1 ms

00:18:48        1/N/A                 Post      1 ms

1.35   show ospf3 statistics

show ospf3 statistics [instance-id] [interface [if-name] [detail]] [neighbor [ip-addr | interface if-name]] [packet-io] [scheduler [detail]]

1.35.1   Purpose

Displays Open Shortest Path First Version 3 (OSPFv3) statistics.

1.35.2   Command Mode

all modes

1.35.3   Syntax Description

instance-id

Optional. Instance ID. The range of values is 1 to 65,535.

interface if-name

Optional. Interface name. Displays OSPFv3 statistics for the specified interface. When used with neighbor keyword, displays OSPFv3 statistics for all neighbors on the specified interface.

detail

Optional. Displays detailed statistics.

neighbor

Optional. Displays neighbor statistics.

ip-addr

Optional. IP address of the neighbor interface for which OSPFv3 statistics are displayed.

packet-io

Optional. Displays packet I/O statistics.

scheduler

Optional. Displays scheduler statistics.

1.35.4   Default

None

1.35.5   Usage Guidelines

Use the show ospf3 statistics command to display OSPFv3 statistics.

Note:  
By default, most show commands (in any mode) display information for the current context only or, depending on the command syntax, for all contexts. If you are an administrator for the local context, you can insert the optional context ctx-name construct, preceding the show command, to view output for the specified context without entering that context. For more information about using the context ctx-name construct, see the context command description.

Note:  
By appending a space followed by the pipe ( | ) character at the end of a show command, you can filter the output using a set of modifier keywords and arguments. For more information, see “Modifying Output of show Commands” in Using the CLI.

1.35.6   Examples

The following example displays statistics for all configured OSPFv3 interfaces and neighbors:

[local]Redback>show ospf3 statistics



  --- OSPFv3 Statistics for Instance 1 ---



Max flood queue length   : 2           Interval            : 00:19:34

LSAs received            : 95          LSAs sent           : 104  

LSAs changes received    : 58          LSA Retransmissions : 6    

Packet Retransmissions   : 3           RIB initializations : 1    

Routes downloaded        : 14          Routes deleted      : 1    

Download Errors          : 0           RIB IPC messages    : 5    

Download SPF Delays      : 0           SPF Download Delays : 0    

DC Indicate originated   : 0           DC Indicate purged  : 0    

DC DoNotAge purged       : 0         



              Hello    DD       LSR      LSU      ACK

        Sent  241      21       8        42       23      

        Recv  239      17       7        41       19      

1.36   show ospf3 summary-address

show ospf3 summary-address [instance-id]

1.36.1   Purpose

Displays Open Shortest Path First Version 3 (OSPFv3) summary address information.

1.36.2   Command Mode

all modes

1.36.3   Syntax Description

instance-id

Optional. OSPFv3 instance ID. The range of values is 1 to 65,535.

1.36.4   Default

None

1.36.5   Usage Guidelines

Use the show ospf3 summary-address command to display OSPFv3 summary address information.

Note:  
By default, most show commands (in any mode) display information for the current context only or, depending on the command syntax, for all contexts. If you are an administrator for the local context, you can insert the optional context ctx-name construct, preceding the show command, to view output for the specified context without entering that context. For more information about using the context ctx-name construct, see the context command description.

Note:  
By appending a space followed by the pipe ( | ) character at the end of a show command, you can filter the output using a set of modifier keywords and arguments. For more information, see “Modifying Output of show Commands” in Using the CLI.

1.36.6   Examples

The following example displays OSPFv3 summary address information:

[local]Redback>show ospf3 summary-address



  --- OSPFv3 Summaries for Instance 1/Router ID 3.3.3.3 ---



Prefix          Length Tag        Type          Status   Metric

7000::          110    0x0        advertise     inactive

1.37   show ospf area

show ospf area [instance-id] [area-id [ip-addr]] [brief]

1.37.1   Purpose

Displays information about Open Shortest Path First (OSPF) areas.

1.37.2   Command Mode

all modes

1.37.3   Syntax Description

instance-id

Optional. Instance ID. The range of values is 1 to 65,535.

area-id

Optional. Area ID. The range of values is 0 to 4,294,967,295.

ip-addr

Optional. IP address.

brief

Optional. Provides a summary of information.

1.37.4   Default

Displays summary information for all OSPF areas.

1.37.5   Usage Guidelines

Use the show ospf area command to display information about OSPF areas.

Note:  
By default, most show commands (in any mode) display information for the current context only or, depending on the command syntax, for all contexts. If you are an administrator for the local context, you can insert the optional context ctx-name construct, preceding the show command, to view output for the specified context without entering that context. For more information about using the context ctx-name construct, see the context command description.

Note:  
By appending a space followed by the pipe ( | ) character at the end of a show command, you can filter the output using a set of modifier keywords and arguments. For more information, see “Modifying Output of show Commands” in Using the CLI.

1.37.6   Examples

The following example displays output from the show ospf area command:

[local]Redback>show ospf area 
--- OSPF Area 0.0.0.0 Instance 1/Router ID 193.10.25.7 ---



Area Type      : Transit           Interface Count: 2

SPF Count      : 12                Virtual Nbr    : 0

LSA Count      : 15                LSA Checksum   : 0x095e76

ABR Count      : 2                 ASBR Count     : 1

Interface List:

193.4.5.2        193.10.25.7



  --- OSPF Area 0.0.0.1 Instance 1/Router ID 193.10.25.7 ---



Area Type      : Transit           Interface Count: 2

SPF Count      : 12                Virtual Nbr    : 0

LSA Count      : 16                LSA Checksum   : 0x083b1d

ABR Count      : 2                 ASBR Count     : 1



Interface List:

10.1.1.1       10.3.1.1

The following example displays output from the show ospf area 0.0.0.1 command. The area type for area 0.0.0.1 is transit. The OSPF-enabled interface IP addresses are 10.1.1.1 and 10.3.1.1, and the number of Shortest Path First (SPF) calculations performed is 12:

[local]Redback>show ospf area 0.0.0.1
--- OSPF Area 0.0.0.0 Instance 1/Router ID 193.10.25.7 ---



Area Type      : Regular           Interface Count: 1

LSA Count      : 1                 LSA Checksum   : 0x0a40d

ABR Count      : 0                 ASBR Count     : 0

Adjacent Nbrs  : 0                 Up Interfaces  : 1



Interface List:

193.4.5.2

The following example displays output from the show ospf area brief command:

[local]Redback>show ospf area brief
--- OSPF Areas for Instance 1/Router ID 193.10.25.7 ---



Area           Type       Intf-Count      LSA-Count   LSA cksum

0.0.0.0        Regular    1               3           0x00026314

0.0.0.1        Regular    2               2           0x00007d78

1.38   show ospf border-routers

show ospf border-routers [instance-id] [abr | all | asbr] [detail]

1.38.1   Purpose

Displays routes to area border routers (ABRs), autonomous system boundary routers (ASBRs), and other Open Shortest Path First (OSPF) routers.

1.38.2   Command Mode

all modes

1.38.3   Syntax Description

instance-id

Optional. Instance ID. The range of values is 1 to 65,535.

abr

Optional. Lists information about ABRs.

all

Optional. Lists information about ABRs, ASBRs, and other OSPF routers.

asbr

Optional. Lists information about ASBRs.

detail

Optional. Displays detailed information.

1.38.4   Default

None

1.38.5   Usage Guidelines

Use the show ospf border-routers command to display routes to ABRs, ASBRs, and other OSPF routers.

Note:  
By default, most show commands (in any mode) display information for the current context only or, depending on the command syntax, for all contexts. If you are an administrator for the local context, you can insert the optional context ctx-name construct, preceding the show command, to view output for the specified context without entering that context. For more information about using the context ctx-name construct, see the context command description.

Note:  
By appending a space followed by the pipe ( | ) character at the end of a show command, you can filter the output using a set of modifier keywords and arguments. For more information, see “Modifying Output of show Commands” in Using the CLI.

1.38.6   Examples

The following example indicates that there is a route to an ABR at IP address 33.33.33.33. The next-hop IP address is 193.4.4.1 and the route cost is 11:

[local]Redback>show ospf border-routers abr
--- Border Routers for OSPF Instance 1/Router ID 193.10.25.7 ---



Destination     Next Hop(s)     Cost    Type   Route-Type  Area

33.33.33.33      193.4.4.1      11      ABR    Intra       0.0.0.0

33.33.33.33      10.3.2.2       1       ABR    Intra       0.0.0.1

The following example indicates that there is a route to an ASBR at IP address 22.22.22.22. The next-hop IP address is 10.1.2.2 and the route cost is 1:

[local]Redback>show ospf border-router asbr
--- Border Routers for OSPF Instance 1/Router ID 193.10.25.7 ---



Destination    Next Hop(s)      Cost    Type     Route-Type  Area

19.4.123.89    193.4.4.1        1       ASBR     Intra       0.0.0.0

22.22.22.22    10.1.2.2         1       ASBR     Intra       0.0.0.1

The following example provides detailed information about all ABRs, ASBRs, and other routers:

[local]Redback>show ospf border-routers detail
--- Border Routers for OSPF Instance 1/Router ID 193.10.25.7 ---



Destination    : 19.4.123.89          Type           : Intra 

Dest-type      : ASBR                 Cost           : 1 

Area           : 0.0.0.0              Back Link Data : 193.4.4.1 

LSDB Type      : Rtr                  LSDB ID        : 19.4.123.89 

LSDB Adv Router: 19.4.123.89          Next Hop Count : 1 

SPF Count      : 12

Next Hops      : 193.4.4.1

Route Flags    : changed



Destination    : 33.33.33.33          Type           : Intra

Dest-type      : ABR                  Cost           : 11

Area           : 0.0.0.0              Back Link Data : 20.1.1.1

LSDB Type      : Rtr                  LSDB ID        : 33.33.33.33

LSDB Adv Router: 33.33.33.33          Next Hop Count : 1

SPF Count      : 12

Next Hops      : 193.4.4.1

Route Flags    : changed



Destination    : 22.22.22.22          Type           : Intra

Dest-type      : ASBR                 Cost           : 1 

Area           : 0.0.0.1              Back Link Data : 10.1.2.2 

LSDB Type      : Rtr                  LSDB ID        : 22.22.22.22 

LSDB Adv Router: 22.22.22.22          Next Hop Count : 1 

SPF Count      : 12 

Next Hops      : 10.1.2.2 

Route Flags    : changed



Destination    : 33.33.33.33          Type           : Intra 

Dest-type      : ABR                  Cost           : 1 

Area           : 0.0.0.1              Back Link Data : 10.3.2.2 

LSDB Type      : Rtr                  LSDB ID        : 33.33.33.33 

LSDB Adv Router: 33.33.33.33          Next Hop Count : 1 

SPF Count      : 12 

Next Hops      : 10.3.2.2 

Route Flags    : changed

1.39   show ospf database

show ospf database [instance-id] [area-id | ip-addr]

1.39.1   Purpose

Displays information stored in the Open Shortest Path First (OSPF) link-state database (LSDB).

1.39.2   Command Mode

all modes

1.39.3   Syntax Description

instance-id

Optional. OSPF instance ID. The range of values is 1 to 65,535.

area-id

Optional. Area ID. The range of values is 0 to 4,294,967,295.

ip-addr

Optional. Area IP address.

1.39.4   Default

None

1.39.5   Usage Guidelines

Use the show ospf database command to display information stored in the OSPF LSDB.

Note:  
By default, most show commands (in any mode) display information for the current context only or, depending on the command syntax, for all contexts. If you are an administrator for the local context, you can insert the optional context ctx-name construct, preceding the show command, to view output for the specified context without entering that context. For more information about using the context ctx-name construct, see the context command description.

Note:  
By appending a space followed by the pipe ( | ) character at the end of a show command, you can filter the output using a set of modifier keywords and arguments. For more information, see “Modifying Output of show Commands” in Using the CLI.

1.39.6   Examples

The following example provides information about link-state advertisement (LSA) type, link ID, advertising router IP address, link-state age, checksums, and sequence number:

[local]Redback>show ospf database 
--- OSPF Link State Database for Instance 1/Router ID 193.10.25.7 ---



    Router Link State Advertisements (Area 0.0.0.0)

LinkID         AdvertisingRtr   Sequence #  ChkSm  Option Length LSAge

19.4.123.89    19.4.123.89      80000fe5    a3dc   E,DC   60     146 

33.33.33.33    33.33.33.33      80000006    a66e   E      36     165 

111.11.11.11   111.11.11.11     80000042    83b7   E      60     603 

193.10.25.7    193.10.25.7      80000006    ffe0   E      48     145 



    Network Link State Advertisements (Area 0.0.0.0)

LinkID         AdvertisingRtr   Sequence #  ChkSm  Option Length LSAge

20.1.1.2       19.4.123.89      80000001    1ea7   E,DC   32     164 

193.4.4.1      19.4.123.89      80000001    d9e    E,DC   32     146 



    Summary Network Link State Advertisements (Area 0.0.0.0)

LinkID         AdvertisingRtr   Sequence #  ChkSm  Option Length LSAge

10.1.0.0       33.33.33.33      80000001    fbc    E      28     126 

10.1.0.0       111.11.11.11     8000002a    c1d5   E      28     453 

10.1.0.0       193.10.25.7      80000001    ec78   E      28     184 

10.2.0.0       33.33.33.33      80000001    f8d2   E      28     176 

10.2.0.0       193.10.25.7      80000001    ea78   E      28     137 

10.3.0.0       33.33.33.33      80000001    ecdd   E      28     176 

10.3.0.0       193.10.25.7      80000001    d48e   E      28     184 



    Summary AS Border Router Link State Advertisements (Area 0.0.0.0)

LinkID         AdvertisingRtr   Sequence #  ChkSm  Option Length LSAge

22.22.22.22    33.33.33.33      80000002    8bf1   E      28     99

22.22.22.22    193.10.25.7      80000001    75a1   E      28     137



    Router Link State Advertisements (Area 0.0.0.1)

LinkID         AdvertisingRtr   Sequence #  ChkSm  Option Length LSAge

22.22.22.22    22.22.22.22      8000000c    3b10   E      48     102 

33.33.33.33    33.33.33.33      8000000c    4ca1   E      48     101 

193.10.25.7    193.10.25.7      80000008    111a   E      48     130 



    Network Link State Advertisements (Area 0.0.0.1)

LinkID         AdvertisingRtr   Sequence #  ChkSm  Option Length LSAge

10.1.1.1       193.10.25.7      80000001    f824   E      32     143 

10.2.2.2       33.33.33.33      80000001    9157   E      32     101 

10.3.1.1       193.10.25.7      80000001    9e5    E      32     130 



    Summary Network Link State Advertisements (Area 0.0.0.1)

LinkID         AdvertisingRtr   Sequence #  ChkSm  Option Length LSAge

19.4.123.89    33.33.33.33      80000001    a941   E      28     158 

19.4.123.89    193.10.25.7      80000001    91f1   E      28     139 

20.1.1.0       33.33.33.33      80000001    774a   E      28     175 

20.1.1.0       193.10.25.7      80000001    c38c   E      28     139 

193.4.0.0      33.33.33.33      80000001    f017   E      28     158 

193.4.0.0      193.10.25.7      80000001    7436   E      28     184 

193.10.25.7    33.33.33.33      80000001    5888   E      28     135 

193.10.25.7    193.10.25.7      80000001    1b2    E      28     185 



    Summary AS Border Router Link State Advertisements (Area 0.0.0.1)

LinkID         AdvertisingRtr   Sequence #  ChkSm  Option Length LSAge

19.4.123.89    33.33.33.33      80000001    9159   E      28     158 

19.4.123.89    193.10.25.7      80000001    790a   E      28     139 



    External Link State Advertisements

LinkID         AdvertisingRtr   Sequence #  ChkSm  Option Length LSAge

7.0.0.0        19.4.123.89      8000002b    f38f   DC     36     242 

8.0.0.0        19.4.123.89      8000002b    e69b   DC     36     242 

9.9.9.0        19.4.123.89      8000002b    a65    DC     36     242 

25.1.1.0       22.22.22.22      80000001    ee70   E      36     141 

26.0.0.0       22.22.22.22      80000001    f867   E      36     141 

27.1.0.0       22.22.22.22      80000001    df7e   E      36     141 

28.1.1.0       22.22.22.22      80000001    c794   E      36     131 

30.0.0.0       22.22.22.22      80000001    ef96   E      36     131 

1.40   show ospf database advertising router

show ospf database [instance-id] [area-id | ip-addr] advertising router {router-id | self-originate} [detail]

1.40.1   Purpose

Displays information about Open Shortest Path First (OSPF) advertising router link-state advertisements (LSAs).

1.40.2   Command Mode

all modes

1.40.3   Syntax Description

instance-id

Optional. OSPF instance ID. The range of values is 1 to 65,535.

area-id

Optional. Area ID. The range of values is 0 to 4,294,967,295.

ip-addr

Optional. Area IP address.

router-id

OSPF router ID in the form A.B.C.D.

self-originate

Displays self-originated LSAs.

detail

Optional. Provides detailed information.

1.40.4   Default

None

1.40.5   Usage Guidelines

Use the show ospf database advertising router command to display information about OSPF advertising router LSAs.

Note:  
By default, most show commands (in any mode) display information for the current context only or, depending on the command syntax, for all contexts. If you are an administrator for the local context, you can insert the optional context ctx-name construct, preceding the show command, to view output for the specified context without entering that context. For more information about using the context ctx-name construct, see the context command description.

Note:  
By appending a space followed by the pipe ( | ) character at the end of a show command, you can filter the output using a set of modifier keywords and arguments. For more information, see “Modifying Output of show Commands” in Using the CLI.

1.40.6   Examples

The following example provides information specific to the advertising router, 192.10.25.7:

[local]Redback>show ospf database 1 0.0.0.1 advertising-router 192.10.25.7
--- OSPF Link State Database for Instance 1/Router ID 193.10.25.7 ---

                        Router Link State Advertisements (Area 0.0.0.1)
LinkID           AdvertisingRtr   Sequence # ChkSm  Option Length LSAge
22.22.22.22      22.22.22.22      8000000c   3b10   E      48     188 
33.33.33.33      33.33.33.33      8000000c   4ca1   E      48     187 
193.10.25.7      193.10.25.7      80000008   111a   E      48     216 

                       Network Link State Advertisements (Area 0.0.0.1)
LinkID           AdvertisingRtr   Sequence # ChkSm  Option Length LSAge
10.1.1.1         193.10.25.7      80000001   f824   E      32     229 
10.2.2.2         33.33.33.33      80000001   9157   E      32     187 
10.3.1.1         193.10.25.7      80000001   9e5    E      32     216 

                      Summary Network Link State Advertisements (Area 0.0.0.1)
LinkID           AdvertisingRtr   Sequence #  ChkSm  Option Length LSAge
19.4.123.89      33.33.33.33      80000001    a941   E      28     244 
19.4.123.89      193.10.25.7      80000001    91f1   E      28     225 
20.1.1.0         33.33.33.33      80000001    774a   E      28     261 
20.1.1.0         193.10.25.7      80000001    c38c   E      28     225 
193.4.0.0        33.33.33.33      80000001    f017   E      28     244 
193.4.0.0        193.10.25.7      80000001    7436   E      28     270 
193.10.25.7      33.33.33.33      80000001    5888   E      28     221 
193.10.25.7      193.10.25.7      80000001    d1b2   E      28     271 

                     Summary AS Border Router Link State Advertisements (Area 0.0.0.1)
LinkID           AdvertisingRtr   Sequence #  ChkSm  Option Length LSAge
19.4.123.89      33.33.33.33      80000001    9159   E      28     244 
19.4.123.89      193.10.25.7      80000001    790a   E      28     225 

1.41   show ospf database area-scope-opaque

show ospf database [instance-id] [area-id | ip-addr] area-scope-opaque [all | link-id] [self-originate] [detail]

1.41.1   Purpose

Displays information about Open Shortest Path First (OSPF) opaque Type 10 link-state advertisements (LSAs).

1.41.2   Command Mode

all modes

1.41.3   Syntax Description

instance-id

Optional. OSPF instance ID. The range of values is 1 to 65,535.

area-id

Optional. Area ID. The range of values is 0 to 4,294,967,295.

ip-addr

Optional. Area IP address.

all

Optional. Displays all opaque Type 10 LSAs.

link-id

Optional. LSA ID in the form A.B.C.D.

self-originate

Optional. Displays self-originated LSAs.

detail

Optional. Provides detailed information.

1.41.4   Default

None

1.41.5   Usage Guidelines

Use the show ospf database area-scope-opaque command to display information about OSPF opaque Type 10 LSAs. Opaque Type 10 LSAs are not flooded beyond the borders of their associated area.

Note:  
By default, most show commands (in any mode) display information for the current context only or, depending on the command syntax, for all contexts. If you are an administrator for the local context, you can insert the optional context ctx-name construct, preceding the show command, to view output for the specified context without entering that context. For more information about using the context ctx-name construct, see the context command description.

Note:  
By appending a space followed by the pipe ( | ) character at the end of a show command, you can filter the output using a set of modifier keywords and arguments. For more information, see “Modifying Output of show Commands” in Using the CLI.

1.41.6   Examples

The following example displays summary OSPF area scope opaque (Type 10) LSA information:

[local]Redback>show ospf database area-scope-opaque
   --- OSPF Link State Database for Instance 1/Router ID 10.1.2.2 ---



             Area scope Opaque Link State Advertisements (Area 0.0.0.1)

LinkID          AdvertisingRtr   Sequence #  ChkSm  Option Length LSAge

1.0.0.0         10.1.2.2         80000001    4ca5   E,O    28     13

1.0.0.1         10.1.2.2         80000001    5e6e   E,O    116    13

The following example displays detailed OSPF area-scope-opaque (Type 10) LSA information:

[local]Redback>show ospf database area-scope-opaque detail
  --- OSPF Link State Database for Instance 1/Router ID 10.1.2.2 ---



        --- Area scope Opaque LSA 1.0.0.0 (Area 0.0.0.1) ---



Link State Id     : 1.0.0.0            Advertising Router   : 10.1.2.2

Sequence Number   : 0x80000001         Checksum             : 0x4ca5

Options           : E,O                Length               : 28



TLV Type:         : Router             TLV Length:          : 4

Router ID         : 10.1.2.2



        --- Area scope Opaque LSA 1.0.0.1 (Area 0.0.0.1) ---



Link State Id     : 1.0.0.1            Advertising Router   : 10.1.2.2

Sequence Number   : 0x80000001         Checksum             : 0x5e6e

Options           : E,O                Length               : 116



TLV Type:         : Link               TLV Length:          : 92



Sub-TLV Type:     : Link-Type          Sub-TLV Length:      : 1

Link Type         : Multi-access



Sub-TLV Type:     : Link-ID            Sub-TLV Length:      : 4

IP Address(es)    : 10.1.1.1



Sub-TLV Type:     : Local-Address      Sub-TLV Length:      : 4

IP Address(es)    : 10.1.2.2



Sub-TLV Type:     : TE Metric          Sub-TLV Length:      : 4

Metric Value      : 1



Sub-TLV Type:     : Max Bandwidth      Sub-TLV Length:      : 4

Bytes/Second      : 12500000.000000 / Hex: 0x4b3ebc20



Sub-TLV Type:     : Max Reserved BW    Sub-TLV Length:      : 4

Bytes/Second      : 12500000.000000 / Hex: 0x4b3ebc20



Sub-TLV Type:     : Unreserved BW      Sub-TLV Length:      : 32

P[0] Bytes/Second : 12500000.000000 / Hex: 0x4b3ebc20

P[1] Bytes/Second : 12500000.000000 / Hex: 0x4b3ebc20

P[2] Bytes/Second : 12500000.000000 / Hex: 0x4b3ebc20

P[3] Bytes/Second : 12500000.000000 / Hex: 0x4b3ebc20

P[4] Bytes/Second : 12500000.000000 / Hex: 0x4b3ebc20

P[5] Bytes/Second : 12500000.000000 / Hex: 0x4b3ebc20

P[6] Bytes/Second : 12500000.000000 / Hex: 0x4b3ebc20



P[7] Bytes/Second : 12500000.000000 / Hex: 0x4b3ebc20



Sub-TLV Type:     : Class/Color        Sub-TLV Length:      : 4

Class/Color       : 0x00000000

1.42   show ospf database as-scope-opaque

show ospf database [instance-id] [area-id | ip-addr] as-scope-opaque [all | link-id] [self-originate] [detail]

1.42.1   Purpose

Displays information about Open Shortest Path First (OSPF) opaque Type 11 link-state advertisements (LSAs).

1.42.2   Command Mode

all modes

1.42.3   Syntax Description

instance-id

Optional. OSPF instance ID. The range of values is 1 to 65,535.

area-id

Optional. Area ID. The range of values is 0 to 4,294,967,295.

ip-addr

Optional. Area IP address.

all

Optional. Displays all opaque Type 11 LSAs.

link-id

Optional. LSA ID in the form A.B.C.D.

self-originate

Optional. Displays self-originated LSAs.

detail

Optional. Provides detailed information.

1.42.4   Default

None

1.42.5   Usage Guidelines

Use the show ospf database as-scope-opaque command to display information about OSPF opaque Type 10 LSAs. Opaque Type 11 LSAs are not flooded beyond the borders of their associated autonomous system (AS).

Note:  
By default, most show commands (in any mode) display information for the current context only or, depending on the command syntax, for all contexts. If you are an administrator for the local context, you can insert the optional context ctx-name construct, preceding the show command, to view output for the specified context without entering that context. For more information about using the context ctx-name construct, see the context command description.

Note:  
By appending a space followed by the pipe ( | ) character at the end of a show command, you can filter the output using a set of modifier keywords and arguments. For more information, see “Modifying Output of show Commands” in Using the CLI.

1.42.6   Examples

The following example displays summary OSPF AS scope opaque (Type 11) LSA information:

[local]Redback>show ospf database as-scope-opaque
  --- OSPF Link State Database for Instance 1/Router ID 193.10.25.7 ---



           AS scope Opaque Link State Advertisements (Area 0.0.0.1)

LinkID         AdvertisingRtr   Sequence #  ChkSm  Option  Length LSAge

4.0.0.0        193.10.25.7      80000001    c5a    E,DC,O  36     6

The following example displays detailed OSPF AS scope opaque (Type 11) LSA information:

[local]Redback>show ospf database as-scope-opaque detail
  --- OSPF Link State Database for Instance 1/Router ID 193.10.25.7 ---



        --- AS scope Opaque LSA 4.0.0.0 (Area 0.0.0.1) ---



Link State Id     : 4.0.0.0           Advertising Router  : 193.10.25.7

Sequence Number   : 0x80000001        Checksum            : 0xc5a

Options           : E,DC,O            Length              : 36



TLV Type:         : Capabilities      TLV Length:         : 12



Sub-TLV Type:     : Capability Bits   Sub-TLV Length:     : 4

Graceful Restart  : No                Graceful Helper     : Yes

Stub Router       : No                P2P over LAN        : Yes

MPLS TE           : No                MPLS TE PCS         : No

1.43   show ospf database database-summary

show ospf database [instance-id] [area-id | ip-addr] database-summary

1.43.1   Purpose

Displays a count, grouped by type, of Open Shortest Path First (OSPF) link-state advertisements (LSAs).

1.43.2   Command Mode

all modes

1.43.3   Syntax Description

instance-id

Optional. OSPF instance ID. The range of values is 1 to 65,535.

area-id

Optional. Area ID. The range of values is 0 to 4,294,967,295.

ip-addr

Optional. Area IP address.

1.43.4   Default

None

1.43.5   Usage Guidelines

Use the show ospf database database-summary command to display a count, grouped by type, of OSPF LSAs.

Note:  
By default, most show commands (in any mode) display information for the current context only or, depending on the command syntax, for all contexts. If you are an administrator for the local context, you can insert the optional context ctx-name construct, preceding the show command, to view output for the specified context without entering that context. For more information about using the context ctx-name construct, see the context command description.

Note:  
By appending a space followed by the pipe ( | ) character at the end of a show command, you can filter the output using a set of modifier keywords and arguments. For more information, see “Modifying Output of show Commands” in Using the CLI.

1.43.6   Examples

The following example displays a summary of database information:

[local]Redback>show ospf database database-summary
--- OSPF Database Summary for Instance 1/Router ID 193.10.25.7 ---



Area ID          Router       Network      Sum-Net   Sum-ASBR   NSSA

0.0.0.0          1            0            2         0          0

                 Opaque-Area  Opaque-Link  Deleted   MaxAge

                 0            0            0         0



Area ID          Router       Network      Sum-Net   Sum-ASBR   NSSA

0.0.0.1          1            0            1         0          0

                 Opaque-Area  Opaque-Link  Deleted   MaxAge

                 0            0            0         0



Instance         AS External

                 0

1.44   show ospf database external

show ospf database [instance-id] [area-id | ip-addr] external [all | link-id] [router-id | self-originate]] [detail]

1.44.1   Purpose

Displays information about Open Shortest Path First (OSPF) Type 5 autonomous system (AS) external link-state advertisements (LSAs).

1.44.2   Command Mode

all modes

1.44.3   Syntax Description

instance-id

Optional. OSPF instance ID. The range of values is 1 to 65,535.

area-id

Optional. Area ID. The range of values is 0 to 4,294,967,295.

ip-addr

Optional. Area IP address.

all

Optional. Displays all Type 5 AS external LSAs.

link-id

Optional. LSA ID in the form A.B.C.D.

router-id

Optional. OSPF router ID in the form A.B.C.D.

self-originate

Optional. Displays self-originated LSAs.

detail

Optional. Provides detailed information.

1.44.4   Default

None

1.44.5   Usage Guidelines

Use the show ospf database external command to display information about OSPF Type 5 AS external LSAs.

Note:  
By default, most show commands (in any mode) display information for the current context only or, depending on the command syntax, for all contexts. If you are an administrator for the local context, you can insert the optional context ctx-name construct, preceding the show command, to view output for the specified context without entering that context. For more information about using the context ctx-name construct, see the context command description.

Note:  
By appending a space followed by the pipe ( | ) character at the end of a show command, you can filter the output using a set of modifier keywords and arguments. For more information, see “Modifying Output of show Commands” in Using the CLI.

1.44.6   Examples

The following example displays output from the show ospf database external command:

[local]Redback>show ospf database external
  --- OSPF Link State Database for Instance 1/Router ID 193.10.25.7 ---

 

             External Link State Advertisements

LinkID          AdvertisingRtr   Sequence #  ChkSm  Option Length LSAge

7.0.0.0         19.4.123.89      80000001    4865   DC     36     186

8.0.0.0         19.4.123.89      80000001    3b71   DC     36     186

9.9.9.0         19.4.123.89      80000001    5e3b   DC     36     185

10.1.0.0        19.4.123.89      80000001    1594   DC     36     28

1.45   show ospf database interface

show ospf database [instance-id] [area-id | ip-addr] interface {ip-addr | if-name} [detail]

1.45.1   Purpose

Displays information about an Open Shortest Path First (OSPF) interface link-state database (LSDB).

1.45.2   Command Mode

all modes

1.45.3   Syntax Description

instance-id

Optional. OSPF instance ID. The range of values is 1 to 65,535.

area-id

Optional. Area ID. The range of values is 0 to 4,294,967,295.

ip-addr

Optional. Area IP address.

interfaceip-addr

Optional. IP address of the OSPF interface.

interface if-name

Optional. Name of the OSPF interface.

detail

Optional. Provides detailed information.

1.45.4   Default

None

1.45.5   Usage Guidelines

Use the show ospf database interface command to display information about an OSPF interface LSDB.

Note:  
By default, most show commands (in any mode) display information for the current context only or, depending on the command syntax, for all contexts. If you are an administrator for the local context, you can insert the optional context ctx-name construct, preceding the show command, to view output for the specified context without entering that context. For more information about using the context ctx-name construct, see the context command description.

Note:  
By appending a space followed by the pipe ( | ) character at the end of a show command, you can filter the output using a set of modifier keywords and arguments. For more information, see “Modifying Output of show Commands” in Using the CLI.

1.45.6   Examples

The following example displays summary OSPF interface LSDB information for the interface, two:

[local]Redback>show ospf database interface two
       Link scope Opaque Link State Advertisements (Interface 10.1.1.1)

LinkID          AdvertisingRtr   Sequence #  ChkSm  Option Length LSAge

3.0.0.0         10.1.2.2         80000001    9d11   E,O    44     4

The following example displays detailed OSPF interface LSDB information:

[local]Redback>show ospf database interface two detail
         --- Link scope Opaque LSA 3.0.0.0 (Interface 10.1.1.1) ---



Link State Id     : 3.0.0.0            Advertising Router   : 10.1.2.2

Sequence Number   : 0x80000001         Checksum             : 0x9d11

Options           : E,O                Length               : 44



TLV Type:         : Grace Period       TLV Length:          : 4

Restart Period    : 40



TLV Type:         : Restart Reason     TLV Length:          : 1

Restart Reason    : Unknown



TLV Type:         : Interface Addr     TLV Length:          : 4

Interface Address : 10.1.2.2

1.46   show ospf database link-scope-opaque

show ospf database [instance-id] [area-id | ip-addr] link-scope-opaque [all | link-id] [self-originate] [detail]

1.46.1   Purpose

Displays information about Open Shortest Path First (OSPF) opaque Type 9 link-state advertisements (LSAs).

1.46.2   Command Mode

all modes

1.46.3   Syntax Description

instance-id

Optional. OSPF instance ID. The range of values is 1 to 65,535.

area-id

Optional. Area ID. The range of values is 0 to 4,294,967,295.

ip-addr

Optional. Area IP address.

all

Optional. Displays all opaque Type 9 LSAs.

link-id

Optional. LSA ID in the form A.B.C.D.

self-originate

Optional. Displays self-originated LSAs.

detail

Optional. Provides detailed information.

1.46.4   Default

None

1.46.5   Usage Guidelines

Use the show ospf database link-scope-opaque command to display information about OSPF opaque Type 9 LSAs. Type 9 Opaque LSAs are not flooded beyond the local network.

Note:  
By default, most show commands (in any mode) display information for the current context only or, depending on the command syntax, for all contexts. If you are an administrator for the local context, you can insert the optional context ctx-name construct, preceding the show command, to view output for the specified context without entering that context. For more information about using the context ctx-name construct, see the context command description.

Note:  
By appending a space followed by the pipe ( | ) character at the end of a show command, you can filter the output using a set of modifier keywords and arguments. For more information, see “Modifying Output of show Commands” in Using the CLI.

1.46.6   Examples

The following example displays OSPF area scope opaque (Type 9) LSA information:

[local]Redback>show ospf database link-scope-opaque
  --- OSPF Link State Database for Instance 1/Router ID 193.10.25.7 ---



       Link scope Opaque Link State Advertisements (Interface 10.1.1.1)

LinkID          AdvertisingRtr   Sequence #  ChkSm  Option Length LSAge

3.0.0.0         10.1.2.2         80000001    9d11   E,O    44     3

1.47   show ospf database network

show ospf database [instance-id] [area-id | ip-addr] network [all | link-id] [router-id | self-originate]] [detail]

1.47.1   Purpose

Displays information about Open Shortest Path First (OSPF) network link-state advertisements (LSAs).

1.47.2   Command Mode

all modes

1.47.3   Syntax Description

instance-id

Optional. OSPF instance ID. The range of values is 1 to 65,535.

area-id

Optional. Area ID. The range of values is 0 to 4,294,967,295.

ip-addr

Optional. Area IP address.

all

Optional. Displays all network LSAs.

link-id

Optional. LSA ID in the form A.B.C.D.

router-id

Optional. OSPF router ID in the form A.B.C.D.

self-originate

Optional. Displays self-originated LSAs.

detail

Optional. Provides detailed information.

1.47.4   Default

None

1.47.5   Usage Guidelines

Use the show ospf database network command to display information about OSPF network LSAs.

Note:  
By default, most show commands (in any mode) display information for the current context only or, depending on the command syntax, for all contexts. If you are an administrator for the local context, you can insert the optional context ctx-name construct, preceding the show command, to view output for the specified context without entering that context. For more information about using the context ctx-name construct, see the context command description.

Note:  
By appending a space followed by the pipe ( | ) character at the end of a show command, you can filter the output using a set of modifier keywords and arguments. For more information, see “Modifying Output of show Commands” in Using the CLI.

1.47.6   Examples

The following example displays information specific to network LSAs:

[local]Redback>show ospf database 1 0.0.0.1 network
--- OSPF Link State Database for Instance 1/Router ID 193.10.25.7 ---



                Network Link State Advertisements (Area 0.0.0.1)

LinkID        AdvertisingRtr   Sequence #  ChkSm  Option Length LSAge

10.1.1.1      193.10.25.7      80000001    f824   E      32     189 

10.2.2.2      33.33.33.33      80000001    9157   E      32     147 

10.3.1.1      193.10.25.7      80000001    9e5    E      32     176 

The following example provides detailed information specific to network LSAs:

[local]Redback>show ospf database 1 0.0.0.1 network detail
--- OSPF Link State Database for Instance 1/Router ID 193.10.25.7 ---



         --- Network LSA 10.1.1.1 (Area 0.0.0.1) ---



Link State Id    :  10.1.1.1        Advertising Router  : 193.10.25.7

Sequence Number  :  0x80000001      Checksum            : 0xf824

Options          :  E               Length              : 32

Network Mask     :  255.255.0.0     LinkCount           : 2

Age              :  197



Attached Routers : 193.10.25.7, 22.22.22.22



        --- Network LSA 10.2.2.2 (Area 0.0.0.1) ---



Link State Id    :  10.2.2.2        Advertising Router  : 33.33.33.33

Sequence Number  :  0x80000001      Checksum            : 0x9157

Options          : E                Length              : 32

Network Mask     : 255.255.0.0      LinkCount           : 2

Age              : 155

Attached Routers : 33.33.33.33, 22.22.22.22

1.48   show ospf database nssa

show ospf database [instance-id] [area-id | ip-addr] nssa [all | link-id] [router-id | self-originate]] [detail]

1.48.1   Purpose

Displays information about Open Shortest Path First (OSPF) not-so-stubby-area (NSSA) link-state advertisements (LSAs).

1.48.2   Command Mode

all modes

1.48.3   Syntax Description

instance-id

Optional. OSPF instance ID. The range of values is 1 to 65,535.

area-id

Optional. Area ID. The range of values is 0 to 4,294,967,295.

ip-addr

Optional. Area IP address.

all

Optional. Displays all NSSA LSAs.

link-id

Optional. LSA ID in the form A.B.C.D.

router-id

Optional. OSPF router ID in the form A.B.C.D.

self-originate

Optional. Displays self-originated LSAs.

detail

Optional. Provides detailed information.

1.48.4   Default

None

1.48.5   Usage Guidelines

Use the show ospf database nssa command to display information about OSPF NSSA LSAs.

Note:  
By default, most show commands (in any mode) display information for the current context only or, depending on the command syntax, for all contexts. If you are an administrator for the local context, you can insert the optional context ctx-name construct, preceding the show command, to view output for the specified context without entering that context. For more information about using the context ctx-name construct, see the context command description.

Note:  
By appending a space followed by the pipe ( | ) character at the end of a show command, you can filter the output using a set of modifier keywords and arguments. For more information, see “Modifying Output of show Commands” in Using the CLI.

1.48.6   Examples

The following example displays output from the show ospf database nssa command:

[local]Redback>show ospf database nssa
  --- OSPF Link State Database for Instance 1/Router ID 10.200.1.1 ---



             NSSA Link State Advertisements (Area 0.0.0.12)

LinkID           AdvertisingRtr   Sequence #  ChkSm Option Length LSAge

0.0.0.0          10.200.1.1       80000021    1db          36     1154

1.49   show ospf database router

show ospf database [instance-id] [area-id | ip-addr] router [all | link-id] [router-id | self-originate]] [detail]

1.49.1   Purpose

Displays information about Open Shortest Path First (OSPF) router link-state advertisements (LSAs).

1.49.2   Command Mode

all modes

1.49.3   Syntax Description

instance-id

Optional. OSPF instance ID. The range of values is 1 to 65,535.

area-id

Optional. Area ID. The range of values is 0 to 4,294,967,295.

ip-addr

Optional. Area IP address.

all

Optional. Displays all router LSAs.

link-id

Optional. LSA ID in the form A.B.C.D.

router-id

Optional. OSPF router ID in the form A.B.C.D.

self-originate

Optional. Displays self-originated LSAs.

detail

Optional. Provides detailed information.

1.49.4   Default

None

1.49.5   Usage Guidelines

Use the show ospf database router command to display information about OSPF router LSAs.

Note:  
By default, most show commands (in any mode) display information for the current context only or, depending on the command syntax, for all contexts. If you are an administrator for the local context, you can insert the optional context ctx-name construct, preceding the show command, to view output for the specified context without entering that context. For more information about using the context ctx-name construct, see the context command description.

Note:  
By appending a space followed by the pipe ( | ) character at the end of a show command, you can filter the output using a set of modifier keywords and arguments. For more information, see “Modifying Output of show Commands” in Using the CLI.

1.49.6   Examples

The following example displays output from the show ospf database router command:

[local]Redback>show ospf database router
  --- OSPF Link State Database for Instance 1/Router ID 10.200.1.1 ---



             Router Link State Advertisements (Area 0.0.0.0)

LinkID         AdvertisingRtr   Sequence # ChkSm Option Length   LSAge

10.200.1.1     10.200.1.1       80000026   c2aa  E,O    36       1252



             Router Link State Advertisements (Area 0.0.0.11)

LinkID         AdvertisingRtr   Sequence # ChkSm  Option Length  LSAge

10.200.1.1     10.200.1.1       8000002b   c2a4   E,O    36      1252



             Router Link State Advertisements (Area 0.0.0.12)

LinkID         AdvertisingRtr   Sequence #  ChkSm  Option Length  LSAge

10.200.1.1     10.200.1.1       80000022    73dd   NP,O  24      1302

1.50   show ospf database summary-asbr

show ospf database [instance-id] [area-id | ip-addr] summary-asbr [all | link-id] [router-id | self-originate]] [detail]

1.50.1   Purpose

Displays information about Open Shortest Path First (OSPF) Type 4 summary autonomous system boundary router (ASBR) link-state advertisements (LSAs).

1.50.2   Command Mode

all modes

1.50.3   Syntax Description

instance-id

Optional. OSPF instance ID. The range of values is 1 to 65,535.

area-id

Optional. Area ID. The range of values is 0 to 4,294,967,295.

ip-addr

Optional. Area IP address.

all

Optional. Displays all Type 4 summary ASBR LSAs.

link-id

Optional. LSA ID in the form A.B.C.D.

router-id

Optional. OSPF router ID in the form A.B.C.D.

self-originate

Optional. Displays self-originated LSAs.

detail

Optional. Provides detailed information.

1.50.4   Default

None

1.50.5   Usage Guidelines

Use the show ospf database summary-asbr command to display information about OSPF Type 4 summary ASBR LSAs.

Note:  
By default, most show commands (in any mode) display information for the current context only or, depending on the command syntax, for all contexts. If you are an administrator for the local context, you can insert the optional context ctx-name construct, preceding the show command, to view output for the specified context without entering that context. For more information about using the context ctx-name construct, see the context command description.

Note:  
By appending a space followed by the pipe ( | ) character at the end of a show command, you can filter the output using a set of modifier keywords and arguments. For more information, see “Modifying Output of show Commands” in Using the CLI.

1.50.6   Examples

The following example displays output from the show ospf database summary-asbr command:

[local]Redback>show ospf database summary-asbr
  --- OSPF Link State Database for Instance 1/Router ID 193.10.25.7 ---



      Summary AS Border Router Link State Advertisements (Area 0.0.0.1)

LinkID           AdvertisingRtr   Sequence #  ChkSm Option Length LSAge

19.4.123.89      33.33.33.33      80000001    9159  E      28     27

19.4.123.89      193.10.25.7      80000001    790a  E      28     26

1.51   show ospf database summary-network

show ospf database [instance-id] [area-id | ip-addr] summary-network [all | link-id] [router-id | self-originate] [detail]

1.51.1   Purpose

Displays information about Open Shortest Path First (OSPF) Type 3 summary network link-state advertisements (LSAs).

1.51.2   Command Mode

all modes

1.51.3   Syntax Description

instance-id

Optional. OSPF instance ID. The range of values is 1 to 65,535.

area-id

Optional. Area ID. The range of values is 0 to 4,294,967,295.

ip-addr

Optional. Area IP address.

all

Optional. Displays all Type 3 summary network LSAs.

link-id

Optional. LSA ID in the form A.B.C.D.

router-id

Optional. OSPF router ID in the form A.B.C.D.

self-originate

Optional. Displays self-originated LSAs.

detail

Optional. Provides detailed information.

1.51.4   Default

Displays link-state database information for all OSPF instances.

1.51.5   Usage Guidelines

Use the show ospf database summary-network command to display information about OSPF Type 3 summary network LSAs.

Note:  
By default, most show commands (in any mode) display information for the current context only or, depending on the command syntax, for all contexts. If you are an administrator for the local context, you can insert the optional context ctx-name construct, preceding the show command, to view output for the specified context without entering that context. For more information about using the context ctx-name construct, see the context command description.

Note:  
By appending a space followed by the pipe ( | ) character at the end of a show command, you can filter the output using a set of modifier keywords and arguments. For more information, see “Modifying Output of show Commands” in Using the CLI.

1.51.6   Examples

The following example displays output from the show ospf database summary-network command:

[local]Redback>show ospf database summary-network
--- OSPF Link State Database for Instance 1/Router ID 10.200.1.1 ---



             Summary Network Link State Advertisements (Area 0.0.0.0)

LinkID          AdvertisingRtr   Sequence #  ChkSm Option Length LSAge

10.200.1.2      10.200.1.1       80000021    b898  E,O    28     1638



             Summary Network Link State Advertisements (Area 0.0.0.11)

LinkID          AdvertisingRtr   Sequence #  ChkSm  Option Length LSAge

10.200.1.1      10.200.1.1       80000021    c28f   E,O    28     1638



             Summary Network Link State Advertisements (Area 0.0.0.12)

LinkID          AdvertisingRtr   Sequence #  ChkSm  Option Length LSAge

10.200.1.1      10.200.1.1       80000021    68e3   NP,O   28     1603

10.200.1.2      10.200.1.1       80000021    5eec   NP,O   28     1603

1.52   show ospf debug

show ospf debug

1.52.1   Purpose

Displays Open Shortest Path First (OSPF) debug settings.

1.52.2   Command Mode

all modes

1.52.3   Syntax Description

This command has no keywords or arguments.

1.52.4   Default

None

1.52.5   Usage Guidelines

Use the show ospf debug command to display OSPF debug settings.

Note:  
By default, most show commands (in any mode) display information for the current context only or, depending on the command syntax, for all contexts. If you are an administrator for the local context, you can insert the optional context ctx-name construct, preceding the show command, to view output for the specified context without entering that context. For more information about using the context ctx-name construct, see the context command description.

Note:  
By appending a space followed by the pipe ( | ) character at the end of a show command, you can filter the output using a set of modifier keywords and arguments. For more information, see “Modifying Output of show Commands” in Using the CLI.

1.52.6   Examples

The following example displays output from the show ospf debug command when the debug ospf packet, debug ospf lsdb, and debug ospf rib commands have been enabled in exec mode:

[local]Redback>show ospf debug
OSPF:

   packet hello send debugging is turned on

   packet hello recv debugging is turned on

   packet lsu send debugging is turned on

   packet lsu recv debugging is turned on

   packet lsr send debugging is turned on

   packet lsr recv debugging is turned on

   packet dd send debugging is turned on

   packet dd recv debugging is turned on

   packet ack send debugging is turned on

   packet ack recv debugging is turned on

   lsdb type1 debugging is turned on

   lsdb type2 debugging is turned on

   lsdb type3 debugging is turned on

   lsdb type4 debugging is turned on

   lsdb type5 debugging is turned on

   lsdb type7 debugging is turned on

   rib debugging is turned on 

1.53   show ospf interface

show ospf interface [ip-addr | if-name] [detail]

1.53.1   Purpose

Displays Open Shortest Path First (OSPF) interface information.

1.53.2   Command Mode

all modes

1.53.3   Syntax Description

ip-addr

Optional. IP address of a particular interface.

if-name

Optional. Name of a particular interface.

detail

Optional. Displays detailed information.

1.53.4   Default

Displays summary information about all configured OSPF interfaces in the context.

1.53.5   Usage Guidelines

Use the show ospf interface command to display OSPF interface information. Use this command without any keywords or arguments to display summary information for all configured OSPF interfaces in the context. Use the ip-addr or if-name argument to display information about a specific OSPF interface. Use the detail keyword to display additional information.

Note:  
By default, most show commands (in any mode) display information for the current context only or, depending on the command syntax, for all contexts. If you are an administrator for the local context, you can insert the optional context ctx-name construct, preceding the show command, to view output for the specified context without entering that context. For more information about using the context ctx-name construct, see the context command description.

Note:  
By appending a space followed by the pipe ( | ) character at the end of a show command, you can filter the output using a set of modifier keywords and arguments. For more information, see “Modifying Output of show Commands” in Using the CLI.

1.53.6   Examples

The following example displays summary OSPF interface information:

[local]Redback>show ospf interface
  --- OSPF Interfaces for Instance 1/Router ID 193.10.25.7 ---



Addr            Len  NetworkType     Cost    Priority State     Area

192.168.5.2     16   broadcast       1       1        BDR       0.0.0.0

193.10.25.7     32   loopback        1       N/A      Loopback  0.0.0.0

10.1.1.1        16   broadcast       1       1        DR        0.0.0.1

10.3.1.1        16   broadcast       1       1        DR        0.0.0.1

The following example displays in-depth information specific to the 192.168.5.2 interface:

[local]Redback>show ospf interface 192.168.5.2 detail
  --- OSPF Interface 192.168.5.2 Area 0.0.0.0 Instance 1 ---



Network Type   : broadcast         Mask           : 255.255.255.0  

Cost           : 1                 Logical Intf   : 2/10

MTU            : 1500              Physical Intf  : ethernet 2/10

State          : BDR               Priority       : 1              

Hello Interval : 0                 Dead Interval  : 1              

Transmit Delay : 1                 Retransmit Int : 5              

DR Router ID   : 10.10.10.16       DR IP Address  : 76.10.2.1      

BDR Router ID  : 10.10.10.15       BDR IP Address : 76.10.2.2      

Ack Queued     : 0                 Flood Queued   : 0              

Ack Delay      : 2                 Authentication : None           

LSA Count      : 0                 LSA Checksum   : 0              

Demand Circuit : No                Flood Reduction: No             

Fast Hello     : Enabled           Hello's per sec: 5   <<< =====

1.54   show ospf neighbor

show ospf neighbor [neighbor-id | interface [ip-addr | if-name]] [detail]

1.54.1   Purpose

Displays Open Shortest Path First (OSPF) neighbor information.

1.54.2   Command Mode

all modes

1.54.3   Syntax Description

neighbor-id

Optional. ID of the neighbor for which information is displayed.

interface

Optional. Displays information for the specified neighbor interface.

ip-addr

Optional. IP address of the interface.

if-name

Optional. Interface name.

detail

Optional. Displays detailed information.

1.54.4   Default

Displays summary information for all OSPF neighbors.

1.54.5   Usage Guidelines

Use the show ospf neighbor command to display OSPF neighbor information.

Note:  
By default, most show commands (in any mode) display information for the current context only or, depending on the command syntax, for all contexts. If you are an administrator for the local context, you can insert the optional context ctx-name construct, preceding the show command, to view output for the specified context without entering that context. For more information about using the context ctx-name construct, see the context command description.

Note:  
By appending a space followed by the pipe ( | ) character at the end of a show command, you can filter the output using a set of modifier keywords and arguments. For more information, see “Modifying Output of show Commands” in Using the CLI.

1.54.6   Examples

The following example provides information on all OSPF neighbors for OSPF instance 1 on the SmartEdge router, 193.10.25.7:

[local]Redback>show ospf neighbor
--- OSPF Neighbors for Instance 1/Router ID 193.10.25.7 ---



NeighborID    NeighborAddress Pri State  DR-State IntfAddress  TimeLeft

19.4.123.89   193.4.4.1       1   Full   DR       193.4.5.2    35

22.22.22.22   10.1.2.2        1   Full   BDR      10.1.1.1     37

33.33.33.33   10.3.2.2        1   Full   BDR      10.3.1.1     32

The following example provides detailed information about all OSPF neighbors:

[local]Redback>show ospf neighbor detail


--- OSPF Neighbor 1.1.1.1 Area 0.0.0.0 Instance 1 --- 


Address : 13.13.13.1 Interface Addr : 13.13.13.2

State : Full DR State : Other 

Cost : 1 DR Priority : 1

DR Router ID : 0.0.0.0      BDR Router ID : 0.0.0.0

LSA Request : 0             LSA Retrans : 0 

DB Exchange : 0             Time Till Dead : 38 

Hello Options : E           DD Options : E,O

LDP/IGP SYNC : In           Progress Metric is : Poisoned

The following example provides information specific to the OSPF neighbor with router ID, 10.3.1.1:

[local]Redback>show ospf neighbor 10.3.1.1
--- OSPF Neighbors for Instance 1/Router ID 193.10.25.7 ---



NeighborID   NeighborAddress Pri  State   DR-State IntfAddress TimeLeft

33.33.33.33  10.3.2.2        1    Full    BDR      10.3.1.1    36

The following example provides detailed information specific to the OSPF neighbor with router ID, 10.3.1.1:

[local]Redback>show ospf neighbor 10.3.1.1 detail
  --- OSPF Neighbor 33.33.33.33 Area 0.0.0.1 Instance 1 ---



Address        : 10.3.2.2          Interface Addr : 10.3.1.1

State          : Full              DR State       : BDR

Cost           : 1                 DR Priority    : 1

DR Router ID   : 10.3.1.1          BDR Router ID  : 10.3.2.2

LSA Request    : 0                 LSA Retrans    : 0

DB Exchange    : 0                 Time Till Dead : 34

Hello Options : E           DD Options : E,O

LDP/IGP SYNC : In           Progress Metric is : Poisoned

1.55   show ospf route

show ospf route [instance-id] [ip-addr [/prefix-length] | external | inter-area | intra-area | redistributed | summary | vpn] [detail]

1.55.1   Purpose

Displays Open Shortest Path First (OSPF) route information.

1.55.2   Command Mode

all modes

1.55.3   Syntax Description

instance-id

Optional. OSPF instance ID. The range of values is 1 to 65,535.

ip-addr

Optional. IP address in the form A.B.C.D.

prefix-length

Optional. Prefix length. The range of values is 0 to 32.

external

Optional. Displays all external routes.

inter-area

Optional. Displays all interarea routes.

intra-area

Optional. Displays all intra-area routes.

redistributed

Optional. Displays routes redistributed from other routing protocols.

summary

Optional. Displays route summary information.

vpn

Optional. Displays redistributed Virtual Private Network (VPN) routes. This option is only available in a VPN context.

detail

Optional. Displays detailed route information.

1.55.4   Default

Displays basic route information for all instances.

1.55.5   Usage Guidelines

Use the show ospf route command to display OSPF route information.

Note:  
By default, most show commands (in any mode) display information for the current context only or, depending on the command syntax, for all contexts. If you are an administrator for the local context, you can insert the optional context ctx-name construct, preceding the show command, to view output for the specified context without entering that context. For more information about using the context ctx-name construct, see the context command description.

Note:  
By appending a space followed by the pipe ( | ) character at the end of a show command, you can filter the output using a set of modifier keywords and arguments. For more information, see “Modifying Output of show Commands” in Using the CLI.

1.55.6   Examples

The following example displays a summary of all OSPF routes:

[local]Redback>show ospf route 
--- OSPF Routes for Instance 1/Router ID 193.10.25.7 ---



Destination       Type      Dest-Type/Proto  Cost  Nhops  Nhop

7.0.0.0/8         EXT T2    Net              20    1      193.4.4.1 

8.0.0.0/8         EXT T2    Net              20    1      193.4.4.1 

9.9.9.0/24        EXT T2    Net              20    1      193.4.4.1 

10.2.0.0/16       Intra     Net              2     2      10.1.2.2 

19.4.123.89/32    Intra     Net              2     1      193.4.4.1 

20.1.1.0/24       Intra     Net              11    1      193.4.4.1 

The following example displays detailed information for OSPF routes:

[local]Redback>show ospf route detail
--- OSPF Routes for Instance 64001/Router ID 10.100.1.5 ---



Destination    : 10.12.208.0/21       Type           : Intra

Dest-type      : Net                  Cost           : 2

Version        : 20                   SPF Count      : 43

Area           : 0.0.0.0              Distance       : 110

Back Link Data : 255.255.248.0

LSDB Type      :                      LSDB ID        : 10.12.215.255

LSDB Adv Router: 10.100.1.1           Next Hop Count : 1

Next Hops      : 10.100.11.9



Destination    : 10.100.1.102/32      Type           : Intra

Dest-type      : Net                  Cost           : 2

Version        : 9                    SPF Count      : 43

Area           : 0.0.0.11             Distance       : 110

Back Link Data : 255.255.255.255

LSDB Type      :                      LSDB ID        : 10.100.1.102

LSDB Adv Router: 10.100.1.102         Next Hop Count : 1

Next Hops      : 10.100.11.50



Destination    : 10.100.11.0/29       Type           : Intra

Dest-type      : Net                  Cost           : 2

Version        : 19                   SPF Count      : 43

Area           : 0.0.0.0              Distance       : 110

Back Link Data : 10.100.11.1

LSDB Type      : Net                  LSDB ID        : 10.100.11.2

LSDB Adv Router: 10.100.1.3           Next Hop Count : 1

Next Hops      : 10.100.11.9

The following example displays VPN route information for OSPF instance 1:

[local]Redback>show ospf route 1 vpn
       --- OSPF Routes for Instance 1/Router ID 10.1.2.2 ---



Destination        Type       Dest-Type/Proto  Cost  Nhops  Nhop

10.3.0.0/16        REDIST-INT Redist/OSPF      2     1      10.2.2.2

20.1.1.0/24        REDIST-INT Redist/OSPF      2     1      10.2.2.2

The following example displays detailed VPN route information for OSPF instance 1:

[local]Redback>show ospf route 1 vpn detail
       --- OSPF Routes for Instance 1/Router ID 10.1.2.2 ---



Destination    : 10.3.0.0/16        Type           : REDIST-INT

Source-Proto   : OSPF               Cost           : 2

Version        : 0                  Redist Level   : Backbone and NSSAs

Next Hop Count : 1

Next Hops      : 10.2.2.2

VPN Route Type : Stub-Network       VPN Options    : 0x0

VPN Domain ID  : 0.0.0.0            VPN Area ID    : 0.0.0.1

VPN Router ID  : 10.1.2.2

Route Flags    : redistributed,vpn-info,vpn-inter-area





Destination    : 20.1.1.0/24        Type           : REDIST-INT

Source-Proto   : OSPF               Cost           : 2

Version        : 0                  Redist Level   : Backbone and NSSAs

Next Hop Count : 1

Next Hops      : 10.2.2.2

VPN Route Type : Summary-Network    VPN Options    : 0x0

VPN Domain ID  : 0.0.0.0            VPN Area ID    : 0.0.0.1

VPN Router ID  : 10.1.2.2

Route Flags    : redistributed,vpn-info,vpn-inter-area

1.56   show ospf route vpn

show ospf route vpn [detail]

1.56.1   Purpose

Displays Open Shortest Path First (OSPF) route information in a Virtual Private Network (VPN) context.

1.56.2   Command Mode

all modes

1.56.3   Syntax Description

detail

Optional. Displays detailed route information.

1.56.4   Default

Displays basic route information for all instances in the specified VPN context.

1.56.5   Usage Guidelines

Use the show ospf route vpn command to displays OSPF route information in a VPN context.

Note:  
By default, most show commands (in any mode) display information for the current context only or, depending on the command syntax, for all contexts. If you are an administrator for the local context, you can insert the optional context ctx-name construct, preceding the show command, to view output for the specified context without entering that context. For more information about using the context ctx-name construct, see the context command description.

Note:  
By appending a space followed by the pipe ( | ) character at the end of a show command, you can filter the output using a set of modifier keywords and arguments. For more information, see “Modifying Output of show Commands” in Using the CLI.

1.56.6   Examples

The following example displays summary information for all OSPF routes in a VPN context:

[local]Redback>show ospf route vpn
       --- OSPF Routes for Instance 1/Router ID 10.1.2.2 ---



Destination        Type       Dest-Type/Proto  Cost  Nhops  Nhop

10.3.0.0/16        REDIST-INT Redist/OSPF      2     1      10.2.2.2

20.1.1.0/24        REDIST-INT Redist/OSPF      2     1      10.2.2.2

The following example displays detailed information for each OSPF route in a VPN context:

[local]Redback>show ospf route vpn detail
       --- OSPF Routes for Instance 1/Router ID 10.1.2.2 ---



Destination    : 10.3.0.0/16        Type           : REDIST-INT

Source-Proto   : OSPF               Cost           : 2

Version        : 0                  Redist Level   : Backbone and NSSAs

Next Hop Count : 1

Next Hops      : 10.2.2.2

VPN Route Type : Stub-Network       VPN Options    : 0x0

VPN Domain ID  : 0.0.0.0            VPN Area ID    : 0.0.0.1

VPN Router ID  : 10.1.2.2

Route Flags    : redistributed,vpn-info,vpn-inter-area





Destination    : 20.1.1.0/24        Type           : REDIST-INT

Source-Proto   : OSPF               Cost           : 2

Version        : 0                  Redist Level   : Backbone and NSSAs

Next Hop Count : 1

Next Hops      : 10.2.2.2

VPN Route Type : Summary-Network    VPN Options    : 0x0

VPN Domain ID  : 0.0.0.0            VPN Area ID    : 0.0.0.1

VPN Router ID  : 10.1.2.2

Route Flags    : redistributed,vpn-info,vpn-inter-area

1.57   show ospf spf

show ospf spf [last | log | scheduling] [instance-id]

1.57.1   Purpose

Displays Open Shortest Path First (OSPF) Shortest Path First (SPF) calculation statistics.

1.57.2   Command Mode

all modes

1.57.3   Syntax Description

last

Optional. Displays the most recent SPF route calculation.

log

Optional. Displays the SPF calculation timing log.

scheduling

Optional. Displays the SPF route calculation scheduling log.

instance-id

Optional. OSPF instance ID. Displays SPF information only for the specified instance.

1.57.4   Default

Displays SPF information for all configured instances of OSPF.

1.57.5   Usage Guidelines

Use the show ospf spf command to display SPF calculation statistics.

Note:  
By default, most show commands (in any mode) display information for the current context only or, depending on the command syntax, for all contexts. If you are an administrator for the local context, you can insert the optional context ctx-name construct, preceding the show command, to view output for the specified context without entering that context. For more information about using the context ctx-name construct, see the context command description.

Note:  
By appending a space followed by the pipe ( | ) character at the end of a show command, you can filter the output using a set of modifier keywords and arguments. For more information, see “Modifying Output of show Commands” in Using the CLI.

1.57.6   Examples

The following example displays all SPF information for all OSPF instances:

[local]Redback>show ospf spf 
--- OSPF Routes for Instance 64001/Router ID 10.100.1.5 ---



Destination    : 10.12.208.0/21       Type           : Intra

Dest-type      : Net                  Cost           : 2

Version        : 20                   SPF Count      : 43

Area           : 0.0.0.0              Distance       : 110

Back Link Data : 255.255.248.0

LSDB Type      :                      LSDB ID        : 10.12.215.255

LSDB Adv Router: 10.100.1.1           Next Hop Count : 1

Next Hops      : 10.100.11.9

Destination    : 10.100.1.102/32      Type           : Intra

Dest-type      : Net                  Cost           : 2

Version        : 9                    SPF Count      : 43

Area           : 0.0.0.11             Distance       : 110

Back Link Data : 255.255.255.255

LSDB Type      :                      LSDB ID        : 10.100.1.102

LSDB Adv Router: 10.100.1.102         Next Hop Count : 1

Next Hops      : 10.100.11.50



Destination    : 10.100.11.0/29       Type           : Intra

Dest-type      : Net                  Cost           : 2

Version        : 19                   SPF Count      : 43

Area           : 0.0.0.0              Distance       : 110

Back Link Data : 10.100.11.1

LSDB Type      : Net                  LSDB ID        : 10.100.11.2

LSDB Adv Router: 10.100.1.3           Next Hop Count : 1

Next Hops      : 10.100.11.9

The following example displays the most recent SPF route calculation for OSPF instance 64001:

[local]Redback>show ospf spf last 64001
   --- Most Recent OSPF SPF Route Calculation ---



When (elapsed)  Instance/Area         Phase     Duration

01:47:51        64001/N/A             External  < 10 ms

The following example displays the SPF calculation timing log:

[local]Redback>show ospf spf log
   --- OSPF SPF Route Calculation Timing Log  ---



     Maximum SPF-Phase Timings

When (elapsed)  Instance/Area         Phase     Duration

1d 02:06:27     64001/0.0.0.11        Intra     20 ms

1d 02:06:27     64001/0.0.0.0         Summary   10 ms

02:01:59        64001/N/A             External  < 10 ms



     Most Recent SPF-Phase Timings

When (elapsed)  Instance/Area         Phase     Duration

02:01:59        64001/N/A             External  < 10 ms

02:02:05        64001/N/A             External  < 10 ms

02:02:09        64001/N/A             External  < 10 ms

02:02:09        64001/0.0.0.0         Summary   < 10 ms

02:02:09        64001/0.0.0.0         Intra     < 10 ms

02:02:09        64001/0.0.0.11        Intra     < 10 ms

02:02:10        64001/N/A             External  < 10 ms

02:02:10        64001/0.0.0.0         Summary   < 10 ms

02:02:10        64001/0.0.0.0         Intra     < 10 ms

02:02:10        64001/0.0.0.11        Intra     < 10 ms

02:02:31        64001/N/A             External  < 10 ms

02:02:31        64001/0.0.0.0         Summary   < 10 ms

02:02:31        64001/0.0.0.0         Intra     < 10 ms

02:02:31        64001/0.0.0.11        Intra     < 10 ms

02:02:45        64001/N/A             External  < 10 ms

02:02:55        64001/N/A             External  < 10 ms

02:02:55        64001/0.0.0.0         Summary   < 10 ms 

1.58   show ospf statistics

show ospf statistics [instance-id] [interface {ip-addr | if-name} | neighbor [ip-addr | interface {ip-addr | if-name}]]

1.58.1   Purpose

Displays Open Shortest Path First (OSPF) statistics.

1.58.2   Command Mode

all modes

1.58.3   Syntax Description

instance-id

Optional. Instance ID. The range of values is 1 to 65,535.

interface ip-addr

Optional. Interface IP address. Displays OSPF statistics for the specified interface. When used with neighbor keyword, displays OSPF statistics for all neighbors on the specified interface.

interface if-name

Optional. Interface name. Displays OSPF statistics for the specified interface. When used with neighbor keyword, displays OSPF statistics for all neighbors on the specified interface.

neighbor

Optional. Displays neighbor statistics.

ip-addr

Optional. IP address of the neighbor interface for which OSPF statistics are displayed.

1.58.4   Default

None

1.58.5   Usage Guidelines

Use the show ospf statistics command to display OSPF statistics.

Note:  
By default, most show commands (in any mode) display information for the current context only or, depending on the command syntax, for all contexts. If you are an administrator for the local context, you can insert the optional context ctx-name construct, preceding the show command, to view output for the specified context without entering that context. For more information about using the context ctx-name construct, see the context command description.

Note:  
By appending a space followed by the pipe ( | ) character at the end of a show command, you can filter the output using a set of modifier keywords and arguments. For more information, see “Modifying Output of show Commands” in Using the CLI.

1.58.6   Examples

The following example displays statistics for all configured OSPF interfaces and neighbors:

[local]Redback>show ospf statistics
  --- OSPF Statistics for Instance 64001 ---

Max flood queue length   : 2           Interval            : 1d 03:10:09
LSAs received            : 1300        LSAs send           : 1333
LSAs changes received    : 130
Packet Retransmissions   : 14          LSA Retransmissions : 24
Routes downloaded        : 20          Routes deleted      : 11
Download Errors          : 0           RIB IPC messages    : 17

             Hello    DD       LSR      LSU      ACK
       Send  29350    74       5        761      628
       Recv  27783    28       10       663      681 

The following example displays statistics for the ospf1 interface:

[local]Redback>show ospf statistics interface ospf1 
  --- OSPF Statistics for Interface 10.10.1.1/Instance 64001 ---

Interface Events    : 1           Interval            : 01:56:35
LSAs received       : 0           LSAs sent           : 0
Max ACK queue length: 0           Max flood queue size: 0

              Hello    DD       LSR      LSU      ACK
        Send  0        0        0        0        0
        Recv  0        0        0        0        0 

The following example displays OSPF statistics for the neighbor with the 10.100.1.3 router ID:

[local]Redback>show ospf statistics neighbor 10.100.1.3
  --- OSPF Statistics for Neighbor 10.100.1.3/Interface 10.100.11.27/Instance 64001---

Neighbor events           : 19581  Interval               : 1d 03:14:30
Packet retransmissions    : 1      LSA retransmissions    : 1
Adjacency lost count      : 0      Adjacency up time      : 1d 03:14:28
Max retransmit queue size : 3      Max request queue size : 9
Exchange timeout count    : 0      Max DD queue size      : 2 

1.59   show ospf summary-address

show ospf summary-address [instance-id]

1.59.1   Purpose

Displays Open Shortest Path First (OSPF) summary address information.

1.59.2   Command Mode

all modes

1.59.3   Syntax Description

instance-id

Optional. OSPF instance ID. The range of values is 1 to 65,535.

1.59.4   Default

None

1.59.5   Usage Guidelines

Use the show ospf summary-address command to display OSPF summary address information.

Note:  
By default, most show commands (in any mode) display information for the current context only or, depending on the command syntax, for all contexts. If you are an administrator for the local context, you can insert the optional context ctx-name construct, preceding the show command, to view output for the specified context without entering that context. For more information about using the context ctx-name construct, see the context command description.

Note:  
By appending a space followed by the pipe ( | ) character at the end of a show command, you can filter the output using a set of modifier keywords and arguments. For more information, see “Modifying Output of show Commands” in Using the CLI.

1.59.6   Examples

The following example displays OSPF summary address information:

[local]Redback>show ospf summary-address
--- OSPF Summaries for Instance 1/Router ID 10.100.1.5 ---



Prefix          Length  Tag       Type          Status    Metric

10.10.0.0       32      0x0       advertise     inactive 

1.60   show ospf vpn

show ospf vpn [instance-id]

1.60.1   Purpose

Displays Virtual Private Network (VPN) information and VPN redistributed route counts for an Open Shortest Path First (OSPF) instance in a VPN context.

1.60.2   Command Mode

all modes

1.60.3   Syntax Description

instance-id

Optional. OSPF instance ID. The range of values is 1 to 65535.

1.60.4   Default

None

1.60.5   Usage Guidelines

Use the show ospf vpn command to display VPN information and VPN redistributed route counts for an OSPF instance in a VPN context.

Note:  
By default, most show commands (in any mode) display information for the current context only or, depending on the command syntax, for all contexts. If you are an administrator for the local context, you can insert the optional context ctx-name construct, preceding the show command, to view output for the specified context without entering that context. For more information about using the context ctx-name construct, see the context command description.

Note:  
By appending a space followed by the pipe ( | ) character at the end of a show command, you can filter the output using a set of modifier keywords and arguments. For more information, see “Modifying Output of show Commands” in Using the CLI.

1.60.6   Examples

The following example displays VPN information and VPN redistributed route counts for OSPF instance 1:

[local]Redback>show ospf vpn 1
  --- OSPF Instance 1/Router ID 10.1.2.2 ---



Domain ID       : 1.1.1.1           Domain Tag      : 0x00000002

Internal Routes : 2                 External Routes : 0